| Age | Commit message (Collapse) | Author |
|---|
|
Device tree already has a mechanism to pass the wake_irq. It does this
by looking for the wakeup-source property and setting the
I2C_CLIENT_WAKE flag. This CL adds the ACPI equivalent. It uses the
ACPI interrupt wake flag to determine if the interrupt can be used to
wake the system. Previously the i2c drivers had to make assumptions and
blindly enable the wake IRQ. This can cause spurious wake events. e.g.,
If there is a device with an Active Low interrupt and the device gets
powered off while suspending, the interrupt line will go low since it's
no longer powered and wakes the system. For this reason we should
respect the board designers wishes and honor the wake bit defined on the
interrupt.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
i2c_setup_smbus_alert() is only needed within the I2C core, so no need
to expose it to other modules.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We have no users of i2c_acpi_match_device() anymore and seems
will not have them in the future, thus remove dead code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Atomic transfers are not only about sending messages like the original
wording suggested. Speak of 'accessing' now like in i2c.h.
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"New stuff from the I2C world:
- in the core, getting irqs from ACPI is now similar to OF
- new driver for MediaTek MT7621/7628/7688 SoCs
- bcm2835, i801, and tegra drivers got some more attention
- GPIO API cleanups
- cleanups in the core headers
- lots of usual driver updates"
* 'i2c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (74 commits)
i2c: mt7621: Fix platform_no_drv_owner.cocci warnings
i2c: cpm: remove casting dma_alloc
dt-bindings: i2c: sun6i-p2wi: Fix the binding example
dt-bindings: i2c: mv64xxx: Fix the example compatible
i2c: i801: Documentation update
i2c: i801: Add support for Intel Tiger Lake
i2c: i801: Fix PCI ID sorting
dt-bindings: i2c-stm32: document optional dmas
i2c: i2c-stm32f7: Add I2C_SMBUS_I2C_BLOCK_DATA support
i2c: core: Tidy up handling of init_irq
i2c: core: Move ACPI gpio IRQ handling into i2c_acpi_get_irq
i2c: core: Move ACPI IRQ handling to probe time
i2c: acpi: Factor out getting the IRQ from ACPI
i2c: acpi: Use available IRQ helper functions
i2c: core: Allow whole core to use i2c_dev_irq_from_resources
eeprom: at24: modify a comment referring to platform data
dt-bindings: i2c: omap: Add new compatible for J721E SoCs
dt-bindings: i2c: mv64xxx: Add YAML schemas
dt-bindings: i2c: sun6i-p2wi: Add YAML schemas
i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver
...
|
|
Bring the ACPI path in sync with the device tree path and handle all the
IRQ fetching at probe time. This leaves the only IRQ handling at device
registration time being that which is passed directly through the board
info as either a resource or an actual IRQ number.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Remove the static from i2c_dev_irq_from _resources so that other parts
of the core code can use this helper function.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We checked I2C calls, but not SMBus. Refactor the helper to an inline
function and use it for both, I2C and SMBus.
Fixes: 9ac6cb5fbb17 ("i2c: add suspended flag and accessors for i2c adapters")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We had the request to access devices very late when interrupts are not
available anymore multiple times now. Mostly to prepare shutdown or
reboot. Allow adapters to specify a specific callback for this case.
Note that we fall back to the generic {master|smbus}_xfer callback if
this new atomic one is not present. This is intentional to preserve the
previous behaviour and avoid regressions. Because there are drivers not
using interrupts or because it might have worked "accidently" before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If I2C transfers are executed in atomic contexts, trylock is used
instead of lock. This behaviour was missing for SMBUS, although a lot of
transfers are of SMBUS type, either emulated or direct. So, factor out
the locking routine into a helper and use it for I2C and SMBUS.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit cea443a81c9c ("i2c: Support i2c_transfer in atomic contexts")
added in_atomic() to the I2C core. However, the use of in_atomic()
outside of core kernel code is discouraged and was already[1] when this
code was added in early 2008. The above commit was a preparation for
commit b7a3670131c7 ("i2c-pxa: Add polling transfer"). Its commit
message says explicitly it was added "for cases where I2C transactions
have to occur at times interrup[t]s are disabled". So, the intention was
'disabled interrupts'. This matches the use cases for atomic I2C
transfers I have seen so far: very late communication (mostly to a PMIC)
to powerdown or reboot the system. For those cases, interrupts are
disabled then. It doesn't seem that in_atomic() adds value.
After a discussion with Peter Zijlstra[2], we came up with a better set
of conditionals to match the use case.
The I2C core will soon gain an extra callback into bus drivers
especially for atomic transfers to make them more generic. The code
deciding which transfer to use (atomic/non-atomic) should mimic the
behaviour which locking to use (trylock/lock). This is why we add a
helper for it.
[1] https://lwn.net/Articles/274695/
[2] http://patchwork.ozlabs.org/patch/1067437/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
After previous refactoring, there is only one user in the same file
left. Make the function static now.
[wsa: added 'int' to bare 'unsigned']
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
For now empty ID table is not allowed with ACPI and prevents driver to
be probed.
Add a check to allow empty ID table.
This introduces a helper i2c_acpi_match_device().
Note, we rename some static function in i2c-core-acpi.c to distinguish
with public API.
Fixes: da10c06a044b ("i2c: Make I2C ID tables non-mandatory for DT'ed devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Rajmohan Mani <rajmohan.mani@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: needed to get some drivers probed again]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Removes some ifdeffery. Also add the new file to the relevant
MAINTAINERS section.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Also removes some ifdeffery.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Also removes some ifdeffery.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We have a central copy of the GPL for that. Some addresses were already
outdated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
By using rwsem we can easily manage recursive calls of
i2c_scan_static_board_info() function without breaking the locking.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This provides partial support for new-style I2C driver binding. It builds
on "struct i2c_board_info" declarations that identify I2C devices on a given
board. This is needed on systems with I2C devices that can't be fully probed
and/or autoconfigured, such as many embedded Linux configurations where the
way a given I2C device is wired may affect how it must be used.
There are two models for declaring such devices:
* LATE -- using a public function i2c_new_device(). This lets modules
declare I2C devices found *AFTER* a given I2C adapter becomes available.
For example, a PCI card could create adapters giving access to utility
chips on that card, and this would be used to associate those chips with
those adapters.
* EARLY -- from arch_initcall() level code, using a non-exported function
i2c_register_board_info(). This copies the declarations *BEFORE* such
an i2c_adapter becomes available, arranging that i2c_new_device() will
be called later when i2c-core registers the relevant i2c_adapter.
For example, arch/.../.../board-*.c files would declare the I2C devices
along with their platform data, and I2C devices would behave much like
PNPACPI devices. (That is, both enumerate from board-specific tables.)
To match the exported i2c_new_device(), the previously-private function
i2c_unregister_device() is now exported.
Pending later patches using these new APIs, this is effectively a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
