summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
2023-07-20Bluetooth: btusb: Fix bluetooth on Intel Macbook 2014Tomasz Moń
Commit c13380a55522 ("Bluetooth: btusb: Do not require hardcoded interface numbers") inadvertedly broke bluetooth on Intel Macbook 2014. The intention was to keep behavior intact when BTUSB_IFNUM_2 is set and otherwise allow any interface numbers. The problem is that the new logic condition omits the case where bInterfaceNumber is 0. Fix BTUSB_IFNUM_2 handling by allowing both interface number 0 and 2 when the flag is set. Fixes: c13380a55522 ("Bluetooth: btusb: Do not require hardcoded interface numbers") Reported-by: John Holland <johnbholland@icloud.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217651 Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no> Tested-by: John Holland<johnbholland@icloud.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-07-05Merge tag 'net-6.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from bluetooth, bpf and wireguard. Current release - regressions: - nvme-tcp: fix comma-related oops after sendpage changes Current release - new code bugs: - ptp: make max_phase_adjustment sysfs device attribute invisible when not supported Previous releases - regressions: - sctp: fix potential deadlock on &net->sctp.addr_wq_lock - mptcp: - ensure subflow is unhashed before cleaning the backlog - do not rely on implicit state check in mptcp_listen() Previous releases - always broken: - net: fix net_dev_start_xmit trace event vs skb_transport_offset() - Bluetooth: - fix use-bdaddr-property quirk - L2CAP: fix multiple UaFs - ISO: use hci_sync for setting CIG parameters - hci_event: fix Set CIG Parameters error status handling - hci_event: fix parsing of CIS Established Event - MGMT: fix marking SCAN_RSP as not connectable - wireguard: queuing: use saner cpu selection wrapping - sched: act_ipt: various bug fixes for iptables <> TC interactions - sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX - dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging - eth: sfc: fix null-deref in devlink port without MAE access - eth: ibmvnic: do not reset dql stats on NON_FATAL err Misc: - xsk: honor SO_BINDTODEVICE on bind" * tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits) nfp: clean mc addresses in application firmware when closing port selftests: mptcp: pm_nl_ctl: fix 32-bit support selftests: mptcp: depend on SYN_COOKIES selftests: mptcp: userspace_pm: report errors with 'remove' tests selftests: mptcp: userspace_pm: use correct server port selftests: mptcp: sockopt: return error if wrong mark selftests: mptcp: sockopt: use 'iptables-legacy' if available selftests: mptcp: connect: fail if nft supposed to work mptcp: do not rely on implicit state check in mptcp_listen() mptcp: ensure subflow is unhashed before cleaning the backlog s390/qeth: Fix vipa deletion octeontx-af: fix hardware timestamp configuration net: dsa: sja1105: always enable the send_meta options net: dsa: tag_sja1105: fix MAC DA patching from meta frames net: Replace strlcpy with strscpy pptp: Fix fib lookup calls. mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX xsk: Honor SO_BINDTODEVICE on bind ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported ...
