| Age | Commit message (Collapse) | Author |
|---|
|
intel_{alloc,free}_coherent()"
This commit may cause a less than required dma mask to be used for
some allocations, which apparently leads to module load failures for
iwlwifi sometimes.
This reverts commit d657c5c73ca987214a6f9436e435b34fc60f332a.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Fabio Coatti <fabio.coatti@gmail.com>
Tested-by: Fabio Coatti <fabio.coatti@gmail.com>
|
|
dma_direct_{alloc,free}()"
This reverts commit b468620f2a1dfdcfddfd6fa54367b8bcc1b51248.
It turns out that this broke drm on AMD platforms. Quoting Gabriel C:
"I can confirm reverting b468620f2a1dfdcfddfd6fa54367b8bcc1b51248 fixes
that issue for me.
The GPU is working fine with SME enabled.
Now with working GPU :) I can also confirm performance is back to
normal without doing any other workarounds"
Christan König analyzed it partially:
"As far as I analyzed it we now get an -ENOMEM from dma_alloc_attrs()
in drivers/gpu/drm/ttm/ttm_page_alloc_dma.c when IOMMU is enabled"
and Christoph Hellwig responded:
"I think the prime issue is that dma_direct_alloc respects the dma
mask. Which we don't need if actually using the iommu. This would be
mostly harmless exept for the the SEV bit high in the address that
makes the checks fail.
For now I'd say revert this commit for 4.17/4.18-rc and I'll look into
addressing these issues properly"
Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org # v4.17
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Nothing big this time. In particular:
- Debugging code for Tegra-GART
- Improvement in Intel VT-d fault printing to prevent soft-lockups
when on fault storms
- Improvements in AMD IOMMU event reporting
- NUMA aware allocation in io-pgtable code for ARM
- Various other small fixes and cleanups all over the place"
* tag 'iommu-updates-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/io-pgtable-arm: Make allocations NUMA-aware
iommu/amd: Prevent possible null pointer dereference and infinite loop
iommu/amd: Fix grammar of comments
iommu: Clean up the comments for iommu_group_alloc
iommu/vt-d: Remove unnecessary parentheses
iommu/vt-d: Clean up pasid quirk for pre-production devices
iommu/vt-d: Clean up unused variable in find_or_alloc_domain
iommu/vt-d: Fix iotlb psi missing for mappings
iommu/vt-d: Introduce __mapping_notify_one()
iommu: Remove extra NULL check when call strtobool()
iommu/amd: Update logging information for new event type
iommu/amd: Update the PASID information printed to the system log
iommu/tegra: gart: Fix gart_iommu_unmap()
iommu/tegra: gart: Add debugging facility
iommu/io-pgtable-arm: Use for_each_set_bit to simplify code
iommu/qcom: Simplify getting .drvdata
iommu: Remove depends on HAS_DMA in case of platform dependency
iommu/vt-d: Ratelimit each dmar fault printing
|
|
This way we have one central definition of it, and user can select it as
needed. Note that we now also always select it when CONFIG_DMA_API_DEBUG
is select, which fixes some incorrect checks in a few network drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
|
|
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
intel_{alloc,free}_coherent()
Use the dma_direct_*() helpers and clean up the code flow.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20180319103826.12853-9-hch@lst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This cleans up the code a lot by removing duplicate logic.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20180319103826.12853-8-hch@lst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If NO_DMA=y:
warning: (IPMMU_VMSA && ARM_SMMU && ARM_SMMU_V3 && QCOM_IOMMU) selects IOMMU_IO_PGTABLE_LPAE which has unmet direct dependencies (IOMMU_SUPPORT && HAS_DMA && (ARM || ARM64 || COMPILE_TEST && !GENERIC_ATOMIC64))
and
drivers/iommu/io-pgtable-arm.o: In function `__arm_lpae_sync_pte':
io-pgtable-arm.c:(.text+0x206): undefined reference to `bad_dma_ops'
drivers/iommu/io-pgtable-arm.o: In function `__arm_lpae_free_pages':
io-pgtable-arm.c:(.text+0x6a6): undefined reference to `bad_dma_ops'
drivers/iommu/io-pgtable-arm.o: In function `__arm_lpae_alloc_pages':
io-pgtable-arm.c:(.text+0x812): undefined reference to `bad_dma_ops'
io-pgtable-arm.c:(.text+0x81c): undefined reference to `bad_dma_ops'
io-pgtable-arm.c:(.text+0x862): undefined reference to `bad_dma_ops'
drivers/iommu/io-pgtable-arm.o: In function `arm_lpae_run_tests':
io-pgtable-arm.c:(.init.text+0x86): undefined reference to `alloc_io_pgtable_ops'
io-pgtable-arm.c:(.init.text+0x47c): undefined reference to `free_io_pgtable_ops'
drivers/iommu/qcom_iommu.o: In function `qcom_iommu_init_domain':
qcom_iommu.c:(.text+0x1ce): undefined reference to `alloc_io_pgtable_ops'
drivers/iommu/qcom_iommu.o: In function `qcom_iommu_domain_free':
qcom_iommu.c:(.text+0x754): undefined reference to `free_io_pgtable_ops'
QCOM_IOMMU selects IOMMU_IO_PGTABLE_LPAE, which bypasses its dependency
on HAS_DMA. Make QCOM_IOMMU depend on HAS_DMA to fix this.
