diff options
Diffstat (limited to 'drivers/mfd')
51 files changed, 2185 insertions, 1197 deletions
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 33834120d057..6cc4b6acc22a 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -67,6 +67,18 @@ config MFD_BCM590XX help Support for the BCM590xx PMUs from Broadcom +config MFD_AXP20X + bool "X-Powers AXP20X" + select MFD_CORE + select REGMAP_I2C + select REGMAP_IRQ + depends on I2C=y + help + If you say Y here you get support for the X-Powers AXP202 and AXP209. + This driver include only the core APIs. You have to select individual + components like regulators or the PEK (Power Enable Key) under the + corresponding menus. + config MFD_CROS_EC tristate "ChromeOS Embedded Controller" select MFD_CORE @@ -250,6 +262,16 @@ config MFD_INTEL_MSIC Passage) chip. This chip embeds audio, battery, GPIO, etc. devices used in Intel Medfield platforms. +config MFD_IPAQ_MICRO + bool "Atmel Micro ASIC (iPAQ h3100/h3600/h3700) Support" + depends on SA1100_H3100 || SA1100_H3600 + select MFD_CORE + help + Select this to get support for the Microcontroller found in + the Compaq iPAQ handheld computers. This is an Atmel + AT90LS8535 microcontroller flashed with a special iPAQ + firmware using the custom protocol implemented in this driver. + config MFD_JANZ_CMODIO tristate "Janz CMOD-IO PCI MODULbus Carrier Board" select MFD_CORE @@ -331,15 +353,15 @@ config MFD_88PM860X battery-charger under the corresponding menus. config MFD_MAX14577 - bool "Maxim Semiconductor MAX14577 MUIC + Charger Support" + bool "Maxim Semiconductor MAX14577/77836 MUIC + Charger Support" depends on I2C=y select MFD_CORE select REGMAP_I2C select REGMAP_IRQ select IRQ_DOMAIN help - Say yes here to add support for Maxim Semiconductor MAX14577. - This is a Micro-USB IC with Charger controls on chip. + Say yes here to add support for Maxim Semiconductor MAX14577 and + MAX77836 Micro-USB ICs with battery charger. This driver provides common support for accessing the device; additional drivers must be enabled in order to use the functionality of the device. @@ -675,6 +697,7 @@ config MFD_DB8500_PRCMU config MFD_STMPE bool "STMicroelectronics STMPE" depends on (I2C=y || SPI_MASTER=y) + depends on OF select MFD_CORE help Support for the STMPE family of I/O Expanders from @@ -719,6 +742,14 @@ config MFD_STA2X11 select MFD_CORE select REGMAP_MMIO +config MFD_SUN6I_PRCM + bool "Allwinner A31 PRCM controller" + depends on ARCH_SUNXI + select MFD_CORE + help + Support for the PRCM (Power/Reset/Clock Management) unit available + in A31 SoC. + config MFD_SYSCON bool "System Controller Register R/W Based on Regmap" select REGMAP_MMIO @@ -729,6 +760,7 @@ config MFD_SYSCON config MFD_DAVINCI_VOICECODEC tristate select MFD_CORE + select REGMAP_MMIO config MFD_TI_AM335X_TSCADC tristate "TI ADC / Touch Screen chip support" @@ -1194,7 +1226,7 @@ config MFD_WM8994 functionaltiy of the device other drivers must be enabled. config MFD_STW481X - bool "Support for ST Microelectronics STw481x" + tristate "Support for ST Microelectronics STw481x" depends on I2C && ARCH_NOMADIK select REGMAP_I2C select MFD_CORE @@ -1217,7 +1249,7 @@ config MCP_SA11X0 # Chip drivers config MCP_UCB1200 - bool "Support for UCB1200 / UCB1300" + tristate "Support for UCB1200 / UCB1300" depends on MCP_SA11X0 select MCP @@ -1227,12 +1259,17 @@ config MCP_UCB1200_TS endmenu -config VEXPRESS_CONFIG - bool "ARM Versatile Express platform infrastructure" - depends on ARM || ARM64 +config MFD_VEXPRESS_SYSREG + bool "Versatile Express System Registers" + depends on VEXPRESS_CONFIG && GPIOLIB + default y + select CLKSRC_MMIO + select GPIO_GENERIC_PLATFORM + select MFD_CORE + select MFD_SYSCON help - Platform configuration infrastructure for the ARM Ltd. - Versatile Express. + System Registers are the platform configuration block + on the ARM Ltd. Versatile Express board. endmenu endif diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 2851275e2656..8afedba535c7 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -29,6 +29,7 @@ obj-$(CONFIG_MFD_STA2X11) += sta2x11-mfd.o obj-$(CONFIG_MFD_STMPE) += stmpe.o obj-$(CONFIG_STMPE_I2C) += stmpe-i2c.o obj-$(CONFIG_STMPE_SPI) += stmpe-spi.o +obj-$(CONFIG_MFD_SUN6I_PRCM) += sun6i-prcm.o obj-$(CONFIG_MFD_TC3589X) += tc3589x.o obj-$(CONFIG_MFD_T7L66XB) += t7l66xb.o tmio_core.o obj-$(CONFIG_MFD_TC6387XB) += tc6387xb.o tmio_core.o @@ -102,6 +103,7 @@ obj-$(CONFIG_PMIC_DA9052) += da9052-irq.o obj-$(CONFIG_PMIC_DA9052) += da9052-core.o obj-$(CONFIG_MFD_DA9052_SPI) += da9052-spi.o obj-$(CONFIG_MFD_DA9052_I2C) += da9052-i2c.o +obj-$(CONFIG_MFD_AXP20X) += axp20x.o obj-$(CONFIG_MFD_LP3943) += lp3943.o obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o @@ -161,8 +163,9 @@ obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o obj-$(CONFIG_MFD_SYSCON) += syscon.o obj-$(CONFIG_MFD_LM3533) += lm3533-core.o lm3533-ctrlbank.o -obj-$(CONFIG_VEXPRESS_CONFIG) += vexpress-config.o vexpress-sysreg.o +obj-$(CONFIG_MFD_VEXPRESS_SYSREG) += vexpress-sysreg.o obj-$(CONFIG_MFD_RETU) += retu-mfd.o obj-$(CONFIG_MFD_AS3711) += as3711.o obj-$(CONFIG_MFD_AS3722) += as3722.o obj-$(CONFIG_MFD_STW481X) += stw481x.o +obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c index a8ee4a36a1d8..cf2e6a198c6b 100644 --- a/drivers/mfd/ab8500-core.c +++ b/drivers/mfd/ab8500-core.c @@ -591,7 +591,7 @@ static int ab8500_irq_init(struct ab8500 *ab8500, struct device_node *np) num_irqs = AB8500_NR_IRQS; /* If ->irq_base is zero this will give a linear mapping */ - ab8500->domain = irq_domain_add_simple(NULL, + ab8500->domain = irq_domain_add_simple(ab8500->dev->of_node, num_irqs, 0, &ab8500_irq_ops, ab8500); diff --git a/drivers/mfd/abx500-core.c b/drivers/mfd/abx500-core.c index f3a15aa54d7b..fe418995108c 100644 --- a/drivers/mfd/abx500-core.c +++ b/drivers/mfd/abx500-core.c @@ -151,22 +151,6 @@ int abx500_startup_irq_enabled(struct device *dev, unsigned int irq) } EXPORT_SYMBOL(abx500_startup_irq_enabled); -void abx500_dump_all_banks(void) -{ - struct abx500_ops *ops; - struct device dummy_child = {NULL}; - struct abx500_device_entry *dev_entry; - - list_for_each_entry(dev_entry, &abx500_list, list) { - dummy_child.parent = dev_entry->dev; - ops = &dev_entry->ops; - - if ((ops != NULL) && (ops->dump_all_banks != NULL)) - ops->dump_all_banks(&dummy_child); - } -} -EXPORT_SYMBOL(abx500_dump_all_banks); - MODULE_AUTHOR("Mattias Wallin <mattias.wallin@stericsson.com>"); MODULE_DESCRIPTION("ABX500 core driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c index 07e6e27be23c..cfc191abae4a 100644 --- a/drivers/mfd/arizona-core.c +++ b/drivers/mfd/arizona-core.c @@ -583,6 +583,7 @@ static const char *wm5102_supplies[] = { "CPVDD", "SPKVDDL", "SPKVDDR", + "MICVDD", }; static const struct mfd_cell wm5102_devs[] = { diff --git a/drivers/mfd/arizona-irq.c b/drivers/mfd/arizona-irq.c index 88758ab9402b..17102f589100 100644 --- a/drivers/mfd/arizona-irq.c +++ b/drivers/mfd/arizona-irq.c @@ -285,7 +285,7 @@ int arizona_irq_init(struct arizona *arizona) IRQF_ONESHOT, -1, irq, &arizona->irq_chip); if (ret != 0) { - dev_err(arizona->dev, "Failed to add AOD IRQs: %d\n", ret); + dev_err(arizona->dev, "Failed to add main IRQs: %d\n", ret); goto err_aod; } diff --git a/drivers/mfd/as3711.c b/drivers/mfd/as3711.c index ec684fcedb42..d9706ede8d39 100644 --- a/drivers/mfd/as3711.c +++ b/drivers/mfd/as3711.c @@ -114,7 +114,7 @@ static const struct regmap_config as3711_regmap_config = { }; #ifdef CONFIG_OF -static struct of_device_id as3711_of_match[] = { +static const struct of_device_id as3711_of_match[] = { {.compatible = "ams,as3711",}, {} }; diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c new file mode 100644 index 000000000000..dee653989e3a --- /dev/null +++ b/drivers/mfd/axp20x.c @@ -0,0 +1,258 @@ +/* + * axp20x.c - MFD core driver for the X-Powers AXP202 and AXP209 + * + * AXP20x comprises an adaptive USB-Compatible PWM charger, 2 BUCK DC-DC + * converters, 5 LDOs, multiple 12-bit ADCs of voltage, current and temperature + * as well as 4 configurable GPIOs. + * + * Author: Carlo Caione <carlo@caione.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <linux/regulator/consumer.h> +#include <linux/mfd/axp20x.h> +#include <linux/mfd/core.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> + +#define AXP20X_OFF 0x80 + +static const struct regmap_range axp20x_writeable_ranges[] = { + regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE), + regmap_reg_range(AXP20X_DCDC_MODE, AXP20X_FG_RES), +}; + +static const struct regmap_range axp20x_volatile_ranges[] = { + regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ5_STATE), +}; + +static const struct regmap_access_table axp20x_writeable_table = { + .yes_ranges = axp20x_writeable_ranges, + .n_yes_ranges = ARRAY_SIZE(axp20x_writeable_ranges), +}; + +static const struct regmap_access_table axp20x_volatile_table = { + .yes_ranges = axp20x_volatile_ranges, + .n_yes_ranges = ARRAY_SIZE(axp20x_volatile_ranges), +}; + +static struct resource axp20x_pek_resources[] = { + { + .name = "PEK_DBR", + .start = AXP20X_IRQ_PEK_RIS_EDGE, + .end = AXP20X_IRQ_PEK_RIS_EDGE, + .flags = IORESOURCE_IRQ, + }, { + .name = "PEK_DBF", + .start = AXP20X_IRQ_PEK_FAL_EDGE, + .end = AXP20X_IRQ_PEK_FAL_EDGE, + .flags = IORESOURCE_IRQ, + }, +}; + +static const struct regmap_config axp20x_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .wr_table = &axp20x_writeable_table, + .volatile_table = &axp20x_volatile_table, + .max_register = AXP20X_FG_RES, + .cache_type = REGCACHE_RBTREE, +}; + +#define AXP20X_IRQ(_irq, _off, _mask) \ + [AXP20X_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) } + +static const struct regmap_irq axp20x_regmap_irqs[] = { + AXP20X_IRQ(ACIN_OVER_V, 0, 7), + AXP20X_IRQ(ACIN_PLUGIN, 0, 6), + AXP20X_IRQ(ACIN_REMOVAL, 0, 5), + AXP20X_IRQ(VBUS_OVER_V, 0, 4), + AXP20X_IRQ(VBUS_PLUGIN, 0, 3), + AXP20X_IRQ(VBUS_REMOVAL, 0, 2), + AXP20X_IRQ(VBUS_V_LOW, 0, 1), + AXP20X_IRQ(BATT_PLUGIN, 1, 7), + AXP20X_IRQ(BATT_REMOVAL, 1, 6), + AXP20X_IRQ(BATT_ENT_ACT_MODE, 1, 5), + AXP20X_IRQ(BATT_EXIT_ACT_MODE, 1, 4), + AXP20X_IRQ(CHARG, 1, 3), + AXP20X_IRQ(CHARG_DONE, 1, 2), + AXP20X_IRQ(BATT_TEMP_HIGH, 1, 1), + AXP20X_IRQ(BATT_TEMP_LOW, 1, 0), + AXP20X_IRQ(DIE_TEMP_HIGH, 2, 7), + AXP20X_IRQ(CHARG_I_LOW, 2, 6), + AXP20X_IRQ(DCDC1_V_LONG, 2, 5), + AXP20X_IRQ(DCDC2_V_LONG, 2, 4), + AXP20X_IRQ(DCDC3_V_LONG, 2, 3), + AXP20X_IRQ(PEK_SHORT, 2, 1), + AXP20X_IRQ(PEK_LONG, 2, 0), + AXP20X_IRQ(N_OE_PWR_ON, 3, 7), + AXP20X_IRQ(N_OE_PWR_OFF, 3, 6), + AXP20X_IRQ(VBUS_VALID, 3, 5), + AXP20X_IRQ(VBUS_NOT_VALID, 3, 4), + AXP20X_IRQ(VBUS_SESS_VALID, 3, 3), + AXP20X_IRQ(VBUS_SESS_END, 3, 2), + AXP20X_IRQ(LOW_PWR_LVL1, 3, 1), + AXP20X_IRQ(LOW_PWR_LVL2, 3, 0), + AXP20X_IRQ(TIMER, 4, 7), + AXP20X_IRQ(PEK_RIS_EDGE, 4, 6), + AXP20X_IRQ(PEK_FAL_EDGE, 4, 