| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds WMI interface to configure station specific
TID configuration . Host needs to send station's MAC address
along with TID number and its configuration to target through
WMI_10_4_PER_PEER_PER_TID_CONFIG_CMDID.
WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT flag is added to advertise
this support.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-2-git-send-email-tamizhr@codeaurora.org
|
|
Currently when the sending of any management pkt
via wmi command fails, the packet is being unmapped
freed in the error handling. But the idr entry added,
which is used to track these packet is not getting removed.
Hence, during unload, in wmi cleanup, all the entries
in IDR are removed and the corresponding buffer is
attempted to be freed. This can cause a situation where
one packet is attempted to be freed twice.
Fix this error by rmeoving the msdu from the idr
list when the sending of a management packet over
wmi fails.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 1807da49733e ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588667015-25490-1-git-send-email-pillair@codeaurora.org
|
|
For SDIO chip, its rx indication is struct htt_rx_indication_hl, which
does not include the bitrate info as well as PCIe, for PCIe, it use
function ath10k_htt_rx_h_rates to parse the bitrate info in struct
rx_ppdu_start and then report it to mac80211 via ieee80211_rx_status.
SDIO does not have the same info as PCIe, then iw command can not get
the rx bitrate by "iw wlan0 station dump".
for example, it always show 6.0 MBit/s
localhost ~ # iw wlan0 link
Connected to 3c:28:6d:96:fd:69 (on wlan0)
SSID: kukui_test
freq: 5180
RX: 111800 bytes (595 packets)
TX: 35419 bytes (202 packets)
signal: -41 dBm
rx bitrate: 6.0 MBit/s
This patch is to send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware
for ath10k_sta_statistics and save the rx bitrate for WMI event
WMI_TLV_PEER_STATS_INFO_EVENTID.
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, this patch only enable
it for "qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-3-wgong@codeaurora.org
|
|
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662ce1
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662ce1 ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.
This shows up in 'iw phy' as:
WoWLAN support:
* wake up on network detection, up to 16 match sets
And it can be enabled with command:
iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo
Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation
feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag.
This new features enables the ath10k host to send information to the
firmware on the specifications of detected radar type. This allows the
firmware to validate if the host's radar pattern detector unit is
operational and check if the radar information shared by host matches
the radar pulses sent as phy error events from firmware. If the check
fails the firmware won't allow use of DFS channels on AP mode when using
FCC regulatory region.
Hence this patch is mandatory when using a firmware from 10.4-3.6 branch.
Else, DFS channels on FCC regions cannot be used.
Supported Chipsets : QCA9984/QCA9888/QCA4019
Firmware Version : 10.4-3.6-00104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.
Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Update year for Qualcomm Atheros, Inc. copyrights.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
HL1.0 firmware branch, used in wcn3990, transmits management
frames by reference over WMI.
Add support for management tx by reference over WMI.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
WMI ops wrappers did not properly check for null
function pointers for spectral scan. This caused
null dereference crash with WMI-TLV based firmware
which doesn't implement spectral scan.
The crash could be triggered with:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
The crash looked like this:
[ 168.031989] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 168.037406] IP: [< (null)>] (null)
[ 168.040395] PGD cdd4067 PUD fa0f067 PMD 0
[ 168.043303] Oops: 0010 [#1] SMP
[ 168.045377] Modules linked in: ath10k_pci(O) ath10k_core(O) ath mac80211 cfg80211 [last unloaded: cfg80211]
[ 168.051560] CPU: 1 PID: 1380 Comm: bash Tainted: G W O 4.8.0 #78
[ 168.054336] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 168.059183] task: ffff88000c460c00 task.stack: ffff88000d4bc000
[ 168.061736] RIP: 0010:[<0000000000000000>] [< (null)>] (null)
...
[ 168.100620] Call Trace:
[ 168.101910] [<ffffffffa03b9566>] ? ath10k_spectral_scan_config+0x96/0x200 [ath10k_core]
[ 168.104871] [<ffffffff811386e2>] ? filemap_fault+0xb2/0x4a0
[ 168.106696] [<ffffffffa03b97e6>] write_file_spec_scan_ctl+0x116/0x280 [ath10k_core]
[ 168.109618] [<ffffffff812da3a1>] full_proxy_write+0x51/0x80
[ 168.111443] [<ffffffff811957b8>] __vfs_write+0x28/0x120
[ 168.113090] [<ffffffff812f1a2d>] ? security_file_permission+0x3d/0xc0
[ 168.114932] [<ffffffff8109b912>] ? percpu_down_read+0x12/0x60
[ 168.116680] [<ffffffff811965f8>] vfs_write+0xb8/0x1a0
[ 168.118293] [<ffffffff81197966>] SyS_write+0x46/0xa0
[ 168.119912] [<ffffffff818f2972>] entry_SYSCALL_64_fastpath+0x1a/0xa4
[ 168.121737] Code: Bad RIP value.
[ 168.123318] RIP [< (null)>] (null)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add API support for Extended Resource Configuration for 10.4. This
is useful to enable new features like Peer Stats, LTEU etc if the
firmware advertises support for the service. This is also done to
provide backward compatibility with older firmware. Also for clarity
send default host platform type as 'WMI_HOST_PLATFORM_HIGH_PERF',
though this should not make any difference in functionality
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Abstraction layer for vdev subtype is added to solve
subtype mismatch and to give flexible compatibility
among different firmware revisions.
For instance, 10.2 and 10.4 firmware has different
definition of their vdev subtypes for Mesh.
10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5.
Hence use the abstraction API to get right subtype to use.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The patch makes debug stats prints fw specific by adding a new member
in wmi_ops. That way it's easier to add fw_stats support to 10.4 firmware.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh Chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.
Example usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel 5180 mode 10
CTL = 0x10 Reg. Domain = 58
Antenna Gain = 1 Reg. Max Antenna Gain = 0
Power Limit = 34 Reg. Max Power = 34
Num tx chains = 3 Num supported rates = 155
**********CDD POWER TABLE*******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
1 CCk 0x41 0 0 0
[...]
154 HTCUP 0x 0 24 0 0
**********STBC POWER TABLE******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
[...]
154 HTCUP 0x 0 24 24 0
**********TXBF POWER TABLE******
is used to dump the tx power control stats.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This command will be used to configure
multi-channel scheduler in firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
As a part of tdls implementation introduce
tdls related wmi data structures, constant
values and functions.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for WOW patterns.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for WOW like enable,
wakeup events and host wakeup indication.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This can be used to implement offloaded rssi
threshold, beacon miss or even automatic
in-firmware BSS roaming in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The expected parameter is not a single value but a
mask of values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The command logic shouldn't really care about
arvif structure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New wmi-tlv firmware for qca6174 has STA keepalive
service available. The service can provide
automatic idle connection polling via NullFunc
frames to AP when acting as a client.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New wmi-tlv firmware for qca6174 supports this.
This will be used soon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Along beacon template host is expected to setup
p2p information elements as well. Implement wmi
interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions with beacon templates need
probe templates as well because they don't forward
probe requests to host at all.
This is required for new firmware to work with
direct probe requests (notably required by hidden
ssid AP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions may support setting beacon
template. Implement wmi interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending delba request. This command is used for
debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending addba response manually. This command
is used for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending addba request. This command is meant
for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for clearing addba response before switching aggregation
mode (auto/manual) for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
