| Age | Commit message (Collapse) | Author |
|---|
|
In the quest to remove all stack VLA usage from the kernel[1], this
exposes a new general upper bound on crypto blocksize and alignmask
(higher than for the existing cipher limits) for VLA removal,
and introduces new checks.
At present, the highest cra_alignmask in the kernel is 63. The highest
cra_blocksize is 144 (SHA3_224_BLOCK_SIZE, 18 8-byte words). For the
new blocksize limit, I went with 160 (20 8-byte words).
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In the quest to remove all stack VLA usage from the kernel[1], this
removes the VLAs in SHASH_DESC_ON_STACK (via crypto_shash_descsize())
by using the maximum allowable size (which is now more clearly captured
in a macro), along with a few other cases. Similar limits are turned into
macros as well.
A review of existing sizes shows that SHA512_DIGEST_SIZE (64) is the
largest digest size and that sizeof(struct sha3_state) (360) is the
largest descriptor size. The corresponding maximums are reduced.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In the quest to remove all stack VLA usage from the kernel[1], this drops
AHASH_REQUEST_ON_STACK by preallocating the ahash request area combined
with the skcipher area (which are not used at the same time).
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In the quest to remove all stack VLA usage from the kernel[1], this uses
the maximum blocksize and adds a sanity check. For xcbc, the blocksize
must always be 16, so use that, since it's already being enforced during
instantiation.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
These are unused, undesired, and have never actually been used by
anybody. The original authors of this code have changed their mind about
its inclusion. While originally proposed for disk encryption on low-end
devices, the idea was discarded [1] in favor of something else before
that could really get going. Therefore, this patch removes Speck.
[1] https://marc.info/?l=linux-crypto-vger&m=153359499015659
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull DMAengine updates from Vinod Koul:
"This round brings couple of framework changes, a new driver and usual
driver updates:
- new managed helper for dmaengine framework registration
- split dmaengine pause capability to pause and resume and allow
drivers to report that individually
- update dma_request_chan_by_mask() to handle deferred probing
- move imx-sdma to use virt-dma
- new driver for Actions Semi Owl family S900 controller
- minor updates to intel, renesas, mv_xor, pl330 etc"
* tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Add Actions Semi Owl family S900 DMA driver
dt-bindings: dmaengine: Add binding for Actions Semi Owl SoCs
dmaengine: sh: rcar-dmac: Should not stop the DMAC by rcar_dmac_sync_tcr()
dmaengine: mic_x100_dma: use the new helper to simplify the code
dmaengine: add a new helper dmaenginem_async_device_register
dmaengine: imx-sdma: add memcpy interface
dmaengine: imx-sdma: add SDMA_BD_MAX_CNT to replace '0xffff'
dmaengine: dma_request_chan_by_mask() to handle deferred probing
dmaengine: pl330: fix irq race with terminate_all
dmaengine: Revert "dmaengine: mv_xor_v2: enable COMPILE_TEST"
dmaengine: mv_xor_v2: use {lower,upper}_32_bits to configure HW descriptor address
dmaengine: mv_xor_v2: enable COMPILE_TEST
dmaengine: mv_xor_v2: move unmap to before callback
dmaengine: mv_xor_v2: convert callback to helper function
dmaengine: mv_xor_v2: kill the tasklets upon exit
dmaengine: mv_xor_v2: explicitly freeup irq
dmaengine: sh: rcar-dmac: Add dma_pause operation
dmaengine: sh: rcar-dmac: add a new function to clear CHCR.DE with barrier
dmaengine: idma64: Support dmaengine_terminate_sync()
dmaengine: hsu: Support dmaengine_terminate_sync()
...
|
|
Replace the use of a magic number that indicates that verify_*_signature()
should use the secondary keyring with a symbol.
Signed-off-by: Yannik Sembritzki <yannik@sembritzki.me>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: keyrings@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull integrity updates from James Morris:
"This adds support for EVM signatures based on larger digests, contains
a new audit record AUDIT_INTEGRITY_POLICY_RULE to differentiate the
IMA policy rules from the IMA-audit messages, addresses two deadlocks
due to either loading or searching for crypto algorithms, and cleans
up the audit messages"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
EVM: fix return value check in evm_write_xattrs()
integrity: prevent deadlock during digsig verification.
evm: Allow non-SHA1 digital signatures
evm: Don't deadlock if a crypto algorithm is unavailable
integrity: silence warning when CONFIG_SECURITYFS is not enabled
ima: Differentiate auditing policy rules from "audit" actions
ima: Do not audit if CONFIG_INTEGRITY_AUDIT is not set
ima: Use audit_log_format() rather than audit_log_string()
ima: Call audit_log_string() rather than logging it untrusted
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Fix dcache flushing crash in skcipher.
