| Age | Commit message (Collapse) | Author |
|---|
|
* acpi-rtc:
ACPI / RTC: Fix CMOS RTC opregion handler accesses to wrong addresses
* acpi-lpss:
ACPI / LPSS: complete PM entries for LPSS power domain
* acpi-battery:
Revert "ACPI / battery: fix wrong value of capacity_now reported when fully charged"
Revert "ACPI / battery: Fix warning message in acpi_battery_get_state()"
|
|
PM entries of LPSS power domain were not implemented correctly
in commit c78b0830667a "ACPI / LPSS: custom power domain for LPSS".
This patch fixes and completes these PM entries.
Fixes: c78b0830667a (ACPI / LPSS: custom power domain for LPSS)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
charged"
This reverts commit 232de5143790 ("ACPI / battery: fix wrong value of
capacity_now reported when fully charged")
There is nothing wrong or unexpected about 'capacity_now' increasing above
the last 'full_charge_capacity' value. Different charging cycles will cause
'full_charge_capacity' to vary, both up and down. Good battery firmwares
will update 'full_charge_capacity' when the current charging cycle is
complete, increasing it if necessary. It might even go above
'design_capacity' on a fresh and healthy battery.
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong, and
printing a warning if this doesn't happen to match the 'design_capacity'
is both annoying and terribly wrong.
This results in bogus warnings on perfectly working systems/firmwares:
[Firmware Bug]: battery: reported current charge level (39800) is higher than reported maximum charge level (39800).
and wrong values being reported for 'capacity_now' and
'full_charge_capacity' after the warning has been triggered.
Fixes: 232de5143790 ("ACPI / battery: fix wrong value of capacity_now reported when fully charged")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts commit d719870b41e0 ("ACPI / battery: Fix warning message in
acpi_battery_get_state()")
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong. If this
is necessary to work around some buggy firmware, then the workaround needs
protection against being applied to working firmwares.
Good battery firmwares will allow 'capacity_now' to increase above
'full_charge_capacity', and will update the latter when the battery
is fully charged. By capping 'capacity_now' we lose accurate capacity
reporting until charging is complete whenever 'full_charge_capacity'
needs to be increased.
Fixes: d719870b41e0 ("ACPI / battery: Fix warning message in acpi_battery_get_state()")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The value64 parameter is an u64 point that used to transfer the value
for write to CMOS, or used to return the value that's read from CMOS.
The value64 is an u64 point, so don't need get address again. It causes
acpi_cmos_rtc_space_handler always return 0 to reader and didn't write
expected value to CMOS.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* acpi-video:
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
* acpi-ec:
ACPI / EC: Add msi quirk for Clevo W350etq
|
|
* acpica:
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
* acpi-processor:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
* acpi-scan:
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
|
|
There is a following AB-BA dependency between cpu_hotplug.lock and
cpuidle_lock:
1) cpu_hotplug.lock -> cpuidle_lock
enable_nonboot_cpus()
_cpu_up()
cpu_hotplug_begin()
LOCK(cpu_hotplug.lock)
cpu_notify()
...
acpi_processor_hotplug()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
2) cpuidle_lock -> cpu_hotplug.lock
acpi_os_execute_deferred() workqueue
...
acpi_processor_cst_has_changed()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
get_online_cpus()
LOCK(cpu_hotplug.lock)
Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The _SUN device indentification object is not guaranteed to return
the same value every time it is executed, so we should not cache its
return value, but rather execute it every time as needed. If it is
cached, an incorrect stale value may be used in some situations.
This issue was exposed by commit 202317a573b2 (ACPI / scan: Add
acpi_device objects for all device nodes in the namespace). Fix it
by avoiding to cache the return value of _SUN.
