summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)Author
2024-06-01Merge tag 'ath-current-20240531' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath Merge ath-current from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git ath.git fixes for 6.10. Two fixes for user reported regressions in ath11k. One dependency fix and one error path fix.
2024-05-23wifi: ath11k: move power type check to ASSOC stage when connecting to 6 GHz APBaochen Qiang
With commit bc8a0fac8677 ("wifi: mac80211: don't set bss_conf in parsing") ath11k fails to connect to 6 GHz AP. This is because currently ath11k checks AP's power type in ath11k_mac_op_assign_vif_chanctx() which would be called in AUTH stage. However with above commit power type is not available until ASSOC stage. As a result power type check fails and therefore connection fails. Fix this by moving power type check to ASSOC stage, also move regulatory rules update there because it depends on power type. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Fixes: bc8a0fac8677 ("wifi: mac80211: don't set bss_conf in parsing") Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240424064019.4847-1-quic_bqiang@quicinc.com
2024-05-23wifi: ath11k: fix WCN6750 firmware crash caused by 17 num_vdevsCarl Huang
WCN6750 firmware crashes because of num_vdevs changed from 4 to 17 in ath11k_init_wmi_config_qca6390() as the ab->hw_params.num_vdevs is 17. This is caused by commit f019f4dff2e4 ("wifi: ath11k: support 2 station interfaces") which assigns ab->hw_params.num_vdevs directly to config->num_vdevs in ath11k_init_wmi_config_qca6390(), therefore WCN6750 firmware crashes as it can't support such a big num_vdevs. Fix it by assign 3 to num_vdevs in hw_params for WCN6750 as 3 is sufficient too. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01371-QCAMSLSWPLZ-1 Fixes: f019f4dff2e4 ("wifi: ath11k: support 2 station interfaces") Reported-by: Luca Weiss <luca.weiss@fairphone.com> Tested-by: Luca Weiss <luca.weiss@fairphone.com> Closes: https://lore.kernel.org/r/D15TIIDIIESY.D1EKKJLZINMA@fairphone.com/ Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240520030757.2209395-1-quic_cjhuang@quicinc.com
2024-05-22tracing/treewide: Remove second parameter of __assign_str()Steven Rostedt (Google)
With the rework of how the __string() handles dynamic strings where it saves off the source string in field in the helper structure[1], the assignment of that value to the trace event field is stored in the helper value and does not need to be passed in again. This means that with: __string(field, mystring) Which use to be assigned with __assign_str(field, mystring), no longer needs the second parameter and it is unused. With this, __assign_str() will now only get a single parameter. There's over 700 users of __assign_str() and because coccinelle does not handle the TRACE_EVENT() macro I ended up using the following sed script: git grep -l __assign_str | while read a ; do sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file; mv /tmp/test-file $a; done I then searched for __assign_str() that did not end with ';' as those were multi line assignments that the sed script above would fail to catch. Note, the same updates will need to be done for: __assign_str_len() __assign_rel_str() __assign_rel_str_len() I tested this with both an allmodconfig and an allyesconfig (build only for both). [1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/ Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts. Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs Tested-by: Guenter Roeck <linux@roeck-us.net>
2024-05-21Merge tag 'pci-v6.10-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci updates from Bjorn Helgaas: "Enumeration: - Skip E820 checks for MCFG ECAM regions for new (2016+) machines, since there's no requirement to describe them in E820 and some platforms require ECAM to work (Bjorn Helgaas) - Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien Le Moal) - Remove last user and pci_enable_device_io() (Heiner Kallweit) - Wait for Link Training==0 to avoid possible race (Ilpo Järvinen) - Skip waiting for devices that have been disconnected while suspended (Ilpo Järvinen) - Clear Secondary Status errors after enumeration since Master Aborts and Unsupported Request errors are an expected part of enumeration (Vidya Sagar) MSI: - Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas) Error handling: - Mask Genesys GL975x SD host controller Replay Timer Timeout correctable errors caused by a hardware defect; the errors cause interrupts that prevent system suspend (Kai-Heng Feng) - Fix EDR-related _DSM support, which previously evaluated revision 5 but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan) ASPM: - Simplify link state definitions and mask calculation (Ilpo Järvinen) Power management: - Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS apparently doesn't know how to put them back in D0 (Mario Limonciello) CXL: - Support resetting CXL devices; special handling required because CXL Ports mask Secondary Bus Reset by default (Dave Jiang) DOE: - Support DOE Discovery Version 2 (Alexey Kardashevskiy) Endpoint framework: - Set endpoint BAR to be 64-bit if the driver says that's all the device supports, in addition to doing so if the size is >2GB (Niklas Cassel) - Simplify endpoint BAR allocation and setting interfaces (Niklas Cassel) Cadence PCIe controller driver: - Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof Kozlowski) Cadence PCIe endpoint driver: - Configure endpoint BARs to be 64-bit based on the BAR type, not the BAR value (Niklas Cassel) Freescale Layerscape PCIe controller driver: - Convert DT binding to YAML (Frank Li) MediaTek MT7621 PCIe controller driver: - Add DT binding missing 'reg' property for child Root Ports (Krzysztof Kozlowski) - Fix theoretical string truncation in PHY name (Sergio Paracuellos) NVIDIA Tegra194 PCIe controller driver: - Return success for endpoint probe instead of falling through to the failure