2023-07-03virtio_bt: call scheduler when we free unused buffsXianting Tian
For virtio-net we were getting CPU stall warnings, and fixed it by calling the scheduler: see f8bb51043945 ("virtio_net: suppress cpu stall when free_unused_bufs"). This driver is similar so theoretically the same logic applies. Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com> Message-Id: <20230609131817.712867-4-xianting.tian@linux.alibaba.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2023-06-29Bluetooth: btusb: Add MT7922 bluetooth ID for the Asus AllyMatthew Anderson
Adding the device ID from the Asus Ally gets the bluetooth working on the device. Signed-off-by: Matthew Anderson <ruinairas1992@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-29Bluetooth: hci_bcm: do not mark valid bd_addr as invalidJohan Hovold
A recent commit restored the original (and still documented) semantics for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address is considered invalid unless an address is provided by firmware. This specifically means that this flag must only be set for devices with invalid addresses, but the Broadcom driver has so far been setting this flag unconditionally. Fortunately the driver already checks for invalid addresses during setup and sets the HCI_QUIRK_INVALID_BDADDR flag. Use this flag to indicate when the address can be overridden by firmware (long term, this should probably just always be allowed). Fixes: 6945795bc81a ("Bluetooth: fix use-bdaddr-property quirk") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/lkml/ecef83c8-497f-4011-607b-a63c24764867@samsung.com Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-29Bluetooth: btqca: use le32_to_cpu for ver.soc_idMin-Hua Chen
Use le32_to_cpu for ver.soc_id to fix the following sparse warning. drivers/bluetooth/btqca.c:640:24: sparse: warning: restricted __le32 degrades to integer Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-29Bluetooth: btusb: Add device 6655:8771 to device tablesDan Gora
This device is an Inspire branded BT 5.1 USB dongle with a Realtek RTL8761BU chip using the "Best Buy China" vendor ID. The device table is as follows: T: Bus=01 Lev=01 Prnt=02 Port=09 Cnt=01 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=6655 ProdID=8771 Rev=02.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms Signed-off-by: Dan Gora <dan.gora@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-29Bluetooth: btrtl: Add missing MODULE_FIRMWARE declarationsDan Gora
Add missing MODULE_FIRMWARE declarations for firmware referenced in btrtl.c. Signed-off-by: Dan Gora <dan.gora@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-05Bluetooth: hci_qca: fix debugfs registrationJohan Hovold
Since commit 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990"), the setup callback which registers the debugfs interface can be called multiple times. This specifically leads to the following error when powering on the controller: debugfs: Directory 'ibs' with parent 'hci0' already present! Add a driver flag to avoid trying to register the debugfs interface more than once. Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990") Cc: stable@vger.kernel.org # 4.20 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-05-19Bluetooth: btnxpuart: Fix compiler warningsNeeraj Sanjay Kale
This fixes the follwing compiler warning reported by kernel test robot: drivers/bluetooth/btnxpuart.c:1332:34: warning: unused variable 'nxpuart_of_match_table' [-Wunused-const-variable] Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202305161345.eClvTYQ9-lkp@intel.com/ Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btusb: Add WCN6855 devcoredump supportTim Jiang
WCN6855 will report memdump via ACL data or HCI event when it get crashed, so we collect memdump to debug firmware. Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btnxpuart: Enable flow control before checking boot signatureNeeraj Sanjay Kale
This enables flow control before checking for bootloader signature and deciding whether FW download is needed or not. In case of V1 bootloader chips w8987 and w8997, it is observed that if WLAN FW is downloaded first and power save is enabled in wlan core, bootloader signatures are not emitted by the BT core when the chip is put to sleep. As a result, the driver skips FW download and subsequent HCI commands get timeout errors in dmesg as shown below: [ 112.898867] Bluetooth: hci0: Opcode 0x c03 failed: -110 [ 114.914865] Bluetooth: hci0: Setting baudrate failed (-110) [ 116.930856] Bluetooth: hci0: Setting wake-up method failed (-110) By enabling the flow control, the host enables its RTS pin, and an interrupt in chip's UART peripheral causes the bootloader to wake up, enabling the bootloader signatures, which then helps in downloading the bluetooth FW file. This changes all instances of 0/1 for serdev_device_set_flow_control() to false/true. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btrtl: Add the support for RTL8851BMax Chou