5), + AXP20X_IRQ(GPIO3_INPUT, 4, 3), + AXP20X_IRQ(GPIO2_INPUT, 4, 2), + AXP20X_IRQ(GPIO1_INPUT, 4, 1), + AXP20X_IRQ(GPIO0_INPUT, 4, 0), +}; + +static const struct of_device_id axp20x_of_match[] = { + { .compatible = "x-powers,axp202", .data = (void *) AXP202_ID }, + { .compatible = "x-powers,axp209", .data = (void *) AXP209_ID }, + { }, +}; +MODULE_DEVICE_TABLE(of, axp20x_of_match); + +/* + * This is useless for OF-enabled devices, but it is needed by I2C subsystem + */ +static const struct i2c_device_id axp20x_i2c_id[] = { + { }, +}; +MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id); + +static const struct regmap_irq_chip axp20x_regmap_irq_chip = { + .name = "axp20x_irq_chip", + .status_base = AXP20X_IRQ1_STATE, + .ack_base = AXP20X_IRQ1_STATE, + .mask_base = AXP20X_IRQ1_EN, + .num_regs = 5, + .irqs = axp20x_regmap_irqs, + .num_irqs = ARRAY_SIZE(axp20x_regmap_irqs), + .mask_invert = true, + .init_ack_masked = true, +}; + +static const char * const axp20x_supplies[] = { + "acin", + "vin2", + "vin3", + "ldo24in", + "ldo3in", + "ldo5in", +}; + +static struct mfd_cell axp20x_cells[] = { + { + .name = "axp20x-pek", + .num_resources = ARRAY_SIZE(axp20x_pek_resources), + .resources = axp20x_pek_resources, + }, { + .name = "axp20x-regulator", + .parent_supplies = axp20x_supplies, + .num_parent_supplies = ARRAY_SIZE(axp20x_supplies), + }, +}; + +static struct axp20x_dev *axp20x_pm_power_off; +static void axp20x_power_off(void) +{ + regmap_write(axp20x_pm_power_off->regmap, AXP20X_OFF_CTRL, + AXP20X_OFF); +} + +static int axp20x_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct axp20x_dev *axp20x; + const struct of_device_id *of_id; + int ret; + + axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL); + if (!axp20x) + return -ENOMEM; + + of_id = of_match_device(axp20x_of_match, &i2c->dev); + if (!of_id) { + dev_err(&i2c->dev, "Unable to setup AXP20X data\n"); + return -ENODEV; + } + axp20x->variant = (long) of_id->data; + + axp20x->i2c_client = i2c; + axp20x->dev = &i2c->dev; + dev_set_drvdata(axp20x->dev, axp20x); + + axp20x->regmap = devm_regmap_init_i2c(i2c, &axp20x_regmap_config); + if (IS_ERR(axp20x->regmap)) { + ret = PTR_ERR(axp20x->regmap); + dev_err(&i2c->dev, "regmap init failed: %d\n", ret); + return ret; + } + + ret = regmap_add_irq_chip(axp20x->regmap, i2c->irq, + IRQF_ONESHOT | IRQF_SHARED, -1, + &axp20x_regmap_irq_chip, + &axp20x->regmap_irqc); + if (ret) { + dev_err(&i2c->dev, "failed to add irq chip: %d\n", ret); + return ret; + } + + ret = mfd_add_devices(axp20x->dev, -1, axp20x_cells, + ARRAY_SIZE(axp20x_cells), NULL, 0, NULL); + + if (ret) { + dev_err(&i2c->dev, "failed to add MFD devices: %d\n", ret); + regmap_del_irq_chip(i2c->irq, axp20x->regmap_irqc); + return ret; + } + + if (!pm_power_off) { + axp20x_pm_power_off = axp20x; + pm_power_off = axp20x_power_off; + } + + dev_info(&i2c->dev, "AXP20X driver loaded\n"); + + return 0; +} + +static int axp20x_i2c_remove(struct i2c_client *i2c) +{ + struct axp20x_dev *axp20x = i2c_get_clientdata(i2c); + + if (axp20x == axp20x_pm_power_off) { + axp20x_pm_power_off = NULL; + pm_power_off = NULL; + } + + mfd_remove_devices(axp20x->dev); + regmap_del_irq_chip(axp20x->i2c_client->irq, axp20x->regmap_irqc); + + return 0; +} + +static struct i2c_driver axp20x_i2c_driver = { + .driver = { + .name = "axp20x", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(axp20x_of_match), + }, + .probe = axp20x_i2c_probe, + .remove = axp20x_i2c_remove, + .id_table = axp20x_i2c_id, +}; + +module_i2c_driver(axp20x_i2c_driver); + +MODULE_DESCRIPTION("PMIC MFD core driver for AXP20X"); +MODULE_AUTHOR("Carlo Caione <carlo@caione.org>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mfd/bcm590xx.c b/drivers/mfd/bcm590xx.c index 43cba1a1973c..e334de000e8c 100644 --- a/drivers/mfd/bcm590xx.c +++ b/drivers/mfd/bcm590xx.c @@ -96,6 +96,12 @@ err: return ret; } +static int bcm590xx_i2c_remove(struct i2c_client *i2c) +{ + mfd_remove_devices(&i2c->dev); + return 0; +} + static const struct of_device_id bcm590xx_of_match[] = { { .compatible = "brcm,bcm59056" }, { } @@ -115,6 +121,7 @@ static struct i2c_driver bcm590xx_i2c_driver = { .of_match_table = of_match_ptr(bcm590xx_of_match), }, .probe = bcm590xx_i2c_probe, + .remove = bcm590xx_i2c_remove, .id_table = bcm590xx_i2c_id, }; module_i2c_driver(bcm590xx_i2c_driver); @@ -122,4 +129,4 @@ module_i2c_driver(bcm590xx_i2c_driver); MODULE_AUTHOR("Matt Porter <mporter@linaro.org>"); MODULE_DESCRIPTION("BCM590xx multi-function driver"); MODULE_LICENSE("GPL v2"); -MODULE_ALIAS("platform:bcm590xx"); +MODULE_ALIAS("i2c:bcm590xx"); diff --git a/drivers/mfd/cros_ec.c b/drivers/mfd/cros_ec.c index 783fe2e73e1e..38fe9bf0d169 100644 --- a/drivers/mfd/cros_ec.c +++ b/drivers/mfd/cros_ec.c @@ -30,7 +30,7 @@ int cros_ec_prepare_tx(struct cros_ec_device *ec_dev, uint8_t *out; int csum, i; - BUG_ON(msg->out_len > EC_HOST_PARAM_SIZE); + BUG_ON(msg->out_len > EC_PROTO2_MAX_PARAM_SIZE); out = ec_dev->dout; out[0] = EC_CMD_VERSION0 + msg->version; out[1] = msg->cmd; @@ -90,6 +90,11 @@ static const struct mfd_cell cros_devs[] = { .id = 1, .of_compatible = "google,cros-ec-keyb", }, + { + .name = "cros-ec-i2c-tunnel", + .id = 2, + .of_compatible = "google,cros-ec-i2c-tunnel", + }, }; int cros_ec_register(struct cros_ec_device *ec_dev) @@ -184,3 +189,6 @@ int cros_ec_resume(struct cros_ec_device *ec_dev) EXPORT_SYMBOL(cros_ec_resume); #endif + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("ChromeOS EC core driver"); diff --git a/drivers/mfd/cros_ec_spi.c b/drivers/mfd/cros_ec_spi.c index 84af8d7a4295..0b8d32829166 100644 --- a/drivers/mfd/cros_ec_spi.c +++ b/drivers/mfd/cros_ec_spi.c @@ -39,14 +39,22 @@ #define EC_MSG_PREAMBLE_COUNT 32 /* - * We must get a response from the EC in 5ms. This is a very long - * time, but the flash write command can take 2-3ms. The EC command - * processing is currently not very fast (about 500us). We could - * look at speeding this up and making the flash write command a - * 'slow' command, requiring a GET_STATUS wait loop, like flash - * erase. - */ -#define EC_MSG_DEADLINE_MS 5 + * Allow for a long time for the EC to respond. We support i2c + * tunneling and support fairly long messages for the tunnel (249 + * bytes long at the moment). If we're talking to a 100 kHz device + * on the other end and need to transfer ~256 bytes, then we need: + * 10 us/bit * ~10 bits/byte * ~256 bytes = ~25ms + * + * We'll wait 4 times that to handle clock stretching and other + * paranoia. + * + * It's pretty unlikely that we'll really see a 249 byte tunnel in + * anything other than testing. If this was more common we might + * consider having slow commands like this require a GET_STATUS + * wait loop. The 'flash write' command would be another candidate + * for this, clocking in at 2-3ms. + */ +#define EC_MSG_DEADLINE_MS 100 /* * Time between raising the SPI chip select (for the end of a @@ -65,11 +73,13 @@ * if no record * @end_of_msg_delay: used to set the delay_usecs on the spi_transfer that * is sent when we want to turn off CS at the end of a transaction. + * @lock: mutex to ensure only one user of cros_ec_command_spi_xfer at a time */ struct cros_ec_spi { struct spi_device *spi; s64 last_transfer_ns; unsigned int end_of_msg_delay; + struct mutex lock; }; static void debug_packet(struct device *dev, const char *name, u8 *ptr, @@ -111,7 +121,9 @@ static int cros_ec_spi_receive_response(struct cros_ec_device *ec_dev, /* Receive data until we see the header byte */ deadline = jiffies + msecs_to_jiffies(EC_MSG_DEADLINE_MS); - do { + while (true) { + unsigned long start_jiffies = jiffies; + memset(&trans, 0, sizeof(trans)); trans.cs_change = 1; trans.rx_buf = ptr = ec_dev->din; @@ -132,12 +144,19 @@ static int cros_ec_spi_receive_response(struct cros_ec_device *ec_dev, break; } } + if (ptr != end) + break; - if (time_after(jiffies, deadline)) { + /* + * Use the time at the start of the loop as a timeout. This + * gives us one last shot at getting the transfer and is useful + * in case we got context switched out for a while. + */ + if (time_after(start_jiffies, deadline)) { dev_warn(ec_dev->dev, "EC failed to respond in time\n"); return -ETIMEDOUT; } - } while (ptr == end); + } /* * ptr now points to the header byte. Copy any valid data to the @@ -208,6 +227,13 @@ static int cros_ec_command_spi_xfer(struct cros_ec_device *ec_dev, int ret = 0, final_ret; struct timespec ts; + /* + * We have the shared ec_dev buffer plus we do lots of separate spi_sync + * calls, so we need to make sure only one person is using this at a + * time. + */ + mutex_lock(&ec_spi->lock); + len = cros_ec_prepare_tx(ec_dev, ec_msg); dev_dbg(ec_dev->dev, "prepared, len=%d\n", len); @@ -219,7 +245,7 @@ static int cros_ec_command_spi_xfer(struct cros_ec_device *ec_dev, ktime_get_ts(&ts); delay = timespec_to_ns(&ts) - ec_spi->last_transfer_ns; if (delay < EC_SPI_RECOVERY_TIME_NS) - ndelay(delay); + ndelay(EC_SPI_RECOVERY_TIME_NS - delay); } /* Transmit phase - send our message */ @@ -260,7 +286,7 @@ static int cros_ec_command_spi_xfer(struct cros_ec_device *ec_dev, ret = final_ret; if (ret < 0) { dev_err(ec_dev->dev, "spi transfer failed: %d\n", ret); - return ret; + goto exit; } /* check response error code */ @@ -269,14 +295,16 @@ static int cros_ec_command_spi_xfer(struct cros_ec_device *ec_dev, dev_warn(ec_dev->dev, "command 0x%02x returned an error %d\n", ec_msg->cmd, ptr[0]); debug_packet(ec_dev->dev, "in_err", ptr, len); - return -EINVAL; + ret = -EINVAL; + goto exit; } len = ptr[1]; sum = ptr[0] + ptr[1]; if (len > ec_msg->in_len) { dev_err(ec_dev->dev, "packet too long (%d bytes, expected %d)", len, ec_msg->in_len); - return -ENOSPC; + ret = -ENOSPC; + goto exit; } /* copy response packet payload and compute checksum */ @@ -293,10 +321,14 @@ static int cros_ec_command_spi_xfer(struct cros_ec_device *ec_dev, dev_err(ec_dev->dev, "bad packet checksum, expected %02x, got %02x\n", sum, ptr[len + 2]); - return -EBADMSG; + ret = -EBADMSG; + goto exit; } - return 0; + ret = 0; +exit: + mutex_unlock(&ec_spi->lock); + return ret; } static void cros_ec_spi_dt_probe(struct cros_ec_spi *ec_spi, struct device *dev) @@ -327,6 +359,7 @@ static int cros_ec_spi_probe(struct spi_device *spi) if (ec_spi == NULL) return -ENOMEM; ec_spi->spi = spi; + mutex_init(&ec_spi->lock); ec_dev = devm_kzalloc(dev, sizeof(*ec_dev), GFP_KERNEL); if (!ec_dev) return -ENOMEM; diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c index 7694e0700d34..193cf168ba84 100644 --- a/drivers/mfd/db8500-prcmu.c +++ b/drivers/mfd/db8500-prcmu.c @@ -1734,18 +1734,17 @@ static struct cpufreq_frequency_table db8500_cpufreq_table[] = { static long round_armss_rate(unsigned long rate) { + struct cpufreq_frequency_table *pos; long freq = 0; - int i = 0; /* cpufreq table frequencies is in KHz. */ rate = rate / 1000; /* Find the corresponding arm opp from the cpufreq table. */ - while (db8500_cpufreq_table[i].frequency != CPUFREQ_TABLE_END) { - freq = db8500_cpufreq_table[i].frequency; + cpufreq_for_each_entry(pos, db8500_cpufreq_table) { + freq = pos->frequency; if (freq == rate) break; - i++; } /* Return the last valid value, even if a match was not found. */ @@ -1886,23 +1885,21 @@ static void set_clock_rate(u8 clock, unsigned long rate) static int set_armss_rate(unsigned long rate) { - int i = 0; + struct cpufreq_frequency_table *pos; /* cpufreq table frequencies is in KHz. */ rate = rate / 1000; /* Find the corresponding arm opp from the cpufreq table. */ - while (db8500_cpufreq_table[i].frequency != CPUFREQ_TABLE_END) { - if (db8500_cpufreq_table[i].frequency == rate) + cpufreq_for_each_entry(pos, db8500_cpufreq_table) + if (pos->frequency == rate) break; - i++; - } - if (db8500_cpufreq_table[i].frequency != rate) + if (pos->frequency != rate) return -EINVAL; /* Set the new arm opp. */ - return db8500_prcmu_set_arm_opp(db8500_cpufreq_table[i].driver_data); + return db8500_prcmu_set_arm_opp(pos->driver_data); } static int set_plldsi_rate(unsigned long rate) @@ -2303,9 +2300,6 @@ int prcmu_ac_wake_req(void) if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work, msecs_to_jiffies(5000))) { -#if defined(CONFIG_DBX500_PRCMU_DEBUG) - db8500_prcmu_debug_dump(__func__, true, true); -#endif pr_crit("prcmu: %s timed out (5 s) waiting for a reply.