path (Vidya Sagar) Renesas R-Car PCIe controller driver: - Add DT binding missing IOMMU properties (Geert Uytterhoeven) - Add DT binding R-Car V4H compatible for host and endpoint mode (Yoshihiro Shimoda) Rockchip PCIe controller driver: - Configure endpoint BARs to be 64-bit based on the BAR type, not the BAR value (Niklas Cassel) - Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski) - Set the Subsystem Vendor ID, which was previously zero because it was masked incorrectly (Rick Wertenbroek) Synopsys DesignWare PCIe controller driver: - Restructure DBI register access to accommodate devices where this requires Refclk to be active (Manivannan Sadhasivam) - Remove the deinit() callback, which was only need by the pcie-rcar-gen4, and do it directly in that driver (Manivannan Sadhasivam) - Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean up things like eDMA (Manivannan Sadhasivam) - Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel to dw_pcie_ep_init() (Manivannan Sadhasivam) - Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to reflect the actual functionality (Manivannan Sadhasivam) - Call dw_pcie_ep_init_registers() directly from all the glue drivers, not just those that require active Refclk from the host (Manivannan Sadhasivam) - Remove the "core_init_notifier" flag, which was an obscure way for glue drivers to indicate that they depend on Refclk from the host (Manivannan Sadhasivam) TI J721E PCIe driver: - Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli) - Add DT binding J722S SoC support (Siddharth Vadapalli) TI Keystone PCIe controller driver: - Add DT binding missing num-viewport, phys and phy-name properties (Jan Kiszka) Miscellaneous: - Constify and annotate with __ro_after_init (Heiner Kallweit) - Convert DT bindings to YAML (Krzysztof Kozlowski) - Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming Zhou)" * tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits) PCI: Do not wait for disconnected devices when resuming x86/pci: Skip early E820 check for ECAM region PCI: Remove unused pci_enable_device_io() ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io() PCI: Update pci_find_capability() stub return types PCI: Remove PCI_IRQ_LEGACY scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios Revert "genirq/msi: Provide constants for PCI/IMS support" Revert "x86/apic/msi: Enable PCI/IMS" Revert "iommu/vt-d: Enable PCI/IMS" Revert "iommu/amd: Enable PCI/IMS" Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support" ...
2024-05-20wifi: ath10k: fix QCOM_RPROC_COMMON dependencyDmitry Baryshkov
If ath10k_snoc is built-in, while Qualcomm remoteprocs are built as modules, compilation fails with: /usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_init': drivers/net/wireless/ath/ath10k/snoc.c:1534: undefined reference to `qcom_register_ssr_notifier' /usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_deinit': drivers/net/wireless/ath/ath10k/snoc.c:1551: undefined reference to `qcom_unregister_ssr_notifier' Add corresponding dependency to ATH10K_SNOC Kconfig entry so that it's built as module if QCOM_RPROC_COMMON is built as module too. Fixes: 747ff7d3d742 ("ath10k: Don't always treat modem stop events as crashes") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240511-ath10k-snoc-dep-v1-1-9666e3af5c27@linaro.org
2024-05-17wifi: ath11k: Fix error path in ath11k_pcic_ext_irq_configBreno Leitao
If one of the dummy allocation fails in ath11k_pcic_ext_irq_config(), the previous allocated devices might leak due to returning without deallocating the devices. Instead of returning on the error path, deallocate all the previously allocated net_devices and then return. Fixes: bca592ead825 ("wifi: ath11k: allocate dummy net_device dynamically") Signed-off-by: Breno Leitao <leitao@debian.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240508185902.70975-1-leitao@debian.org
2024-05-16Merge tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds
Pull MMC updates from Ulf Hansson: "MMC core: - Increase the timeout period of the ACMD41 command - Add card entry for quirks to debugfs - Add mmc_gpiod_set_cd_config() function - Store owner from SDIO modules with sdio_register_driver() MMC host: - atmel-mci: Some cleanups and a switch to use dev_err_probe() - renesas_sdhi: - Add support for RZ/G2L, RZ/G3S and RZ/V2M variants - Set the SDBUF after reset - sdhci: Add support for "Tuning Error" interrupts - sdhci-acpi: - Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA - Disable write protect detection on Toshiba WT10-A - Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working - sdhci_am654: - Re-work and fix the tuning support for multiple speed-modes - Add tuning algorithm for delay chain - sdhci-esdhc-imx: Add NXP S32G3 support - sdhci-of-dwcmshc: - Add tuning support for Sophgo CV1800B and SG200X - Implement SDHCI CQE support - sdhci-pci-gli: Use the proper pci_set_power_state() instead of PMCSR writes" MEMSTICK: - Convert a couple of drivers to use the ->remove_new() callback" * tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits) mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list mmc: renesas_sdhi: Set the SDBUF after reset mmc: core: Increase the timeout period of the ACMD41 command mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too mmc: atmel-mci: Switch to use dev_err_probe() mmc: atmel-mci: Incapsulate used to be a platform data into host structure mmc: atmel-mci: Replace platform device pointer by generic one mmc: atmel-mci: Use temporary variable for struct device mmc: atmel-mci: Get rid of platform data leftovers mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning mmc: sdhci-s3c: Choose sdhci_ops based on variant mmc: sdhci_am654: Constify struct sdhci_ops mmc: sdhci-sprd: Constify struct sdhci_ops mmc: sdhci-omap: Constify struct sdhci_ops mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops mmc: slot-gpio: Use irq_handler_t type mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA ...
