| Age | Commit message (Collapse) | Author |
|---|
|
When booting a arm 32-bit kernel with config CONFIG_AHCI_DWC enabled on
a am57xx-evm board. This happens when the clock references are unnamed
in DT, the strcmp() produces a NULL pointer dereference, see the
following oops, NULL pointer dereference:
[ 4.673950] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 4.682098] [00000000] *pgd=00000000
[ 4.685699] Internal error: Oops: 5 [#1] SMP ARM
[ 4.690338] Modules linked in:
[ 4.693420] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc7 #1
[ 4.699615] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 4.705749] PC is at strcmp+0x0/0x34
[ 4.709350] LR is at ahci_platform_find_clk+0x3c/0x5c
[ 4.714416] pc : [<c130c494>] lr : [<c0c230e0>] psr: 20000013
[ 4.720703] sp : f000dda8 ip : 00000001 fp : c29b1840
[ 4.725952] r10: 00000020 r9 : c1b23380 r8 : c1b23368
[ 4.731201] r7 : c1ab4cc4 r6 : 00000001 r5 : c3c66040 r4 : 00000000
[ 4.737762] r3 : 00000080 r2 : 00000080 r1 : c1ab4cc4 r0 : 00000000
[...]
[ 4.998870] strcmp from ahci_platform_find_clk+0x3c/0x5c
[ 5.004302] ahci_platform_find_clk from ahci_dwc_probe+0x1f0/0x54c
[ 5.010589] ahci_dwc_probe from platform_probe+0x64/0xc0
[ 5.016021] platform_probe from really_probe+0xe8/0x41c
[ 5.021362] really_probe from __driver_probe_device+0xa4/0x204
[ 5.027313] __driver_probe_device from driver_probe_device+0x38/0xc8
[ 5.033782] driver_probe_device from __driver_attach+0xb4/0x1ec
[ 5.039825] __driver_attach from bus_for_each_dev+0x78/0xb8
[ 5.045532] bus_for_each_dev from bus_add_driver+0x17c/0x220
[ 5.051300] bus_add_driver from driver_register+0x90/0x124
[ 5.056915] driver_register from do_one_initcall+0x48/0x1e8
[ 5.062591] do_one_initcall from kernel_init_freeable+0x1cc/0x234
[ 5.068817] kernel_init_freeable from kernel_init+0x20/0x13c
[ 5.074584] kernel_init from ret_from_fork+0x14/0x2c
[ 5.079681] Exception stack(0xf000dfb0 to 0xf000dff8)
[ 5.084747] dfa0: 00000000 00000000 00000000 00000000
[ 5.092956] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5.101165] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 5.107818] Code: e5e32001 e3520000 1afffffb e12fff1e (e4d03001)
[ 5.114013] ---[ end trace 0000000000000000 ]---
Add an extra check in the if-statement if hpriv-clks[i].id.
Fixes: 6ce73f3a6fc0 ("ata: libahci_platform: Add function returning a clock-handle by id")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
While the ATA specification states that a device should return command
aborted for all commands queued after the device has entered error state,
since ATA only keeps the sense data for the latest command (in non-NCQ
case), we really don't want to send block layer commands to the device
after it has entered error state. (Only ATA EH commands should be sent,
to read the sense data etc.)
Currently, scsi_queue_rq() will check if scsi_host_in_recovery()
(state is SHOST_RECOVERY), and if so, it will _not_ issue a command via:
scsi_dispatch_cmd() -> host->hostt->queuecommand() (ata_scsi_queuecmd())
-> __ata_scsi_queuecmd() -> ata_scsi_translate() -> ata_qc_issue()
Before commit e494f6a72839 ("[SCSI] improved eh timeout handler"),
when receiving a TFES error IRQ, the call chain looked like this:
ahci_error_intr() -> ata_port_abort() -> ata_do_link_abort() ->
ata_qc_complete() -> ata_qc_schedule_eh() -> blk_abort_request() ->
blk_rq_timed_out() -> q->rq_timed_out_fn() (scsi_times_out()) ->
scsi_eh_scmd_add() -> scsi_host_set_state(shost, SHOST_RECOVERY)
Which meant that as soon as an error IRQ was serviced, SHOST_RECOVERY
would be set.
However, after commit e494f6a72839 ("[SCSI] improved eh timeout handler"),
scsi_times_out() will instead call scsi_abort_command() which will queue
delayed work, and the worker function scmd_eh_abort_handler() will call
scsi_eh_scmd_add(), which calls scsi_host_set_state(shost, SHOST_RECOVERY).
So now, after the TFES error IRQ has been serviced, we need to wait for
the SCSI workqueue to run its work before SHOST_RECOVERY gets set.
It is worth noting that, even before commit e494f6a72839 ("[SCSI] improved
eh timeout handler"), we could receive an error IRQ from the time when
scsi_queue_rq() checks scsi_host_in_recovery(), to the time when
ata_scsi_queuecmd() is actually called.
