Age | Commit message (Collapse) | Author |
|
The LPSS PWM device on on Bay Trail and Cherry Trail devices has a set
of private registers at offset 0x800, the current lpss_device_desc for
them already sets the LPSS_SAVE_CTX flag to have these saved/restored
over device-suspend, but the current lpss_device_desc was not setting
the prv_offset field, leading to the regular device registers getting
saved/restored instead.
This is causing the PWM controller to no longer work, resulting in a black
screen, after a suspend/resume on systems where the firmware clears the
APB clock and reset bits at offset 0x804.
This commit fixes this by properly setting prv_offset to 0x800 for
the PWM devices.
Cc: stable@vger.kernel.org
Fixes: e1c748179754 ("ACPI / LPSS: Add Intel BayTrail ACPI mode PWM")
Fixes: 1bfbd8eb8a7f ("ACPI / LPSS: Add ACPI IDs for Intel Braswell")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rafael J . Wysocki <rjw@rjwysocki.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.
This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.
If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.
This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.
Note that:
1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.
2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Using the pwm-meson driver on the 32-bit SoCs causes memory corruption.
The result are some hard-to-explain errors, for example
devm_clk_register() crashes with a NULL dereference somewhere deep in
the common clock framework code. In some cases the kernel even refused
to boot when any of the PWM controllers were enabled on Meson8b.
The root cause is an incorrect memory size in the devm_kcalloc() call in
meson_pwm_probe(). The code allocates an array of meson_pwm_channel
structs, but the size given is the size of the meson_pwm struct (which
seems like a small copy-and-paste error, as meson_pwm is allocated a few
lines above).
Even with this typo the code seemed to work fine on the 64-bit GX SoCs
(maybe due to the structs having the same size in the compiled result,
but I haven't checked this further).
Fixes: 211ed630753d2f ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"We have queued a few more fixes (error handling, log replay,
softlockup) and the rest is SPDX updates that touche almost all files
so the diffstat is long"
* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Only check first key for committed tree blocks
btrfs: add SPDX header to Kconfig
btrfs: replace GPL boilerplate by SPDX -- sources
btrfs: replace GPL boilerplate by SPDX -- headers
Btrfs: fix loss of prealloc extents past i_size after fsync log replay
Btrfs: clean up resources during umount after trans is aborted
btrfs: Fix possible softlock on single core machines
Btrfs: bail out on error during replay_dir_deletes
Btrfs: fix NULL pointer dereference in log_dir_items
|
|
Pull cifs fixes from Steve French:
"SMB3 fixes, a few for stable, and some important cleanup work from
Ronnie of the smb3 transport code"
* tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: change validate_buf to validate_iov
cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data()
cifs: Change SMB2_open to return an iov for the error parameter
cifs: add resp_buf_size to the mid_q_entry structure
smb3.11: replace a 4 with server->vals->header_preamble_size
cifs: replace a 4 with server->vals->header_preamble_size
cifs: add pdu_size to the TCP_Server_Info structure
SMB311: Improve checking of negotiate security contexts
SMB3: Fix length checking of SMB3.11 negotiate request
CIFS: add ONCE flag for cifs_dbg type
cifs: Use ULL suffix for 64-bit constant
SMB3: Log at least once if tree connect fails during reconnect
cifs: smb2pdu: Fix potential NULL pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
The status handling code is actually a running regression from the
previous merge window which had an incomplete fix (now reverted) and
most of the remaining bug fixes are for problems older than the
current merge window"
[ Side note: this merge also takes the base kernel git repository to 6+
million objects for the first time. Technically we hit it a couple of
merges ago already if you count all the tag objects, but now it
reaches 6M+ objects reachable from HEAD.
I was joking around that that's when I should switch to 5.0, because
3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
probably not, even if numerology is about as good a reason as any.
- Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
scsi: aacraid: Insure command thread is not recursively stopped
scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
scsi: qla2xxx: correctly shift host byte
scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
scsi: qla2xxx: Avoid double completion of abort command
scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
scsi: scsi_dh: Don't look for NULL devices handlers by name
scsi: core: remove redundant assignment to shost->use_blk_mq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by flex,
bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by flex,
bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: extend output of 'listnewconfig'
kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
Kbuild: fix # escaping in .cmd files for future Make
kbuild: deb-pkg: split generating packaging and build
kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
kbuild: rename *-asn1.[ch] to *.asn1.[ch]
kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
.gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
kbuild: add %.dtb.S and %.dtb to 'targets' automatically
kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
genksyms: generate lexer and parser during build instead of shipping
kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
.gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
kbuild: use HOSTLDFLAGS for single .c executables
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes and updates for x86:
- Address a swiotlb regression which was caused by the recent DMA
rework and made driver fail because dma_direct_supported() returned
false
- Fix a signedness bug in the APIC ID validation which caused invalid
APIC IDs to be detected as valid thereby bloating the CPU possible
space.