2024-05-03Merge tag 'ath-next-20240502' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath ath.git patches for v6.10 ath12k * debugfs support * dfs_simulate_radar debugfs file * disable Wireless Extensions * suspend and hibernation support * ACPI support * refactoring in preparation of multi-link support ath11k * support hibernation (required changes in qrtr and MHI subsystems) * ieee80211-freq-limit Device Tree property support ath10k * firmware-name Device Tree property support
2024-05-03wifi: mac80211: handle color change per linkAditya Kumar Singh
In order to support color change with MLO, handle the link ID now passed from cfg80211, adjust the code to do everything per link and call the notifications to cfg80211 correctly. Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://msgid.link/20240422053412.2024075-4-quic_adisi@quicinc.com Link: https://msgid.link/20240422053412.2024075-5-quic_adisi@quicinc.com Link: https://msgid.link/20240422053412.2024075-6-quic_adisi@quicinc.com Link: https://msgid.link/20240422053412.2024075-7-quic_adisi@quicinc.com [squash, move API call updates to this patch] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-05-02wifi: ath12k: fix the problem that down grade phy mode operationLingbo Kong
Currently, when using WCN7850 or QCN9274 as AP, ath12k always performs down grade phy mode operation regardless of whether the firmware supports EHT capability or not and then vdev will start in HE mode. When stations that support EHT capability try to connect to the AP, the AP will set phy mode to EHT after receiving the association request packet, and then send WMI_PEER_ASSOC_CMDID command to firmware, AP’s firmware will crash. This is because when the ath12k_mac_copy_sband_iftype_data() function handles EHT capability, it does not copy the EHT capability into the iftype[band][type] array according to the interface type. So, interface type should not be used as an index to get eht_cap in ath12k_mac_check_down_grade_phy_mode() function. To address this issue, use types_mask to select the eht_cap in ath12k_mac_check_down_grade_phy_mode() function. This patch affects QCN9274 and WCN7850 because they have the same issue. Hostapd log: wlo1: STA 02:03:7f:37:12:34 IEEE 802.11: Could not set STA to kernel driver Kernel log: [270894.816076] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_SET_PARAM cmd [270894.816111] ath12k_pci 0000:03:00.0: failed to setup peer SMPS for vdev 0: -108 [270894.816122] ath12k_pci 0000:03:00.0: Failed to associate station: 02:03:7f:37:12:34 [270894.843389] ieee80211 phy5: Hardware restart was requested [270894.843517] ath12k_pci 0000:03:00.0: failed to lookup peer 02:03:7f:37:12:34 on vdev 0 [270894.843616] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_DELETE cmd [270894.843650] ath12k_pci 0000:03:00.0: failed to delete peer vdev_id 0 addr 02:03:7f:37:12:34 ret -108 [270894.843663] ath12k_pci 0000:03:00.0: Failed to delete peer: 02:03:7f:37:12:34 for VDEV: 0 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240425083837.5340-1-quic_lingbok@quicinc.com
2024-04-30wifi: ar5523: enable proper endpoint verificationNikita Zhandarovich
Syzkaller reports [1] hitting a warning about an endpoint in use not having an expected type to it. Fix the issue by checking for the existence of all proper endpoints with their according types intact. Sadly, this patch has not been tested on real hardware. [1] Syzkaller report: ------------[ cut here ]------------ usb 1-1: BOGUS urb xfer, pipe 3 != type 1 WARNING: CPU: 0 PID: 3643 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 ... Call Trace: <TASK> ar5523_cmd+0x41b/0x780 drivers/net/wireless/ath/ar5523/ar5523.c:275 ar5523_cmd_read drivers/net/wireless/ath/ar5523/ar5523.c:302 [inline] ar5523_host_available drivers/net/wireless/ath/ar5523/ar5523.c:1376 [inline] ar5523_probe+0x14b0/0x1d10 drivers/net/wireless/ath/ar5523/ar5523.c:1655 usb_probe_interface+0x30f/0x7f0 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:560 [inline] really_probe+0x249/0xb90 drivers/base/dd.c:639 __driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778 driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808 __device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936 bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427 __device_attach+0x1e4/0x530 drivers/base/dd.c:1008 bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487 device_add+0xbd9/0x1e90 drivers/base/core.c:3517 usb_set_configuration+0x101d/0x1900 drivers/usb/core/message.c:2170 usb_generic_driver_probe+0xbe/0x100 drivers/usb/core/generic.c:238 usb_probe_device+0xd8/0x2c0 drivers/usb/core/driver.c:293 call_driver_probe drivers/base/dd.c:560 [inline] really_probe+0x249/0xb90 drivers/base/dd.c:639 __driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778 driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808 __device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936 bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427 __device_attach+0x1e4/0x530 drivers/base/dd.c:1008 bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487 device_add+0xbd9/0x1e90 drivers/base/core.c:3517 usb_new_device.cold+0x685/0x10ad drivers/usb/core/hub.c:2573 hub_port_connect drivers/usb/core/hub.c:5353 [inline] hub_port_connect_change drivers/usb/core/hub.c:5497 [inline] port_event drivers/usb/core/hub.c:5653 [inline] hub_event+0x26cb/0x45d0 drivers/usb/core/hub.c:5735 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x669/0x1090 kernel/workqueue.c:2436 kthread+0x2e8/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 </TASK> Reported-and-tested-by: syzbot+1bc2c2afd44f820a669f@syzkaller.appspotmail.com Fixes: b7d572e1871d ("ar5523: Add new driver") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240408121425.29392-1-n.zhandarovich@fintech.ru
2024-04-30wifi: ath12k: fix flush failure in recovery scenariosBaochen Qiang
