| Age | Commit message (Collapse) | Author |
|---|
|
driver
ADM1177 is a Hot Swap Controller and Digital Power Monitor with
Soft Start Pin.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Link: https://lore.kernel.org/r/20200114112159.25998-1-beniamin.bia@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:
$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1: +23.0°C
or directly from sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0°C (low = +0.0°C, high = +60.0°C)
(crit low = -41.0°C, crit = +85.0°C)
(lowest = +23.0°C, highest = +34.0°C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.
Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX31730 is a 3-Channel Remote Temperature Sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TI's TMP512/513 are I2C/SMBus system monitor chips. These chips
monitor the supply voltage, supply current, power consumption
and provide one local and up to three (TMP513) remote temperature sensors.
It has been tested using a TI TMP513 development kit (TMP513EVM)
Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Link: https://lore.kernel.org/r/20191112223001.20844-3-etremblay@distech-controls.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ltc2947 is a high precision power and energy monitor with an
internal sense resistor supporting up to +/- 30A. Three internal no
Latency ADCs ensure accurate measurement of voltage and current, while
high-bandwidth analog multiplication of voltage and current provides
accurate power measurement in a wide range of applications. Internal or
external clocking options enable precise charge and energy measurements.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021154115.319073-1-nuno.sa@analog.com
[groeck: Removed unnecessary checks when reading temperature and energy;
PAGE{0,1} -> LTC2947_PAGE_{0,1}]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
|
|
Add a new driver for Synaptics AS370 PVT sensors. Currently, only
temperature is supported.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190827113259.4fb64a17@xhacker.debian
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The JZ4740 boards now use the iio-hwmon driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform.
This driver adds support for the hardware monitoring features of
the Lochnagar 2 to the hwmon API. Monitoring is provided for
the board voltages, currents and temperature supported by the
board controller chip.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.
This driver provides a hwmon interface to the OCC from a service
processor (e.g. a BMC). The driver supports both POWER8 and POWER9 OCCs.
Communications with the POWER8 OCC are established over standard I2C
bus. The driver communicates with the POWER9 OCC through the FSI-based
OCC driver, which handles the lower-level communication details.
This patch lays out the structure of the OCC hwmon driver. There are two
platform drivers, one each for P8 and P9 OCCs. These are probed through
the I2C tree and the FSI-based OCC driver, respectively. The patch also
defines the first common structures and methods between the two OCC
versions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
[groeck: Fix up SPDX license identifier]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
|
|
Currently there is no easy way to detect undervoltage conditions on a
remote Raspberry Pi. This hwmon driver retrieves the state of the
undervoltage sensor via mailbox interface. The handling based on
Noralf's modifications to the downstream firmware driver. In case of
an undervoltage condition only an entry is written to the kernel log.
CC: "Noralf Trønnes" <noralf@tronnes.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add Nuvoton BMC NPCM750/730/715/705 Pulse Width Modulation (PWM)
and Fan tacho driver.
The Nuvoton BMC NPCM750/730/715/705 supports 8 PWM controller outputs
and 16 Fan controller inputs.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value from 0(off) and 255(full speed)
and read the fan tacho rpm value.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Driver obtains PWM and tachometers registers location according to the
system configuration and creates FAN/PWM hwmon objects and a cooling
device. PWM and tachometers are controlled through the on-board
programmable device, which exports its register map. This device could be
attached to any bus type, for which register mapping is supported. Single
instance is created with one PWM control, up to 12 tachometers and one
cooling device. It could be as many instances as programmable device
supports.
Currently driver will be activated from the Mellanox platform driver:
drivers/platform/x86/mlx-platform.c.
