| Age | Commit message (Collapse) | Author |
|---|
|
Realtek MIPS SoCs (platform name Otto) have GPIO controllers with up to
64 GPIOs, divided over two banks. Each bank has a set of registers for
32 GPIOs, with support for edge-triggered interrupts.
Each GPIO bank consists of four 8-bit GPIO ports (ABCD and EFGH). Most
registers pack one bit per GPIO, except for the IMR register, which
packs two bits per GPIO (AB-CD).
Although the byte order is currently assumed to have port A..D at offset
0x0..0x3, this has been observed to be reversed on other, Lexra-based,
SoCs (e.g. RTL8196E/97D/97F).
Interrupt support is disabled for the fallback devicetree-compatible
'realtek,otto-gpio'. This allows for quick support of GPIO banks in
which the byte order would be unknown. In this case, the port ordering
in the IMR registers may not match the reversed order in the other
registers (DCBA, and BA-DC or DC-BA).
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Support GPO(s) found from ROHM BD71815 power management IC. The IC has two
GPO pins but only one is properly documented in the data-sheet. The driver
exposes by default only the documented GPO. The second GPO is connected to
E5 pin and is marked as GND in the data-sheet. Control for this
undocumented pin can be enabled using a special DT property.
This driver is derived from work by Peter Yang <yanglsh@embest-tech.com>
although not so much of the original is left.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Adds interrupt support to the Xilinx GPIO driver so that rising and
falling edge line events can be supported. Since interrupt support is
an optional feature in the Xilinx IP, the driver continues to support
devices which have no interrupt provided.
Depends on OF_GPIO framework for of_xlate function to translate
gpiospec to the GPIO number and flags.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc130 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Moreover this code duplicates gpio-pxa since the IP has been derived
from XScale implementation. If anybody wants to resurrect this
it has to be part of gpio-pxa.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc130 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Support building driver as a loadable kernel module. This allows to
reduce size of a kernel zImage, which is important for some devices
since size of kernel partition may be limited and since some bootloader
variants have known problems in regards to the initrd placement if kernel
image is too big.
$ lsmod
Module Size Used by
gpio_tegra 16384 27
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
gpio-mockup doesn't require SYSFS to be selected so drop that bit from
the Kconfig text.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add the GPIO driver for Toshiba Visconti ARM SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The gpio-rcar driver also supports RZ/G SoC's, update the description to
reflect this.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of GPIO_MXS to ARCH_MXS,
and ask the user in case of compile-testing.
Fixes: 6876ca311bfca5d7 ("gpio: mxs: add COMPILE_TEST support for GPIO_MXS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Commit efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip") moved the
Tegra GPIO driver to the generic GPIO IRQ chip infrastructure and made
the IRQ domain hierarchical, so the driver needs to pull in the support
infrastructure via the GPIOLIB_IRQCHIP and IRQ_DOMAIN_HIERARCHY Kconfig
options.
Fixes: efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This is the only driver in the kernel source tree that depends on
IRQ_DOMAIN_HIERARCHY instead of selecting it. Since it is not a
visible Kconfig symbol, depending on it (expecting a user to
set/enable it) doesn't make much sense, so change it to select
instead of "depends on".
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: linux-gpio@vger.kernel.org
Cc: Thierry Reding <treding@nvidia.com>
Cc: Greentime Hu <greentime.hu@sifive.com>
Cc: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Make it clear that ACPI needs to be present only to get driver functional.
It is not required for compilation.
Fixes: 356b01a986a5 ("gpio: gpio-hisi: Add HiSilicon GPIO support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201214165524.43843-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This GPIO driver is for HiSilicon's ARM SoC.
HiSilicon's GPIO controller support double-edge interrupt and multi-core
concurrent access.
ACPI table example for this GPIO controller:
Device (GPO0)
{
Name (_HID, "HISI0184")
Device (PRTA)
{
Name (_ADR, Zero)
Name (_UID, Zero)
Name (_DSD, Package (0x01)
{
Package (0x02)
{
"ngpios",
0x20
}
})
}
}
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Link: https://lore.kernel.org/r/1607934255-52544-2-git-send-email-luojiaxing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.11-rc1
- several refactoring patches of the core gpiolib code
- add support for NXP PCAL9554B/C to gpio-pca953x
- allow probing mockup devices from device tree
- refactoring and improvements to gpio-rcar
- improvements to locking in gpio-tegra
- code shrink in gpiolib devres
- get the irq offset from device tree in gpio-sifive
- major refactoring of gpio-exar
- convert gpio-mvebu pwm access to regmap
- create a new submenu for virtual GPIO drivers
- fix clang fall-through warnings treewide
- minor driver refactoring and tweaks sprinkled all over
|
|
Since we already have a few virtual GPIO drivers, and more to come,
this category deserves its own submenu.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This adds a driver that supports the GPIO block found in
MStar/SigmaStar ARMv7 SoCs.
