| Age | Commit message (Collapse) | Author |
|---|
|
This commit fixes a "maybe-uninitialized" build failure in
arch/mips/kvm/tlb.c when KVM, DYNAMIC_DEBUG and JUMP_LABEL are all
enabled. The failure is:
In file included from ./include/linux/printk.h:329:0,
from ./include/linux/kernel.h:13,
from ./include/asm-generic/bug.h:15,
from ./arch/mips/include/asm/bug.h:41,
from ./include/linux/bug.h:4,
from ./include/linux/thread_info.h:11,
from ./include/asm-generic/current.h:4,
from ./arch/mips/include/generated/asm/current.h:1,
from ./include/linux/sched.h:11,
from arch/mips/kvm/tlb.c:13:
arch/mips/kvm/tlb.c: In function ‘kvm_mips_host_tlb_inv’:
./include/linux/dynamic_debug.h:126:3: error: ‘idx_kernel’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_pr_debug(&descriptor, pr_fmt(fmt), \
^~~~~~~~~~~~~~~~~~
arch/mips/kvm/tlb.c:169:16: note: ‘idx_kernel’ was declared here
int idx_user, idx_kernel;
^~~~~~~~~~
There is a similar error relating to "idx_user". Both errors were
observed with GCC 6.
As far as I can tell, it is impossible for either idx_user or idx_kernel
to be uninitialized when they are later read in the calls to kvm_debug,
but to satisfy the compiler, add zero initializers to both variables.
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Fixes: 57e3869cfaae ("KVM: MIPS/TLB: Generalise host TLB invalidate to kernel ASID")
Cc: <stable@vger.kernel.org> # 4.11+
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Set up hardware virtualisation on Octeon III cores, configuring guest
interrupt routing and carving out half of the root TLB for guest use,
restoring it back again afterwards.
We need to be careful to inhibit TLB shutdown machine check exceptions
while invalidating guest TLB entries, since TLB invalidation is not
available so guest entries must be invalidated by setting them to unique
unmapped addresses, which could conflict with mappings set by the guest
or root if recently repartitioned.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
When TLB entries are invalidated in the presence of a virtually tagged
icache, such as that found on Octeon CPUs, flush the icache so that we
don't get a reserved instruction exception even though the TLB mapping
is removed.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Add the main support for the MIPS Virtualization ASE (A.K.A. VZ) to MIPS
KVM. The bulk of this work is in vz.c, with various new state and
definitions elsewhere.
Enough is implemented to be able to run on a minimal VZ core. Further
patches will fill out support for guest features which are optional or
can be disabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
|
|
Add functions for MIPS VZ TLB management to tlb.c.
kvm_vz_host_tlb_inv() will be used for invalidating root TLB entries
after GPA page tables have been modified due to a KVM page fault. It
arranges for a root GPA mapping to be flushed from the TLB, using the
gpa_mm ASID or the current GuestID to do the probe.
kvm_vz_local_flush_roottlb_all_guests() and
kvm_vz_local_flush_guesttlb_all() flush all TLB entries in the
corresponding TLB for guest mappings (GPA->RPA for root TLB with
GuestID, and all entries for guest TLB). They will be used when starting
a new GuestID cycle, when VZ hardware is enabled/disabled, and also when
switching to a guest when the guest TLB contents may be stale or belong
to a different VM.
kvm_vz_guest_tlb_lookup() converts a guest virtual address to a guest
physical address using the guest TLB. This will be used to decode guest
virtual addresses which are sometimes provided by VZ hardware in
CP0_BadVAddr for certain exceptions when the guest physical address is
unavailable.
kvm_vz_save_guesttlb() and kvm_vz_load_guesttlb() will be used to
preserve wired guest VTLB entries while a guest isn't running.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Use the lockless GVA helpers to implement the reading of guest
instructions for emulation. This will allow it to handle asynchronous
TLB flushes when they are implemented.
This is a little more complicated than the other two cases (get_inst()
and dynamic translation) due to the need to emulate the appropriate
guest TLB exception when the address isn't present or isn't valid in the
guest TLB.
