summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-10-23Merge tag 'at91-ab-dt2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt Merge "Second batch of DT changes for 4.4" from Alexandre Belloni: - some DT fixes: pullups, disabled property - the PMC is now a syscon - great improvement of sama5d2 support * tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: ARM: at91/dt: sama5d2: add missing devices ARM: at91/dt: sama5d4: add the macb1 node ARM: at91/dt: add pullup on mmc2 data signals ARM: at91/dt: sama5d2_xplained: add regulator nodes ARM: at91/dt: fix "disabled" property on at91rm9200 ARM: at91/dt: use syscon for PMC
2015-10-23Merge tag 'omap-for-v4.4/dt-pt2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Merge "omap dts changes for v4.4 merge window, part 2" from Tony Lindgren: Few more omap dts changes for v4.4 merge window, mostly to fix and clean up some omap5 issues to allow adding other omap5 boards. Also some other fixes and clean-up: - Fix SDIO WLAN for omap5 that's been broken for a while. As further patches are still needed for wl18xx, no need for stable on this one. - Move most of omap5 support into omap5-board-common.dtsi as most omap5 boards seem to share the same basic set of devices. - Add minimal IGEPv5 support using based on omap5-board-common.dtsi - Remove now unneedes gpio hogging for dra72-evm - Update Javier Martinez Canillas email address - Change earlier IGEP boards to use IOPAD pinmux macros * tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am335x-base0033: Use IOPAD pinmux macro ARM: dts: am335x-igep0033: Use IOPAD pinmux macro ARM: dts: omap3-igep0020: Use IOPAD pinmux macro ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts ARM: dts: Update Javier Martinez Canillas's email ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios ARM: dts: Add basic support for isee igepv5 ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi ARM: dts: Fix WLAN regression on omap5-uevm
2015-10-23ARM: dts: uniphier: add ProXstream2 Vodka board supportMasahiro Yamada
Initial version of DTS for ProXstream2 Vodka board. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-10-23ARM: dts: uniphier: add ProXstream2 Gentil board supportMasahiro Yamada
Initial version of DTS for ProXstream2 Gentil board. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-10-23ARM: dts: uniphier: use stdout-path instead of consoleMasahiro Yamada
Specifying both console and stdout-path is redundant. Add options ":115200n8" to stdout-path and drop "console=ttyS0,115200". Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-10-23Merge tag 'sti-dt-for-v4.4-2' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt Merge "STi DT changes for v4.4, round 2" from Maxime Coquelin: - Use STiH418's A9 PLL - Add Ethernet support to STiH407 family * tag 'sti-dt-for-v4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti: ARM: STi: DT: Add support for stih418 A9 pll ARM: dts: Enable Ethernet on STi's B2199 board ARM: dts: Enable Ethernet on STi's B2120 boards ARM: dts: Add Ethernet node to STiH407 family ARM: dts: Fix RGMII pinctrl timings
2015-10-23ARM: dts: WM8750: fix cpu compatible valueVladimir Zapolskiy
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-10-23ARM: dts: TI-Nspire: fix cpu compatible valueVladimir Zapolskiy
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-10-23Merge tag 'imx-dt-4.4' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt The i.MX device tree changes for 4.4: - Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D. - Add a few low power mode related devices and touch controller for i.MX6UL. - Add a number of devices for i.MX7D SDB board support, USB, Dual FEC, and eMMC5.0. - i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya LCD, touch and wifi support, add new boards Nitrogen6_Lite and Nitrogen6_Max. - Enable touch screen and NAND Flash controller for a few Vybrid devices. - Some random and small updates on LS1021A and MXS support. * tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits) ARM: dts: ls1021a: Add quirk for Erratum A009116 ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names" ARM: dts: imx6: change the core clock of spdif ARM: dts: vf-colibri: enable NAND flash controller ARM: dts: vf610twr: add NAND flash controller peripherial ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board ARM: dts: imx: add Boundary Devices Nitrogen6_Max board ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices of: Add Boundary Devices Inc. vendor prefix ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11 ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11 ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support ARM: dts: imx6dql-nitrogen6x: add touchscreen support ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel ARM: dts: vf500-colibri: Add device tree node for touchscreen support ARM: dts: i.MX35: fix cpu compatible value ARM: dts: i.MX31: fix cpu compatible value ... Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-23Merge tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek into next/dtOlof Johansson
