| Age | Commit message (Collapse) | Author |
|---|
|
This patch is needed because the BASE-T1 uses different registers
for status, control and advertisement to those already
employed in the existing phy-c45 functions.
Where required, genphy_c45 functions will now check whether
the device supports BASE-T1 and use the specific registers
instead: 45.2.7.19 BASE-T1 AN control register,
45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN
advertisement register, 45.2.7.22 BASE-T1 AN LP Base
Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control
register.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_attach_direct() first calls phy_init_hw() (which restores interrupt
settings through ->config_intr()), then calls phy_disable_interrupts().
So if phydev->interrupts was previously set to 1, interrupts are briefly
enabled, then disabled, which seems nonsensical.
If it was previously set to 0, interrupts are disabled twice, which is
equally nonsensical.
Deduplicate interrupt disablement.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/805ccdc606bd8898d59931bd4c7c68537ed6e550.1651040826.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_read_master_slave function allows to configure the master/slave
for gigabit phys only. In order to use this function irrespective of
speed, moved the speed check to the genphy_read_status call.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit bafbdd527d56 ("phylib: Add device reset GPIO support") added call
to phy_device_reset(phydev) after the put_device() call in phy_detach().
The comment before the put_device() call says that the phydev might go
away with put_device().
Fix potential use-after-free by calling phy_device_reset() before
put_device().
Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case a PHY device was probed thus in the PHY_READY state, but not
configured and with no network device attached yet, we should not be
trying to shut it down because it has been brought back into reset by
phy_device_reset() towards the end of phy_probe() and anyway we have not
configured the PHY yet.
Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYLIB device drivers must match by either numerical PHY ID or by their
.match_phy_device method. Matching by DT is not permitted.
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3ac8eed62596387214869319379c1fcba264d8c6, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.
That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.
The stack trace is:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330
Examples why that assumption is not fine:
- There is an MDIO bus with a PHY device that doesn't have a specific
PHY driver loaded, because mdiobus_register() automatically creates a
PHY device for it but there is no specific PHY driver in the system.
Normally under those circumstances, the generic PHY driver will be
bound lazily to it (at phy_attach_direct time). But some Ethernet
drivers attach to their PHY at .ndo_open time. Until then it, the
to-be-driven-by-genphy PHY device will not have a driver. The blamed
patch amounts to saying "you need to open all net devices before the
system can suspend, to avoid the NULL pointer dereference".
- There is any raw MDIO device which has 'plausible' values in the PHY
ID registers 2 and 3, which is located on an MDIO bus whose driver
does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
devices). An example could be a MAC's internal MDIO bus with PCS
devices on it, for serial links such as SGMII. PHY devices will get
created for those PCSes too, due to that MDIO bus auto-scanning, and
although those PHY devices are not used, they do not bother anybody
either. PCS devices are usually managed in Linux as raw MDIO devices.
Nonetheless, they do not have a PHY driver, nor does anybody attempt
to connect to them (because they are not a PHY), and therefore this
patch breaks that.
The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.
For instance:
phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.
If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.
That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.
In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.
Fixes: 3ac8eed62596 ("net: phy: Uniform PHY driver access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914140515.2311548-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct phy_device contains a pointer to the PHY driver and nearly
everywhere this pointer is used to access the PHY driver. Only
mdio_bus_phy_may_suspend() is still using to_phy_driver() instead of the
PHY driver pointer. Uniform PHY driver access by eliminating
to_phy_driver() use in mdio_bus_phy_may_suspend().
Only phy_bus_match() and phy_probe() are still using to_phy_driver(),
because PHY driver pointer is not available there.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_read_status and various other PHY functions support PHY specific
overriding of driver functions by using a PHY specific pointer to the
PHY driver. Add support of PHY specific override to phy_loopback too.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add API to read 802.3-c45 IDs so that C22/C45 mixed device can use
C45 APIs without failing ID checks.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Acked-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following format issues:
1. open brace '{' following function definitions should go to the next
line.
2. braces {} are not necessary for single line statements.
3. else should follow close brace '}'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Callers of unregister_mii_timestamper() currently check for NULL
value of mii_ts before calling it.
