| Age | Commit message (Collapse) | Author |
|---|
|
Due to a small omission, the offload_failed flag is missing from ipv4
fibmatch results. Make sure it is set correctly.
The issue can be witnessed using the following commands:
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add dummy1 up type dummy
ip route add 192.0.2.0/24 dev dummy1
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/fib/fail_route_offload
ip route add 198.51.100.0/24 dev dummy1
ip route
# 192.168.15.0/24 has rt_trap
# 198.51.100.0/24 has rt_offload_failed
ip route get 192.168.15.1 fibmatch
# Result has rt_trap
ip route get 198.51.100.1 fibmatch
# Result differs from the route shown by `ip route`, it is missing
# rt_offload_failed
ip link del dev dummy1
echo 1 > /sys/bus/netdevsim/del_device
Fixes: 36c5100e859d ("IPv4: Add "offload failed" indication to routes")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230926182730.231208-1-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Quite a collection of fixes this time, really too many
to list individually. Many stack fixes, even rfkill
(found by simulation and the new eevdf scheduler)!
Also a bigger maintainers file cleanup, to remove old
and redundant information.
* tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (32 commits)
wifi: iwlwifi: mvm: Fix incorrect usage of scan API
wifi: mac80211: Create resources for disabled links
wifi: cfg80211: avoid leaking stack data into trace
wifi: mac80211: allow transmitting EAPOL frames with tainted key
wifi: mac80211: work around Cisco AP 9115 VHT MPDU length
wifi: cfg80211: Fix 6GHz scan configuration
wifi: mac80211: fix potential key leak
wifi: mac80211: fix potential key use-after-free
wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
wifi: brcmfmac: Replace 1-element arrays with flexible arrays
wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
wifi: rtw88: rtw8723d: Fix MAC address offset in EEPROM
rfkill: sync before userspace visibility/changes
wifi: mac80211: fix mesh id corruption on 32 bit systems
wifi: cfg80211: add missing kernel-doc for cqm_rssi_work
wifi: cfg80211: fix cqm_config access race
wifi: iwlwifi: mvm: Fix a memory corruption issue
wifi: iwlwifi: Ensure ack flag is properly cleared.
wifi: iwlwifi: dbg_ini: fix structure packing
iwlwifi: mvm: handle PS changes in vif_cfg_changed
...
====================
Link: https://lore.kernel.org/r/20230927095835.25803-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-10-02
We've added 11 non-merge commits during the last 12 day(s) which contain
a total of 12 files changed, 176 insertions(+), 41 deletions(-).
The main changes are:
1) Fix BPF verifier to reset backtrack_state masks on global function
exit as otherwise subsequent precision tracking would reuse them,
from Andrii Nakryiko.
2) Several sockmap fixes for available bytes accounting,
from John Fastabend.
3) Reject sk_msg egress redirects to non-TCP sockets given this
is only supported for TCP sockets today, from Jakub Sitnicki.
4) Fix a syzkaller splat in bpf_mprog when hitting maximum program
limits with BPF_F_BEFORE directive, from Daniel Borkmann
and Nikolay Aleksandrov.
5) Fix BPF memory allocator to use kmalloc_size_roundup() to adjust
size_index for selecting a bpf_mem_cache, from Hou Tao.
6) Fix arch_prepare_bpf_trampoline return code for s390 JIT,
from Song Liu.
7) Fix bpf_trampoline_get when CONFIG_BPF_JIT is turned off,
from Leon Hwang.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Use kmalloc_size_roundup() to adjust size_index
selftest/bpf: Add various selftests for program limits
bpf, mprog: Fix maximum program check on mprog attachment
bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
bpf, sockmap: Add tests for MSG_F_PEEK
bpf, sockmap: Do not inc copied_seq when PEEK flag set
bpf: tcp_read_skb needs to pop skb regardless of seq
bpf: unconditionally reset backtrack_state masks on global func exit
bpf: Fix tr dereferencing
selftests/bpf: Check bpf_cubic_acked() is called via struct_ops
s390/bpf: Let arch_prepare_bpf_trampoline return program size
====================
Link: https://lore.kernel.org/r/20231002113417.2309-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Fixes: 7525de2516fb ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the while loop of vringh_iov_xfer(), `partlen` could be 0 if one of
the `iov` has 0 lenght.
In this case, we should skip the iov and go to the next one.
But calling vringh_kiov_advance() with 0 lenght does not cause the
advancement, since it returns immediately if asked to advance by 0 bytes.
Let's restore the code that was there before commit b8c06ad4d67d
("vringh: implement vringh_kiov_advance()"), avoiding using
vringh_kiov_advance().
Fixes: b8c06ad4d67d ("vringh: implement vringh_kiov_advance()")
Cc: stable@vger.kernel.org
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.
The value is calculated by
MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device list needs its associated lock held when modifying it, or the
list could become corrupted, as syzbot discovered.
Reported-and-tested-by: syzbot+c1d0a03d305972dbbe14@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c1d0a03d305972dbbe14
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 6709d4b7bc2e ("net: nfc: Fix use-after-free caused by nfc_llcp_find_local")
Link: https://lore.kernel.org/r/20230908235853.1319596-1-jeremy@jcline.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ETHTOOL_A_PLCA_ENABLED data type is u8. But while parsing the
value from the attribute, nla_get_u32() is used in the plca_update_sint()
function instead of nla_get_u8(). So plca_cfg.enabled variable is updated
with some garbage value instead of 0 or 1 and always enables plca even
though plca is disabled through ethtool application. This bug has been
fixed by parsing the values based on the attributes type in the policy.