Add the support for RTL8851B BT controller on USB interface. The necessary firmware will be submitted to linux-firmware project. Note that the Bluetooth devices WITH the VID=0x0bda would be set the feature quirk in btrtl_setup_realtek(). It's able to ignore the feature flag set for the specific VID and PID in blacklist_table[] of btusb.c. (check [1]) If Realtek Bluetooth chips WITHOUT the VID=0x0bda, it shall be added the feature flag for the specific VID and PID in blacklist_table[] of btusb.c. (check [2]) [1] '9ab9235fe5cf ("Bluetooth: btrtl: Enable WBS for the specific Realtek devices")' [2] '73280f13c9bb ("Bluetooth: btusb: Add the more support IDs for Realtek RTL8822CE")' The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 33 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=b851 Rev= 0.00 S: Manufacturer=Realtek S: Product=802.11ax WLAN Adapter S: SerialNumber=00E04C885A01 C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btnxpuart: Fix sparse warningsLuiz Augusto von Dentz
This fixes the following sparse warnings: drivers/bluetooth/btnxpuart.c:681:23: sparse: sparse: restricted __le16 degrades to integer drivers/bluetooth/btnxpuart.c:690:82: sparse: sparse: incorrect type in argument 2 (different base types) @@ expected unsigned short [usertype] req_len @@ got restricted __le16 [usertype] len @@ drivers/bluetooth/btnxpuart.c:690:82: sparse: expected unsigned short [usertype] req_len drivers/bluetooth/btnxpuart.c:690:82: sparse: got restricted __le16 [usertype] len drivers/bluetooth/btnxpuart.c:694:84: sparse: sparse: incorrect type in argument 2 (different base types) @@ expected unsigned short [usertype] req_len @@ got restricted __le16 [usertype] len @@ drivers/bluetooth/btnxpuart.c:694:84: sparse: expected unsigned short [usertype] req_len drivers/bluetooth/btnxpuart.c:694:84: sparse: got restricted __le16 [usertype] len drivers/bluetooth/btnxpuart.c:708:23: sparse: sparse: incorrect type in assignment (different base types) @@ expected unsigned int [usertype] requested_len @@ got restricted __le16 [usertype] len @@ drivers/bluetooth/btnxpuart.c:708:23: sparse: expected unsigned int [usertype] requested_len drivers/bluetooth/btnxpuart.c:708:23: sparse: got restricted __le16 [usertype] len drivers/bluetooth/btnxpuart.c:787:78: sparse: sparse: incorrect type in argument 2 (different base types) @@ expected unsigned short [usertype] chipid @@ got restricted __le16 [usertype] chip_id @@ drivers/bluetooth/btnxpuart.c:787:78: sparse: expected unsigned short [usertype] chipid drivers/bluetooth/btnxpuart.c:787:78: sparse: got restricted __le16 [usertype] chip_id drivers/bluetooth/btnxpuart.c:810:74: sparse: sparse: incorrect type in argument 2 (different base types) @@ expected unsigned short [usertype] req_len @@ got restricted __le16 [usertype] len @@ drivers/bluetooth/btnxpuart.c:810:74: sparse: expected unsigned short [usertype] req_len drivers/bluetooth/btnxpuart.c:810:74: sparse: got restricted __le16 [usertype] len drivers/bluetooth/btnxpuart.c:815:76: sparse: sparse: incorrect type in argument 2 (different base types) @@ expected unsigned short [usertype] req_len @@ got restricted __le16 [usertype] len @@ drivers/bluetooth/btnxpuart.c:815:76: sparse: expected unsigned short [usertype] req_len drivers/bluetooth/btnxpuart.c:815:76: sparse: got restricted __le16 [usertype] len drivers/bluetooth/btnxpuart.c:834:16: sparse: sparse: restricted __le32 degrades to integer drivers/bluetooth/btnxpuart.c:843:55: sparse: sparse: restricted __le32 degrades to integer drivers/bluetooth/btnxpuart.c:844:36: sparse: sparse: incorrect type in argument 3 (different base types) @@ expected unsigned long [usertype] @@ got restricted __le16 [usertype] len @@ drivers/bluetooth/btnxpuart.c:844:36: sparse: expected unsigned long [usertype] drivers/bluetooth/btnxpuart.c:844:36: sparse: got restricted __le16 [usertype] len Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202304160736.Tsa0zTBU-lkp@intel.com/ Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btrtl: Firmware format v2 supportMax Chou
Realtek changed the format of the firmware file as v2. The driver should implement the patch to extract the firmware data from the firmware file. The future chips must apply this patch for firmware loading. This patch is compatible with the both previous format and v2 as well. Signed-off-by: Allen Chen <allen_chen@realsil.com.cn> Signed-off-by: Alex Lu <alex_lu@realsil.com.cn> Tested-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Revert "Bluetooth: btsdio: fix use after free bug in btsdio_remove due to ↵Liu Jian
unfinished work" This reverts commit 1e9ac114c4428fdb7ff4635b45d4f46017e8916f. This patch introduces a possible null-ptr-def problem. Revert it. And the fixed bug by this patch have resolved by commit 73f7b171b7c0 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race condition"). Fixes: 1e9ac114c442 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: Add new quirk for broken set random RPA timeout for ATS2851Raul Cheleguini