Fixes: 202317a573b2 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Clevo W350etq's EC will not produce GPE interrupt some time after
booting. The ACPI notify event won't trigger when the issue takes
place. After debugging, adding msi quirk for the machine can fix
the issue. This patch is to add msi quirk for the machine.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Reported-and-tested-by: qbanin@gmail.com
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Link: https://bugs.freedesktop.org/show_bug.cgi?id=81515
Reported-and-tested-by: Hohahiu <rakothedin@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some laptops have a working acpi_video backlight control, and using native
backlight on these causes a regression where backlight control does not work
when userspace is not handling brightness key events. Disable native_backlight
on these to fix this.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81691
Reported-and-tested-by: Andre Müller <andre.muller@web.de>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 751109aad583 ("ACPI / video: Change the default for
video.use_native_backlight to 1") has changed the default for
use_native_backlight from 0 to 1, but instead of changing
use_native_backlight_dmi to true, and leaving use_native_backlight_param at -1,
it has changed use_native_backlight_param to 1.
This causes acpi_video_use_native_backlight() to always think that a value was
specified through the param, making it impossible to add a dmi based quirk
to force 0 now that the default is 1.
This fixes this by restoring the use_native_backlight_param default to -1, and
instead setting the use_native_backlight_dmi default to true.
Fixes: 751109aad583 (ACPI / video: Change the default for video.use_native_backlight to 1)
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adds ACPICA kernel runtime support to validate contents/format
of the _DSD package, similar to the iASL support. Ported by
Mika Westerberg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"One patch to avoid assigning interrupts we don't actually have on
non-PC platforms, and two patches that addresses bugs in the new
IOAPIC assignment code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, irq, PCI: Keep IRQ assignment for runtime power management
x86: irq: Fix bug in setting IOAPIC pin attributes
x86: Fix non-PC platform kernel crash on boot due to NULL dereference
|
|
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235c17a7 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
* acpi-scan:
ACPI: Run fixed event device notifications in process context
ACPI / scan: Allow ACPI drivers to bind to PNP device objects
* acpi-ec:
ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
* acpi-lpss:
ACPI / LPSS: Add ACPI IDs for Intel Braswell
|
|
Enable more identifiers for the existing devices for Intel Braswell and
Cherryview.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
previous QR_EC
There is platform refusing to respond QR_EC when SCI_EVT isn't set
which is Acer Aspire V5-573G.
By disallowing QR_EC to be issued before the previous one has been
completed we are able to reduce the possibilities to trigger issues on
such platforms.
Note that this fix can only reduce the occurrence rate of this issue, but
this issue may still occur when such a platform doesn't clear SCI_EVT
before or immediately after completing the previous QR_EC transaction.
This patch cannot fix the CLEAR_ON_RESUME quirk which also relies on
the assumption that the platforms are able to respond even when SCI_EVT
isn't set.
But this patch is still useful as it can help to reduce the number of
scheduled QR_EC work items.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Reported-and-tested-by: Alexander Mezin <mezin.alexander@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is a platform refusing to respond QR_EC when SCI_EVT isn't set
(Acer Aspire V5-573G).
Currently, we rely on the behaviour that the EC firmware can respond
something (for example, 0x00 to indicate "no outstanding events") to
QR_EC even when SCI_EVT is not set, but the reporter has complained
about AC/battery pluging/unpluging and video brightness change delay
on that platform.
This is because the work item that has issued QR_EC has to wait until
timeout in this case, and the _Qxx method evaluation work item queued
after QR_EC one is delayed.
It sounds reasonable to fix this issue by:
1. Implementing SCI_EVT sanity check before issuing QR_EC in the EC
driver's main state machine.
2. Moving QR_EC issuing out of the work queue used by _Qxx evaluation
to a seperate IRQ handling thread.
This patch fixes this issue using solution 1.
By disallowing QR_EC to be issued when SCI_EVT isn't set, we are able to
handle such platform in the EC driver's main state machine. This patch
enhances the state machine in this way to survive with such malfunctioning
EC firmware.
Note that this patch can also fix CLEAR_ON_RESUME quirk which also relies
on the assumption that the platforms are able to respond even when SCI_EVT
isn't set.
Fixes: c0d653412fc8 ACPI / EC: Fix race condition in ec_transaction_completed()
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Reported-and-tested-by: Alexander Mezin <mezin.alexander@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, notify callbacks for fixed button events are run from
interrupt context. That is not necessary and after commit 0bf6368ee8f2
(ACPI / button: Add ACPI Button event via netlink routine) it causes
netlink routines to be called from interrupt context which is not
correct.