Fixes: 8580e16c28f3 ("net/ethtool: add netlink interface for the PLCA RS")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230908044548.5878-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The flexible structure (a structure that contains a flexible-array member
at the end) `qed_ll2_tx_packet` is nested within the second layer of
`struct qed_ll2_info`:
struct qed_ll2_tx_packet {
...
/* Flexible Array of bds_set determined by max_bds_per_packet */
struct {
struct core_tx_bd *txq_bd;
dma_addr_t tx_frag;
u16 frag_len;
} bds_set[];
};
struct qed_ll2_tx_queue {
...
struct qed_ll2_tx_packet cur_completing_packet;
};
struct qed_ll2_info {
...
struct qed_ll2_tx_queue tx_queue;
struct qed_ll2_cbs cbs;
};
The problem is that member `cbs` in `struct qed_ll2_info` is placed just
after an object of type `struct qed_ll2_tx_queue`, which is in itself
an implicit flexible structure, which by definition ends in a flexible
array member, in this case `bds_set`. This causes an undefined behavior
bug at run-time when dynamic memory is allocated for `bds_set`, which
could lead to a serious issue if `cbs` in `struct qed_ll2_info` is
overwritten by the contents of `bds_set`. Notice that the type of `cbs`
is a structure full of function pointers (and a cookie :) ):
include/linux/qed/qed_ll2_if.h:
107 typedef
108 void (*qed_ll2_complete_rx_packet_cb)(void *cxt,
109 struct qed_ll2_comp_rx_data *data);
110
111 typedef
112 void (*qed_ll2_release_rx_packet_cb)(void *cxt,
113 u8 connection_handle,
114 void *cookie,
115 dma_addr_t rx_buf_addr,
116 bool b_last_packet);
117
118 typedef
119 void (*qed_ll2_complete_tx_packet_cb)(void *cxt,
120 u8 connection_handle,
121 void *cookie,
122 dma_addr_t first_frag_addr,
123 bool b_last_fragment,
124 bool b_last_packet);
125
126 typedef
127 void (*qed_ll2_release_tx_packet_cb)(void *cxt,
128 u8 connection_handle,
129 void *cookie,
130 dma_addr_t first_frag_addr,
131 bool b_last_fragment, bool b_last_packet);
132
133 typedef
134 void (*qed_ll2_slowpath_cb)(void *cxt, u8 connection_handle,
135 u32 opaque_data_0, u32 opaque_data_1);
136
137 struct qed_ll2_cbs {
138 qed_ll2_complete_rx_packet_cb rx_comp_cb;
139 qed_ll2_release_rx_packet_cb rx_release_cb;
140 qed_ll2_complete_tx_packet_cb tx_comp_cb;
141 qed_ll2_release_tx_packet_cb tx_release_cb;
142 qed_ll2_slowpath_cb slowpath_cb;
143 void *cookie;
144 };
Fix this by moving the declaration of `cbs` to the middle of its
containing structure `qed_ll2_info`, preventing it from being
overwritten by the contents of `bds_set` at run-time.
This bug was introduced in 2017, when `bds_set` was converted to a
one-element array, and started to be used as a Variable Length Object
(VLO) at run-time.
Fixes: f5823fe6897c ("qed: Add ll2 option to limit the number of bds per packet")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ZQ+Nz8DfPg56pIzr@work
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzbot reported the following uninit-value access issue:
=====================================================
BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x21c/0x280 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737
usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374
really_probe+0xf20/0x20b0 drivers/base/dd.c:529
driver_probe_device+0x293/0x390 drivers/base/dd.c:701
__device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
__device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032
usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241
usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272
really_probe+0xf20/0x20b0 drivers/base/dd.c:529
driver_probe_device+0x293/0x390 drivers/base/dd.c:701
__device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
__device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554
hub_port_connect drivers/usb/core/hub.c:5208 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5348 [inline]
port_event drivers/usb/core/hub.c:5494 [inline]
hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576
process_one_work+0x1688/0x2140 kernel/workqueue.c:2269
worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415
kthread+0x551/0x590 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293
Local variable ----buf.i87@smsc75xx_bind created at:
__smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
__smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.
This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit b0e214d21203 ("netfilter: keep conntrack reference until
IPsecv6 policy checks are done") is a direct copy of the old
commit b59c270104f0 ("[NETFILTER]: Keep conntrack reference until
IPsec policy checks are done") but for IPv6. However, it also
copies a bug that this old commit had. That is: when the third
packet of 3WHS connection establishment contains payload, it is
added into socket receive queue without the XFRM check and the
drop of connection tracking context.
That leads to nf_conntrack module being impossible to unload as
it waits for all the conntrack references to be dropped while
the packet release is deferred in per-cpu cache indefinitely, if
not consumed by the application.
The issue for IPv4 was fixed in commit 6f0012e35160 ("tcp: add a
missing nf_reset_ct() in 3WHS handling") by adding a missing XFRM
check and correctly dropping the conntrack context. However, the
issue was introduced to IPv6 code afterwards. Fixing it the
same way for IPv6 now.
Fixes: b0e214d21203 ("netfilter: keep conntrack reference until IPsecv6 policy checks are done")
Link: https://lore.kernel.org/netdev/d589a999-d4dd-2768-b2d5-89dec64a4a42@ovn.org/
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230922210530.2045146-1-i.maximets@ovn.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After deleting an interface address in fib_del_ifaddr(), the function
scans the fib_info list for stray entries and calls fib_flush() and
fib_table_flush(). Then the stray entries will be deleted silently and no
RTM_DELROUTE notification will be sent.
This lack of notification can make routing daemons, or monitor like
`ip monitor route` miss the routing changes. e.g.