- Add hash finup self-tests.
- Reschedule during speed tests.
Algorithms:
- Remove insecure vmac and replace it with vmac64.
- Add public key verification for DH/ECDH.
Drivers:
- Decrease priority of sha-mb on x86.
- Improve NEON latency/throughput on ARM64.
- Add md5/sha384/sha512/des/3des to inside-secure.
- Support eip197d in inside-secure.
- Only register algorithms supported by the host in virtio.
- Add cts and remove incompatible cts1 from ccree.
- Add hisilicon SEC security accelerator driver.
- Replace msm hwrng driver with qcom pseudo rng driver.
Misc:
- Centralize CRC polynomials"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (121 commits)
crypto: arm64/ghash-ce - implement 4-way aggregation
crypto: arm64/ghash-ce - replace NEON yield check with block limit
crypto: hisilicon - sec_send_request() can be static
lib/mpi: remove redundant variable esign
crypto: arm64/aes-ce-gcm - don't reload key schedule if avoidable
crypto: arm64/aes-ce-gcm - implement 2-way aggregation
crypto: arm64/aes-ce-gcm - operate on two input blocks at a time
crypto: dh - make crypto_dh_encode_key() make robust
crypto: dh - fix calculating encoded key size
crypto: ccp - Check for NULL PSP pointer at module unload
crypto: arm/chacha20 - always use vrev for 16-bit rotates
crypto: ccree - allow bigger than sector XTS op
crypto: ccree - zero all of request ctx before use
crypto: ccree - remove cipher ivgen left overs
crypto: ccree - drop useless type flag during reg
crypto: ablkcipher - fix crash flushing dcache in error path
crypto: blkcipher - fix crash flushing dcache in error path
crypto: skcipher - fix crash flushing dcache in error path
crypto: skcipher - remove unnecessary setting of walk->nbytes
crypto: scatterwalk - remove scatterwalk_samebuf()
...
|
|
Make it return -EINVAL if crypto_dh_key_len() is incorrect rather than
overflowing the buffer.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
It was forgotten to increase DH_KPP_SECRET_MIN_SIZE to include 'q_size',
causing an out-of-bounds write of 4 bytes in crypto_dh_encode_key(), and
an out-of-bounds read of 4 bytes in crypto_dh_decode_key(). Fix it, and
fix the lengths of the test vectors to match this.
Reported-by: syzbot+6d38d558c25b53b8f4ed@syzkaller.appspotmail.com
Fixes: e3fe0ae12962 ("crypto: dh - add public key verification test")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Like the skcipher_walk and blkcipher_walk cases:
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
ablkcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing ablkcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
Reported-by: Liu Chao <liuchao741@huawei.com>
Fixes: bf06099db18a ("crypto: skcipher - Add ablkcipher_walk interfaces")
Cc: <stable@vger.kernel.org> # v2.6.35+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Like the skcipher_walk case:
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
blkcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing blkcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
This bug was found by syzkaller fuzzing.
Reproducer, assuming ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
struct sockaddr_alg addr = {
.salg_type = "skcipher",
.salg_name = "ecb(aes-generic)",
};
char buffer[4096] __attribute__((aligned(4096))) = { 0 };
int fd;
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buffer, 16);
fd = accept(fd, NULL, NULL);
write(fd, buffer, 15);
read(fd, buffer, 15);
}
Reported-by: Liu Chao <liuchao741@huawei.com>
Fixes: 5cde0af2a982 ("[CRYPTO] cipher: Added block cipher type")
Cc: <stable@vger.kernel.org> # v2.6.19+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
skcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing skcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
This bug was found by syzkaller fuzzing.
Reproducer, assuming ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
struct sockaddr_alg addr = {
.salg_type = "skcipher",
.salg_name = "cbc(aes-generic)",
};
char buffer[4096] __attribute__((aligned(4096))) = { 0 };
int fd;
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buffer, 16);
fd = accept(fd, NULL, NULL);
write(fd, buffer, 15);
read(fd, buffer, 15);
}
Reported-by: Liu Chao <liuchao741@huawei.com>
Fixes: b286d8b1a690 ("crypto: skcipher - Add skcipher walk interface")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Setting 'walk->nbytes = walk->total' in skcipher_walk_first() doesn't
make sense because actually walk->nbytes needs to be set to the length
of the first step in the walk, which may be less than walk->total. This
is done by skcipher_walk_next() which is called immediately afterwards.
