| Age | Commit message (Collapse) | Author |
|---|
|
The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.
Update all EM users which access 'power' field and assume the value is
in milli-Watts.
Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.
Example calculation which shows the rounding error and impact:
power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz
power_a_uW = (100 * 600mW * 600mW * 500MHz) / 10^6 = 18000
power_a_mW = (100 * 600mW * 600mW * 500MHz) / 10^9 = 18
power_b_uW = (100 * 605mW * 605mW * 600MHz) / 10^6 = 21961
power_b_mW = (100 * 605mW * 605mW * 600MHz) / 10^9 = 21
max_freq = 2000MHz
cost_a_mW = 18 * 2000MHz/500MHz = 72
cost_a_uW = 18000 * 2000MHz/500MHz = 72000
cost_b_mW = 21 * 2000MHz/600MHz = 70 // <- artificially better
cost_b_uW = 21961 * 2000MHz/600MHz = 73203
The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull OPP (Operating Performance Points) updates for 5.19-rc1 from Viresh
Kumar:
- Minor update to dt-binding for Qcom's opp-v2-kryo-cpu (Yassine
Oudjana).
- Use list iterator only inside the list_for_each_entry loop (Xiaomeng
Tong, and Jakob Koschel).
- New APIs related to finding OPP based on interconnect bandwidth
(Krzysztof Kozlowski).
- Fix the missing of_node_put() in _bandwidth_supported() (Dan
Carpenter).
- Cleanups (Krzysztof Kozlowski, and Viresh Kumar).
* tag 'opp-updates-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Reorder definition of ceil/floor helpers
opp: Add apis to retrieve opps with interconnect bandwidth
dt-bindings: opp: opp-v2-kryo-cpu: Remove SMEM
opp: use list iterator only inside the loop
opp: replace usage of found with dedicated list iterator variable
PM: opp: simplify with dev_err_probe()
OPP: call of_node_put() on error path in _bandwidth_supported()
|
|
Reorder the helpers to keep all freq specific ones, followed by level
and bw.
No functional change.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add dev_pm_opp_find_bw_ceil and dev_pm_opp_find_bw_floor to retrieve opps
based on interconnect associated with the opp and bandwidth. The index
variable is the index of the interconnect as specified in the opp table
in Devicetree.
Co-developed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The .active_power() callback passes the device pointer when it's called.
Aligned with a convetion present in other subsystems and pass the 'dev'
as a first argument. It looks more cleaner.
Adjust all affected drivers which implement that API callback.
Suggested-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate dedicated pointer variable [1].
In this case, use a new variable 'iter' as the list iterator, while
use the old variable 'new_dev' as a dedicated pointer to point to the
found entry. And BUG_ON(!new_dev);.
[1]: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This code does not call of_node_put(opp_np) if of_get_next_available_child()
returns NULL. But it should.
Fixes: 45679f9b508f ("opp: Don't parse icc paths unnecessarily")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The Energy Model (EM) can be created based on DT entry:
'dynamic-power-coefficient'. It's a 'simple' EM which is limited to the
dynamic power. It has to fit into the math formula which requires also
information about voltage. Some of the platforms don't expose voltage
information, thus it's not possible to use EM registration using DT.
This patch aims to fix it. It introduces new implementation of the EM
registration callback. The new mechanism relies on the new OPP feature
allowing to get power (which is coming from "opp-microwatt" DT property)
expressed in micro-Watts.
The patch also opens new opportunity to better support platforms, which
have a decent static power. It allows to register the EM based on real
power measurements which models total power (static + dynamic), so better
reflects real HW.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add new property to the OPP: power value. The OPP entry in the DT can have
"opp-microwatt". Add the needed code to handle this new property in the
existing infrastructure.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
It is difficult to find which OPPs are active at the moment, specially
if there are multiple OPPs with same frequency available in the device
tree (controlled by supported hardware feature).
Expose name of the DT node to find out the exact OPP.
While at it, also expose level field.
Reported-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Fix sparse warning:
drivers/opp/of.c:924 _opp_add_static_v2() warn: passing zero to 'ERR_PTR'
For duplicate OPPs 'ret' be set to zero.
