| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
virtio: console: Use better variable names for fill_queue operation
virtio: console: Fix type of 'len' as unsigned int
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
x86, mrst: Fix whitespace breakage in apb_timer.c
x86, mrst: Fix APB timer per cpu clockevent
x86, mrst: Remove X86_MRST dependency on PCI_IOAPIC
x86, olpc: Use pci subarch init for OLPC
x86, pci: Add arch_init to x86_init abstraction
x86, mrst: Add Kconfig dependencies for Moorestown
x86, pci: Exclude Moorestown PCI code if CONFIG_X86_MRST=n
x86, numaq: Make CONFIG_X86_NUMAQ depend on CONFIG_PCI
x86, pci: Add sanity check for PCI fixed bar probing
x86, legacy_irq: Remove duplicate vector assigment
x86, legacy_irq: Remove left over nr_legacy_irqs
x86, mrst: Platform clock setup code
x86, apbt: Moorestown APB system timer driver
x86, mrst: Add vrtc platform data setup code
x86, mrst: Add platform timer info parsing code
x86, mrst: Fill in PCI functions in x86_init layer
x86, mrst: Add dummy legacy pic to platform setup
x86/PCI: Moorestown PCI support
x86, ioapic: Add dummy ioapic functions
x86, ioapic: Early enable ioapic for timer irq
...
Fixed up semantic conflict of new clocksources due to commit
17622339af25 ("clocksource: add argument to resume callback").
|
|
* 'for-linus/i2c' of git://git.fluff.org/bjdooks/linux:
i2c: Add support for Xilinx XPS IIC Bus Interface
i2c: omap: Add support for 16-bit registers
i2c-pnx: fix setting start/stop condition
powerpc: doc/dts-bindings: update doc of FSL I2C bindings
i2c-mpc: add support for the MPC512x processors from Freescale
i2c-mpc: rename "setclock" initialization functions to "setup"
i2c-mpc: use __devinit[data] for initialization functions and data
i2c/imx: don't add probe function to the driver struct
i2c: Add support for Ux500/Nomadik I2C controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (66 commits)
mfd: Fix ucb1x00 build failure for collie_defconfig
mfd: Fix lpc_sch related depends/selects, fix build error
gpio: Fix sch_gpio warning
gpio: add Intel SCH GPIO controller driver
i2c: convert i2c-isch to platform_device
mfd: Use completion interrupt for WM831x AUXADC
mfd: Use completion interrupt for WM835x AUXADC
mfd: Introduce remove_script function for twl4030
mfd/mmc: SDHI Kconfig update
mfd: sh_mobile_sdhi MMC_CAP_MMC_HIGHSPEED support
gpiolib: Force wm831x GPIOs into GPIO mode when requested
mfd: Add WM831x revision B support
gpiolib: Correct debugfs display of WM831x GPIO inversion
gpiolib: Actually set output state in wm831x_gpio_direction_output()
tmio_mmc: Balance cell enable()/disable() calls
tmio_mmc: Remove const from platform data V3
tmio_mmc: Use 100ms mmc_detect_change() delay
tmio_mmc: Add MMC_CAP_MMC_HIGHSPEED support V2
tmio_mmc: Keep card-detect interrupts enabled
mfd: Add twl6030 base addr for ID0, ID1, ID2
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (368 commits)
Staging: winbond: fix up wireless api errors
Staging: dream: camera: sk5k3e2fx: fix code style issues
Staging: dream: camera: msm_camera: fix code style issues
Staging: wlan-ng: More checkpatch.pl error cleanups
Staging: wlan-ng - checkpatch.pl fixups
Staging: comedi: comedi_fops.c: Checkpatch cleanup
Staging: comedi: fix suspect code indent in ni_labpc.c
Staging: comedi: fix yet another brace coding style issue in ni_labpc.c
Staging: comedi: fix another brace coding style issues in ni_labpc.c
Staging: comedi: fix brace coding style issue in ni_labpc.c
Staging: comedi: poc: Adding some KERN_ facility level
Staging: dream: camera: msm_camera: fix some code style issues
Staging: wlan-ng: fix most of the style issues in hfa384x.h
Staging: dream: camera: msm_camera: fix coding style issues
Staging: comedi: fix bracing coding style and 80 character issues in ni_660x.c
Staging: comedi: fix bracing coding style issue in ni_65xx.c
Staging: comedi: pcmad: Checkpatch cleanups
Staging: comedi: poc: fix coding style issues
staging: dt3155: revert u_long to u64 usage
Staging: comedi: drivers.c: Checkpatch cleanup
...
|
|
Fix kernel-doc notation in new seq-file functions and
correct spelling.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: Convert sh to use read/update_persistent_clock
sh: Move PMB debugfs entry initialization to later stage
sh: Fix up flush_cache_vmap() on SMP.
sh: fix up MMU reset with variable PMB mapping sizes.
sh: establish PMB mappings for NUMA nodes.
sh: check for existing mappings for bolted PMB entries.
sh: fixed virt/phys mapping helpers for PMB.
sh: make pmb iomapping configurable.
sh: reworked dynamic PMB mapping.
sh: Fix up cpumask_of_pcibus() for the NUMA build.
serial: sh-sci: Tidy up build warnings.
sh: Fix up ctrl_read/write stragglers in migor setup.
serial: sh-sci: Add DMA support.
dmaengine: shdma: extend .device_terminate_all() to record partial transfer
sh: merge sh7722 and sh7724 DMA register definitions
sh: activate runtime PM for dmaengine on sh7722 and sh7724
dmaengine: shdma: add runtime PM support.
dmaengine: shdma: separate DMA headers.
dmaengine: shdma: convert to platform device resources
dmaengine: shdma: fix DMA error handling.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: use __ratelimit in unaligned.c
parisc: Convert to read/update_persistent_clock
parisc: Simplify param.h by including <asm-generic/param.h>
parisc: drop unnecessary cast in __ldcw_align() macro
parisc: add strict copy size checks (v2)
parisc: remove trailing space in messages
parisc: ditto sys_accept4
parisc: wire up sys_recvmmsg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Provide generic subsystem-level callbacks
PM / Runtime: Document power.runtime_auto and related functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: set pci bus master enable bit
|
|
|
|
|
|
|
|
This patch adds support for the Xilinx XPS IIC Bus Interface.
