| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small fixes, one in drivers.
The core changes are to the internal representation of flags in
scsi_devices which removes space wasting bools in favour of single bit
flags and to add a flag to force a runtime resume which is used by ATA
devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix system start for ATA devices
scsi: Change SCSI device boolean fields to single bit flags
scsi: ufs: core: Clear cmd if abort succeeds in MCQ mode
|
|
It is not always possible to keep a device in the runtime suspended state
when a system level suspend/resume cycle is executed. E.g. for ATA devices
connected to AHCI adapters, system resume resets the ATA ports, which
causes connected devices to spin up. In such case, a runtime suspended disk
will incorrectly be seen with a suspended runtime state because the device
is not resumed by sd_resume_system(). The power state seen by the user is
different than the actual device physical power state.
Fix this issue by introducing the struct scsi_device flag
force_runtime_start_on_system_start. When set, this flag causes
sd_resume_system() to request a runtime resume operation for runtime
suspended devices. This results in the user seeing the device runtime_state
as active after a system resume, thus correctly reflecting the device
physical power state.
Fixes: 9131bff6a9f1 ("scsi: core: pm: Only runtime resume if necessary")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-3-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop
management") changed the single bit manage_start_stop flag into 2 boolean
fields of the SCSI device structure. Commit 24eca2dce0f8 ("scsi: sd:
Introduce manage_shutdown device flag") introduced the manage_shutdown
boolean field for the same structure. Together, these 2 commits increase
the size of struct scsi_device by 8 bytes by using booleans instead of
defining the manage_xxx fields as single bit flags, similarly to other
flags of this structure.
Avoid this unnecessary structure size increase and be consistent with the
definition of other flags by reverting the definitions of the manage_xxx
fields as single bit flags.
Fixes: 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop management")
Fixes: 24eca2dce0f8 ("scsi: sd: Introduce manage_shutdown device flag")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-2-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add missing error return check for devm_ioport_map() and return the
error if this function call fails.
Fixes: 0d5ff566779f ("libata: convert to iomap")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
On today's platforms the benefit of platform_driver_probe() isn't that
relevant any more. It allows to drop some code after booting (or module
loading) for .probe() and discard the .remove() function completely if
the driver is built-in. This typically saves a few 100k.
The downside of platform_driver_probe() is that the driver cannot be
bound and unbound at runtime which is ancient and so slightly
complicates testing. There are also thoughts to deprecate
platform_driver_probe() because it adds some complexity in the driver
core for little gain. Also many drivers don't use it correctly. This
driver for example misses to mark the driver struct with __ref which is
needed to suppress a (W=1) modpost warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
On today's platforms the benefit of platform_driver_probe() isn't that
relevant any more. It allows to drop some code after booting (or module
loading) for .probe() and discard the .remove() function completely if
the driver is built-in. This typically saves a few 100k.
The downside of platform_driver_probe() is that the driver cannot be
bound and unbound at runtime which is ancient and so slightly
complicates testing. There are also thoughts to deprecate
platform_driver_probe() because it adds some complexity in the driver
core for little gain. Also many drivers don't use it correctly. This
driver for example misses to mark the driver struct with __ref which is
needed to suppress a (W=1) modpost warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
This reverts commit 5b6fba546da246b3d0dd8465c07783e22629cc53.