- Fix inconsisten config dependcy/select magic for the MFD_CS5535
driver.
- Fix a corruption of the physical address space bits when encryption
has reduced the address space and late cpuinfo updates overwrite
the reduced bit information with the original value.
- Dominiks syscall rework which consolidates the architecture
specific syscall functions so all syscalls can be wrapped with the
same macros. This allows to switch x86/64 to struct pt_regs based
syscalls. Extend the clearing of user space controlled registers in
the entry patch to the lower registers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix signedness bug in APIC ID validity checks
x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
x86/olpc: Fix inconsistent MFD_CS5535 configuration
swiotlb: Use dma_direct_supported() for swiotlb_ops
syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
syscalls/core, syscalls/x86: Clean up syscall stub naming convention
syscalls/x86: Extend register clearing on syscall entry to lower registers
syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
x86/syscalls: Don't pointlessly reload the system call number
x86/mm: Fix documentation of module mapping range with 4-level paging
x86/cpuid: Switch to 'static const' specifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 pti updates from Thomas Gleixner:
"Another series of PTI related changes:
- Remove the manual stack switch for user entries from the idtentry
code. This debloats entry by 5k+ bytes of text.
- Use the proper types for the asm/bootparam.h defines to prevent
user space compile errors.
- Use PAGE_GLOBAL for !PCID systems to gain back performance
- Prevent setting of huge PUD/PMD entries when the entries are not
leaf entries otherwise the entries to which the PUD/PMD points to
and are populated get lost"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
x86/pti: Leave kernel text global for !PCID
x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
x86/pti: Enable global pages for shared areas
x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
x86/mm: Comment _PAGE_GLOBAL mystery
x86/mm: Remove extra filtering in pageattr code
x86/mm: Do not auto-massage page protections
x86/espfix: Document use of _PAGE_GLOBAL
x86/mm: Introduce "default" kernel PTE mask
x86/mm: Undo double _PAGE_PSE clearing
x86/mm: Factor out pageattr _PAGE_GLOBAL setting
x86/entry/64: Drop idtentry's manual stack switch for user entries
x86/uapi: Fix asm/bootparam.h userspace compilation errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"A few scheduler fixes:
- Prevent a bogus warning vs. runqueue clock update flags in
do_sched_rt_period_timer()
- Simplify the helper functions which handle requests for skipping
the runqueue clock updat.
- Do not unlock the tunables mutex in the error path of the cpu
frequency scheduler utils. Its not held.
- Enforce proper alignement for 'struct util_est' in sched_avg to
prevent a misalignment fault on IA64"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Force proper alignment of 'struct util_est'
sched/core: Simplify helpers for rq clock update skip requests
sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning
sched/cpufreq/schedutil: Fix error path mutex unlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more perf updates from Thomas Gleixner:
"A rather large set of perf updates:
Kernel:
- Fix various initialization issues
- Prevent creating [ku]probes for not CAP_SYS_ADMIN users
Tooling:
- Show only failing syscalls with 'perf trace --failure' (Arnaldo
Carvalho de Melo)
e.g: See what 'openat' syscalls are failing:
# perf trace --failure -e openat
762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory
<SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? >
790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory
^C#
- Show information about the event (freq, nr_samples, total
period/nr_events) in the annotate --tui and --stdio2 'perf
annotate' output, similar to the first line in the 'perf report
--tui', but just for the samples for a the annotated symbol
(Arnaldo Carvalho de Melo)
- Introduce 'perf version --build-options' to show what features were
linked, aliased as well as a shorter 'perf -vv' (Jin Yao)
- Add a "dso_size" sort order (Kim Phillips)
- Remove redundant ')' in the tracepoint output in 'perf trace'
(Changbin Du)
- Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo
Carvalho de Melo)
- Show group details on the title line in the annotate browser and
'perf annotate --stdio2' output, so that the per-event columns can
have headers (Arnaldo Carvalho de Melo)