In order to handle both the delayed setting of SHOST_RECOVERY and the
window where we can receive an error IRQ, add a check against
ATA_PFLAG_EH_PENDING (which gets set when servicing the error IRQ),
inside ata_scsi_queuecmd() itself, while holding the ap->lock.
(Since the ap->lock is held while servicing IRQs.)
Fixes: e494f6a72839 ("[SCSI] improved eh timeout handler")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
In ata_tdev_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 13 PID: 13603 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #36
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x3a0
lr : device_del+0x44/0x3a0
Call trace:
device_del+0x48/0x3a0
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tdev_delete+0x24/0x50 [libata]
ata_tlink_delete+0x40/0xa0 [libata]
ata_tport_delete+0x2c/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tdev_add(). In the error path, device_del() is called to delete
the device which was added earlier in this function, and ata_tdev_free()
is called to free ata_dev.
Fixes: d9027470b886 ("[libata] Add ATA transport class")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
In ata_tlink_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 33 PID: 13850 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #12
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x39c
lr : device_del+0x44/0x39c
Call trace:
device_del+0x48/0x39c
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tlink_delete+0x88/0xb0 [libata]
ata_tport_delete+0x2c/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tlink_add().
Fixes: d9027470b886 ("[libata] Add ATA transport class")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
In ata_tport_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 12 PID: 13605 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #8
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x39c
lr : device_del+0x44/0x39c
Call trace:
device_del+0x48/0x39c
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tport_delete+0x34/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tport_add().
Fixes: d9027470b886 ("[libata] Add ATA transport class")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
In the error path in ata_tport_add(), when calling put_device(),
ata_tport_release() is called, it will put the refcount of 'ap->host'.
And then ata_host_put() is called again, the refcount is decreased
to 0, ata_host_release() is called, all ports are freed and set to
null.
When unbinding the device after failure, ata_host_stop() is called
to release the resources, it leads a null-ptr-deref(), because all
the ports all freed and null.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
CPU: 7 PID: 18671 Comm: modprobe Kdump: loaded Tainted: G E 6.1.0-rc3+ #8
pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ata_host_stop+0x3c/0x84 [libata]
lr : release_nodes+0x64/0xd0
Call trace:
ata_host_stop+0x3c/0x84 [libata]
release_nodes+0x64/0xd0
devres_release_all+0xbc/0x1b0
device_unbind_cleanup+0x20/0x70
really_probe+0x158/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0xb4/0x220
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x40
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__pci_register_driver+0x4c/0x60
ahci_pci_driver_init+0x30/0x1000 [ahci]
Fix this by removing redundant ata_host_put() in the error path.
Fixes: 2623c7a5f279 ("libata: add refcounting to ata_host")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
SAT SCSI/ATA Translation specification requires SCSI SYNCHRONIZE CACHE
(10) and (16) commands both shall be translated to ATA flush command.
Also, ZBC Zoned Block Commands specification mandates SYNCHRONIZE CACHE
(16) command support. However, libata translates only SYNCHRONIZE CACHE
(10). This results in SYNCHRONIZE CACHE (16) command failures on SATA
drives and then libata translation does not conform to ZBC. To avoid the
failure, add support for SYNCHRONIZE CACHE (16).
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
If devm_platform_ioremap_resource() fails, it never return
NULL pointer, replace the check with IS_ERR().
Fixes: 57bf0f5a162d ("ARM: pxa: use pdev resource for palmld mmio")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Clang gives a warning when compiling pata_legacy.c with 'make W=1' about
the 'rt' local variable in pdc20230_set_piomode() being set but unused.
Quite obviously, there is an outb() call missing to write back the updated
variable. Moreover, checking the docs by Petr Soucek revealed that bitwise
AND should have been done with a negated timing mask and the master/slave
timing masks were swapped while updating...
Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.")
Reported-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_qoriq.c:283:22: error: cast to smaller integer type
'enum ahci_qoriq_type' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
qoriq_priv->type = (enum ahci_qoriq_type)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_id->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_imx.c:1070:18: error: cast to smaller integer type
'enum ahci_imx_type' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
imxpriv->type = (enum ahci_imx_type)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_id->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_xgene.c:788:14: error: cast to smaller integer type
'enum xgene_ahci_version' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
version = (enum xgene_ahci_version) of_devid->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_devid->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_brcm.c:451:18: error: cast to smaller integer type
'enum brcm_ahci_version' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
priv->version = (enum brcm_ahci_version)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_id->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
When compiling with clang and W=1, the following warning is generated:
drivers/ata/sata_rcar.c:878:15: error: cast to smaller integer type
'enum sata_rcar_type' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
priv->type = (enum sata_rcar_type)of_device_get_match_data(dev);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size returned by of_device_get_match_data().