Commit 5b6fba546da2 ("ata: libata-core: Detach a port devices on
shutdown") modified the function ata_pci_shutdown_one() to stop
(suspend) devices attached to the ports of a PCI AHCI adapter to ensure
that drives are spun down before shutting down a system. However, this
is done only for PCI adapters and not for other types of adapters. This
limitation was addressed with commit 24eca2dce0f8 ("scsi: sd: Introduce
manage_shutdown device flag"). With this, all ATA disks are spun down on
system shutdown, which make the changes introduced with 5b6fba546da2
useless.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA updates from Damien Le Moal:
- Modify the AHCI driver to print the link power management policy used
on scan, to help with debugging issues (Niklas)
- Add support for the ASM2116 series adapters to the AHCI driver
(Szuying)
- Prepare libata for the coming gcc and Clang __counted_by attribute
(Kees)
- Following the recent estensive fixing of libata suspend/resume
handling, several patches further cleanup and improve disk power
state management (me)
- Reduce the verbosity of some error messages for non-fatal temporary
errors, e.g. slow response to device reset when scanning a port, and
warning messages that are in fact normal, e.g. disabling a device on
suspend or when removing it (me)
- Cleanup DMA helper functions (me)
- Fix sata_mv drive handling of potential errors durring probe (Ma)
- Cleanup the xgene and imx drivers using the functions
of_device_get_match_data() and device_get_match_data() (Rob)
- Improve the tegra driver device tree (Rob)
* tag 'ata-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (22 commits)
dt-bindings: ata: tegra: Disallow undefined properties
ata: libata-core: Improve ata_dev_power_set_active()
ata: libata-eh: Spinup disk on resume after revalidation
ata: imx: Use device_get_match_data()
ata: xgene: Use of_device_get_match_data()
ata: sata_mv: aspeed: fix value check in mv_platform_probe()
ata: ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list
ata: libata: Cleanup inline DMA helper functions
ata: libata-eh: Reduce "disable device" message verbosity
ata: libata-eh: Improve reset error messages
ata: libata-sata: Improve ata_sas_slave_configure()
ata: libata-core: Do not resume runtime suspended ports
ata: libata-core: Do not poweroff runtime suspended ports
ata: libata-core: Remove ata_port_resume_async()
ata: libata-core: Remove ata_port_suspend_async()
ata: libata-core: Detach a port devices on shutdown
ata: libata-core: Synchronize ata_port_detach() with hotplug
ata: libata-scsi: Cleanup ata_scsi_start_stop_xlat()
scsi: Remove scsi device no_start_on_resume flag
ata: libata: Annotate struct ata_cpr_log with __counted_by
...
|
|
Commit aa3998dbeb3a ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").
Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.
Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.
To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.
Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Improve the function ata_dev_power_set_active() by having it do nothing
for a disk that is already in the active power state. To do that,
introduce the function ata_dev_power_is_active() to test the current
power state of the disk and return true if the disk is in the PM0:
active or PM1: idle state (0xff value for the count field of the CHECK
POWER MODE command output).
To preserve the existing behavior, if the CHECK POWER MODE command
issued in ata_dev_power_is_active() fails, the drive is assumed to be in
standby mode and false is returned.
With this change, issuing the VERIFY command to access the disk media to
spin it up becomes unnecessary most of the time during system resume as
the port reset done by libata-eh on resume often result in the drive to
spin-up (this behavior is not clearly defined by the ACS specifications
and may thus vary between disk models).
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
Move the call to ata_dev_power_set_active() to transition a disk in
standby power mode to the active power mode from
ata_eh_revalidate_and_attach() before doing revalidation to the end of
ata_eh_recover(), after the link speed for the device is reconfigured
(if that was necessary). This is safer as this ensure that the VERIFY
command executed to spinup the disk is executed with the drive properly
reconfigured first.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Use preferred of_device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
In mv_platform_probe(), check the return value of clk_prepare_enable()
and return the error code if clk_prepare_enable() returns an
unexpected value.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
fit3 protocol driver does not support accessing IDE control registers
(device control/altstatus). The DOS driver does not use these registers
either (as observed from DOSEMU trace). But the HW seems to be capable
of accessing these registers - I simply tried bit 3 and it works!
The control register is required to properly reset ATAPI devices or
they will be detected only once (after a power cycle).
Tested with EXP Computer CD-865 with MC-1285B EPP cable and
TransDisk 3000.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Some parallel adapters (e.g. EXP Computer MC-1285B EPP Cable) return
bogus values when there's no master device present. This can cause
reset to fail, preventing the lone slave device (such as EXP Computer
CD-865) from working.
Add custom version of wait_after_reset that ignores master failure when
a slave device is present. The custom version is also needed because
the generic ata_sff_wait_after_reset uses direct port I/O for slave
device detection.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Add missing ops->sff_set_devctl implementation.