- Fixup vertical line separating metrics from instructions and
cleaning unused lines at the bottom, both in the annotate TUI
browser (Arnaldo Carvalho de Melo)
- Remove duplicated 'samples' in lost samples warning in
'perf report' (Arnaldo Carvalho de Melo)
- Synchronize i915_drm.h, silencing the perf build process,
automagically adding support for the new DRM_I915_QUERY ioctl
(Arnaldo Carvalho de Melo)
- Make auxtrace_queues__add_buffer() allocate struct buffer, from a
patchkit already applied (Adrian Hunter)
- Fix the --stdio2/TUI annotate output to include group details, be
it for a recorded '{a,b,f}' explicit event group or when forcing
group display using 'perf report --group' for a set of events not
recorded as a group (Arnaldo Carvalho de Melo)
- Fix display artifacts in the ui browser (base class for the
annotate and main report/top TUI browser) related to the extra
title lines work (Arnaldo Carvalho de Melo)
- perf auxtrace refactorings, leftovers from a previously partially
processed patchset (Adrian Hunter)
- Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de
Melo)
- Synchronize i915_drm.h, silencing a perf build warning and in the
process automagically adding support for a new ioctl command
(Arnaldo Carvalho de Melo)
- Fix a strncpy issue in uprobe tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
tracing/uprobe_event: Fix strncpy corner case
perf/core: Fix perf_uprobe_init()
perf/core: Fix perf_kprobe_init()
perf/core: Fix use-after-free in uprobe_perf_close()
perf tests clang: Fix function name for clang IR test
perf clang: Add support for recent clang versions
perf tools: Fix perf builds with clang support
perf tools: No need to include namespaces.h in util.h
perf hists browser: Remove leftover from row returned from refresh
perf hists browser: Show extra_title_lines in the 'D' debug hotkey
perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering
tools headers uapi: Synchronize i915_drm.h
perf report: Remove duplicated 'samples' in lost samples warning
perf ui browser: Fixup cleaning unused lines at the bottom
perf annotate browser: Fixup vertical line separating metrics from instructions
perf annotate: Show group details on the title line
perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer
perf/x86/intel: Move regs->flags EXACT bit init
perf trace: Remove redundant ')'
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI bootup fixlet from Thomas Gleixner:
"A single fix for an early boot warning caused by invoking
this_cpu_has() before SMP initialization"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix bogus warning during EFI bootup, use boot_cpu_has() instead of this_cpu_has() in build_cr3_noflush()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq affinity fixes from Thomas Gleixner:
- Fix error path handling in the affinity spreading code
- Make affinity spreading smarter to avoid issues on systems which
claim to have hotpluggable CPUs while in fact they can't hotplug
anything.
So instead of trying to spread the vectors (and thereby the
associated device queues) to all possibe CPUs, spread them on all
present CPUs first. If there are left over vectors after that first
step they are spread among the possible, but not present CPUs which
keeps the code backwards compatible for virtual decives and NVME
which allocate a queue per possible CPU, but makes the spreading
smarter for devices which have less queues than possible or present
CPUs.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Spread irq vectors among present CPUs as far as possible
genirq/affinity: Allow irq spreading from a given starting point
genirq/affinity: Move actual irq vector spreading into a helper function
genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask
genirq/affinity: Don't return with empty affinity masks on error
|
|
Pull OpenRISC fixlet from Stafford Horne:
"Just one small thing here, it came in a while back but I didnt have
anything in my 4.16 queue, still its the only thing for 4.17 so
sending it alone.
Small cleanup: remove unused __ARCH_HAVE_MMU define"
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: remove unused __ARCH_HAVE_MMU define
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes when loading modules built with a different
CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error
conditions from firmware.
- Remove tlbie trace points from KVM code that's called in real mode,
because it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is
actually the minimal set when we build with support for firmware
supplied CPU features.
Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
* tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features
powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode
powerpc/8xx: Fix build with hugetlbfs enabled
powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops
powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops
powerpc/fscr: Enable interrupts earlier before calling get_user()
powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()
powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic
|
|
Merge yet more updates from Andrew Morton:
- various hotfixes
- kexec_file updates and feature work
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
kernel/kexec_file.c: move purgatories sha256 to common code
kernel/kexec_file.c: allow archs to set purgatory load address
kernel/kexec_file.c: remove mis-use of sh_offset field during purgatory load
kernel/kexec_file.c: remove unneeded variables in kexec_purgatory_setup_sechdrs
kernel/kexec_file.c: remove unneeded for-loop in kexec_purgatory_setup_sechdrs
kernel/kexec_file.c: split up __kexec_load_puragory
kernel/kexec_file.c: use read-only sections in arch_kexec_apply_relocations*
kernel/kexec_file.c: search symbols in read-only kexec_purgatory
kernel/kexec_file.c: make purgatory_info->ehdr const
kernel/kexec_file.c: remove checks in kexec_purgatory_load
include/linux/kexec.h: silence compile warnings
kexec_file, x86: move re-factored code to generic side
x86: kexec_file: clean up prepare_elf64_headers()
x86: kexec_file: lift CRASH_MAX_RANGES limit on crash_mem buffer
x86: kexec_file: remove X86_64 dependency from prepare_elf64_headers()
x86: kexec_file: purge system-ram walking from prepare_elf64_headers()
kexec_file,x86,powerpc: factor out kexec_file_ops functions
kexec_file: make use of purgatory optional
proc: revalidate misc dentries
mm, slab: reschedule cache_reap() on the same CPU
...
|
|
The code to verify the new kernels sha digest is applicable for all
architectures. Move it to common code.
One problem is the string.c implementation on x86. Currently sha256
includes x86/boot/string.h which defines memcpy and memset to be gcc
builtins. By moving the sha256 implementation to common code and
changing the include to linux/string.h both functions are no longer
defined. Thus definitions have to be provided in x86/purgatory/string.c
Link: http://lkml.kernel.org/r/20180321112751.22196-12-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For s390 new kernels are loaded to fixed addresses in memory before they
are booted. With the current code this is a problem as it assumes the
kernel will be loaded to an 'arbitrary' address. In particular,
kexec_locate_mem_hole searches for a large enough memory region and sets
the load address (kexec_bufer->mem) to it.
Luckily there is a simple workaround for this problem. By returning 1
in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off. This
allows the architecture to set kbuf->mem by hand. While the trick works
fine for the kernel it does not for the purgatory as here the
architectures don't have access to its kexec_buffer.
Give architectures access to the purgatories kexec_buffer by changing
kexec_load_purgatory to take a pointer to it. With this change
architectures have access to the buffer and can edit it as they need.
A nice side effect of this change is that we can get rid of the
purgatory_info->purgatory_load_address field. As now the information
stored there can directly be accessed from kbuf->mem.
Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current code uses the sh_offset field in purgatory_info->sechdrs to
store a pointer to the current load address of the section. Depending
whether the section will be loaded or not this is either a pointer into
purgatory_info->purgatory_buf or kexec_purgatory. This is not only a
violation of the ELF standard but also makes the code very hard to
understand as you cannot tell if the memory you are using is read-only
or not.
Remove this misuse and store the offset of the section in
pugaroty_info->purgatory_buf in sh_offset.
Link: http://lkml.kernel.org/r/20180321112751.22196-10-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The main loop currently uses quite a lot of variables to update the
section headers. Some of them are unnecessary. So clean them up a
little.
Link: http://lkml.kernel.org/r/20180321112751.22196-9-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To update the entry point there is an extra loop over all section
headers although this can be done in the main loop. So move it there
and eliminate the extra loop and variable to store the 'entry section
index'.
Also, in the main loop, move the usual case, i.e. non-bss section, out
of the extra if-block.
Link: http://lkml.kernel.org/r/20180321112751.22196-8-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When inspecting __kexec_load_purgatory you find that it has two tasks
1) setting up the kexec_buffer for the new kernel and,
2) setting up pi->sechdrs for the final load address.
The two tasks are independent of each other. To improve readability
split up __kexec_load_purgatory into two functions, one for each task,
and call them directly from kexec_load_purgatory.
Link: http://lkml.kernel.org/r/20180321112751.22196-7-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the relocations are applied to the purgatory only the section the
relocations are applied to is writable. The other sections, i.e. the
symtab and .rel/.rela, are in read-only kexec_purgatory. Highlight this
by marking the corresponding variables as 'const'.
While at it also change the signatures of arch_kexec_apply_relocations* to
take section pointers instead of just the index of the relocation section.
This removes the second lookup and sanity check of the sections in arch
code.
Link: http://lkml.kernel.org/r/20180321112751.22196-6-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The stripped purgatory does not contain a symtab. So when looking for
symbols this is done in read-only kexec_purgatory. Highlight this by
marking the corresponding variables as 'const'.
Link: http://lkml.kernel.org/r/20180321112751.22196-5-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The kexec_purgatory buffer is read-only. Thus all pointers into
kexec_purgatory are read-only, too. Point this out by explicitly
marking purgatory_info->ehdr as 'const' and update the comments in
purgatory_info.
