| Age | Commit message (Collapse) | Author |
|---|
|
mmap()
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This config option isn't actually used anywhere and can be safely
removed. The last user was traps.c before commit 082f47a ([ARM]
always allow dump_stack() to produce a backtrace, 2007-07-05).
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
|
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Reported-by: Nick Bane <nickbane1@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Avoid to mismatch between NR_BUILTIN_GPIO and gpio interrupt number.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Avoid to mismatch between NR_BUILTIN_GPIO and GPIO interrupt number
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Bit[9:7] should always be zero in PXA168.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The patch below removes an unused config variable found by using a kernel
cleanup script.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
VFP registers d16-d31 are callee saved registers and must be preserved
during function calls, including fork(). The VFP configuration should
also be preserved. The patch copies the full VFP state to the child
process.
Reported-by: Paul Wright <paul.wright@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds THREAD_NOTIFY_COPY for calling registered handlers
during the copy_thread() function call. It also changes the VFP handler
to use a switch statement rather than if..else and ignore this event.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The HIGHPTE config option depends on !OUTER_CACHE. However, there is no
set_pte_ext() function that does outer cache maintenance by physical
address, hence no need for such restriction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit a737823d ("ARM: perf: ensure overflows aren't missed due to IRQ
latency") changed the way that event deltas are calculated on overflow
so that we don't miss events when the new count value overtakes the
previous one.
Unfortunately, we forget to count the event that passes through zero so
we end up being off by 1. This patch adds on the correction.
Reported-by: Chris Moore <moore@free.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Cc: stable <stable@kernel.org>
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] compile fix for latest binutils
[S390] cio: prevent purging of CCW devices in the online state
[S390] qdio: fix init sequence
[S390] Fix parameter passing for smp_switch_to_cpu()
[S390] oprofile s390: prevent stack corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
efifb: Add override for 11" Macbook Air 3,1
efifb: Support overriding fields FW tells us with the DMI data.
fb: Reduce priority of resource conflict message
savagefb: Remove obsolete else clause in savage_setup_i2c_bus
savagefb: Set up I2C based on chip family instead of card id
savagefb: Replace magic register address with define
drivers/video/bfin-lq035q1-fb.c: introduce missing kfree
video: s3c-fb: fix checkpatch errors and warning
efifb: support AMD Radeon HD 6490
s3fb: fix Virge/GX2
fbcon: Remove unused 'display *p' variable from fb_flashcursor()
fbdev: sh_mobile_lcdcfb: fix module lock acquisition
fbdev: sh_mobile_lcdcfb: add blanking support
viafb: initialize margins correct
viafb: refresh rate bug collection
sh: mach-ap325rxa: move backlight control code
sh: mach-ecovec24: support for main lcd backlight
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: arch-shmobile: only run FSI init on respective boards
ARM: arch-shmobile: only run HDMI init on respective boards
ARM: mach-shmobile: Correctly check for CONFIG_MACH_MACKEREL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: select ARCH_NO_SYSDEV_OPS.
sh: fix build error in board-sh7757lcr.c
sh: landisk: Remove whitespace
sh: landisk: Remove mv_nr_irqs
sh: sh-sci: Fix double initialization by serial_console_setup
serial: sh-sci: prevent setup of uninitialized serial console
dma: shdma: add checking the DMAOR_AE in sh_dmae_err
|
|
'timers-fixes-for-linus', 'irq-fixes-for-linus' and 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
|
|
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: move and fix substitue search for missing CPUID entries
KVM: fix XSAVE bit scanning
KVM: Enable async page fault processing