Fixes: 246a1c4c6b7f ("ata: pata_parport: add driver (PARIDE replacement)")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
There's a 'x' missing in 0x55 in pata_parport_devchk(), causing the
detection to always fail. Fix it.
Fixes: 246a1c4c6b7f ("ata: pata_parport: add driver (PARIDE replacement)")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Intel Alder Lake-P AHCI controller needs to be added to the mobile
chipsets list in order to have link power management enabled. Without
this the CPU cannot enter lower power C-states making idle power
consumption high.
Cc: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
There is no point in warning about a device being disabled when we
expect it to be, that is, on suspend, shutdown or when detaching the
device.
Suppress the message "disable device" for these cases by introducing the
EH static function ata_eh_dev_disable() and by using it in
ata_eh_unload() and ata_eh_detach_dev(). ata_dev_disable() code is
modified to call this new function after printing the "disable device"
message.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some drives are really slow to spinup on resume, resulting is a very
slow response to COMRESET and to error messages such as:
ata1: COMRESET failed (errno=-16)
ata1: link is slow to respond, please be patient (ready=0)
ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata1.00: configured for UDMA/133
Given that the slowness of the response is indicated with the message
"link is slow to respond..." and that resets are retried until the
device is detected as online after up to 1min (ata_eh_reset_timeouts),
there is no point in printing the "COMRESET failed" error message. Let's
not scare the user with non fatal errors and only warn about reset
failures in ata_eh_reset() when all reset retries have been exhausted.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change ata_sas_slave_configure() to return the return value of
ata_scsi_dev_config() to ensure that any error from that function is
propagated to libsas.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The scsi disk driver does not resume disks that have been runtime
suspended by the user. To be consistent with this behavior, do the same
for ata ports and skip the PM request in ata_port_pm_resume() if the
port was already runtime suspended. With this change, it is no longer
necessary to force the PM state of the port to ACTIVE as the PM core
code will take care of that when handling runtime resume.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When powering off, there is no need to suspend a port that has already
been runtime suspended. Skip the EH PM request in ata_port_pm_poweroff()
in this case.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove ata_port_resume_async() and replace it with a modified
ata_port_resume() taking an additional bool argument indicating if
ata EH resume operation should be executed synchronously or
asynchronously. With this change, the variable ata_port_resume_ehi is
not longer necessary and its value (ATA_EHI_XXX flags) passed directly
to ata_port_request_pm().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ata_port_suspend_async() is only called by ata_sas_port_suspend().
Modify ata_port_suspend() with an additional bool argument indicating an
asynchronous or synchronous suspend to allow removing that helper
function. With this change, the variable ata_port_resume_ehi can also be
removed and its value (ATA_EHI_XXX flags passed directly to
ata_port_request_pm().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Modify ata_pci_shutdown_one() to schedule EH to unload a port devices
before freezing and thawing the port. This ensures that drives are
cleanly disabled and transitioned to standby power mode when
a PCI adapter is removed or the system is powered off.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The call to async_synchronize_cookie() to synchronize a port removal
and hotplug probe is done in ata_host_detach() right before calling
ata_port_detach(). Move this call at the beginning of ata_port_detach()
to ensure that this operation is always synchronized with probe.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that libata does its own internal device power mode management
through libata EH, the scsi disk driver will not issue START STOP UNIT
commands anymore. We can receive this command only from user passthrough
operations. So there is no need to consider the system state and ATA
port flags for suspend to translate the command.
Since setting up the taskfile for the verify and standby
immediate commands is the same as done in ata_dev_power_set_active()
and ata_dev_power_set_standby(), factor out this code into the helper
function ata_dev_power_init_tf() to simplify ata_scsi_start_stop_xlat()
as well as ata_dev_power_set_active() and ata_dev_power_set_standby().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support for PCIe SATA adapter cards based on Asmedia 2116 controllers.
