| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixlet from Tejun Heo:
"I merged the two blaclist entries into 'Crucial_CT???M500SSD*'"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: use wider match for blacklisting Crucial M500
|
|
We're now blacklisting "Crucial_CT???M500SSD1" and
"Crucial_CT???M500SSD3". Also, "Micron_M500*" is blacklisted which is
about the same devices as the crucial branded ones. Let's merge the
two Crucial M500 entries and widen the match to
"Crucial_CT???M500SSD*" so that we don't have to fiddle with new
entries for similar devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Just a couple patches blacklisting more broken devices"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (2BA30001)
libata: disable queued TRIM for Crucial M500 mSATA SSDs
|
|
M8 (2BA30001)
Via commit 87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk
for Seagate Momentus SpinPoint M8" we added a quirk for disks named
"ST1000LM024 HN-M101MBB" with firmware revision "2AR10001".
As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901,
we need to also add firmware revision 2BA30001 as it is broken as well.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Queued TRIM commands cause problems and silent file system corruption
on Crucial M500 SSDs. This patch disables them for the mSATA model of
the drive.
Signed-off-by: Marios Andreopoulos <opensource@andmarios.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # 3.12+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71371
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most interesting thing here is the change to enable INTx (by
clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
Apparently the Baytrail BIOS does this, which means EHCI doesn't work.
Also, fix an AHCI MSI regression and other issues with the recent MSI
changes. This also adds pci_enable_msi_exact() and
pci_enable_msix_exact(), which aren't regression fixes, but will keep
us from touching drivers twice (once to stop using the deprecated
pci_enable_msi(), etc., and again to use the *_exact() variants).
There's also a minor MVEBU fix.
Summary:
MSI:
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous:
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"
* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ahci: Fix broken fallback to single MSI mode
PCI: Enable INTx if BIOS left them disabled
PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
PCI/MSI: Fix cut-and-paste errors in documentation
PCI/MSI: Add pci_enable_msi() documentation back
PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
PCI/MSI: Fix leak of msi_attrs
PCI/MSI: Check kmalloc() return value, fix leak of name
PCI: mvebu: Use Device ID and revision from underlying endpoint
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Various device specific fixes. Nothing too interesting"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable NCQ on Samsung pci-e SSDs on macbooks
ata: sata_mv: Cleanup only the initialized ports
sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN
ata: enable quirk from jmicron JMB350 for JMB394
ATA: SATA_MV: Add missing Kconfig select statememnt
ata: pata_imx: Check the return value from clk_prepare_enable()
|
|
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Cc: stable@vger.kernel.org
|
|
When an error occurs in the port initialization loop, currently the
driver tries to cleanup all the ports. This results in a NULL pointer
dereference if the ports were only partially initialized.
Fix this by updating only the number of initialized ports (either
with failure or successfully), before jumping to the error path
and looping over that number in the cleanup loop.
Cc: Andrew Lunn <andrew@lunn.ch>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Commit 7b92b4f61ec4 ("PCI/MSI: Remove pci_enable_msi_block_auto()")
introduced a regression: if multiple MSI initialization fails, the code
falls back to INTx rather than to single MSI.
Fixes: 7b92b4f61ec4 ("PCI/MSI: Remove pci_enable_msi_block_auto()")
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
Make use of devm_phy_optional_get() in order to fix probe failures on
Armada 370, XP and others, when there is no phy driver available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
It's a bit odd to see a newer device showing mod15write; however, the
reported behavior is highly consistent and other factors which could
contribute seem to have been verified well enough. Also, both
sata_sil itself and the drive are fairly outdated at this point making
the risk of this change fairly low. It is possible, probably likely,
that other drive models in the same family have the same problem;
however, for now, let's just add the specific model which was tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: matson <lists-matsonpa@luxsci.me>
References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com
Cc: stable@vger.kernel.org
|
|
Without the patch the kernel generates the following error.
ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123'
ata11.15: PMP revalidation failed (errno=-19)
ata11.15: failed to recover PMP after 5 tries, giving up
This patch helps to bypass this error and the device becomes
functional.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Cc: stable@vger.kernel.org
|
|
SATA_MV depends on GENERIC_PHY. So if SATA_MV is built in, GENERIC_PHY
cannot be modular. Fixes build error found by kbuild test robot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v3.14 merge window:
Resource management
- Change pci_bus_region addresses to dma_addr_t (Bjorn Helgaas)
- Support 64-bit AGP BARs (Bjorn Helgaas, Yinghai Lu)
- Add pci_bus_address() to get bus address of a BAR (Bjorn Helgaas)
- Use pci_resource_start() for CPU address of AGP BARs (Bjorn Helgaas)
- Enforce bus address limits in resource allocation (Yinghai Lu)
- Allocate 64-bit BARs above 4G when possible (Yinghai Lu)
- Convert pcibios_resource_to_bus() to take pci_bus, not pci_dev (Yinghai Lu)
PCI device hotplug
- Major rescan/remove locking update (Rafael J. Wysocki)
- Make ioapic builtin only (not modular) (Yinghai Lu)
- Fix release/free issues (Yinghai Lu)
- Clean up pciehp (Bjorn Helgaas)
- Announce pciehp slot info during enumeration (Bjorn Helgaas)
MSI
- Add pci_msi_vec_count(), pci_msix_vec_count() (Alexander Gordeev)
- Add pci_enable_msi_range(), pci_enable_msix_range() (Alexander Gordeev)
- Deprecate "tri-state" interfaces: fail/success/fail+info (Alexander Gordeev)
- Export MSI mode using attributes, not kobjects (Greg Kroah-Hartman)
- Drop "irq" param from *_restore_msi_irqs() (DuanZhenzhong)
SR-IOV
- Clear NumVFs when disabling SR-IOV in sriov_init() (ethan.zhao)
Virtualization
- Add support for save/restore of extended capabilities (Alex Williamson)
- Add Virtual Channel to save/restore support (Alex Williamson)
- Never treat a VF as a multifunction device (Alex Williamson)
- Add pci_try_reset_function(), et al (Alex Williamson)
AER
- Ignore non-PCIe error sources (Betty Dall)
- Support ACPI HEST error sources for domains other than 0 (Betty Dall)
- Consolidate HEST error source parsers (Bjorn Helgaas)
- Add a TLP header print helper (Borislav Petkov)
Freescale i.MX6
- Remove unnecessary code (Fabio Estevam)
- Make reset-gpio optional (Marek Vasut)
- Report "link up" only after link training completes (Marek Vasut)
- Start link in Gen1 before negotiating for Gen2 mode (Marek Vasut)
- Fix PCIe startup code (Richard Zhu)
Marvell MVEBU
- Remove duplicate of_clk_get_by_name() call (Andrew Lunn)
- Drop writes to bridge Secondary Status register (Jason Gunthorpe)
- Obey bridge PCI_COMMAND_MEM and PCI_COMMAND_IO bits (Jason Gunthorpe)
- Support a bridge with no IO port window (Jason Gunthorpe)
- Use max_t() instead of max(resource_size_t,) (Jingoo Han)
- Remove redundant of_match_ptr (Sachin Kamat)
- Call pci_ioremap_io() at startup instead of dynamically (Thomas Petazzoni)
NVIDIA Tegra
- Disable Gen2 for Tegra20 and Tegra30 (Eric Brower)
Renesas R-Car
- Add runtime PM support (Valentine Barshak)
- Fix rcar_pci_probe() return value check (Wei Yongjun)
Synopsys DesignWare
- Fix crash in dw_msi_teardown_irq() (Bjørn Erik Nilsen)
- Remove redundant call to pci_write_config_word() (Bjørn Erik Nilsen)
- Fix missing MSI IRQs (Harro Haan)
- Add dw_pcie prefix before cfg_read/write (Pratyush Anand)
- Fix I/O transfers by using CPU (not realio) address (Pratyush Anand)
- Whitespace cleanup (Jingoo Han)
EISA
- Call put_device() if device_register() fails (Levente Kurusa)
- Revert EISA initialization breakage ((Bjorn Helgaas)
Miscellaneous
- Remove unused code, including PCIe 3.0 interfaces (Stephen Hemminger)
- Prevent bus conflicts while checking for bridge apertures (Bjorn Helgaas)
- Stop clearing bridge Secondary Status when setting up I/O aperture (Bjorn Helgaas)
- Use dev_is_pci() to identify PCI devices (Yijing Wang)
