diff options
Diffstat (limited to 'include/linux/power/smb347-charger.h')
| -rw-r--r-- | include/linux/power/smb347-charger.h | 114 |
1 files changed, 0 insertions, 114 deletions
diff --git a/include/linux/power/smb347-charger.h b/include/linux/power/smb347-charger.h deleted file mode 100644 index e0b687a4d20c..000000000000 --- a/include/linux/power/smb347-charger.h +++ /dev/null @@ -1,114 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-only */ -/* - * Summit Microelectronics SMB347 Battery Charger Driver - * - * Copyright (C) 2011, Intel Corporation - * - * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com> - * Mika Westerberg <mika.westerberg@linux.intel.com> - */ - -#ifndef SMB347_CHARGER_H -#define SMB347_CHARGER_H - -#include <linux/types.h> -#include <linux/power_supply.h> - -enum { - /* use the default compensation method */ - SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1, - - SMB347_SOFT_TEMP_COMPENSATE_NONE, - SMB347_SOFT_TEMP_COMPENSATE_CURRENT, - SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE, -}; - -/* Use default factory programmed value for hard/soft temperature limit */ -#define SMB347_TEMP_USE_DEFAULT -273 - -/* - * Charging enable can be controlled by software (via i2c) by - * smb347-charger driver or by EN pin (active low/high). - */ -enum smb347_chg_enable { - SMB347_CHG_ENABLE_SW, - SMB347_CHG_ENABLE_PIN_ACTIVE_LOW, - SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH, -}; - -/** - * struct smb347_charger_platform_data - platform data for SMB347 charger - * @battery_info: Information about the battery - * @max_charge_current: maximum current (in uA) the battery can be charged - * @max_charge_voltage: maximum voltage (in uV) the battery can be charged - * @pre_charge_current: current (in uA) to use in pre-charging phase - * @termination_current: current (in uA) used to determine when the - * charging cycle terminates - * @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to - * pre-charge to fast charge mode - * @mains_current_limit: maximum input current drawn from AC/DC input (in uA) - * @usb_hc_current_limit: maximum input high current (in uA) drawn from USB - * input - * @chip_temp_threshold: die temperature where device starts limiting charge - * current [%100 - %130] (in degree C) - * @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C), - * granularity is 5 deg C. - * @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C), - * granularity is 5 deg C. - * @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C), - * granularity is 5 deg C. - * @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C), - * granularity is 5 deg C. - * @suspend_on_hard_temp_limit: suspend charging when hard limit is hit - * @soft_temp_limit_compensation: compensation method when soft temperature - * limit is hit - * @charge_current_compensation: current (in uA) for charging compensation - * current when temperature hits soft limits - * @use_mains: AC/DC input can be used - * @use_usb: USB input can be used - * @use_usb_otg: USB OTG output can be used (not implemented yet) - * @irq_gpio: GPIO number used for interrupts (%-1 if not used) - * @enable_control: how charging enable/disable is controlled - * (driver/pin controls) - * - * @use_main, @use_usb, and @use_usb_otg are means to enable/disable - * hardware support for these. This is useful when we want to have for - * example OTG charging controlled via OTG transceiver driver and not by - * the SMB347 hardware. - * - * Hard and soft temperature limit values are given as described in the - * device data sheet and assuming NTC beta value is %3750. Even if this is - * not the case, these values should be used. They can be mapped to the - * corresponding NTC beta values with the help of table %2 in the data - * sheet. So for example if NTC beta is %3375 and we want to program hard - * hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50. - * - * If zero value is given in any of the current and voltage values, the - * factory programmed default will be used. For soft/hard temperature - * values, pass in %SMB347_TEMP_USE_DEFAULT instead. - */ -struct smb347_charger_platform_data { - struct power_supply_info battery_info; - unsigned int max_charge_current; - unsigned int max_charge_voltage; - unsigned int pre_charge_current; - unsigned int termination_current; - unsigned int pre_to_fast_voltage; - unsigned int mains_current_limit; - unsigned int usb_hc_current_limit; - unsigned int chip_temp_threshold; - int soft_cold_temp_limit; - int soft_hot_temp_limit; - int hard_cold_temp_limit; - int hard_hot_temp_limit; - bool suspend_on_hard_temp_limit; - unsigned int soft_temp_limit_compensation; - unsigned int charge_current_compensation; - bool use_mains; - bool use_usb; - bool use_usb_otg; - int irq_gpio; - enum smb347_chg_enable enable_control; -}; - -#endif /* SMB347_CHARGER_H */ |