| Age | Commit message (Collapse) | Author |
|---|
|
The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.
Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
|
|
SOF_TIMESTAMPING_OPT_ID puts the id in ee_data, not ee_info.
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Assorted fixes, most in overlayfs land"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: ovl_dir_fsync() cleanup
ovl: update MAINTAINERS
ovl: pass dentry into ovl_dir_read_merged()
ovl: use lockless_dereference() for upperdentry
ovl: allow filenames with comma
ovl: fix race in private xattr checks
ovl: fix remove/copy-up race
ovl: rename filesystem type to "overlay"
isofs: avoid unused function warning
vfs: fix reference leak in d_prune_aliases()
|
|
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"DeviceTree fixes for 3.18:
- two fixes for OF selftest code
- fix for PowerPC address parsing to disable work-around except on
old PowerMACs
- fix a crash when earlycon is enabled, but no device is found
- DT documentation fixes and missing vendor prefixes
All but the doc updates are also for stable"
* tag 'devicetree-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/selftest: Fix testing when /aliases is missing
of/selftest: Fix off-by-one error in removal path
documentation: pinctrl bindings: Fix trivial typo 'abitrary'
devicetree: bindings: Add vendor prefix for Micron Technology, Inc.
of: Add vendor prefix for Chips&Media, Inc.
of/base: Fix PowerPC address parsing hack
devicetree: vendor-prefixes.txt: fix whitespace
of: Fix crash if an earlycon driver is not found
of/irq: Drop obsolete 'interrupts' vs 'interrupts-extended' text
of: Spelling s/stucture/structure/
devicetree: bindings: add sandisk to the vendor prefixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
PAE kernels, an APM X-Gene problem (it depended on a generic change we
removed before merging), a fix for my hotplug device configuration
changes, and a devicetree documentation update.
Resource management:
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug:
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver:
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene:
- Assign resources to bus before adding new devices (Duc Dang)"
* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
PCI: Apply _HPX Link Control settings to all devices with a link
PCI: Add missing DT binding for "linux,pci-domain" property
PCI: xgene: Assign resources to bus before adding new devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
pull request: wireless-next 2014-11-21
Please pull this batch of updates intended for the 3.19 stream...
For the mac80211 bits, Johannes says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
For the Bluetooth bits, Johan says:
"Here's another set of patches for 3.19. Most of it is again fixes and
cleanups to ieee802154 related code from Alexander Aring. We've also got
better handling of hardware error events along with a proper API for HCI
drivers to notify the HCI core of such situations. There's also a minor
fix for mgmt events as well as a sparse warning fix. The code for
sending HCI commands synchronously also gets a fix where we might loose
the completion event in the case of very fast HW (particularly easily
reproducible with an emulated HCI device)."
And...
"Here's another bluetooth-next pull request for 3.19. We've got:
- Various fixes, cleanups and improvements to ieee802154/mac802154
- Support for a Broadcom BCM20702A1 variant
- Lots of lockdep fixes
- Fixed handling of LE CoC errors that should trigger SMP"
For the Atheros bits, Kalle says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
On top of that...both ath9k and mwifiex get their usual level of
updates. Of note is the ath9k spectral scan work from Oleksij Rempel.
I also pulled from the wireless tree in order to avoid some merge issues.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add "micrel,rmii-reference-clock-select-25-mhz" to Micrel ethernet PHY
binding documentation.
This property is needed to properly describe some revisions of Micrel
PHYs which has the function of this configuration bit inverted so that
setting it enables 25 MHz rather than 50 MHz clock mode.
Note that a clock reference ("rmii-ref") is still needed to actually
select either mode.
Cc: devicetree@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce indentation of Micrel PHY binding documentations somewhat.
Also fix "reference input clock" typo while at it.
Cc: devicetree@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Micrel KSZ8081 and KSZ8091 PHYs have the RMII Reference Clock Select
bit, which is used to select 25 or 50 MHz clock mode.
Note that on some revisions of the PHY (e.g. KSZ8081RND) the function of
this bit is inverted so that setting it enables 25 rather than 50 MHz
mode. Add a new device-tree property
"micrel,rmii-reference-clock-select-25-mhz" to describe this.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some distributions carry an "old" format of overlayfs while mainline has a
"new" format.
The distros will possibly want to keep the old overlayfs alongside the new
for compatibility reasons.
To make it possible to differentiate the two versions change the name of
the new one from "overlayfs" to "overlay".