Link: http://lkml.kernel.org/r/20180321112751.22196-4-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before the purgatory is loaded several checks are done whether the ELF
file in kexec_purgatory is valid or not. These checks are incomplete.
For example they don't check for the total size of the sections defined
in the section header table or if the entry point actually points into
the purgatory.
On the other hand the purgatory, although an ELF file on its own, is
part of the kernel. Thus not trusting the purgatory means not trusting
the kernel build itself.
So remove all validity checks on the purgatory and just trust the kernel
build.
Link: http://lkml.kernel.org/r/20180321112751.22196-3-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "kexec_file: Clean up purgatory load", v2.
Following the discussion with Dave and AKASHI, here are the common code
patches extracted from my recent patch set (Add kexec_file_load support
to s390) [1]. The patches were extracted to allow upstream integration
together with AKASHI's common code patches before the arch code gets
adjusted to the new base.
The reason for this series is to prepare common code for adding
kexec_file_load to s390 as well as cleaning up the mis-use of the
sh_offset field during purgatory load. In detail this series contains:
Patch #1&2: Minor cleanups/fixes.
Patch #3-9: Clean up the purgatory load/relocation code. Especially
remove the mis-use of the purgatory_info->sechdrs->sh_offset field,
currently holding a pointer into either kexec_purgatory (ro) or
purgatory_buf (rw) depending on the section. With these patches the
section address will be calculated verbosely and sh_offset will contain
the offset of the section in the stripped purgatory binary
(purgatory_buf).
Patch #10: Allows architectures to set the purgatory load address. This
patch is important for s390 as the kernel and purgatory have to be
loaded to fixed addresses. In current code this is impossible as the
purgatory load is opaque to the architecture.
Patch #11: Moves x86 purgatories sha implementation to common lib/
directory to allow reuse in other architectures.
This patch (of 11)
When building the kernel with CONFIG_KEXEC_FILE enabled gcc prints a
compile warning multiple times.
In file included from <path>/linux/init/initramfs.c:526:0:
<path>/include/linux/kexec.h:120:9: warning: `struct kimage' declared inside parameter list [enabled by default]
unsigned long cmdline_len);
^
This is because the typedefs for kexec_file_load uses struct kimage
before it is declared. Fix this by simply forward declaring struct
kimage.
Link: http://lkml.kernel.org/r/20180321112751.22196-2-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the previous patches, commonly-used routines, exclude_mem_range() and
prepare_elf64_headers(), were carved out. Now place them in kexec
common code. A prefix "crash_" is given to each of their names to avoid
possible name collisions.
Link: http://lkml.kernel.org/r/20180306102303.9063-8-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Removing bufp variable in prepare_elf64_headers() makes the code simpler
and more understandable.
Link: http://lkml.kernel.org/r/20180306102303.9063-7-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While CRASH_MAX_RANGES (== 16) seems to be good enough, fixed-number
array is not a good idea in general.
In this patch, size of crash_mem buffer is calculated as before and the
buffer is now dynamically allocated. This change also allows removing
crash_elf_data structure.
Link: http://lkml.kernel.org/r/20180306102303.9063-6-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code guarded by CONFIG_X86_64 is necessary on some architectures
which have a dedicated kernel mapping outside of linear memory mapping.
(arm64 is among those.)
In this patch, an additional argument, kernel_map, is added to enable/
disable the code removing #ifdef.
Link: http://lkml.kernel.org/r/20180306102303.9063-5-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While prepare_elf64_headers() in x86 looks pretty generic for other
architectures' use, it contains some code which tries to list crash
memory regions by walking through system resources, which is not always
architecture agnostic. To make this function more generic, the related
code should be purged.
In this patch, prepare_elf64_headers() simply scans crash_mem buffer
passed and add all the listed regions to elf header as a PT_LOAD
segment. So walk_system_ram_res(prepare_elf64_headers_callback) have
been moved forward before prepare_elf64_headers() where the callback,
prepare_elf64_headers_callback(), is now responsible for filling up
crash_mem buffer.
Meanwhile exclude_elf_header_ranges() used to be called every time in
this callback it is rather redundant and now called only once in
prepare_elf_headers() as well.
Link: http://lkml.kernel.org/r/20180306102303.9063-4-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As arch_kexec_kernel_image_{probe,load}(),
arch_kimage_file_post_load_cleanup() and arch_kexec_kernel_verify_sig()
are almost duplicated among architectures, they can be commonalized with
an architecture-defined kexec_file_ops array. So let's factor them out.