+ ip link add dummy1 type dummy
+ ip link add dummy2 type dummy
+ ip link set dummy1 up
+ ip link set dummy2 up
+ ip addr add 192.168.5.5/24 dev dummy1
+ ip route add 7.7.7.0/24 dev dummy2 src 192.168.5.5
+ ip -4 route
7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5
As Ido reminded, fib_table_flush() isn't only called when an address is
deleted, but also when an interface is deleted or put down. The lack of
notification in these cases is deliberate. And commit 7c6bb7d2faaf
("net/ipv6: Add knob to skip DELROUTE message on device down") introduced
a sysctl to make IPv6 behave like IPv4 in this regard. So we can't send
the route delete notify blindly in fib_table_flush().
To fix this issue, let's add a new flag in "struct fib_info" to track the
deleted prefer source address routes, and only send notify for them.
After update:
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5
Deleted 7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
Suggested-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230922075508.848925-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.
Fixes: 773bda964921 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the change in commit 0bdf399342c5("net: Avoid address
overwrite in kernel_connect"), BPF hooks run on bind may rewrite the
address passed to kernel_bind(). This change
1) Makes a copy of the bind address in kernel_bind() to insulate
callers.
2) Replaces direct calls to sock->ops->bind() in net with kernel_bind()
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 4fbac77d2d09 ("bpf: Hooks for sys_bind")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Callers of sock_sendmsg(), and similarly kernel_sendmsg(), in kernel
space may observe their value of msg_name change in cases where BPF
sendmsg hooks rewrite the send address. This has been confirmed to break
NFS mounts running in UDP mode and has the potential to break other
systems.
This patch:
1) Creates a new function called __sock_sendmsg() with same logic as the
old sock_sendmsg() function.
2) Replaces calls to sock_sendmsg() made by __sys_sendto() and
__sys_sendmsg() with __sock_sendmsg() to avoid an unnecessary copy,
as these system calls are already protected.
3) Modifies sock_sendmsg() so that it makes a copy of msg_name if
present before passing it down the stack to insulate callers from
changes to the send address.
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 1cedee13d25a ("bpf: Hooks for sys_sendmsg")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 0bdf399342c5 ("net: Avoid address overwrite in kernel_connect")
ensured that kernel_connect() will not overwrite the address parameter
in cases where BPF connect hooks perform an address rewrite. This change
replaces direct calls to sock->ops->connect() in net with kernel_connect()
to make these call safe.
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: d74bad4e74ee ("bpf: Hooks for sys_connect")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Including the transhdrlen in length is a problem when the packet is
partially filled (e.g. something like send(MSG_MORE) happened previously)
when appending to an IPv4 or IPv6 packet as we don't want to repeat the
transport header or account for it twice. This can happen under some
circumstances, such as splicing into an L2TP socket.
The symptom observed is a warning in __ip6_append_data():
WARNING: CPU: 1 PID: 5042 at net/ipv6/ip6_output.c:1800 __ip6_append_data.isra.0+0x1be8/0x47f0 net/ipv6/ip6_output.c:1800
that occurs when MSG_SPLICE_PAGES is used to append more data to an already
partially occupied skbuff. The warning occurs when 'copy' is larger than
the amount of data in the message iterator. This is because the requested
length includes the transport header length when it shouldn't. This can be
triggered by, for example:
sfd = socket(AF_INET6, SOCK_DGRAM, IPPROTO_L2TP);
bind(sfd, ...); // ::1
connect(sfd, ...); // ::1 port 7
send(sfd, buffer, 4100, MSG_MORE);
sendfile(sfd, dfd, NULL, 1024);
Fix this by only adding transhdrlen into the length if the write queue is
empty in l2tp_ip6_sendmsg(), analogously to how UDP does things.
l2tp_ip_sendmsg() looks like it won't suffer from this problem as it builds
the UDP packet itself.
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Reported-by: syzbot+62cbf263225ae13ff153@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/0000000000001c12b30605378ce8@google.com/
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Dumazet <edumazet@google.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: David Ahern <dsahern@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: netdev@vger.kernel.org
cc: bpf@vger.kernel.org
cc: syzkaller-bugs@googlegroups.com
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
n->output field can be read locklessly, while a writer
might change the pointer concurrently.
Add missing annotations to prevent load-store tearing.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.
Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.
I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
bluetooth pull request for net:
- Fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER
- Fix handling of listen for ISO unicast
- Fix build warnings
- Fix leaking content of local_codecs
- Add shutdown function for QCA6174
- Delete unused hci_req_prepare_suspend() declaration
- Fix hci_link_tx_to RCU lock usage
- Avoid redundant authentication
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The second parameter of stmmac_pltfr_init() needs the pointer of
"struct plat_stmmacenet_data". So, correct the parameter typo when calling the
function.
Otherwise, it may cause this alignment exception when doing suspend/resume.