- Deprecate DEFINE_PCI_DEVICE_TABLE (Joe Perches)
- Update documentation 00-INDEX (Erik Ekman)"
* tag 'pci-v3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (119 commits)
Revert "EISA: Initialize device before its resources"
Revert "EISA: Log device resources in dmesg"
vfio-pci: Use pci "try" reset interface
PCI: Check parent kobject in pci_destroy_dev()
xen/pcifront: Use global PCI rescan-remove locking
powerpc/eeh: Use global PCI rescan-remove locking
PCI: Fix pci_check_and_unmask_intx() comment typos
PCI: Add pci_try_reset_function(), pci_try_reset_slot(), pci_try_reset_bus()
MPT / PCI: Use pci_stop_and_remove_bus_device_locked()
platform / x86: Use global PCI rescan-remove locking
PCI: hotplug: Use global PCI rescan-remove locking
pcmcia: Use global PCI rescan-remove locking
ACPI / hotplug / PCI: Use global PCI rescan-remove locking
ACPI / PCI: Use global PCI rescan-remove locking in PCI root hotplug
PCI: Add global pci_lock_rescan_remove()
PCI: Cleanup pci.h whitespace
PCI: Reorder so actual code comes before stubs
PCI/AER: Support ACPI HEST AER error sources for PCI domains other than 0
ACPICA: Add helper macros to extract bus/segment numbers from HEST table.
PCI: Make local functions static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Support for some new embedded controllers.
A couple late (<= a week) fixes have stable cc'd and one patch ("SATA:
MV: Add support for the optional PHYs") got committed yesterday
because otherwise the resulting kernel would fail boot on an embedded
board due to interdependent changes in its platform tree.
Other than that, nothing too noteworthy"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
SATA: MV: Add support for the optional PHYs
sata-highbank: Remove unnecessary ahci_platform.h include
libata: disable LPM for some WD SATA-I devices
ARM: mvebu: update the SATA compatible string for Armada 370/XP
ata: sata_mv: fix disk hotplug for Armada 370/XP SoCs
ata: sata_mv: introduce compatible string "marvell, armada-370-sata"
ata: pata_samsung_cf: Remove unused macros
ata: pata_samsung_cf: Use devm_ioremap_resource()
ata: pata_samsung_cf: Merge pata_samsung_cf.h into pata_samsung_cf.c
ata: pata_samsung_cf: Move plat/regs-ata.h to drivers/ata
drivers: ata: Mark the function as static in libahci.c
drivers: ata: Mark the function ahci_init_interrupts() as static in ahci.c
ahci: imx: fix the error handling in imx_ahci_probe()
ahci: imx: ahci_imx_softreset() can be static
ahci: imx: Add i.MX53 support
ahci: imx: Pull out the clock enable/disable calls
libata, dt: Document sata_rcar bindings
sata_rcar: Add R-Car Gen2 SATA PHY support
ahci: mcp89: enter AHCI mode under Apple BIOS emulation
ata: libata-eh: Remove unnecessary snprintf arithmetic
|
|
Some Marvell SoCs have a SATA PHY which can be powered off, in order
to save power. Make use of the generic phy framework to control these
phys.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The sata-highbank driver is a complete standalone sata driver, which does
not use ahci_platform.c / ahci_platform_data in any way.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Cc: stable@vger.kernel.org
|
|
A scheduled horkage patch will conflict with HORKAGE changes in
for-3.13-fixes. Pull in to avoid unnecessary merge conflicts.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the
re-plug events are not detected by the sata_mv driver. This patch fixes
the issue by updating the PHY speed in the LP_PHY_CTL register (0x58)
according to the SControl speed.
Note that this fix is only applied if the compatible string
"marvell,armada-370-sata" is found in the SATA DT node.
Fixes: 9ae6f740b49f ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The sata_mv driver supports the SATA IP found in several Marvell SoCs.
As some new SATA registers have been introduced with the Armada 370/XP
SoCs, a way to identify them is needed.