The controller seems to have enough register for 128 lines
but where they are wired up differs between chips and
no currently known chip uses anywhere near 128 lines so there
needs to be some per-chip data to collect together what lines
actually have physical pins attached and map the right names to them.
The core peripherals seem to use the same lines on the
currently known chips but the lines used for the sensor
interface, lcd controller etc pins seem to be totally
different between the infinity and mercury chips
The code tries to collect all of the re-usable names,
offsets etc together so that it's easy to build the extra
per-chip data for other chips in the future.
So far this only supports the MSC313 and MSC313E chips.
Support for the SSC8336N (mercury5) is trivial to add once
all of the lines have been mapped out.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201129110803.2461700-4-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If users select sysfs support they get the character device
as well so that end-users cannot complain that they
"only have sysfs on my system". They should have the
character device at all times.
If someone is in so dire need of stripping out the
character device while still enabling the sysfs ABI they
can very well patch the kernel.
Also only show this obsolete option to expert users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201110142724.14760-1-linus.walleij@linaro.org
|
|
We can simplify the code in gpio-exar by using regmap. This allows us to
drop the mutex (regmap provides its own locking) and we can also reuse
regmap's bit operations instead of implementing our own update function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for initialising shared (between children) Regmaps
- Add support for Kontron SL28CPLD
- Add support for ENE KB3930 Embedded Controller
- Add support for Intel FPGA PAC MAX 10 BMC
New Device Support:
- Add support for Power to Ricoh RN5T618
- Add support for UART to Intel Lakefield
- Add support for LP87524_Q1 to Texas Instruments LP87565
New Functionality:
- Device Tree; ene-kb3930, sl28cpld, syscon, lp87565, lp87524-q1
- Use new helper dev_err_probe(); madera-core, stmfx, wcd934x
- Use new GPIOD API; dm355evm_msp
- Add wake-up capability; sprd-sc27xx-spi
- Add ACPI support; kempld-core
Fix-ups:
- Trivial (spelling/whitespace); Kconfig, ab8500
- Fix for unused variables; khadas-mcu, kempld-core
- Remove unused header file(s); mt6360-core
- Use correct IRQ flags in docs; act8945a, gateworks-gsc, rohm,bd70528-pmic
- Add COMPILE_TEST support; asic3, tmio_core
- Add dependency on I2C; SL28CPLD
Bug Fixes:
- Fix memory leak(s); sm501
- Do not free regmap_config's 'name' until exit; syscon"
* tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (34 commits)
mfd: kempld-core: Fix unused variable 'kempld_acpi_table' when !ACPI
mfd: sl28cpld: Depend on I2C
mfd: asic3: Build if COMPILE_TEST=y
dt-bindings: mfd: Correct interrupt flags in examples
mfd: Add ACPI support to Kontron PLD driver
mfd: intel-m10-bmc: Add Intel MAX 10 BMC chip support for Intel FPGA PAC
mfd: lp87565: Add LP87524-Q1 variant
dt-bindings: mfd: Add LP87524-Q1
dt-bindings: mfd: lp87565: Convert to yaml
mfd: mt6360: Remove unused include <linux/version.h>
mfd: sm501: Fix leaks in probe()
mfd: syscon: Don't free allocated name for regmap_config
dt-bindings: mfd: syscon: Document Exynos3 and Exynos5433 compatibles
dt-bindings: mfd: syscon: Merge Samsung Exynos Sysreg bindings
dt-bindings: mfd: ab8500: Remove weird Unicode characters
mfd: sprd: Add wakeup capability for PMIC IRQ
mfd: intel-lpss: Add device IDs for UART ports for Lakefield
mfd: dm355evm_msp: Convert LEDs to GPIO descriptor table
mfd: wcd934x: Simplify with dev_err_probe()
mfd: stmfx: Simplify with dev_err_probe()
...
|
|
Add a build option to allow the removal of the CDEV v1 ABI.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Make the gpiolib-cdev module a build option. This allows the CDEV
interface to be removed from the kernel to reduce kernel size in
applications where is it not required, and provides the parent for
other CDEV interface specific build options to follow.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Change config to tristate, add module device table, module author,
description and license to support module build for i.MX GPIO driver.