These cards can provide up to 10 SATA ports on PCIe card.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
The target LPM policy can be set using either a Kconfig or a kernel module
parameter.
However, if the board type is set to anything but board_ahci_low_power,
then the LPM policy will overridden and set to ATA_LPM_UNKNOWN.
Additionally, if the default suspend is suspend to idle, depending on the
hardware capabilities of the HBA, ahci_update_initial_lpm_policy() might
override the LPM policy to either ATA_LPM_MIN_POWER_WITH_PARTIAL or
ATA_LPM_MIN_POWER.
All this means that it is very hard to know which LPM policy a user will
actually be using on a given system.
In order to make it easier to debug LPM related issues, print the LPM
policy on boot.
One common LPM related issue is that the device fails to link up.
Because of that, we cannot add this print to ata_dev_configure(), as that
function is only called after a successful link up. Instead, add the info
using ata_port_desc(), with the help of a new ata_port_desc_misc() helper.
The port description is printed once per port during boot.
Before changes:
ata1: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780100 irq 170
ata2: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780180 irq 170
After changes:
ata1: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780100 irq 170 lpm-pol 4
ata2: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780180 irq 170 lpm-pol 4
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
"A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more detail:
- Add missing additionalProperties on child nodes to the pata-common
DT bindings (Rob)
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas)
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias)
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me)
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk
driver resume operation not being synchronized with libata EH port
resume handling.
This is addressed by changing the scsi disk driver disk start/stop
control to allow libata to execute disk suspend (spin down) and
resume (spin up) on its own during system suspend/resume. Runtime
suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races
- Establish a link between ATA ports and SCSI devices to order PM
operations
- Fix device removal to avoid issues with driver rmmod removal
- Fix synchronization of libata device rescan and SCSI disk resume
operation
- Remove libsas PM operations as suspend/resume is handled
directly by the sas controller resume
- Fix the SCSI disk driver to not issue commands to suspended
disks, thus avoiding potential system lock-up on resume"
* tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-eh: Fix compilation warning in ata_eh_link_report()
ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
scsi: sd: Do not issue commands to suspended disks on shutdown
ata: libata-core: Do not register PM operations for SAS ports
ata: libata-scsi: Fix delayed scsi_rescan_device() execution
scsi: Do not attempt to rescan suspended devices
ata: libata-scsi: Disable scsi device manage_system_start_stop
scsi: sd: Differentiate system and runtime start/stop management
ata: libata-scsi: link ata port and scsi device
ata: libata-core: Fix port and device removal
ata: libata-core: Fix ata_port_request_pm() locking
ata: libata-sata: increase PMP SRST timeout to 10s
ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
dt-bindings: ata: pata-common: Add missing additionalProperties on child nodes
|
|
The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:
drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2372 | ap->eh_tries);
| ~~~~~~~~~~~~~
Avoid this warning by increasing the string size to 16B.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The 24 bytes length allocated to the ncq_desc string in
ata_dev_config_lba() for ata_dev_config_ncq() to use is too short,
causing the following gcc compilation warnings when compiling with W=1:
drivers/ata/libata-core.c: In function ‘ata_dev_configure’:
drivers/ata/libata-core.c:2378:56: warning: ‘%d’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~
In function ‘ata_dev_config_ncq’,
inlined from ‘ata_dev_config_lba’ at drivers/ata/libata-core.c:2649:8,
inlined from ‘ata_dev_configure’ at drivers/ata/libata-core.c:2952:9:
drivers/ata/libata-core.c:2378:41: note: directive argument in the range [1, 32]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~
drivers/ata/libata-core.c:2378:17: note: ‘snprintf’ output between 16 and 31 bytes into a destination of size 24
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2379 | ddepth, aa_desc);
| ~~~~~~~~~~~~~~~~
Avoid these warnings and the potential truncation by changing the size
of the ncq_desc string to 32 characters.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
libsas does its own domain based power management of ports. For such
ports, libata should not use a device type defining power management
operations as executing these operations for suspend/resume in addition
to libsas calls to ata_sas_port_suspend() and ata_sas_port_resume() is
not necessary (and likely dangerous to do, even though problems are not
seen currently).
