| Age | Commit message (Collapse) | Author |
|---|
|
The function iio_device_register() was called in mma8452_probe().
But the function iio_device_unregister() was not called after
a call of the function mma8452_set_freefall_mode() failed.
Thus add the missed function call for one error case.
Fixes: 1a965d405fc6 ("drivers:iio:accel:mma8452: added cleanup provision in case of failure.")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We need the staging/iio fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bma150/smb380 are very similar to the bma023 but have a temperature
channel as well.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The bma180 driver is being extended to support the bma150.
Its temperature channel is unsigned so the center_temp naming
no longer makes.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The bma023 chip is similar enough to the bma180 and bma25x that the
same driver can support all of them. The biggest differences are
the lack of a temperature channel and no low power but still working
mode.
The bma150 is a close relative of the bma023, but it does have a
temperature channel so support is not added for it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The bma180 IIO driver is being extended for support for the chips
support by input's bma150 driver (bma023, bma150, smb380). Don't
allow both drivers to be enabled simultaneously as they're for the
same hardware.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some variants of the bma180 (eg bma023) have different reset
values. In preparation for adding support for them, factor
out the reset value into the chip specific data.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This looks really unusual to have a 'get_device()' hidden in a 'dev_err()'
call.
Remove it.
While at it add a missing \n at the end of the message.
Fixes: 574fb258d636 ("Staging: IIO: VTI sca3000 series accelerometer driver (spi)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The main intent here is to get rid of the iio_buffer_set_attrs() helper, or
at least rework it's usage a bit.
The problem with that helper is that it needs a pointer to the buffer,
which makes supporting multiple buffers per IIO device a bit more
cumbersome.
The hid_sensor_setup_trigger() is pretty much used in the same way:
- iio_triggered_buffer_setup() gets called before
- then hid_sensor_setup_trigger() and hid_sensor_setup_batch_mode() gets
called which may attach some fifo attributes
This change merges the 2 together under the hid_sensor_setup_trigger()
function. Only the &iio_pollfunc_store_time is passed to all devices, so
it's not even required to pass it explicitly outside of the common
hid_sensor_setup_trigger() function.
Moving the devm_iio_triggered_buffer_setup/cleanup() calls into the common
place code can help the rework of the buffer code, since it is in one
place.
One detail of the change is that there are 2 drivers that use
devm_iio_triggered_buffer_setup(). That function gets implicitly
replaced with iio_triggered_buffer_setup()/cleanup(), but since all drivers
call both hid_sensor_setup_trigger9) & hid_sensor_remove_trigger() trigger,
the iio_triggered_buffer_cleanup() piggy backs on the
hid_sensor_remove_trigger() call, which should cover the cleanup.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Enables ACPI DSDT to probe via PRP0001 and the compatible property. Also
removes the ifdef protections for CONFIG_OF.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Enables ACPI DSDT to probe via PRP0001 and the compatible property.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
|
|
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
Add support for STMicroelectronics LISHH12 accelerometer in st_accel
framework.
https://www.st.com/resource/en/datasheet/lis2hh12.pdf
Signed-off-by: Gaëtan André <rvlander@gaetanandre.eu>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
cros-usbpd-notify and cros_ec_typec:
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
CrOS EC:
- Introduce a new cros_ec_cmd_xfer_status helper
Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
Wilco EC:
- Fix a build warning.
- Platform data shouldn't include kernel.h
Misc:
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in
cros_ec_chardev and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
* tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (34 commits)
platform/chrome: cros_ec_spi: Wait for USECS, not NSECS
iio: cros_ec: Use Hertz as unit for sampling frequency
iio: cros_ec: Report hwfifo_watermark_max
iio: cros_ec: Expose hwfifo_timeout
iio: cros_ec: Remove pm function
iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO
iio: expose iio_device_set_clock
iio: cros_ec: Move function description to .c file
platform/chrome: cros_ec_sensorhub: Add median filter
platform/chrome: cros_ec_sensorhub: Add code to spread timestmap
platform/chrome: cros_ec_sensorhub: Add FIFO support
platform/chrome: cros_ec_sensorhub: Add the number of sensors in sensorhub
platform/chrome: chromeos_laptop: make I2C API conversion complete
platform/chrome: wilco_ec: event: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_chardev: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_typec: Update port info from EC
platform/chrome: Add Type C connector class driver
platform/chrome: cros_usbpd_notify: Pull PD_HOST_EVENT status
platform/chrome: cros_usbpd_notify: Amend ACPI driver to plat
platform/chrome: cros_usbpd_notify: Add driver data struct
...
|
|
When EC supports FIFO, each IIO device registers a callback, to put
samples in the buffer when they arrives from the FIFO.
When no FIFO, the user space app needs to call trigger_new, or better
register a high precision timer.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
We need the staging/iio fixes in here as well
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In few places the unnecessary explicit castings are being used.
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use dev_get_platdata() to get the platform_data instead of
referencing it directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 5.6 cycle.