Since there are several protected cache ops that may need to be
performed safely, this is abstracted by kvm_mips_guest_cache_op() which
is passed a protected cache op function pointer and takes care of the
lockless operation and fault handling / retry if the op should fail,
taking advantage of the new errors which the protected cache ops can now
return. This allows the existing advance fault handling which relied on
host TLB lookups to be removed, along with the now unused
kvm_mips_host_tlb_lookup(),
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
When exceptions are injected into the MIPS KVM guest, the whole host TLB
is flushed (except any entries in the guest KSeg0 range). This is
certainly not mandated by the architecture when exceptions are taken
(userland can't directly change TLB mappings anyway), and is a pretty
heavyweight operation:
- There may be hundreds of TLB entries especially when a 512 entry FTLB
is present. These are walked and read and conditionally invalidated,
so the TLBINV feature can't be used either.
- It'll indiscriminately wipe out entries belonging to other memory
spaces. A simple ASID regeneration would be much faster to perform,
although it'd wipe out the guest KSeg0 mappings too.
My suspicion is that this was simply to plaster over the fact that
kvm_mips_host_tlb_inv() incorrectly only invalidated TLB entries in the
ASID for guest usermode, and not the ASID for guest kernelmode.
Now that the recent commit "KVM: MIPS/TLB: Flush host TLB entry in
kernel ASID" fixes kvm_mips_host_tlb_inv() to flush TLB entries in the
kernelmode ASID when the guest TLB changes, lets drop these calls and
the otherwise unused kvm_mips_flush_host_tlb().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Now that KVM no longer uses wired entries we can safely use
local_flush_tlb_all() when we need to flush the entire TLB (on the start
of a new ASID cycle). This doesn't flush wired entries, which allows
other code to use them without KVM clobbering them all the time. It also
is more up to date, knowing about the tlbinv architectural feature,
flushing of micro TLB on cores where that is necessary (Loongson I
believe), and knows to stop the HTW while doing so.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Now that the commpage doesn't use wired TLB entries, the per-CPU
vm_init() callback is the only work done by kvm_mips_init_vm_percpu().
The trap & emulate implementation doesn't actually need to do anything
from vm_init(), and the future VZ implementation would be better served
by a kvm_arch_hardware_enable callback anyway.
Therefore drop the vm_init() callback entirely, allowing the
kvm_mips_init_vm_percpu() function to also be dropped, along with the
kvm_mips_instance atomic counter.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Now that we have GVA page tables and an optimised TLB refill handler in
place, convert the handling of commpage faults from the guest kernel to
fill the GVA page table and invalidate the TLB entry, rather than
filling the wired TLB entry directly.
For simplicity we no longer use a wired entry for the commpage (refill
should be much cheaper with the fast-path handler anyway). Since we
don't need to manipulate the TLB directly any longer, move the function
from tlb.c to mmu.c. This puts it closer to the similar functions
handling KSeg0 and TLB mapped page faults from the guest.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Now that we have GVA page tables and an optimised TLB refill handler in
place, convert the handling of page faults in TLB mapped segment from
the guest to fill a single GVA page table entry and invalidate the TLB
entry, rather than filling a TLB entry pair directly.
Also remove the now unused kvm_mips_get_{kernel,user}_asid() functions
in mmu.c and kvm_mips_host_tlb_write() in tlb.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Refactor kvm_mips_host_tlb_inv() to also be able to invalidate any
matching TLB entry in the kernel ASID rather than assuming only the TLB
entries in the user ASID can change. Two new bool user/kernel arguments
allow the caller to indicate whether the mapping should affect each of
the ASIDs for guest user/kernel mode.
- kvm_mips_invalidate_guest_tlb() (used by TLBWI/TLBWR emulation) can
now invalidate any corresponding TLB entry in both the kernel ASID
(guest kernel may have accessed any guest mapping), and the user ASID
if the entry being replaced is in guest USeg (where guest user may
also have accessed it).
- The tlbmod fault handler (and the KSeg0 / TLB mapped / commpage fault
handlers in later patches) can now invalidate the corresponding TLB
entry in whichever ASID is currently active, since only a single page
table will have been updated anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
kvm_mips_host_tlb_inv() uses the TLBP instruction to probe the host TLB
for an entry matching the given guest virtual address, and determines
whether a match was found based on whether CP0_Index > 0. This is
technically incorrect as an index of 0 (with the high bit clear) is a
perfectly valid TLB index.