Introduce the new ata_port_sas_type device_type for ports managed by
libsas. This new device type is used in ata_tport_add() and is defined
without power management operations.
Fixes: 2fcbdcb4c802 ("[SCSI] libata: export ata_port suspend/resume infrastructure for sas")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after
device resume") modified ata_scsi_dev_rescan() to check the scsi device
"is_suspended" power field to ensure that the scsi device associated
with an ATA device is fully resumed when scsi_rescan_device() is
executed. However, this fix is problematic as:
1) It relies on a PM internal field that should not be used without PM
device locking protection.
2) The check for is_suspended and the call to scsi_rescan_device() are
not atomic and a suspend PM event may be triggered between them,
casuing scsi_rescan_device() to be called on a suspended device and
in that function blocking while holding the scsi device lock. This
would deadlock a following resume operation.
These problems can trigger PM deadlocks on resume, especially with
resume operations triggered quickly after or during suspend operations.
E.g., a simple bash script like:
for (( i=0; i<10; i++ )); do
echo "+2 > /sys/class/rtc/rtc0/wakealarm
echo mem > /sys/power/state
done
that triggers a resume 2 seconds after starting suspending a system can
quickly lead to a PM deadlock preventing the system from correctly
resuming.
Fix this by replacing the check on is_suspended with a check on the
return value given by scsi_rescan_device() as that function will fail if
called against a suspended device. Also make sure rescan tasks already
scheduled are first cancelled before suspending an ata port.
Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
|
|
Whenever an ATA adapter driver is removed (e.g. rmmod),
ata_port_detach() is called repeatedly for all the adapter ports to
remove (unload) the devices attached to the port and delete the port
device itself. Removing of devices is done using libata EH with the
ATA_PFLAG_UNLOADING port flag set. This causes libata EH to execute
ata_eh_unload() which disables all devices attached to the port.
ata_port_detach() finishes by calling scsi_remove_host() to remove the
scsi host associated with the port. This function will trigger the
removal of all scsi devices attached to the host and in the case of
disks, calls to sd_shutdown() which will flush the device write cache
and stop the device. However, given that the devices were already
disabled by ata_eh_unload(), the synchronize write cache command and
start stop unit commands fail. E.g. running "rmmod ahci" with first
removing sd_mod results in error messages like:
ata13.00: disable device
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] Stopping disk
sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
Fix this by removing all scsi devices of the ata devices connected to
the port before scheduling libata EH to disable the ATA devices.
Fixes: 720ba12620ee ("[PATCH] libata-hp: update unload-unplug")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function ata_port_request_pm() checks the port flag
ATA_PFLAG_PM_PENDING and calls ata_port_wait_eh() if this flag is set to
ensure that power management operations for a port are not scheduled
simultaneously. However, this flag check is done without holding the
port lock.
Fix this by taking the port lock on entry to the function and checking
the flag under this lock. The lock is released and re-taken if
ata_port_wait_eh() needs to be called. The two WARN_ON() macros checking
that the ATA_PFLAG_PM_PENDING flag was cleared are removed as the first
call is racy and the second one done without holding the port lock.
Fixes: 5ef41082912b ("ata: add ata port system PM callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A single fix for libata: older devices don't support command duration
limits (CDL) and some don't support report opcodes, meaning there's no
way to tell if they support the command or not.
Reduce the problems of incorrectly using CDL commands on older devices
by checking SCSI spec compliance at SPC-5 (the spec which introduced
the command) before turning on CDL"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: ata: Do no try to probe for CDL on old drives
|
|
For REPORT SUPPORTED OPERATION CODES command, the service action field is
defined as bits 0-4 in the second byte in the CDB. Bits 5-7 in the second
byte are reserved.
Only look at the service action field in the second byte when determining
if the MAINTENANCE IN opcode is a REPORT SUPPORTED OPERATION CODES command.
This matches how we only look at the service action field in the second
byte when determining if the SERVICE ACTION IN(16) opcode is a READ
CAPACITY(16) command (reserved bits 5-7 in the second byte are ignored).