Also, that is different from non-fixed device events (including
non-fixed button events) whose notify callbacks are all executed from
process context.
For the above reasons, make fixed button device notify callbacks run
in process context which will avoid the deadlock when using netlink
to report button events to user space.
Fixes: 0bf6368ee8f2 (ACPI / button: Add ACPI Button event via netlink routine)
Link: https://lkml.org/lkml/2014/8/21/606
Reported-by: Benjamin Block <bebl@mageta.org>
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
[rjw: Function names, subject and changelog.]
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We generally don't allow ACPI drivers to bind to ACPI device objects
that companion "physical" device objects are created for to avoid
situations in which two different drivers may attempt to handle one
device at the same time. Recent ACPI device enumeration rework
extended that approach to ACPI PNP devices by starting to use a scan
handler for enumerating them. However, we previously allowed ACPI
drivers to bind to ACPI device objects with existing PNP device
companions and changing that led to functional regressions on some
systems.
For this reason, add a special check for PNP devices in
acpi_device_probe() so that ACPI drivers can bind to ACPI device
objects having existing PNP device companions as before.
Fixes: eec15edbb0e1 (ACPI / PNP: use device ID list for PNPACPI device enumeration)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81511
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81971
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: Dirk Griesbach <spamthis@freenet.de>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are a couple of regression fixes, cpuidle menu governor
optimizations, fixes for ACPI proccessor and battery drivers,
hibernation fix to avoid problems related to the e820 memory map,
fixes for a few cpufreq drivers and a new version of the suspend
profiling tool analyze_suspend.py.
Specifics:
- Fix for an ACPI-based device hotplug regression introduced in 3.14
that causes a kernel panic to trigger when memory hot-remove is
attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen
- Fix for a cpufreq regression introduced in 3.16 that triggers a
"sleeping function called from invalid context" bug in
dev_pm_opp_init_cpufreq_table() from Stephen Boyd
- ACPI battery driver fix for a warning message added in 3.16 that
prints silly stuff sometimes from Mariusz Ceier
- Hibernation fix for safer handling of mismatches in the 820 memory
map between the configurations during image creation and during the
subsequent restore from Chun-Yi Lee
- ACPI processor driver fix to handle CPU hotplug notifications
correctly during system suspend/resume from Lan Tianyu
- Series of four cpuidle menu governor cleanups that also should
speed it up a bit from Mel Gorman
- Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus
Pargmann and Uwe Kleine-König
- Version 3.0 of the analyze_suspend.py suspend profiling tool from
Todd E Brandt"
* tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / battery: Fix warning message in acpi_battery_get_state()
PM / tools: analyze_suspend.py: update to v3.0
cpufreq: arm_big_little: fix module license spec
cpufreq: speedstep-smi: fix decimal printf specifiers
ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
cpufreq: OPP: Avoid sleeping while atomic
cpufreq: cpu0: Do not print error message when deferring
cpufreq: integrator: Use set_cpus_allowed_ptr
PM / hibernate: avoid unsafe pages in e820 reserved regions
ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
cpuidle: menu: Lookup CPU runqueues less
cpuidle: menu: Call nr_iowait_cpu less times
cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
cpuidle: menu: Use shifts when calculating averages where possible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/apic updates from Thomas Gleixner:
"This is a major overhaul to the x86 apic subsystem consisting of the
following parts:
- Remove obsolete APIC driver abstractions (David Rientjes)
- Use the irqdomain facilities to dynamically allocate IRQs for
IOAPICs. This is a prerequisite to enable IOAPIC hotplug support,
and it also frees up wasted vectors (Jiang Liu)
- Misc fixlets.
Despite the hickup in Ingos previous pull request - caused by the
missing fixup for the suspend/resume issue reported by Borislav - I
strongly recommend that this update finds its way into 3.17. Some
history for you:
This is preparatory work for physical IOAPIC hotplug. The first
attempt to support this was done by Yinghai and I shot it down because
it just added another layer of obscurity and complexity to the already
existing mess without tackling the underlying shortcomings of the
current implementation.