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
* tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ping: set pa_laser_ping_cfg in of_ping_match
iio: chemical: sps30: fix missing triggered buffer dependency
iio: st_sensors: remap SMO8840 to LIS2DH12
iio: light: vcnl4000: update sampling periods for vcnl4040
iio: light: vcnl4000: update sampling periods for vcnl4200
iio: accel: adxl372: Set iio_chan BE
iio: magnetometer: ak8974: Fix negative raw values in sysfs
iio: trigger: stm32-timer: disable master mode when stopping
iio: adc: stm32-dfsdm: fix sleep in atomic context
iio: adc: at91-sama5d2_adc: fix differential channels in triggered mode
|
|
This patch adds a dedicated self_test_reg variable. This is also a step
to let new drivers make use of `adis_initial_startup()`. Some devices
use MSG_CTRL reg to request a self_test command while others use the
GLOB_CMD register.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
According to ST, the HID is for LIS2DH12.
Fixes: 3d56e19815b3 ("iio: accel: st_accel: Add support for the SMO8840 ACPI id")
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Data stored in the iio-buffer is BE and this
should be specified in the iio_chan_spec struct.
Fixes: f4f55ce38e5f8 ("iio:adxl372: Add FIFO and interrupts support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use st_sensors_dev_name_probe() instead open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
|
|
Hardware could be physically mounted in any possible direction and
userpspace needs to be aware of the mounting orientation in order to
process sensor's data correctly. In particular this helps iio-sensor-proxy
to report display's orientation properly on a phone/tablet devices.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This puts an upper bound on "val2" but it also needs to have a lower
bound (BMA400_SCALE_MIN).
Fixes: 465c811f1f20 ("iio: accel: Add driver for the BMA400")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since we have access to the struct device_driver and thus to the ID table,
there is no need to supply special parameters to st_sensors_of_name_probe().
Besides that we have a common API to get driver match data, there is
no need to do matching separately for OF and ACPI.
Taking into consideration above, simplify the ST sensors code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
All timeouts are now handled by a dedicated timeout struct. This
variable is no longer needed.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The adis library only allows to define a `startup_delay` which for some
devices is enough. However, other devices define different timeouts with
significantly different timings which could lead to devices to not wait
enough time or to wait a lot more than necessary (which is not
efficient). This patch introduces a new timeout struct that must be
passed into `adis_init()`. There are mainly, for now, three timeouts
used. This is also an introductory patch with the goal of refactoring
`adis_initial_startup()`. New driver's (eg: adis16480, adis16460) are
replicating code for the device initial setup. With some changes (being
this the first one) we can pass this to `adis_initial_startup()`.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
|
|
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
This adds support for the BMA254 variant of this
accelerometer. The only difference for the simple IIO
driver is that values are 12 bit and the temperature
offset differs by 1 degree.
Whilst wildcards in naming are normally frowned upon:
The cases where I have labeled variables "25x" is where the
models are identical, so as to make things easier for people
that want to add support for BMA253 and BMA255.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This uses the C99 explicit .member assignment for the
variant data in struct bma180_part_info. This makes it
easier to understand and add new variants.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This brings up the VDD and VDDIO regulators using the
regulator framework. Platforms that do not use regulators
will provide stubs or dummy regulators.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Having a shorthand "dev" instead of &client->dev everywhere
makes the code easier to read (more compact).
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark default_accel_pdata with __maybe_unused to calm a compiler down:
In file included from drivers/iio/accel/st_accel_i2c.c:19:
drivers/iio/accel/st_accel.h:67:46: warning: ‘default_accel_pdata’ defined but not used [-Wunused-const-variable=]
67 | static const struct st_sensors_platform_data default_accel_pdata = {
| ^~~~~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ACPI_PTR() takes care of the argument in case of !CONFIG_ACPI.
Remove unnecessary #else branch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for the VDD and VDDIO regulators using the regulator
framework.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add a IIO driver for the Bosch BMA400 3-axes ultra-low power accelerometer.
The driver supports reading from the acceleration and temperature
registers. The driver also supports reading and configuring the output data
rate, oversampling ratio, and scale.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.5 cycle.
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
iio: adc: max1027: fix not unregistered iio trigger
iio: adc: intel_mrfld_adc: Allocating too much data in probe()
iio: adc: ad7124: Enable internal reference
dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
dt-bindings: iio: adc: ad7292: Update SPDX identifier
iio: temperature: ltc2983: fix u32 read into a unsigned long long
iio: st_accel: Fix unused variable warning
iio: adc: ad7606: fix reading unnecessary data from device
|
|
drivers/iio/accel/st_accel_core.c:1005:44: warning:
mount_matrix_ext_info defined but not used [-Wunused-const-variable=]
Using stub helper while CONFIG_ACPI is disabled to fix it.
Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
|
|
Remove the duplicated code in MFD, since MFD just registers cros-ec-sensorhub
if at least one sensor is present.
Change IIO cros-ec driver to get the pointer to the cros-ec-dev through
cros-ec-sensorhub.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
None of the ST sensor drivers use any symbols from
<linux/gpio.h>, just drop the include from all of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
|
|
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