\n", __func__); ret = -EFAULT; @@ -3115,7 +3109,7 @@ static int db8500_prcmu_register_ab8500(struct device *parent, { struct device_node *np; struct resource ab8500_resource; - struct mfd_cell ab8500_cell = { + const struct mfd_cell ab8500_cell = { .name = "ab8500-core", .of_compatible = "stericsson,ab8500", .id = AB8500_VERSION_AB8500, diff --git a/drivers/mfd/ipaq-micro.c b/drivers/mfd/ipaq-micro.c new file mode 100644 index 000000000000..7e50fe0118e3 --- /dev/null +++ b/drivers/mfd/ipaq-micro.c @@ -0,0 +1,482 @@ +/* + * Compaq iPAQ h3xxx Atmel microcontroller companion support + * + * This is an Atmel AT90LS8535 with a special flashed-in firmware that + * implements the special protocol used by this driver. + * + * based on previous kernel 2.4 version by Andrew Christian + * Author : Alessandro Gardich <gremlin@gremlin.it> + * Author : Dmitry Artamonow <mad_soft@inbox.ru> + * Author : Linus Walleij <linus.walleij@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/pm.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/mfd/core.h> +#include <linux/mfd/ipaq-micro.h> +#include <linux/string.h> +#include <linux/random.h> +#include <linux/slab.h> +#include <linux/list.h> + +#include <mach/hardware.h> + +static void ipaq_micro_trigger_tx(struct ipaq_micro *micro) +{ + struct ipaq_micro_txdev *tx = µ->tx; + struct ipaq_micro_msg *msg = micro->msg; + int i, bp; + u8 checksum; + u32 val; + + bp = 0; + tx->buf[bp++] = CHAR_SOF; + + checksum = ((msg->id & 0x0f) << 4) | (msg->tx_len & 0x0f); + tx->buf[bp++] = checksum; + + for (i = 0; i < msg->tx_len; i++) { + tx->buf[bp++] = msg->tx_data[i]; + checksum += msg->tx_data[i]; + } + + tx->buf[bp++] = checksum; + tx->len = bp; + tx->index = 0; + print_hex_dump(KERN_DEBUG, "data: ", DUMP_PREFIX_OFFSET, 16, 1, + tx->buf, tx->len, true); + + /* Enable interrupt */ + val = readl(micro->base + UTCR3); + val |= UTCR3_TIE; + writel(val, micro->base + UTCR3); +} + +int ipaq_micro_tx_msg(struct ipaq_micro *micro, struct ipaq_micro_msg *msg) +{ + unsigned long flags; + + dev_dbg(micro->dev, "TX msg: %02x, %d bytes\n", msg->id, msg->tx_len); + + spin_lock_irqsave(µ->lock, flags); + if (micro->msg) { + list_add_tail(&msg->node, µ->queue); + spin_unlock_irqrestore(µ->lock, flags); + return 0; + } + micro->msg = msg; + ipaq_micro_trigger_tx(micro); + spin_unlock_irqrestore(µ->lock, flags); + return 0; +} +EXPORT_SYMBOL(ipaq_micro_tx_msg); + +static void micro_rx_msg(struct ipaq_micro *micro, u8 id, int len, u8 *data) +{ + int i; + + dev_dbg(micro->dev, "RX msg: %02x, %d bytes\n", id, len); + + spin_lock(µ->lock); + switch (id) { + case MSG_VERSION: + case MSG_EEPROM_READ: + case MSG_EEPROM_WRITE: + case MSG_BACKLIGHT: + case MSG_NOTIFY_LED: + case MSG_THERMAL_SENSOR: + case MSG_BATTERY: + /* Handle synchronous messages */ + if (micro->msg && micro->msg->id == id) { + struct ipaq_micro_msg *msg = micro->msg; + + memcpy(msg->rx_data, data, len); + msg->rx_len = len; + complete(µ->msg->ack); + if (!list_empty(µ->queue)) { + micro->msg = list_entry(micro->queue.next, + struct ipaq_micro_msg, + node); + list_del_init(µ->msg->node); + ipaq_micro_trigger_tx(micro); + } else + micro->msg = NULL; + dev_dbg(micro->dev, "OK RX message 0x%02x\n", id); + } else { + dev_err(micro->dev, + "out of band RX message 0x%02x\n", id); + if(!micro->msg) + dev_info(micro->dev, "no message queued\n"); + else + dev_info(micro->dev, "expected message %02x\n", + micro->msg->id); + } + break; + case MSG_KEYBOARD: + if (micro->key) + micro->key(micro->key_data, len, data); + else + dev_dbg(micro->dev, "key message ignored, no handle \n"); + break; + case MSG_TOUCHSCREEN: + if (micro->ts) + micro->ts(micro->ts_data, len, data); + else + dev_dbg(micro->dev, "touchscreen message ignored, no handle \n"); + break; + default: + dev_err(micro->dev, + "unknown msg %d [%d] ", id, len); + for (i = 0; i < len; ++i) + pr_cont("0x%02x ", data[i]); + pr_cont("\n"); + } + spin_unlock(µ->lock); +} + +static void micro_process_char(struct ipaq_micro *micro, u8 ch) +{ + struct ipaq_micro_rxdev *rx = µ->rx; + + switch (rx->state) { + case STATE_SOF: /* Looking for SOF */ + if (ch == CHAR_SOF) + rx->state = STATE_ID; /* Next byte is the id and len */ + break; + case STATE_ID: /* Looking for id and len byte */ + rx->id = (ch & 0xf0) >> 4 ; + rx->len = (ch & 0x0f); + rx->index = 0; + rx->chksum = ch; + rx->state = (rx->len > 0) ? STATE_DATA : STATE_CHKSUM; + break; + case STATE_DATA: /* Looking for 'len' data bytes */ + rx->chksum += ch; + rx->buf[rx->index] = ch; + if (++rx->index == rx->len) + rx->state = STATE_CHKSUM; + break; + case STATE_CHKSUM: /* Looking for the checksum */ + if (ch == rx->chksum) + micro_rx_msg(micro, rx->id, rx->len, rx->buf); + rx->state = STATE_SOF; + break; + } +} + +static void micro_rx_chars(struct ipaq_micro *micro) +{ + u32 status, ch; + + while ((status = readl(micro->base + UTSR1)) & UTSR1_RNE) { + ch = readl(micro->base + UTDR); + if (status & UTSR1_PRE) + dev_err(micro->dev, "rx: parity error\n"); + else if (status & UTSR1_FRE) + dev_err(micro->dev, "rx: framing error\n"); + else if (status & UTSR1_ROR) + dev_err(micro->dev, "rx: overrun error\n"); + micro_process_char(micro, ch); + } +} + +static void ipaq_micro_get_version(struct ipaq_micro *micro) +{ + struct ipaq_micro_msg msg = { + .id = MSG_VERSION, + }; + + ipaq_micro_tx_msg_sync(micro, &msg); + if (msg.rx_len == 4) { + memcpy(micro->version, msg.rx_data, 4); + micro->version[4] = '\0'; + } else if (msg.rx_len == 9) { + memcpy(micro->version, msg.rx_data, 4); + micro->version[4] = '\0'; + /* Bytes 4-7 are "pack", byte 8 is "boot type" */ + } else { + dev_err(micro->dev, + "illegal version message %d bytes\n", msg.rx_len); + } +} + +static void ipaq_micro_eeprom_read(struct ipaq_micro *micro, + u8 address, u8 len, u8 *data) +{ + struct ipaq_micro_msg msg = { + .id = MSG_EEPROM_READ, + }; + u8 i; + + for (i = 0; i < len; i++) { + msg.tx_data[0] = address + i; + msg.tx_data[1] = 1; + msg.tx_len = 2; + ipaq_micro_tx_msg_sync(micro, &msg); + memcpy(data + (i * 2), msg.rx_data, 2); + } +} + +static char *ipaq_micro_str(u8 *wchar, u8 len) +{ + char retstr[256]; + u8 i; + + for (i = 0; i < len / 2; i++) + retstr[i] = wchar[i * 2]; + return kstrdup(retstr, GFP_KERNEL); +} + +static u16 ipaq_micro_to_u16(u8 *data) +{ + return data[1] << 8 | data[0]; +} + +static void ipaq_micro_eeprom_dump(struct ipaq_micro *micro) +{ + u8 dump[256]; + char *str; + + ipaq_micro_eeprom_read(micro, 0, 128, dump); + str = ipaq_micro_str(dump, 10); + if (str) { + dev_info(micro->dev, "HM version %s\n", str); + kfree(str); + } + str = ipaq_micro_str(dump+10, 40); + if (str) { + dev_info(micro->dev, "serial number: %s\n", str); + /* Feed the random pool with this */ + add_device_randomness(str, strlen(str)); + kfree(str); + } + str = ipaq_micro_str(dump+50, 20); + if (str) { + dev_info(micro->dev, "module ID: %s\n", str); + kfree(str); + } + str = ipaq_micro_str(dump+70, 10); + if (str) { + dev_info(micro->dev, "product revision: %s\n", str); + kfree(str); + } + dev_info(micro->dev, "product ID: %u\n", ipaq_micro_to_u16(dump+80)); + dev_info(micro->dev, "frame rate: %u fps\n", + ipaq_micro_to_u16(dump+82)); + dev_info(micro->dev, "page mode: %u\n", ipaq_micro_to_u16(dump+84)); + dev_info(micro->dev, "country ID: %u\n", ipaq_micro_to_u16(dump+86)); + dev_info(micro->dev, "color display: %s\n", + ipaq_micro_to_u16(dump+88) ? "yes" : "no"); + dev_info(micro->dev, "ROM size: %u MiB\n", ipaq_micro_to_u16(dump+90)); + dev_info(micro->dev, "RAM size: %u KiB\n", ipaq_micro_to_u16(dump+92)); + dev_info(micro->dev, "screen: %u x %u\n", + ipaq_micro_to_u16(dump+94), ipaq_micro_to_u16(dump+96)); + print_hex_dump(KERN_DEBUG, "eeprom: ", DUMP_PREFIX_OFFSET, 16, 1, + dump, 256, true); + +} + +static void micro_tx_chars(struct ipaq_micro *micro) +{ + struct ipaq_micro_txdev *tx = µ->tx; + u32 val; + + while ((tx->index < tx->len) && + (readl(micro->base + UTSR1) & UTSR1_TNF)) { + writel(tx->buf[tx->index], micro->base + UTDR); + tx->index++; + } + + /* Stop interrupts */ + val = readl(micro->base + UTCR3); + val &= ~UTCR3_TIE; + writel(val, micro->base + UTCR3); +} + +static void micro_reset_comm(struct ipaq_micro *micro) +{ + struct ipaq_micro_rxdev *rx = µ->rx; + u32 val; + + if (micro->msg) + complete(µ->msg->ack); + + /* Initialize Serial channel protocol frame */ + rx->state = STATE_SOF; /* Reset the state machine */ + + /* Set up interrupts */ + writel(0x01, micro->sdlc + 0x0); /* Select UART mode */ + + /* Clean up CR3 */ + writel(0x0, micro->base + UTCR3); + + /* Format: 8N1 */ + writel(UTCR0_8BitData | UTCR0_1StpBit, micro->base + UTCR0); + + /* Baud rate: 115200 */ + writel(0x0, micro->base + UTCR1); + writel(0x1, micro->base + UTCR2); + + /* Clear SR0 */ + writel(0xff, micro->base + UTSR0); + + /* Enable RX int, disable TX int */ + writel(UTCR3_TXE | UTCR3_RXE | UTCR3_RIE, micro->base + UTCR3); + val = readl(micro->base + UTCR3); + val &= ~UTCR3_TIE; + writel(val, micro->base + UTCR3); +} + +static irqreturn_t micro_serial_isr(int irq, void *dev_id) +{ + struct ipaq_micro *micro = dev_id; + struct ipaq_micro_txdev *tx = µ->tx; + u32 status; + + status = readl(micro->base + UTSR0); + do { + if (status & (UTSR0_RID | UTSR0_RFS)) { + if (status & UTSR0_RID) + /* Clear the Receiver IDLE bit */ + writel(UTSR0_RID, micro->base + UTSR0); + micro_rx_chars(micro); + } + + /* Clear break bits */ + if (status & (UTSR0_RBB | UTSR0_REB)) + writel(status & (UTSR0_RBB | UTSR0_REB), + micro->base + UTSR0); + + if (status & UTSR0_TFS) + micro_tx_chars(micro); + + status = readl(micro->base + UTSR0); + + } while (((tx->index < tx->len) && (status & UTSR0_TFS)) || + (status & (UTSR0_RFS | UTSR0_RID))); + + return IRQ_HANDLED; +} + +static const struct mfd_cell micro_cells[] = { + { .name = "ipaq-micro-backlight", }, + { .name = "ipaq-micro-battery", }, + { .name = "ipaq-micro-keys", }, + { .name = "ipaq-micro-ts", }, + { .name = "ipaq-micro-leds", }, +}; + +static int micro_resume(struct device *dev) +{ + struct ipaq_micro *micro = dev_get_drvdata(dev); + + micro_reset_comm(micro); + mdelay(10); + + return 0; +} + +static int micro_probe(struct platform_device *pdev) +{ + struct ipaq_micro *micro; + struct resource *res; + int ret; + int irq; + + micro = devm_kzalloc(&pdev->dev, sizeof(*micro), GFP_KERNEL); + if (!micro) + return -ENOMEM; + + micro->dev = &pdev->dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -EINVAL; + + micro->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(micro->base)) + return PTR_ERR(micro->base); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!res) + return -EINVAL; + + micro->sdlc = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(micro->sdlc)) + return PTR_ERR(micro->sdlc); + + micro_reset_comm(micro); + + irq = platform_get_irq(pdev, 0); + if (!irq) + return -EINVAL; + ret = devm_request_irq(&pdev->dev, irq, micro_serial_isr, + IRQF_SHARED, "ipaq-micro", + micro); + if (ret) { + dev_err(&pdev->dev, "unable to grab serial port IRQ\n"); + return ret; + } else + dev_info(&pdev->dev, "grabbed serial port IRQ\n"); + + spin_lock_init(µ->lock); + INIT_LIST_HEAD(µ->queue); + platform_set_drvdata(pdev, micro); + + ret = mfd_add_devices(&pdev->dev, pdev->id, micro_cells, + ARRAY_SIZE(micro_cells), NULL, 0, NULL); + if (ret) { + dev_err(&pdev->dev, "error adding MFD cells"); + return ret; + } + + /* Check version */ + ipaq_micro_get_version(micro); + dev_info(&pdev->dev, "Atmel micro ASIC version %s\n", micro->version); + ipaq_micro_eeprom_dump(micro); + + return 0; +} + +static int micro_remove(struct platform_device *pdev) +{ + struct ipaq_micro *micro = platform_get_drvdata(pdev); + u32 val; + + mfd_remove_devices(&pdev->dev); + + val = readl(micro->base + UTCR3); + val &= ~(UTCR3_RXE | UTCR3_RIE); /* disable receive interrupt */ + val &= ~(UTCR3_TXE | UTCR3_TIE); /* disable transmit interrupt */ + writel(val, micro->base + UTCR3); + + return 0; +} + +static const struct dev_pm_ops micro_dev_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(NULL, micro_resume) +}; + +static struct platform_driver micro_device_driver = { + .driver = { + .name = "ipaq-h3xxx-micro", + .pm = µ_dev_pm_ops, + }, + .probe = micro_probe, + .remove = micro_remove, + /* .shutdown = micro_suspend, // FIXME */ +}; +module_platform_driver(micro_device_driver); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("driver for iPAQ Atmel micro core and backlight"); diff --git a/drivers/mfd/kempld-core.c b/drivers/mfd/kempld-core.c index 07692604e119..f7ff0188603d 100644 --- a/drivers/mfd/kempld-core.c +++ b/drivers/mfd/kempld-core.c @@ -86,7 +86,7 @@ enum kempld_cells { KEMPLD_UART, }; -static struct mfd_cell kempld_devs[] = { +static const struct mfd_cell kempld_devs[] = { [KEMPLD_I2C] = { .name = "kempld-i2c", }, @@ -288,9 +288,38 @@ EXPORT_SYMBOL_GPL(kempld_release_mutex); */ static int kempld_get_info(struct kempld_device_data *pld) { + int ret; struct kempld_platform_data *pdata = dev_get_platdata(pld->dev); + char major, minor; + + ret = pdata->get_info(pld); + if (ret) + return ret; + + /* The Kontron PLD firmware version string has the following format: + * Pwxy.zzzz + * P: Fixed + * w: PLD number - 1 hex digit + * x: Major version - 1 alphanumerical digit (0-9A-V) + * y: Minor version - 1 alphanumerical digit (0-9A-V) + * zzzz: Build number - 4 zero padded hex digits */ - return pdata->get_info(pld); + if (pld->info.major < 10) + major = pld->info.major + '0'; + else + major = (pld->info.major - 10) + 'A'; + if (pld->info.minor < 10) + minor = pld->info.minor + '0'; + else + minor = (pld->info.minor - 10) + 'A'; + + ret = scnprintf(pld->info.version, sizeof(pld->info.version), + "P%X%c%c.%04X", pld->info.number, major, minor, + pld->info.buildnr); + if (ret < 0) + return ret; + + return 0; } /* @@ -307,9 +336,71 @@ static int kempld_register_cells(struct kempld_device_data *pld) return pdata->register_cells(pld); } +static const char *kempld_get_type_string(struct kempld_device_data *pld) +{ + const char *version_type; + + switch (pld->info.type) { + case 0: + version_type = "release"; + break; + case 1: + version_type = "debug"; + break; + case 2: + version_type = "custom"; + break; + default: + version_type = "unspecified"; + break; + } + + return version_type; +} + +static ssize_t kempld_version_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct kempld_device_data *pld = dev_get_drvdata(dev); + + return scnprintf(buf, PAGE_SIZE, "%s\n", pld->info.version); +} + +static ssize_t kempld_specification_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct kempld_device_data *pld = dev_get_drvdata(dev); + + return scnprintf(buf, PAGE_SIZE, "%d.%d\n", pld->info.spec_major, + pld->info.spec_minor); +} + +static ssize_t kempld_type_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct kempld_device_data *pld = dev_get_drvdata(dev); + + return scnprintf(buf, PAGE_SIZE, "%s\n", kempld_get_type_string(pld)); +} + +static DEVICE_ATTR(pld_version, S_IRUGO, kempld_version_show, NULL); +static DEVICE_ATTR(pld_specification, S_IRUGO, kempld_specification_show, + NULL); +static DEVICE_ATTR(pld_type, S_IRUGO, kempld_type_show, NULL); + +static struct attribute *pld_attributes[] = { + &dev_attr_pld_version.attr, + &dev_attr_pld_specification.attr, + &dev_attr_pld_type.attr, + NULL +}; + +static const struct attribute_group pld_attr_group = { + .attrs = pld_attributes, +}; + static int kempld_detect_device(struct kempld_device_data *pld) { - char *version_type; u8 index_reg; int ret; @@ -335,27 +426,19 @@ static int kempld_detect_device(struct kempld_device_data *pld) if (ret) return ret; - switch (pld->info.type) { - case 0: - version_type = "release"; - break; - case 1: - version_type = "debug"; - break; - case 2: - version_type = "custom"; - break; - default: - version_type = "unspecified"; - } + dev_info(pld->dev, "Found Kontron PLD - %s (%s), spec %d.%d\n", + pld->info.version, kempld_get_type_string(pld), + pld->info.spec_major, pld->info.spec_minor); + + ret = sysfs_create_group(&pld->dev->kobj, &pld_attr_group); + if (ret) + return ret; - dev_info(pld->dev, "Found Kontron PLD %d\n", pld->info.number); - dev_info(pld->dev, "%s version %d.%d build %d, specification %d.%d\n", - version_type, pld->info.major, pld->info.minor, - pld->info.buildnr, pld->info.spec_major, - pld->info.spec_minor); + ret = kempld_register_cells(pld); + if (ret) + sysfs_remove_group(&pld->dev->kobj, &pld_attr_group); - return kempld_register_cells(pld); + return ret; } static int kempld_probe(struct platform_device *pdev) @@ -399,6 +482,8 @@ static int kempld_remove(struct platform_device *pdev) struct kempld_device_data *pld = platform_get_drvdata(pdev); struct kempld_platform_data *pdata = dev_get_platdata(pld->dev); + sysfs_remove_group(&pld->dev->kobj, &pld_attr_group); + mfd_remove_devices(&pdev->dev); pdata->release_hardware_mutex(pld); diff --git a/drivers/mfd/lp3943.c b/drivers/mfd/lp3943.c index e32226836fb4..335b930112b2 100644 --- a/drivers/mfd/lp3943.c +++ b/drivers/mfd/lp3943.c @@ -62,7 +62,7 @@ static const struct lp3943_reg_cfg lp3943_mux_cfg[] = { { LP3943_REG_MUX3, 0xC0, 6 }, }; -static struct mfd_cell lp3943_devs[] = { +static const struct mfd_cell lp3943_devs[] = { { .name = "lp3943-pwm", .of_compatible = "ti,lp3943-pwm", diff --git a/drivers/mfd/lpc_ich.c b/drivers/mfd/lpc_ich.c index 3f10ea3f45d1..7d8482ff5868 100644 --- a/drivers/mfd/lpc_ich.c +++ b/drivers/mfd/lpc_ich.c @@ -488,6 +488,7 @@ static struct lpc_ich_info lpc_chipset_info[] = { [LPC_PPT] = { .name = "Panther Point", .iTCO_version = 2, + .gpio_version = ICH_V5_GPIO, }, [LPC_LPT] = { .name = "Lynx Point", diff --git a/drivers/mfd/max14577.c b/drivers/mfd/max14577.c index 5f13cefe8def..4a5e885383f8 100644 --- a/drivers/mfd/max14577.c +++ b/drivers/mfd/max14577.c @@ -1,7 +1,7 @@ /* - * max14577.c - mfd core driver for the Maxim 14577 + * max14577.c - mfd core driver for the Maxim 14577/77836 * - * Copyright (C) 2013 Samsung Electrnoics + * Copyright (C) 2014 Samsung Electrnoics * Chanwoo Choi <cw00.choi@samsung.com> * Krzysztof Kozlowski <k.kozlowski@samsung.com> * @@ -21,11 +21,12 @@ #include <linux/err.h> #include <linux/module.h> #include <linux/interrupt.h> +#include <linux/of_device.h> #include <linux/mfd/core.h> #include <linux/mfd/max14577.h> #include <linux/mfd/max14577-private.h> -static struct mfd_cell max14577_devs[] = { +static const struct mfd_cell max14577_devs[] = { { .name = "max14577-muic", .of_compatible = "maxim,max14577-muic", @@ -37,7 +38,38 @@ static struct mfd_cell max14577_devs[] = { { .name = "max14577-charger", }, }; -static bool max14577_volatile_reg(struct device *dev, unsigned int reg) +static const struct mfd_cell max77836_devs[] = { + { + .name = "max77836-muic", + .of_compatible = "maxim,max77836-muic", + }, + { + .name = "max77836-regulator", + .of_compatible = "maxim,max77836-regulator", + }, + { + .name = "max77836-charger", + .of_compatible = "maxim,max77836-charger", + }, + { + .name = "max77836-battery", + .of_compatible = "maxim,max77836-battery", + }, +}; + +static const struct of_device_id max14577_dt_match[] = { + { + .compatible = "maxim,max14577", + .data = (void *)MAXIM_DEVICE_TYPE_MAX14577, + }, + { + .compatible = "maxim,max77836", + .data = (void *)MAXIM_DEVICE_TYPE_MAX77836, + }, + {}, +}; + +static bool max14577_muic_volatile_reg(struct device *dev, unsigned int reg) { switch (reg) { case MAX14577_REG_INT1 ... MAX14577_REG_STATUS3: @@ -48,49 +80,221 @@ static bool max14577_volatile_reg(struct device *dev, unsigned int reg) return false; } -static const struct regmap_config max14577_regmap_config = { +static bool max77836_muic_volatile_reg(struct device *dev, unsigned int reg) +{ + /* Any max14577 volatile registers are also max77836 volatile. */ + if (max14577_muic_volatile_reg(dev, reg)) + return true; + + switch (reg) { + case MAX77836_FG_REG_VCELL_MSB ... MAX77836_FG_REG_SOC_LSB: + case MAX77836_FG_REG_CRATE_MSB ... MAX77836_FG_REG_CRATE_LSB: + case MAX77836_FG_REG_STATUS_H ... MAX77836_FG_REG_STATUS_L: + case MAX77836_PMIC_REG_INTSRC: + case MAX77836_PMIC_REG_TOPSYS_INT: + case MAX77836_PMIC_REG_TOPSYS_STAT: + return