Commit eaf9f17b861b ("wifi: ath12k: relocate ath12k_dp_pdev_pre_alloc() call") moves ath12k_dp_pdev_pre_alloc() from ath12k_core_start() to ath12k_mac_allocate(), resulting in ath12k_mac_flush() failure in recovery scenarios: [ 6849.684104] ath12k_pci 0000:04:00.0: pdev 0 successfully recovered [ 6854.907320] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0 [ 6860.027353] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0 [ 6865.143385] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0 This is because, with ath12k_dp_pdev_pre_alloc() moved to ath12k_mac_allocate(), dp->num_tx_pending is not reset due to ATH12K_FLAG_REGISTERED set in recovery scenarios. So a possible fix would be to reset that counter at some proper point, just like the old design. But considering that the counter tracks number of packets pending to be freed or returned to mac80211, forcefully reset it might make it hard to expose some real issues. For example if somehow ath12k fails to free/return some TX packets, we don't know that because no warnings any more. That is to say we should not reset that counter during recovery (which is already done due to above commit), instead should decrease it each time a packet is freed/returned. Currently almost each related function has this logic implemented, except ath12k_dp_cc_cleanup(). So add the same there to fix this issue. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240426015434.94840-1-quic_bqiang@quicinc.com
2024-04-30wifi: ath12k: check M3 buffer size as well whey trying to reuse itBaochen Qiang
Currently in recovery/resume cases, we do not free M3 buffer but instead will reuse it. This is done by checking m3_mem->vaddr: if it is not NULL we believe M3 buffer is ready and go ahead to reuse it. Note that m3_mem->size is not checked. This is safe for now because currently M3 reuse logic only gets executed in recovery/resume cases and the size keeps unchanged in either of them. However ideally the size should be checked as well, to make the code safer. So add the check there. Now if that check fails, free old M3 buffer and reallocate a new one. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Fixes: 303c017821d8 ("wifi: ath12k: fix kernel crash during resume") Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240425021740.29221-1-quic_bqiang@quicinc.com
2024-04-29wifi: carl9170: add a proper sanity check for endpointsNikita Zhandarovich
Syzkaller reports [1] hitting a warning which is caused by presence of a wrong endpoint type at the URB sumbitting stage. While there was a check for a specific 4th endpoint, since it can switch types between bulk and interrupt, other endpoints are trusted implicitly. Similar warning is triggered in a couple of other syzbot issues [2]. Fix the issue by doing a comprehensive check of all endpoints taking into account difference between high- and full-speed configuration. [1] Syzkaller report: ... WARNING: CPU: 0 PID: 4721 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 ... Call Trace: <TASK> carl9170_usb_send_rx_irq_urb+0x273/0x340 drivers/net/wireless/ath/carl9170/usb.c:504 carl9170_usb_init_device drivers/net/wireless/ath/carl9170/usb.c:939 [inline] carl9170_usb_firmware_finish drivers/net/wireless/ath/carl9170/usb.c:999 [inline] carl9170_usb_firmware_step2+0x175/0x240 drivers/net/wireless/ath/carl9170/usb.c:1028 request_firmware_work_func+0x130/0x240 drivers/base/firmware_loader/main.c:1107 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x669/0x1090 kernel/workqueue.c:2436 kthread+0x2e8/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308 </TASK> [2] Related syzkaller crashes: Link: https://syzkaller.appspot.com/bug?extid=e394db78ae0b0032cb4d Link: https://syzkaller.appspot.com/bug?extid=9468df99cb63a4a4c4e1 Reported-and-tested-by: syzbot+0ae4804973be759fa420@syzkaller.appspotmail.com Fixes: a84fab3cbfdc ("carl9170: 802.11 rx/tx processing and usb backend") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Acked-By: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422183355.3785-1-n.zhandarovich@fintech.ru
2024-04-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR. Conflicts: drivers/net/ethernet/ti/icssg/icssg_prueth.c net/mac80211/chan.c 89884459a0b9 ("wifi: mac80211: fix idle calculation with multi-link") 87f5500285fb ("wifi: mac80211: simplify ieee80211_assign_link_chanctx()") https://lore.kernel.org/all/20240422105623.7b1fbda2@canb.auug.org.au/ net/unix/garbage.c 1971d13ffa84 ("af_unix: Suppress false-positive lockdep splat for spin_lock() in __unix_gc().") 4090fa373f0e ("af_unix: Replace garbage collection algorithm.") drivers/net/ethernet/ti/icssg/icssg_prueth.c drivers/net/ethernet/ti/icssg/icssg_common.c 4dcd0e83ea1d ("net: ti: icssg-prueth: Fix signedness bug in prueth_init_rx_chns()") e2dc7bfd677f ("net: ti: icssg-prueth: Move common functions into a separate file") No adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25wifi: ath10k: Refer to INTX instead of LEGACYDamien Le Moal
To be consistent with the deprecation of PCI_IRQ_LEGACY and its replacement with PCI_IRQ_INTX, rename macros and functions referencing "legacy irq" to instead use the term "intx irq". Link: https://lore.kernel.org/r/20240325070944.3600338-20-dlemoal@kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-04-25wifi: ath10k: drop fw.eboard file nameDmitry Baryshkov
Follow the example set up by previous commit and drop .fw.eboard setting. Instead always use "eboard.bin" in this case. QCA9984 already uses that file name, any (im)possible future users will just have to use the same file name. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130-wcn3990-board-fw-v1-3-738f7c19a8c8@linaro.org
2024-04-25wifi: ath10k: drop chip-specific board data file nameDmitry Baryshkov
The .fw.board parameter predates board-2.bin support. For all the platforms, which define this parameter, it is equal to "board.bin". Other platforms (like WCN3990) ommit it, limiting the ability to provide board-specific data file. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130-wcn3990-board-fw-v1-2-738f7c19a8c8@linaro.org