The ATS2851 based controller advertises support for command "LE Set Random Private Address Timeout" but does not actually implement it, impeding the controller initialization. Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller initialization. < HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2 Timeout: 900 seconds > HCI Event: Command Status (0x0f) plen 4 LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1 Status: Unknown HCI Command (0x01) Co-developed-by: imoc <wzj9912@gmail.com> Signed-off-by: imoc <wzj9912@gmail.com> Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: vhci: Fix info leak in force_devcd_write()Dan Carpenter
There are a number of bugs here: 1) If "count" is less than sizeof(dump_data.data) then it copies uninitialized data. 2) If simple_write_to_buffer() returns -EFAULT then we run into a problem "ret < count" comparison. "count" is an unsigned long so the comparison is type promoted to unsigned long and the negative returns become high positive values. That also results in copying uninitialized data. 3) If "*ppos" is non-zero then the first part of the dump_data buffer is uninitialized. Using copy_from_user() instead of simple_write_to_buffer() is more appropriate here. Fixes: d5d5df6da0aa ("Bluetooth: Add vhci devcoredump support") Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_qca: mark OF related data as maybe unusedSteev Klimaszewski
The driver can be compile tested with !CONFIG_OF making certain data unused. Signed-off-by: Steev Klimaszewski <steev@kali.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btnxpuart: No need to check the received bootloader signatureNeeraj Sanjay Kale
We can never assume the uart will deliver a complete packet to the BT layer at once, the expected packet may be divided into several parts by uart as uart doesn't know the received packet size, the received data count may mismatch with the expected packet size, so here is_valid_bootloader_signature() check may always return false. Even we remove the count check in is_valid_bootloader_signature(), then the first part of the data which includes the packet type can pass the is_valid_bootloader_signature() check, but the remaining parts don't have the packet type data still cannot pass the check, here return directly will cause the data loss. So need to remove the received bootloader signature check here, the h4_recv_buf() can help us combine the different data received into one packet. If any out-of-sync or incomplete bootloader signature is received, it is safe to ignore and discard it, and process the next bootloader signature. Co-developed-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btnxpuart: Disable Power Save feature on startupNeeraj Sanjay Kale
This sets the default power save mode setting to disabled. With this setting, this driver will behave like a normal h4 driver. If user needs to use the power save feature, it can be enabled using the following vendor command: hcitool cmd 3f 23 02 00 00 (HCI_NXP_AUTO_SLEEP_MODE) Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btnxpuart: Deasset UART break before closing serdev deviceNeeraj Sanjay Kale
This adds a call to ps_wakeup() before closing the serdev device, to de-assert UART break. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btnxpuart: Add support to download helper FW file for w8997Neeraj Sanjay Kale
This adds support to download helper FW file for the legacy NXP chipset 88w8997 for the btnxpuart driver. This helper FW file is necessary to set the bootloader baudrate to 3000000 after which the actual BT FW file can be downloaded. This change helps bring the FW download time from around 10 sec to less than 2 sec for 88w8997 chip. For newer chipsets, both V1 and V3 bootloader, driver sends the cmd5 and cmd7 to the chip bootloader, and does not need a helper FW file. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_bcm: Add Acer Iconia One 7 B1-750 to the bcm_broken_irq_dmi_tableHans de Goede
The DSDT for the Acer Iconia One 7 B1-750 models (which share the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but this is not correct. Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO controller for the IRQ and this pin is _not_ configured in direct IRQ mode by the firmware. Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table, to fix bluetooth not working on these tablets. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_bcm: Add Lenovo Yoga Tablet 2 830 / 1050 to the ↵Hans de Goede
bcm_broken_irq_dmi_table The DSDT for the Lenovo Yoga Tablet 2 830 / 1050 models (which share the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but this is not correct. Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO controller for the IRQ and this pin is _not_ configured in direct IRQ mode by the firmware. Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table, to fix bluetooth not working on these tablets. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_bcm: Limit bcm43430a0 / bcm43430a1 baudrate to 2000000Hans de Goede