Link: http://lkml.kernel.org/r/20180306102303.9063-3-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "kexec_file, x86, powerpc: refactoring for other
architecutres", v2.
This is a preparatory patchset for adding kexec_file support on arm64.
It was originally included in a arm64 patch set[1], but Philipp is also
working on their kexec_file support on s390[2] and some changes are now
conflicting.
So these common parts were extracted and put into a separate patch set
for better integration. What's more, my original patch#4 was split into
a few small chunks for easier review after Dave's comment.
As such, the resulting code is basically identical with my original, and
the only *visible* differences are:
- renaming of _kexec_kernel_image_probe() and _kimage_file_post_load_cleanup()
- change one of types of arguments at prepare_elf64_headers()
Those, unfortunately, require a couple of trivial changes on the rest
(#1, #6 to #13) of my arm64 kexec_file patch set[1].
Patch #1 allows making a use of purgatory optional, particularly useful
for arm64.
Patch #2 commonalizes arch_kexec_kernel_{image_probe, image_load,
verify_sig}() and arch_kimage_file_post_load_cleanup() across
architectures.
Patches #3-#7 are also intended to generalize parse_elf64_headers(),
along with exclude_mem_range(), to be made best re-use of.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-February/561182.html
[2] http://lkml.iu.edu//hypermail/linux/kernel/1802.1/02596.html
This patch (of 7):
On arm64, crash dump kernel's usable memory is protected by *unmapping*
it from kernel virtual space unlike other architectures where the region
is just made read-only. It is highly unlikely that the region is
accidentally corrupted and this observation rationalizes that digest
check code can also be dropped from purgatory. The resulting code is so
simple as it doesn't require a bit ugly re-linking/relocation stuff,
i.e. arch_kexec_apply_relocations_add().
Please see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2017-December/545428.html
All that the purgatory does is to shuffle arguments and jump into a new
kernel, while we still need to have some space for a hash value
(purgatory_sha256_digest) which is never checked against.
As such, it doesn't make sense to have trampline code between old kernel
and new kernel on arm64.
This patch introduces a new configuration, ARCH_HAS_KEXEC_PURGATORY, and
allows related code to be compiled in only if necessary.
[takahiro.akashi@linaro.org: fix trivial screwup]
Link: http://lkml.kernel.org/r/20180309093346.GF25863@linaro.org
Link: http://lkml.kernel.org/r/20180306102303.9063-2-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If module removes proc directory while another process pins it by
chdir'ing to it, then subsequent recreation of proc entry and all
entries down the tree will not be visible to any process until pinning
process unchdir from directory and unpins everything.
Steps to reproduce:
proc_mkdir("aaa", NULL);
proc_create("aaa/bbb", ...);
chdir("/proc/aaa");
remove_proc_entry("aaa/bbb", NULL);
remove_proc_entry("aaa", NULL);
proc_mkdir("aaa", NULL);
# inaccessible because "aaa" dentry still points
# to the original "aaa".
proc_create("aaa/bbb", ...);
Fix is to implement ->d_revalidate and ->d_delete.
Link: http://lkml.kernel.org/r/20180312201938.GA4871@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cache_reap() is initially scheduled in start_cpu_timer() via
schedule_delayed_work_on(). But then the next iterations are scheduled
via schedule_delayed_work(), i.e. using WORK_CPU_UNBOUND.
Thus since commit ef557180447f ("workqueue: schedule WORK_CPU_UNBOUND
work on wq_unbound_cpumask CPUs") there is no guarantee the future
iterations will run on the originally intended cpu, although it's still
preferred. I was able to demonstrate this with
/sys/module/workqueue/parameters/debug_force_rr_cpu. IIUC, it may also
happen due to migrating timers in nohz context. As a result, some cpu's
would be calling cache_reap() more frequently and others never.
This patch uses schedule_delayed_work_on() with the current cpu when
scheduling the next iteration.
Link: http://lkml.kernel.org/r/20180411070007.32225-1-vbabka@suse.cz
Fixes: ef557180447f ("workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 6326fec1122c ("mm: Use owner_priv bit for PageSwapCache,
valid when PageSwapBacked"), PG_swapcache is an alias for
PG_owner_priv_1, which may be also used for other purposes.
To know whether the bit indeed has the PG_swapcache meaning, it is
necessary to check PG_swapbacked, hence this bit must be exported.