As this is a SoC GPIO module, it provides common functions for most
of the peripheral devices, such as GPIO pins control, secondary
interrupt controller for GPIO pins IRQ etc., without GPIO driver, most
of the peripheral devices will NOT work properly, so GPIO module is
similar with clock, pinctrl driver that should be loaded ONCE and
never unloaded.
Since MXC GPIO driver needs to have init function to register syscore
ops once, here still use subsys_initcall(), NOT module_platform_driver().
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1600320829-1453-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.
A controller has 8 lines. There are three different flavors:
full-featured GPIO with interrupt support, input-only and output-only.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
GPIO-lib provides a ready-to-use interface to initialize an IRQ-chip on
top of a GPIO chip. It's better from maintainability and readability
point of view to use one instead of supporting a hand-written Generic
IRQ-chip-based implementation. Moreover the new implementation won't
cause much functional overhead but will provide a cleaner driver code.
All of that makes the DW APB GPIO driver conversion pretty much justified
especially seeing a tendency of the other GPIO drivers getting converted
too.
Here is what we do in the framework of this commit to convert the driver
to using the GPIO-lib-based IRQ-chip interface:
1) IRQ ack, mask and unmask callbacks are locally defined instead of
using the Generic IRQ-chip ones.
2) An irq_chip structure instance is embedded into the dwapb_gpio
private data. Note we can't have a static instance of that structure since
GPIO-lib will add some hooks into it by calling gpiochip_set_irq_hooks().
A warning about that would have been printed by the GPIO-lib code if we
used a single irq_chip structure instance for multiple DW APB GPIO
controllers.
3) Initialize the gpio_irq_chip structure embedded into the gpio_chip
descriptor. By default there is no IRQ enabled so any event raised will be
handled by the handle_bad_irq() IRQ flow handler. If DW APB GPIO IP-core
is synthesized to have non-shared reference IRQ-lines, then as before the
hierarchical and cascaded cases are distinguished by checking how many
parental IRQs are defined. (Note irq_set_chained_handler_and_data() won't
initialize IRQs, which descriptors couldn't be found.) If DW APB GPIO IP
is used on a platform with shared IRQ line, then we simply won't let the
GPIO-lib to initialize the parental IRQs, but will handle them locally in
the driver.
4) Discard linear IRQ-domain and Generic IRQ-chip initialization, since
GPIO-lib IRQ-chip interface will create a new domain and accept a standard
IRQ-chip structure pointer based on the setting we provided in the
gpio_irq_chip structure.
5) Manually select a proper IRQ flow handler directly in the
irq_set_type() callback by calling irq_set_handler_locked() method, since
an ordinary (not Generic) irq_chip descriptor is now utilized. Note this
shalln't give any regression
6) Alter CONFIG_GPIO_DWAPB kernel config to select
CONFIG_GPIOLIB_IRQCHIP instead of CONFIG_GENERIC_IRQ_CHIP.
Note neither 4) nor 5) shall cause a regression of commit 6a2f4b7dadd5
("gpio: dwapb: use a second irq chip"), since the later isn't properly
used here anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
NXP PCA9570 is a 4-bit I2C GPO expander without interrupt functionality.
Its ports are controlled only by a data byte without register address.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Datasheet: https://www.nxp.com/docs/en/data-sheet/PCA9570.pdf
Link: https://lore.kernel.org/r/20200709134829.216393-1-mans0n@gorani.run
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All config options for GPIO drivers are inside a big "if GPIOLIB ...
endif" block, so there is no reason for individual config options to
have expicit dependencies on GPIOLIB. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
There are quite a lot simple GPIO controller which are using regmap to
access the hardware. This driver tries to be a base to unify existing
code into one place. This won't cover everything but it should be a good
starting point.
It does not implement its own irq_chip because there is already a
generic one for regmap based devices. Instead, the irq_chip will be
instantiated in the parent driver and its irq domain will be associate
to this driver.
For now it consists of the usual registers, like set (and an optional
clear) data register, an input register and direction registers.
Out-of-the-box, it supports consecutive register mappings and mappings
where the registers have gaps between them with a linear mapping between
GPIO offset and bit position. For weirder mappings the user can register
its own .xlate().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-3-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.8 - part 2
- fix the initialization ordering in gpio-max730x
- make gpio-pxa buildable for compile testing
- make gpio-pca953x buildable as a module
|
|
Perhaps by some historical reasons the IRQ support has been allowed
only for built-in driver. However, there is nothing prevents us
to build it as module an use as IRQ chip.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add COMPILE_TEST support to the PXA GPIO driver for better compile
testing coverage.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
|
|
GPIO controllers are exported to userspace using /dev/gpiochip*
character devices. Access control to these devices is provided by
standard UNIX file system permissions, on an all-or-nothing basis:
either a GPIO controller is accessible for a user, or it is not.
