| Age | Commit message (Collapse) | Author |
|---|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit abf545484d31 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The rw_page users were not converted to use bio/req ops. As a result
bdev_write_page is not passing down REQ_OP_WRITE and the IOs will
be sent down as reads.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixes: 4e1b2d52a80d ("block, fs, drivers: remove REQ_OP compat defs and related code")
Modified by me to:
1) Drop op_flags passing into ->rw_page(), as we don't use it.
2) Make op_is_write() and friends safe to use for !CONFIG_BLOCK
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
|
|
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
|
|
Prefix the sector number being cleared with a '0x' to make it clear that
this is a hex value.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Currently, presence of direct_access() in block_device_operations
indicates support of DAX on its block device. Because
block_device_operations is instantiated with 'const', this DAX
capablity may not be enabled conditinally.
In preparation for supporting DAX to device-mapper devices, add
QUEUE_FLAG_DAX to request_queue flags to advertise their DAX
support. This will allow to set the DAX capability based on how
mapped device is composed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <linux-s390@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The __pmem address space was meant to annotate codepaths that touch
persistent memory and need to coordinate a call to wmb_pmem(). Now that
wmb_pmem() is gone, there is little need to keep this annotation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit writes to media on system shutdown or pmem driver unload.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Given that nvdimm_flush() has higher overhead than wmb_pmem() (pointer
chasing through nd_region), and that we otherwise assume a platform has
ADR capability when flush hints are not present, move nvdimm_flush() to
REQ_FLUSH context.
Note that we still arrange for nvdimm_flush() to be called even in the
ADR case. We need at least once wmb() fence to push buffered writes in
the cpu out to the ADR protected domain.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
nvdimm_flush() is a replacement for the x86 'pcommit' instruction. It is
an optional write flushing mechanism that an nvdimm bus can provide for
the pmem driver to consume. In the case of the NFIT nvdimm-bus-provider
nvdimm_flush() is implemented as a series of flush-hint-address [1]
writes to each dimm in the interleave set (region) that backs the
namespace.
The nvdimm_has_flush() routine relies on platform firmware to describe
the flushing capabilities of a platform. It uses the heuristic of
whether an nvdimm bus provider provides flush address data to return a
ternary result:
1: flush addresses defined
0: dimm topology described without flush addresses (assume ADR)
-errno: no topology information, unable to determine flush mechanism
The pmem driver is expected to take the following actions on this ternary
result:
1: nvdimm_flush() in response to REQ_FUA / REQ_FLUSH and shutdown
0: do not set, WC or FUA on the queue, take no further action
-errno: warn and then operate as if nvdimm_has_flush() returned '0'
The caveat of this heuristic is that it can not distinguish the "dimm
does not have flush address" case from the "platform firmware is broken
and failed to describe a flush address". Given we are already
explicitly trusting the NFIT there's not much more we can do beyond
blacklisting broken firmwares if they are ever encountered.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Currently phys_to_pfn_t() is an exported symbol to allow nfit_test to
override it and indicate that nfit_test-pmem is not device-mapped. Now,
we want to enable nfit_test to operate without DMA_CMA and the pmem it
provides will no longer be physically contiguous, i.e. won't be capable
of supporting direct_access requests larger than a page. Make
pmem_direct_access() a weak symbol so that it can be replaced by the
tools/testing/nvdimm/ version, and move phys_to_pfn_t() to a static
inline now that it no longer needs to be overridden.
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Clean up needless calls to the action routine by letting
devm_add_action_or_reset() call it automatically. This does cause the
disk to registered and immediately unregistered when a memory allocation
fails, but the block layer should be prepared for such an event.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
|
|
For autodetecting a previously established dax configuration we need the
info block to indicate block-device vs device-dax mode, and we need to
have the default namespace probe hand-off the configuration to the
dax_pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
1/ If a mapping overlaps a bad sector fail the request.
2/ Do not opportunistically report more dax-capable capacity than is
requested when errors present.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[vishal: fix a conflict with system RAM collision patches]
[vishal: add a 'size' parameter to ->direct_access]
[vishal: fix a conflict with DAX alignment check patches]
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
The devm conversion obviates the need to continue to remember the queue
and disk locally in the driver.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Now that pmem internals have been disentangled from pfn setup, that code
can move to the core. This is in preparation for adding another user of
the pfn-device capabilities.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In preparation for providing an alternative (to block device) access
mechanism to persistent memory, convert pmem_rw_bytes() to
nsio_rw_bytes(). This allows ->rw_bytes() functionality without
requiring a 'struct pmem_device' to be instantiated.