Fixes: 0ae349a0f33fb040 ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
parisc:allmodconfig, xtensa:allmodconfig, and possibly others generate
the following Kconfig warning.
warning: (IPMMU_VMSA && ARM_SMMU && ARM_SMMU_V3 && QCOM_IOMMU) selects
IOMMU_IO_PGTABLE_LPAE which has unmet direct dependencies (IOMMU_SUPPORT &&
HAS_DMA && (ARM || ARM64 || COMPILE_TEST && !GENERIC_ATOMIC64))
IOMMU_IO_PGTABLE_LPAE depends on (COMPILE_TEST && !GENERIC_ATOMIC64),
so any configuration option selecting it needs to have the same dependencies.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'arm/mediatek', 'arm/tegra', 'arm/qcom', 'arm/smmu', 'ppc/pamu', 'x86/vt-d', 'x86/amd', 's390' and 'core' into next
|
|
An iommu driver for Qualcomm "B" family devices which do implement the
ARM SMMU spec, but not in a way that is compatible with how the arm-smmu
driver is designed. It seems SMMU_SCR1.GASRAE=1 so the global register
space is not accessible. This means it needs to get configuration from
devicetree instead of setting it up dynamically.
In the end, other than register definitions, there is not much code to
share with arm-smmu (other than what has already been refactored out
into the pgtable helpers).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Certain address calculations in the driver make the
assumption that phys_addr_t and dma_addr_t are 64 bit wide.
Force this by depending on CONFIG_PHYS_64BIT to be set.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The driver does not compile when PCI is not selected, so
make it depend on it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since we print the correct warning, an allmodconfig build is no longer
clean but always prints it, which defeats compile-testing:
drivers/iommu/exynos-iommu.c:58:2: error: #warning "revisit driver if we can enable big-endian ptes" [-Werror=cpp]
This replaces the #warning with a dependency, moving warning text into
a comment.
Fixes: 1f59adb1766d ("iommu/exynos: Replace non-existing big-endian Kconfig option")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'arm/core', 'x86/vt-d', 'x86/amd', 's390' and 'core' into next
|
|
The LPAE/ARMv8 page table format relies on the ability to read and write
64-bit page table entries in an atomic fashion. With the move to a lockless
implementation, we also need support for cmpxchg64 to resolve races when
installing table entries concurrently.
Unfortunately, not all architectures support cmpxchg64, so the code can
fail to compiler when building for these architectures using COMPILE_TEST.
Rather than disable COMPILE_TEST altogether, instead check that
GENERIC_ATOMIC64 is not selected, which is a reasonable indication that
the architecture has support for 64-bit cmpxchg.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Neither the ARM page table code enabled by IOMMU_IO_PGTABLE_LPAE
nor the IPMMU_VMSA driver actually depends on ARM_LPAE, so get
rid of the dependency.