Place the NULL check inside unregister_mii_timestamper() and update
the callers accordingly.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract phy_id from compatible string. This will be used by
fwnode_mdiobus_register_phy() to create phy device using the
phy_id.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define fwnode_phy_find_device() to iterate an mdiobus and find the
phy device of the provided phy fwnode. Additionally define
device_phy_find_device() to find phy device of provided device.
Define fwnode_get_phy_node() to get phy_node using named reference.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define fwnode_mdio_find_device() to get a pointer to the
mdio_device from fwnode passed to the function.
Refactor of_mdio_find_device() to use fwnode_mdio_find_device().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY devices such as the Marvell Alaska 88E2110 does not return a valid
PHY ID when probed using Clause-22. The current implementation treats
PHY ID of zero as a non-error and valid PHY ID, and causing the PHY
device failed to bind to the Marvell driver.
For such devices, we do an additional probe in the Clause-45 space,
if a valid PHY ID is returned, we then proceed to attach the PHY
device to the matching PHY ID driver.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate the follow smatch warning:
drivers/net/phy/phy_device.c:2886 phy_probe() warn: inconsistent
indenting.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.
This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The generic loopback is really generic and is defined by the 802.3
standard, we should just mandate that drivers implement a custom
loopback if the generic one cannot work.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resume callback of the PHY driver is called after the one for the MAC
driver. The PHY driver resume callback calls phy_init_hw(), and this is
potentially problematic if the MAC driver calls phy_start() in its resume
callback. One issue was reported with the fec driver and a KSZ8081 PHY
which seems to become unstable if a soft reset is triggered during aneg.
The new flag allows MAC drivers to indicate that they take care of
suspending/resuming the PHY. Then the MAC PM callbacks can handle
any dependency between MAC and PHY PM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phydev::dev_flags contains a bitmask of configuration bits requested by
the consumer of a PHY device (Ethernet MAC or switch) towards the PHY
driver. Since these flags are often used for requesting LED or other
type of configuration being able to quickly audit them without
instrumenting the kernel is useful.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PM_SLEEP is disabled, the compiler warns about unused
functions:
drivers/net/phy/phy_device.c:273:12: error: unused function 'mdio_bus_phy_suspend' [-Werror,-Wunused-function]
static int mdio_bus_phy_suspend(struct device *dev)
drivers/net/phy/phy_device.c:293:12: error: unused function 'mdio_bus_phy_resume' [-Werror,-Wunused-function]
static int mdio_bus_phy_resume(struct device *dev)
The logic is intentional, so just mark these two as __maybe_unused
and remove the incorrect #ifdef.
Fixes: 4c0d2e96ba05 ("net: phy: consider that suspend2ram may cut off PHY power")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210225145748.404410-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
Add a flag and helper function to indicate that a PHY device is part of
an SFP module, which is set on attach. This can be used by PHY drivers
to handle SFP-specific quirks or behavior.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Claudiu reported that on his system S2R cuts off power to the PHY and
after resuming certain PHY settings are lost. The PM folks confirmed
that cutting off power to selected components in S2R is a valid case.
Therefore resuming from S2R, same as from hibernation, has to assume
that the PHY has power-on defaults. As a consequence use the restore
callback also as resume callback.
In addition make sure that the interrupt configuration is restored.
Let's do this in phy_init_hw() and ensure that after this call
actual interrupt configuration is in sync with phydev->interrupts.
Currently, if interrupt was enabled before hibernation, we would
resume with interrupt disabled because that's the power-on default.
This fix applies cleanly only after the commit marked as fixed.
I don't have an affected system, therefore change is compile-tested
only.
[0] https://lore.kernel.org/netdev/1610120754-14331-1-git-send-email-claudiu.beznea@microchip.com/
Fixes: 611d779af7ca ("net: phy: fix MDIO bus PM PHY resuming")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to lockdep_assert_held(_once), similar to what is being done
in other subsystems. One advantage is that there's zero runtime
overhead if lockdep support isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we print the driver name twice in phy_attached_print():
- phy_dev_info() prints it as part of the device info
- and we print it as part of the info string
This is a little bit ugly, it makes the info harder to read,
especially if the driver name is a little bit longer.
Therefore omit the driver name (if set) in the info string.