In other words, when ->rw_bytes() is in use i/o is driven through
'struct nd_namespace_io', otherwise it is driven through 'struct
pmem_device' and the block layer. This consolidates the disjoint calls
to devm_exit_badblocks() and devm_memunmap() into a common
devm_nsio_disable() and cleans up the init path to use a unified
pmem_attach_disk() implementation.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The leading '0x' in front of %pa is redundant, also we can just use %pR
to simplify the print statement. The request parameters can be directly
taken from the resource as well.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Register a callback to clean up the request_queue and put the gendisk at
driver disable time.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Save a pointer chase by storing the driver private data in the
request_queue rather than the gendisk.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pass the device performing the probe so we can use a devm allocation for
the btt superblock.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pass the device performing the probe so we can use a devm allocation for
the pfn superblock.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
We can derive the common namespace from other information. We also do
not need to cache it because all the usages are in slow paths.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The ACPI specification does not specify the state of data after a clear
poison operation. Potential future libnvdimm bus implementations for
other architectures also might not specify or disagree on the state of
data after clear poison. Clarify why we write twice.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Three fixes, the first two are tagged for -stable:
- The ndctl utility/library gained expanded unit tests illuminating a
long standing bug in the libnvdimm SMART data retrieval
implementation.
It has been broken since its initial implementation, now fixed.
- Another one line fix for the detection of stale info blocks.
Without this change userspace can get into a situation where it is
unable to reconfigure a namespace.
- Fix the badblock initialization path in the presence of the new (in
v4.6-rc1) section alignment workarounds.
Without this change badblocks will be reported at the wrong offset.
These have received a build success report from the kbuild robot and
have appeared in -next with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
libnvdimm, pfn: fix uuid validation
libnvdimm: fix smart data retrieval
|
|
When section alignment padding is in effect we need to shift / truncate
the range that is queried for poison by the 'start_pad' or 'end_trunc'
reservations.
It's easiest if we just pass in an adjusted resource range rather than
deriving it from the passed in namespace. With the resource range
resolution pushed out to the caller we can also push the
namespace-to-region lookup to the caller and drop the implicit pmem-type
assumption about the passed in namespace object.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the definition of memcpy_from_pmem() to return 0 or a negative
error code. Implement x86/arch_memcpy_from_pmem() with memcpy_mcsafe().
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
|
|
If a write is directed at a known bad block perform the following:
1/ write the data
2/ send a clear poison command
3/ invalidate the poison out of the cache hierarchy
Cc: <x86@kernel.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When we enounter a bad block we need to kunmap_atomic() before
returning.
Cc: <stable@vger.kernel.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When alloc_disk(0) or alloc_disk-node(0, XX) is used, the ->major
number is completely ignored: all devices are allocated with a
major of BLOCK_EXT_MAJOR.
So there is no point allocating pmem_major.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
drivers/nvdimm/pmem.c: In function 'nvdimm_namespace_attach_pfn':
drivers/nvdimm/pmem.c:367:3: error: implicit declaration of function
'__phys_to_pfn' [-Werror=implicit-function-declaration]
.base_pfn = __phys_to_pfn(nsio->res.start),
ia64 does not provide __phys_to_pfn(), just use the PHYS_PFN() alias.
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
On a platform where 'Persistent Memory' and 'System RAM' are mixed
within a given sparsemem section, trim the namespace and notify about the
sub-optimal alignment.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The altmap for a section-misaligned namespace needs to arrange for the
base_pfn to be section-aligned. As a result the 'reserve' region (pfns
from base that do not have a struct page) must be increased. Otherwise
we trip the altmap validation check in __add_pages:
if (altmap->base_pfn != phys_start_pfn
|| vmem_altmap_offset(altmap) > nr_pages) {
pr_warn_once("memory add fail, invalid altmap\n");
return -EINVAL;
}
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In preparation for asynchronous address range scrub support add an
ability for the pmem driver to dynamically consume address range scrub
results.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
A recent bugfix changed pfn_t to always be 64-bit wide, but did not
change the code in pmem.c, which is now broken on 32-bit architectures
as reported by gcc:
In file included from ../drivers/nvdimm/pmem.c:28:0:
drivers/nvdimm/pmem.c: In function 'pmem_alloc':
include/linux/pfn_t.h:15:17: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define PFN_DEV (1ULL << (BITS_PER_LONG_LONG - 3))
This changes the intermediate pfn_flags in struct pmem_device to
be 64 bit wide as well, so they can store the flags correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db78c22230d0 ("mm: fix pfn_t vs highmem")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
get_dev_page() enables paths like get_user_pages() to pin a dynamically
mapped pfn-range (devm_memremap_pages()) while the resulting struct page
objects are in use. Unlike get_page() it may fail if the device is, or
is in the process of being, disabled. While the initial lookup of the
range may be an expensive list walk, the result is cached to speed up
subsequent lookups which are likely to be in the same mapped range.
devm_memremap_pages() now requires a reference counter to be specified
at init time. For pmem this means moving request_queue allocation into
pmem_alloc() so the existing queue usage counter can track "device
pages".