2024-04-25wifi: ath10k: populate board data for WCN3990Dmitry Baryshkov
Specify board data size (and board.bin filename) for the WCN3990 platform. Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Fixes: 03a72288c546 ("ath10k: wmi: add hw params entry for wcn3990") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130-wcn3990-board-fw-v1-1-738f7c19a8c8@linaro.org
2024-04-24wifi: ath10k: Fix an error code problem in ↵Su Hui
ath10k_dbg_sta_write_peer_debug_trigger() Clang Static Checker (scan-build) warns: drivers/net/wireless/ath/ath10k/debugfs_sta.c:line 429, column 3 Value stored to 'ret' is never read. Return 'ret' rather than 'count' when 'ret' stores an error code. Fixes: ee8b08a1be82 ("ath10k: add debugfs support to get per peer tids log via tracing") Signed-off-by: Su Hui <suhui@nfschina.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422034243.938962-1-suhui@nfschina.com
2024-04-24wifi: ath12k: set mlo_capable_flags based on QMI PHY capabilityRaj Kumar Bhagat
Currently, mlo_capable_flags is set to zero if dualmac device is detected based on One Time Programmable (OTP) register value. This is not generic and in future dualmac devices may support Single Link Operation (SLO) and Multi Link Operation (MLO). Thus, set mlo_capable_flags based on 'single_chip_mlo_support' parameter from QMI PHY capability response message from the firmware. Also, add check on mlo_capable_flags to disable MLO parameter in the host capability QMI request message. If the firmware does not respond with this optional parameter 'single_chip_mlo_support' in QMI PHY capability response, default ab->mlo_capable_flags is used. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240418125609.3867730-3-quic_rajkbhag@quicinc.com
2024-04-24wifi: ath12k: read single_chip_mlo_support parameter from QMI PHY capabilityRaj Kumar Bhagat
New parameter 'single_chip_mlo_support' was added in QMI PHY capability response message. This is an optional parameter added in QCN9274 firmware. This parameter states if the firmware supports Single-Link Operation (SLO) and Multi-Link Operation (MLO) within the same device. If single_chip_mlo_support = 1, then intra device SLO/MLO is supported in the firmware. If single_chip_mlo_support = 0, then intra device SLO/MLO is not supported in the firmware. Hence, add support to read 'single_chip_mlo_support' parameter from the QMI PHY capability response message. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240418125609.3867730-2-quic_rajkbhag@quicinc.com
2024-04-24wifi: ath12k: add support to handle beacon miss for WCN7850Kang Yang
When AP goes down or too far away without indication to STA, beacon miss will be detected. Then for WCN7850's firmware, it will use roam event to send beacon miss to host. If STA doesn't handle the beacon miss, will keep the fake connection and unable to roam. So add support for WCN7850 to trigger disconnection from AP when receiving this event from firmware. It has to be noted that beacon miss event notification for QCN9274 to be handled in a separate patch as it uses STA kickout WMI event to notify beacon miss and the current STA kickout event is processed as low_ack. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Reviewed-by: Nicolas Escande <nico.escande@gmail.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
2024-04-24wifi: ath11k: allocate dummy net_device dynamicallyBreno Leitao
Embedding net_device into structures prohibits the usage of flexible arrays in the net_device structure. For more details, see the discussion at [1]. Un-embed the net_device from struct ath11k_ext_irq_grp by converting it into a pointer. Then use the leverage alloc_netdev() to allocate the net_device object at ath11k_ahb_config_ext_irq() for ahb, and ath11k_pcic_ext_irq_config() for pcic. The free of the device occurs at ath11k_ahb_free_ext_irq() for the ahb case, and ath11k_pcic_free_ext_irq() for the pcic case. [1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ Signed-off-by: Breno Leitao <leitao@debian.org> Tested-by: Kalle Valo <kvalo@kernel.org> Acked-by: Kalle Valo <kvalo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-24wifi: ath10k: allocate dummy net_device dynamicallyBreno Leitao
Embedding net_device into structures prohibits the usage of flexible arrays in the net_device structure. For more details, see the discussion at [1]. Un-embed the net_device from struct ath10k by converting it into a pointer. Then use the leverage alloc_netdev() to allocate the net_device object at ath10k_core_create(). The free of the device occurs at ath10k_core_destroy(). [1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ Signed-off-by: Breno Leitao <leitao@debian.org> Acked-by: Kalle Valo <kvalo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-23wifi: ath12k: ACPI band edge channel power supportLingbo Kong
Currently, ath12k does not have the ability to set band edge channel power for WCN7850. In order to support this, ath12k gets band edge channel power table in ath12k_acpi_dsm_get_data() function and sets pdev_id and param_type_id, then finally sends these data and WMI_PDEV_SET_BIOS_INTERFACE_CMDID to firmware to set band edge channel power. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-5-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: ACPI CCA threshold supportLingbo Kong
Currently, ath12k does not have the ability to adjust Clear Channel Assessment (CCA) threshold values to meet the regulatory requirements. Get the values from ACPI and send them to the firmware using ath12k_wmi_set_bios_cmd() function. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-4-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: ACPI SAR supportLingbo Kong