Link: http://lkml.kernel.org/r/20180410161345.142e142d@ezekiel.suse.cz
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: "Marc-Andr Lureau" <marcandre.lureau@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
syzbot reported a use-after-free of shm_file_data(file)->file->f_op in
shm_get_unmapped_area(), called via sys_remap_file_pages().
Unfortunately it couldn't generate a reproducer, but I found a bug which
I think caused it. When remap_file_pages() is passed a full System V
shared memory segment, the memory is first unmapped, then a new map is
created using the ->vm_file. Between these steps, the shm ID can be
removed and reused for a new shm segment. But, shm_mmap() only checks
whether the ID is currently valid before calling the underlying file's
->mmap(); it doesn't check whether it was reused. Thus it can use the
wrong underlying file, one that was already freed.
Fix this by making the "outer" shm file (the one that gets put in
->vm_file) hold a reference to the real shm file, and by making
__shm_open() require that the file associated with the shm ID matches
the one associated with the "outer" file.
Taking the reference to the real shm file is needed to fully solve the
problem, since otherwise sfd->file could point to a freed file, which
then could be reallocated for the reused shm ID, causing the wrong shm
segment to be mapped (and without the required permission checks).
Commit 1ac0b6dec656 ("ipc/shm: handle removed segments gracefully in
shm_mmap()") almost fixed this bug, but it didn't go far enough because
it didn't consider the case where the shm ID is reused.
The following program usually reproduces this bug:
#include <stdlib.h>
#include <sys/shm.h>
#include <sys/syscall.h>
#include <unistd.h>
int main()
{
int is_parent = (fork() != 0);
srand(getpid());
for (;;) {
int id = shmget(0xF00F, 4096, IPC_CREAT|0700);
if (is_parent) {
void *addr = shmat(id, NULL, 0);
usleep(rand() % 50);
while (!syscall(__NR_remap_file_pages, addr, 4096, 0, 0, 0));
} else {
usleep(rand() % 50);
shmctl(id, IPC_RMID, NULL);
}
}
}
It causes the following NULL pointer dereference due to a 'struct file'
being used while it's being freed. (I couldn't actually get a KASAN
use-after-free splat like in the syzbot report. But I think it's
possible with this bug; it would just take a more extraordinary race...)
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 9 PID: 258 Comm: syz_ipc Not tainted 4.16.0-05140-gf8cf2f16a7c95 #189
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
RIP: 0010:d_inode include/linux/dcache.h:519 [inline]
RIP: 0010:touch_atime+0x25/0xd0 fs/inode.c:1724
[...]
Call Trace:
file_accessed include/linux/fs.h:2063 [inline]
shmem_mmap+0x25/0x40 mm/shmem.c:2149
call_mmap include/linux/fs.h:1789 [inline]
shm_mmap+0x34/0x80 ipc/shm.c:465
call_mmap include/linux/fs.h:1789 [inline]
mmap_region+0x309/0x5b0 mm/mmap.c:1712
do_mmap+0x294/0x4a0 mm/mmap.c:1483
do_mmap_pgoff include/linux/mm.h:2235 [inline]
SYSC_remap_file_pages mm/mmap.c:2853 [inline]
SyS_remap_file_pages+0x232/0x310 mm/mmap.c:2769
do_syscall_64+0x64/0x1a0 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ebiggers@google.com: add comment]
Link: http://lkml.kernel.org/r/20180410192850.235835-1-ebiggers3@gmail.com
Link: http://lkml.kernel.org/r/20180409043039.28915-1-ebiggers3@gmail.com
Reported-by: syzbot+d11f321e7f1923157eac80aa990b446596f46439@syzkaller.appspotmail.com
Fixes: c8d78c1823f4 ("mm: replace remap_file_pages() syscall with emulation")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Building orangefs on MMU-less machines now results in a link error
because of the newly introduced use of the filemap_page_mkwrite()
function:
ERROR: "filemap_page_mkwrite" [fs/orangefs/orangefs.ko] undefined!
This adds a dummy version for it, similar to the existing
generic_file_mmap and generic_file_readonly_mmap stubs in the same file,
to avoid the link error without adding #ifdefs in each file system that
uses these.
Link: http://lkml.kernel.org/r/20180409105555.2439976-1-arnd@arndb.de
Fixes: a5135eeab2e5 ("orangefs: implement vm_ops->fault")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Brandenburg <martin@omnibond.com>
Cc: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__get_user_pages_fast handles errors differently from
get_user_pages_fast: the former always returns the number of pages
pinned, the later might return a negative error code.