[ 49.067201] CPU1 is up
[ 49.135258] Internal error: SP/PC alignment exception: 000000008a000000 [#1] PREEMPT SMP
[ 49.143346] Modules linked in: soc_imx9 crct10dif_ce polyval_ce nvmem_imx_ocotp_fsb_s400 polyval_generic layerscape_edac_mod snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_imx_card snd_soc_wm8962 el_enclave snd_soc_fsl_micfil rtc_pcf2127 rtc_pcf2131 flexcan can_dev snd_soc_fsl_xcvr snd_soc_fsl_sai imx8_media_dev(C) snd_soc_fsl_utils fuse
[ 49.173393] CPU: 0 PID: 565 Comm: sh Tainted: G C 6.5.0-rc4-next-20230804-05047-g5781a6249dae #677
[ 49.183721] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[ 49.189190] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 49.196140] pc : 0x80800052
[ 49.198931] lr : stmmac_pltfr_resume+0x34/0x50
[ 49.203368] sp : ffff800082f8bab0
[ 49.206670] x29: ffff800082f8bab0 x28: ffff0000047d0ec0 x27: ffff80008186c170
[ 49.213794] x26: 0000000b5e4ff1ba x25: ffff800081e5fa74 x24: 0000000000000010
[ 49.220918] x23: ffff800081fe0000 x22: 0000000000000000 x21: 0000000000000000
[ 49.228042] x20: ffff0000001b4010 x19: ffff0000001b4010 x18: 0000000000000006
[ 49.235166] x17: ffff7ffffe007000 x16: ffff800080000000 x15: 0000000000000000
[ 49.242290] x14: 00000000000000fc x13: 0000000000000000 x12: 0000000000000000
[ 49.249414] x11: 0000000000000001 x10: 0000000000000a60 x9 : ffff800082f8b8c0
[ 49.256538] x8 : 0000000000000008 x7 : 0000000000000001 x6 : 000000005f54a200
[ 49.263662] x5 : 0000000001000000 x4 : ffff800081b93680 x3 : ffff800081519be0
[ 49.270786] x2 : 0000000080800052 x1 : 0000000000000000 x0 : ffff0000001b4000
[ 49.277911] Call trace:
[ 49.280346] 0x80800052
[ 49.282781] platform_pm_resume+0x2c/0x68
[ 49.286785] dpm_run_callback.constprop.0+0x74/0x134
[ 49.291742] device_resume+0x88/0x194
[ 49.295391] dpm_resume+0x10c/0x230
[ 49.298866] dpm_resume_end+0x18/0x30
[ 49.302515] suspend_devices_and_enter+0x2b8/0x624
[ 49.307299] pm_suspend+0x1fc/0x348
[ 49.310774] state_store+0x80/0x104
[ 49.314258] kobj_attr_store+0x18/0x2c
[ 49.318002] sysfs_kf_write+0x44/0x54
[ 49.321659] kernfs_fop_write_iter+0x120/0x1ec
[ 49.326088] vfs_write+0x1bc/0x300
[ 49.329485] ksys_write+0x70/0x104
[ 49.332874] __arm64_sys_write+0x1c/0x28
[ 49.336783] invoke_syscall+0x48/0x114
[ 49.340527] el0_svc_common.constprop.0+0xc4/0xe4
[ 49.345224] do_el0_svc+0x38/0x98
[ 49.348526] el0_svc+0x2c/0x84
[ 49.351568] el0t_64_sync_handler+0x100/0x12c
[ 49.355910] el0t_64_sync+0x190/0x194
[ 49.359567] Code: ???????? ???????? ???????? ???????? (????????)
[ 49.365644] ---[ end trace 0000000000000000 ]---
Fixes: 97117eb51ec8 ("net: stmmac: platform: provide stmmac_pltfr_init()")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d52b59315bf5 ("bpf: Adjust size_index according to the value of
KMALLOC_MIN_SIZE") uses KMALLOC_MIN_SIZE to adjust size_index, but as
reported by Nathan, the adjustment is not enough, because
__kmalloc_minalign() also decides the minimal alignment of slab object
as shown in new_kmalloc_cache() and its value may be greater than
KMALLOC_MIN_SIZE (e.g., 64 bytes vs 8 bytes under a riscv QEMU VM).
Instead of invoking __kmalloc_minalign() in bpf subsystem to find the
maximal alignment, just using kmalloc_size_roundup() directly to get the
corresponding slab object size for each allocation size. If these two
sizes are unmatched, adjust size_index to select a bpf_mem_cache with
unit_size equal to the object_size of the underlying slab cache for the
allocation size.
Fixes: 822fb26bdb55 ("bpf: Add a hint to allocated objects.")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/bpf/20230914181407.GA1000274@dev-arch.thelio-3990X/
Signed-off-by: Hou Tao <houtao1@huawei.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/r/20230928101558.2594068-1-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add various tests to check maximum number of supported programs
being attached:
# ./vmtest.sh -- ./test_progs -t tc_opts
[...]
./test_progs -t tc_opts
[ 1.185325] bpf_testmod: loading out-of-tree module taints kernel.
[ 1.186826] bpf_testmod: module verification failed: signature and/or required key missing - tainting kernel
[ 1.270123] tsc: Refined TSC clocksource calibration: 3407.988 MHz
[ 1.272428] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x311fc932722, max_idle_ns: 440795381586 ns
[ 1.276408] clocksource: Switched to clocksource tsc
#252 tc_opts_after:OK
#253 tc_opts_append:OK
#254 tc_opts_basic:OK
#255 tc_opts_before:OK
#256 tc_opts_chain_classic:OK
#257 tc_opts_chain_mixed:OK
#258 tc_opts_delete_empty:OK
#259 tc_opts_demixed:OK
#260 tc_opts_detach:OK
#261 tc_opts_detach_after:OK
#262 tc_opts_detach_before:OK
#263 tc_opts_dev_cleanup:OK
#264 tc_opts_invalid:OK
#265 tc_opts_max:OK <--- (new test)
#266 tc_opts_mixed:OK
#267 tc_opts_prepend:OK
#268 tc_opts_replace:OK
#269 tc_opts_revision:OK
Summary: 18/0 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20230929204121.20305-2-daniel@iogearbox.net
|
|
After Paul's recent improvement to syzkaller to improve coverage for
bpf_mprog and tcx, it hit a splat that the program limit was surpassed.