In order to enable ACPI SAR (Specific Absorption Rate), ath12k gets SAR and GEO offset tables from ACPI and sends the data to firmware using WMI_PDEV_SET_BIOS_SAR_TABLE_CMDID and WMI_PDEV_SET_BIOS_GEO_TABLE_CMDID commands. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-3-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: ACPI TAS supportLingbo Kong
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable TAS read the tables from ACPI and send them to the firmware using WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI event callback so that ACPI can notify ath12k to get the updated SAR power table and sends it to the firmware when the device state is changed. ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid field. Most likely QCN9274 will never support ACPI as the chip is not used in laptops. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: change supports_suspend to true for WCN7850Baochen Qiang
Now that all things are ready, enable supports_suspend to make suspend/resume work for WCN7850. Don't touch other chips because they don't support suspend. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-11-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: support suspend/resumeBaochen Qiang
Now that all infrastructure is in place and ath12k is fixed to handle all the corner cases, power down the ath12k firmware during suspend and power it back up during resume. For suspend, two conditions needs to be satisfied: 1. since MHI channel unprepare would be done in late suspend stage, ath12k needs to get all QMI-dependent things done before that stage. 2. and because unprepare MHI channels requires a working MHI stack, ath12k is not allowed to call mhi_power_down() until that finishes. So the original suspend callback is separated into two parts: the first part handles all QMI-dependent things in suspend callback; while the second part powers down MHI in suspend_late callback. This is valid because kernel calls ath12k's suspend callback before calling all suspend_late callbacks, making the first condition satisfied. And because MHI devices are children of ath12k device (ab->dev), kernel guarantees that ath12k's suspend_late callback is called after QRTR's suspend_late callback, this satisfies the second condition. Above analysis also applies to resume process. so the original resume callback is separated into two parts: the first part powers up MHI stack in resume_early callback, this guarantees MHI stack is working when QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback after ath12k's resume_early callback, due to the child-father relationship); the second part waits for the completion of restart, which would succeed since MHI channels are ready for use by QMI. Another notable change is in power down path, we tell mhi_power_down() to not to destroy MHI devices, making it possible for QRTR to help unprepare/prepare MHI channels, and finally get us rid of the potential probe-defer issue when resume. Also change related code due to interface changes. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-10-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: avoid stopping mac80211 queues in ath12k_core_restart()Baochen Qiang
Currently when resume ath12k_core_restart() calls ath12k_core_pre_reconfigure_recovery() where mac80211 queues are stopped by calling ieee80211_stop_queues(). Then in ath12k_mac_op_reconfig_complete() those queues are not started because ieee80211_wake_queues() is skipped due to the check on reconfig_type. The result is that mac80211 could not deliver any frame to ath12k to send out, finally making connection fail. [84473.104249] PM: suspend exit [84479.372397] wlan0: no VHT 160 MHz capability on 5 GHz, limiting to 80 MHz [84479.372401] wlan0: determined local STA to be EHT, BW limited to 80 MHz [84479.372416] wlan0: determined AP 00:03:7f:12:b7:b7 to be HE [84479.372420] wlan0: connecting with HE mode, max bandwidth 80 MHz [84479.580348] wlan0: authenticate with 00:03:7f:12:b7:b7 (local address=00:03:7f:37:11:53) [84479.580351] wlan0: send auth to 00:03:7f:12:b7:b7 (try 1/3) [84480.698993] wlan0: send auth to 00:03:7f:12:b7:b7 (try 2/3) [84481.816505] wlan0: send auth to 00:03:7f:12:b7:b7 (try 3/3) [84482.810966] wlan0: authentication with 00:03:7f:12:b7:b7 timed out Actually we don't need to stop/start queues during suspend/resume, so remove ath12k_core_pre_reconfigure_recovery() from ath12k_core_restart(). This won't cause any regression because currently the only chance ath12k_core_restart() gets called is in reset case, where ab->is_reset is set so that function will never be executed. Also remove ath12k_core_post_reconfigure_recovery() because it is not needed in suspend/resume case. This is also valid due to above analysis. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-9-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: no need to handle pktlog during suspend/resumeBaochen Qiang
Currently pktlog is stopped in suspend callback and started in resume callback, and in either scenarios it's basically to delete/modify ab->mon_reap_timer and to purge related rings. For WCN7850 it's pointless because pktlog is not enabled: both ab->mon_reap_timer and those rings are not initialized. So remove pktlog handling in suspend/resume callbacks. And further, remove these two functions and related callee because no one is calling them. Other chips are not affected because now only WCN7850 supports suspend/resume. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-8-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: flush all packets before suspendBaochen Qiang
In order to send out all packets before going to suspend, current code adds a 500ms delay as a workaround. It is a rough estimate and may not work. Fix this by checking packet counters, if counters become zero, then all packets are sent out or dropped. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-7-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: decrease MHI channel buffer length to 8KBBaochen Qiang