The bcm43430a0 and bcm43430a1 BT does not support the 0xfc45 command to set the UART clock to 48 MHz and it also does not work at 4000000 baud without this command as some newer models do. These chips are found on ACPI/x86 devices where the operating baudrate does not come from the firmware but is hardcoded at 4000000, which does not work. Add a max_baudrate value to struct bcm_device_data and set this to 2000000 on all known ACPI hardware-ids for the bcm43430a0 and the bcm43430a1. Note this also adds the BCM2E9F ACPI HID which was missing until now. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_bcm: Fall back to getting bdaddr from EFI if not setHans de Goede
On some devices the BCM Bluetooth adapter does not have a valid bdaddr set. btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is the case. But this requires users to manual setup a btaddr, by doing e.g.: btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3' Which means that Bluetooth will not work out of the box on such devices. To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY which tries to get the bdaddr from devicetree. But this only works on devicetree platforms. On UEFI based platforms there is a special Broadcom UEFI variable which when present contains the devices bdaddr, just like how there is another UEFI variable which contains wifi nvram contents including the wifi MAC address. Add support for getting the bdaddr from this Broadcom UEFI variable, so that Bluetooth will work OOTB for users on devices where this UEFI variable is present. This fixes Bluetooth not working on for example Asus T100HA 2-in-1s. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_h5: Complements reliable packet processing logicQiqi Zhang
As shown in the schematic diagram below.There may be a critical scenario in the current code. If the device does not receive an pure ack sent by the host due to insufficient receive buffer or other reasons and triggers a retransmission, the host will always be in an 'out-of-order' state.The state machine will get stuck. host device SEQ3,ACK4 ---------> <--------- SEQ4,ACK4 pure ACK ---------> (not received) (out-of-order) <--------- SEQ4,ACK4(retransmission) ........ (out-of-order) <--------- SEQ4,ACK4(retransmission) According to the description in the core specification: "whenever a reliable packet is received, an acknowledgment shall be generated." So set H5_TX_ACK_REQ bit to trigger retransmission of pure ack packet when "out-of-order" occurs. Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btintel: Add Intel devcoredump supportAbhishek Pandit-Subedi
Intercept debug exception events from the controller and put them into a devcoredump using hci devcoredump APIs. The debug exception contains data in a TLV format and it will be parsed in userspace. Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Manish Mandlik <mmandlik@google.com> Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btusb: Add btusb devcoredump supportManish Mandlik
This patch implements the btusb driver side .coredump() callback to trigger a devcoredump via sysfs. Signed-off-by: Manish Mandlik <mmandlik@google.com> Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: Add vhci devcoredump supportManish Mandlik
Add devcoredump support for vhci that creates forcce_devcoredump debugfs entry. This is used for mgmt-tester tests. Signed-off-by: Manish Mandlik <mmandlik@google.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btintel: Add LE States quirk supportChethan T N
Basically all Intel controllers support both Central/Peripheral LE states. This patch enables the LE States quirk by default on all Solar and Magnertor Intel controllers. Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855Steev Klimaszewski
Add regulators, GPIOs and changes required to power on/off wcn6855. Add support for firmware download for wcn6855 which is in the linux-firmware repository as hpbtfw21.tlv and hpnv21.bin. Based on the assumption that this is similar to the wcn6750 Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1 Signed-off-by: Steev Klimaszewski <steev@kali.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Tested-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btrtl: check for NULL in btrtl_set_quirks()Max Chou
The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since b8e482d02513. However, if installing a Realtek Bluetooth controller without the driver supported, it will hit the NULL point accessed. Add a check for NULL to avoid the Kernel Oops. Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23bluetooth: Add device 13d3:3571 to device tablesLarry Finger
This device is part of a Realtek RTW8852BE chip. The device table is as follows: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3571 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23bluetooth: Add device 0bda:887b to device tablesLarry Finger
This device is part of a Realtek RTW8852BE chip. The device table entry is as follows: T: Bus=03 Lev=01 Prnt=01 Port=12 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=887b Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: NXP: select CONFIG_CRC8Arnd Bergmann
