summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2021-10-26Merge tag 'arm-soc-fixes-5.15-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "One last set of small fixes for the soc tree: - Incorrect ethernet phy settings found on i.mx and allwinner platforms - a revert for a Qualcomm DT change that caused a boot regression - four patches for incorrect settings in i.MX DT files - new MAINTAINER file entries for dhcom boards - a Kconfig fix for a reset driver that became unselectable - three more code changes for bugs in reset drivers" * tag 'arm-soc-fixes-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: MAINTAINERS: Add maintainers for DHCOM i.MX6 and DHCOM/DHCOR STM32MP1 Revert "arm64: dts: qcom: sm8250: remove bus clock from the mdss node for sm8250 target" arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency arm64: dts: imx8mm-kontron: Fix polarity of reg_rst_eth2 arm64: dts: imx8mm-kontron: Set lower limit of VDD_SNVS to 800 mV arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct reset: socfpga: add empty driver allowing consumers to probe reset: tegra-bpmp: Handle errors in BPMP response reset: pistachio: Re-enable driver selection reset: brcmstb-rescal: fix incorrect polarity of status bit ARM: dts: sun7i: A20-olinuxino-lime2: Fix ethernet phy-mode arm64: dts: allwinner: h5: NanoPI Neo 2: Fix ethernet node
2021-10-25Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: - Fix clang-related relocation warning in futex code - Fix incorrect use of get_kernel_nofault() - Fix bad code generation in __get_user_check() when kasan is enabled - Ensure TLB function table is correctly aligned - Remove duplicated string function definitions in decompressor - Fix link-time orphan section warnings - Fix old-style function prototype for arch_init_kprobes() - Only warn about XIP address when not compile testing - Handle BE32 big endian for keystone2 remapping * tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 9148/1: handle CONFIG_CPU_ENDIAN_BE32 in arch/arm/kernel/head.S ARM: 9141/1: only warn about XIP address when not compile testing ARM: 9139/1: kprobes: fix arch_init_kprobes() prototype ARM: 9138/1: fix link warning with XIP + frame-pointer ARM: 9134/1: remove duplicate memcpy() definition ARM: 9133/1: mm: proc-macros: ensure *_tlb_fns are 4B aligned ARM: 9132/1: Fix __get_user_check failure with ARM KASAN images ARM: 9125/1: fix incorrect use of get_kernel_nofault() ARM: 9122/1: select HAVE_FUTEX_CMPXCHG
2021-10-25ARM: 9148/1: handle CONFIG_CPU_ENDIAN_BE32 in arch/arm/kernel/head.SLABBE Corentin
My intel-ixp42x-welltech-epbx100 no longer boot since 4.14. This is due to commit 463dbba4d189 ("ARM: 9104/2: Fix Keystone 2 kernel mapping regression") which forgot to handle CONFIG_CPU_ENDIAN_BE32 as possible BE config. Suggested-by: Krzysztof Hałasa <khalasa@piap.pl> Fixes: 463dbba4d189 ("ARM: 9104/2: Fix Keystone 2 kernel mapping regression") Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-20Merge tag 'sunxi-fixes-for-5.15-1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes Two patches to fix the GMAC PHY mode on some boards. * tag 'sunxi-fixes-for-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sun7i: A20-olinuxino-lime2: Fix ethernet phy-mode arm64: dts: allwinner: h5: NanoPI Neo 2: Fix ethernet node Link: https://lore.kernel.org/r/d4c41c71-f1ff-4464-a26f-1bfd4b52fd78.lettre@localhost Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-19ARM: 9141/1: only warn about XIP address when not compile testingArnd Bergmann
In randconfig builds, we sometimes come across this warning: arm-linux-gnueabi-ld: XIP start address may cause MPU programming issues While this is helpful for actual systems to figure out why it fails, the warning does not provide any benefit for build testing, so guard it in a check for CONFIG_COMPILE_TEST, which is usually set on randconfig builds. Fixes: 216218308cfb ("ARM: 8713/1: NOMMU: Support MPU in XIP configuration") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9139/1: kprobes: fix arch_init_kprobes() prototypeArnd Bergmann
With extra warnings enabled, gcc complains about this function definition: arch/arm/probes/kprobes/core.c: In function 'arch_init_kprobes': arch/arm/probes/kprobes/core.c:465:12: warning: old-style function definition [-Wold-style-definition] 465 | int __init arch_init_kprobes() Link: https://lore.kernel.org/all/20201027093057.c685a14b386acacb3c449e3d@kernel.org/ Fixes: 24ba613c9d6c ("ARM kprobes: core code") Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9138/1: fix link warning with XIP + frame-pointerArnd Bergmann
When frame pointers are used instead of the ARM unwinder, and the kernel is built using clang with an external assembler and CONFIG_XIP_KERNEL, every file produces two warnings like: arm-linux-gnueabi-ld: warning: orphan section `.ARM.extab' from `net/mac802154/util.o' being placed in section `.ARM.extab' arm-linux-gnueabi-ld: warning: orphan section `.ARM.exidx' from `net/mac802154/util.o' being placed in section `.ARM.exidx' The same fix was already merged for the normal (non-XIP) linker script, with a longer description. Fixes: c39866f268f8 ("arm/build: Always handle .ARM.exidx and .ARM.extab sections") Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9134/1: remove duplicate memcpy() definitionArnd Bergmann