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
|
|
If CONFIG_OF is disabled and the ahci_st driver is builtin (or
CONFIG_MODULES is disabled), then using the macro of_match_ptr()
results in the st_ahci_match variable being unused, which generates a
compilation warning and a compilation error if CONFIG_WERROR is enabled.
Fix this by directly assigning st_ahci_match to .of_match_table in the
st_ahci_driver platform driver definition.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
UBSAN complains about array-index-out-of-bounds:
[ 1.980703] kernel: UBSAN: array-index-out-of-bounds in /build/linux-9H675w/linux-5.15.0/drivers/ata/libahci.c:968:41
[ 1.980709] kernel: index 15 is out of range for type 'ahci_em_priv [8]'
[ 1.980713] kernel: CPU: 0 PID: 209 Comm: scsi_eh_8 Not tainted 5.15.0-25-generic #25-Ubuntu
[ 1.980716] kernel: Hardware name: System manufacturer System Product Name/P5Q3, BIOS 1102 06/11/2010
[ 1.980718] kernel: Call Trace:
[ 1.980721] kernel: <TASK>
[ 1.980723] kernel: show_stack+0x52/0x58
[ 1.980729] kernel: dump_stack_lvl+0x4a/0x5f
[ 1.980734] kernel: dump_stack+0x10/0x12
[ 1.980736] kernel: ubsan_epilogue+0x9/0x45
[ 1.980739] kernel: __ubsan_handle_out_of_bounds.cold+0x44/0x49
[ 1.980742] kernel: ahci_qc_issue+0x166/0x170 [libahci]
[ 1.980748] kernel: ata_qc_issue+0x135/0x240
[ 1.980752] kernel: ata_exec_internal_sg+0x2c4/0x580
[ 1.980754] kernel: ? vprintk_default+0x1d/0x20
[ 1.980759] kernel: ata_exec_internal+0x67/0xa0
[ 1.980762] kernel: sata_pmp_read+0x8d/0xc0
[ 1.980765] kernel: sata_pmp_read_gscr+0x3c/0x90
[ 1.980768] kernel: sata_pmp_attach+0x8b/0x310
[ 1.980771] kernel: ata_eh_revalidate_and_attach+0x28c/0x4b0
[ 1.980775] kernel: ata_eh_recover+0x6b6/0xb30
[ 1.980778] kernel: ? ahci_do_hardreset+0x180/0x180 [libahci]
[ 1.980783] kernel: ? ahci_stop_engine+0xb0/0xb0 [libahci]
[ 1.980787] kernel: ? ahci_do_softreset+0x290/0x290 [libahci]
[ 1.980792] kernel: ? trace_event_raw_event_ata_eh_link_autopsy_qc+0xe0/0xe0
[ 1.980795] kernel: sata_pmp_eh_recover.isra.0+0x214/0x560
[ 1.980799] kernel: sata_pmp_error_handler+0x23/0x40
[ 1.980802] kernel: ahci_error_handler+0x43/0x80 [libahci]
[ 1.980806] kernel: ata_scsi_port_error_handler+0x2b1/0x600
[ 1.980810] kernel: ata_scsi_error+0x9c/0xd0
[ 1.980813] kernel: scsi_error_handler+0xa1/0x180
[ 1.980817] kernel: ? scsi_unjam_host+0x1c0/0x1c0
[ 1.980820] kernel: kthread+0x12a/0x150
[ 1.980823] kernel: ? set_kthread_struct+0x50/0x50
[ 1.980826] kernel: ret_from_fork+0x22/0x30
[ 1.980831] kernel: </TASK>
This happens because sata_pmp_init_links() initialize link->pmp up to
SATA_PMP_MAX_PORTS while em_priv is declared as 8 elements array.
I can't find the maximum Enclosure Management ports specified in AHCI
spec v1.3.1, but "12.2.1 LED message type" states that "Port Multiplier
Information" can utilize 4 bits, which implies it can support up to 16
ports. Hence, use SATA_PMP_MAX_PORTS as EM_MAX_SLOTS to resolve the
issue.
BugLink: https://bugs.launchpad.net/bugs/1970074
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
'ahci:' is an invalid prefix, preventing the module from autoloading.
Fix this by using the 'platform:' prefix and DRV_NAME.
