diff options
Diffstat (limited to 'include/linux/mtd/spi-nor.h')
| -rw-r--r-- | include/linux/mtd/spi-nor.h | 214 |
1 files changed, 214 insertions, 0 deletions
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h new file mode 100644 index 000000000000..53241842a7ab --- /dev/null +++ b/include/linux/mtd/spi-nor.h @@ -0,0 +1,214 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __LINUX_MTD_SPI_NOR_H +#define __LINUX_MTD_SPI_NOR_H + +/* + * Note on opcode nomenclature: some opcodes have a format like + * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number + * of I/O lines used for the opcode, address, and data (respectively). The + * FUNCTION has an optional suffix of '4', to represent an opcode which + * requires a 4-byte (32-bit) address. + */ + +/* Flash opcodes. */ +#define SPINOR_OP_WREN 0x06 /* Write enable */ +#define SPINOR_OP_RDSR 0x05 /* Read status register */ +#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */ +#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */ +#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */ +#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual SPI) */ +#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad SPI) */ +#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */ +#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */ +#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */ +#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */ +#define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */ +#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */ +#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */ +#define SPINOR_OP_RDCR 0x35 /* Read configuration register */ + +/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ +#define SPINOR_OP_READ4 0x13 /* Read data bytes (low frequency) */ +#define SPINOR_OP_READ4_FAST 0x0c /* Read data bytes (high frequency) */ +#define SPINOR_OP_READ4_1_1_2 0x3c /* Read data bytes (Dual SPI) */ +#define SPINOR_OP_READ4_1_1_4 0x6c /* Read data bytes (Quad SPI) */ +#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */ +#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */ + +/* Used for SST flashes only. */ +#define SPINOR_OP_BP 0x02 /* Byte program */ +#define SPINOR_OP_WRDI 0x04 /* Write disable */ +#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */ + +/* Used for Macronix and Winbond flashes. */ +#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ +#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ + +/* Used for Spansion flashes only. */ +#define SPINOR_OP_BRWR 0x17 /* Bank register write */ + +/* Status Register bits. */ +#define SR_WIP 1 /* Write in progress */ +#define SR_WEL 2 /* Write enable latch */ +/* meaning of other SR_* bits may differ between vendors */ +#define SR_BP0 4 /* Block protect 0 */ +#define SR_BP1 8 /* Block protect 1 */ +#define SR_BP2 0x10 /* Block protect 2 */ +#define SR_SRWD 0x80 /* SR write protect */ + +#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */ + +/* Configuration Register bits. */ +#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */ + +enum read_mode { + SPI_NOR_NORMAL = 0, + SPI_NOR_FAST, + SPI_NOR_DUAL, + SPI_NOR_QUAD, +}; + +/** + * struct spi_nor_xfer_cfg - Structure for defining a Serial Flash transfer + * @wren: command for "Write Enable", or 0x00 for not required + * @cmd: command for operation + * @cmd_pins: number of pins to send @cmd (1, 2, 4) + * @addr: address for operation + * @addr_pins: number of pins to send @addr (1, 2, 4) + * @addr_width: number of address bytes + * (3,4, or 0 for address not required) + * @mode: mode data + * @mode_pins: number of pins to send @mode (1, 2, 4) + * @mode_cycles: number of mode cycles (0 for mode not required) + * @dummy_cycles: number of dummy cycles (0 for dummy not required) + */ +struct spi_nor_xfer_cfg { + u8 wren; + u8 cmd; + u8 cmd_pins; + u32 addr; + u8 addr_pins; + u8 addr_width; + u8 mode; + u8 mode_pins; + u8 mode_cycles; + u8 dummy_cycles; +}; + +#define SPI_NOR_MAX_CMD_SIZE 8 +enum spi_nor_ops { + SPI_NOR_OPS_READ = 0, + SPI_NOR_OPS_WRITE, + SPI_NOR_OPS_ERASE, + SPI_NOR_OPS_LOCK, + SPI_NOR_OPS_UNLOCK, +}; + +/** + * struct spi_nor - Structure for defining a the SPI NOR layer + * @mtd: point to a mtd_info structure + * @lock: the lock for the read/write/erase/lock/unlock operations + * @dev: point to a spi device, or a spi nor controller device. + * @page_size: the page size of the SPI NOR + * @addr_width: number of address bytes + * @erase_opcode: the opcode for erasing a sector + * @read_opcode: the read opcode + * @read_dummy: the dummy needed by the read operation + * @program_opcode: the program opcode + * @flash_read: the mode of the read + * @sst_write_second: used by the SST write operation + * @cfg: used by the read_xfer/write_xfer + * @cmd_buf: used by the write_reg + * @prepare: [OPTIONAL] do some preparations for the + * read/write/erase/lock/unlock operations + * @unprepare: [OPTIONAL] do some post work after the + * read/write/erase/lock/unlock operations + * @read_xfer: [OPTIONAL] the read fundamental primitive + * @write_xfer: [OPTIONAL] the writefundamental primitive + * @read_reg: [DRIVER-SPECIFIC] read out the register + * @write_reg: [DRIVER-SPECIFIC] write data to the register + * @read_id: [REPLACEABLE] read out the ID data, and find + * the proper spi_device_id + * @wait_till_ready: [REPLACEABLE] wait till the NOR becomes ready + * @read: [DRIVER-SPECIFIC] read data from the SPI NOR + * @write: [DRIVER-SPECIFIC] write data to the SPI NOR + * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR + * at the offset @offs + * @priv: the private data + */ +struct spi_nor { + struct mtd_info *mtd; + struct mutex lock; + struct device *dev; + u32 page_size; + u8 addr_width; + u8 erase_opcode; + u8 read_opcode; + u8 read_dummy; + u8 program_opcode; + enum read_mode flash_read; + bool sst_write_second; + struct spi_nor_xfer_cfg cfg; + u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE]; + + int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops); + void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops); + int (*read_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg, + u8 *buf, size_t len); + int (*write_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg, + u8 *buf, size_t len); + int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len); + int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len, + int write_enable); + const struct spi_device_id *(*read_id)(struct spi_nor *nor); + int (*wait_till_ready)(struct spi_nor *nor); + + int (*read)(struct spi_nor *nor, loff_t from, + size_t len, size_t *retlen, u_char *read_buf); + void (*write)(struct spi_nor *nor, loff_t to, + size_t len, size_t *retlen, const u_char *write_buf); + int (*erase)(struct spi_nor *nor, loff_t offs); + + void *priv; +}; + +/** + * spi_nor_scan() - scan the SPI NOR + * @nor: the spi_nor structure + * @id: the spi_device_id provided by the driver + * @mode: the read mode supported by the driver + * + * The drivers can use this fuction to scan the SPI NOR. + * In the scanning, it will try to get all the necessary information to + * fill the mtd_info{} and the spi_nor{}. + * + * The board may assigns a spi_device_id with @id which be used to compared with + * the spi_device_id detected by the scanning. + * + * Return: 0 for success, others for failure. + */ +int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id, + enum read_mode mode); +extern const struct spi_device_id spi_nor_ids[]; + +/** + * spi_nor_match_id() - find the spi_device_id by the name + * @name: the name of the spi_device_id + * + * The drivers use this function to find the spi_device_id + * specified by the @name. + * + * Return: returns the right spi_device_id pointer on success, + * and returns NULL on failure. + */ +const struct spi_device_id *spi_nor_match_id(char *name); + +#endif |