KVM: fix crash on irqfd deassign
|
|
* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6:
Fix common misspellings
|
|
The sfi_mrtc_array[] only gets initialized when the sfi mrtc
table is parsed, so the vrtc_paddr should be initalized after it
too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140389-27603-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
On 32bit systems without SSE (that is, they use FSAVE/FRSTOR for FPU
context switches), FPU exceptions in user mode cause Oopses, BUGs,
recursive faults and other nasty things:
fpu exception: 0000 [#1]
last sysfs file: /sys/power/state
Modules linked in: psmouse evdev pcspkr serio_raw [last unloaded: scsi_wait_scan]
Pid: 1638, comm: fxsave-32-excep Not tainted 2.6.35-07798-g58a992b-dirty #633 VP3-596B-DD/VT82C597
EIP: 0060:[<c1003527>] EFLAGS: 00010202 CPU: 0
EIP is at math_error+0x1b4/0x1c8
EAX: 00000003 EBX: cf9be7e0 ECX: 00000000 EDX: cf9c5c00
ESI: cf9d9fb4 EDI: c1372db3 EBP: 00000010 ESP: cf9d9f1c
DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
Process fxsave-32-excep (pid: 1638, ti=cf9d8000 task=cf9be7e0 task.ti=cf9d8000)
Stack:
00000000 00000301 00000004 00000000 00000000 cf9d3000 cf9da8f0 00000001
<0> 00000004 cf9b6b60 c1019a6b c1019a79 00000020 00000242 000001b6 cf9c5380
<0> cf806b40 cf791880 00000000 00000282 00000282 c108a213 00000020 cf9c5380
Call Trace:
[<c1019a6b>] ? need_resched+0x11/0x1a
[<c1019a79>] ? should_resched+0x5/0x1f
[<c108a213>] ? do_sys_open+0xbd/0xc7
[<c108a213>] ? do_sys_open+0xbd/0xc7
[<c100353b>] ? do_coprocessor_error+0x0/0x11
[<c12d5965>] ? error_code+0x65/0x70
Code: a8 20 74 30 c7 44 24 0c 06 00 03 00 8d 54 24 04 89 d9 b8 08 00 00 00 e8 9b 6d 02 00 eb 16 8b 93 5c 02 00 00 eb 05 e9 04 ff ff ff <9b> dd 32 9b e9 16 ff ff ff 81 c4 84 00 00 00 5b 5e 5f 5d c3 c6
EIP: [<c1003527>] math_error+0x1b4/0x1c8 SS:ESP 0068:cf9d9f1c
This usually continues in slight variations until the system is reset.
This bug was introduced by commit 58a992b9cbaf449aeebd3575c3695a9eb5d95b5e:
x86-32, fpu: Rewrite fpu_save_init()
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Link: http://lkml.kernel.org/r/1302106003-366952-1-git-send-email-hans.rosenfeld@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Restore the initialization of mmu_cr4_features during boot, which was
removed without comment in checkin e5f15b45ddf3afa2bbbb10c7ea34fb32b6de0a0e
x86: Cleanup highmap after brk is concluded
thereby breaking resume from hibernate. This restores previous
functionality in approximately the same place, and corrects the
reading of %cr4 on pre-CPUID hardware (%cr4 exists if and only if
CPUID is supported.)
However, part of the problem is that the hibernate suspend/resume
sequence should manage the save/restore of %cr4 explicitly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <201104020154.57136.rjw@sisk.pl>
|
|
Now that everything that was using these interfaces has been converted to
the syscore ops, prevent new code from using the old API.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If several boards are enabled in the kernel configuration,
fsi_init_pm_clock() functions from board-ap4evb.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
I made a bit of a thinko when adding Mackerel to the boards
that support zboot using MMCIF.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If KVM cannot find an exact match for a requested CPUID leaf, the
code will try to find the closest match instead of simply confessing
it's failure.
The implementation was meant to satisfy the CPUID specification, but
did not properly check for extended and standard leaves and also
didn't account for the index subleaf.
Beside that this rule only applies to CPUID intercepts, which is not
the only user of the kvm_find_cpuid_entry() function.
So fix this algorithm and call it from kvm_emulate_cpuid().
This fixes a crash of newer Linux kernels as KVM guests on
AMD Bulldozer CPUs, where bogus values were returned in response to
a CPUID intercept.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
When KVM scans the 0xD CPUID leaf for propagating the XSAVE save area
leaves, it assumes that the leaves are contigious and stops at the
first zero one. On AMD hardware there is a gap, though, as LWP uses
leaf 62 to announce it's state save area.