Fixes: 9e54eae23bc9 ("ahci_imx: add ahci sata support on imx platforms")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Print the timeout value for internal command failures due to a
timeout (from Tomas)
- Improve parameter names in ata_dev_set_feature() to clarify this
function use (from Niklas)
- Improve the ahci driver low power mode setting initialization to
allow more flexibility for the user (from Rafael)
- Several patches to remove redundant variables in libata-core,
libata-eh and the pata_macio driver and to fix typos in comments
(from Jinpeng, Shaomin, Ye)
- Some code simplifications and macro renaming (for clarity) in various
functions of libata-core (from me)
- Add a missing check for a potential failure of sata_scr_read() in
sata_print_link_status() (from Li)
- Cleanup of libata Kconfig PATA_PLATFORM and PATA_OF_PLATFORM options
(from Lukas)
- Cleanups of ata dt-bindings and improvements of libahci_platform,
ahci and libahci code (from Serge)
- New driver for Synopsys AHCI SATA controllers, based of the generic
ahci code (from Serge). One compilation warning fix is added for this
driver (from me)
- Several fixes to macros used to discover a drive capabilities to be
consistent with the ACS specifications (from Niklas)
- A couple of simplifcations to some libata functions, removing
unnecessary arguments (from Niklas)
- An improvements to libata-eh code to avoid unnecessary link reset
when revalidating a drive after a failed command. In practice, this
extra, unneeded reset, reset does not cause any arm beyond slightly
slowing down error recovery (from Niklas)
* tag 'ata-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (45 commits)
ata: libata-eh: avoid needless hard reset when revalidating link
ata: libata: drop superfluous ata_eh_analyze_tf() parameter
ata: libata: drop superfluous ata_eh_request_sense() parameter
ata: fix ata_id_has_dipm()
ata: fix ata_id_has_ncq_autosense()
ata: fix ata_id_has_devslp()
ata: fix ata_id_sense_reporting_enabled() and ata_id_has_sense_reporting()
ata: libata-eh: Remove the unneeded result variable
ata: ahci_st: Enable compile test
ata: ahci_st: Fix compilation warning
MAINTAINERS: Add maintainers for DWC AHCI SATA driver
ata: ahci-dwc: Add Baikal-T1 AHCI SATA interface support
ata: ahci-dwc: Add platform-specific quirks support
dt-bindings: ata: ahci: Add Baikal-T1 AHCI SATA controller DT schema
ata: ahci: Add DWC AHCI SATA controller support
ata: libahci_platform: Add function returning a clock-handle by id
dt-bindings: ata: ahci: Add DWC AHCI SATA controller DT schema
ata: ahci: Introduce firmware-specific caps initialization
ata: ahci: Convert __ahci_port_base to accepting hpriv as arguments
ata: libahci: Don't read AHCI version twice in the save-config method
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"The most significant part of this update is the thermal control DT
initialization rework from Daniel Lezcano and the following conversion
of drivers to use the new API introduced by it
Apart from that, the maximum number of trip points in a thermal zone
is increased and there are some fixes and code cleanups
Specifics:
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after free
when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar)
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang)
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing)
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada)
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki)
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan)
- Drop redundant error message from da9062-thermal (zhaoxiao)
- Drop of_match_ptr() from thermal_mmio (Jean Delvare)"
* tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: core: Increase maximum number of trip points
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: Drop duplicate words from comments
thermal: move from strlcpy() with unused retval to strscpy()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
...
|
|
The function __ata_change_queue_depth() uses the helper
ata_scsi_find_dev() to get the ata_device structure of a scsi device and
set that device maximum queue depth. However, when the ata device is
managed by libsas, ata_scsi_find_dev() returns NULL, turning
__ata_change_queue_depth() into a nop, which prevents the user from
setting the maximum queue depth of ATA devices used with libsas based
HBAs.
Fix this by renaming __ata_change_queue_depth() to
ata_change_queue_depth() and adding a pointer to the ata_device
structure of the target device as argument. This pointer is provided by
ata_scsi_change_queue_depth() using ata_scsi_find_dev() in the case of
a libata managed device and by sas_change_queue_depth() using
sas_to_ata_dev() in the case of a libsas managed ata device.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: John Garry <john.garry@huawei.com>
|
|
For SATA devices supporting NCQ, drivers using libsas first initialize a
scsi device queue depth based on the controller and device capabilities,
leading to the scsi device queue_depth field being 32 (ATA maximum queue
depth) for most setup. However, if libata was loaded using the
force=[ID]]noncq argument, the default queue depth should be set to 1 to
reflect the fact that queuable commands will never be used. This is
consistent with manually setting a device queue depth to 1 through sysfs
as that disables NCQ use for the device.
Fix ata_scsi_dev_config() to honor the noncq parameter by sertting the
device queue depth to 1 for devices that do not have the ATA_DFLAG_NCQ
flag set.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: John Garry <john.garry@huawei.com>
|
|
Commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).
The board_ahci_low_power configuration enables support for low power
modes.
This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.
Therefore, when commit 1527f69204fe ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.
The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.
Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.
Fixes: 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Performing a revalidation on a AHCI controller supporting LPM,
while using a lpm mode of e.g. med_power_with_dip (hipm + dipm) or
medium_power (hipm), will currently always lead to a hard reset.
The expected behavior is that a hard reset is only performed when
revalidate fails, because the properties of the drive has changed.