Currently buf_len field of ath12k_mhi_config_wcn7850 is assigned with 0, making MHI use a default size, 64KB, to allocate channel buffers. This is likely to fail in some scenarios where system memory is highly fragmented and memory compaction or reclaim is not allowed. For now we haven't get any failure report on this in ath12k, but there indeed is one such case in ath11k [1]. Actually those buffers are used only by QMI target -> host communication. And for WCN7850, the largest packet size for that is less than 6KB. So change buf_len field to 8KB, which results in order 1 allocation if page size is 4KB. In this way, we can at least save some memory, and as well as decrease the possibility of allocation failure in those scenarios. [1] https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/ Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-6-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: fix warning on DMA ring capabilities eventBaochen Qiang
We are seeing below warning in both reset and suspend/resume scenarios: [ 4153.776040] ath12k_pci 0000:04:00.0: Already processed, so ignoring dma ring caps This is because ab->num_db_cap is not cleared in ath12k_wmi_free_dbring_caps(), so clear it to avoid such warnings. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-5-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: do not dump SRNG statistics during resumeBaochen Qiang
Both the firmware reset feature and the power management suspend/resume feature share common power-down and power-up functionality. One aspect of the power-up functionality is the handling of the ATH12K_QMI_EVENT_FW_INIT_DONE event. When this event is received, a call is made to ath12k_hal_dump_srng_stats(), with the purpose to collect information that may be useful in debugging the cause of a firmware reset. Unfortunately, since this functionality is shared between both the firmware reset path and the power management resume path, the kernel log is flooded with messages during resume. Since these messages are not useful during resume, and in fact can be confusing and can increase the time it takes to resume, update the logic to only call ath12k_hal_dump_srng_stats() during firmware reset. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-4-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: remove MHI LOOPBACK channelsBaochen Qiang
There is no driver to match these two channels, so remove them. This fixes warnings from MHI subsystem during suspend: mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-3-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: rearrange IRQ enable/disable in reset pathBaochen Qiang
For non-WoW suspend/resume, ath12k host powers down whole hardware when suspend and powers up it when resume, the code path it goes through is very like the ath12k reset logic. In order to reuse that logic, rearrange IRQ handling in the reset path. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-2-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: fix kernel crash during resumeBaochen Qiang
Currently during resume, QMI target memory is not properly handled, resulting in kernel crash in case DMA remap is not supported: BUG: Bad page state in process kworker/u16:54 pfn:36e80 page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x36e80 page dumped because: nonzero _refcount Call Trace: bad_page free_page_is_bad_report __free_pages_ok __free_pages dma_direct_free dma_free_attrs ath12k_qmi_free_target_mem_chunk ath12k_qmi_msg_mem_request_cb The reason is: Once ath12k module is loaded, firmware sends memory request to host. In case DMA remap not supported, ath12k refuses the first request due to failure in allocating with large segment size: ath12k_pci 0000:04:00.0: qmi firmware request memory request ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 7077888 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 8454144 ath12k_pci 0000:04:00.0: qmi dma allocation failed (7077888 B type 1), will try later with small size ath12k_pci 0000:04:00.0: qmi delays mem_request 2 ath12k_pci 0000:04:00.0: qmi firmware request memory request Later firmware comes back with more but small segments and allocation succeeds: ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 262144 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 65536 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 Now ath12k is working. If suspend is triggered, firmware will be reloaded during resume. As same as before, firmware requests two large segments at first. In ath12k_qmi_msg_mem_request_cb() segment count and size are assigned: ab->qmi.mem_seg_count == 2 ab->qmi.target_mem[0].size == 7077888 ab->qmi.target_mem[1].size == 8454144 Then allocation failed like before and ath12k_qmi_free_target_mem_chunk() is called to free all allocated segments. Note the first segment is skipped because its v.addr is cleared due to allocation failure: chunk->v.addr = dma_alloc_coherent() Also note that this leaks that segment because it has not been freed. While freeing the second segment, a size of 8454144 is passed to dma_free_coherent(). However remember that this segment is allocated at the first time firmware is loaded, before suspend. So its real size is 524288, much smaller than 8454144. As a result kernel found we are freeing some memory which is in use and thus crashed. So one possible fix would be to free those segments during suspend. This works because with them freed, ath12k_qmi_free_target_mem_chunk() does nothing: all segment addresses are NULL so dma_free_coherent() is not called. But note that ath11k has similar logic but never hits this issue. Reviewing code there shows the luck comes from QMI memory reuse logic. So the decision is to port it to ath12k. Like in ath11k, the crash is avoided by adding prev_size to target_mem_chunk structure and caching real segment size in it, then prev_size instead of current size is passed to dma_free_coherent(), no unexpected memory is freed now. Also reuse m3 buffer. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240419034034.2842-1-quic_bqiang@quicinc.com
