diff options
Diffstat (limited to 'drivers/phy/qualcomm/phy-qcom-qmp.c')
-rw-r--r-- | drivers/phy/qualcomm/phy-qcom-qmp.c | 177 |
1 files changed, 176 insertions, 1 deletions
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index 55b83974b531..ba6c5b2e4898 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -61,6 +61,19 @@ #define USB3_MODE BIT(0) /* enables USB3 mode */ #define DP_MODE BIT(1) /* enables DP mode */ +/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */ +#define ARCVR_DTCT_EN BIT(0) +#define ALFPS_DTCT_EN BIT(1) +#define ARCVR_DTCT_EVENT_SEL BIT(4) + +/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */ +#define IRQ_CLEAR BIT(0) + +/* QPHY_PCS_LFPS_RXTERM_IRQ_STATUS register bits */ +#define RCVR_DETECT BIT(0) + +/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */ +#define CLAMP_EN BIT(0) /* enables i/o clamp_n */ #define PHY_INIT_COMPLETE_TIMEOUT 1000 #define POWER_DOWN_DELAY_US_MIN 10 @@ -108,6 +121,9 @@ enum qphy_reg_layout { QPHY_SW_RESET, QPHY_START_CTRL, QPHY_PCS_READY_STATUS, + QPHY_PCS_AUTONOMOUS_MODE_CTRL, + QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR, + QPHY_PCS_LFPS_RXTERM_IRQ_STATUS, }; static const unsigned int pciephy_regs_layout[] = { @@ -135,12 +151,18 @@ static const unsigned int usb3phy_regs_layout[] = { [QPHY_SW_RESET] = 0x00, [QPHY_START_CTRL] = 0x08, [QPHY_PCS_READY_STATUS] = 0x17c, + [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d4, + [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0d8, + [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x178, }; static const unsigned int qmp_v3_usb3phy_regs_layout[] = { [QPHY_SW_RESET] = 0x00, [QPHY_START_CTRL] = 0x08, [QPHY_PCS_READY_STATUS] = 0x174, + [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d8, + [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0dc, + [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170, }; static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = { @@ -536,6 +558,7 @@ struct qmp_phy_cfg { * @tx: iomapped memory space for lane's tx * @rx: iomapped memory space for lane's rx * @pcs: iomapped memory space for lane's pcs + * @pcs_misc: iomapped memory space for lane's pcs_misc * @pipe_clk: pipe lock * @index: lane index * @qmp: QMP phy to which this lane belongs @@ -546,6 +569,7 @@ struct qmp_phy { void __iomem *tx; void __iomem *rx; void __iomem *pcs; + void __iomem *pcs_misc; struct clk *pipe_clk; unsigned int index; struct qcom_qmp *qmp; @@ -567,6 +591,8 @@ struct qmp_phy { * @phys: array of per-lane phy descriptors * @phy_mutex: mutex lock for PHY common block initialization * @init_count: phy common block initialization count + * @phy_initialized: indicate if PHY has been initialized + * @mode: current PHY mode */ struct qcom_qmp { struct device *dev; @@ -582,6 +608,8 @@ struct qcom_qmp { struct mutex phy_mutex; int init_count; + bool phy_initialized; + enum phy_mode mode; }; static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val) @@ -995,6 +1023,7 @@ static int qcom_qmp_phy_init(struct phy *phy) dev_err(qmp->dev, "phy initialization timed-out\n"); goto err_pcs_ready; } + qmp->phy_initialized = true; return ret; @@ -1029,6 +1058,128 @@ static int qcom_qmp_phy_exit(struct phy *phy) qcom_qmp_phy_com_exit(qmp); + qmp->phy_initialized = false; + + return 0; +} + +static int qcom_qmp_phy_set_mode(struct phy *phy, enum phy_mode mode) +{ + struct qmp_phy *qphy = phy_get_drvdata(phy); + struct qcom_qmp *qmp = qphy->qmp; + + qmp->mode = mode; + + return 0; +} + +static void qcom_qmp_phy_enable_autonomous_mode(struct qmp_phy *qphy) +{ + struct qcom_qmp *qmp = qphy->qmp; + const struct qmp_phy_cfg *cfg = qmp->cfg; + void __iomem *pcs = qphy->pcs; + void __iomem *pcs_misc = qphy->pcs_misc; + u32 intr_mask; + + if (qmp->mode == PHY_MODE_USB_HOST_SS || + qmp->mode == PHY_MODE_USB_DEVICE_SS) + intr_mask = ARCVR_DTCT_EN | ALFPS_DTCT_EN; + else + intr_mask = ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL; + + /* Clear any pending interrupts status */ + qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR); + /* Writing 1 followed by 0 clears the interrupt */ + qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR); + + qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], + ARCVR_DTCT_EN | ALFPS_DTCT_EN | ARCVR_DTCT_EVENT_SEL); + + /* Enable required PHY autonomous mode interrupts */ + qphy_setbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], intr_mask); + + /* Enable i/o clamp_n for autonomous mode */ + if (pcs_misc) + qphy_clrbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN); +} + +static void qcom_qmp_phy_disable_autonomous_mode(struct qmp_phy *qphy) +{ + struct qcom_qmp *qmp = qphy->qmp; + const struct qmp_phy_cfg *cfg = qmp->cfg; + void __iomem *pcs = qphy->pcs; + void __iomem *pcs_misc = qphy->pcs_misc; + + /* Disable i/o clamp_n on resume for normal mode */ + if (pcs_misc) + qphy_setbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN); + + qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], + ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL | ALFPS_DTCT_EN); + + qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR); + /* Writing 1 followed by 0 clears the interrupt */ + qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR); +} + +static int __maybe_unused qcom_qmp_phy_runtime_suspend(struct device *dev) +{ + struct qcom_qmp *qmp = dev_get_drvdata(dev); + struct qmp_phy *qphy = qmp->phys[0]; + const struct qmp_phy_cfg *cfg = qmp->cfg; + + dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->mode); + + /* Supported only for USB3 PHY */ + if (cfg->type != PHY_TYPE_USB3) + return 0; + + if (!qmp->phy_initialized) { + dev_vdbg(dev, "PHY not initialized, bailing out\n"); + return 0; + } + + qcom_qmp_phy_enable_autonomous_mode(qphy); + + clk_disable_unprepare(qphy->pipe_clk); + clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); + + return 0; +} + +static int __maybe_unused qcom_qmp_phy_runtime_resume(struct device *dev) +{ + struct qcom_qmp *qmp = dev_get_drvdata(dev); + struct qmp_phy *qphy = qmp->phys[0]; + const struct qmp_phy_cfg *cfg = qmp->cfg; + int ret = 0; + + dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->mode); + + /* Supported only for USB3 PHY */ + if (cfg->type != PHY_TYPE_USB3) + return 0; + + if (!qmp->phy_initialized) { + dev_vdbg(dev, "PHY not initialized, bailing out\n"); + return 0; + } + + ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks); + if (ret) { + dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret); + return ret; + } + + ret = clk_prepare_enable(qphy->pipe_clk); + if (ret) { + dev_err(dev, "pipe_clk enable failed, err=%d\n", ret); + clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); + return ret; + } + + qcom_qmp_phy_disable_autonomous_mode(qphy); + return 0; } @@ -1142,6 +1293,7 @@ static const struct phy_ops qcom_qmp_phy_gen_ops = { .init = qcom_qmp_phy_init, .exit = qcom_qmp_phy_exit, .power_on = qcom_qmp_phy_poweron, + .set_mode = qcom_qmp_phy_set_mode, .owner = THIS_MODULE, }; @@ -1160,7 +1312,8 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id) /* * Get memory resources for each phy lane: - * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2. + * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2; and + * pcs_misc (optional) -> 3. */ qphy->tx = of_iomap(np, 0); if (!qphy->tx) @@ -1174,6 +1327,10 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id) if (!qphy->pcs) return -ENOMEM; + qphy->pcs_misc = of_iomap(np, 3); + if (!qphy->pcs_misc) + dev_vdbg(dev, "PHY pcs_misc-reg not used\n"); + /* * Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3 * based phys, so they essentially have pipe clock. So, @@ -1240,6 +1397,11 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = { }; MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table); +static const struct dev_pm_ops qcom_qmp_phy_pm_ops = { + SET_RUNTIME_PM_OPS(qcom_qmp_phy_runtime_suspend, + qcom_qmp_phy_runtime_resume, NULL) +}; + static int qcom_qmp_phy_probe(struct platform_device *pdev) { struct qcom_qmp *qmp; @@ -1308,12 +1470,21 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev) return -ENOMEM; id = 0; + pm_runtime_set_active(dev); + pm_runtime_enable(dev); + /* + * Prevent runtime pm from being ON by default. Users can enable + * it using power/control in sysfs. + */ + pm_runtime_forbid(dev); + for_each_available_child_of_node(dev->of_node, child) { /* Create per-lane phy */ ret = qcom_qmp_phy_create(dev, child, id); if (ret) { dev_err(dev, "failed to create lane%d phy, %d\n", id, ret); + pm_runtime_disable(dev); return ret; } @@ -1325,6 +1496,7 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev) if (ret) { dev_err(qmp->dev, "failed to register pipe clock source\n"); + pm_runtime_disable(dev); return ret; } id++; @@ -1333,6 +1505,8 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev) phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); if (!IS_ERR(phy_provider)) dev_info(dev, "Registered Qcom-QMP phy\n"); + else + pm_runtime_disable(dev); return PTR_ERR_OR_ZERO(phy_provider); } @@ -1341,6 +1515,7 @@ static struct platform_driver qcom_qmp_phy_driver = { .probe = qcom_qmp_phy_probe, .driver = { .name = "qcom-qmp-phy", + .pm = &qcom_qmp_phy_pm_ops, .of_match_table = qcom_qmp_phy_of_match_table, }, }; |