A revalidate performed after e.g. a NCQ error, or such a simple thing
as disabling write-caching (hdparm -W 0 /dev/sda), should succeed on
the first try (and should therefore not cause the link to be reset).
This unwarranted hard reset happens because ata_phys_link_offline()
returns true for a link that is in deep sleep. Thus the call to
ata_phys_link_offline() in ata_eh_revalidate_and_attach() will cause
the revalidation to fail, which causes ata_eh_handle_dev_fail() to be
called, which will set ehc->i.action |= ATA_EH_RESET, such that the
link is reset before retrying revalidation.
When the link is reset, the link is reestablished, so when
ata_eh_revalidate_and_attach() is called the second time, directly
after the link has been reset, ata_phys_link_offline() will return
false, and the revalidation will succeed.
Looking at "8.3.1.3 HBA Initiated" in the AHCI 1.3.1 specification,
it is clear the when host software writes a new command to memory,
by setting a bit in the PxCI/PxSACT HBA port registers, the HBA will
automatically bring back the link before sending out the Command FIS.
However, simply reading a SCR (like ata_phys_link_offline() does),
will not cause the HBA to automatically bring back the link.
As long as hipm is enabled, the HBA will put an idle link into deep
sleep. Avoid this needless hard reset on revalidation by temporarily
disabling hipm, by setting the LPM mode to ATA_LPM_MAX_POWER.
After revalidation is complete, ata_eh_recover() will restore the link
policy by setting the LPM mode to ap->target_lpm_policy.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The parameter can easily be derived from struct ata_queued_cmd.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The parameter can easily be derived from struct ata_queued_cmd.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Return the value ata_port_abort() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Enable compiling the ahci_st driver when COMPILE_TEST is enabled.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Remove the unused variable dev in st_ahci_probe() to avoid compilation
warning and build failures where CONFIG_WERROR is enabled.
Fixes: 3f74cd046fbe ("ata: libahci_platform: Parse ports-implemented property in resources getter")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
It's almost fully compatible DWC AHCI SATA IP-core derivative except the
reference clocks source, which need to be very carefully selected. In
particular the DWC AHCI SATA PHY can be clocked either from the pads
ref_pad_clk_{m,p} or from the internal wires ref_alt_clk_{m,n}. In the
later case the clock signal is generated from the Baikal-T1 CCU SATA PLL.
The clocks source is selected by means of the ref_use_pad wire connected
to the CCU SATA reference clock CSR.
In normal situation it would be much more handy to use the internal
reference clock source, but alas we haven't managed to make the AHCI
controller working well with it so far. So it's preferable to have the
controller clocked from the external clock generator and fallback to the
internal clock source only as a last resort. Other than that the
controller is full compatible with the DWC AHCI SATA IP-core.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Some DWC AHCI SATA IP-core derivatives require to perform small platform
or IP-core specific setups. They are too small to be placed in a dedicated
driver. It's just much easier to have a set of quirks for them right in
the DWC AHCI driver code. Since we are about to add such platform support,
as a pre-requisite we introduce a platform-data based DWC AHCI quirks API.
The platform data can be used to define the flags passed to the
ahci_platform_get_resources() method, additional AHCI host-flags and a set
of callbacks to initialize, re-initialize and clear the platform settings.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Synopsys AHCI SATA controller can work pretty under with the generic
AHCI-platform driver control. But there are vendor-specific peculiarities
which can tune the device performance up and which may need to be fixed up
for proper device functioning. In addition some DWC AHCI-based controllers
may require small platform-specific fixups, so adding them in the generic
AHCI driver would have ruined the code simplicity. Shortly speaking in
order to keep the generic AHCI-platform code clean and have DWC AHCI
SATA-specific features supported we suggest to add a dedicated DWC AHCI
SATA device driver. Aside with the standard AHCI-platform resources
getting, enabling/disabling and the controller registration the new driver
performs the next actions.
First of all there is a way to verify whether the HBA/ports capabilities
activated in OF are correct. Almost all features availability is reflected
in the vendor-specific parameters registers. So the DWC AHCI driver does
the capabilities sanity check based on the corresponding fields state.
Secondly if either the Command Completion Coalescing or the Device Sleep
feature is enabled the DWC AHCI-specific internal 1ms timer must be fixed
in accordance with the application clock signal frequency. In particular
the timer value must be set to be Fapp * 1000. Normally the SoC designers
pre-configure the TIMER1MS register to contain a correct value by default.
But the platforms can support the application clock rate change. If that
happens the 1ms timer value must be accordingly updated otherwise the
dependent features won't work as expected. In the DWC AHCI driver we
suggest to rely on the "aclk" reference clock rate to set the timer
interval up. That clock source is supposed to be the AHCI SATA application
clock in accordance with the DT bindings.
