| Age | Commit message (Collapse) | Author |
|---|
|
This enables us to avoid printing swiotlb memory info when we
initialize swiotlb. After swiotlb initialization, we could find
that we don't need swiotlb.
This patch removes the code to print swiotlb memory info in
swiotlb_init() and exports the function to do that.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
Cc: tony.luck@intel.com
Cc: benh@kernel.crashing.org
LKML-Reference: <1257849980-22640-9-git-send-email-fujita.tomonori@lab.ntt.co.jp>
[ -v2: merge up conflict ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Remove the reliance on a staticly defined NVRAM size, allowing
platforms to support NVRAMs with sizes differing from the standard.
A fall back value is provided for platforms not supporting this extension.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Based on initial work from: Dale Farnsworth <dale@farnsworth.org>
Add the low level irq tracing hooks for 32-bit powerpc needed
to enable full lockdep functionality.
The approach taken to deal with the code in entry_32.S is that
we don't trace all the transitions of MSR:EE when we just turn
it off to peek at TI_FLAGS without races. Only when we are
calling into C code or returning from exceptions with a state
that have changed from what lockdep thinks.
There's a little bugger though: If we take an exception that
keeps interrupts enabled (such as an alignment exception) while
interrupts are enabled, we will call trace_hardirqs_on() on the
way back spurriously. Not a big deal, but to get rid of it would
require remembering in pt_regs that the exception was one of the
type that kept interrupts enabled which we don't know at this
stage. (Well, we could test all cases for regs->trap but that
sucks too much).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch includes the basic infrastructure to use swiotlb
bounce buffering on 32-bit powerpc. It is not yet enabled on
any platforms. Probably the most interesting bit is the
addition of addr_needs_map to dma_ops - we need this as
a dma_op because the decision of whether or not an addr
can be mapped by a device is device-specific.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Wire up the trampoline code for ppc32 to relay exceptions from the
vectors at address 0 to vectors at address 32MB, and modify Kconfig
to enable Kdump support for all classic powerpcs.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This makes the MMU context code used for CPUs with no hash table
(except 603) dynamically allocate the various maps used to track
the state of contexts.
Only the main free map and CPU 0 stale map are allocated at boot
time. Other CPU maps are allocated when those CPUs are brought up
and freed if they are unplugged.
This also moves the initialization of the MMU context management
slightly later during the boot process, which should be fine as
it's really only needed when userland if first started anyways.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We're soon running out of CPU features and I need to add some new
ones for various MMU related bits, so this patch separates the MMU
features from the CPU features. I moved over the 32-bit MMU related
ones, added base features for MMU type families, but didn't move
over any 64-bit only feature yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
smp_hw_index isn't used on 64-bit, so move it from smp.c to
setup_32.c.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The `have_of' variable is a relic from the arch/ppc time, it isn't
useful nowadays.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The "phys" argument to machine_init() isn't used and isn't likely to
ever be so let's remove it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The file arch/powerpc/kernel/sysfs.c is currently only compiled for
64-bit kernels. It contain code to register CPU sysdevs in sysfs and
add various properties such as cache topology and raw access by root
to performance monitor counters (PMCs). A lot of that can be re-used
as is on 32-bits.
This makes the file be built for both, with appropriate ifdef'ing
for the few bits that are really 64-bit specific, and adds some
support for the raw PMCs for 75x and 74xx processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch removes the old kgdb reminants from ARCH=powerpc and
implements the new style arch specific stub for the common kgdb core
interface.
It is possible to have xmon and kgdb in the same kernel, but you
cannot use both at the same time because there is only one set of
debug hooks.
The arch specific kgdb implementation saves the previous state of the
debug hooks and restores them if you unconfigure the kgdb I/O driver.
Kgdb should have no impact on a kernel that has no kgdb I/O driver
configured.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Manual fixup of:
arch/powerpc/Kconfig
|
|
To allow for a single kernel image on e500 v1/v2/mc we need to fixup lwsync
at runtime. On e500v1/v2 lwsync causes an illop so we need to patch up
the code. We default to 'sync' since that is always safe and if the cpu
is capable we will replace 'sync' with 'lwsync'.
We introduce CPU_FTR_LWSYNC as a way to determine at runtime if this is
needed. This flag could be moved elsewhere since we dont really use it
for the normal CPU_FTR purpose.
Finally we only store the relative offset in the fixup section to keep it
as small as possible rather than using a full fixup_entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The e500 core enter DOZE/NAP power-saving modes when the core go to
cpu_idle routine.
The power management default running mode is DOZE, If the user
echo 1 > /proc/sys/kernel/powersave-nap
the system will change to NAP running mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
For the additonal exception levels (critical, debug, machine check) on
40x/book-e we were using "static" allocations of the stack in the
associated head.S.
Move to a runtime allocation to make the code a bit easier to read as
we mimic how we handle IRQ stacks. Its also a bit easier to setup the
stack with a "dummy" thread_info in C code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
|
|
This patch cleans up the ftrace code in PowerPC based on the comments from
Michael Ellerman.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: proski@gnu.org
Cc: a.p.zijlstra@chello.nl
Cc: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linuxppc-dev@ozlabs.org
Cc: Soeren Sandmann Pedersen <sandmann@redhat.com>
Cc: paulus@samba.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch adds full support for ftrace for PowerPC (both 64 and 32 bit).