The driver uses the dynamic mode, supporting to put several
I2C messages in the FIFO to reduce the number of interrupts.
It has the same feature as ocores, it can be passed a list
of devices that will be added when the bus is probed.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The current i2c-omap driver is set up for 32-bit registers, which
corresponds to most OMAP devices. However, OMAP730/850 based
devices use a 16-bit register size.
This change modifies the driver to perform a runtime CPU type check
to determine the register sizes, and uses a bit shift of either 1
or 2 bits to compute the proper register sizes for all registers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The start/stop condtions are set in different places repetedly in the i2c-pnx
driver. Beside in i2c_pnx_start and i2c_pnx_stop the start/stop bit are also
set during the transfer of a i2c message in the master_xmit/rcv calls. This is
wrong since we can't set the start/stop condition during the transaction of a
single message any way. As a matter of fact, the driver will sometimes set both
the start and the stop bits at one time. This can be easily reproduced by
sending a simple read request like e.g
struct i2c_msg msgs[] = {
{ addr, 0, 1, buf },
{ addr, I2C_M_RD, offset, buf }
};
While processing the first message the i2c_pnx_master_xmit will set both the
start_bit and the stop_bit, which will eventually confuse the slave.
Fixed by remove setting start/stop condition from the transmit routines.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch adds the MPC5121 to the list of supported devices,
enhances the doc of the "clock-frequency" property and removes
the obsolete "cell-index", "device_type" and "fsl-i2c" property.
Furthermore an example for the MPC5121 has been added.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
As I2C interrupts must be enabled for the MPC512x by the setup function
as well, "fsl,preserve-clocking" is handled in a slighly different way.
Also, the old settings are now reported calling dev_dbg(). For the
MPC512x the clock setup function of the MPC52xx can be re-used.
Furthermore, the Kconfig help has been updated and corrected.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
To prepare support for the MPC512x processors from Freescale the
"setclock" initialization functions have been renamed to "setup"
because I2C interrupts must be enabled for the MPC512x by this
function as well.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
"__devinit[data]" has not yet been used for all initialization functions
and data. To avoid truncating lines, the struct "mpc_i2c_match_data" has
been renamed to "mpc_i2c_data", which is even the better name.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Having a pointer to the probe function is unnecessary when using
platform_driver_probe and yields a section mismatch warning after
removing the white list entry "*driver" for
{ .data$, .data.rel$ } -> { .init.* } mismatches in modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This adds support for ST-Ericsson's I2C block found
in Ux500 and Nomadik 8815 platforms.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch fixes a build failure[1], by adding the missing semaphore.h include
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2234322/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We need to check for gpiochip_remove() errors.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Convert i2c-isch to platform_device for the lpc mfd core to add it at probe
time.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.
Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running. This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.
(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM
processors. While at it, make CONFIG_TMIO_MMC depend on
CONFIG_MFD_SH_MOBILE_SDHI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add MMC_CAP_MMC_HIGHSPEED support to the sh_mobile_sdhi
driver. Also, remove type cast and FIXME comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This is the chip default but it's possible the bootloader or OTP
will have been configured to a different mode (eg, to provide
feedback during startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds cell->disable() calls to the tmio-mmc
probe() error handling and the remove() function.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Remove const from the tmio-mmc platform data hclk V3.
This change makes it possible to remove the type cast
from the sh_mobile_sdhi driver which is using the clock
framework to get the clock rate.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch changes the tmio_mmc driver to wait 100ms
before checking the card detect status. This type of
delay is quite common among mmc drivers, it seems that
most hardware platforms need to give the hardware some
time to settle before checking card availabilty.
Hotplug is half-broken without this patch on the sh7724
Ecovec board. Hot insertion seems ok but eject is never
detected without this patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
On SuperH platforms the SDHI controller does not produce any command IRQs after
a completed IO. This leads to card-detect interrupts staying disabled. Do not
disable card-detect interrupts on DATA IRQs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add base address for generic slave ID0, ID1, ID2
and introduced one more entry to align RTC module number between
twl4030 and twl6030
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.
While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.
From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Intel Poulsbo (SCH) chipset LPC bridge controller contains several
functions. Creating and MFD driver for the LPC bridge controller allows
simultaneous use of SMBus and GPIO interfaces on the SCH.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
For ACPI based systems, we should check for ACPI conflicts when adding the
platform devices. The test will always succeed for non ACPI platforms.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Change the typo CONFIG_INPUT_TWL4030_PWBUTTON_MODULE in the
twl_has_pwrbutton definition to CONFIG_INPUT_TWL4030_PWRBUTTON_MODULE.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of
mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the
touchscreen driver of 88pm860x since IRQ handling is changed.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch fixes wrong goto statement for error handling on probe.
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use i2c_dummy in 88pm860x driver to avoid using static in probe function.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