What happened is that the maximum number of progs got added, followed
by another prog add request which adds with BPF_F_BEFORE flag relative
to the last program in the array. The idx >= bpf_mprog_max() check in
bpf_mprog_attach() still passes because the index is below the maximum
but the maximum will be surpassed. We need to add a check upfront for
insertions to catch this situation.
Fixes: 053c8e1f235d ("bpf: Add generic attach/detach/query API for multi-progs")
Reported-by: syzbot+baa44e3dbbe48e05c1ad@syzkaller.appspotmail.com
Reported-by: syzbot+b97d20ed568ce0951a06@syzkaller.appspotmail.com
Reported-by: syzbot+2558ca3567a77b7af4e3@syzkaller.appspotmail.com
Co-developed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: syzbot+baa44e3dbbe48e05c1ad@syzkaller.appspotmail.com
Tested-by: syzbot+b97d20ed568ce0951a06@syzkaller.appspotmail.com
Link: https://github.com/google/syzkaller/pull/4207
Link: https://lore.kernel.org/bpf/20230929204121.20305-1-daniel@iogearbox.net
|
|
With a SOCKMAP/SOCKHASH map and an sk_msg program user can steer messages
sent from one TCP socket (s1) to actually egress from another TCP
socket (s2):
tcp_bpf_sendmsg(s1) // = sk_prot->sendmsg
tcp_bpf_send_verdict(s1) // __SK_REDIRECT case
tcp_bpf_sendmsg_redir(s2)
tcp_bpf_push_locked(s2)
tcp_bpf_push(s2)
tcp_rate_check_app_limited(s2) // expects tcp_sock
tcp_sendmsg_locked(s2) // ditto
There is a hard-coded assumption in the call-chain, that the egress
socket (s2) is a TCP socket.
However in commit 122e6c79efe1 ("sock_map: Update sock type checks for
UDP") we have enabled redirects to non-TCP sockets. This was done for the
sake of BPF sk_skb programs. There was no indention to support sk_msg
send-to-egress use case.
As a result, attempts to send-to-egress through a non-TCP socket lead to a
crash due to invalid downcast from sock to tcp_sock:
BUG: kernel NULL pointer dereference, address: 000000000000002f
...
Call Trace:
<TASK>
? show_regs+0x60/0x70
? __die+0x1f/0x70
? page_fault_oops+0x80/0x160
? do_user_addr_fault+0x2d7/0x800
? rcu_is_watching+0x11/0x50
? exc_page_fault+0x70/0x1c0
? asm_exc_page_fault+0x27/0x30
? tcp_tso_segs+0x14/0xa0
tcp_write_xmit+0x67/0xce0
__tcp_push_pending_frames+0x32/0xf0
tcp_push+0x107/0x140
tcp_sendmsg_locked+0x99f/0xbb0
tcp_bpf_push+0x19d/0x3a0
tcp_bpf_sendmsg_redir+0x55/0xd0
tcp_bpf_send_verdict+0x407/0x550
tcp_bpf_sendmsg+0x1a1/0x390
inet_sendmsg+0x6a/0x70
sock_sendmsg+0x9d/0xc0
? sockfd_lookup_light+0x12/0x80
__sys_sendto+0x10e/0x160
? syscall_enter_from_user_mode+0x20/0x60
? __this_cpu_preempt_check+0x13/0x20
? lockdep_hardirqs_on+0x82/0x110
__x64_sys_sendto+0x1f/0x30
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Reject selecting a non-TCP sockets as redirect target from a BPF sk_msg
program to prevent the crash. When attempted, user will receive an EACCES
error from send/sendto/sendmsg() syscall.
Fixes: 122e6c79efe1 ("sock_map: Update sock type checks for UDP")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20230920102055.42662-1-jakub@cloudflare.com
|
|
Test that we can read with MSG_F_PEEK and then still get correct number
of available bytes through FIONREAD. The recv() (without PEEK) then
returns the bytes as expected. The recv() always worked though because
it was just the available byte reporting that was broke before latest
fixes.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230926035300.135096-4-john.fastabend@gmail.com
|
|
When data is peek'd off the receive queue we shouldn't considered it
copied from tcp_sock side. When we increment copied_seq this will confuse
tcp_data_ready() because copied_seq can be arbitrarily increased. From
application side it results in poll() operations not waking up when
expected.
Notice tcp stack without BPF recvmsg programs also does not increment
copied_seq.
We broke this when we moved copied_seq into recvmsg to only update when
actual copy was happening. But, it wasn't working correctly either before
because the tcp_data_ready() tried to use the copied_seq value to see
if data was read by user yet. See fixes tags.
Fixes: e5c6de5fa0258 ("bpf, sockmap: Incorrectly handling copied_seq")
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230926035300.135096-3-john.fastabend@gmail.com
|
|
Before fix e5c6de5fa0258 tcp_read_skb() would increment the tp->copied-seq
value. This (as described in the commit) would cause an error for apps
because once that is incremented the application might believe there is no
data to be read. Then some apps would stall or abort believing no data is
available.
However, the fix is incomplete because it introduces another issue in
the skb dequeue. The loop does tcp_recv_skb() in a while loop to consume
as many skbs as possible. The problem is the call is ...
tcp_recv_skb(sk, seq, &offset)
... where 'seq' is:
u32 seq = tp->copied_seq;
Now we can hit a case where we've yet incremented copied_seq from BPF side,
but then tcp_recv_skb() fails this test ...
if (offset < skb->len || (TCP_SKB_CB(skb)->tcp_flags & TCPHDR_FIN))
... so that instead of returning the skb we call tcp_eat_recv_skb() which
frees the skb. This is because the routine believes the SKB has been collapsed
per comment:
/* This looks weird, but this can happen if TCP collapsing
* splitted a fat GRO packet, while we released socket lock
* in skb_splice_bits()
*/
This can't happen here we've unlinked the full SKB and orphaned it. Anyways
it would confuse any BPF programs if the data were suddenly moved underneath
it.