Both the decompressor code and the kasan logic try to override the memcpy() and memmove() definitions, which leading to a clash in a KASAN-enabled kernel with XZ decompression: arch/arm/boot/compressed/decompress.c:50:9: error: 'memmove' macro redefined [-Werror,-Wmacro-redefined] #define memmove memmove ^ arch/arm/include/asm/string.h:59:9: note: previous definition is here #define memmove(dst, src, len) __memmove(dst, src, len) ^ arch/arm/boot/compressed/decompress.c:51:9: error: 'memcpy' macro redefined [-Werror,-Wmacro-redefined] #define memcpy memcpy ^ arch/arm/include/asm/string.h:58:9: note: previous definition is here #define memcpy(dst, src, len) __memcpy(dst, src, len) ^ Here we want the set of functions from the decompressor, so undefine the other macros before the override. Link: https://lore.kernel.org/linux-arm-kernel/CACRpkdZYJogU_SN3H9oeVq=zJkRgRT1gDz3xp59gdqWXxw-B=w@mail.gmail.com/ Link: https://lore.kernel.org/lkml/202105091112.F5rmd4By-lkp@intel.com/ Fixes: d6d51a96c7d6 ("ARM: 9014/2: Replace string mem* functions for KASan") Fixes: a7f464f3db93 ("ARM: 7001/2: Wire up support for the XZ decompressor") Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9133/1: mm: proc-macros: ensure *_tlb_fns are 4B alignedNick Desaulniers
A kernel built with CONFIG_THUMB2_KERNEL=y and using clang as the assembler could generate non-naturally-aligned v7wbi_tlb_fns which results in a boot failure. The original commit adding the macro missed the .align directive on this data. Link: https://github.com/ClangBuiltLinux/linux/issues/1447 Link: https://lore.kernel.org/all/0699da7b-354f-aecc-a62f-e25693209af4@linaro.org/ Debugged-by: Ard Biesheuvel <ardb@kernel.org> Debugged-by: Nathan Chancellor <nathan@kernel.org> Debugged-by: Richard Henderson <richard.henderson@linaro.org> Fixes: 66a625a88174 ("ARM: mm: proc-macros: Add generic proc/cache/tlb struct definition macros") Suggested-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9132/1: Fix __get_user_check failure with ARM KASAN imagesLexi Shao
ARM: kasan: Fix __get_user_check failure with kasan In macro __get_user_check defined in arch/arm/include/asm/uaccess.h, error code is store in register int __e(r0). When kasan is enabled, assigning value to kernel address might trigger kasan check, which unexpectedly overwrites r0 and causes undefined behavior on arm kasan images. One example is failure in do_futex and results in process soft lockup. Log: watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main Q:Reg:1151] ... (__asan_store4) from (futex_wait_setup+0xf8/0x2b4) (futex_wait_setup) from (futex_wait+0x138/0x394) (futex_wait) from (do_futex+0x164/0xe40) (do_futex) from (sys_futex_time32+0x178/0x230) (sys_futex_time32) from (ret_fast_syscall+0x0/0x50) The soft lockup happens in function futex_wait_setup. The reason is function get_futex_value_locked always return EINVAL, thus pc jump back to retry label and causes looping. This line in function get_futex_value_locked ret = __get_user(*dest, from); is expanded to *dest = (typeof(*(p))) __r2; , in macro __get_user_check. Writing to pointer dest triggers kasan check and overwrites the return value of __get_user_x function. The assembly code of get_futex_value_locked in kernel/futex.c: ... c01f6dc8: eb0b020e bl c04b7608 <__get_user_4> // "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten c01f6dCc: e1a00007 mov r0, r7 c01f6dd0: e1a05002 mov r5, r2 c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4> c01f6dd8: e5875000 str r5, [r7] // save ret value of __get_user(*dest, from), which is dest address now c01f6ddc: e1a05000 mov r5, r0 ... // checking return value of __get_user failed c01f6e00: e3550000 cmp r5, #0 ... c01f6e0c: 01a00005 moveq r0, r5 // assign return value to EINVAL c01f6e10: 13e0000d mvnne r0, #13 Return value is the destination address of get_user thus certainly non-zero, so get_futex_value_locked always return EINVAL. Fix it by using a tmp vairable to store the error code before the assignment. This fix has no effects to non-kasan images thanks to compiler optimization. It only affects cases that overwrite r0 due to kasan check. This should fix bug discussed in Link: [1] https://lore.kernel.org/linux-arm-kernel/0ef7c2a5-5d8b-c5e0-63fa-31693fd4495c@gmail.com/ Fixes: 421015713b30 ("ARM: 9017/2: Enable KASan for ARM") Signed-off-by: Lexi Shao <shaolexi@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9125/1: fix incorrect use of get_kernel_nofault()Ard Biesheuvel
Commit 344179fc7ef4 ("ARM: 9106/1: traps: use get_kernel_nofault instead of set_fs()") replaced an occurrence of __get_user() with get_kernel_nofault(), but inverted the sense of the conditional in the process, resulting in no values to be printed at all. I.e., every exception stack now looks like this: Exception stack(0xc18d1fb0 to 0xc18d1ff8) 1fa0: ???????? ???????? ???????? ???????? 1fc0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? 1fe0: ???????? ???????? ???????? ???????? ???????? ???????? which is rather unhelpful. Fixes: 344179fc7ef4 ("ARM: 9106/1: traps: use get_kernel_nofault instead of set_fs()") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-19ARM: 9122/1: select HAVE_FUTEX_CMPXCHGNick Desaulniers