Link: http://lkml.kernel.org/r/1522962072-182137-6-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
get_user_pages_fast is supposed to be a faster drop-in equivalent of
get_user_pages. As such, callers expect it to return a negative return
code when passed an invalid address, and never expect it to return 0
when passed a positive number of pages, since its documentation says:
* Returns number of pages pinned. This may be fewer than the number
* requested. If nr_pages is 0 or negative, returns 0. If no pages
* were pinned, returns -errno.
When get_user_pages_fast fall back on get_user_pages this is exactly
what happens. Unfortunately the implementation is inconsistent: it
returns 0 if passed a kernel address, confusing callers: for example,
the following is pretty common but does not appear to do the right thing
with a kernel address:
ret = get_user_pages_fast(addr, 1, writeable, &page);
if (ret < 0)
return ret;
Change get_user_pages_fast to return -EFAULT when supplied a kernel
address to make it match expectations.
All callers have been audited for consistency with the documented
semantics.
Link: http://lkml.kernel.org/r/1522962072-182137-4-git-send-email-mst@redhat.com
Fixes: 5b65c4677a57 ("mm, x86/mm: Fix performance regression in get_user_pages_fast()")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm/get_user_pages_fast fixes, cleanups", v2.
Turns out get_user_pages_fast and __get_user_pages_fast return different
values on error when given a single page: __get_user_pages_fast returns
0. get_user_pages_fast returns either 0 or an error.
Callers of get_user_pages_fast expect an error so fix it up to return an
error consistently.
Stress the difference between get_user_pages_fast and
__get_user_pages_fast to make sure callers aren't confused.
This patch (of 3):
__gup_benchmark_ioctl does not handle the case where get_user_pages_fast
fails:
- a negative return code will cause a buffer overrun
- returning with partial success will cause use of uninitialized
memory.
[akpm@linux-foundation.org: simplification]
Link: http://lkml.kernel.org/r/1522962072-182137-3-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We've got a bug report indicating a kernel panic at booting on an x86-32
system, and it turned out to be the invalid PCI resource assigned after
reallocation. __find_resource() first aligns the resource start address
and resets the end address with start+size-1 accordingly, then checks
whether it's contained. Here the end address may overflow the integer,
although resource_contains() still returns true because the function
validates only start and end address. So this ends up with returning an
invalid resource (start > end).
There was already an attempt to cover such a problem in the commit
47ea91b4052d ("Resource: fix wrong resource window calculation"), but
this case is an overseen one.
This patch adds the validity check of the newly calculated resource for
avoiding the integer overflow problem.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1086739
Link: http://lkml.kernel.org/r/s5hpo37d5l8.wl-tiwai@suse.de
Fixes: 23c570a67448 ("resource: ability to resize an allocated resource")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Michael Henders <hendersm@shaw.ca>
Tested-by: Michael Henders <hendersm@shaw.ca>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"In addition to bug fixes and cleanups there are two new features from
Amir:
- Consistent inode number support for the case when layers are not
all on the same filesystem (feature is dubbed "xino").
- Optimize overlayfs file handle decoding. This one touches the
exportfs interface to allow detecting the disconnected directory
case"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: update documentation w.r.t "xino" feature
ovl: add support for "xino" mount and config options
ovl: consistent d_ino for non-samefs with xino
ovl: consistent i_ino for non-samefs with xino
ovl: constant st_ino for non-samefs with xino
ovl: allocate anon bdev per unique lower fs
ovl: factor out ovl_map_dev_ino() helper
ovl: cleanup ovl_update_time()
ovl: add WARN_ON() for non-dir redirect cases
ovl: cleanup setting OVL_INDEX
ovl: set d->is_dir and d->opaque for last path element
ovl: Do not check for redirect if this is last layer
ovl: lookup in inode cache first when decoding lower file handle
ovl: do not try to reconnect a disconnected origin dentry
ovl: disambiguate ovl_encode_fh()
ovl: set lower layer st_dev only if setting lower st_ino
ovl: fix lookup with middle layer opaque dir and absolute path redirects
ovl: Set d->last properly during lookup
ovl: set i_ino to the value of st_ino for NFS export
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management update from Zhang Rui:
- Fix race condition in imx_thermal_probe() (Mikhail Lappo)
- Add cooling device's statistics in sysfs (Viresh Kumar)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add cooling device's statistics in sysfs
thermal: imx: Fix race condition in imx_thermal_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi updates from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi_scan: Use lowercase letters for UUID
firmware: dmi_scan: Add DMI_OEM_STRING support to dmi_matches
firmware: dmi_scan: Fix UUID length safety check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
|