To fix this situation do simpler operation and just skb_peek() the data
of the queue followed by the unlink. It shouldn't need to check this
condition and tcp_read_skb() reads entire skbs so there is no need to
handle the 'offset!=0' case as we would see in tcp_read_sock().
Fixes: e5c6de5fa0258 ("bpf, sockmap: Incorrectly handling copied_seq")
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230926035300.135096-2-john.fastabend@gmail.com
|
|
When the PF and VF drivers both support flexible rx descriptors and have
negotiated the VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC capability, the VF driver
queries the PF for the list of supported descriptor formats
(VIRTCHNL_OP_GET_SUPPORTED_RXDIDS). The PF driver is supposed to set the
supported_rxdids bits that correspond to the descriptor formats the
firmware implements. The legacy 32-byte rx desc format is always
supported, even though it is not expressed in GLFLXP_RXDID_FLAGS.
The ice driver does not advertise the legacy 32-byte rx desc support,
which leads to this failure to bring up the VF using the Intel
out-of-tree iavf driver:
iavf 0000:41:01.0: PF does not list support for default Rx descriptor format
...
iavf 0000:41:01.0: PF returned error -5 (VIRTCHNL_STATUS_ERR_PARAM) to our request 6
The in-tree iavf driver does not expose this bug, because it does not
yet implement VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC.
The ice driver must always set the ICE_RXDID_LEGACY_1 bit in
supported_rxdids. The Intel out-of-tree ice driver and the ice driver in
DPDK both do this.
I copied this piece of the code and the comment text from the Intel
out-of-tree driver.
Fixes: e753df8fbca5 ("ice: Add support Flex RXD")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20230920115439.61172-1-mschmidt@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The support for using link ID in the scan request API was only
added in version 16. However, the code wrongly enabled this
API usage also for older versions. Fix it.
Reported-by: Antoine Beaupré <anarcat@debian.org>
Fixes: e98b23d0d7b8 ("wifi: iwlwifi: mvm: Add support for SCAN API version 16")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926165546.086e635fbbe6.Ia660f35ca0b1079f2c2ea92fd8d14d8101a89d03@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When associating to an MLD AP, links may be disabled. Create all
resources associated with a disabled link so that we can later enable it
without having to create these resources on the fly.
Fixes: 6d543b34dbcf ("wifi: mac80211: Support disabled links during association")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://lore.kernel.org/r/20230925173028.f9afdb26f6c7.I4e6e199aaefc1bf017362d64f3869645fa6830b5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the structure is not initialized then boolean types might be copied
into the tracing data without being initialised. This causes data from
the stack to leak into the trace and also triggers a UBSAN failure which
can easily be avoided here.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://lore.kernel.org/r/20230925171855.a9271ef53b05.I8180bae663984c91a3e036b87f36a640ba409817@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Lower layer device driver stop/wake TX by calling ieee80211_stop_queue()/
ieee80211_wake_queue() while hw scan. Sometimes hw scan and PTK rekey are
running in parallel, when M4 sent from wpa_supplicant arrive while the TX
queue is stopped, then the M4 will pending send, and then new key install
from wpa_supplicant. After TX queue wake up by lower layer device driver,
the M4 will be dropped by below call stack.
When key install started, the current key flag is set KEY_FLAG_TAINTED in
ieee80211_pairwise_rekey(), and then mac80211 wait key install complete by
lower layer device driver. Meanwhile ieee80211_tx_h_select_key() will return
TX_DROP for the M4 in step 12 below, and then ieee80211_free_txskb() called
by ieee80211_tx_dequeue(), so the M4 will not send and free, then the rekey
process failed becaue AP not receive M4. Please see details in steps below.
There are a interval between KEY_FLAG_TAINTED set for current key flag and
install key complete by lower layer device driver, the KEY_FLAG_TAINTED is
set in this interval, all packet including M4 will be dropped in this
interval, the interval is step 8~13 as below.
issue steps:
TX thread install key thread
1. stop_queue -idle-
2. sending M4 -idle-
3. M4 pending -idle-
4. -idle- starting install key from wpa_supplicant
5. -idle- =>ieee80211_key_replace()
6. -idle- =>ieee80211_pairwise_rekey() and set
currently key->flags |= KEY_FLAG_TAINTED
7. -idle- =>ieee80211_key_enable_hw_accel()
8. -idle- =>drv_set_key() and waiting key install
complete from lower layer device driver
9. wake_queue -waiting state-
10. re-sending M4 -waiting state-
11. =>ieee80211_tx_h_select_key() -waiting state-
12. drop M4 by KEY_FLAG_TAINTED -waiting state-
13. -idle- install key complete with success/fail
success: clear flag KEY_FLAG_TAINTED
fail: start disconnect
Hence add check in step 11 above to allow the EAPOL send out in the
interval. If lower layer device driver use the old key/cipher to encrypt
the M4, then AP received/decrypt M4 correctly, after M4 send out, lower
layer device driver install the new key/cipher to hardware and return
success.