tglx notes: This function [futex_detect_cmpxchg] is only needed when an architecture has to runtime discover whether the CPU supports it or not. ARM has unconditional support for this, so the obvious thing to do is the below. Fixes linkage failure from Clang randconfigs: kernel/futex.o:(.text.fixup+0x5c): relocation truncated to fit: R_ARM_JUMP24 against `.init.text' and boot failures for CONFIG_THUMB2_KERNEL. Link: https://github.com/ClangBuiltLinux/linux/issues/325 Comments from Nick Desaulniers: See-also: 03b8c7b623c8 ("futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test") Reported-by: Arnd Bergmann <arnd@arndb.de> Reported-by: Nathan Chancellor <nathan@kernel.org> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org # v3.14+ Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
2021-10-17Merge tag 'driver-core-5.15-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fixes from Greg KH: "Here are some small driver core fixes for 5.15-rc6, all of which have been in linux-next for a while with no reported issues. They include: - kernfs negative dentry bugfix - simple pm bus fixes to resolve reported issues" * tag 'driver-core-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: drivers: bus: Delete CONFIG_SIMPLE_PM_BUS drivers: bus: simple-pm-bus: Add support for probing simple bus only devices driver core: Reject pointless SYNC_STATE_ONLY device links kernfs: don't create a negative dentry if inactive node exists
2021-10-16Merge tag 'arm-soc-fixes-5.15-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "A small number fixes this time, mostly touching actual code: - Add platform device for i.MX System Reset Controller (SRC) to fix a regression caused by fw_devlink change - A fixup for a boot regression caused by my own rework for the Qualcomm SCM driver - Multiple bugfixes for the Arm FFA and optee firmware drivers, addressing problems when they are built as a loadable module - Four dts bugfixes for the Broadcom SoC used in Raspberry pi, addressing VEC (video encoder), MDIO bus controller #address-cells/#size-cells, SDIO voltage and PCIe host bridge dtc warnings" * tag 'arm-soc-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: imx: register reset controller from a platform driver iommu/arm: fix ARM_SMMU_QCOM compilation ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting tee: optee: Fix missing devices unregister during optee_remove ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states ARM: dts: bcm2711: fix MDIO #address- and #size-cells ARM: dts: bcm283x: Fix VEC address for BCM2711 firmware: arm_ffa: Fix __ffa_devices_unregister firmware: arm_ffa: Add missing remove callback to ffa_bus_type
2021-10-15Merge tag 'imx-fixes-5.15-3' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.15, round 3: - Add platform device for i.MX System Reset Controller (SRC) to fix a regression caused by fw_devlink change. * tag 'imx-fixes-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: imx: register reset controller from a platform driver Link: https://lore.kernel.org/r/20211015070017.GI22881@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-15ARM: imx: register reset controller from a platform driverPhilipp Zabel
Starting with commit 6b2117ad65f1 ("of: property: fw_devlink: Add support for "resets" and "pwms""), the imx-drm driver fails to load due to forever dormant devlinks to the reset-controller node. This node was never associated with a struct device. Add a platform device to allow fw_devnode to activate the devlinks. Fixes: 6b2117ad65f1 ("of: property: fw_devlink: Add support for "resets" and "pwms"") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-10-14Merge tag 'net-5.15-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Quite calm. The noisy DSA driver (embedded switches) changes, and adjustment to IPv6 IOAM behavior add to diffstat's bottom line but are not scary. Current release - regressions: - af_unix: rename UNIX-DGRAM to UNIX to maintain backwards compatibility - procfs: revert "add seq_puts() statement for dev_mcast", minor format change broke user space Current release - new code bugs: - dsa: fix bridge_num not getting cleared after ports leaving the bridge, resource leak - dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware bridges using VID 0, prevent packet drops if pvid is removed - dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW getting confused about station to VLAN mapping Previous releases - regressions: - virtio-net: fix for skb_over_panic inside big mode - phy: do not shutdown PHYs in READY state - dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link LED staying lit after ifdown - mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL) - mqprio: Correct stats in mqprio_dump_class_stats() - ice: fix deadlock for Tx timestamp tracking flush - stmmac: fix feature detection on old hardware Previous releases - always broken: - sctp: account stream padding length for reconf chunk - icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe() - isdn: cpai: check ctr->cnr to avoid array index out of bound - isdn: mISDN: fix sleeping function called from invalid context - nfc: nci: fix potential UAF of rf_conn_info object - dsa: microchip: prevent ksz_mib_read_work from kicking back in after it's canceled in .remove and crashing - dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged ports - dsa: sja1105, ocelot: break circular dependency between switch and tag drivers - dsa: felix: improve timestamping in presence of packe loss - mlxsw: thermal: fix out-of-bounds memory accesses Misc: - ipv6: ioam: move the check for undefined bits to improve