This includes dynamic tracing and function filtering.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This makes it possible to use separate stacks for hard and soft IRQs
on 32-bit powerpc as well as on 64-bit. The code for 32-bit is just
the 32-bit analog of the 64-bit code.
* Added allocation and initialization of the irq stacks. We limit the
stacks to be in lowmem for ppc32.
* Implemented ppc32 versions of call_do_softirq() and call_handle_irq()
to switch the stack pointers
* Reworked how we do stack overflow detection. We now keep around the
limit of the stack in the thread_struct and compare against the limit
to see if we've overflowed. We can now use this on ppc64 if desired.
[ paulus@samba.org: Fixed bug on 6xx where we need to reload r9 with the
thread_info pointer. ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
|
|
* Add special cases for pplus and prep to ide_default_{irq,io_base}()
(+ FIXMEs about the need to use IDE platform host driver instead).
* Remove no longer needed ppc_ide_md and struct ide_machdep_calls.
* Then remove <linux/ide.h> include from:
- arch/powerpc/kernel/setup_32.c
- arch/ppc/kernel/ppc_ksyms.c
- arch/ppc/kernel/setup.c
- arch/ppc/platforms/pplus.c
- arch/ppc/platforms/prep_setup.c
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* PAGE_OFFSET is not always the start of code, use _stext instead.
* grab PAGE_SIZE and KERNELBASE from asm/page.h like ppc64 does. Makes the
code a bit more common and provide a single place to manipulate the
defines for things like kdump.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Old-world powermacs don't set L2CR or L3CR on processor upgrade cards.
This simple patch allows the setting of L3CR via a kernel parameter
(like the existing kernel parameter to set L2CR).
Signed-off-by: Robert Brose <bob@qbjnet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This allows platforms which don't have anything to do at setup_arch time
(like a bunch of the 4xx platforms) to eliminate an empty setup_arch hook.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
These are the symptom error messages:
CC arch/powerpc/kernel/setup_32.o
In file included from include/linux/blkdev.h:17,
from include/linux/ide.h:13,
from arch/powerpc/kernel/setup_32.c:13:
include/linux/bsg.h:67: warning: 'struct request_queue' declared inside parameter list
include/linux/bsg.h:67: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/bsg.h:71: warning: 'struct request_queue' declared inside parameter list
In file included from arch/powerpc/kernel/setup_32.c:13:
include/linux/ide.h:857: error: field 'wrq' has incomplete type
CC arch/powerpc/kernel/ppc_ksyms.o
In file included from include/linux/blkdev.h:17,
from include/linux/ide.h:13,
from arch/powerpc/kernel/ppc_ksyms.c:15:
include/linux/bsg.h:67: warning: 'struct request_queue' declared inside parameter list
include/linux/bsg.h:67: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/bsg.h:71: warning: 'struct request_queue' declared inside parameter list
In file included from arch/powerpc/kernel/ppc_ksyms.c:15:
include/linux/ide.h:857: error: field 'wrq' has incomplete type
The fix tries to use the smallest scope CONFIG_* symbols that will fix
the build problem. In this case <linux/ide.h> needs to be included
only if IDE=y or IDE=m were selected. Also, ppc_ide_md is needed only
if BLK_DEV_IDE=y or BLK_DEV_IDE=m
Moved the EXPORT_SYMBOL(ppc_ide_md) from ppc_ksysms.c next to its
declaration in setup_32.c which made <linux/ide.h> not needed. With
<linux/ide.h> gone from ppc_ksyms.c, <asm/cacheflush.h> is needed to
address the following warnings and errors:
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:122: error: '__flush_icache_range' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:122: warning: type defaults to 'int' in declaration of '__flush_icache_range'
arch/powerpc/kernel/ppc_ksyms.c:123: error: 'flush_dcache_range' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:123: warning: type defaults to 'int' in declaration of 'flush_dcache_range'
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove includes of files that existed in arch/ppc that we dont need in
arch/powerpc anymore. The following includes were removed:
<asm/amigappc.h>
<asm/bootinfo.h>
<asm/ppcboot.h>
<asm/ppc_sys.h>
<asm/residual.h>
<asm/m8260_pci.h>
This also caused platforms/embedded6xx/mpc7448_hpc2.h to no longer be
needed and thus removed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially). It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.
In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).
This tries to clarify the situation a little. The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified. We check this, instead of
SPLIT_ID_CACHE nearly everywhere.
The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200. In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature. The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.
This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
72486f1f8f0a2bc828b9d30cf4690cf2dd6807fc inverted the sense for enabling
hotplug CPU controls without reference to any other architecture other than
i386, ia64 and PowerPC. This left everyone else without hotplug CPU control.
Fix powerpc for this brain damage.
