| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 10f4dc8b27ac42f930ac55adb8c521264dc997f8.
Quoth Andi Kleen:
"Kiran decided that it makes the problem worse than it was before.
Fixing it fully requires more work which is too much for 2.6.16. So
please revert that commit for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch contains a printk reorder to remove the current problem of
displaying "PCI-DMA: Disabling IOMMU." and then "PCI-DMA: using GART
IOMMU" 20 lines later in dmesg.
It also constains a printk reorder in swiotlb to state swiotlb
enablement prior to describing the location of the bounce buffers, and a
printk reorder to state gart enablement prior to describing the
aperature.
Also constains a whitespace cleanup in arch/x86_64/kernel/setup.c
Tested (along with patch 2/2) on dual opteron with gart enabled,
iommu=soft, and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Hack for 2.6.16. In 2.6.17 all code that uses NR_CPUs should
be audited and changed to only touch possible CPUs.
Don't mark the reference per cpu data init data (so it stays
around after boot) and point all impossible CPUs to it. This way
they reference some valid - although shared memory. Usually
this is only initialization like INIT_LIST_HEADs and there
won't be races because these CPUs never run. Still somewhat hackish.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
not enabled
It's bad juju to touch the APIC when it hasn't been enabled.
I also moved ack_bad_irq for x86-64 out of line following i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Checking of the validity of pointers should be consistently done before
dereferencing the pointer.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Conditionalize two unwind directives to match other similarly
conditional code.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Cc: Jim Houston <jim.houston@ccur.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
On some broken motherboards (at least one NForce3 based AMD64 laptop)
the PIT timer runs at a incorrect frequency. This patch adds a new
option "apicpmtimer" that allows to use the APIC timer and calibrate it
using the PMTimer. It requires the earlier patch that allows to run the
main timer from the APIC.
Specifying apicpmtimer implies apicmaintimer.
The option defaults to off for now.
I tested it on a few systems and the resulting APIC timer frequencies
were usually a bit off, but always <1%, which should be tolerable.
TBD figure out heuristic to enable this automatically on the affected
systems TBD perhaps do it on all NForce3s or using DMI?
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
kprobes cannot deal with the funny calling conventions when it
runs on a different stack when it returns. If someone wants
to instrument context switch they can add a probe to schedule()
instead.
Cc: jkenisto@us.ibm.com, prasanna@in.ibm.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Align the start of the per-cpu section to the configured number of bytes in a
cache line. This stops a BUG_ON() from triggering in load_module() when
DEFINE_PER_CPU() is used in a module and the section isn't cacheline-aligned.
Rusty also found this and sent a patch in a while ago
(http://lkml.org/lkml/2004/10/19/17), I don't know what came of that.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
merge
[ AK: I redid Kevin's fix to be simpler, but the idea and original
analysis of the problem is from Kevin]
This avoid allocation failures on some SATA systems like Nvidia CK8
when the IOMMU gets fragmented. Modern SATA devices have quite large queues
(128 entries) and the FS with ext2/3 is good enough now that it often
passes whole 128 page sg lists down to the driver. These require
512K of continuous free space in the IOMMU aperture to map when merged.
When the IOMMU is fragmented this could lead to spurious IO errors
due to failing mappings.
Short term fix is to just try to map the SG list again unmerged
page by page - this way fragmentation doesn't matter anymore.
The code for that was already there, but it just wasn't enabled for the
merge case.
According to Kevin at least the Nvidia device doesn't seem to benefit
from merging much anyways, so the only slowdown is from trying
to do an unnecessary merge attempt.
Kevin plans to implement better fragmentation avoidance in the future,
but that wouldn't be 2.6.16 material.
TBD: should add some statistic counters to count how often that really
happens.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I broke this earlier when moving the patch from i386 to x86-64.
Need to return the virtual address here, not the physical address.
This fixes some boot time crashes on x86-64.
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- Check if the processor/memory affinity entries are long enough
according to the ACPI 3.0 spec.
- Ignore memory affinity entries that define a zero length region.
All based on BIOS issues found in the field @)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
attached patch is 2 more cases i found via running the reference_init.pl
script. These were easy to spot just knowing the file names. There is
one another about init/main.c that i cant exactly zero in. (partly
because i dont know how to interpret the data thats spewed out of the tool).