Also walk->nbytes was already set to 0 in skcipher_walk_skcipher(),
which is a better default value in case it's forgotten to be set later.
Therefore, remove the unnecessary assignment to walk->nbytes.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
All callers pass chain=0 to scatterwalk_crypto_chain().
Remove this unneeded parameter.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The ALIGN() macro needs to be passed the alignment, not the alignmask
(which is the alignment minus 1).
Fixes: b286d8b1a690 ("crypto: skcipher - Add skcipher walk interface")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Avoid RCU stalls in the case of non-preemptible kernel and lengthy
speed tests by rescheduling when advancing from one block size
to another.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The cipher implementations of the kernel crypto API favor in-place
cipher operations. Thus, switch the CTR cipher operation in the DRBG to
perform in-place operations. This is implemented by using the output
buffer as input buffer and zeroizing it before the cipher operation to
implement a CTR encryption of a NULL buffer.
The speed improvement is quite visibile with the following comparison
using the LRNG implementation.
Without the patch set:
16 bytes| 12.267661 MB/s| 61338304 bytes | 5000000213 ns
32 bytes| 23.603770 MB/s| 118018848 bytes | 5000000073 ns
64 bytes| 46.732262 MB/s| 233661312 bytes | 5000000241 ns
128 bytes| 90.038042 MB/s| 450190208 bytes | 5000000244 ns
256 bytes| 160.399616 MB/s| 801998080 bytes | 5000000393 ns
512 bytes| 259.878400 MB/s| 1299392000 bytes | 5000001675 ns
1024 bytes| 386.050662 MB/s| 1930253312 bytes | 5000001661 ns
2048 bytes| 493.641728 MB/s| 2468208640 bytes | 5000001598 ns
4096 bytes| 581.835981 MB/s| 2909179904 bytes | 5000003426 ns
With the patch set:
16 bytes | 17.051142 MB/s | 85255712 bytes | 5000000854 ns
32 bytes | 32.695898 MB/s | 163479488 bytes | 5000000544 ns
64 bytes | 64.490739 MB/s | 322453696 bytes | 5000000954 ns
128 bytes | 123.285043 MB/s | 616425216 bytes | 5000000201 ns
256 bytes | 233.434573 MB/s | 1167172864 bytes | 5000000573 ns
512 bytes | 384.405197 MB/s | 1922025984 bytes | 5000000671 ns
1024 bytes | 566.313370 MB/s | 2831566848 bytes | 5000001080 ns
2048 bytes | 744.518042 MB/s | 3722590208 bytes | 5000000926 ns
4096 bytes | 867.501670 MB/s | 4337508352 bytes | 5000002181 ns
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Merge mainline to pick up c7513c2a2714 ("crypto/arm64: aes-ce-gcm -
add missing kernel_neon_begin/end pair").
|
|
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the swap macro and remove unnecessary variable *tmp*.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make use of the swap macro and remove unnecessary variable *tmp*.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix the b value to be compliant with FIPS 186-4 D.1.2.1. This fix is
required to make sure the SP800-56A public key test passes for P-192.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
By adding a zero byte-length for the DH parameter Q value, the public
key verification test is disabled for the given test.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The CTR DRBG requires two SGLs pointing to input/output buffers for the
CTR AES operation. The used SGLs always have only one entry. Thus, the
SGL can be initialized during allocation time, preventing a
re-initialization of the SGLs during each call.
The performance is increased by about 1 to 3 percent depending on the
size of the requested buffer size.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In case memory resources for *base* were allocated, release them
before return.
Addresses-Coverity-ID: 1471702 ("Resource leak")
Fixes: e3fe0ae12962 ("crypto: dh - add public key verification test")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes an allocation error-path bug in af_alg discovered by
syzkaller"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: af_alg - Initialize sg_num_bytes in error code path
|
|
When EVM attempts to appraise a file signed with a crypto algorithm the
kernel doesn't have support for, it will cause the kernel to trigger a
module load. If the EVM policy includes appraisal of kernel modules this
will in turn call back into EVM - since EVM is holding a lock until the
crypto initialisation is complete, this triggers a deadlock. Add a
CRYPTO_NOLOAD flag and skip module loading if it's set, and add that flag
in the EVM case in order to fail gracefully with an error message
instead of deadlocking.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
The RX SGL in processing is already registered with the RX SGL tracking
list to support proper cleanup. The cleanup code path uses the
sg_num_bytes variable which must therefore be always initialized, even
in the error code path.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Reported-by: syzbot+9c251bdd09f83b92ba95@syzkaller.appspotmail.com
#syz test: https://github.com/google/kmsan.git master
CC: <stable@vger.kernel.org> #4.14
Fixes: e870456d8e7c ("crypto: algif_skcipher - overhaul memory management")
Fixes: d887c52d6ae4 ("crypto: algif_aead - overhaul memory management")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The testmgr hash tests were testing init, digest, update and final
methods but not the finup method. Add a test for this one too.