After quite some on- and offlist discussions, I requested that the
design of this functionality must use generic infrastructure, i.e.
irq domains, which provide all the mechanisms to dynamically map linux
interrupt numbers to physical interrupts.
Jiang picked up the idea and did a great job of consolidating the
existing interfaces to manage the x86 (IOAPIC) interrupt system by
utilizing irq domains.
The testing in tip, Linux-next and inside of Intel on various machines
did not unearth any oddities until Borislav exposed it to one of his
oddball machines. The issue was resolved quickly, but unfortunately
the fix fell through the cracks and did not hit the tip tree before
Ingo sent the pull request. Not entirely Ingos fault, I also assumed
that the fix was already merged when Ingo asked me whether he could
send it.
Nevertheless this work has a proper design, has undergone several
rounds of review and the final fallout after applying it to tip and
integrating it into Linux-next has been more than moderate. It's the
ground work not only for IOAPIC hotplug, it will also allow us to move
the lowlevel vector allocation into the irqdomain hierarchy, which
will benefit other architectures as well. Patches are posted already,
but they are on hold for two weeks, see below.
I really appreciate the competence and responsiveness Jiang has shown
in course of this endavour. So I'm sure that any fallout of this will
be addressed in a timely manner.
FYI, I'm vanishing for 2 weeks into my annual kids summer camp kitchen
duty^Wvacation, while you folks are drooling at KS/LinuxCon :) But HPA
will have a look at the hopefully zero fallout until I'm back"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
x86, irq, PCI: Keep IRQ assignment for PCI devices during suspend/hibernation
x86/apic/vsmp: Make is_vsmp_box() static
x86, apic: Remove enable_apic_mode callback
x86, apic: Remove setup_portio_remap callback
x86, apic: Remove multi_timer_check callback
x86, apic: Replace noop_check_apicid_used
x86, apic: Remove check_apicid_present callback
x86, apic: Remove mps_oem_check callback
x86, apic: Remove smp_callin_clear_local_apic callback
x86, apic: Replace trampoline physical addresses with defaults
x86, apic: Remove x86_32_numa_cpu_node callback
x86: intel-mid: Use the new io_apic interfaces
x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
x86, irq: Clean up irqdomain transition code
x86, irq, devicetree: Release IOAPIC pin when PCI device is disabled
x86, irq, SFI: Release IOAPIC pin when PCI device is disabled
x86, irq, mpparse: Release IOAPIC pin when PCI device is disabled
x86, irq, ACPI: Release IOAPIC pin when PCI device is disabled
x86, irq: Introduce helper functions to release IOAPIC pin
x86, irq: Simplify the way to handle ISA IRQ
...
|
|
* acpi-processor:
ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
* acpi-hotplug:
ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
* acpi-battery:
ACPI / battery: Fix warning message in acpi_battery_get_state()
|
|
capacity_now should be assigned after comparing it to design_capacity.
Otherwise warning is printed even when capacity_now before assignment is
equal to design_capacity, making the check useless and "current charge level"
wrong (it should be higher than, not equal to, "maximum charge level", which
is full_charge_capacity):
"battery: reported current charge level (56410) is higher than reported
maximum charge level (56410)."
Fixes: 232de5143790 (ACPI / battery: fix wrong value of capacity_now reported when fully charged)
Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during suspend/hibernation,
otherwise it may cause failure of suspend/hibernation due to:
1) Device driver calls pci_enable_device() to allocate an IRQ number
and register interrupt handler on the returned IRQ.
2) Device driver's suspend callback calls pci_disable_device() and
release assigned IRQ in turn.
3) Device driver's resume callback calls pci_enable_device() to
allocate IRQ number again. A different IRQ number may be assigned
by IOAPIC driver this time.
4) Now the hardware delivers interrupt to the new IRQ but interrupt
handler is still registered against the old IRQ, so it breaks
suspend/hibernation.
To fix this issue, we keep IRQ assignment during suspend/hibernation.