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
SIgned-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Might fix boot failures on systems with empty PXMs in SRAT
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It has been enabled by default for some time now and is cheap enough
so it doesn't matter anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently, x86_64 and ia64 arches do not clear the corresponding bits
in the node's cpumask when a cpu goes down or cpu bring up is cancelled.
This is buggy since there are pieces of common code where the cpumask is
checked in the cpu down code path to decide on things (like in the slab
down path). PPC does the right thing, but x86_64 and ia64 don't (This
was the reason Sonny hit upon a slab bug during cpu offline on ppc and
could not reproduce on other arches). This patch fixes it for x86_64.
I won't attempt ia64 as I cannot test it.
Credit for spotting this should go to Alok.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
functions
They cause quite bad performance regressions on Netburst
This is temporary until we can get new optimized functions
for these CPUs.
This undoes changes that were done in 2.6.15 and in 2.6.16-rc1,
essentially bringing the code back to 2.6.14 level. Only change
is I renamed the X86_FEATURE_K8_C flag to X86_FEATURE_REP_GOOD
and fixed the check for the flag and also fixed some comments.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This avoids BUG_ONs in the low level allocator when an illegal
GFP mask is added.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
At resume time, TSC's value or something similar might be changed a lot
against suspend time. This could make system gets a very big lost ticks.
See http://bugzilla.kernel.org/show_bug.cgi?id=5825
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
They all have problems with IRQ 0 routing, so just use the APIC on them.
Can be overwritten with "noapicmaintimer"
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Another piece from the no-idle-tick patch.
This can be enabled with the "apicmaintimer" option.
This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.
It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.
It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.
Requires earlier bugfix from Venkatesh
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
A kprobe executes IRET early and that could cause NMI recursion
and stack corruption.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
|
|
This assembly version is measurably faster than the generic version in
lib/iomap_copy.c.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We need to use the compat function here.
Pointer out by Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Handle more bogus MCFG entries
Some Asus P4 boards seem to have broken MCFG tables with
only a single entry for busses 0-0. Special case these
and assume they mean all busses can be accessed.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
branches into release
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Wire up the x86_64 syscalls.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix a typo/mis-merge in one of the previous patches.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Add x86-64 specific memory hot-add functions, Kconfig options,
and runtime kernel page table update functions to make
hot-add usable on x86-64 machines. Also, fixup the nefarious
conditional locking and exports pointed out by Andi.
Tested on Intel and IBM x86-64 memory hot-add capable systems.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Another try at this.
For 32bit follow the 32bit implementation from Ingo -
mappings are growing down from the end of stack now
and vary randomly by 1GB.
Randomized mappings for 64bit just vary the normal mmap break
by 1TB. I didn't bother implementing full flex mmap for 64bit
because it shouldn't be needed there.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It's identical to the standard elf_map.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
... as they are no longer needed. Since there were hard-coded numbers in the
file, the patch also adds a mechanism to avoid these (otherwise potential
future changes would again and again require adjusting these numbers).
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The comparison of the initrd start address against "&_end" is
unnecessary and incorrect. Make it match the x86 code that just
compares the passed-in arguments.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
For not fully explained reasons it broke mem=... on several setups.
Also minor cleanup.
Cc: axboe@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
'check_efer' uses 'do_not_nx'. Hotpluged CPU could wrongly disable NX.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
uses correct lapic base address. The set_fixmap appears useless.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
To avoid mistakes.
I got a few reports where people got broken timing because they didn't
have the PMTIMER fallback.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This unbreaks recursive kprobes which didn't work anymore
due to an earlier patch which converted the debug entry point
to use an IST.
This also allows nesting of the debug entry point too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
o This fix was posted for i386 long back. Posting it for x86_64.
http://marc.theaimsgroup.com/?l=linux-kernel&m=110380103229830&w=2
o This patch fixes the problem of secondary cpus boot up. This situation
is faced when kernel is built for default locations like 16MB and
onwards. In this configuration, only primary cpu (BP) comes and
secondary cpus don't boot.
o Problem occurs because in trampoline code, lgdt is not able to load the
GDT as it happens to be situated beyond 16MB. This is due to the fact
that cpu is still in real mode and default operand size is 16bit.
o This patch uses lgdtl instead of lgdt to force operand size to 32
instead of 16.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Handling common prefixes is tricky.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
... reducing the amount of changes Xen has to do.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The explicit and implicit calls to setup_early_printk() were passing
inconsistent arguments.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