For the future ARM based systems it could be activated from the ARM
platform module.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Management Interface
(SCMI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Nuvoton W83773G is a hardware monitor IC providing one local
temperature and two remote temperature sensors.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- drivers for MAX31785 and MAX6621
- support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- various driver cleanups and minor improvements
* tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (30 commits)
dt-bindings: pmbus: Add Maxim MAX31785 documentation
pmbus: Add driver for Maxim MAX31785 Intelligent Fan Controller
hwmon: (aspeed-pwm-tacho) Sort headers
hwmon: (xgene) Minor clean up of ifdef and acpi_match_table reference
hwmon: (max6621) Inverted if condition in max6621_read()
hwmon: (asc7621) remove redundant assignment to newval
hwmon: (xgene) Support hwmon v2
hwmon: (gpio-fan) Fix null pointer dereference at probe
hwmon: (gpio-fan) Convert to use GPIO descriptors
hwmon: (gpio-fan) Rename GPIO line state variables
hwmon: (gpio-fan) Get rid of the gpio alarm struct
hwmon: (gpio-fan) Get rid of platform data struct
hwmon: (gpio-fan) Mandate OF_GPIO and cut pdata path
hwmon: (gpio-fan) Send around device pointer
hwmon: (gpio-fan) Localize platform data
hwmon: (gpio-fan) Use local variable pointers
hwmon: (gpio-fan) Move DT bindings to the right place
Documentation: devicetree: add max6621 device
hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
hwmon: (w83793) make const array watchdog_minors static, reduces object code size
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MAX6621 is a PECI-to-I2C translator provides an efficient, low-cost
solution for PECI-to-SMBus/I2C protocol conversion. It allows reading the
temperature from the PECI-compliant host directly from up to four
PECI-enabled CPUs.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver is no longer needed:
* It has no mainline users
* It has no DT support and OMAP is DT only
* iio-hwmon can be used for madc, which also works with DT
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds a HWMON driver for ST Microelectronics STTS751
temperature sensors.
Thanks-to: LABBE Corentin [for suggestions]
Thanks-to: Guenter Roeck [for suggestion and discussions]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Cc: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the TI TMP108 temperature sensor with some device
configuration parameters.
Signed-off-by: John Muir <john@jmuir.com>
[groeck: Initialize of_match_table]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the tc654 and tc655 fan controllers from Microchip.
http://ww1.microchip.com/downloads/en/DeviceDoc/20001734C.pdf
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed continuation line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds hardware temperature and power reading support for
APM X-Gene SoC using the mailbox communication interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver implements hardware monitoring and watchdog support
for the FTS BMC Chip "Teutates".
Signed-off-by: Thilo Cestonaro <thilo@cestona.ro>
[groeck: Updated subject and description; fixed dependencies]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the the INA3221 26v capable, Triple channel,
Bi-Directional, Zero-Drift, Low-/High-Side, Current/Voltage Monitor
with I2C interface.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver implements support for the Sensirion SHT3x-DIS chip,
a humidity and temperature sensor. Temperature is measured
in degrees celsius, relative humidity is expressed as a percentage.
In the sysfs interface, all values are scaled by 1000,
i.e. the value for 31.5 degrees celsius is 31500.
Signed-off-by: Pascal Sachs <pascal.sachs@sensirion.com>
[groeck: Fixed 'Variable length array is used' gcc warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add basic support for the Maxim Integrated MAX31722/MAX31723 SPI
temperature sensors / thermostats.
Includes:
- ACPI support;
- raw temperature readings;
- power management
Datasheet:
https://datasheets.maximintegrated.com/en/ds/MAX31722-MAX31723.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Create a driver to support the hardware monitoring chip present in
the Zyxel NSA320 and some of the other Zyxel NAS devices.
The driver reads fan speed and temperature from a suitably
pre-programmed MCU on the device.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
[groeck: Dropped .owner field initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This adds support for the Linear Technology LTC2990 I2C System Monitor.
The LTC2990 supports a combination of voltage, current and temperature
monitoring. This driver currently only supports reading two currents
by measuring two differential voltages across series resistors, in
addition to the Vcc supply voltage and internal temperature.
This is sufficient to support the Topic Miami SOM which uses this chip
to monitor the currents flowing into the FPGA and the CPU parts.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The vexpress hwmon implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in regulators.