Delete regulator-compatible usage in mt8135-evbp1.dts. The regualtor-compatible binding is deprecated, instead the node name is used. Mediatek timer driver supports as well mt8127, mt8135 and mt8173. Add these SOCs to the bindings list. Power domains venc and venc_lt need clocks two extra clocks to access their registers. We update the bindings documentation about this. Update SMP bindings documentation by adding support for mt6589 and mt81xx SOCs. Update mt8127.dtsi and mt8135.dtsi to enable SMP support. * tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek: ARM: dts: mt8127: enable basic SMP bringup for mt8127 ARM: dts: mt8135: enable basic SMP bringup for mt8135 devicetree: bindings: add new SMP enable method Mediatek SoC dt-bindings: soc: Add clocks for Mediatek SCPSYS unit dt-bindings: add more MediaTek SoC to mtk-timer binding ARM: dts: mt8135-evbp1: remove regulator-compatible usage Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-23Merge tag 'v4.4-rockchip-dts32-2' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt SPDIF device nodes for the newly added driver. * tag 'v4.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock2 Square ARM: dts: rockchip: Add SPDIF transceiver for RK3288 ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock ARM: dts: rockchip: Add SPDIF transceiver for RK3188 Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-23Merge tag 'sunxi-dt-for-4.4-2' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt Allwinner DT changes for 4.4, round 2 More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi M2, pcduino2), further consolidation for the q8-based designs and a bunch of random patches enhancing support for existing boards * tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits) ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80 ARM: dts: sun8i: Add NMI interrupt controller node ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus" ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano ARM: dts: sun6i: Turn on gmac on Colombus ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi ARM: dts: sunxi: Enable PWM controller on Q8 format tablets ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s ARM: dts: sun5i: Add PWM controller node for A13 / A10s ARM: sun5i: Add C.H.I.P DTS ARM: dts: sunxi: Add dtsi for AXP22x PMIC ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano ARM: sun5i: dt: Add UART3 CTS and RTS pins ... Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-22Merge tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu into next/dtOlof Johansson
mvebu dt for 4.4 (part 2) - Add support for severals Armada-370-based Seagate NAS - Fix Ready NAS device tree - Modify SDHCI binding for A388-GP allowing using it on old and new version of the board * tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu: ARM: mvebu: set SW polling as SDHCI card detection on A388-GP arm: mvebu: reorder nodes under internal-regs by address in RN2120 .dts file arm: mvebu: disable unused Armada RTC on ReadyNAS 102, 104 and 2120 ARM: mvebu: add DT support for Seagate Personal Cloud ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-22Merge tag 'socfpga_for_v4.4_cleanup' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA dts cleanup for v4.4 - Re-order DTS nodes into correct alphabetical order * tag 'socfpga_for_v4.4_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: socfpga: dts: sort nodes alphabetically Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-22Merge tag 'socfpga_dts_for_v4.4_part_2' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA DTS update for v4.4, part 2 - Add the FPGA manager node * tag 'socfpga_dts_for_v4.4_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: socfpga: dts: add fpga manager Signed-off-by: Olof Johansson <olof@lixom.net>
2015-10-20ARM: dts: am335x-base0033: Use IOPAD pinmux macroJavier Martinez Canillas
Use the AM33XX pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: am335x-igep0033: Use IOPAD pinmux macroJavier Martinez Canillas
Use the AM33xx pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: omap3-igep0020: Use IOPAD pinmux macroJavier Martinez Canillas
Use the OMAP3 pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_tsVignesh R
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power state via pinctrl and IO daisy chain using generic wakeirq framework. With commit 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree") i2c core allows optional wakeirq to be specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts to wake the system from low power state. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: Update Javier Martinez Canillas's emailJavier Martinez Canillas
I see that people are still sending emails to my old address (that no longer exists) since is the one mentioned in the IGEP DTS. Replace it with my current email address to avoid this. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpiosMugunthan V N
With the current implementation of GPIO hogging and with gpio-pcf857x is built as module, ethernet doesn't work on boot and doesn't throw any error/warning to user. Ethernet becomes operational when inserting gpio-pcf857x module, even this time there is no error/warning logs to user that ethernet is operational. When using with NFS rootfs and gpio-pcf857x as module, board doesn't boot as it doesn't get any ip address and doesn't throw any error/warning. To over come this, now cpsw driver tries to get mode-gpios. When gpio-pcf857x is built as module it will throw error, so that user can decide either to built in gpio-pcf857x to continue with nfs boot or choose alternate rootfs filesystem like sd/ramdisk. When using mmc/ramdisk as root fs, cpsw will probe defer and re-probes again when gpio-pcf857x module is inserted and ethernet becomes operational. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-19ARM: at91/dt: sama5d2: add missing devicesLudovic Desroches
Big update of the sama5d2.dtsi file since many patches have reached te mainline: - add generated clocks - enable crypto devices - add flexcom devices - add tdes device - add sdmmc devices Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: sama5d4: add the macb1 nodeGregory CLEMENT
The second macb is present on all the sama5d4 SoCs. Let's add a node reflecting it in the device tree. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: add pullup on mmc2 data signalsSylvain Rochet