Flag pci_dev.dev.power.is_prepared is used to detect that
pci_disable_device() is called during suspend/hibernation.
Reported-and-Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1407478071-29399-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When ACPI_HOTPLUG_MEMORY is not configured, memory_device_handler.attach
is not set. In acpi_scan_attach_handler(), the acpi_device->handler will
not be initialized.
In acpi_scan_hot_remove(), it doesn't check if acpi_device->handler is NULL.
If we do memory hot-remove without ACPI_HOTPLUG_MEMORY configured, the kernel
will panic.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff813e318f>] acpi_device_hotplug+0x1d7/0x4c4
PGD 0
Oops: 0000 [#1] SMP
Modules linked in: sd_mod(E) sr_mod(E) cdrom(E) crc_t10dif(E) crct10dif_common(E) ata_piix(E) libata(E)
CPU: 0 PID: 41 Comm: kworker/u2:1 Tainted: G E 3.16.0-rc7--3.16-rc7-tangchen+ #20
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
task: ffff8800182436c0 ti: ffff880018254000 task.ti: ffff880018254000
RIP: 0010:[<ffffffff813e318f>] [<ffffffff813e318f>] acpi_device_hotplug+0x1d7/0x4c4
RSP: 0000:ffff880018257da8 EFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff88001cd8d800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88001e40e6f8 RDI: 0000000000000246
RBP: ffff880018257df0 R08: 0000000000000096 R09: 00000000000011a0
R10: 63735f6970636120 R11: 725f746f685f6e61 R12: 0000000000000003
R13: ffff88001cc1c400 R14: ffff88001e062028 R15: 0000000000000040
FS: 0000000000000000(0000) GS:ffff88001e400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000088 CR3: 000000001a9a2000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
Stack:
00000000523cab58 ffff88001cd8d9f8 ffff88001852d480 00000000523cab58
ffff88001852d480 ffff880018221e40 ffff88001cc1c400 ffff88001cce2d00
0000000000000040 ffff880018257e08 ffffffff813dc31d ffff88001852d480
Call Trace:
[<ffffffff813dc31d>] acpi_hotplug_work_fn+0x1e/0x29
[<ffffffff8108eefb>] process_one_work+0x17b/0x460
[<ffffffff8108f69d>] worker_thread+0x11d/0x5b0
[<ffffffff8108f580>] ? rescuer_thread+0x3a0/0x3a0
[<ffffffff81096811>] kthread+0xe1/0x100
[<ffffffff81096730>] ? kthread_create_on_node+0x1a0/0x1a0
[<ffffffff816cc6bc>] ret_from_fork+0x7c/0xb0
[<ffffffff81096730>] ? kthread_create_on_node+0x1a0/0x1a0
This patch fixes this problem by checking if acpi_device->handler is NULL
in acpi_scan_hot_remove().
Fixes: d22ddcbc4fb7 (ACPI / hotplug: Add demand_offline hotplug profile flag)
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Again, ACPICA leads the pack (47 commits), followed by cpufreq (18
commits) and system suspend/hibernation (9 commits).
From the new code perspective, the ACPICA update brings ACPI 5.1 to
the table, including a new device configuration object called _DSD
(Device Specific Data) that will hopefully help us to operate device
properties like Device Trees do (at least to some extent) and changes
related to supporting ACPI on ARM.
Apart from that we have hibernation changes making it use radix trees
to store memory bitmaps which should speed up some operations carried
out by it quite significantly. We also have some power management
changes related to suspend-to-idle (the "freeze" sleep state) support
and more preliminary changes needed to support ACPI on ARM (outside of
ACPICA).
The rest is fixes and cleanups pretty much everywhere.
Specifics:
- ACPICA update to upstream version 20140724. That includes ACPI 5.1
material (support for the _CCA and _DSD predefined names, changes
related to the DMAR and PCCT tables and ARM support among other
things) and cleanups related to using ACPICA's header files. A
major part of it is related to acpidump and the core code used by
that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and Rafael J
Wysocki.