Fixes: deac8703da5f ("PM / OPP: _of_add_opp_table_v2(): increment count only if OPP is added")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add resource-managed variants of dev_pm_opp_of_add_table_indexed() and
dev_pm_opp_of_add_table_noclk(), allowing drivers to remove boilerplate
code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[ Viresh: Added underscore to devm_of_add_table_indexed() ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Elements of the 'names' array are not changed by the code, constify them
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The 'required-opps' property is optional. So of_count_phandle_with_args()
can return -ENOENT when queried for required-opps. Handle this case.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
* pm-pci:
PCI: PM: Enable PME if it can be signaled from D3cold
PCI: PM: Avoid forcing PCI_D0 for wakeup reasons inconsistently
PCI: Use pci_update_current_state() in pci_enable_device_flags()
* pm-sleep:
PM: sleep: unmark 'state' functions as kernel-doc
PM: sleep: check RTC features instead of ops in suspend_test
PM: sleep: s2idle: Replace deprecated CPU-hotplug functions
* pm-domains:
PM: domains: Fix domain attach for CONFIG_PM_OPP=n
arm64: dts: sc7180: Add required-opps for i2c
PM: domains: Add support for 'required-opps' to set default perf state
opp: Don't print an error if required-opps is missing
* powercap:
powercap: Add Power Limit4 support for Alder Lake SoC
powercap: intel_rapl: Replace deprecated CPU-hotplug functions
|
|
|
|
Commit 4fa82a87ba55 ("opp: Allow required-opps to be used for non genpd
use cases") dereferences the pointers in required_opp_tables but these
might be set to an ERR_PTR if the list still has lazy links pending,
resulting in segfaults. Prior to this patch IS_ERR was also checked on
required_opp_tables[i] before reading ->is_genpd inside
_opp_table_alloc_required_tables, which is at the same time the
predicate to add this table to the lazy list. This segfault is solved
by reordering the checks to bail on lazy pending tables before reading
->is_genpd.
Fixes: 4fa82a87ba55 ("opp: Allow required-opps to be used for non genpd use cases")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The 'required-opps' property is considered optional, hence remove
the pr_err() in of_parse_required_opp() when we find the property is
missing.
While at it, also fix the return value of
of_get_required_opp_performance_state() when of_parse_required_opp()
fails, return a -ENODEV instead of the -EINVAL.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current_opp is released only when whole OPP table is released,
otherwise it's only marked as removed by dev_pm_opp_remove_table().
Functions like dev_pm_opp_put_clkname() and dev_pm_opp_put_supported_hw()
are checking whether OPP table is empty and it's not if current_opp is
set since it holds the refcount of OPP, this produces a noisy warning
from these functions about busy OPP table. Remove the checks to fix it.
Cc: stable@vger.kernel.org
Fixes: 81c4d8a3c414 ("opp: Keep track of currently programmed OPP")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This WARN can be triggered per-core and the stack trace is not useful.
Replace it with plain dev_err(). Fix a comment while at it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Don't limit required_opp_table to genpd only. One possible use case is
cpufreq based devfreq governor, which can use required-opps property to
derive devfreq from cpufreq.
Though the OPP core still doesn't support non-genpd required-opps in
_set_required_opps().
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[ Viresh: Update _set_required_opps() to check for genpd ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Using list_del_init() instead of list_del() + INIT_LIST_HEAD()
to simpify the code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make devm_pm_opp_attach_genpd() to return error code instead of
opp_table pointer in order to have return type consistent with the
other resource-managed OPP helpers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make devm_pm_opp_register_set_opp_helper() to return error code instead
of opp_table pointer in order to have return type consistent with the
other resource-managed OPP helpers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add devres wrapper for dev_pm_opp_of_add_table() to simplify drivers
code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add devres wrapper for dev_pm_opp_set_supported_hw() to simplify drivers
code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add devres wrapper for dev_pm_opp_set_regulators() to simplify drivers
code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add devres wrapper for dev_pm_opp_set_clkname() to simplify drivers code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We are required to call dev_pm_opp_put() from outside of the
opp_table->lock as debugfs removal needs to happen lock-less to avoid
circular dependency issues.
commit cf1fac943c63 ("opp: Reduce the size of critical section in
_opp_kref_release()") tried to fix that introducing a new routine
_opp_get_next() which keeps returning OPPs that can be freed by the
callers and this routine shall be called without holding the
opp_table->lock.
Though the commit overlooked the fact that the OPPs can be referenced by
other users as well and this routine will end up dropping references
which were taken by other users and hence freeing the OPPs prematurely.
In effect, other users of the OPPs will end up having invalid pointers
at hand. We didn't see any crash reports earlier as the exact situation
never happened, though it is certainly possible.
We need a way to mark which OPPs are no longer referenced by the OPP
core, so we don't drop extra references to them accidentally.
This commit adds another OPP flag, "removed", which is used to track
this. And now we should never end up dropping extra references to the
OPPs.
Cc: v5.11+ <stable@vger.kernel.org> # v5.11+
Fixes: cf1fac943c63 ("opp: Reduce the size of critical section in _opp_kref_release()")
Signed-off-by: Beata Michalska <beata.michalska@arm.com>
[ Viresh: Almost rewrote entire patch, added new "removed" field,
rewrote commit log and added the correct Fixes tag. ]
Co-developed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We skip the OPP update if the current and target OPPs are same. This is
fine for the devices that don't support frequency but may cause issues
for the ones that need to program frequency.
An OPP entry doesn't really signify a single operating frequency but
rather the highest frequency at which the other properties of the OPP
entry apply. And we may reach here with different frequency values,
while all of them would point to the same OPP entry in the OPP table.
We just need to update the clock frequency in that case, though in order
to not add special exit points we reuse the code flow from a normal
path.
While at it, rearrange the conditionals in the 'if' statement to check
'enabled' flag at the end.