interoperability" * tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits) icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe MAINTAINERS: Update the devicetree documentation path of imx fec driver sctp: account stream padding length for reconf chunk mlxsw: thermal: Fix out-of-bounds memory accesses ethernet: s2io: fix setting mac address during resume NFC: digital: fix possible memory leak in digital_in_send_sdd_req() NFC: digital: fix possible memory leak in digital_tg_listen_mdaa() nfc: fix error handling of nfc_proto_register() Revert "net: procfs: add seq_puts() statement for dev_mcast" net: encx24j600: check error in devm_regmap_init_encx24j600 net: korina: select CRC32 net: arc: select CRC32 net: dsa: felix: break at first CPU port during init and teardown net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header net: mscc: ocelot: deny TX timestamping of non-PTP packets net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb ...
2021-10-13Merge tag 'arm-soc/for-5.15/devicetree' of ↵Arnd Bergmann
https://github.com/Broadcom/stblinux into arm/fixes This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 5.15, please pull the following: - Stefan fixes the VEC (video encoder) bus address for 2711, fixes the MDIO bus controller #address-cells/#size-cells inversion and the SDIO regulator voltage ranges - Nicolas fixes DTC warnings for the PCIe host bridge and its child USB device * tag 'arm-soc/for-5.15/devicetree' of https://github.com/Broadcom/stblinux: ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states ARM: dts: bcm2711: fix MDIO #address- and #size-cells ARM: dts: bcm283x: Fix VEC address for BCM2711 Link: https://lore.kernel.org/r/20211012213841.1872021-1-f.fainelli@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-12ARM: dts: bcm2711-rpi-4-b: Fix usb's unit addressNicolas Saenz Julienne
The unit address is supposed to represent '<device>,<function>'. Which are both 0 for RPi4b's XHCI controller. On top of that although OpenFirmware states bus number goes in the high part of the last reg parameter, FDT doesn't seem to care for it[1], so remove it. [1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210830103909.323356-1-nsaenzju@redhat.com/#24414633 Fixes: 258f92d2f840 ("ARM: dts: bcm2711: Add reset controller to xHCI node") Suggested-by: Rob Herring <robh@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210831125843.1233488-2-nsaenzju@redhat.com Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
2021-10-12ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formattingNicolas Saenz Julienne
dtbs_check currently complains that: arch/arm/boot/dts/bcm2711-rpi-4-b.dts:220.10-231.4: Warning (pci_device_reg): /scb/pcie@7d500000/pci@1,0: PCI unit address format error, expected "0,0" Unsurprisingly pci@0,0 is the right address, as illustrated by its reg property: &pcie0 { pci@0,0 { /* * As defined in the IEEE Std 1275-1994 document, * reg is a five-cell address encoded as (phys.hi * phys.mid phys.lo size.hi size.lo). phys.hi * should contain the device's BDF as 0b00000000 * bbbbbbbb dddddfff 00000000. The other cells * should be zero. */ reg = <0 0 0 0 0>; }; }; The device is clearly 0. So fix it. Also add a missing 'device_type = "pci"'. Fixes: 258f92d2f840 ("ARM: dts: bcm2711: Add reset controller to xHCI node") Suggested-by: Rob Herring <robh@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210831125843.1233488-1-nsaenzju@redhat.com Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
2021-10-08Merge tag 'asm-generic-fixes-5.15' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic Pull asm-generic fixes from Arnd Bergmann: "There is one build fix for Arm platforms that ended up impacting most architectures because of the way the drivers/firmware Kconfig file is wired up: The CONFIG_QCOM_SCM dependency have caused a number of randconfig regressions over time, and some still remain in v5.15-rc4. The fix we agreed on in the end is to make this symbol selected by any driver using it, and then building it even for non-Arm platforms with CONFIG_COMPILE_TEST. To make this work on all architectures, the drivers/firmware/Kconfig file needs to be included for all architectures to make the symbol itself visible. In a separate discussion, we found that a sound driver patch that is pending for v5.16 needs the same change to include this Kconfig file, so the easiest solution seems to have my Kconfig rework included in v5.15. Finally, the branch also includes a small unrelated build fix for NOMMU architectures" Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/ Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/ Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/ * tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere qcom_scm: hide Kconfig symbol firmware: include drivers/firmware/Kconfig unconditionally
2021-10-08ARM: dts: spear3xx: Fix gmac nodeHerve Codina