If lower layer device driver use new key/cipher to send the M4, then AP
will/should drop the M4, then it is same result with this issue, AP will/
should kick out station as well as this issue.
issue log:
kworker/u16:4-5238 [000] 6456.108926: stop_queue: phy1 queue:0, reason:0
wpa_supplicant-961 [003] 6456.119737: rdev_tx_control_port: wiphy_name=phy1 name=wlan0 ifindex=6 dest=ARRAY[9e, 05, 31, 20, 9b, d0] proto=36488 unencrypted=0
wpa_supplicant-961 [003] 6456.119839: rdev_return_int_cookie: phy1, returned 0, cookie: 504
wpa_supplicant-961 [003] 6456.120287: rdev_add_key: phy1, netdev:wlan0(6), key_index: 0, mode: 0, pairwise: true, mac addr: 9e:05:31:20:9b:d0
wpa_supplicant-961 [003] 6456.120453: drv_set_key: phy1 vif:wlan0(2) sta:9e:05:31:20:9b:d0 cipher:0xfac04, flags=0x9, keyidx=0, hw_key_idx=0
kworker/u16:9-3829 [001] 6456.168240: wake_queue: phy1 queue:0, reason:0
kworker/u16:9-3829 [001] 6456.168255: drv_wake_tx_queue: phy1 vif:wlan0(2) sta:9e:05:31:20:9b:d0 ac:0 tid:7
kworker/u16:9-3829 [001] 6456.168305: cfg80211_control_port_tx_status: wdev(1), cookie: 504, ack: false
wpa_supplicant-961 [003] 6459.167982: drv_return_int: phy1 - -110
issue call stack:
nl80211_frame_tx_status+0x230/0x340 [cfg80211]
cfg80211_control_port_tx_status+0x1c/0x28 [cfg80211]
ieee80211_report_used_skb+0x374/0x3e8 [mac80211]
ieee80211_free_txskb+0x24/0x40 [mac80211]
ieee80211_tx_dequeue+0x644/0x954 [mac80211]
ath10k_mac_tx_push_txq+0xac/0x238 [ath10k_core]
ath10k_mac_op_wake_tx_queue+0xac/0xe0 [ath10k_core]
drv_wake_tx_queue+0x80/0x168 [mac80211]
__ieee80211_wake_txqs+0xe8/0x1c8 [mac80211]
_ieee80211_wake_txqs+0xb4/0x120 [mac80211]
ieee80211_wake_txqs+0x48/0x80 [mac80211]
tasklet_action_common+0xa8/0x254
tasklet_action+0x2c/0x38
__do_softirq+0xdc/0x384
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230801064751.25803-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cisco AP module 9115 with FW 17.3 has a bug and sends a too
large maximum MPDU length in the association response
(indicating 12k) that it cannot actually process.
Work around that by taking the minimum between what's in the
association response and the BSS elements (from beacon or
probe response).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230918140607.d1966a9a532e.I090225babb7cd4d1081ee9acd40e7de7e41c15ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the scan request includes a non broadcast BSSID, when adding the
scan parameters for 6GHz collocated scanning, do not include entries
that do not match the given BSSID.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230918140607.6d31d2a96baf.I6c4e3e3075d1d1878ee41f45190fdc6b86f18708@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When returning from ieee80211_key_link(), the key needs to
have been freed or successfully installed. This was missed
in a number of error paths, fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: fdf7cb4185b6 ("mac80211: accept key reinstall without changing anything")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On MT76x0, LNA gain should be applied for both external and internal LNA.
On MT76x2, LNA gain should be treated as 0 for external LNA.
Move the LNA type based logic to mt76x2 in order to fix mt76x0.
Fixes: 2daa67588f34 ("mt76x0: unify lna_gain parsing")
Reported-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230919194747.31647-1-nbd@nbd.name
|
|
in uhdlc_close()
Process the result of hdlc_open() and call uhdlc_close()
in case of an error. It is necessary to pass the error
code up the control flow, similar to a possible
error in request_irq().
Also add a hdlc_close() call to the uhdlc_close()
because the comment to hdlc_close() says it must be called
by the hardware driver when the HDLC device is being closed
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
Current release - regressions:
- bpf: adjust size_index according to the value of KMALLOC_MIN_SIZE
- netfilter: fix entries val in rule reset audit log
- eth: stmmac: fix incorrect rxq|txq_stats reference
Previous releases - regressions:
- ipv4: fix null-deref in ipv4_link_failure
- netfilter:
- fix several GC related issues
- fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
- eth: team: fix null-ptr-deref when team device type is changed
- eth: i40e: fix VF VLAN offloading when port VLAN is configured
- eth: ionic: fix 16bit math issue when PAGE_SIZE >= 64KB
Previous releases - always broken:
- core: fix ETH_P_1588 flow dissector
- mptcp: fix several connection hang-up conditions
- bpf:
- avoid deadlock when using queue and stack maps from NMI
- add override check to kprobe multi link attach
- hsr: properly parse HSRv1 supervisor frames.
- eth: igc: fix infinite initialization loop with early XDP redirect
- eth: octeon_ep: fix tx dma unmap len values in SG
- eth: hns3: fix GRE checksum offload issue"
* tag 'net-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
sfc: handle error pointers returned by rhashtable_lookup_get_insert_fast()
igc: Expose tx-usecs coalesce setting to user
octeontx2-pf: Do xdp_do_flush() after redirects.
bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
net: ena: Flush XDP packets on error.
net/handshake: Fix memory leak in __sock_create() and sock_alloc_file()
net: hinic: Fix warning-hinic_set_vlan_fliter() warn: variable dereferenced before check 'hwdev'
netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
netfilter: nf_tables: fix memleak when more than 255 elements expired
netfilter: nf_tables: disable toggling dormant table state more than once
vxlan: Add missing entries to vxlan_get_size()
net: rds: Fix possible NULL-pointer dereference
team: fix null-ptr-deref when team device type is changed
net: bridge: use DEV_STATS_INC()
net: hns3: add 5ms delay before clear firmware reset irq source
net: hns3: fix fail to delete tc flower rules during reset issue
net: hns3: only enable unicast promisc when mac table full
net: hns3: fix GRE checksum offload issue
net: hns3: add cmdq check for vf periodic service task
net: stmmac: fix incorrect rxq|txq_stats reference
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull finegrained timestamp reverts from Christian Brauner:
"Earlier this week we sent a few minor fixes for the multi-grained
timestamp work in [1]. While we were polishing those up after Linus
realized that there might be a nicer way to fix them we received a
regression report in [2] that fine grained timestamps break gnulib
tests and thus possibly other tools.