Fixes: 81c4d8a3c414 ("opp: Keep track of currently programmed OPP")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[ Viresh: Improved commit log and subject, rename current_freq as
current_rate, document it, remove local variable and rearrange
code. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add a function that allows looking up required OPPs given a source OPP
table, destination OPP table and the source OPP.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[ Viresh: Rearranged code, fixed return errors ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Not all devices that need to use OPP core need to have clocks, a missing
clock is fine in which case -ENOENT shall be returned by clk_get().
Anything else is an error and must be handled properly.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The bandwidth must be scaled at a different point in the code flow based
on if we are scaling up or down the frequency, otherwise this may cause
undesired effects as the device will try to use more of the memory
bandwidth which may be shared across several devices. Much like how
regulators and required-opps are programmed.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Reported-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
The OPP core currently requires the required opp tables to be available
before the dependent OPP table is added, as it needs to create links
from the dependent OPP table to the required ones. This may not be
convenient for all the platforms though, as this requires strict
ordering for probing the drivers.
This patch allows lazy-linking of the required-opps. The OPP tables for
which the required-opp-tables aren't available at the time of their
initialization, are added to a special list of OPP tables:
lazy_opp_tables. Later on, whenever a new OPP table is registered with
the OPP core, we check if it is required by an OPP table in the pending
list; if yes, then we complete the linking then and there.
An OPP table is marked unusable until the time all its required-opp
tables are available. And if lazy-linking fails for an OPP table, the
OPP core disables all of its OPPs to make sure no one can use them.
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
All the users have migrated to dev_pm_opp_set_opp() now, get rid of the
duplicate API, dev_pm_opp_set_bw(), which only performs a part of the new API.
While at it, remove the unnecessary parameter to _set_opp_bw().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
The new helper dev_pm_opp_set_opp() can be used for configuring the
devices for a particular OPP and can be used by different type of
devices, even the ones which don't change frequency (like power
domains).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Drop the unnecessary parameters and follow the pattern from
_generic_set_opp_regulator().
While at it, also remove the local variable old_freq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
In order to avoid conditional statements at the caller site, this patch
updates _generic_set_opp_clk_only() to work for devices that don't
change frequency (like power domains, etc.). Return 0 if the clk pointer
passed to this routine is not valid.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
The _generic_set_opp_regulator() helper will be used for devices which
don't change frequency (like power domains, etc.) later on, prepare for
that by not relying on frequency for making decisions here.
While at it, update its parameters to pass only what is necessary.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
The _set_opp() helper will be used for devices which don't change frequency
(like power domains, etc.) later on, prepare for that by not relying on
frequency for making decisions here.
While at it, also update the debug print to contain all relevant
information.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
The _set_opp() helper will be used for devices which don't change their
frequency (like power domains, etc.) later on, prepare for that by
breaking the generic part out of dev_pm_opp_set_rate().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
The dev_pm_opp_set_rate() helper needs to know the currently programmed
OPP to make few decisions and currently we try to find it on every
invocation of this routine.
Lets start keeping track of the current_opp programmed for the devices
of the opp table, that will be quite useful going forward.
If we fail to find the current OPP, we pick the first one available in
the list, as the list is in ascending order of frequencies, level, or
bandwidth and that's the best guess we can make anyway.
Note that we used to do the frequency comparison a bit early in
dev_pm_opp_set_rate() previously, and now instead we check the target
opp, which shall be more accurate anyway.
We need to make sure that current_opp's memory doesn't get freed while
it is being used and so we keep a reference of it until the time it is
used.
Now that current_opp will always be set, we can drop some unnecessary
checks as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Clock is not optional for users who call into dev_pm_opp_set_rate().
Remove the unnecessary checks.
While at it also drop the local variable for clk and use opp_table->clk
instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
This routine has nothing to do with frequency, it just disables all the
resources previously enabled. Rename it to match its purpose.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Check whether OPP table has regulators in _set_opp_custom() and set up
dev_pm_set_opp_data accordingly. Now _set_opp_custom() works properly,
i.e. it doesn't crash if OPP table doesn't have assigned regulators.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[ Viresh: Rearrange the routine a bit ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Until now the ->set_opp() helper (i.e. special implementation for
setting the OPPs for platforms) was implemented only to take care of
multiple regulators case, but going forward we would need that for other
use cases as well.
This patch prepares for that by allocating the regulator specific part
from dev_pm_opp_set_regulators() and the opp helper part from
dev_pm_opp_register_set_opp_helper().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Print OPP level in debug message of _opp_add_static_v2(). This helps to
chase GENPD bugs.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
NVIDIA Tegra SoCs have a power domains topology such that child domains
only clamp a power rail, while parent domain controls shared performance
state of the multiple child domains. In this case child's domain doesn't
need to have OPP table. Hence we want to allow children power domains to
pass performance state to the parent domain if child's domain doesn't have
OPP table.
The dev_pm_opp_xlate_performance_state() gets src_table=NULL if a child
power domain doesn't have OPP table and in this case we should pass the
performance state to the parent domain.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