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600 one. Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and needs some driver tuning compare to SPEAr600. The v3.40 IP support was added to stmmac driver and this patch fixes this issue and use the correct compatible string for SPEAr3xx Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-07Merge tag 'armsoc-fixes-5.15' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "This is a larger than normal update for Arm SoC specific code, most of it in device trees, but also drivers and the omap and at91/sama7 platforms: - There are four new entries to the MAINTAINERS file: Sven Peter and Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar, and Vignesh Raghavendra for TI K3 - Build fixes to address randconfig warnings in sharpsl, dove, omap1, and qcom platforms as well as the scmi and op-tee subsystems - Regression fixes for missing CONFIG_FB and other options for several defconfigs - Several bug fixes for the newly added Microchip SAMA7 platform, mostly regarding power management - Missing SMP barriers to protect accesses to SCMI virtio device - Regression fixes for TI OMAP, including a boot-time hang on am335x. - Lots of bug fixes for NXP i.MX, mostly addressing incorrect settings in devicetree files, and one revert for broken suspend. - Fixes for ARM Juno/Vexpress devicetree files, addressing a couple of schema warnings. - Regression fixes for qualcomm SoC specific drivers and devicetree files, reverting an mdt_loader change and at least pastially reverting some of the 5.15 DTS changes, plus some minor bugfixes" * tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits) MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer firmware: arm_scmi: Add proper barriers to scmi virtio device firmware: arm_scmi: Simplify spinlocks in virtio transport ARM: dts: omap3430-sdp: Fix NAND device node bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893 ARM: sharpsl_param: work around -Wstringop-overread warning ARM: defconfig: gemini: Restore framebuffer ARM: dove: mark 'putc' as inline ARM: omap1: move omap15xx local bus handling to usb.c MAINTAINERS: Add Vignesh to TI K3 platform maintainership arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence arm64: dts: ls1028a: fix eSDHC2 node arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2 ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs ARM: at91: pm: preload base address of controllers in tlb ARM: at91: pm: group constants and addresses loading ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail ...
2021-10-07Merge tag 'omap-for-v5.15/fixes-rc4' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omaps for v5.15 Few regression fixes for omaps for the v5.15-rc cycle. There is a fix for boot time hangs that can happen on some am335x devices that started when the pruss devicetree nodes were added. The other fixes are less critical: - Fix compiler warning for sysc_init_soc() that got recently introduced - Fix external abort for am335x pruss as otherwise some am335x will hang - Use CLKDM_NOAUTO quirk also for dra7 dcan1 - Fix older NAND device node regression for omap3-sdp * tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: omap3430-sdp: Fix NAND device node bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893 soc: ti: omap-prm: Fix external abort for am335x pruss bus: ti-sysc: Add break in switch statement in sysc_init_soc() Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-07firmware: include drivers/firmware/Kconfig unconditionallyArnd Bergmann
Compile-testing drivers that require access to a firmware layer fails when that firmware symbol is unavailable. This happened twice this week: - My proposed to change to rework the QCOM_SCM firmware symbol broke on ppc64 and others. - The cs_dsp firmware patch added device specific firmware loader into drivers/firmware, which broke on the same set of architectures. We should probably do the same thing for other subsystems as well, but fix this one first as this is a dependency for other patches getting merged. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Will Deacon <will@kernel.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: Simon Trimmer <simont@opensource.cirrus.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-07Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski
Daniel Borkmann says: ==================== pull-request: bpf 2021-10-07 We've added 7 non-merge commits during the last 8 day(s) which contain a total of 8 files changed, 38 insertions(+), 21 deletions(-). The main changes are: 1) Fix ARM BPF JIT to preserve caller-saved regs for DIV/MOD JIT-internal helper call, from Johan Almbladh. 2) Fix integer overflow in BPF stack map element size calculation when used with preallocation, from Tatsuhiko Yasumatsu. 3) Fix an AF_UNIX regression due to added BPF sockmap support related to shutdown handling, from Jiang Wang. 4) Fix a segfault in libbpf when generating light skeletons from objects without BTF, from Kumar Kartikeya Dwivedi. 5) Fix a libbpf memory leak in strset to free the actual struct strset itself, from Andrii Nakryiko. 6) Dual-license bpf_insn.h similarly as we did for libbpf and bpftool, with ACKs from all contributors, from Luca Boccassi. ==================== Link: https://lore.kernel.org/r/20211007135010.21143-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-06Merge tag 'imx-fixes-5.15-2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.15, round 2: - A couple of fixes from Haibo Chen to update SPI NOR TX bus width for i.MX6 and i.MX8 boards. This becomes necessary because spi-nor driver starts using the setting in DT. - Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the core supply being turned off unexpectedly. - Fix eSDHC2 device tree settings for LS1028A SoC. - Disable GIC CPU interface before calling stby-poweroff sequence to fix power-off failure on i.MX6. - Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards. * tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence arm64: dts: ls1028a: fix eSDHC2 node arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2 arm64: dts: imx8: change the spi-nor tx ARM: dts: imx: change the spi-nor tx Link: https://lore.kernel.org/r/20211006125734.GA10197@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-06ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator statesStefan Wahren