true; + default: + break; + } + return false; +} + +static const struct regmap_config max14577_muic_regmap_config = { .reg_bits = 8, .val_bits = 8, - .volatile_reg = max14577_volatile_reg, + .volatile_reg = max14577_muic_volatile_reg, .max_register = MAX14577_REG_END, }; +static const struct regmap_config max77836_pmic_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .volatile_reg = max77836_muic_volatile_reg, + .max_register = MAX77836_PMIC_REG_END, +}; + static const struct regmap_irq max14577_irqs[] = { /* INT1 interrupts */ - { .reg_offset = 0, .mask = INT1_ADC_MASK, }, - { .reg_offset = 0, .mask = INT1_ADCLOW_MASK, }, - { .reg_offset = 0, .mask = INT1_ADCERR_MASK, }, + { .reg_offset = 0, .mask = MAX14577_INT1_ADC_MASK, }, + { .reg_offset = 0, .mask = MAX14577_INT1_ADCLOW_MASK, }, + { .reg_offset = 0, .mask = MAX14577_INT1_ADCERR_MASK, }, /* INT2 interrupts */ - { .reg_offset = 1, .mask = INT2_CHGTYP_MASK, }, - { .reg_offset = 1, .mask = INT2_CHGDETRUN_MASK, }, - { .reg_offset = 1, .mask = INT2_DCDTMR_MASK, }, - { .reg_offset = 1, .mask = INT2_DBCHG_MASK, }, - { .reg_offset = 1, .mask = INT2_VBVOLT_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_CHGTYP_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_CHGDETRUN_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_DCDTMR_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_DBCHG_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_VBVOLT_MASK, }, /* INT3 interrupts */ - { .reg_offset = 2, .mask = INT3_EOC_MASK, }, - { .reg_offset = 2, .mask = INT3_CGMBC_MASK, }, - { .reg_offset = 2, .mask = INT3_OVP_MASK, }, - { .reg_offset = 2, .mask = INT3_MBCCHGERR_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_EOC_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_CGMBC_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_OVP_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_MBCCHGERR_MASK, }, }; static const struct regmap_irq_chip max14577_irq_chip = { .name = "max14577", .status_base = MAX14577_REG_INT1, .mask_base = MAX14577_REG_INTMASK1, - .mask_invert = 1, + .mask_invert = true, .num_regs = 3, .irqs = max14577_irqs, .num_irqs = ARRAY_SIZE(max14577_irqs), }; +static const struct regmap_irq max77836_muic_irqs[] = { + /* INT1 interrupts */ + { .reg_offset = 0, .mask = MAX14577_INT1_ADC_MASK, }, + { .reg_offset = 0, .mask = MAX14577_INT1_ADCLOW_MASK, }, + { .reg_offset = 0, .mask = MAX14577_INT1_ADCERR_MASK, }, + { .reg_offset = 0, .mask = MAX77836_INT1_ADC1K_MASK, }, + /* INT2 interrupts */ + { .reg_offset = 1, .mask = MAX14577_INT2_CHGTYP_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_CHGDETRUN_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_DCDTMR_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_DBCHG_MASK, }, + { .reg_offset = 1, .mask = MAX14577_INT2_VBVOLT_MASK, }, + { .reg_offset = 1, .mask = MAX77836_INT2_VIDRM_MASK, }, + /* INT3 interrupts */ + { .reg_offset = 2, .mask = MAX14577_INT3_EOC_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_CGMBC_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_OVP_MASK, }, + { .reg_offset = 2, .mask = MAX14577_INT3_MBCCHGERR_MASK, }, +}; + +static const struct regmap_irq_chip max77836_muic_irq_chip = { + .name = "max77836-muic", + .status_base = MAX14577_REG_INT1, + .mask_base = MAX14577_REG_INTMASK1, + .mask_invert = true, + .num_regs = 3, + .irqs = max77836_muic_irqs, + .num_irqs = ARRAY_SIZE(max77836_muic_irqs), +}; + +static const struct regmap_irq max77836_pmic_irqs[] = { + { .reg_offset = 0, .mask = MAX77836_TOPSYS_INT_T120C_MASK, }, + { .reg_offset = 0, .mask = MAX77836_TOPSYS_INT_T140C_MASK, }, +}; + +static const struct regmap_irq_chip max77836_pmic_irq_chip = { + .name = "max77836-pmic", + .status_base = MAX77836_PMIC_REG_TOPSYS_INT, + .mask_base = MAX77836_PMIC_REG_TOPSYS_INT_MASK, + .mask_invert = false, + .num_regs = 1, + .irqs = max77836_pmic_irqs, + .num_irqs = ARRAY_SIZE(max77836_pmic_irqs), +}; + +static void max14577_print_dev_type(struct max14577 *max14577) +{ + u8 reg_data, vendor_id, device_id; + int ret; + + ret = max14577_read_reg(max14577->regmap, MAX14577_REG_DEVICEID, + ®_data); + if (ret) { + dev_err(max14577->dev, + "Failed to read DEVICEID register: %d\n", ret); + return; + } + + vendor_id = ((reg_data & DEVID_VENDORID_MASK) >> + DEVID_VENDORID_SHIFT); + device_id = ((reg_data & DEVID_DEVICEID_MASK) >> + DEVID_DEVICEID_SHIFT); + + dev_info(max14577->dev, "Device type: %u (ID: 0x%x, vendor: 0x%x)\n", + max14577->dev_type, device_id, vendor_id); +} + +/* + * Max77836 specific initialization code for driver probe. + * Adds new I2C dummy device, regmap and regmap IRQ chip. + * Unmasks Interrupt Source register. + * + * On success returns 0. + * On failure returns errno and reverts any changes done so far (e.g. remove + * I2C dummy device), except masking the INT SRC register. + */ +static int max77836_init(struct max14577 *max14577) +{ + int ret; + u8 intsrc_mask; + + max14577->i2c_pmic = i2c_new_dummy(max14577->i2c->adapter, + I2C_ADDR_PMIC); + if (!max14577->i2c_pmic) { + dev_err(max14577->dev, "Failed to register PMIC I2C device\n"); + return -ENODEV; + } + i2c_set_clientdata(max14577->i2c_pmic, max14577); + + max14577->regmap_pmic = devm_regmap_init_i2c(max14577->i2c_pmic, + &max77836_pmic_regmap_config); + if (IS_ERR(max14577->regmap_pmic)) { + ret = PTR_ERR(max14577->regmap_pmic); + dev_err(max14577->dev, "Failed to allocate PMIC register map: %d\n", + ret); + goto err; + } + + /* Un-mask MAX77836 Interrupt Source register */ + ret = max14577_read_reg(max14577->regmap_pmic, + MAX77836_PMIC_REG_INTSRC_MASK, &intsrc_mask); + if (ret < 0) { + dev_err(max14577->dev, "Failed to read PMIC register\n"); + goto err; + } + + intsrc_mask &= ~(MAX77836_INTSRC_MASK_TOP_INT_MASK); + intsrc_mask &= ~(MAX77836_INTSRC_MASK_MUIC_CHG_INT_MASK); + ret = max14577_write_reg(max14577->regmap_pmic, + MAX77836_PMIC_REG_INTSRC_MASK, intsrc_mask); + if (ret < 0) { + dev_err(max14577->dev, "Failed to write PMIC register\n"); + goto err; + } + + ret = regmap_add_irq_chip(max14577->regmap_pmic, max14577->irq, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT | IRQF_SHARED, + 0, &max77836_pmic_irq_chip, + &max14577->irq_data_pmic); + if (ret != 0) { + dev_err(max14577->dev, "Failed to request PMIC IRQ %d: %d\n", + max14577->irq, ret); + goto err; + } + + return 0; + +err: + i2c_unregister_device(max14577->i2c_pmic); + + return ret; +} + +/* + * Max77836 specific de-initialization code for driver remove. + */ +static void max77836_remove(struct max14577 *max14577) +{ + regmap_del_irq_chip(max14577->irq, max14577->irq_data_pmic); + i2c_unregister_device(max14577->i2c_pmic); +} + static int max14577_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { struct max14577 *max14577; struct max14577_platform_data *pdata = dev_get_platdata(&i2c->dev); struct device_node *np = i2c->dev.of_node; - u8 reg_data; int ret = 0; + const struct regmap_irq_chip *irq_chip; + const struct mfd_cell *mfd_devs; + unsigned int mfd_devs_size; + int irq_flags; if (np) { pdata = devm_kzalloc(&i2c->dev, sizeof(*pdata), GFP_KERNEL); @@ -113,7 +317,8 @@ static int max14577_i2c_probe(struct i2c_client *i2c, max14577->i2c = i2c; max14577->irq = i2c->irq; - max14577->regmap = devm_regmap_init_i2c(i2c, &max14577_regmap_config); + max14577->regmap = devm_regmap_init_i2c(i2c, + &max14577_muic_regmap_config); if (IS_ERR(max14577->regmap)) { ret = PTR_ERR(max14577->regmap); dev_err(max14577->dev, "Failed to allocate register map: %d\n", @@ -121,23 +326,37 @@ static int max14577_i2c_probe(struct i2c_client *i2c, return ret; } - ret = max14577_read_reg(max14577->regmap, MAX14577_REG_DEVICEID, - ®_data); - if (ret) { - dev_err(max14577->dev, "Device not found on this channel: %d\n", - ret); - return ret; + if (np) { + const struct of_device_id *of_id; + + of_id = of_match_device(max14577_dt_match, &i2c->dev); + if (of_id) + max14577->dev_type = + (enum maxim_device_type)of_id->data; + } else { + max14577->dev_type = id->driver_data; + } + + max14577_print_dev_type(max14577); + + switch (max14577->dev_type) { + case MAXIM_DEVICE_TYPE_MAX77836: + irq_chip = &max77836_muic_irq_chip; + mfd_devs = max77836_devs; + mfd_devs_size = ARRAY_SIZE(max77836_devs); + irq_flags = IRQF_TRIGGER_FALLING | IRQF_ONESHOT | IRQF_SHARED; + break; + case MAXIM_DEVICE_TYPE_MAX14577: + default: + irq_chip = &max14577_irq_chip; + mfd_devs = max14577_devs; + mfd_devs_size = ARRAY_SIZE(max14577_devs); + irq_flags = IRQF_TRIGGER_FALLING | IRQF_ONESHOT; + break; } - max14577->vendor_id = ((reg_data & DEVID_VENDORID_MASK) >> - DEVID_VENDORID_SHIFT); - max14577->device_id = ((reg_data & DEVID_DEVICEID_MASK) >> - DEVID_DEVICEID_SHIFT); - dev_info(max14577->dev, "Device ID: 0x%x, vendor: 0x%x\n", - max14577->device_id, max14577->vendor_id); ret = regmap_add_irq_chip(max14577->regmap, max14577->irq, - IRQF_TRIGGER_FALLING | IRQF_ONESHOT, 0, - &max14577_irq_chip, + irq_flags, 0, irq_chip, &max14577->irq_data); if (ret != 0) { dev_err(&i2c->dev, "Failed to request IRQ %d: %d\n", @@ -145,8 +364,15 @@ static int max14577_i2c_probe(struct i2c_client *i2c, return ret; } - ret = mfd_add_devices(max14577->dev, -1, max14577_devs, - ARRAY_SIZE(max14577_devs), NULL, 0, + /* Max77836 specific initialization code (additional regmap) */ + if (max14577->dev_type == MAXIM_DEVICE_TYPE_MAX77836) { + ret = max77836_init(max14577); + if (ret < 0) + goto err_max77836; + } + + ret = mfd_add_devices(max14577->dev, -1, mfd_devs, + mfd_devs_size, NULL, 0, regmap_irq_get_domain(max14577->irq_data)); if (ret < 0) goto err_mfd; @@ -156,6 +382,9 @@ static int max14577_i2c_probe(struct i2c_client *i2c, return 0; err_mfd: + if (max14577->dev_type == MAXIM_DEVICE_TYPE_MAX77836) + max77836_remove(max14577); +err_max77836: regmap_del_irq_chip(max14577->irq, max14577->irq_data); return ret; @@ -167,12 +396,15 @@ static int max14577_i2c_remove(struct i2c_client *i2c) mfd_remove_devices(max14577->dev); regmap_del_irq_chip(max14577->irq, max14577->irq_data); + if (max14577->dev_type == MAXIM_DEVICE_TYPE_MAX77836) + max77836_remove(max14577); return 0; } static const struct i2c_device_id max14577_i2c_id[] = { - { "max14577", 0 }, + { "max14577", MAXIM_DEVICE_TYPE_MAX14577, }, + { "max77836", MAXIM_DEVICE_TYPE_MAX77836, }, { } }; MODULE_DEVICE_TABLE(i2c, max14577_i2c_id); @@ -183,20 +415,18 @@ static int max14577_suspend(struct device *dev) struct i2c_client *i2c = container_of(dev, struct i2c_client, dev); struct max14577 *max14577 = i2c_get_clientdata(i2c); - if (device_may_wakeup(dev)) { + if (device_may_wakeup(dev)) enable_irq_wake(max14577->irq); - /* - * MUIC IRQ must be disabled during suspend if this is - * a wake up source because it will be handled before - * resuming I2C. - * - * When device is woken up from suspend (e.g. by ADC change), - * an interrupt occurs before