(akpm: patch adapted from rmk's ARM fix. Changelog stolen from rmk)
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently, early_init() in setup_32.c zeroes from '_bss_start' to '_end'.
It should only zero from '__bss_start' to '__bss_stop'. This patch does that.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
udbg_early_init() is a function used on 64 bit systems, which
initializes whichever early udbg backend is configured. This function
is not called on 32-bit, however if btext early debug is enabled it
does have an explicit, inline, #ifdef-ed assignment performing
analagous initialization.
This patch makes things more uniform by folding the btext
initialization as an option into udbg_early_init() and calling that
from the 32-bit setup path.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The following macro :
include/asm-powerpc/vga.h:#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
is used by drivers/video/console/vgacon.c which can be compiled as a module
(drivers/video/vga16fb.ko).
Therefore, vgacon_remap_base should be exported.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
dev_t boot_dev is declared in arch/powerpc/kernel/setup_32.c
and in arch/powerpc/kernel/setup_64.c but not used in these files.
It is only used in arch/powerpc/platforms/powermac/setup.c, so make
it static in this file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch reworks the feature fixup mecanism so vdso's can be fixed up.
The main issue was that the construct:
.long label (or .llong on 64 bits)
will not work in the case of a shared library like the vdso. It will
generate an empty placeholder in the fixup table along with a reloc,
which is not something we can deal with in the vdso.
The idea here (thanks Alan Modra !) is to instead use something like:
1:
.long label - 1b
That is, the feature fixup tables no longer contain addresses of bits of
code to patch, but offsets of such code from the fixup table entry
itself. That is properly resolved by ld when building the .so's. I've
modified the fixup mecanism generically to use that method for the rest
of the kernel as well.
Another trick is that the 32 bits vDSO included in the 64 bits kernel
need to have a table in the 64 bits format. However, gas does not
support 32 bits code with a statement of the form:
.llong label - 1b (Or even just .llong label)
That is, it cannot emit the right fixup/relocation for the linker to use
to assign a 32 bits address to an .llong field. Thus, in the specific
case of the 32 bits vdso built as part of the 64 bits kernel, we are
using a modified macro that generates:
.long 0xffffffff
.llong label - 1b
Note that is assumes that the value is negative which is enforced by
the .lds (those offsets are always negative as the .text is always
before the fixup table and gas doesn't support emiting the reloc the
other way around).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
There are currently two versions of the functions for applying the
feature fixups, one for CPU features and one for firmware features. In
addition, they are both in assembly and with separate implementations
for 32 and 64 bits. identify_cpu() is also implemented in assembly and
separately for 32 and 64 bits.
This patch replaces them with a pair of C functions. The call sites are
slightly moved on ppc64 as well to be called from C instead of from
assembly, though it's a very small change, and thus shouldn't cause any
problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
My patch to make the early xmon logic work with earlier early param
parsing (480f6f35a149802a94ad5c1a2673ed6ec8d2c158) breaks xmon=off.
No one does this obviously as xmon rocks, but it should really work
as documented.
While fixing that it struck me that we could move the xmon param
handling into xmon.c, and also consolidate the
xmon_init()/do_early_xmon logic into xmon_setup(). This means
xmon=early drops into xmon a little earlier on 32-bit, but it
seems to work just fine.
Tested on PSERIES and CLASSIC32.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove unused global SYSRQ_KEY from ppc and powerpc
Remove unused define SYSRQ_KEY from sh/sh64 and h8300
Remove unused pckbd_sysrq_xlate and kbd_sysrq_xlate usage
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch fixes various issues with offb (the default fbdev used on
powerpc when no proper fbdev is supported). It was broken when using
BootX under some circumstances and would fail to properly get the
framebuffer base address in others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently we have call parse_early_param() earliyish, but not really very
early. In particular, it's not early enough to do things like mem=x or
crashkernel=blah, which is annoying.
So do it earlier. I've checked all the early param handlers, and none of them
look like they should have any trouble with this. I haven't tested the
booke_wdt ones though.
On 32-bit we were doing the CONFIG_CMDLINE logic twice, so don't.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently early_xmon() calls directly into debugger() if xmon=early is passed.
This ties the invocation of early xmon to the location of parse_early_param(),
which might change.
Tested on P5 LPAR and F50.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Allow boards to provide a panic callback on ppc32. Moved the code to sets
this up into setup-common.c so its shared between ppc32 & ppc64. Also moved
do_init_bootmem prototype into setup.h.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Removed platform_init usage on 83xx and 85xx and use define_machine and
probe(). For now we always return true in the problem since you can only
build for one specific board at a time. This is an artificial constraint.
When we get ride of it we will need to update the Kconfig's for these
sub-arch's and make the board's probe() functions actually do something.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
OCP isn't used in arch/powerpc and hopefully will never be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This unifies the 32-bit (ARCH=ppc and ARCH=powerpc) and 64-bit idle
loops. It brings over the concept of having a ppc_md.power_save
function from 32-bit to ARCH=powerpc, which lets us get rid of
native_idle(). With this we will also be able to simplify the idle
handling for pSeries and cell.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