So lets iterate through all 64 possible leaves and simply skip zero
ones to also cover later features.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Signed-off-by: Matt Evans <matt@ozlabs.au.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Without this, "holes" in the CPU numbering can cause us to
free too many PACAs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit b3df895aebe091b1657 "powerpc/kexec: Add support for FSL-BookE"
introduced the original PPC_STD_MMU_64 checks around the function
crash_kexec_wait_realmode(). Then commit c2be05481f61252
"powerpc: Fix default_machine_crash_shutdown #ifdef botch" changed
the ifdef around the calling site to add a check on SMP, but the
ifdef around the function itself was left unchanged, leaving an
unused function for PPC_STD_MMU_64=y and SMP=n
Rather than have two ifdefs that can get out of sync like this,
simply put the corrected conditional around the function and use
a stub to get rid of one set of ifdefs completely.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix ftrace
microblaze: Wire up new syscalls
microblaze: Fix level/edge irq sensibility
|
|
Fix some minor typos:
* informations => information
* there own => their own
* these => this
Signed-off-by: Sylvestre Ledru <sylvestre.ledru@scilab.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Fix kdump reboot
x86, amd-nb: Rename CPU PCI id define for F4
sound: Add delay.h to sound/soc/codecs/sn95031.c
x86, mtrr, pat: Fix one cpu getting out of sync during resume
x86, microcode: Unregister syscore_ops after microcode unloaded
x86: Stop including <linux/delay.h> in two asm header files
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix task_struct reference leak
perf: Fix task context scheduling
perf: mmap 512 kiB by default
perf: Rebase max unprivileged mlock threshold on top of page size
perf tools: Fix NO_NEWT=1 python build error
perf symbols: Properly align symbol_conf.priv_size
perf tools: Emit clearer message for sys_perf_event_open ENOENT return
perf tools: Fixup exit path when not able to open events
perf symbols: Fix vsyscall symbol lookup
oprofile, x86: Allow setting EDGE/INV/CMASK for counter events
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: create new rcu_access_index() and use in mce
WARN_ON_SMP(): Add comment to explain ({0;})
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32
* 'unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32:
unicore32 framebuffer fix: get videomemory by __get_free_pages() and make it floatable
unicore32 core architecture: remove duplicated #include
unicore32 rtc driver fix: cleanup irq_set_freq and irq_set_state
unicore32 fix: remove arch-specific futex support
unicore32 ldscript fix: add cacheline parameter to PERCPU() macro
|
|
Commit d8fc3afc49 (x86, NUMA: Move *_numa_init() invocations
into initmem_init()) moved acpi_numa_init() call into NUMA
initmem_init() but forgot to update 32bit NUMA init breaking ACPI
NUMA configuration for 32bit.
acpi_numa_init() call was later moved again to srat_64.c. Match
it by adding the call to get_memcfg_from_srat() in srat_32.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <20110404100645.GE1420@mtj.dyndns.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Reported-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
PCIe memory address space is 1:1 mapped with u-boot.
Update dts of Px020RDB i.e. P1020RDB and P2020RDB to match the address map
changes in u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The latest binutils won't accept the stfl instruction with march=g5
which is the correct behaviour. Unfortunately head.S is assembled
with -march=g5 even if the target cpu is z900 or later. To get
31-bit kernels compiled again the easiest fix is to use the .insn
notation for the stfl instruction in head.S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
After the execution has been switched to the destination CPU, the target
function is called with the wrong parameter. According to the C calling
convention on s390, the first parameter should be loaded into register 2.
Currently in smp_restart_cpu() it is stored in register 3. To fix this, we
load the parameter into the correct register 2.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Prevent stack corruption by memcpy which copies more bytes then
available at the destination. While at it use the new test_facility
to test for the facility bit.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Offering CONFIG_PM_SLEEP for CPUs which do not support suspend leads to
build errors, so only set CONFIG_ARCH_SUSPEND_POSSIBLE if we have a CPU
selected which supports suspend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
CONFIG_PM is now set whenever we support either runtime PM in addition
to suspend and hibernate. This causes build errors when runtime PM is
enabled on a platform, but the CPU does not have the appropriate support
for suspend.
So, switch this code to use CONFIG_PM_SLEEP rather than CONFIG_PM to
allow runtime PM to be enabled without causing build errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
floatable
1. get videomemory by __get_free_pages() in fb-puv3.c
2. remove resource reservation for old fixed UNIGFX_MMAP & UVC_MMAP space
3. remove unused macros: PKUNTIY_UNIGFX_MMAP_BASE, PKUNITY_UNIGFX_MMAP_SIZE,
PKUNITY_UVC_MMAP_BASE, PKUNITY_UVC_MMAP_SIZE and KUSER_UNIGFX_BASE
4. remove unused header linux/vmalloc.h in fb-puv3.h
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove duplicated #include('s) in
arch/unicore32/kernel/traps.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
|