While doing this, make sure we only run the partial tests once with
the digest tests and skip them with the final and finup tests since
they are the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some aead algorithms set .cra_flags = CRYPTO_ALG_TYPE_AEAD. But this is
redundant with the C structure type ('struct aead_alg'), and
crypto_register_aead() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the aead algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Many shash algorithms set .cra_flags = CRYPTO_ALG_TYPE_SHASH. But this
is redundant with the C structure type ('struct shash_alg'), and
crypto_register_shash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the shash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
sha512-generic and sha384-generic had a cra_priority of 0, so it wasn't
possible to have a lower priority SHA-512 or SHA-384 implementation, as
is desired for sha512_mb which is only useful under certain workloads
and is otherwise extremely slow. Change them to priority 100, which is
the priority used for many of the other generic algorithms.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
sha256-generic and sha224-generic had a cra_priority of 0, so it wasn't
possible to have a lower priority SHA-256 or SHA-224 implementation, as
is desired for sha256_mb which is only useful under certain workloads
and is otherwise extremely slow. Change them to priority 100, which is
the priority used for many of the other generic algorithms.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
sha1-generic had a cra_priority of 0, so it wasn't possible to have a
lower priority SHA-1 implementation, as is desired for sha1_mb which is
only useful under certain workloads and is otherwise extremely slow.
Change it to priority 100, which is the priority used for many of the
other generic algorithms.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
According to SP800-56A section 5.6.2.1, the public key to be processed
for the DH operation shall be checked for appropriateness. The check
shall covers the full verification test in case the domain parameter Q
is provided as defined in SP800-56A section 5.6.2.3.1. If Q is not
provided, the partial check according to SP800-56A section 5.6.2.3.2 is
performed.
The full verification test requires the presence of the domain parameter
Q. Thus, the patch adds the support to handle Q. It is permissible to
not provide the Q value as part of the domain parameters. This implies
that the interface is still backwards-compatible where so far only P and
G are to be provided. However, if Q is provided, it is imported.
Without the test, the NIST ACVP testing fails. After adding this check,
the NIST ACVP testing passes. Testing without providing the Q domain
parameter has been performed to verify the interface has not changed.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As of GCC 9.0.0 the build is reporting warnings like:
crypto/ablkcipher.c: In function ‘crypto_ablkcipher_report’:
crypto/ablkcipher.c:374:2: warning: ‘strncpy’ specified bound 64 equals destination size [-Wstringop-truncation]
strncpy(rblkcipher.geniv, alg->cra_ablkcipher.geniv ?: "<default>",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(rblkcipher.geniv));
~~~~~~~~~~~~~~~~~~~~~~~~~
This means the strnycpy might create a non null terminated string. Fix this by
explicitly performing '\0' termination.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: Nick Desaulniers <nick.desaulniers@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
According to SP800-56A section 5.6.2.1, the public key to be processed
for the ECDH operation shall be checked for appropriateness. When the
public key is considered to be an ephemeral key, the partial validation
test as defined in SP800-56A section 5.6.2.3.4 can be applied.
The partial verification test requires the presence of the field
elements of a and b. For the implemented NIST curves, b is defined in
FIPS 186-4 appendix D.1.2. The element a is implicitly given with the
Weierstrass equation given in D.1.2 where a = p - 3.
Without the test, the NIST ACVP testing fails. After adding this check,
the NIST ACVP testing passes.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The function skcipher_walk_next declared as static and marked as
EXPORT_SYMBOL_GPL. It's a bit confusing for internal function to be
exported. The area of visibility for such function is its .c file
and all other modules. Other *.c files of the same module can't use it,
despite all other modules can. Relying on the fact that this is the
internal function and it's not a crucial part of the API, the patch
just removes the EXPORT_SYMBOL_GPL marking of skcipher_walk_next.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove the original version of the VMAC template that had the nonce
hardcoded to 0 and produced a digest with the wrong endianness. I'm
unsure whether this had users or not (there are no explicit in-kernel
references to it), but given that the hardcoded nonce made it wildly
insecure unless a unique key was used for each message, let's try
removing it and see if anyone complains.