This patch introduces a new compatible string for the SATA IP found in
Armada 370/XP SoCs.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
* acpi-hotplug:
ACPI / scan: ACPI device object sysfs attribute for _STA evaluation
ACPI / hotplug / driver core: Handle containers in a special way
ACPI / hotplug: Add demand_offline hotplug profile flag
ACPI / bind: Move acpi_get_child() to drivers/ide/ide-acpi.c
ACPI / bind: Pass struct acpi_device pointer to acpi_bind_one()
ACPI / bind: Rework struct acpi_bus_type
ACPI / bind: Redefine acpi_preset_companion()
ACPI / bind: Redefine acpi_get_child()
PCI / ACPI: Use acpi_find_child_device() for child devices lookup
ACPI / bind: Simplify child device lookups
ACPI / scan: Use direct recurrence for device hierarchy walks
ACPI: Introduce acpi_set_device_status()
ACPI / hotplug: Drop unfinished global notification handling routines
ACPI / hotplug: Rework generic code to handle suprise removals
ACPI / hotplug: Move container-specific code out of the core
ACPI / hotplug: Make ACPI PCI root hotplug use common hotplug code
ACPI / hotplug: Introduce common hotplug function acpi_device_hotplug()
ACPI / hotplug: Do not fail bus and device checks for disabled hotplug
ACPI / scan: Add acpi_device objects for all device nodes in the namespace
ACPI / scan: Define non-empty device removal handler
|
|
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
|
|
These macros are not used in the file. Remove them.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Late fixes for libata. Nothing too interesting. Adding missing PM
callbacks to satat_sis and an additional PCI ID for ahci"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_sis: missing PM support
ahci: add PCI ID for Marvell 88SE9170 SATA controller
|
|
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Since pata_samsung_cf.h is referenced only by pata_samsung_cf.c, merge
it into the .c file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
sata_sis has no suspend/resume methods. The default ones will do fine and
are needed on some systems.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch adds support for the PCI ID provided by the Marvell 88SE9170
SATA controller.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
plat/regs-ata.h is used only by Samsung PATA driver.
Move this file to the drivers folder to remove platform
dependency required for multiplatform support.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
|
|
Freezable kthreads and workqueues are fundamentally problematic in
that they effectively introduce a big kernel lock widely used in the
kernel and have already been the culprit of several deadlock
scenarios. This is the latest occurrence.
During resume, libata rescans all the ports and revalidates all
pre-existing devices. If it determines that a device has gone
missing, the device is removed from the system which involves
invalidating block device and flushing bdi while holding driver core
layer locks. Unfortunately, this can race with the rest of device
resume. Because freezable kthreads and workqueues are thawed after
device resume is complete and block device removal depends on
freezable workqueues and kthreads (e.g. bdi_wq, jbd2) to make
progress, this can lead to deadlock - block device removal can't
proceed because kthreads are frozen and kthreads can't be thawed
because device resume is blocked behind block device removal.
839a8e8660b6 ("writeback: replace custom worker pool implementation
with unbound workqueue") made this particular deadlock scenario more
visible but the underlying problem has always been there - the
original forker task and jbd2 are freezable too. In fact, this is
highly likely just one of many possible deadlock scenarios given that
freezer behaves as a big kernel lock and we don't have any debug
mechanism around it.
I believe the right thing to do is getting rid of freezable kthreads
and workqueues. This is something fundamentally broken. For now,
implement a funny workaround in libata - just avoid doing block device
hot[un]plug while the system is frozen. Kernel engineering at its
finest. :(
v2: Add EXPORT_SYMBOL_GPL(pm_freezing) for cases where libata is built
as a module.
v3: Comment updated and polling interval changed to 10ms as suggested
by Rafael.
v4: Add #ifdef CONFIG_FREEZER around the hack as pm_freezing is not
defined when FREEZER is not configured thus breaking build.
Reported by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tomaž Šolc <tomaz.solc@tablix.org>
Reviewed-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=62801
Link: http://lkml.kernel.org/r/20131213174932.GA27070@htj.dyndns.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Cc: kbuild test robot <fengguang.wu@intel.com>
|
|
Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer. This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.
tj: Merged two unnecessarily split patches and made minor edits
including shortening horkage name.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+
|
|
A user on StackExchange had a failing SSD that's soldered directly
onto the motherboard of his system. The BIOS does not give any option
to disable it at all, so he can't just hide it from the OS via the
BIOS.