Tested with ipmmu-vmsa on r8a7794 ALT and a kernel config using:
# CONFIG_ARM_LPAE is not set
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Introduce an alternative set of iommu_ops suitable for 64-bit ARM
as well as 32-bit ARM when CONFIG_IOMMU_DMA=y. Also adjust the
Kconfig to depend on ARM or IOMMU_DMA. Initialize the device
from ->xlate() when CONFIG_IOMMU_DMA=y.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch makes it possible to compile the rockchip-iommu driver on
ARM64, so that it can be used with 64-bit SoCs equipped with this type
of IOMMU.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
To make vfio support subchannel devices, we need a css driver for
the vfio subchannels. This patch adds a basic vfio-ccw subchannel
driver for this purpose.
To enable VFIO for vfio-ccw, enable S390_CCW_IOMMU config option
and configure VFIO as required.
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170317031743.40128-5-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
The mediatek IOMMU driver enables some drivers that it does not directly
rely on, and that causes a warning for build testing:
warning: (MTK_IOMMU_V1) selects COMMON_CLK_MT2701_VDECSYS which has unmet direct dependencies (COMMON_CLK && COMMON_CLK_MT2701)
warning: (MTK_IOMMU_V1) selects COMMON_CLK_MT2701_IMGSYS which has unmet direct dependencies (COMMON_CLK && COMMON_CLK_MT2701)
warning: (MTK_IOMMU_V1) selects COMMON_CLK_MT2701_MMSYS which has unmet direct dependencies (COMMON_CLK && COMMON_CLK_MT2701)
This removes the select statements.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
With the device <-> stream ID relationship suitably abstracted and
of_xlate() hooked up, the PCI dependency now looks, and is, entirely
arbitrary. Any bus using the of_dma_configure() mechanism will work,
so extend support to the platform and AMBA buses which do just that.
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
'arm/msm', 'arm/rockchip', 'arm/smmu' and 'core' into next
|
|
Include the generic IOVA code to make use of it in the AMD
IOMMU driver too.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that the driver is DT adapted, bus_set_iommu gets called only
when on compatible matching. So the driver should not break multiplatform
builds now. So remove the BROKEN config.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This iommu uses the armv7 short descriptor format. So use the
generic ARMV7S pagetable ops instead of rewriting the same stuff
in the driver.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Mediatek SoC's M4U has two generations of HW architcture. Generation one
uses flat, one layer pagetable, and was shipped with ARM architecture, it
only supports 4K size page mapping. MT2701 SoC uses this generation one
m4u HW. Generation two uses the ARM short-descriptor translation table
format for address translation, and was shipped with ARM64 architecture,
MT8173 uses this generation two m4u HW. All the two generation iommu HW
only have one iommu domain, and all its iommu clients share the same
iova address.
These two generation m4u HW have slit different register groups and
register offset, but most register names are the same. This patch add iommu
support for mediatek SoC mt2701.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'ppc/pamu', 'core' and 'x86/amd' into next
|
|
The statistics are not really used for anything and should
be replaced by generic and per-device statistic counters.
Remove the code for now.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The Freescale PAMU can be enabled on both 32 and 64-bit
Power chips. Commit 477ab7a19ce restricted PAMU to PPC32.
PPC covers both.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'arm/io-pgtable', 'arm/renesas' and 'core' into next
|
|
IOMMU_DMA does indeed depend on scatterlists having a DMA length, but
the NEED_SG_DMA_LENGTH symbol should be selected, not depended upon.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The newly added Mediatek IOMMU driver uses the IOMMU_DMA infrastructure,
but unlike other such drivers, it does not select 'ARM_DMA_USE_IOMMU',
which is a prerequisite, leading to a link error:
warning: (MTK_IOMMU) selects IOMMU_DMA which has unmet direct dependencies (IOMMU_SUPPORT && NEED_SG_DMA_LENGTH)
drivers/iommu/built-in.o: In function `iommu_put_dma_cookie':
mtk_iommu.c:(.text+0x11fe): undefined reference to `put_iova_domain'
drivers/iommu/built-in.o: In function `iommu_dma_init_domain':
mtk_iommu.c:(.text+0x1316): undefined reference to `init_iova_domain'
drivers/iommu/built-in.o: In function `__iommu_dma_unmap':
mtk_iommu.c:(.text+0x1380): undefined reference to `find_iova'
This adds the same select that the other drivers have. On a related
note, I wonder if we should just always select ARM_DMA_USE_IOMMU
whenever any IOMMU driver is enabled. Are there any cases where
we would enable an IOMMU but not use it?