Leave the new "vmac64" template that requires the nonce to be explicitly
specified as the first 16 bytes of data and uses the correct endianness
for the digest.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently the VMAC template uses a "nonce" hardcoded to 0, which makes
it insecure unless a unique key is set for every message. Also, the
endianness of the final digest is wrong: the implementation uses little
endian, but the VMAC specification has it as big endian, as do other
VMAC implementations such as the one in Crypto++.
Add a new VMAC template where the nonce is passed as the first 16 bytes
of data (similar to what is done for Poly1305's nonce), and the digest
is big endian. Call it "vmac64", since the old name of simply "vmac"
didn't clarify whether the implementation is of VMAC-64 or of VMAC-128
(which produce 64-bit and 128-bit digests respectively); so we fix the
naming ambiguity too.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
syzbot reported a crash in vmac_final() when multiple threads
concurrently use the same "vmac(aes)" transform through AF_ALG. The bug
is pretty fundamental: the VMAC template doesn't separate per-request
state from per-tfm (per-key) state like the other hash algorithms do,
but rather stores it all in the tfm context. That's wrong.
Also, vmac_final() incorrectly zeroes most of the state including the
derived keys and cached pseudorandom pad. Therefore, only the first
VMAC invocation with a given key calculates the correct digest.
Fix these bugs by splitting the per-tfm state from the per-request state
and using the proper init/update/final sequencing for requests.
Reproducer for the crash:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int fd;
struct sockaddr_alg addr = {
.salg_type = "hash",
.salg_name = "vmac(aes)",
};
char buf[256] = { 0 };
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buf, 16);
fork();
fd = accept(fd, NULL, NULL);
for (;;)
write(fd, buf, 256);
}
The immediate cause of the crash is that vmac_ctx_t.partial_size exceeds
VMAC_NHBYTES, causing vmac_final() to memset() a negative length.
Reported-by: syzbot+264bca3a6e8d645550d3@syzkaller.appspotmail.com
Fixes: f1939f7c5645 ("crypto: vmac - New hash algorithm for intel_txt support")
Cc: <stable@vger.kernel.org> # v2.6.32+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The VMAC template assumes the block cipher has a 128-bit block size, but
it failed to check for that. Thus it was possible to instantiate it
using a 64-bit block size cipher, e.g. "vmac(cast5)", causing
uninitialized memory to be used.
Add the needed check when instantiating the template.
Fixes: f1939f7c5645 ("crypto: vmac - New hash algorithm for intel_txt support")
Cc: <stable@vger.kernel.org> # v2.6.32+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem fixes from James Morris:
- Smack: fix a regression caused by 1bbc55131e5
- X.509: fix a (usually un-seen) bug in RSA signature parsing
* 'fixes-v4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
X.509: unpack RSA signatureValue field from BIT STRING
Smack: Mark inode instant in smack_task_to_inode
|
|
The signatureValue field of a X.509 certificate is encoded as a BIT STRING.
For RSA signatures this BIT STRING is of so-called primitive subtype, which
contains a u8 prefix indicating a count of unused bits in the encoding.
We have to strip this prefix from signature data, just as we already do for
key data in x509_extract_key_data() function.
This wasn't noticed earlier because this prefix byte is zero for RSA key
sizes divisible by 8. Since BIT STRING is a big-endian encoding adding zero
prefixes has no bearing on its value.
The signature length, however was incorrect, which is a problem for RSA
implementations that need it to be exactly correct (like AMD CCP).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: c26fd69fa009 ("X.509: Add a crypto key parser for binary (DER) X.509 certificates")
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix use after free in chtls
- Fix RBP breakage in sha3
- Fix use after free in hwrng_unregister
- Fix overread in morus640
- Move sleep out of kernel_neon in arm64/aes-blk
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: core - Always drop the RNG in hwrng_unregister()
crypto: morus640 - Fix out-of-bounds access
crypto: don't optimize keccakf()
crypto: arm64/aes-blk - fix and move skcipher_walk_done out of kernel_neon_begin, _end
crypto: chtls - use after free in chtls_pt_recvmsg()
|
|
Trival fix to correct the indentation of a single statement
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds the sha384 pre-computed 0-length hash so that device
drivers can use it when an hardware engine does not support computing a
hash from a 0 length input.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