This is harmless at the moment due to the use of at least 1 wired TLB
entry for the KVM commpage, however we will soon be ridding ourselves of
that particular wired entry so lets fix the condition in case the entry
needing invalidation does land at TLB index 0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Set init_mm as the active_mm and update mm_cpumask(current->mm) to
reflect that it isn't active when in guest context. This prevents cache
management code from attempting cache flushes on host virtual addresses
while in guest context, for example due to a cache management IPIs or
later when writing of dynamically translated code hits copy on write.
We do this using helpers in static kernel code to avoid having to export
init_mm to modules.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
The kvm_vcpu_arch structure contains both mm_structs for allocating MMU
contexts (primarily the ASID) but it also copies the resulting ASIDs
into guest_{user,kernel}_asid[] arrays which are referenced from uasm
generated code.
This duplication doesn't seem to serve any purpose, and it gets in the
way of generalising the ASID handling across guest kernel/user modes, so
lets just extract the ASID straight out of the mm_struct on demand, and
in fact there are convenient cpu_context() and cpu_asid() macros for
doing so.
To reduce the verbosity of this code we do also add kern_mm and user_mm
local variables where the kernel and user mm_structs are used.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
KVM sometimes flushes host TLB entries, reading each one to check if it
corresponds to a guest KSeg0 address. In the absence of EntryHi.EHInv
bits to invalidate the whole entry, the entries will be set to unique
virtual addresses in KSeg0 (which is not TLB mapped), spaced 2*PAGE_SIZE
apart.
The TLB read however will clobber the CP0_PageMask register with
whatever page size that TLB entry had, and that same page size will be
written back into the TLB entry along with the unique address.
This would cause breakage when transparent huge pages are enabled on
64-bit host kernels, since huge page entries will overlap other nearby
entries when separated by only 2*PAGE_SIZE, causing a machine check
exception.
Fix this by restoring the old CP0_PageMask value (which should be set to
the normal page size) after reading the TLB entry if we're going to go
ahead and invalidate it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Calculate the PFN of the commpage using virt_to_phys() instead of
CPHYSADDR(). This is more portable as kzalloc() may allocate from XKPhys
instead of KSeg0 on 64-bit kernels, which CPHYSADDR() doesn't handle.
This is sufficient for highmem kernels too since kzalloc() will allocate
from lowmem in KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM TLB mappings for the guest were being created with a cache coherency
attribute (CCA) of 3, which is cached incoherent. Create them instead
with the default host CCA, which should be the correct one for coherency
on SMP systems.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The comm page which is mapped into the guest kernel address space at
0x0 has the unfortunate side effect of allowing guest kernel NULL
pointer dereferences to succeed. The only constraint on this address is
that it must be within 32KiB of 0x0, so that single lw/sw instructions
(which have 16-bit signed offset fields) can be used to access it, using
the zero register as a base.
So lets move the comm page as high as possible within that constraint so
that 0x0 can be left unmapped, at least for page sizes < 32KiB.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Convert KVM to use the MIPS_ENTRYLO_* definitions from <asm/mipsregs.h>
rather than custom definitions in kvm_host.h
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The values of the EntryLo0 and EntryLo1 registers for a TLB entry are
stored in separate members of struct kvm_mips_tlb called tlb_lo0 and
tlb_lo1 respectively. To allow future code which needs to manipulate
arbitrary EntryLo data in the TLB entry to be simpler and less
conditional, replace these members with an array of two elements.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM implements its own routine for dumping the host TLB entries, but we
already have dump_tlb_all() which does something very similar (although
it only prints out TLB entries which match the current ASID or are
global).
Make KVM use dump_tlb_all() along with dump_tlb_regs() to avoid the
duplication and inevitable bitrot, allowing TLB dumping enhancements
(e.g. for VZ and GuestIDs) to be made in a single place.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM's host TLB handling routines were using tlbw hazard barrier macros
around tlb_read(). Now that hazard barrier macros exist for tlbr, update
this case to use them.
Also fix various other unnecessary hazard barriers in this code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Several KVM module functions are indirected so that they can be accessed
from tlb.c which is statically built into the kernel. This is no longer
necessary as the relevant bits of code have moved into mmu.c which is
part of the KVM module, so drop the indirections.