Finally DWC AHCI SATA controller AXI/AHB bus DMA-engine can be tuned up to
transfer up to 1024 * FIFO words at a time by setting the Tx/Rx
transaction size in the DMA control register. The maximum value depends on
the DMA data bus and AXI/AHB bus maximum burst length. In most of the
cases it's better to set the maximum possible value to reach the best AHCI
SATA controller performance. But sometimes in order to improve the system
interconnect responsiveness, transferring in smaller data chunks may be
more preferable. For such cases and for the case when the default value
doesn't provide the best DMA bus performance we suggest to use the new
HBA-port specific DT-properties "snps,{tx,rx}-ts-max" to tune the DMA
transactions size up.
After all the settings denoted above are handled the DWC AHCI SATA driver
proceeds further with the standard AHCI-platform host initializations.
Note since DWC AHCI controller is now have a dedicated driver we can
discard the corresponding compatible string from the ahci-platform.c
module. The same concerns "snps,spear-ahci" compatible string, which is
also based on the DWC AHCI IP-core.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Since all the clocks are retrieved by the method
ahci_platform_get_resources() there is no need for the LLD (glue) drivers
to be looking for some particular of them in the kernel clocks table
again. Instead we suggest to add a simple method returning a
device-specific clock with passed connection ID if it is managed to be
found. Otherwise the function will return NULL. Thus the glue-drivers
won't need to either manually touching the hpriv->clks array or calling
clk_get()-friends. The AHCI platform drivers will be able to use the new
function right after the ahci_platform_get_resources() method invocation
and up to the device removal.
Note the method is left unused here, but will be utilized in the framework
of the DWC AHCI SATA driver being added in the next commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There are systems with no BIOS or comprehensive embedded firmware which
could be able to properly initialize the SATA AHCI controller
platform-specific capabilities. In that case a good alternative to having
a clever bootloader is to create a device tree node with the properties
well describing all the AHCI-related platform specifics. All the settings
which are normally detected and marked as available in the HBA and its
ports capabilities fields [1] could be defined in the platform DTB by
means of a set of the dedicated properties. Such approach perfectly fits
to the DTB-philosophy - to provide hardware/platform description.
So here we suggest to extend the SATA AHCI device tree bindings with two
additional DT-properties:
1) "hba-cap" - HBA platform generic capabilities like:
- SSS - Staggered Spin-up support.
- SMPS - Mechanical Presence Switch support.
2) "hba-port-cap" - HBA platform port capabilities like:
- HPCP - Hot Plug Capable Port.
- MPSP - Mechanical Presence Switch Attached to Port.
- CPD - Cold Presence Detection.
- ESP - External SATA Port.
- FBSCP - FIS-based Switching Capable Port.
All of these capabilities require to have a corresponding hardware
configuration. Thus it's ok to have them defined in DTB.
Even though the driver currently takes into account the state of the ESP
and FBSCP flags state only, there is nothing wrong with having all of them
supported by the generic AHCI library in order to have a complete OF-based
platform-capabilities initialization procedure. These properties will be
parsed in the ahci_platform_get_resources() method and their values will
be stored in the saved_* fields of the ahci_host_priv structure, which in
its turn then will be used to restore the H.CAP, H.PI and P#.CMD
capability fields on device init and after HBA reset.
Please note this modification concerns the HW-init HBA and its ports flags
only, which are by specification [1] are supposed to be initialized by the
BIOS/platform firmware/expansion ROM and which are normally declared in
the one-time-writable-after-reset register fields. Even though these flags
aren't supposed to be cleared after HBA reset some AHCI instances may
violate that rule so we still need to perform the fields resetting after
each reset. Luckily the corresponding functionality has already been
partly implemented in the framework of the ahci_save_initial_config() and
ahci_restore_initial_config() methods.
[1] Serial ATA AHCI 1.3.1 Specification, p. 103
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The port base address may be required even before the ata_host instance is
initialized and activated, for instance in the ahci_save_initial_config()
method which we are about to update (consider this modification as a
preparation for that one). Seeing the __ahci_port_base() function isn't
used much it's the best candidate to provide the required functionality.
So let's convert it to accepting the ahci_host_priv structure pointer.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There is no point in reading the AHCI version all over in the tail of the
ahci_save_initial_config() method. That register is RO and doesn't change
its value even after reset. So just reuse the data, which has already been
read from there earlier in the head of the function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Currently there are four port-map-related fields declared in the
ahci_host_priv structure and used to setup the HBA ports mapping. First
the ports-mapping is read from the PI register and immediately stored in
the saved_port_map field. If forced_port_map is initialized with non-zero
value then its value will have greater priority over the value read from
PI, thus it will override the saved_port_map field. That value will be
then masked by a non-zero mask_port_map field and after some sanity checks
it will be stored in the ahci_host_priv.port_map field as a final port
mapping.
As you can see the logic is a bit too complicated for such a simple task.
