| Age | Commit message (Collapse) | Author |
|---|
|
While we list the "IRQ status *and acknowledge*" registers as volatile
in the MFD description, they are missing from the writable range array,
so acknowledging any interrupts was met with an -EIO error.
This error propagates up, leading to the whole AXP717 driver failing to
probe, which is fatal to most systems using this PMIC, since most
peripherals refer one of the PMIC voltage rails.
This wasn't noticed on the initial submission, since the interrupt was
completely missing at this point, but the DTs now merged describe the
interrupt, creating the problem.
Add the five registers that hold those bits to the writable array.
This fixes the boot on the Anbernic systems using the AXP717 PMIC.
Fixes: b5bfc8ab2484 ("mfd: axp20x: Add support for AXP717 PMIC")
Reported-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/r/20240613233104.17529-1-andre.przywara@arm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
8a3400x device implements its own reg_read and reg_write,
which only supports I2C bus access. This patch adds support
for SMBus access.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/LV3P220MB12021342F302AADEB6C1601CA0192@LV3P220MB1202.NAMP220.PROD.OUTLOOK.COM
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
In 'struct ssbi, the 'slave' field is unused. Remove it.
Found with cppcheck, unusedStructMember.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/8a76de25cefb533d94dfe35062bbd9a8e72f4bb9.1713971415.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ->init() open codes the functionality of DMI matching code.
Moreover, all DMI quirks are using the same callback and driver_data.
With this in mind, refactor the DMI matching code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240423210706.3709568-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The firmware can only be patched once. The current code checks if the
firmware supports the features required by the driver and then patches
if it does not. This could lead to the device being patched twice if
the device was patched before the driver took control, but with a
firmware that doesn't support the features the driver requires. This
would fail but potentially in unpredictable ways.
The check should actually check the device is at the ROM version, and
patch the device if it is. Then a separate later check should error out
if the devices firmware is still too old to be supported. This will at
least fail in a clean way with a nice error message.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240423102339.2363400-1-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The variable err is being assigned -ENODEV and then err is being
re-assigned the same error value via the error exit label err_mfd.
The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/mfd/timberdale.c:768:3: warning: Value stored to 'err' is
never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240415102632.484411-1-colin.i.king@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: wangkaiyuan <wangkaiyuan@inspur.com>
Link: https://lore.kernel.org/r/20240429024547.27724-1-wangkaiyuan@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The secure update driver does a sanity-check of the image size in
comparison to the size of the staging area in FLASH. Instead of
hard-wiring M10BMC_STAGING_SIZE, move the staging size to the
m10bmc_csr_map structure to make the size assignment more flexible.
Co-developed-by: Russ Weight <russell.h.weight@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Peter Colberg <peter.colberg@intel.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240402184925.1065932-1-peter.colberg@intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Drop unneeded parentheses for clarity and consistency.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20240407112445.503bcbc6@endymion.delvare
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use spi_sync_transfer() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/7af920eb686b719cb7eb39c832e3ad414e0e1e1a.1712258667.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Since the chip can power off the system, add the corresponding
functionality.
Based on https://github.com/kobolabs/Kobo-Reader/raw/master/hw/imx6sll-clara2e/kernel.tar.bz2
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20240402111700.494004-3-andreas@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
scnprintf() never returns negative value, drop the respective dead code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240223195113.880121-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Since platform_device_unregister() is NULL-aware, we don't need
to duplicate this check. Remove it and fold the rest of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240223195113.880121-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use the `PLATFORM_DEVID_NONE` constant instead of hard-coding -1
when creating a platform device.
No functional changes are intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240223195113.880121-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use platform_device_register_full() instead of open coding this
function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240223195113.880121-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of creating driver-specific device attributes with
sysfs_create_group() have device core do this by setting up dev_groups
pointer in the driver structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240223195113.880121-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
There is no need to include and use entire ACPI stack in the driver.
Replace respective pieces by agnostic code. No functional change
indented.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240223195113.880121-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Some devices support MSI interrupts. Let's at least try to use them in
platforms that provide MSI capability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240312165905.1764507-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
'ib-mfd-pinctrl-regulator-6.10' and 'ib-mfd-regulator-6.10' into ibs-for-mfd-merged
|
|
Add functionality of the TPS65224 PMIC to the TPS6594 core driver. This
includes adding IRQ resource, MFD cells, and device initialization for
TPS65224.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Acked-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/0109018f2fdc7df4-b986892b-9dac-4af2-90f5-57fd67ed154d-000000@ap-south-1.amazonses.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for TPS65224 PMIC in TPS6594's SPI driver which has
significant functional overlap.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Acked-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/0109018f2fdc6328-6d13785c-9832-471b-bdfe-fb1dac3bdc60-000000@ap-south-1.amazonses.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for TPS65224 PMIC in TPS6594's I2C driver which has
significant functional overlap.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Acked-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/0109018f2fdaecea-12513236-1059-4227-9078-7b3e0d447cc0-000000@ap-south-1.amazonses.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
In regmap_config use volatile_table instead of volatile_reg. This change
makes it easier to add support for TPS65224 PMIC.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Acked-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/0109018f2f267f6e-3121fa42-4816-45f7-a96d-0d6b4678da5a-000000@ap-south-1.amazonses.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This integrates RK816 support in the this existing rk8xx mfd driver.