The old IDE layer had hdX=noprobe override for situations like this,
but that was never ported to the libata layer.
This patch implements a disable flag for libata.force.
Example use:
libata.force=2.0:disable
[v2 of the patch, removed the nodisable flag per Tejun Heo]
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Link: http://unix.stackexchange.com/questions/102648/how-to-tell-linux-kernel-3-0-to-completely-ignore-a-failing-disk
Link: http://askubuntu.com/questions/352836/how-can-i-tell-linux-kernel-to-completely-ignore-a-disk-as-if-it-was-not-even-co
Link: http://superuser.com/questions/599333/how-to-disable-kernel-probing-for-drive
|
|
The check for "combined mode" (which disables ahci support) on ICH6 is
done after the first use of AHCI BAR. But if ahci is not enabled AHCI
BAR is initialized to 0x00000000. (At least it is on the ICH6-M I tested
this on. If I understand the datasheet correctly it should also be on
ICH6R.) This apparently makes the call of
pcim_iomap_regions_request_all() return -EINVAL. And we end up with
ahci: probe of 0000:00:1f.2 failed with error -22
(at warning level) in the logs.
So check for "combined mode" before calling
pcim_iomap_regions_request_all().
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch marks the function ahci_port_intr() and
ahci_hw_port_interrupt() as static in libahci.c because they are not
used outside this file.
Thus, it also eliminates the following warnings in libahci.c:
drivers/ata/libahci.c:1767:6: warning: no previous prototype for ‘ahci_port_intr’ [-Wmissing-prototypes]
drivers/ata/libahci.c:1800:6: warning: no previous prototype for ‘ahci_hw_port_interrupt’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
This patch marks the function ahci_init_interrupts() as static in ahci.c
because it is not used outside this file.
Thus, it also eliminates the following warning in ahci.c:
drivers/ata/ahci.c:1099:5: warning: no previous prototype for ‘ahci_init_interrupts’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
Release alloced resources instead of direct return from
imx_ahci_probe() in the error handling case.
Fixes: 4a23d1793f8e ('ahci: imx: Add i.MX53 support')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Modify acpi_preset_companion() to take a struct acpi_device pointer
instead of an ACPI handle as its second argument and redefine it as
a static inline wrapper around ACPI_COMPANION_SET() passing the
return value of acpi_find_child_device() directly as the second
argument to it. Update its users to pass struct acpi_device
pointers instead of ACPI handles to it.
This allows some unnecessary acpi_bus_get_device() calls to be
avoided.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com> # for ATA binding
|
|
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of nine fixes (and one author update).
The libsas one should fix discovery in eSATA devices, the WRITE_SAME
one is the largest, but it should fix a lot of problems we've been
getting with the emulated RAID devices (they've been effectively lying
about support and then firmware has been choking on the commands).
The rest are various crash, hang or warn driver fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bfa: Fix crash when symb name set for offline vport
[SCSI] enclosure: fix WARN_ON in dual path device removing
[SCSI] pm80xx: Tasklets synchronization fix.
[SCSI] pm80xx: Resetting the phy state.
[SCSI] pm80xx: Fix for direct attached device.
[SCSI] pm80xx: Module author addition
[SCSI] hpsa: return 0 from driver probe function on success, not 1
[SCSI] hpsa: do not discard scsi status on aborted commands
[SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
[SCSI] libsas: fix usage of ata_tf_to_fis
|
|
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add minor adjustments to support i.MX53 SATA port as well as i.MX6Q one.
The difference here is mostly the clock which need to be enabled and also
the lack of need of programming IOMUXC registers on i.MX53. All of which
is well handles in the clock enable/disable functions. Note that this patch
also cleans up the names of the common functions, so they don't read imx6q_*
but imx_* instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The same code for enabling and disabling SATA clock was found in multiple
places in the driver. Implement functions that enable/disable the SATA clock
and use them in such places instead of duplicating the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pulling in for-3.13-fixes for the ahci_imx fix as further changes
depend on it.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
We must clear this IMX6Q_GPR13_SATA_MPLL_CLK_EN bit on i.MX6Q, otherwise
Linux will fail to find the attached drive on some boards.
This entire fix was:
Reported-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