We can freely get rid from at least one of the fields with no change to
the implemented semantic. The force_port_map field can be replaced with
taking non-zero saved_port_map value into account. So if saved_port_map is
pre-initialized by the low level drivers (platform drivers) then it will
have greater priority over the value read from PI register and will be
used as actual HBA ports mapping later on. Thus the ports map forcing task
will be just transferred from force_port_map to the saved_port_map field.
This modification will perfectly fit into the feature of having OF-based
initialization of the HW-init HBA CSR fields we are about to introduce in
the next commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Currently not all of the Port-specific capabilities listed in the
PORT_CMD-enumeration. Let's extend that set with the Cold Presence
Detection and Mechanical Presence Switch attached to the Port flags [1] so
to closeup the set of the platform-specific port-capabilities flags. Note
these flags are supposed to be set by the platform firmware if there is
one. Alternatively as we are about to do they can be set by means of the
OF properties.
While at it replace PORT_IRQ_DEV_ILCK with PORT_IRQ_DMPS and fix the
comment there. In accordance with [2] that IRQ flag is supposed to
indicate the state of the signal coming from the Mechanical Presence
Switch.
[1] Serial ATA AHCI 1.3.1 Specification, p.27
[2] Serial ATA AHCI 1.3.1 Specification, p.24, p.88
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Currently the ACHI-platform library supports only the assert and deassert
reset signals and ignores the platforms with self-deasserting reset lines.
That prone to having the platforms with self-deasserting reset method
misbehaviour when it comes to resuming from sleep state after the clocks
have been fully disabled. For such cases the controller needs to be fully
reset all over after the reference clocks are enabled and stable,
otherwise the controller state machine might be in an undetermined state.
The best solution would be to auto-detect which reset method is supported
by the particular platform and use it implicitly in the framework of the
ahci_platform_enable_resources()/ahci_platform_disable_resources()
methods. Alas it can't be implemented due to the AHCI-platform library
already supporting the shared reset control lines. As [1] says in such
case we have to use only one of the next methods:
+ reset_control_assert()/reset_control_deassert();
+ reset_control_reset()/reset_control_rearm().
If the driver had an exclusive control over the reset lines we could have
been able to manipulate the lines with no much limitation and just used
the combination of the methods above to cover all the possible
reset-control cases. Since the shared reset control has already been
advertised and couldn't be changed with no risk to breaking the platforms
relying on it, we have no choice but to make the platform drivers to
determine which reset methods the platform reset system supports.
In order to implement both types of reset control support we suggest to
introduce the new AHCI-platform flag: AHCI_PLATFORM_RST_TRIGGER, which
when passed to the ahci_platform_get_resources() method together with the
AHCI_PLATFORM_GET_RESETS flag will indicate that the reset lines are
self-deasserting thus the reset_control_reset()/reset_control_rearm() will
be used to control the reset state. Otherwise the
reset_control_deassert()/reset_control_assert() methods will be utilized.
[1] Documentation/driver-api/reset.rst
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The ports-implemented property is mainly used on the OF-based platforms
with no ports mapping initialized by a bootloader/BIOS firmware. Seeing
the same of_property_read_u32()-based pattern has already been implemented
in the generic AHCI LLDD (glue) driver and in the Mediatek, St AHCI
drivers let's move the property read procedure to the generic
ahci_platform_get_resources() method. Thus we'll have the forced ports
mapping feature supported for each OF-based platform which requires that,
and stop re-implementing the same pattern in there a bit simplifying the
code.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical
from the further AHCI-platform initialization point of view since
exceeding the ports upper limit will cause allocating more resources than
will be used afterwards. But detecting too many child DT-nodes doesn't
seem right since it's very unlikely to have it on an ordinary platform. In
accordance with the AHCI specification there can't be more than 32 ports
implemented at least due to having the CAP.NP field of 5 bits wide and the
PI register of dword size. Thus if such situation is found the DTB must
have been corrupted and the data read from it shouldn't be reliable. Let's
consider that as an erroneous situation and halt further resources
allocation.
Note it's logically more correct to have the nports set only after the
initialization value is checked for being sane. So while at it let's make
sure nports is assigned with a correct value.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
In order to simplify the clock-related code there is a way to convert the
current fixed clocks array into using the common bulk clocks kernel API
with dynamic set of the clock handlers and device-managed clock-resource
tracking. It's a bit tricky due to the complication coming from the
requirement to support the platforms (da850, spear13xx) with the
non-OF-based clock source, but still doable.