This version has unaligned interrupt registers, which requires to define a
separate get_irq_reg callback for the regmap. Apart from that the
integration is straightforward and the existing structures can be used as
is. The initialization sequence has been taken from vendor kernel.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240416161237.2500037-3-knaerzche@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The AXP717a is a PMIC chip produced by X-Powers, it can be connected to
an I2C or RSB bus.
It's a rather complete PMIC, with many regulators, interrupts, an ADC and
battery charging functionality. It also offer USB type-C CC pin
handling.
Describe the regmap and the MFD bits, along with the registers exposed
via I2C or RSB. This covers the regulator, interrupts and power key
devices for now.
Advertise the device using the new compatible string.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Link: https://lore.kernel.org/r/20240310010211.28653-4-andre.przywara@arm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
|
|
Two regs have wrong values in existing fields, change them to match
the datasheet.
Fixes: ace6d1448138 ("mfd: cs42l43: Add support for cs42l43 core driver")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240301101547.2136948-1-mstrozek@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
A few regs have unnecessary values in defaults, change them to match the
datasheet
Fixes: ace6d1448138 ("mfd: cs42l43: Add support for cs42l43 core driver")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240229155616.118457-1-mstrozek@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add MT6357 codec entry in the MFD driver.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240226-audio-i350-v1-13-4fa1cea1667f@baylibre.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The current implementation to retrieve ACPI resources is faulty
and may cause issues that even can lead to non-booting systems.
When adding data from an ACPI device, the resources are already
assigned to the platform device. Therefore there is no need to
retrieve the resource list from ACPI and manually assign it to
the platform device. Also there shouldn't be any BIOS in the wild
anymore, that does not have resources added to the KEMPLD ACPI
data.
In particular this fixes an issue where the retrieval of the
resource list using /proc/ioports is disturbed and does not list
the assigned resource for the kempld device or even no resources
at all.
On some distributions this also leads to problems during system
initialization (e.g. with udev) and causes the system to not
boot at all.
I have reproduced the issue with the following kernel versions:
5.10.209
5.15.148
6.1.25
6.6.17
6.7.5
6.8-rc5
The patch applies to all of those versions and seems to resolve
the issue.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Link: https://lore.kernel.org/r/af8756be81c9062f9543d2e5d9373cf5e7877b1e.camel@kontron.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ChromeOS embedded controller (EC) supports setting the state of
GPIOs when the system is unlocked, and getting the state of GPIOs in all
cases. Check for the feature support by checking for the GPIO feature
and then populate a sub-device for the gpio hardware on the EC.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240219202325.4095816-3-swboyd@chromium.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Fix link error:
ld.bfd: drivers/mfd/twl-core.o: in function `twl_probe':
git/drivers/mfd/twl-core.c:846: undefined reference to `devm_mfd_add_devices'
Cc: <stable@vger.kernel.org>
Fixes: 63416320419e ("mfd: twl-core: Add a clock subdevice for the TWL6032")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240221143021.3542736-1-alexander.sverdlin@siemens.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the mfd_dev_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240219-device_cleanup-mfd-v1-1-e4eef5ed2da8@marliere.net
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Process rise event last, to avoid stuck keys when multiple interrupts
are coalesced. This can happen typically when resuming from suspend
via power key press and holding the power button for a bit too short,
so that RISE an FALL IRQ flags are set before any interrupt routine
has a chance to run.
Input subsystem will interpret it as holding down a power key for
a long time, which leads to unintended initiation of shutdown UI
on some OSes.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217195615.1767907-1-megi@xff.cz
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of only accepting the ti specific properties accept also
the standard property. For uniformity, search in the parent node
for the tag. The code for powering off is also isolated from the
rest in this file. So it is a pure Linux design decision to put it
here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240217082007.3238948-6-andreas@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
If the system-power-controller property is there, enable power off.
Implementation is based on a Linux v3.0 vendor kernel.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240217082007.3238948-3-andreas@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: f36e789a1f8d ("mfd: altera-sysmgr: Add SOCFPGA System Manager")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220115012.471689-4-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb43421 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use the FIELD_GET() helper, instead of defining a custom macro
implementing the same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/ef7d5fc3d867338520392417cdf2b67ba19aecde.1708002264.git.geert+renesas@glider.be
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-19-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-18-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-17-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-16-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-15-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-14-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20240206071314.8721-13-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20240206071314.8721-12-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240206071314.8721-11-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240206071314.8721-10-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240206071314.8721-9-liubo03@inspur.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