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reported-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Andy Whitcroft <apw@canonical.com>
|
|
Recently many changes have been done inside the driver
so this patch updates the driver's doc for example reviewing
information for the rx and tx processes that are managed
by napi method, adding new information for missing glue-logic files
etc.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A misspelled 'arbitrary' propagated to quite a few locations in the DT
binding documentation for pin-controllers. Fixing by:
git grep abitrary | cut -f1 -d: | xargs sed -i 's/abitrary/arbitrary/'
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This patch is used to add vendor prefix for Micron Technology, Inc. in
the vendor-prefixes.txt file.
Micron Technology, Inc. is an American multinational corporation based
in Boise, Idaho, best known for producing many forms of semiconductor
devices. This includes DRAM, SDRAM, flash memory, eMMC and SSDs.
Signed-off-by: Bean Huo <bpqw@micron.com>
[robh: cleanup commit msg formatting and company name]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Chips&Media is a developer of Video Codec IP cores.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[robh: fix-up alphabetical ordering]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
a9ecdc0fdc54 ("of/irq: Fix lookup to use 'interrupts-extended' property
first") updated the description to say that:
- Both 'interrupts' and 'interrupts-extended' may be present
- Software should prefer 'interrupts-extended'
- Software that doesn't comprehend 'interrupts-extended' may use
'interrupts'
But there is still a paragraph at the end that prohibits having both and
says 'interrupts' should be preferred.
Remove the contradictory text.
Fixes: a9ecdc0fdc54 ("of/irq: Fix lookup to use 'interrupts-extended' property first")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.13+
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add sandisk to the list of vendors. This prefix should be used
also for companies absorbed by Sandisk, like M-Systems.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.
Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.
This patch provides infrastructure to help drivers doing the right thing.
netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.
A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.
Tested:
myhost:~# cat /proc/sys/net/core/netdev_rss_key
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41:36:40:74:b6:15:ca:27:44:aa:b3:4d:72
myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
0: 0 1 2 3 4 5 6 7
RSS hash key:
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"Mostly small fixups to PS/2 tochpad drivers (ALPS, Elantech,
Synaptics) to better deal with specific hardware"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - update the documentation
Input: elantech - provide a sysfs knob for crc_enabled
Input: elantech - report the middle button of the touchpad
Input: alps - ignore bad data on Dell Latitudes E6440 and E7440
Input: alps - allow up to 2 invalid packets without resetting device
Input: alps - ignore potential bare packets when device is out of sync
Input: elantech - fix crc_enabled for Fujitsu H730
Input: elantech - use elantech_report_trackpoint for hardware v4 too
Input: twl4030-pwrbutton - ensure a wakeup event is recorded.
Input: synaptics - add min/max quirk for Lenovo T440s
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"The most notable is the revert of lock splitting optimization in ahci.
This also made the IRQ handling threaded even when there's only one
IRQ in use. The conversion missed IRFQ_SHARED leading to screaming
IRQs problem in some cases and the threaded IRQ handling showed
performance regression in some LKP test cases. The changes are
reverted for now. It'll probably be retried once threaded IRQ
handling is removed from ahci.
Other than that, there's one fix for ahci and several patches adding
device IDs"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix AHCI parameters not taken into account
ata: sata_rcar: Add r8a7793 device support
ahci: Add Device IDs for Intel Sunrise Point PCH
ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks
Revert "AHCI: Optimize single IRQ interrupt processing"
Revert "AHCI: Do not acquire ata_host::lock from single IRQ handler"
ata: sata_rcar: Disable DIPM mode for r8a7790 ES1
|
|
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) sunhme driver lacks DMA mapping error checks, based upon a report by
Meelis Roos.
2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.
3) DMA memory allocation sizes are wrong in systemport ethernet driver,
fix from Florian Fainelli.
4) Fix use after free in mac80211 defragmentation code, from Johannes
Berg.
5) Some networking uapi headers missing from Kbuild file, from Stephen
Hemminger.
6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
and macvtap has a similar bug, from Herbert Xu.
7) Adjust several tunneling drivers to set dev->iflink after registry,
because registry sets that to -1 overwriting whatever we did. From
Steffen Klassert.
8) Geneve forgets to set inner tunneling type, causing GSO segmentation
to fail on some NICs. From Jesse Gross.
9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
Giuseppe CAVALLARO.
10) Fix spurious timeouts with NewReno on low traffic connections, from
Marcelo Leitner.
11) Fix descriptor updates in enic driver, from Govindarajulu
Varadarajan.
12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
Fix from Takashi Iwai.
13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
Borkmann.
14) psock_fanout selftest accesses past the end of the mmap ring, fix
from Shuah Khan.
15) Fix PTP timestamping for VLAN packets, from Richard Cochran.