- Cleanups and improvements related to system suspend from Lan
Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand governor
and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from Mikulas
Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano, Sandeep
Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas
Renninger"
* tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (118 commits)
ACPI / LPSS: add LPSS device for Wildcat Point PCH
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
ACPI / processor: Make it possible to get local x2apic id via _MAT
...
|
|
CPU hotplug happens during S2RAM and CPU notify event will be CPU_XXX_FROZEN.
acpi_cpu_soft_notify() ignores to check these events. This also may make
acpi_cpu_soft_notify() fall into sleep during CPU_DYING/STARTING_FROZEN
events which don't allow callbacks to sleep. This patch is to fix it.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* acpi-video:
ACPI / video: Add use_native_backlight quirk for HP EliteBook 2014 models
* acpi-battery:
ACPI / battery: remove duplicated include from battery.c
* acpi-processor:
ACPI / processor: Make it possible to get local x2apic id via _MAT
* acpi-lpss:
ACPI / LPSS: add LPSS device for Wildcat Point PCH
|
|
* acpi-pnp:
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPI / PNP: Fix acpi_pnp_match()
|
|
* acpica:
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
|
|
INT3438 is the ADSP device on Wildcat Point platform
with 2 DW DMA engines built In. The DMA engines are
used for DSP FW loading and audio data transferring.
These DMA engine probing need the clock, without it,
probing may failed and can't go forward.
Add LPSS device "INT3438" for Wildcat Point PCH, to
provide clock for its ADSP DMA engine probing.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
0 is ascii for NULL. Hex digit matching should be from '0'.
Faulty version returns true for #,$,%,& etc.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Full support for _CCA.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
New value for the Notify() operator.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adds full support for _DSD. David Box.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Simplifies timing of things like control method execution.
[zetalog: fixing 64-bit division link error]
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This adds a -u option to acpi_help to display all known ACPI UUIDs.
Some existing files in the core code have been restructured.
Three new files.
[zetalog: changing drivers/acpi/acpica/Makefile accordingly]
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The bug can be reproduced by using a format that do not have the width.prec
specified after a format that have the width.prec specified. The second
formatted output will be wrong. The root cause is acpi_ut_vsnprintf()
doesn't reset the specifiers to the default values.
This patch fixes this issue. BZ 1094. Reported by Yizhe Wang, fixed by
Lv Zheng.
Since acpi_ut_vprintf() is only enabled for specific OSPM now, this patch
doesn't affect Linux kernel.
Link: https://bugs.acpica.org/show_bug.cgi?id=1094
Reported-and-tested-by: Yizhe Wang <yizhe.wang@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Arguments that have no associated % format specifier.
Apparently these are not caught by any current compilers.
ACPICA BZ 1090. Sascha Wildner.
Currently, this patch only affects applications under the
toos/power/acpi folder.
Link: https://bugs.acpica.org/show_bug.cgi?id=1090
Signed-off-by: Sascha Wildner <swildner@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix some issues detected by acpisrc utility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This change adds support to disassemble a UUID back to the original
ToUUID operator. It will detect a UUID within a standard AML Buffer.
Also, a description of the UUID is emitted for "known" UUIDs, defined
as UUIDs that are defined in the ACPI specification.
Since this is a change for disassembler which is not shipped in the
Linux kernel, the Linux kernel is not affected.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
warning: cast from function call of type 'char *' to non-matching type 'long unsigned int'
Since acpi_ut_format_number() hasn't been enabled for the Linux kernel,
this patch doesn't affect the Linux kernel.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
APEI is currently implemented so that it depends on x86 hardware.
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
|
|
Logical processors with APIC ID values of 255 and greater are
required to have a Processor Device object and must convey the
processor's APIC information to OSPM using the Processor Local
X2APIC structure, but not until ACPI 5.1, X2APIC structure was
not supported in _MAT method.
_MAT is needed for CPU hotplug and system with more than 255
CPUs will definitely need X2APIC structure, so add its support
in map_mat_entry() to make it possible to get local x2apic id
via _MAT based on ACPI 5.1.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1123565
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Conflicts:
drivers/pnp/pnpacpi/core.c
|
