diff options
Diffstat (limited to 'tools/power/cpupower/README')
| -rw-r--r-- | tools/power/cpupower/README | 160 |
1 files changed, 150 insertions, 10 deletions
diff --git a/tools/power/cpupower/README b/tools/power/cpupower/README index 1c68f47663b2..2678ed81d311 100644 --- a/tools/power/cpupower/README +++ b/tools/power/cpupower/README @@ -22,16 +22,156 @@ interfaces [depending on configuration, see below]. compilation and installation ---------------------------- -make -su -make install - -should suffice on most systems. It builds libcpupower to put in -/usr/lib; cpupower, cpufreq-bench_plot.sh to put in /usr/bin; and -cpufreq-bench to put in /usr/sbin. If you want to set up the paths -differently and/or want to configure the package to your specific -needs, you need to open "Makefile" with an editor of your choice and -edit the block marked CONFIGURATION. +There are 2 output directories - one for the build output and another for +the installation of the build results, that is the utility, library, +man pages, etc... + +default directory +----------------- + +In the case of default directory, build and install process requires no +additional parameters: + +build +----- + +$ make + +The output directory for the 'make' command is the current directory and +its subdirs in the kernel tree: +tools/power/cpupower + +install +------- + +$ sudo make install + +'make install' command puts targets to default system dirs: + +----------------------------------------------------------------------- +| Installing file | System dir | +----------------------------------------------------------------------- +| libcpupower | /usr/lib | +----------------------------------------------------------------------- +| cpupower | /usr/bin | +----------------------------------------------------------------------- +| cpufreq-bench_plot.sh | /usr/bin | +----------------------------------------------------------------------- +| man pages | /usr/man | +----------------------------------------------------------------------- + +To put it in other words it makes build results available system-wide, +enabling any user to simply start using it without any additional steps + +custom directory +---------------- + +There are 2 make's command-line variables 'O' and 'DESTDIR' that setup +appropriate dirs: +'O' - build directory +'DESTDIR' - installation directory. This variable could also be setup in +the 'CONFIGURATION' block of the "Makefile" + +build +----- + +$ make O=<your_custom_build_catalog> + +Example: +$ make O=/home/hedin/prj/cpupower/build + +install +------- + +$ make O=<your_custom_build_catalog> DESTDIR=<your_custom_install_catalog> + +Example: +$ make O=/home/hedin/prj/cpupower/build DESTDIR=/home/hedin/prj/cpupower \ +> install + +Notice that both variables 'O' and 'DESTDIR' have been provided. The reason +is that the build results are saved in the custom output dir defined by 'O' +variable. So, this dir is the source for the installation step. If only +'DESTDIR' were provided then the 'install' target would assume that the +build directory is the current one, build everything there and install +from the current dir. + +The files will be installed to the following dirs: + +----------------------------------------------------------------------- +| Installing file | System dir | +----------------------------------------------------------------------- +| libcpupower | ${DESTDIR}/usr/lib | +----------------------------------------------------------------------- +| cpupower | ${DESTDIR}/usr/bin | +----------------------------------------------------------------------- +| cpufreq-bench_plot.sh | ${DESTDIR}/usr/bin | +----------------------------------------------------------------------- +| man pages | ${DESTDIR}/usr/man | +----------------------------------------------------------------------- + +If you look at the table for the default 'make' output dirs you will +notice that the only difference with the non-default case is the +${DESTDIR} prefix. So, the structure of the output dirs remains the same +regardles of the root output directory. + + +clean and uninstall +------------------- + +'clean' target is intended for cleanup the build catalog from build results +'uninstall' target is intended for removing installed files from the +installation directory + +default directory +----------------- + +This case is a straightforward one: +$ make clean +$ make uninstall + +custom directory +---------------- + +Use 'O' command line variable to remove previously built files from the +build dir: +$ make O=<your_custom_build_catalog> clean + +Example: +$ make O=/home/hedin/prj/cpupower/build clean + +Use 'DESTDIR' command line variable to uninstall previously installed files +from the given dir: +$ make DESTDIR=<your_custom_install_catalog> + +Example: +make DESTDIR=/home/hedin/prj/cpupower uninstall + + +running the tool +---------------- + +default directory +----------------- + +$ sudo cpupower + +custom directory +---------------- + +When it comes to run the utility from the custom build catalog things +become a little bit complicated as 'just run' approach doesn't work. +Assuming that the current dir is '<your_custom_install_catalog>/usr', +issuing the following command: + +$ sudo ./bin/cpupower +will produce the following error output: +./bin/cpupower: error while loading shared libraries: libcpupower.so.1: +cannot open shared object file: No such file or directory + +The issue is that binary cannot find the 'libcpupower' library. So, we +shall point to the lib dir: +sudo LD_LIBRARY_PATH=lib64/ ./bin/cpupower THANKS |