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0df4fabe208d ("iommu/mediatek: Add mt8173 IOMMU driver")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch adds support for mediatek m4u (MultiMedia Memory Management
Unit).
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch adds support for v5 of SYSMMU controller, found in Samsung
Exynos 5433 SoCs. The main difference of v5 is support for 36-bit physical
address space and some changes in register layout and core clocks hanging.
This patch also adds support for ARM64 architecture, which is used by
Exynos 5433 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Add a nearly-complete ARMv7 short descriptor implementation, omitting
only a few legacy and CPU-centric aspects which shouldn't be necessary
for IOMMU API use anyway.
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Tested-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
As of commit 44d88c754e57a6d9 ("ARM: shmobile: Remove legacy SoC code
for R-Mobile A1"), the Renesas IPMMU/IPMMUI driver is no longer used.
In theory it could still be used on SH-Mobile AG5 and R-Mobile A1 SoCs,
but that requires adding DT support to the driver, which is not
planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"This time including:
- A new IOMMU driver for s390 pci devices
- Common dma-ops support based on iommu-api for ARM64. The plan is
to use this as a basis for ARM32 and hopefully other architectures
as well in the future.
- MSI support for ARM-SMMUv3
- Cleanups and dead code removal in the AMD IOMMU driver
- Better RMRR handling for the Intel VT-d driver
- Various other cleanups and small fixes"
* tag 'iommu-updates-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/vt-d: Fix return value check of parse_ioapics_under_ir()
iommu/vt-d: Propagate error-value from ir_parse_ioapic_hpet_scope()
iommu/vt-d: Adjust the return value of the parse_ioapics_under_ir
iommu: Move default domain allocation to iommu_group_get_for_dev()
iommu: Remove is_pci_dev() fall-back from iommu_group_get_for_dev
iommu/arm-smmu: Switch to device_group call-back
iommu/fsl: Convert to device_group call-back
iommu: Add device_group call-back to x86 iommu drivers
iommu: Add generic_device_group() function
iommu: Export and rename iommu_group_get_for_pci_dev()
iommu: Revive device_group iommu-ops call-back
iommu/amd: Remove find_last_devid_on_pci()
iommu/amd: Remove first/last_device handling
iommu/amd: Initialize amd_iommu_last_bdf for DEV_ALL
iommu/amd: Cleanup buffer allocation
iommu/amd: Remove cmd_buf_size and evt_buf_size from struct amd_iommu
iommu/amd: Align DTE flag definitions
iommu/amd: Remove old alias handling code
iommu/amd: Set alias DTE in do_attach/do_detach
iommu/amd: WARN when __[attach|detach]_device are called with irqs enabled
...
|
|
Pull intel iommu updates from David Woodhouse:
"This adds "Shared Virtual Memory" (aka PASID support) for the Intel
IOMMU. This allows devices to do DMA using process address space,
translated through the normal CPU page tables for the relevant mm.
With corresponding support added to the i915 driver, this has been
tested with the graphics device on Skylake. We don't have the
required TLP support in our PCIe root ports for supporting discrete
devices yet, so it's only integrated devices that can do it so far"
* git://git.infradead.org/intel-iommu: (23 commits)
iommu/vt-d: Fix rwxp flags in SVM device fault callback
iommu/vt-d: Expose struct svm_dev_ops without CONFIG_INTEL_IOMMU_SVM
iommu/vt-d: Clean up pasid_enabled() and ecs_enabled() dependencies
iommu/vt-d: Handle Caching Mode implementations of SVM
iommu/vt-d: Fix SVM IOTLB flush handling
iommu/vt-d: Use dev_err(..) in intel_svm_device_to_iommu(..)