Fixes: 7b2030942859 ("libata: Add support for SCT Write Same")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Some old drives (e.g. an Ultra320 SCSI disk as reported by John) do not
seem to execute MAINTENANCE_IN / MI_REPORT_SUPPORTED_OPERATION_CODES
commands correctly and hang when a non-zero service action is specified
(one command format with service action case in scsi_report_opcode()).
Currently, CDL probing with scsi_cdl_check_cmd() is the only caller using a
non zero service action for scsi_report_opcode(). To avoid issues with
these old drives, do not attempt CDL probe if the device reports support
for an SPC version lower than 5 (CDL was introduced in SPC-5). To keep
things working with ATA devices which probe for the CDL T2A and T2B pages
introduced with SPC-6, modify ata_scsiop_inq_std() to claim SPC-6 version
compatibility for ATA drives supporting CDL.
SPC-6 standard version number is defined as Dh (= 13) in SPC-6 r09. Fix
scsi_probe_lun() to correctly capture this value by changing the bit mask
for the second byte of the INQUIRY response from 0x7 to 0xf.
include/scsi/scsi.h is modified to add the definition SCSI_SPC_6 with the
value 14 (Dh + 1). The missing definitions for the SCSI_SPC_4 and
SCSI_SPC_5 versions are also added.
Reported-by: John David Anglin <dave.anglin@bell.net>
Fixes: 624885209f31 ("scsi: core: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230915022034.678121-1-dlemoal@kernel.org
Tested-by: David Gow <david@davidgow.net>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, we fetch sense data for a _successful_ command if either:
1) Command was NCQ and ATA_DFLAG_CDL_ENABLED flag set (flag
ATA_DFLAG_CDL_ENABLED will only be set if the Successful NCQ command
sense data supported bit is set); or
2) Command was non-NCQ and regular sense data reporting is enabled.
This means that case 2) will trigger for a non-NCQ command which has
ATA_SENSE bit set, regardless if CDL is enabled or not.
This decision was by design. If the device reports that it has sense data
available, it makes sense to fetch that sense data, since the sk/asc/ascq
could be important information regardless if CDL is enabled or not.
However, the fetching of sense data for a successful command is done via
ATA EH. Considering how intricate the ATA EH is, we really do not want to
invoke ATA EH unless absolutely needed.
Before commit 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL
commands using policy 0xD") we never fetched sense data for successful
commands.
In order to not invoke the ATA EH unless absolutely necessary, even if the
device claims support for sense data reporting, only fetch sense data for
successful (NCQ and non-NCQ commands) commands that are using CDL.
[Damien] Modified the check to test the qc flag ATA_QCFLAG_HAS_CDL
instead of the device support for CDL, which is implied for commands
using CDL.
Fixes: 3ac873c76d79 ("ata: libata-core: fix when to fetch sense data for successful commands")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
commit 1e641060c4b5 ("libata: clear eh_info on reset completion") added
a workaround that broke the retry mechanism in ATA EH.
Tejun himself suggested to remove this workaround when it was identified
to cause additional problems:
https://lore.kernel.org/linux-ide/20110426135027.GI878@htj.dyndns.org/
He even said:
"Hmm... it seems I wasn't thinking straight when I added that work around."
https://lore.kernel.org/linux-ide/20110426155229.GM878@htj.dyndns.org/
While removing the workaround solved the issue, however, the workaround was
kept to avoid "spurious hotplug events during reset", and instead another
workaround was added on top of the existing workaround in commit
8c56cacc724c ("libata: fix unexpectedly frozen port after ata_eh_reset()").
Because these IRQs happened when the port was frozen, we know that they
were actually a side effect of PxIS and IS.IPS(x) not being cleared before
the COMRESET. This is now done in commit 94152042eaa9 ("ata: libahci: clear
pending interrupt status"), so these workarounds can now be removed.