ZONE_DEVICE pages always have an elevated count and will never be on an
lru reclaim list. That space in 'struct page' can be redirected for
other uses, but for safety introduce a poison value that will always
trip __list_add() to assert. This allows half of the struct list_head
storage to be reclaimed with some assurance to back up the assumption
that the page count never goes to zero and a list_add() is never
attempted.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before the dynamically allocated struct pages from devm_memremap_pages()
can be put to use outside the driver, we need a mechanism to track
whether they are still in use at teardown. Towards that goal reorder
the initialization sequence to allow the 'q_usage_counter' from the
request_queue to be used by the devm_memremap_pages() implementation (in
subsequent patches).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the new vmem_altmap capability to enable the pmem driver to arrange
for a struct page memmap to be established in persistent memory.
[linux@roeck-us.net: mn10300: declare __pfn_to_phys() to fix build error]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In support of providing struct page for large persistent memory
capacities, use struct vmem_altmap to change the default policy for
allocating memory for the memmap array. The default vmemmap_populate()
allocates page table storage area from the page allocator. Given
persistent memory capacities relative to DRAM it may not be feasible to
store the memmap in 'System Memory'. Instead vmem_altmap represents
pre-allocated "device pages" to satisfy vmemmap_alloc_block_buf()
requests.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are several scenarios where we need to retrieve and update
metadata associated with a given devm_memremap_pages() mapping, and the
only lookup key available is a pfn in the range:
1/ We want to augment vmemmap_populate() (called via arch_add_memory())
to allocate memmap storage from pre-allocated pages reserved by the
device driver. At vmemmap_alloc_block_buf() time it grabs device pages
rather than page allocator pages. This is in support of
devm_memremap_pages() mappings where the memmap is too large to fit in
main memory (i.e. large persistent memory devices).
2/ Taking a reference against the mapping when inserting device pages
into the address_space radix of a given inode. This facilitates
unmap_mapping_range() and truncate_inode_pages() operations when the
driver is tearing down the mapping.
3/ get_user_pages() operations on ZONE_DEVICE memory require taking a
reference against the mapping so that the driver teardown path can
revoke and drain usage of device pages.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For the purpose of communicating the optional presence of a 'struct
page' for the pfn returned from ->direct_access(), introduce a type that
encapsulates a page-frame-number plus flags. These flags contain the
historical "page_link" encoding for a scatterlist entry, but can also
denote "device memory". Where "device memory" is a set of pfns that are
not part of the kernel's linear mapping by default, but are accessed via
the same memory controller as ram.
The motivation for this new type is large capacity persistent memory
that needs struct page entries in the 'memmap' to support 3rd party DMA
(i.e. O_DIRECT I/O with a persistent memory source/target). However,
we also need it in support of maintaining a list of mapped inodes which
need to be unmapped at driver teardown or freeze_bdev() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave@sr71.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Support badblock checking in all the pmem read paths that do not go
through the block layer. This protects info block reads (btt or pfn) as
well as data reads to a pmem namespace via a btt instance.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Longer term teach dax to punch "error" holes in mapping requests and
deliver SIGBUS to applications that consume a bad pmem page. For now,
simply disable the dax performance optimization in the presence of known
errors.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Check the sectors specified in a read bio to see if they hit a known bad
block, and return an error code pmem_do_bvec().
Note that the ->rw_page() is not in a position to return errors. For
now, copy the same layering violation present in zram_rw_page() to avoid
crashes of the form:
kernel BUG at mm/filemap.c:822!
[..]
Call Trace:
[<ffffffff811c540e>] page_endio+0x1e/0x60
[<ffffffff81290d29>] mpage_end_io+0x39/0x60
[<ffffffff8141c4ef>] bio_endio+0x3f/0x60
[<ffffffffa005c491>] pmem_make_request+0x111/0x230 [nd_pmem]
...i.e. unlock a page that was already unlocked via pmem_rw_page() =>
page_endio().
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