This patch renames the vexpress hwmon implementation to vexpress-hwmon
so that there will be no clash in the module namespace.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
HTU21 is now supported by IIO, and can be instantiated as hwmon driver
using the iio-hwmon bridge. An explicit hwmon driver is no longer needed.
Cc: William Markezana <william.markezana@meas-spec.com>
Cc: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
|
|
The driver supports the Maxim MAX31790.
Signed-off-by: Il Han <corone.il.han@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
|
|
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch splits CONFIG_I8K compile option to SENSORS_DELL_SMM and CONFIG_I8K.
Option SENSORS_DELL_SMM is now used to enable compilation of dell-smm-hwmon
driver and old CONFIG_I8K option to enable /proc/i8k interface in driver.
So this change allows to compile dell-smm-hwmon driver without legacy /proc/i8k
interface which is needed only for old Dell Inspirion models or for userspace
i8kutils package.
For backward compatibility when CONFIG_I8K is enabled then also SENSORS_DELL_SMM
is enabled and so driver dell-smm-hwmon (with /proc/i8k) is compiled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit moves i8k driver to hwmon tree under name dell-smm-hwmon which is
better name then abbreviation i8k. For backward compatibility is added macro
MODULE_ALIAS("i8k") so modprobe will load driver also old name i8k. CONFIG_I8K
compile option was not changed.
This commit also adds me as maintainer of this new dell-smm-hwmon driver and
remove Guenter Roeck from list who is implicit maintainer all hwmon drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.
Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
NCT7802Y is an I2C based hardware monitoring chip from Nuvoton.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
temperature
This patch adds basic kernel support for reading power values, fan
speed rpm, voltage and temperature data on powernv platforms which
will be exported to user space through sysfs interface.
Test results:
-------------
[root@tul163p1 ~]# sensors
ibmpowernv-isa-0000
Adapter: ISA adapter
fan1: 5465 RPM (min = 0 RPM)
fan2: 5152 RPM (min = 0 RPM)
fan3: 5521 RPM (min = 0 RPM)
fan4: 4891 RPM (min = 0 RPM)
fan5: 0 RPM (min = 0 RPM)
fan6: 0 RPM (min = 0 RPM)
fan7: 7480 RPM (min = 0 RPM)
fan8: 7944 RPM (min = 0 RPM)
temp1: +39.0°C (high = +0.0°C)
power1: 190.00 W
[root@tul163p1 ~]# ls /sys/devices/platform/
alarmtimer ibmpowernv.0 power rtc-generic serial8250 uevent
[root@tul163p1 ~]# ls /sys/devices/platform/ibmpowernv.0/hwmon/hwmon0/
device fan2_min fan4_min fan6_min fan8_min power
fan1_fault fan3_fault fan5_fault fan7_fault in1_fault power1_input
fan1_input fan3_input fan5_input fan7_input in2_fault subsystem
fan1_min fan3_min fan5_min fan7_min in3_fault temp1_input
fan2_fault fan4_fault fan6_fault fan8_fault in4_fault temp1_max
fan2_input fan4_input fan6_input fan8_input name uevent
[root@tul163p1 ~]# ls /sys/class/hwmon/hwmon0/
device fan2_min fan4_min fan6_min fan8_min power
fan1_fault fan3_fault fan5_fault fan7_fault in1_fault power1_input
fan1_input fan3_input fan5_input fan7_input in2_fault subsystem
fan1_min fan3_min fan5_min fan7_min in3_fault temp1_input
fan2_fault fan4_fault fan6_fault fan8_fault in4_fault temp1_max
fan2_input fan4_input fan6_input fan8_input name uevent
[root@tul163p1 ~]#
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds support for Lattice's POWR1220 power manager IC. Read
access to all the ADCs on the chip are supported through the hwmon
sysfs files.
Signed-off-by: Scott Kanowitz <skanowitz@echo360.com>
[Guenter Roeck: Removed some extra ( )]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