DT schema check complains at sd_io_1v8_reg about the following: [1800000, 1, 3300000, 0] is too long Additional items are not allowed (3300000, 0 were unexpected) So fix the states definition. Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/1628334401-6577-3-git-send-email-stefan.wahren@i2se.com Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
2021-10-06ARM: dts: bcm2711: fix MDIO #address- and #size-cellsStefan Wahren
The values of #address-cells and #size-cells are swapped. Fix this and avoid the following DT schema warnings for mdio@e14: #address-cells:0:0: 1 was expected #size-cells:0:0: 0 was expected Fixes: be8af7a9e3cc ("ARM: dts: bcm2711-rpi-4: Enable GENET support") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/1628334401-6577-2-git-send-email-stefan.wahren@i2se.com Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
2021-10-06ARM: dts: bcm283x: Fix VEC address for BCM2711Mateusz Kwiatkowski
The VEC has a different address (0x7ec13000) on the BCM2711 (used in e.g. Raspberry Pi 4) compared to BCM283x (e.g. Pi 3 and earlier). This was erroneously not taken account for. Definition of the VEC in the devicetrees had to be moved from bcm283x.dtsi to bcm2711.dtsi and bcm2835-common.dtsi to allow for this differentiation. Fixes: 7894bdc6228f ("ARM: boot: dts: bcm2711: Add BCM2711 VEC compatible") Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/1626980528-3835-1-git-send-email-stefan.wahren@i2se.com Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
2021-10-06ARM: dts: omap3430-sdp: Fix NAND device nodeRoger Quadros
Nand is on CS1 so reg properties first field should be 1 not 0. Fixes: 44e4716499b8 ("ARM: dts: omap3: Fix NAND device nodes") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-10-06bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893Tony Lindgren
Commit 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in addition to dcan2 for errata i893 handling. Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods" dts property is used with related dcan hwmod data. This should be only needed if anybody needs to git bisect earlier stable trees though. Fixes: 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO") Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-10-05drivers: bus: Delete CONFIG_SIMPLE_PM_BUSSaravana Kannan
The simple-pm-bus driver is mandatory for CONFIG_OF based platforms to work with fw_devlink. So, always compile it in for CONFIG_OF and delete the config since it's no longer necessary. Tested-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Damien Le Moal <damien.lemoal@wdc.com> Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Saravana Kannan <saravanak@google.com> Link: https://lore.kernel.org/r/20210929000735.585237-3-saravanak@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-05ARM: sharpsl_param: work around -Wstringop-overread warningArnd Bergmann
gcc warns that accessing a pointer based on a numeric constant may be an offset into a NULL pointer, and would therefore has zero accessible bytes: arch/arm/common/sharpsl_param.c: In function ‘sharpsl_save_param’: arch/arm/common/sharpsl_param.c:43:9: error: ‘memcpy’ reading 64 bytes from a region of size 0 [-Werror=stringop-overread] 43 | memcpy(&sharpsl_param, param_start(PARAM_BASE), sizeof(struct sharpsl_param_info)); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ In this particular case, the warning is bogus since this is the actual pointer, not an offset on a NULL pointer. Add a local variable to shut up the warning and hope it doesn't come back. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Daniel Mack <daniel@zonque.org> Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Russell King <linux@armlinux.org.uk> Cc: Linus Walleij <linus.walleij@linaro.org> Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578 Link: https://lore.kernel.org/r/20210927145332.2784005-1-arnd@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05Merge tag 'imx-fixes-5.15' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.15: - Revert cc8870bf4c3a to fix the regression on i.MX6 that suspend support becomes broken. - Add `qca,clk-out-frequency` property to fix Ethernet support on imx6qdl-pico board. - Re-enable FB support in imx_v6_v7_defconfig. It gets lost due to f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB"). - Fix LP5562 LED support on imx6dl-yapp4 board. - Add missing pinctrl-names for panel on M53Menlo board. - Fix USB host power regulator polarity on M53Menlo board. * tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: imx_v6_v7_defconfig: enable fb ARM: dts: imx6qdl-pico: Fix Ethernet support ARM: dts: imx: Fix USB host power regulator polarity on M53Menlo ARM: dts: imx: Add missing pinctrl-names for panel on M53Menlo Revert "ARM: imx6q: drop of_platform_default_populate() from init_machine" ARM: dts: imx6dl-yapp4: Fix lp5562 LED driver probe Link: https://lore.kernel.org/r/20210923063356.GK13480@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05ARM: defconfig: gemini: Restore framebufferLinus Walleij