Before this modification there are two methods have been used to get the
clocks connected to an AHCI device: clk_get() - to get the very first
clock in the list and of_clk_get() - to get the rest of them. Basically
the platforms with non-OF-based clocks definition could specify only a
single reference clock source. The platforms with OF-hw clocks have been
luckier and could setup up to AHCI_MAX_CLKS clocks. Such semantic can be
retained with using devm_clk_bulk_get_all() to retrieve the clocks defined
via the DT firmware and devm_clk_get_optional() otherwise. In both cases
using the device-managed version of the methods will cause the automatic
resources deallocation on the AHCI device removal event. The only
complicated part in the suggested approach is the explicit allocation and
initialization of the clk_bulk_data structure instance for the non-OF
reference clocks. It's required in order to use the Bulk Clocks API for
the both denoted cases of the clocks definition.
Note aside with the clock-related code reduction and natural
simplification, there are several bonuses the suggested modification
provides. First of all the limitation of having no greater than
AHCI_MAX_CLKS clocks is now removed, since the devm_clk_bulk_get_all()
method will allocate as many reference clocks data descriptors as there
are clocks specified for the device. Secondly the clock names are
auto-detected. So the LLDD (glue) drivers can make sure that the required
clocks are specified just by checking the clock IDs in the clk_bulk_data
array. Thirdly using the handy Bulk Clocks kernel API improves the
clocks-handling code readability. And the last but not least this
modification implements a true optional clocks support to the
ahci_platform_get_resources() method. Indeed the previous clocks getting
procedure just stopped getting the clocks on any errors (aside from
non-critical -EPROBE_DEFER) in a way so the callee wasn't even informed
about abnormal loop termination. The new implementation lacks of such
problem. The ahci_platform_get_resources() will return an error code if
the corresponding clocks getting method ends execution abnormally.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Currently the IOMEM AHCI registers space is mapped by means of the
two functions invocation: platform_get_resource() is used to get the very
first memory resource and devm_ioremap_resource() is called to remap that
resource. Device-managed kernel API provides a handy wrapper to perform
the same in single function call: devm_platform_ioremap_resource().
While at it seeing many AHCI platform drivers rely on having the AHCI CSR
space marked with "ahci" name let's first try to find and remap the CSR
IO-mem with that name and only if it fails fallback to getting the very
first registers space platform resource.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
It is currently possible to select "Generic platform device PATA support"
in two situations:
- architecture allows the generic platform device PATA support and
indicates that with "select HAVE_PATA_PLATFORM".
- if the user claims to be an EXPERT by setting CONFIG_EXPERT to yes
However, there is no use case to have Generic platform device PATA support
in a kernel build if the architecture definition, i.e., the selection of
configs by an architecture, does not support it.
If the architecture definition is wrong, i.e., it just misses a 'select
HAVE_PATA_PLATFORM', then even an expert that configures the kernel build
should not just fix that by overruling the claimed support by an
architecture. If the architecture definition is wrong, the expert should
just provide a patch to correct the architecture definition instead---in
the end, if the user is an expert, sending a quick one-line patch should
not be an issue.
In other words, I do not see the deeper why an expert can overrule the
architecture definition in this case, as the expert may not overrule the
config selections defined by the architecture in the large majority
---or probably all other (modulo some mistakes)---of similar cases.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There are two options for platform device PATA support:
PATA_PLATFORM: Generic platform device PATA support
PATA_OF_PLATFORM: OpenFirmware platform device PATA support
If an architecture allows the generic platform device PATA support, it
shall select HAVE_PATA_PLATFORM. Then, Generic platform device PATA support
is available and can be selected.
If an architecture has OpenFirmware support, which it indicates by
selecting OF, OpenFirmware platform device PATA support is available
and can be selected.
If OpenFirmware platform device PATA support is selected, then the
functionality (code files) from Generic platform device PATA support needs
to be integrated in the kernel build for the OpenFirmware platform device
PATA support to work. Select PATA_PLATFORM in PATA_OF_PLATFORM to make sure
the needed files are added in the build.
So, architectures with OpenFirmware support, do not need to additionally
select HAVE_PATA_PLATFORM. It is only needed by architecture that want the
non-OF pata-platform module.
Reflect this way of intended use of config symbols in the ata Kconfig and
adjust all architecture definitions.
This follows the suggestion from Arnd Bergmann (see Link).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/all/4b33bffc-2b6d-46b4-9f1d-d18e55975a5a@www.fastmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
sata_scr_read() could return negative error code on failure. Check the
return value when reading the control register.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Remove the repeated word "Transfer" in comments.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There is unneeded word "to" in line 669, so remove it.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The err_mask variable is not useful. Remove it.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Since ata_build_rw_tf() is only called from ata_scsi_rw_xlat() with the
tf, dev and tag arguments obtained from the queued command structure,
we can simplify the interface of ata_build_rw_tf() by passing directly
the qc structure as argument.
Furthermore, since ata_scsi_rw_xlat() is never used for internal
commands, we can also remove the internal tag check for the NCQ case.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Rename ATA_DFLAG_NCQ_PRIO_ENABLE to ATA_DFLAG_NCQ_PRIO_ENABLED to match
the fact that this flags indicates if NCQ priority use is enabled by the
user.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