iommu/vt-d: fix a loop in prq_event_thread()
iommu/vt-d: Fix IOTLB flushing for global pages
iommu/vt-d: Fix address shifting in page request handler
iommu/vt-d: shift wrapping bug in prq_event_thread()
iommu/vt-d: Fix NULL pointer dereference in page request error case
iommu/vt-d: Implement SVM_FLAG_SUPERVISOR_MODE for kernel access
iommu/vt-d: Implement SVM_FLAG_PRIVATE_PASID to allocate unique PASIDs
iommu/vt-d: Add callback to device driver on page faults
iommu/vt-d: Implement page request handling
iommu/vt-d: Generalise DMAR MSI setup to allow for page request events
iommu/vt-d: Implement deferred invalidate for SVM
iommu/vt-d: Add basic SVM PASID support
iommu/vt-d: Always enable PASID/PRI PCI capabilities before ATS
iommu/vt-d: Add initial support for PASID tables
...
|
|
'x86/amd' into next
Conflicts:
drivers/iommu/amd_iommu_types.h
|
|
Despite being a platform device, the SMMUv3 is capable of signaling
interrupts using MSIs. Hook it into the platform MSI framework and
enjoy faults being reported in a new and exciting way.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[will: tidied up the binding example and reworked most of the code]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Taking inspiration from the existing arch/arm code, break out some
generic functions to interface the DMA-API to the IOMMU-API. This will
do the bulk of the heavy lifting for IOMMU-backed dma-mapping.
Since associating an IOVA allocator with an IOMMU domain is a fairly
common need, rather than introduce yet another private structure just to
do this for ourselves, extend the top-level struct iommu_domain with the
notion. A simple opaque cookie allows reuse by other IOMMU API users
with their various different incompatible allocator types.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This provides basic PASID support for endpoint devices, tested with a
version of the i915 driver.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The behaviour if you enable PASID support after ATS is undefined. So we
have to enable it first, even if we don't know whether we'll need it.
This is safe enough; unless we set up a context that permits it, the device
can't actually *do* anything with it.
Also shift the feature detction to dmar_insert_one_dev_info() as it only
needs to happen once.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add CONFIG_INTEL_IOMMU_SVM, and allocate PASID tables on supported hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few fixes piled up:
- Fix for a suspend/resume issue where PCI probing code overwrote
dev->irq for the MSI irq of the AMD IOMMU.
- Fix for a kernel crash when a 32 bit PCI device was assigned to a
KVM guest.
- Fix for a possible memory leak in the VT-d driver
- A couple of fixes for the ARM-SMMU driver"
* tag 'iommu-fixes-v4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix NULL pointer deref on device detach
iommu/amd: Prevent binding other PCI drivers to IOMMU PCI devices
iommu/vt-d: Fix memory leak in dmar_insert_one_dev_info()
iommu/arm-smmu: Use correct address mask for CMD_TLBI_S2_IPA
iommu/arm-smmu: Ensure IAS is set correctly for AArch32-capable SMMUs
iommu/io-pgtable-arm: Don't use dma_to_phys()
|
|
This adds an IOMMU API implementation for s390 PCI devices.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Pull IOVA fixes from David Woodhouse:
"The main fix here is the first one, fixing the over-allocation of
size-aligned requests. The other patches simply make the existing
IOVA code available to users other than the Intel VT-d driver, with no
functional change.
I concede the latter really *should* have been submitted during the
merge window, but since it's basically risk-free and people are
waiting to build on top of it and it's my fault I didn't get it in, I
(and they) would be grateful if you'd take it"
* git://git.infradead.org/intel-iommu:
iommu: Make the iova library a module
iommu: iova: Export symbols
iommu: iova: Move iova cache management to the iova library
iommu/iova: Avoid over-allocating when size-aligned
|
|
In checking whether DMA addresses differ from physical addresses, using
dma_to_phys() is actually the wrong thing to do, since it may hide any
DMA offset, which is precisely one of the things we are checking for.
Simply casting between the two address types, whilst ugly, is in fact
the appropriate course of action. Further care (and ugliness) is also
necessary in the comparison to avoid truncation if phys_addr_t and
dma_addr_t differ in size.
We can also reject any device with a fixed DMA offset up-front at page
table creation, leaving the allocation-time check for the more subtle
cases like bounce buffering due to an incorrect DMA mask.
Furthermore, we can then fix the hackish KConfig dependency so that
architectures without a dma_to_phys() implementation may still
COMPILE_TEST (or even use!) the code. The true dependency is on the
DMA API, so use the appropriate symbol for that.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: folded in selftest fix from Yong Wu]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