Example from r8169 that uses phylib:
old: Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver \
[Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
new: Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver \
(mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/8ab72586-f079-41d8-84ee-9f6a5bd97b2a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a first step into making phylib and all PHY drivers to actually
have support for shared IRQs, make the .ack_interrupt() callback
optional.
After all drivers have been moved to implement the generic
interrupt handle, the phy_drv_supports_irq() check will be
changed again to only require the .handle_interrupts() callback.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of a board which uses a shared IRQ we can easily end up with an
IRQ storm after a forced reboot.
For example, a 'reboot -f' will trigger a call to the .shutdown()
callbacks of all devices. Because phylib does not implement that hook,
the PHY is not quiesced, thus it can very well leave its IRQ enabled.
At the next boot, if that IRQ line is found asserted by the first PHY
driver that uses it, but _before_ the driver that is _actually_ keeping
the shared IRQ asserted is probed, the IRQ is not going to be
acknowledged, thus it will keep being fired preventing the boot process
of the kernel to continue. This is even worse when the second PHY driver
is a module.
To fix this, implement the .shutdown() callback and disable the
interrupts if these are used.
Note that we are still susceptible to IRQ storms if the previous kernel
exited with a panic or if the bootloader left the shared IRQ active, but
there is absolutely nothing we can do about these cases.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the micrel phy driver calls phy_init_hw() as a workaround,
the commit 9886a4dbd2aa ("net: phy: call phy_disable_interrupts()
in phy_init_hw()") disables the interrupt unexpectedly. So,
call phy_disable_interrupts() in phy_attach_direct() instead.
Otherwise, the phy cannot link up after the ethernet cable was
disconnected.
Note that other drivers (like at803x.c) also calls phy_init_hw().
So, perhaps, the driver caused a similar issue too.
Fixes: 9886a4dbd2aa ("net: phy: call phy_disable_interrupts() in phy_init_hw()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
A recent commit introduced a late error path in phy_device_create()
which fails to release the device name allocated by dev_set_name().
Fixes: 13d0ab6750b2 ("net: phy: check return code when requesting PHY driver module")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the patch below, the iteration through the available MMDs is
completely short-circuited, and devs_in_pkg remains set to the initial
value of zero.
Due to devs_in_pkg being zero, the rest of get_phy_c45_ids() is
short-circuited too: the following loop never reaches below this point
either (it executes "continue" for every device in package, failing to
retrieve PHY ID for any of them):
/* Now probe Device Identifiers for each device present. */
for (i = 1; i < num_ids; i++) {
if (!(devs_in_pkg & (1 << i)))
continue;
So c45_ids->device_ids remains populated with zeroes. This causes an
Aquantia AQR412 PHY (same as any C45 PHY would, in fact) to be probed by
the Generic PHY driver.
The issue seems to be a case of submitting partially committed work (and
therefore testing something other than was submitted).
The intention of the patch was to delay exiting the loop until one more
condition is reached (the devs_in_pkg read from hardware is either 0, OR
mostly f's). So fix the patch to reflect that.
Tested with traffic on a LS1028A-QDS, the PHY is now probed correctly
using the Aquantia driver. The devs_in_pkg bit field is set to
0xe000009a, and the MMDs that are present have the following IDs:
[ 5.600772] libphy: get_phy_c45_ids: device_ids[1]=0x3a1b662
[ 5.618781] libphy: get_phy_c45_ids: device_ids[3]=0x3a1b662
[ 5.630797] libphy: get_phy_c45_ids: device_ids[4]=0x3a1b662
[ 5.654535] libphy: get_phy_c45_ids: device_ids[7]=0x3a1b662
[ 5.791723] libphy: get_phy_c45_ids: device_ids[29]=0x3a1b662
[ 5.804050] libphy: get_phy_c45_ids: device_ids[30]=0x3a1b662
[ 5.816375] libphy: get_phy_c45_ids: device_ids[31]=0x0
[ 7.690237] mscc_felix 0000:00:00.5: PHY [0.5:00] driver [Aquantia AQR412] (irq=POLL)
[ 7.704739] mscc_felix 0000:00:00.5: PHY [0.5:01] driver [Aquantia AQR412] (irq=POLL)
[ 7.718918] mscc_felix 0000:00:00.5: PHY [0.5:02] driver [Aquantia AQR412] (irq=POLL)
[ 7.733044] mscc_felix 0000:00:00.5: PHY [0.5:03] driver [Aquantia AQR412] (irq=POLL)
Fixes: bba238ed037c ("net: phy: continue searching for C45 MMDs even if first returned ffff:ffff")
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of introduction, in commit bdeced75b13f ("net: dsa: felix:
Add PCS operations for PHYLINK"), support for the Lynx PCS inside Felix
was relying, for USXGMII support, on the fact that get_phy_device() is
able to parse the Lynx PCS "device-in-package" registers for this C45
MDIO device and identify it correctly.