Note: is_error_pfn() is defined inline in kvm_host.h, so didn't actually
require the KVM module to be loaded for it to work anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Various functions in tlb.c perform higher level MMU handling, but don't
strictly need to be statically built into the kernel as they don't
directly manipulate TLB entries. Move these functions out into a
separate mmu.c which will be built into the KVM kernel module. This
allows them to directly reference KVM functions in the KVM kernel module
in future.
Module exports of these functions have been removed, since they aren't
needed outside of KVM.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Convert the MIPS KVM C code to use standard kernel sized types (e.g.
u32) instead of inttypes.h style ones (e.g. uint32_t) or other types as
appropriate.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Convert the MIPS kvm_host.h structs, function declaration prototypes and
associated definition prototypes to use standard kernel sized types
(e.g. u32) instead of inttypes.h style ones (e.g. uint32_t).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
|
|
In preparation for supporting variable ASID masks, retrieve ASID masks
using functions in asm/cpu-info.h which accept struct cpuinfo_mips. This
will allow those functions to determine the ASID mask based upon the CPU
in a later patch. This also allows for the r3k & r8k cases to be handled
in Kconfig, which is arguably cleaner than the previous #ifdefs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In preparation for supporting varied widths of ASID mask in the kernel
in general, switch KVM's guest ASIDs to a new KVM_ENTRYHI_ASID
definition based on the 8-bit MIPS_ENTRYHI_ASID instead of ASID_MASK.
It could potentially be used to support extended guest ASIDs in the
future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13207/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There are a couple of places in KVM fault handling code which implicitly
use smp_processor_id() via kvm_mips_get_kernel_asid() and
kvm_mips_get_user_asid() from preemptable context. This is unsafe as a
preemption could cause the guest kernel ASID to be changed, resulting in
a host TLB entry being written with the wrong ASID.
Fix by disabling preemption around the kvm_mips_get_*_asid() call and
the corresponding kvm_mips_host_tlb_write().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12617/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
|
|
Export symbols only to GPL modules to match other KVM symbols in
virt/kvm/ and arch/*/kvm/.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The function kvm_mips_host_tlb_inv_index() is unused, so drop it
completely.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A bunch of misc whitespace and style fixes within arch/mips/kvm/.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To date, we have implemented two I/O usage models for persistent memory,
PMEM (a persistent "ram disk") and DAX (mmap persistent memory into
userspace). This series adds a third, DAX-GUP, that allows DAX mappings
to be the target of direct-i/o. It allows userspace to coordinate
DMA/RDMA from/to persistent memory.
The implementation leverages the ZONE_DEVICE mm-zone that went into
4.3-rc1 (also discussed at kernel summit) to flag pages that are owned
and dynamically mapped by a device driver. The pmem driver, after
mapping a persistent memory range into the system memmap via
devm_memremap_pages(), arranges for DAX to distinguish pfn-only versus
page-backed pmem-pfns via flags in the new pfn_t type.
The DAX code, upon seeing a PFN_DEV+PFN_MAP flagged pfn, flags the
resulting pte(s) inserted into the process page tables with a new
_PAGE_DEVMAP flag. Later, when get_user_pages() is walking ptes it keys
off _PAGE_DEVMAP to pin the device hosting the page range active.
Finally, get_page() and put_page() are modified to take references
against the device driver established page mapping.
Finally, this need for "struct page" for persistent memory requires
memory capacity to store the memmap array. Given the memmap array for a
large pool of persistent may exhaust available DRAM introduce a
mechanism to allocate the memmap from persistent memory. The new
"struct vmem_altmap *" parameter to devm_memremap_pages() enables
arch_add_memory() to use reserved pmem capacity rather than the page
allocator.
This patch (of 18):
The core has developed a need for a "pfn_t" type [1]. Move the existing
pfn_t in KVM to kvm_pfn_t [2].
[1]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002199.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002218.html
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a vcpu_get_regs() and vcpu_set_regs() callbacks for loading and
restoring context which may be in hardware registers. This may include
floating point and MIPS SIMD Architecture (MSA) state which may be
accessed directly by the guest (but restored lazily by the hypervisor),
and also dedicated guest registers as provided by the VZ ASE.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Enable disabled interrupt, on unsuccessful operation.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Since all the files are in arch/mips/kvm/, there's no need of the prefixes
"kvm_" and "kvm_mips_".
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