Since commit 1e641060c4b5 ("libata: clear eh_info on reset completion") has
now been reverted, the ATA EH retry mechanism is functional again, so there
is once again no need to thaw the port more than once in ata_eh_reset().
This reverts "the workaround on top of the workaround" introduced in commit
8c56cacc724c ("libata: fix unexpectedly frozen port after ata_eh_reset()").
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
ata_scsi_port_error_handler() starts off by clearing ATA_PFLAG_EH_PENDING,
before calling ap->ops->error_handler() (without holding the ap->lock).
If an error IRQ is received while ap->ops->error_handler() is running,
the irq handler will set ATA_PFLAG_EH_PENDING.
Once ap->ops->error_handler() returns, ata_scsi_port_error_handler()
checks if ATA_PFLAG_EH_PENDING is set, and if it is, another iteration
of ATA EH is performed.
The problem is that ATA_PFLAG_EH_PENDING is not only cleared by
ata_scsi_port_error_handler(), it is also cleared by ata_eh_reset().
ata_eh_reset() is called by ap->ops->error_handler(). This additional
clearing done by ata_eh_reset() breaks the whole retry logic in
ata_scsi_port_error_handler(). Thus, if an error IRQ is received while
ap->ops->error_handler() is running, the port will currently remain
frozen and will never get re-enabled.
The additional clearing in ata_eh_reset() was introduced in commit
1e641060c4b5 ("libata: clear eh_info on reset completion").
Looking at the original error report:
https://marc.info/?l=linux-ide&m=124765325828495&w=2
We can see the following happening:
[ 1.074659] ata3: XXX port freeze
[ 1.074700] ata3: XXX hardresetting link, stopping engine
[ 1.074746] ata3: XXX flipping SControl
[ 1.411471] ata3: XXX irq_stat=400040 CONN|PHY
[ 1.411475] ata3: XXX port freeze
[ 1.420049] ata3: XXX starting engine
[ 1.420096] ata3: XXX rc=0, class=1
[ 1.420142] ata3: XXX clearing IRQs for thawing
[ 1.420188] ata3: XXX port thawed
[ 1.420234] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
We are not supposed to be able to receive an error IRQ while the port is
frozen (PxIE is set to 0, i.e. all IRQs for the port are disabled).
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) states:
"Each bit location can be thought of as reporting a '1' if the virtual
"interrupt line" for that port is indicating it wishes to generate an
interrupt. That is, if a port has one or more interrupt status bit set,
and the enables for those status bits are set, then this bit shall be set."
Additionally, AHCI state P:ComInit clearly shows that the state machine
will only jump to P:ComInitSetIS (which sets IS.IPS(x) to '1'), if PxIE.PCE
is set to '1'. In our case, PxIE is set to 0, so IS.IPS(x) won't get set.
So IS.IPS(x) only gets set if PxIS and PxIE is set.
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) also states:
"The bits in this register are read/write clear. It is set by the level of
the virtual interrupt line being a set, and cleared by a write of '1' from
the software."
So if IS.IPS(x) is set, you need to explicitly clear it by writing a 1 to
IS.IPS(x) for that port.
Since PxIE is cleared, the only way to get an interrupt while the port is
frozen, is if IS.IPS(x) is set, and the only way IS.IPS(x) can be set when
the port is frozen, is if it was set before the port was frozen.
However, since commit 737dd811a3db ("ata: libahci: clear pending interrupt
status"), we clear both PxIS and IS.IPS(x) after freezing the port, but
before the COMRESET, so the problem that commit 1e641060c4b5 ("libata:
clear eh_info on reset completion") fixed can no longer happen.
Thus, revert commit 1e641060c4b5 ("libata: clear eh_info on reset
completion"), so that the retry logic in ata_scsi_port_error_handler()
works once again. (The retry logic is still needed, since we can still
get an error IRQ _after_ the port has been thawed, but before
ata_scsi_port_error_handler() takes the ap->lock in order to check
if ATA_PFLAG_EH_PENDING is set.)
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Fix indentation and other code style issues in the comm.c file.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309150646.n3iBvbPj-lkp@intel.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