However, this was actually working somewhat by mistake (in the sense
that, even though it was detected, it was detected for the wrong
reasons).
The get_phy_c45_ids() function works by iterating through all MMDs
starting from 1 (MDIO_MMD_PMAPMD) and stops at the first one which
returns a non-zero value in the "device-in-package" register pair,
proceeding to see what that non-zero value is.
For the Felix PCS, the first MMD (1, for the PMA/PMD) returns a non-zero
value of 0xffffffff in the "device-in-package" registers. There is a
code branch which is supposed to treat this case and flag it as wrong,
and normally, this would have caught my attention when adding initial
support for this PCS:
if ((devs_in_pkg & 0x1fffffff) == 0x1fffffff) {
/* If mostly Fs, there is no device there, then let's probe
* MMD 0, as some 10G PHYs have zero Devices In package,
* e.g. Cortina CS4315/CS4340 PHY.
*/
However, this code never actually kicked in, it seems, because this
snippet from get_phy_c45_devs_in_pkg() was basically sabotaging itself,
by returning 0xfffffffe instead of 0xffffffff:
/* Bit 0 doesn't represent a device, it indicates c22 regs presence */
*devices_in_package &= ~BIT(0);
Then the rest of the code just carried on thinking "ok, MMD 1 (PMA/PMD)
says that there are 31 devices in that package, each having a device id
of ffff:ffff, that's perfectly fine, let's go ahead and probe this PHY
device".
But after cleanup commit 320ed3bf9000 ("net: phy: split
devices_in_package"), this got "fixed", and now devs_in_pkg is no longer
0xfffffffe, but 0xffffffff. So now, get_phy_device is returning -ENODEV
for the Lynx PCS, because the semantics have remained mostly unchanged:
the loop stops at the first MMD that returns a non-zero value, and that
is MMD 1.
But the Lynx PCS is simply a clause 37 PCS which implements the required
MAC-side functionality for USXGMII (when operated in C45 mode, which is
where C45 devices-in-package detection is relevant to). Of course it
will fail the PMD/PMA test (MMD 1), since it is not a PHY. But it does
implement detection for MDIO_MMD_PCS (3):
- MDIO_DEVS1=0x008a, MDIO_DEVS2=0x0000,
- MDIO_DEVID1=0x0083, MDIO_DEVID2=0xe400
Let get_phy_c45_ids() continue searching for valid MMDs, and don't
assume that every phy_device has a PMA/PMD MMD implemented.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend ethtool_phy_ops to include the 3 function pointers necessary for
implementing PHY statistics. In a subsequent change we will uninline
those functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Utilize ethtool_set_ethtool_phy_ops to register a suitable set of PHY
ethtool operations in a dynamic fashion such that ethtool will no longer
directy reference PHY library symbols.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This array is not used outside of phy_device.c, so make it static.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid the W=1 warning that symbol 'genphy_c45_driver' was not
declared. Should it be static?
Declare it on the phy header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we only call phy_device_reset() if the PHY driver implements
the probe() callback. This is not mandatory and many drivers (e.g.
realtek) don't need probe() for most devices but still can have reset
GPIOs defined. There's no reason to depend on the presence of probe()
here so pull the reset code out of the if clause.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keeping the headers in alphabetical order is better for readability and
allows to easily see if given header is already included.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper function that will return the index in the array for the
passed in internal delay value. The helper requires the array, size and
delay value.
The helper will then return the index for the exact match or return the
index for the index to the closest smaller value.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