MMC data lines may be left floating if nothing is currently driving the data lines, which is the case when mmc is in idle state, thus consuming a useless extra amount of power. Add pullup on mmc2 data signals in the same way it was previously done for mmc0 and mmc1. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: sama5d2_xplained: add regulator nodesWenyou Yang
Add regulator nodes of PMIC ACT8945A chip on the board. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: fix "disabled" property on at91rm9200Michael Opdenacker
Fix instances of "disable" instead of "disabled" in the at91rm9200 dtsi. Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: use syscon for PMCAlexandre Belloni
The PMC is not only used to drive the clocks but also has some registers related to other functions. One of those is for example the USB gadget bias. Using a syscon allows to properly separate those functions. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: dts: ls1021a: Add quirk for Erratum A009116Rajesh Bhagat
Add "snps,quirk-frame-length-adjustment" property to USB3 node for erratum A009116. This property provides value of GFLADJ_30MHZ for post silicon frame length adjustment. Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: imx6sx-sdb: Fix typo in regulator enable GPIO propertyLaurent Pinchart
The property name should be "gpio", not "gpios". Fix it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"Michael Opdenacker
Fix a typo, replacing "pinctrl-name" by "pinctrl-names" in the Phytec phyFLEX-i.MX6 Quad dtsi. Also fix a typo in the board name Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6: change the core clock of spdifShengjiu Wang
The correct core clock of spdif is SPDIF_GCLK, which is added to clock tree. So the dts also need to be updated. Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: vf-colibri: enable NAND flash controllerStefan Agner
Enable NAND access by adding pinmux and NAND flash controller node to device tree. The NAND chips currently used on the Colibri VF61 requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC strength per 2k page size. Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: vf610twr: add NAND flash controller peripherialStefan Agner
This adds the NAND flash controller (NFC) peripherial. The driver supports the SLC NAND chips found on Freescale's Vybrid Tower System Module. The Micron NAND chip on the module needs 4-bit ECC per 512 byte page. Use 24-bit ECC per 2k page, which is supported by the driver. Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: add Boundary Devices Nitrogen6_Lite boardGary Bisson
Based on an i.MX6 Solo with 512MB DDR3. http://boundarydevices.com/product/nitrogen6_lite/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: add Boundary Devices Nitrogen6_Max boardGary Bisson
Based on i.MX6 Quad with 4GB of DDR3. http://boundarydevices.com/product/nitrogen6max/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary DevicesGary Bisson
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary DevicesGary Bisson
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19of: Add Boundary Devices Inc. vendor prefixGary Bisson
This patch adds the vendor prefix for Boundary Devices Inc. which is a supplier of ARM-based single board computers and System-on-Modules for the general embedded market. Website: http://boundarydevices.com/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11Gary Bisson
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11Gary Bisson
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 supportGary Bisson
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6dql-nitrogen6x: add touchscreen supportGary Bisson
This patch adds the different touchscreens that can be connected using the displays available for this board. http://boundarydevices.com/product-category/displays/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-sabrelite: add Okaya LCD panelGary Bisson
This patch adds support for the 7" LCD display available for Sabrelite: http://boundarydevices.com/product/7-800x480-display/ Also add label to backlight_lcd and connect it to the panel. Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panelGary Bisson
This patch adds support for the 7" LCD display available for Nitrogen6x: http://boundarydevices.com/product/7-800x480-display/ Also add label to backlight_lcd and connect it to the panel. Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: vf500-colibri: Add device tree node for touchscreen supportSanchayan Maity
Add device tree node for touchscreen support on Colibri VF50. The touchscreen functionality on VF50 uses the ADC channels of Vybrid and some GPIOs. Also add pinctrl nodes for proper pinmux. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: i.MX35: fix cpu compatible valueVladimir Zapolskiy
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: i.MX31: fix cpu compatible valueVladimir Zapolskiy
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: imx7d add iomuxc lpsr device nodeAdrian Alonso
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel phandle allows to get input select register base address which is shared from main iomuxc controller. Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d-sdb: add fec1 and fec2 supportFugang Duan
Enable fec1 and fec2 for i.MX7d-sdb board. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d-pinfunc: add gpio1 pad iomux settingsAdrian Alonso
- Add imx7 SoC GPIO1 pad iomuxc settings <mux_reg conf_reg input_reg mux_mode input_val> - Fix UART input select daisy chain setting values Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit v1.2.3-58-ga151 (git 2.39.0) at 2024-12-21 11:37:03 +0000