16) netlink_unbind() calls in netlink pass wrong initial argument, from
Hiroaki SHIMODA.
17) vxlan socket reuse accidently reuses a socket when the address
family is different, so we have to explicitly check this, from
Marcelo Lietner.
18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
and other architectures, from Guenter Roeck.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
vxlan: Do not reuse sockets for a different address family
smsc911x: power-up phydev before doing a software reset.
lib: rhashtable - Remove weird non-ASCII characters from comments
net/smsc911x: Fix delays in the PHY enable/disable routines
net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
netlink: Properly unbind in error conditions.
net: ptp: fix time stamp matching logic for VLAN packets.
cxgb4 : dcb open-lldp interop fixes
selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
net: bcmgenet: apply MII configuration in bcmgenet_open()
net: bcmgenet: connect and disconnect from the PHY state machine
net: qualcomm: Fix dependency
ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
net: phy: Correctly handle MII ioctl which changes autonegotiation.
ipv6: fix IPV6_PKTINFO with v4 mapped
net: sctp: fix memory leak in auth key management
net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
net: ppp: Don't call bpf_prog_create() in ppp_lock
net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
cxgb4 : Fix bug in DCB app deletion
...
|
|
A chapter is added to describe the trackpoint packets.
A section is added to describe the behaviour of the knob crc_enabled in
sysfs.
The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
41e5c0f81d3e ("of/pci: Add pci_get_new_domain_nr() and
of_get_pci_domain_nr()") added parsing of the "linux,pci-domain" property,
but didn't add the binding documentation.
Since this property will be supported by a number of host bridge drivers,
add it to the common PCI binding doc.
Fixes: 41e5c0f81d3e ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
The device tree probing for R-Car M2N (r8a7793) is added.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable led-mode configuration for KSZ8081 and KSZ8091.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit extended the documentation of the ethernet-phy
compatible property, but placed the new paragraph under the max-speed
property.
Fixes: f00e756ed12d ("dt: Document a compatible entry for MDIO ethernet
Phys")
Cc: devicetree@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not possible to auto detect the irq numbers used by the cores on
an arm SoC. If bcma was registered with device tree it will search for
some device tree nodes with the irq number and add it to the core
configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
|
|
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
|
|
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit a4a47bc03fe520e95e0c4212bf97c86545fb14f9), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
This patch provides support for interrupts that are generated by the
Tx/Rx DMA channel pairs of the device. This allows for Tx and Rx
processing to run across multiple processsors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was initially sent by Lorenzo Colitti, but was subsequently
lost in the final diff he submitted.
Signed-off-by: Loganaden Velvindron <logan@elandsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal fixes from Eduardo Valentin:
"Specifics:
- a few code fixes improving the Exynos code base. They remove dead
and unreachable code. No functional changes here
- in Exynos code base, fixes regarding the right usage of features
(TRIMINFO and TRIMRELOAD)
- documentation of RCAR thermal
- fix in the of-thermal, regarding the proper usage of of-APIs
- fixes on thermal-core, removal of unreachable code"
[ Eduardo is sending the thermal fixes on behalf of Rui Zhang this time.
Rui is currently unable to send pull requests due to troubles with his
machine and he's currently in a business trip ]
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
Thermal:Remove usless if(!result) before return tz
thermal: exynos: fix IRQ clearing on TMU initialization
thermal: fix multiple disbalanced device node counters
thermal: rcar: Add binding docs for new R-Car Gen2 SoCs
thermal: exynos: Add support for TRIM_RELOAD feature at Exynos3250
thermal: exynos: Add support for many TRIMINFO_CTRL registers
thermal: samsung: Exynos5260 and Exynos5420 should not use TRIM_RELOAD flag
thermal: exynos: remove identical values from exynos*_tmu_registers structures
thermal: exynos: remove redundant pdata checks from exynos_tmu_control()
thermal: exynos: cache non_hw_trigger_levels in pdata
thermal: exynos: simplify temp_to_code() and code_to_temp()
thermal: exynos: remove redundant threshold_code checks from exynos_tmu_initialize()
thermal: exynos: remove redundant pdata checks from exynos_tmu_initialize()
thermal: exynos: remove dead code for HW_MODE calibration
thermal: exynos: remove unused struct exynos_tmu_registers entries
|
|
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
- r8a7792 (R-Car V2H)
- r8a7793 (R-Car M2-N)
- r8a7794 (R-Car E2)
r8a7791 is now called "R-Car M2-W".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Conflicts:
drivers/net/phy/marvell.c
Simple overlapping changes in drivers/net/phy/marvell.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
|
|
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
|
|
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