The framebuffer is gone on the D-Link DIR-685, restore it. Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20210922200933.1825752-1-linus.walleij@linaro.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05ARM: dove: mark 'putc' as inlineArnd Bergmann
This can cause a randconfig warning without the 'inline' flag that every other platform uses: In file included from arch/arm/boot/compressed/misc.c:29: arch/arm/mach-dove/include/mach/uncompress.h:14:13: error: 'putc' defined but not used [-Werror=unused-function] 14 | static void putc(const char c) | ^~~~ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210927095343.1015422-1-arnd@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05ARM: omap1: move omap15xx local bus handling to usb.cArnd Bergmann
Commit 38225f2ef2f4 ("ARM/omap1: switch to use dma_direct_set_offset for lbus DMA offsets") removed a lot of mach/memory.h, but left the USB offset handling split into arch/arm/mach-omap1/usb.c and drivers/usb/host/ohci-omap.c. This can cause a randconfig build warning that now fails the build with -Werror: arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable] 561 | static struct notifier_block omap_1510_usb_ohci_nb = { | ^~~~~~~~~~~~~~~~~~~~~ Move it all into the platform file to get rid of the final location that relies on mach/memory.h. Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05Merge tag 'juno-fixes-5.15' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes Juno/Vexpress fixes for v5.15 Bunch of DTS fixes to resolve addressing issues with some of the device nodes, dropping unused/undocumented properties in various nodes, and aligning node names with dtschema. * tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: arm: dts: vexpress: Fix motherboard bus 'interrupt-map' arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes arm: dts: vexpress-v2p-ca9: Fix the SMB unit-address arm: dts: vexpress: Drop unused properties from motherboard node arm64: dts: arm: drop unused interrupt-names in MHU ARM: dts: arm: align watchdog and mmc node names with dtschema arm64: dts: arm: align watchdog and mmc node names with dtschema arm64: dts: fvp: Remove panel timings Link: https://lore.kernel.org/r/20210927105249.3583380-1-sudeep.holla@arm.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05Merge tag 'qcom-dts-fixes-for-5.15' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes Qualcomm DTS fixes for v5.15 This corrects the use of depricated chipid and clock names, for which support was finally dropped from the driver. It also ensures that the DSI PLL is fed by the correct clock, now that it's being migrated to not rely on global clock names. * tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: ARM: dts: qcom: apq8064: update Adreno clock names ARM: dts: qcom: apq8064: Use 27MHz PXO clock as DSI PLL reference ARM: dts: qcom: apq8064: use compatible which contains chipid Link: https://lore.kernel.org/r/20210930025526.1146-1-bjorn.andersson@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05Merge tag 'at91-fixes-5.15-2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes AT91 fixes #2 for 5.15: - More fixes for AT91 platform power management code related to the introduction of sama7g5: - management of DDR3L regulator rails for sama7g5ek - loading of TLB on different cores - PIO controller slew-rate settings for sama7g5ek: be aligned with datasheet requirements. * tag 'at91-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs ARM: at91: pm: preload base address of controllers in tlb ARM: at91: pm: group constants and addresses loading ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail Link: https://lore.kernel.org/r/20211004114344.19304-1-nicolas.ferre@microchip.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-05ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequenceOleksij Rempel
Any pending interrupt can prevent entering standby based power off state. To avoid it, disable the GIC CPU interface. Fixes: 8148d2136002 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-10-04ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pinsClaudiu Beznea
With commit c709135e576b ("pinctrl: at91-pio4: add support for slew-rate") and commit cbde6c823bfa ("pinctrl: at91-pio4: Fix slew rate disablement") the slew-rate is enabled by default for each configured pin. The datasheet specifies at chapter "Output Driver AC Characteristics" that HSIO drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate setting but are rather calibrated against an external 1% resistor mounted on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal frequency and the external load, it is possible to adjust their target output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled at the moment in device tree). Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
2021-10-04ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACsClaudiu Beznea
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain GMAC's MDIO pins should be configured with slew-rate enabled, while the data + signaling pins should be configured with slew-rate disabled when GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets the slew-rate as enabled for all pins. Adapt the device tree to comply with these. Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com