2024-04-22wifi: ath12k: fix out-of-bound access of qmi_invoke_handler()Karthikeyan Kathirvel
Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence facing below KASAN warning, ================================================================== BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148 Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273 CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0 Workqueue: qmi_msg_handler qmi_data_ready_work Call trace: dump_backtrace+0x0/0x20c show_stack+0x14/0x1c dump_stack+0xe0/0x138 print_address_description.isra.5+0x30/0x330 __kasan_report+0x16c/0x1bc kasan_report+0xc/0x14 __asan_load8+0xa8/0xb0 qmi_invoke_handler+0xa4/0x148 qmi_handle_message+0x18c/0x1bc qmi_data_ready_work+0x4ec/0x528 process_one_work+0x2c0/0x440 worker_thread+0x324/0x4b8 kthread+0x210/0x228 ret_from_fork+0x10/0x18 The address belongs to the variable: ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k] [...] ================================================================== Add a dummy terminator entry at the end to assist the qmi_invoke_handler() in traversing up to the terminator entry without accessing an out-of-boundary index. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240416080234.2882725-1-quic_kathirve@quicinc.com
2024-04-22wifi: ath12k: Refactor data path cmem initKarthikeyan Periyasamy
Move the data path Tx and Rx descriptor primary page table CMEM configuration into a helper function. This will make the code more scalable for configuring partner device in support of multi-device MLO. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-5-quic_periyasa@quicinc.com
2024-04-22wifi: ath12k: displace the Tx and Rx descriptor in cookie conversion tableKarthikeyan Periyasamy
In the hardware cookie conversion table configuration, place the Rx descriptor at the end. This will allow for easier addition of partner device Rx descriptors in the future to support multi-device MLO. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-4-quic_periyasa@quicinc.com
2024-04-22wifi: ath12k: Refactor the hardware cookie conversion initKarthikeyan Periyasamy
Currently, the Rx descriptor is placed before the Tx descriptor in the primary page table of the hardware cookie conversion configuration. The Tx and Rx descriptor offsets are implicitly hardcoded. To allow for easy displacement of Tx and Rx descriptors, introduce Tx and Rx offset based cookie conversion initializationi. Additionally, should consider validating the respective offset ranges while retrieving the Tx and Rx descriptors. This change will be utilize by the next patch in the series. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-3-quic_periyasa@quicinc.com
2024-04-22wifi: ath12k: avoid redundant code in Rx cookie conversion initKarthikeyan Periyasamy
Currently, in the Rx data path cookie conversion initialization procedure, the primary page table index (ppt_idx) is computed within the secondary page table iteration. However this is invariant, and hence the ppt_idx should be calculated outside of the iteration to avoid repeated execution of the statement. Found in code review. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-2-quic_periyasa@quicinc.com
2024-04-18wifi: ath12k: don't use %pK in dmesg format stringsJeff Johnson
Currently, when debug logs are enabled, messages such as the following are found in the kernel log: event mgmt rx skb pK-error len 209 ftype 00 stype 50 The "pK-error" comes from using %pK to display an skb address in an interrupt context. Per the guidance in the current "printk-formats" documentation, %pK "is only intended when producing content of a file read by userspace from e.g. procfs or sysfs, not for dmesg." So replace %pK with %p in all of the ath12k_dbg() format strings. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
2024-04-18wifi: ath12k: enable service flag for survey dump statsThiraviyam Mariyappan
The survey dump statistics does not display channel RX and TX time properly because the survey flag is not enabled in the firmware service flag. If firmware supports enable the service flag "bss_chan_info" in wmi_resource_config to fetch and print the stats for specific pdev. Enabling WMI_RSRC_CFG_FLAG1_BSS_CHANNEL_INFO_64 does not have any impact on WCN7850 since this bit is not utilized by the WCN7850 firmware. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240410085329.3649572-1-quic_kathirve@quicinc.com
2024-04-18wifi: ath12k: enable WIPHY_FLAG_DISABLE_WEXTKalle Valo
ath12k will support Multi-Link Operation (MLO) in the future but not yet. A major change with MLO is that cfg80211 will disable Wireless Extension (WEXT) user space interface. To avoid having inconsistent user experience, first supporting WEXT and later not, disable WEXT already now. Now ath12k claims that WEXT is not supported: $ iwconfig wlan0 wlan0 no wireless extensions. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://msgid.link/20240411165645.4071238-1-kvalo@kernel.org
2024-04-18wifi: ath11k: Fix error handling in ath11k_wmi_p2p_noa_event()Christophe JAILLET
if (noa_descriptors > WMI_P2P_MAX_NOA_DESCRIPTORS), there is a mix of return and goto. In such a case, 'td' should be freed to avoid a memory leak. While at it, change ath11k_wmi_p2p_noa_event() to return void. '0' was returned in all cases, even in case of error and the only caller does not handle the return value. This is also more consistent with most of functions called from ath11k_wmi_tlv_op_rx(). Fixes: 2408379f15a1 ("wifi: ath11k: implement handling of P2P NoA event") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/07f1fc75b2d5b4173ae1b7bb1da5be7f6fc608c8.1713212781.git.christophe.jaillet@wanadoo.fr
generated by cgit v1.2.3-58-ga151 (git 2.39.0) at 2024-11-22 02:06:42 +0000