The driver needs both CRC32 and CRC8 to link correctly: ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe': drivers/bluetooth/btnxpuart.c:1214: undefined reference to `crc8_populate_msb' ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack': drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8' ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8' Fixes: 3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsetsNeeraj Sanjay Kale
This adds a driver based on serdev driver for the NXP BT serial protocol based on running H:4, which can enable the built-in Bluetooth device inside an NXP BT chip. This driver has Power Save feature that will put the chip into sleep state whenever there is no activity for 2000ms, and will be woken up when any activity is to be initiated over UART. This driver enables the power save feature by default by sending the vendor specific commands to the chip during setup. During setup, the driver checks if a FW is already running on the chip by waiting for the bootloader signature, and downloads device specific FW file into the chip over UART if bootloader signature is received.. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_ldisc: Fix tty_set_termios() return value assumptionsIlpo Järvinen
tty_set_termios() never returns anything else than 0. Make the debug prints to look directly into the new termios instead to check CRTSCTS state. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: Improve support for Actions Semi ATS2851 based devicesRaul Cheleguini
Add two more quirks to resume the device initialization and basic operation as the device seems not to support "Read Transmit Power" and "Set Extended Scan Parameters". < HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0 > HCI Event: Command Status (0x0f) plen 4 LE Read Transmit Power (0x08|0x004b) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Status (0x0f) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Unknown HCI Command (0x01) Signed-off-by: Raul Cheleguini <rcheleguini@google.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btrtl: add support for the RTL8723CSVasily Khoruzhick
The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth module which is connected via UART to the host. It shares lmp subversion with 8703B, so Realtek's userspace initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS (CG, VF, XX) with RTL8703B using vendor's command to read chip type. Also this chip declares support for some features it doesn't support so add a quirk to indicate that these features are broken. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Bastian Germann <bage@debian.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btmtkuart: mark OF related data as maybe unusedKrzysztof Kozlowski
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_qca: mark OF related data as maybe unusedKrzysztof Kozlowski
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btmrvl_sdio: mark OF related data as maybe unusedKrzysztof Kozlowski
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/bluetooth/btmrvl_sdio.c:43:34: error: ‘btmrvl_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_ll: drop of_match_ptr for ID tableKrzysztof Kozlowski
The driver can match only via the DT table so the table should be always used and the of_match_ptr does not have any sense (this also allows ACPI matching via PRP0001, even though it might not be relevant here). drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: Add VID/PID 0489/e0e4 for MediaTek MT7922Meng Tang
Tested on Acer Nitro AN515-47 Notebook output from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e4 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Meng Tang <tangmeng@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_h5: btrtl: Add support for RTL8821CSChris Morgan
RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART interface. Note that the firmware this was tested with was firmware version 0x75b8f098. Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btusb: Add new PID/VID 04ca:3801 for MT7663Meng Tang
This bluetooth device is found in a combo WLAN/BT card for a MediaTek 7663. Tested on Acer Aspire A315-24P Notebook The device information: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3801 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Meng Tang <tangmeng@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: btrtl: Add support for RTL8852BSVictor Hassan
Add the support for RTL8852BS BT controller on UART interface. The necessary firmware file will be submitted to linux-firmware. Signed-off-by: Victor Hassan <victor@allwinnertech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-04-23Bluetooth: hci_mrvl: Add serdev support for 88W8997Stefan Eichenberger
Add serdev support for the 88W8997 from NXP (previously Marvell). It includes support for changing the baud rate. The command to change the baud rate is taken from the user manual UM11483 Rev. 9 in section 7 (Bring-up of Bluetooth interfaces) from NXP. Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>