2021-10-04ARM: at91: pm: preload base address of controllers in tlbClaudiu Beznea
In suspend/resume procedure for AT91 architecture different controllers (PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings for power saving. Commit f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5") introduced the access to RAMC PHY controller for SAMA7G5. The access to this controller is done after RAMC ports are closed, thus any TLB walk necessary for RAMC PHY virtual address will fail. In the development branch this was not encountered. However, on current kernel the issue is reproducible. To solve the issue the previous mechanism of pre-loading the TLB with the RAMC PHY virtual address has been used. However, only the addition of this new pre-load breaks the functionality for ARMv5 based devices (SAM9X60). This behavior has been encountered previously while debugging this code and using the same mechanism for pre-loading address for different controllers (e.g. pin controller, the assumption being that other requested translations are replaced from TLB). To solve this new issue the TLB flush + the extension of pre-loading the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The rest of the controllers should have been pre-loaded previously, anyway. Fixes: f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5") Depends-on: e42cbbe5c9a2 ("ARM: at91: pm: group constants and addresses loading") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210930154219.2214051-4-claudiu.beznea@microchip.com
2021-10-04ARM: at91: pm: group constants and addresses loadingClaudiu Beznea
Group constants and addresses loading. This commit prepares the field for the next one. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210930154219.2214051-3-claudiu.beznea@microchip.com
2021-10-04ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l railClaudiu Beznea
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The 1.35V for DDR3L rail at run-time is selected by the proper configuration on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of configuration registers to provide proper voltages on its rail. Run-time configuration registers could be configured differently than suspend configuration register for MCP16502 (VSEL2 affects only run-time configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK switches to self-refresh. Even on self-refresh it needs to be powered by a 1.35V rail. Thus, make sure the PMIC is configured properly when system is suspended. Fixes: 7540629e2fc7 (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
2021-10-04ARM: dts: imx: change the spi-nor txHaibo Chen
Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"), for all PP command, it only support 1-1-1 mode, no matter the tx setting in dts. But after the upper commit, the logic change. It will choose the best mode(fastest mode) which flash device and spi-nor host controller both support. Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also impact the read mode selection. For the spi-nor device on the upper mentioned boards, they support read 1-4-4 mode and read 1-1-4 mode according to the device internal sfdp register. But qspi host controller do not support read 1-4-4 mode. so need to set the tx to 1, let the common code finally select read 1-1-4 mode, PP-1-1-1 mode. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol") Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-09-29bpf, arm: Fix register clobbering in div/mod implementationJohan Almbladh
On ARM CPUs that lack div/mod instructions, ALU32 BPF_DIV and BPF_MOD are implemented using a call to a helper function. Before, the emitted code for those function calls failed to preserve caller-saved ARM registers. Since some of those registers happen to be mapped to BPF registers, it resulted in eBPF register values being overwritten. This patch emits code to push and pop the remaining caller-saved ARM registers r2-r3 into the stack during the div/mod function call. ARM registers r0-r1 are used as arguments and return value, and those were already saved and restored correctly. Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler") Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2021-09-26arm: dts: vexpress: Fix motherboard bus 'interrupt-map'Rob Herring
Commit 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes") broke booting on a couple of 32-bit VExpress boards. The problem is #address-cells size changed, but interrupt-map was not updated. This results in the timer interrupt (and all the other motherboard interrupts) not getting mapped. As the 'interrupt-map' properties are all just duplicates across boards, just move them into vexpress-v2m.dtsi and vexpress-v2m-rs1.dtsi. Strictly speaking, 'interrupt-map' is dependent on the parent interrupt controller, but it's not likely we'll ever have a different parent than GICv2 on these old platforms. If there was one, 'interrupt-map' can still be overridden. Link: https://lore.kernel.org/r/20210924214221.1877686-1-robh@kernel.org Fixes: 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes") Cc: Guillaume Tucker <guillaume.tucker@collabora.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: linux-arm-kernel@lists.infradead.org Reported-by: Reported-by: "kernelci.org bot" <bot@kernelci.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
generated by cgit v1.2.3-58-ga151 (git 2.39.0) at 2024-12-19 00:10:35 +0000