Currently no mechanism exists to control access to individual GPIOs.
Hence add a GPIO driver to aggregate existing GPIOs, and expose them as
a new gpiochip.
This supports the following use cases:
- Aggregating GPIOs using Sysfs
This is useful for implementing access control, and assigning a set
of GPIOs to a specific user or virtual machine.
- Generic GPIO Driver
This is useful for industrial control, where it can provide
userspace access to a simple GPIO-operated device described in DT,
cfr. e.g. spidev for SPI-operated devices.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20200511145257.22970-5-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Allow driver to be built with COMPILE_TEST for better test coverage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512182721.55127-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is nothing in the driver requires OF_GPIO. Moreover, driver
supports ACPI and OF_GPIO may be a quite overhead on such configurations.
Drop dependency for good and replace of_gpio.h to of.h since we have
one function to be defined from there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512182721.55127-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enable building the PL061 GPIO driver as a module.
This does change the initcall level when built-in. This shouldn't be a
problem as any user should support deferred probe by now. A scan of DT
based platforms at least didn't reveal any users that would be a
problem.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add COMPILE_TEST support to GPIO_MXS driver for better compile
testing coverage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add COMPILE_TEST support to GPIO_MXC driver for better compile
testing coverage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This patch adds support for the GPIO controller used by
Mellanox BlueField 2 SOCs.
Signed-off-by: Asmaa Mnebhi <Asmaa@mellanox.com>
Link: https://lore.kernel.org/r/1680de9eb6d2b8855228dde9a2dd065f0dcbe1fb.1583182325.git.Asmaa@mellanox.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement provides:
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated
CPUs the interrupt could be routed to an isolated CPU which would
then be disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is
online in the assigned affinity mask the interrupt is routed to a
housekeeping CPU.
If there is no online housekeeping CPU in the affinity mask, then
the interrupt is routed to an isolated CPU to keep the device queue
intact, but unless the isolated CPU submits I/O by itself these
interrupts are not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI,
NXP INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code"
* tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
genirq, sched/isolation: Isolate from handling managed interrupts
irqchip/gic-v4.1: Allow direct invalidation of VLPIs
irqchip/gic-v4.1: Suppress per-VLPI doorbell
irqchip/gic-v4.1: Add VPE INVALL callback
irqchip/gic-v4.1: Add VPE eviction callback
irqchip/gic-v4.1: Add VPE residency callback
irqchip/gic-v4.1: Add mask/unmask doorbell callbacks
irqchip/gic-v4.1: Plumb skeletal VPE irqchip
irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP
irqchip/gic-v4.1: Don't use the VPE proxy if RVPEID is set
irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP
irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation
irqchip/gic-v3: Add GICv4.1 VPEID size discovery
irqchip/gic-v3: Detect GICv4.1 supporting RVPEID
irqchip/gic-v3-its: Fix get_vlpi_map() breakage with doorbells
irqdomain: Fix a memory leak in irq_domain_push_irq()
irqchip: Add NXP INTMUX interrupt multiplexer support
dt-bindings: interrupt-controller: Add binding for NXP INTMUX interrupt multiplexer
irqchip: Define EXYNOS_IRQ_COMBINER
irqchip/meson-gpio: Add support for meson a1 SoCs
...
|
|
ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
to be used for general purposes. First 3 can be used as outputs
and 4.th pin can be used as input. Allow them to be controlled
via GPIO framework.
The driver assumes all of the pins are configured as GPIOs and
trusts that the reserved pins in other OTP configurations are
excluded from control using "gpio-reserved-ranges" device tree
property (or left untouched by GPIO users).
Typical use for 4.th pin (input) is to use it as HALL sensor
input so that this pin state is toggled when HALL sensor detects
LID position change (from close to open or open to close). PMIC
HW implements some extra logic which allows PMIC to power-up the
system when this pin is toggled. Please see the data sheet for
details of GPIO options which can be selected by OTP settings.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Adds the GPIO driver for SiFive RISC-V SoCs.
Signed-off-by: Wesley W. Terpstra <wesley@sifive.com>
[Atish: Various fixes and code cleanup]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1575976274-13487-6-git-send-email-yash.shah@sifive.com
|
|
Linux 5.5-rc6
|
|
This patch adds support to wcd934x gpio block found in
WCD9340/WC9341 Audio codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200107130844.20763-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