The kernel will elide fine-grain timestamp updates when no one is
actively querying for them to avoid performance impacts. So a sequence
like write(f1) stat(f2) write(f2) stat(f2) write(f1) stat(f1) may
result in timestamp f1 to be older than the final f2 timestamp even
though f1 was last written too but the second write didn't update the
timestamp.
Such plotholes can lead to subtle bugs when programs compare
timestamps. For example, the nap() function in [2] will estimate that
it needs to wait one ns on a fine-grain timestamp enabled filesytem
between subsequent calls to observe a timestamp change. But in general
we don't update timestamps with more than one jiffie if we think that
no one is actively querying for fine-grain timestamps to avoid
performance impacts.
While discussing various fixes the decision was to go back to the
drawing board and ultimately to explore a solution that involves only
exposing such fine-grained timestamps to nfs internally and never to
userspace.
As there are multiple solutions discussed the honest thing to do here
is not to fix this up or disable it but to cleanly revert. The general
infrastructure will probably come back but there is no reason to keep
this code in mainline.
The general changes to timestamp handling are valid and a good cleanup
that will stay. The revert is fully bisectable"
Link: https://lore.kernel.org/all/20230918-hirte-neuzugang-4c2324e7bae3@brauner [1]
Link: https://lore.kernel.org/all/bf0524debb976627693e12ad23690094e4514303.camel@linuxfromscratch.org [2]
* tag 'v6.6-rc3.vfs.ctime.revert' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
Revert "fs: add infrastructure for multigrain timestamps"
Revert "btrfs: convert to multigrain timestamps"
Revert "ext4: switch to multigrain timestamps"
Revert "xfs: switch to multigrain timestamps"
Revert "tmpfs: add support for multigrain timestamps"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- A fix for breakpoint handling which was using get_user() while atomic
- Fix the Power10 HASHCHK handler which was using get_user() while
atomic
- A few build fixes for issues caused by recent changes
Thanks to Benjamin Gray, Christophe Leroy, Kajol Jain, and Naveen N Rao.
* tag 'powerpc-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/dexcr: Move HASHCHK trap handler
powerpc/82xx: Select FSL_SOC
powerpc: Fix build issue with LD_DEAD_CODE_DATA_ELIMINATION and FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
powerpc/watchpoints: Annotate atomic context in more places
powerpc/watchpoint: Disable pagefaults when getting user instruction
powerpc/watchpoints: Disable preemption in thread_change_pc()
powerpc/perf/hv-24x7: Update domain value check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- remove some unused functions in the Xen event channel handling
- fix a regression (introduced during the merge window) when booting as
Xen PV guest
- small cleanup removing another strncpy() instance
* tag 'for-linus-6.6a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/efi: refactor deprecated strncpy
x86/xen: allow nesting of same lazy mode
x86/xen: move paravirt lazy code
arm/xen: remove lazy mode related definitions
xen: simplify evtchn_do_upcall() call maze
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock test fixes from Mike Rapoport:
"Fix several compilation errors and warnings in memblock tests"
* tag 'fixes-2023-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock tests: fix warning ‘struct seq_file’ declared inside parameter list
memblock tests: fix warning: "__ALIGN_KERNEL" redefined
memblock tests: Fix compilation errors.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A large collection of fixes around this time.
All small and mostly trivial fixes.
- Lots of fixes for the new -Wformat-truncation warnings
- A fix in ALSA rawmidi core regression and UMP handling
- Series of Cirrus codec fixes
- ASoC Intel and Realtek codec fixes
- Usual HD- and USB-audio quirks and AMD ASoC quirks"
* tag 'sound-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (64 commits)
ALSA: hda/realtek - ALC287 Realtek I2S speaker platform support
ALSA: hda: cs35l56: Use the new RUNTIME_PM_OPS() macro
ALSA: usb-audio: scarlett_gen2: Fix another -Wformat-truncation warning
ALSA: rawmidi: Fix NULL dereference at proc read
ASoC: SOF: core: Only call sof_ops_free() on remove if the probe was successful
ASoC: SOF: Intel: MTL: Reduce the DSP init timeout
ASoC: cs42l43: Add shared IRQ flag for shutters
ASoC: imx-audmix: Fix return error with devm_clk_get()
ASoC: hdaudio.c: Add missing check for devm_kstrdup
ALSA: riptide: Fix -Wformat-truncation warning for longname string
ALSA: cs4231: Fix -Wformat-truncation warning for longname string
ALSA: ad1848: Fix -Wformat-truncation warning for longname string
ALSA: hda: generic: Check potential mixer name string truncation
ALSA: cmipci: Fix -Wformat-truncation warning
ALSA: firewire: Fix -Wformat-truncation warning for MIDI stream names
ALSA: firewire: Fix -Wformat-truncation warning for longname string
ALSA: xen: Fix -Wformat-truncation warning
ALSA: opti9x: Fix -Wformat-truncation warning
ALSA: es1688: Fix -Wformat-truncation warning
ALSA: cs4236: Fix -Wformat-truncation warning
...
|