resuming I2C bus controller. - * Interrupt handler tries to read registers but this read - * will fail because I2C is still suspended. - */ - disable_irq(max14577->irq); - } + /* + * MUIC IRQ must be disabled during suspend because if it happens + * while suspended it will be handled before resuming I2C. + * + * When device is woken up from suspend (e.g. by ADC change), + * an interrupt occurs before resuming I2C bus controller. + * Interrupt handler tries to read registers but this read + * will fail because I2C is still suspended. + */ + disable_irq(max14577->irq); return 0; } @@ -206,20 +436,14 @@ static int max14577_resume(struct device *dev) struct i2c_client *i2c = container_of(dev, struct i2c_client, dev); struct max14577 *max14577 = i2c_get_clientdata(i2c); - if (device_may_wakeup(dev)) { + if (device_may_wakeup(dev)) disable_irq_wake(max14577->irq); - enable_irq(max14577->irq); - } + enable_irq(max14577->irq); return 0; } #endif /* CONFIG_PM_SLEEP */ -static struct of_device_id max14577_dt_match[] = { - { .compatible = "maxim,max14577", }, - {}, -}; - static SIMPLE_DEV_PM_OPS(max14577_pm, max14577_suspend, max14577_resume); static struct i2c_driver max14577_i2c_driver = { @@ -236,6 +460,9 @@ static struct i2c_driver max14577_i2c_driver = { static int __init max14577_i2c_init(void) { + BUILD_BUG_ON(ARRAY_SIZE(max14577_i2c_id) != MAXIM_DEVICE_TYPE_NUM); + BUILD_BUG_ON(ARRAY_SIZE(max14577_dt_match) != MAXIM_DEVICE_TYPE_NUM); + return i2c_add_driver(&max14577_i2c_driver); } subsys_initcall(max14577_i2c_init); @@ -247,5 +474,5 @@ static void __exit max14577_i2c_exit(void) module_exit(max14577_i2c_exit); MODULE_AUTHOR("Chanwoo Choi <cw00.choi@samsung.com>, Krzysztof Kozlowski <k.kozlowski@samsung.com>"); -MODULE_DESCRIPTION("MAXIM 14577 multi-function core driver"); +MODULE_DESCRIPTION("Maxim 14577/77836 multi-function core driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/mfd/max77686.c b/drivers/mfd/max77686.c index e5fce765accb..ce869acf27ae 100644 --- a/drivers/mfd/max77686.c +++ b/drivers/mfd/max77686.c @@ -47,7 +47,7 @@ static struct regmap_config max77686_regmap_config = { }; #ifdef CONFIG_OF -static struct of_device_id max77686_pmic_dt_match[] = { +static const struct of_device_id max77686_pmic_dt_match[] = { {.compatible = "maxim,max77686", .data = NULL}, {}, }; diff --git a/drivers/mfd/max77693.c b/drivers/mfd/max77693.c index c5535f018466..7e05428c756d 100644 --- a/drivers/mfd/max77693.c +++ b/drivers/mfd/max77693.c @@ -243,7 +243,7 @@ static const struct dev_pm_ops max77693_pm = { }; #ifdef CONFIG_OF -static struct of_device_id max77693_dt_match[] = { +static const struct of_device_id max77693_dt_match[] = { { .compatible = "maxim,max77693" }, {}, }; diff --git a/drivers/mfd/max8907.c b/drivers/mfd/max8907.c index 07740314b29d..232749c8813d 100644 --- a/drivers/mfd/max8907.c +++ b/drivers/mfd/max8907.c @@ -305,7 +305,7 @@ static int max8907_i2c_remove(struct i2c_client *i2c) } #ifdef CONFIG_OF -static struct of_device_id max8907_of_match[] = { +static const struct of_device_id max8907_of_match[] = { { .compatible = "maxim,max8907" }, { }, }; diff --git a/drivers/mfd/max8997.c b/drivers/mfd/max8997.c index 8cf7a015cfe5..595364ee178a 100644 --- a/drivers/mfd/max8997.c +++ b/drivers/mfd/max8997.c @@ -51,7 +51,7 @@ static const struct mfd_cell max8997_devs[] = { }; #ifdef CONFIG_OF -static struct of_device_id max8997_pmic_dt_match[] = { +static const struct of_device_id max8997_pmic_dt_match[] = { { .compatible = "maxim,max8997-pmic", .data = (void *)TYPE_MAX8997 }, {}, }; diff --git a/drivers/mfd/max8998.c b/drivers/mfd/max8998.c index 592db06098e6..a37cb7444b6e 100644 --- a/drivers/mfd/max8998.c +++ b/drivers/mfd/max8998.c @@ -132,7 +132,7 @@ int max8998_update_reg(struct i2c_client *i2c, u8 reg, u8 val, u8 mask) EXPORT_SYMBOL(max8998_update_reg); #ifdef CONFIG_OF -static struct of_device_id max8998_dt_match[] = { +static const struct of_device_id max8998_dt_match[] = { { .compatible = "maxim,max8998", .data = (void *)TYPE_MAX8998 }, { .compatible = "national,lp3974", .data = (void *)TYPE_LP3974 }, { .compatible = "ti,lp3974", .data = (void *)TYPE_LP3974 }, diff --git a/drivers/mfd/mc13xxx-core.c b/drivers/mfd/mc13xxx-core.c index 06e64b6fcb89..acf5dd712eb2 100644 --- a/drivers/mfd/mc13xxx-core.c +++ b/drivers/mfd/mc13xxx-core.c @@ -660,30 +660,22 @@ int mc13xxx_common_init(struct device *dev) if (ret) return ret; + mutex_init(&mc13xxx->lock); + ret = request_threaded_irq(mc13xxx->irq, NULL, mc13xxx_irq_thread, IRQF_ONESHOT | IRQF_TRIGGER_HIGH, "mc13xxx", mc13xxx); if (ret) return ret; - mutex_init(&mc13xxx->lock); - if (mc13xxx_probe_flags_dt(mc13xxx) < 0 && pdata) mc13xxx->flags = pdata->flags; if (mc13xxx->flags & MC13XXX_USE_ADC) mc13xxx_add_subdevice(mc13xxx, "%s-adc"); - if (mc13xxx->flags & MC13XXX_USE_CODEC) - mc13xxx_add_subdevice_pdata(mc13xxx, "%s-codec", - pdata->codec, sizeof(*pdata->codec)); - if (mc13xxx->flags & MC13XXX_USE_RTC) mc13xxx_add_subdevice(mc13xxx, "%s-rtc"); - if (mc13xxx->flags & MC13XXX_USE_TOUCHSCREEN) - mc13xxx_add_subdevice_pdata(mc13xxx, "%s-ts", - &pdata->touch, sizeof(pdata->touch)); - if (pdata) { mc13xxx_add_subdevice_pdata(mc13xxx, "%s-regulator", &pdata->regulators, sizeof(pdata->regulators)); @@ -691,10 +683,20 @@ int mc13xxx_common_init(struct device *dev) pdata->leds, sizeof(*pdata->leds)); mc13xxx_add_subdevice_pdata(mc13xxx, "%s-pwrbutton", pdata->buttons, sizeof(*pdata->buttons)); + if (mc13xxx->flags & MC13XXX_USE_CODEC) + mc13xxx_add_subdevice_pdata(mc13xxx, "%s-codec", + pdata->codec, sizeof(*pdata->codec)); + if (mc13xxx->flags & MC13XXX_USE_TOUCHSCREEN) + mc13xxx_add_subdevice_pdata(mc13xxx, "%s-ts", + &pdata->touch, sizeof(pdata->touch)); } else { mc13xxx_add_subdevice(mc13xxx, "%s-regulator"); mc13xxx_add_subdevice(mc13xxx, "%s-led"); mc13xxx_add_subdevice(mc13xxx, "%s-pwrbutton"); + if (mc13xxx->flags & MC13XXX_USE_CODEC) + mc13xxx_add_subdevice(mc13xxx, "%s-codec"); + if (mc13xxx->flags & MC13XXX_USE_TOUCHSCREEN) + mc13xxx_add_subdevice(mc13xxx, "%s-ts"); } return 0; diff --git a/drivers/mfd/menelaus.c b/drivers/mfd/menelaus.c index ad25bfa3fb02..5e2667afe2bc 100644 --- a/drivers/mfd/menelaus.c +++ b/drivers/mfd/menelaus.c @@ -1287,29 +1287,8 @@ static struct i2c_driver menelaus_i2c_driver = { .id_table = menelaus_id, }; -static int __init menelaus_init(void) -{ - int res; - - res = i2c_add_driver(&menelaus_i2c_driver); - if (res < 0) { - pr_err(DRIVER_NAME ": driver registration failed\n"); - return res; - } - - return 0; -} - -static void __exit menelaus_exit(void) -{ - i2c_del_driver(&menelaus_i2c_driver); - - /* FIXME: Shutdown menelaus parts that can be shut down */ -} +module_i2c_driver(menelaus_i2c_driver); MODULE_AUTHOR("Texas Instruments, Inc. (and others)"); MODULE_DESCRIPTION("I2C interface for Menelaus."); MODULE_LICENSE("GPL"); - -module_init(menelaus_init); -module_exit(menelaus_exit); diff --git a/drivers/mfd/mfd-core.c b/drivers/mfd/mfd-core.c index 267649244737..892d343193ad 100644 --- a/drivers/mfd/mfd-core.c +++ b/drivers/mfd/mfd-core.c @@ -102,7 +102,7 @@ static int mfd_add_device(struct device *parent, int id, pdev->dev.dma_mask = parent->dma_mask; pdev->dev.dma_parms = parent->dma_parms; - ret = devm_regulator_bulk_register_supply_alias( + ret = regulator_bulk_register_supply_alias( &pdev->dev, cell->parent_supplies, parent, cell->parent_supplies, cell->num_parent_supplies); @@ -182,9 +182,9 @@ static int mfd_add_device(struct device *parent, int id, return 0; fail_alias: - devm_regulator_bulk_unregister_supply_alias(&pdev->dev, - cell->parent_supplies, - cell->num_parent_supplies); + regulator_bulk_unregister_supply_alias(&pdev->dev, + cell->parent_supplies, + cell->num_parent_supplies); fail_res: kfree(res); fail_device: @@ -238,6 +238,9 @@ static int mfd_remove_devices_fn(struct device *dev, void *c) pdev = to_platform_device(dev); cell = mfd_get_cell(pdev); + regulator_bulk_unregister_supply_alias(dev, cell->parent_supplies, + cell->num_parent_supplies); + /* find the base address of usage_count pointers (for freeing) */ if (!*usage_count || (cell->usage_count < *usage_count)) *usage_count = cell->usage_count; diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c index 651e249287dc..b48d80c367f9 100644 --- a/drivers/mfd/omap-usb-host.c +++ b/drivers/mfd/omap-usb-host.c @@ -557,7 +557,7 @@ static int usbhs_omap_get_dt_pdata(struct device *dev, return 0; } -static struct of_device_id usbhs_child_match_table[] = { +static const struct of_device_id usbhs_child_match_table[] = { { .compatible = "ti,omap-ehci", }, { .compatible = "ti,omap-ohci", }, { } diff --git a/drivers/mfd/palmas.c b/drivers/mfd/palmas.c index d280d789e55a..28cb048f4760 100644 --- a/drivers/mfd/palmas.c +++ b/drivers/mfd/palmas.c @@ -25,52 +25,6 @@ #include <linux/mfd/palmas.h> #include <linux/of_device.h> -#define PALMAS_EXT_REQ (PALMAS_EXT_CONTROL_ENABLE1 | \ - PALMAS_EXT_CONTROL_ENABLE2 | \ - PALMAS_EXT_CONTROL_NSLEEP) - -struct palmas_sleep_requestor_info { - int id; - int reg_offset; - int bit_pos; -}; - -#define EXTERNAL_REQUESTOR(_id, _offset, _pos) \ - [PALMAS_EXTERNAL_REQSTR_ID_##_id] = { \ - .id = PALMAS_EXTERNAL_REQSTR_ID_##_id, \ - .reg_offset = _offset, \ - .bit_pos = _pos, \ - } - -static struct palmas_sleep_requestor_info sleep_req_info[] = { - EXTERNAL_REQUESTOR(REGEN1, 0, 0), - EXTERNAL_REQUESTOR(REGEN2, 0, 1), - EXTERNAL_REQUESTOR(SYSEN1, 0, 2), - EXTERNAL_REQUESTOR(SYSEN2, 0, 3), - EXTERNAL_REQUESTOR(CLK32KG, 0, 4), - EXTERNAL_REQUESTOR(CLK32KGAUDIO, 0, 5), - EXTERNAL_REQUESTOR(REGEN3, 0, 6), - EXTERNAL_REQUESTOR(SMPS12, 1, 0), - EXTERNAL_REQUESTOR(SMPS3, 1, 1), - EXTERNAL_REQUESTOR(SMPS45, 1, 2), - EXTERNAL_REQUESTOR(SMPS6, 1, 3), - EXTERNAL_REQUESTOR(SMPS7, 1, 4), - EXTERNAL_REQUESTOR(SMPS8, 1, 5), - EXTERNAL_REQUESTOR(SMPS9, 1, 6), - EXTERNAL_REQUESTOR(SMPS10, 1, 7), - EXTERNAL_REQUESTOR(LDO1, 2, 0), - EXTERNAL_REQUESTOR(LDO2, 2, 1), - EXTERNAL_REQUESTOR(LDO3, 2, 2), - EXTERNAL_REQUESTOR(LDO4, 2, 3), - EXTERNAL_REQUESTOR(LDO5, 2, 4), - EXTERNAL_REQUESTOR(LDO6, 2, 5), - EXTERNAL_REQUESTOR(LDO7, 2, 6), - EXTERNAL_REQUESTOR(LDO8, 2, 7), - EXTERNAL_REQUESTOR(LDO9, 3, 0), - EXTERNAL_REQUESTOR(LDOLN, 3, 1), - EXTERNAL_REQUESTOR(LDOUSB, 3, 2), -}; - static const struct regmap_config palmas_regmap_config[PALMAS_NUM_CLIENTS] = { { .reg_bits = 8, @@ -92,6 +46,133 @@ static const struct regmap_config palmas_regmap_config[PALMAS_NUM_CLIENTS] = { }, }; +static const struct regmap_irq tps65917_irqs[] = { + /* INT1 IRQs */ + [TPS65917_RESERVED1] = { + .mask = TPS65917_RESERVED, + }, + [TPS65917_PWRON_IRQ] = { + .mask = TPS65917_INT1_STATUS_PWRON, + }, + [TPS65917_LONG_PRESS_KEY_IRQ] = { + .mask = TPS65917_INT1_STATUS_LONG_PRESS_KEY, + }, + [TPS65917_RESERVED2] = { + .mask = TPS65917_RESERVED, + }, + [TPS65917_PWRDOWN_IRQ] = { + .mask = TPS65917_INT1_STATUS_PWRDOWN, + }, + [TPS65917_HOTDIE_IRQ] = { + .mask = TPS65917_INT1_STATUS_HOTDIE, + }, + [TPS65917_VSYS_MON_IRQ] = { + .mask = TPS65917_INT1_STATUS_VSYS_MON, + }, + [TPS65917_RESERVED3] = { + .mask = TPS65917_RESERVED, + }, + /* INT2 IRQs*/ + [TPS65917_RESERVED4] = { + .mask = TPS65917_RESERVED, + .reg_offset = 1, + }, + [TPS65917_OTP_ERROR_IRQ] = { + .mask = TPS65917_INT2_STATUS_OTP_ERROR, + .reg_offset = 1, + }, + [TPS65917_WDT_IRQ] = { + .mask = TPS65917_INT2_STATUS_WDT, + .reg_offset = 1, + }, + [TPS65917_RESERVED5] = { + .mask = TPS65917_RESERVED, + .reg_offset = 1, + }, + [TPS65917_RESET_IN_IRQ] = { + .mask = TPS65917_INT2_STATUS_RESET_IN, + .reg_offset = 1, + }, + [TPS65917_FSD_IRQ] = { + .mask = TPS65917_INT2_STATUS_FSD, + .reg_offset = 1, + }, + [TPS65917_SHORT_IRQ] = { + .mask = TPS65917_INT2_STATUS_SHORT, + .reg_offset = 1, + }, + [TPS65917_RESERVED6] = { + .mask = TPS65917_RESERVED, + .reg_offset = 1, + }, + /* INT3 IRQs */ + [TPS65917_GPADC_AUTO_0_IRQ] = { + .mask = TPS65917_INT3_STATUS_GPADC_AUTO_0, + .reg_offset = 2, + }, + [TPS65917_GPADC_AUTO_1_IRQ] = { + .mask = TPS65917_INT3_STATUS_GPADC_AUTO_1, + .reg_offset = 2, + }, + [TPS65917_GPADC_EOC_SW_IRQ] = { + .mask = TPS65917_INT3_STATUS_GPADC_EOC_SW, + .reg_offset = 2, + }, + [TPS65917_RESREVED6] = { + .mask = TPS65917_RESERVED6, + .reg_offset = 2, + }, + [TPS65917_RESERVED7] = { + .mask = TPS65917_RESERVED, + .reg_offset = 2, + }, + [TPS65917_RESERVED8] = { + .mask = TPS65917_RESERVED, + .reg_offset = 2, + }, + [TPS65917_RESERVED9] = { + .mask = TPS65917_RESERVED, + .reg_offset = 2, + }, + [TPS65917_VBUS_IRQ] = { + .mask = TPS65917_INT3_STATUS_VBUS, + .reg_offset = 2, + }, + /* INT4 IRQs */ + [TPS65917_GPIO_0_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_0, + .reg_offset = 3, + }, + [TPS65917_GPIO_1_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_1, + .reg_offset = 3, + }, + [TPS65917_GPIO_2_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_2, + .reg_offset = 3, + }, + [TPS65917_GPIO_3_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_3, + .reg_offset = 3, + }, + [TPS65917_GPIO_4_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_4, + .reg_offset = 3, + }, + [TPS65917_GPIO_5_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_5, + .reg_offset = 3, + }, + [TPS65917_GPIO_6_IRQ] = { + .mask = TPS65917_INT4_STATUS_GPIO_6, + .reg_offset = 3, + }, + [TPS65917_RESERVED10] = { + .mask = TPS65917_RESERVED10, + .reg_offset = 3, + }, +}; + static const struct regmap_irq palmas_irqs[] = { /* INT1 IRQs */ [PALMAS_CHARG_DET_N_VBUS_OVV_IRQ] = { @@ -232,13 +313,26 @@ static struct regmap_irq_chip palmas_irq_chip = { PALMAS_INT1_MASK), }; +static struct regmap_irq_chip tps65917_irq_chip = { + .name = "tps65917", + .irqs = tps65917_irqs, + .num_irqs = ARRAY_SIZE(tps65917_irqs), + + .num_regs = 4, + .irq_reg_stride = 5, + .status_base = PALMAS_BASE_TO_REG(PALMAS_INTERRUPT_BASE, + PALMAS_INT1_STATUS), + .mask_base = PALMAS_BASE_TO_REG(PALMAS_INTERRUPT_BASE, + PALMAS_INT1_MASK), +}; + int palmas_ext_control_req_config(struct palmas *palmas, enum palmas_external_requestor_id id, int ext_ctrl, bool enable) { + struct palmas_pmic_driver_data *pmic_ddata = palmas->pmic_ddata; int preq_mask_bit = 0; int reg_add = 0; - int bit_pos; - int ret; + int bit_pos, ret; if (!(ext_ctrl & PALMAS_EXT_REQ)) return 0; @@ -257,8 +351,8 @@ int palmas_ext_control_req_config(struct palmas *palmas, preq_mask_bit = 2; } - bit_pos = sleep_req_info[id].bit_pos; - reg_add += sleep_req_info[id].reg_offset; + bit_pos = pmic_ddata->sleep_req_info[id].bit_pos; + reg_add += pmic_ddata->sleep_req_info[id].reg_offset; if (enable) ret = palmas_update_bits(palmas, PALMAS_RESOURCE_BASE, reg_add, BIT(bit_pos), BIT(bit_pos)); @@ -357,14 +451,38 @@ static void palmas_power_off(void) static unsigned int palmas_features = PALMAS_PMIC_FEATURE_SMPS10_BOOST; static unsigned int tps659038_features; +struct palmas_driver_data { + unsigned int *features; + struct regmap_irq_chip *irq_chip; +}; + +static struct palmas_driver_data palmas_data = { + .features = &palmas_features, + .irq_chip = &palmas_irq_chip, +}; + +static struct palmas_driver_data tps659038_data = { + .features = &tps659038_features, + .irq_chip = &palmas_irq_chip, +}; + +static struct palmas_driver_data tps65917_data = { + .features = &tps659038_features, + .irq_chip = &tps65917_irq_chip, +}; + static const struct of_device_id of_palmas_match_tbl[] = { { .compatible = "ti,palmas", - .data = &palmas_features, + .data = &palmas_data, }, { .compatible = "ti,tps659038", - .data = &tps659038_features, + .data = &tps659038_data, + }, + { + .compatible = "ti,tps65917", + .data = &tps65917_data, }, { }, }; @@ -375,9 +493,10 @@ static int palmas_i2c_probe(struct i2c_client *i2c, { struct palmas *palmas; struct palmas_platform_data *pdata; + struct palmas_driver_data *driver_data; struct device_node *node = i2c->dev.of_node; int ret = 0, i; - unsigned int reg, addr, *features; + unsigned int reg, addr; int slave; const struct of_device_id *match; @@ -408,8 +527,8 @@ static int palmas_i2c_probe(struct i2c_client *i2c, if (!match) return -ENODATA; - features = (unsigned int *)match->data; - palmas->features = *features; + driver_data = (struct palmas_driver_data *)match->data; + palmas->features = *driver_data->features; for (i = 0; i < PALMAS_NUM_CLIENTS; i++) { if (i == 0) @@ -463,8 +582,8 @@ static int palmas_i2c_probe(struct i2c_client *i2c, regmap_write(palmas->regmap[slave], addr, reg); ret = regmap_add_irq_chip(palmas->regmap[slave], palmas->irq, - IRQF_ONESHOT | pdata->irq_flags, 0, &palmas_irq_chip, - &palmas->irq_data); + IRQF_ONESHOT | pdata->irq_flags, 0, + driver_data->irq_chip, &palmas->irq_data); if (ret < 0) goto err_i2c; diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c index b97a97187ae9..959513803542 100644 --- a/drivers/mfd/pm8921-core.c +++ b/drivers/mfd/pm8921-core.c @@ -26,7 +26,6 @@ #include <linux/regmap.h> #include <linux/of_platform.h> #include <linux/mfd/core.h> -#include <linux/mfd/pm8xxx/core.h> #define SSBI_REG_ADDR_IRQ_BASE 0x1BB @@ -57,7 +56,6 @@ #define PM8921_NR_IRQS 256 struct pm_irq_chip { - struct device *dev; struct regmap *regmap; spinlock_t pm_irq_lock; struct irq_domain *irqdomain; @@ -67,11 +65,6 @@ struct pm_irq_chip { u8 config[0]; }; -struct pm8921 { - struct device *dev; - struct pm_irq_chip *irq_chip; -}; - static int pm8xxx_read_block_irq(struct pm_irq_chip *chip, unsigned int bp, unsigned int *ip) { @@ -255,55 +248,6 @@ static struct irq_chip pm8xxx_irq_chip = { .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE, }; -/** - * pm8xxx_get_irq_stat - get the status of the irq line - * @chip: pointer to identify a pmic irq controller - * @irq: the irq number - * - * The pm8xxx gpio and mpp rely on the interrupt block to read - * the values on their pins. This function is to facilitate reading - * the status of a gpio or an mpp line. The caller has to convert the - * gpio number to irq number. - * - * RETURNS: - * an int indicating the value read on that line - */ -static int pm8xxx_get_irq_stat(struct pm_irq_chip *chip, int irq) -{ - int pmirq, rc; - unsigned int block, bits, bit; - unsigned long flags; - struct irq_data *irq_data = irq_get_irq_data(irq); - - pmirq = irq_data->hwirq; - - block = pmirq / 8; - bit = pmirq % 8; - - spin_lock_irqsave(&chip->pm_irq_lock, flags); - - rc = regmap_write(chip->regmap, SSBI_REG_ADDR_IRQ_BLK_SEL, block); - if (rc) { - pr_err("Failed Selecting block irq=%d pmirq=%d blk=%d rc=%d\n", - irq, pmirq, block, rc); - goto bail_out; - } - - rc = regmap_read(chip->regmap, SSBI_REG_ADDR_IRQ_RT_STATUS, &bits); - if (rc) { - pr_err("Failed Configuring irq=%d pmirq=%d blk=%d rc=%d\n", - irq, pmirq, block, rc); - goto bail_out; - } - - rc = (bits & (1 << bit)) ? 1 : 0; - -bail_out: - spin_unlock_irqrestore(&chip->pm_irq_lock, flags); - - return rc; -} - static int pm8xxx_irq_domain_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hwirq) { @@ -324,56 +268,6 @@ static const struct irq_domain_ops pm8xxx_irq_domain_ops = { .map = pm8xxx_irq_domain_map, }; -static int pm8921_readb(const struct device *dev, u16 addr, u8 *val) -{ - const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev); - const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data; - - return ssbi_read(pmic->dev->parent, addr, val, 1); -} - -static int pm8921_writeb(const struct device *dev, u16 addr, u8 val) -{ - const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev); - const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data; - - return ssbi_write(pmic->dev->parent, addr, &val, 1); -} - -static int pm8921_read_buf(const struct device *dev, u16 addr, u8 *buf, - int cnt) -{ - const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev); - const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data; - - return ssbi_read(pmic->dev->parent, addr, buf, cnt); -} - -static int pm8921_write_buf(const struct device *dev, u16 addr, u8 *buf, - int cnt) -{ - const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev); - const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data; - - return ssbi_write(pmic->dev->parent, addr, buf, cnt); -} - -static int pm8921_read_irq_stat(const struct device *dev, int irq) -{ - const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev); - const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data; - - return pm8xxx_get_irq_stat(pmic->irq_chip, irq); -} - -static struct pm8xxx_drvdata pm8921_drvdata = { - .pmic_readb = pm8921_readb, - .pmic_writeb = pm8921_writeb, - .pmic_read_buf = pm8921_read_buf, - .pmic_write_buf = pm8921_write_buf, - .pmic_read_irq_stat = pm8921_read_irq_stat, -}; - static const struct regmap_config ssbi_regmap_config = { .reg_bits = 16, .val_bits = 8, @@ -392,7 +286,6 @@ MODULE_DEVICE_TABLE(of, pm8921_id_table); static int pm8921_probe(struct platform_device *pdev) { - struct pm8921 *pmic; struct regmap *regmap; int irq, rc; unsigned int val; @@ -404,12 +297,6 @@ static int pm8921_probe(struct platform_device *pdev) if (irq < 0) return irq; - pmic = devm_kzalloc(&pdev->dev, sizeof(struct pm8921), GFP_KERNEL); - if (!pmic) { - pr_err("Cannot alloc pm8921 struct\n"); - return -ENOMEM; - } - regmap = devm_regmap_init(&pdev->dev, NULL, pdev->dev.parent, &ssbi_regmap_config); if (IS_ERR(regmap)) @@ -434,18 +321,13 @@ static int pm8921_probe(struct platform_device *pdev) pr_info("PMIC revision 2: %02X\n", val); rev |= val << BITS_PER_BYTE; - pmic->dev = &pdev->dev; - pm8921_drvdata.pm_chip_data = pmic; - platform_set_drvdata(pdev, &pm8921_drvdata); - chip = devm_kzalloc(&pdev->dev, sizeof(*chip) + sizeof(chip->config[0]) * nirqs, GFP_KERNEL); if (!chip) return -ENOMEM; - pmic->irq_chip = chip; - chip->dev = &pdev->dev; + platform_set_drvdata(pdev, chip); chip->regmap = regmap; chip->num_irqs = nirqs; chip->num_blocks = DIV_ROUND_UP(chip->num_irqs, 8); @@ -481,8 +363,7 @@ static int pm8921_remove_child(struct device *dev, void *unused) static int pm8921_remove(struct platform_device *pdev) { int irq = platform_get_irq(pdev, 0); - struct pm8921 *pmic = pm8921_drvdata.pm_chip_data; - struct pm_irq_chip *chip = pmic->irq_chip; + struct pm_irq_chip *chip = platform_get_drvdata(pdev); device_for_each_child(&pdev->dev, NULL, pm8921_remove_child); irq_set_chained_handler(irq, NULL); diff --git a/drivers/mfd/rdc321x-southbridge.c b/drivers/mfd/rdc321x-southbridge.c index c79569750be9..6575585f1d1f 100644 --- a/drivers/mfd/rdc321x-southbridge.c +++ b/drivers/mfd/rdc321x-southbridge.c @@ -38,7 +38,7 @@ static struct resource rdc321x_wdt_resource[] = { }; static struct rdc321x_gpio_pdata rdc321x_gpio_pdata = { - .max_gpios = RDC321X_MAX_GPIO, + .max_gpios = RDC321X_NUM_GPIO, }; static struct resource rdc321x_gpio_resources[] = { diff --git a/drivers/mfd/rtsx_usb.c b/drivers/mfd/rtsx_usb.c index b53b9d46cc45..6352bec8419a 100644 --- a/drivers/mfd/rtsx_usb.c +++ b/drivers/mfd/rtsx_usb.c @@ -29,7 +29,7 @@ static int polling_pipe = 1; module_param(polling_pipe, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(polling_pipe, "polling pipe (0: ctl, 1: bulk)"); -static struct mfd_cell rtsx_usb_cells[] = { +static const struct mfd_cell rtsx_usb_cells[] = { [RTSX_USB_SD_CARD] = { .name = "rtsx_usb_sdmmc", .pdata_size = 0, @@ -67,7 +67,7 @@ static int rtsx_usb_bulk_transfer_sglist(struct rtsx_ucr *ucr, ucr->sg_timer.expires = jiffies + msecs_to_jiffies(timeout); add_timer(&ucr->sg_timer); usb_sg_wait(&ucr->current_sg); - del_timer(&ucr->sg_timer); + del_timer_sync(&ucr->sg_timer); if (act_len) *act_len = ucr->current_sg.bytes; @@ -644,14 +644,14 @@ static int rtsx_usb_probe(struct usb_interface *intf, if (ret) goto out_init_fail; + /* initialize USB SG transfer timer */ + setup_timer(&ucr->sg_timer, rtsx_usb_sg_timed_out, (unsigned long) ucr); + ret = mfd_add_devices(&intf->dev, usb_dev->devnum, rtsx_usb_cells, ARRAY_SIZE(rtsx_usb_cells), NULL, 0, NULL); if (ret) goto out_init_fail; - /* initialize USB SG transfer timer */ - init_timer(&ucr->sg_timer); - setup_timer(&ucr->sg_timer, rtsx_usb_sg_timed_out, (unsigned long) ucr); #ifdef CONFIG_PM intf->needs_remote_wakeup = 1; usb_enable_autosuspend(usb_dev); @@ -687,9 +687,15 @@ static int rtsx_usb_suspend(struct usb_interface *intf, pm_message_t message) dev_dbg(&intf->dev, "%s called with pm message 0x%04u\n", __func__, message.event); + /* + * Call to make sure LED is off during suspend to save more power. + * It is NOT a permanent state and could be turned on anytime later. + * Thus no need to call turn_on when resunming. + */ mutex_lock(&ucr->dev_mutex); rtsx_usb_turn_off_led(ucr); mutex_unlock(&ucr->dev_mutex); + return 0; } diff --git a/drivers/mfd/sec-core.c b/drivers/mfd/sec-core.c index 1cf27521fff4..be06d0abbf19 100644 --- a/drivers/mfd/sec-core.c +++ b/drivers/mfd/sec-core.c @@ -25,7 +25,6 @@ #include <linux/mfd/core.h> #include <linux/mfd/samsung/core.h> #include <linux/mfd/samsung/irq.h> -#include <linux/mfd/samsung/rtc.h> #include <linux/mfd/samsung/s2mpa01.h> #include <linux/mfd/samsung/s2mps11.h> #include <linux/mfd/samsung/s2mps14.h> @@ -91,7 +90,7 @@ static const struct mfd_cell s2mpa01_devs[] = { }; #ifdef CONFIG_OF -static struct of_device_id sec_dt_match[] = { +static const struct of_device_id sec_dt_match[] = { { .compatible = "samsung,s5m8767-pmic", .data = (void *)S5M8767X, }, { @@ -196,20 +195,6 @@ static const struct regmap_config s5m8767_regmap_config = { .cache_type = REGCACHE_FLAT, }; -static const struct regmap_config s5m_rtc_regmap_config = { - .reg_bits = 8, - .val_bits = 8, - - .max_register = SEC_RTC_REG_MAX, -}; - -static const struct regmap_config s2mps14_rtc_regmap_config = { - .reg_bits = 8, - .val_bits = 8, - - .max_register = S2MPS_RTC_REG_MAX, -}; - #ifdef CONFIG_OF /* * Only the common platform data elements for s5m8767 are parsed here from the @@ -264,8 +249,9 @@ static int sec_pmic_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { struct sec_platform_data *pdata = dev_get_platdata(&i2c->dev); - const struct regmap_config *regmap, *regmap_rtc; + const struct regmap_config *regmap; struct sec_pmic_dev *sec_pmic; + unsigned long device_type; int ret; sec_pmic = devm_kzalloc(&i2c->dev, sizeof(struct sec_pmic_dev), @@ -277,7 +263,7 @@ static int sec_pmic_probe(struct i2c_client *i2c, sec_pmic->dev = &i2c->dev; sec_pmic->i2c = i2c; sec_pmic->irq = i2c->irq; - sec_pmic->type = sec_i2c_get_driver_data(i2c, id); + device_type = sec_i2c_get_driver_data(i2c, id); if (sec_pmic->dev->of_node) { pdata = sec_pmic_i2c_parse_dt_pdata(sec_pmic->dev); @@ -285,7 +271,7 @@ static int sec_pmic_probe(struct i2c_client *i2c, ret = PTR_ERR(pdata); return ret; } - pdata->device_type = sec_pmic->type; + pdata->device_type = device_type; } if (pdata) { sec_pmic->device_type = pdata->device_type; @@ -298,39 +284,21 @@ static int sec_pmic_probe(struct i2c_client *i2c, switch (sec_pmic->device_type) { case S2MPA01: regmap = &s2mpa01_regmap_config; - /* - * The rtc-s5m driver does not support S2MPA01 and there - * is no mfd_cell for S2MPA01 RTC device. - * However we must pass something to devm_regmap_init_i2c() - * so use S5M-like regmap config even though it wouldn't work. - */ - regmap_rtc = &s5m_rtc_regmap_config; break; case S2MPS11X: regmap = &s2mps11_regmap_config; - /* - * The rtc-s5m driver does not support S2MPS11 and there - * is no mfd_cell for S2MPS11 RTC device. - * However we must pass something to devm_regmap_init_i2c() - * so use S5M-like regmap config even though it wouldn't work. - */ - regmap_rtc = &s5m_rtc_regmap_config; break; case S2MPS14X: regmap = &s2mps14_regmap_config; - regmap_rtc = &s2mps14_rtc_regmap_config; break; case S5M8763X: regmap = &s5m8763_regmap_config; - regmap_rtc = &s5m_rtc_regmap_config; break; case S5M8767X: regmap = &s5m8767_regmap_config; - regmap_rtc = &s5m_rtc_regmap_config; break; default: regmap = &sec_regmap_config; - regmap_rtc = &s5m_rtc_regmap_config; break; } @@ -342,21 +310,6 @@ static int sec_pmic_probe(struct i2c_client *i2c, return ret; } - sec_pmic->rtc = i2c_new_dummy(i2c->adapter, RTC_I2C_ADDR); - if (!sec_pmic->rtc) { - dev_err(&i2c->dev, "Failed to allocate I2C for RTC\n"); - return -ENODEV; - } - i2c_set_clientdata(sec_pmic->rtc, sec_pmic); - - sec_pmic->regmap_rtc = devm_regmap_init_i2c(sec_pmic->rtc, regmap_rtc); - if (IS_ERR(sec_pmic->regmap_rtc)) { - ret = PTR_ERR(sec_pmic->regmap_rtc); - dev_err(&i2c->dev, "Failed to allocate RTC register map: %d\n", - ret); - goto err_regmap_rtc; - } - if (pdata && pdata->cfg_pmic_irq) pdata->cfg_pmic_irq(); @@ -403,8 +356,6 @@ static int sec_pmic_probe(struct i2c_client *i2c, err_mfd: sec_irq_exit(sec_pmic); -err_regmap_rtc: - i2c_unregister_device(sec_pmic->rtc); return ret; } @@ -414,7 +365,6 @@ static int sec_pmic_remove(struct i2c_client *i2c) mfd_remove_devices(sec_pmic->dev); sec_irq_exit(sec_pmic); - i2c_unregister_device(sec_pmic->rtc); return 0; } @@ -424,19 +374,18 @@ static int sec_pmic_suspend(struct device *dev) struct i2c_client *i2c = container_of(dev, struct i2c_client, dev); struct sec_pmic_dev *sec_pmic = i2c_get_clientdata(i2c); - if (device_may_wakeup(dev)) { + if (device_may_wakeup(dev)) enable_irq_wake(sec_pmic->irq); - /* - * PMIC IRQ must be disabled during suspend for RTC alarm - * to work properly. - * When device is woken up from suspend by RTC Alarm, an - * interrupt occurs before resuming I2C bus controller. - * The interrupt is handled by regmap_irq_thread which tries - * to read RTC registers. This read fails (I2C is still - * suspended) and RTC Alarm interrupt is disabled. - */ - disable_irq(sec_pmic->irq); - } + /* + * PMIC IRQ must be disabled during suspend for RTC alarm + * to work properly. + * When device is woken up from suspend, an + * interrupt occurs before resuming I2C bus controller. + * The interrupt is handled by regmap_irq_thread which tries + * to read RTC registers. This read fails (I2C is still + * suspended) and RTC Alarm interrupt is disabled. + */ + disable_irq(sec_pmic->irq); return 0; } @@ -446,10 +395,9 @@ static int sec_pmic_resume(struct device *dev) struct i2c_client *i2c = container_of(dev, struct i2c_client, dev); struct sec_pmic_dev *sec_pmic = i2c_get_clientdata(i2c); - if (device_may_wakeup(dev)) { + if (device_may_wakeup(dev)) disable_irq_wake(sec_pmic->irq); - enable_irq(sec_pmic->irq); - } + enable_irq(sec_pmic->irq); return 0; } diff --git a/drivers/mfd/sec-irq.c b/drivers/mfd/sec-irq.c index 64e7913aadc6..654e2c1dbf7a 100644 --- a/drivers/mfd/sec-irq.c +++ b/drivers/mfd/sec-irq.c @@ -385,7 +385,7 @@ int sec_irq_init(struct sec_pmic_dev *sec_pmic) &sec_pmic->irq_data); break; default: - dev_err(sec_pmic->dev, "Unknown device type %d\n", + dev_err(sec_pmic->dev, "Unknown device type %lu\n", sec_pmic->device_type); return -EINVAL; } diff --git a/drivers/mfd/sm501.c b/drivers/mfd/sm501.c index e7dc441a8f8a..81e6d0932bf0 100644 --- a/drivers/mfd/sm501.c +++ b/drivers/mfd/sm501.c @@ -1726,7 +1726,7 @@ static struct pci_driver sm501_pci_driver = { MODULE_ALIAS("platform:sm501"); -static struct of_device_id of_sm501_match_tbl[] = { +static const struct of_device_id of_sm501_match_tbl[] = { { .compatible = "smi,sm501", }, { /* end */ } }; diff --git a/drivers/mfd/stmpe-i2c.c b/drivers/mfd/stmpe-i2c.c index 0da02e11d58e..a45f9c0a330a 100644 --- a/drivers/mfd/stmpe-i2c.c +++ b/drivers/mfd/stmpe-i2c.c @@ -14,6 +14,7 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/types.h> +#include <linux/of_device.h> #include "stmpe.h" static int i2c_reg_read(struct stmpe *stmpe, u8 reg) @@ -52,15 +53,41 @@ static struct stmpe_client_info i2c_ci = { .write_block = i2c_block_write, }; +static const struct of_device_id stmpe_of_match[] = { + { .compatible = "st,stmpe610", .data = (void *)STMPE610, }, + { .compatible = "st,stmpe801", .data = (void *)STMPE801, }, + { .compatible = "st,stmpe811", .data = (void *)STMPE811, }, + { .compatible = "st,stmpe1601", .data = (void *)STMPE1601, }, + { .compatible = "st,stmpe1801", .data = (void *)STMPE1801, }, + { .compatible = "st,stmpe2401", .data = (void *)STMPE2401, }, + { .compatible = "st,stmpe2403", .data = (void *)STMPE2403, }, + {}, +}; +MODULE_DEVICE_TABLE(of, stmpe_of_match); + static int stmpe_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { + int partnum; + const struct of_device_id *of_id; + i2c_ci.data = (void *)id; i2c_ci.irq = i2c->irq; i2c_ci.client = i2c; i2c_ci.dev = &i2c->dev; - return stmpe_probe(&i2c_ci, id->driver_data); + of_id = of_match_device(stmpe_of_match, &i2c->dev); + if (!of_id) { + /* + * This happens when the I2C ID matches the node name + * but no real compatible string has been given. + */ + dev_info(&i2c->dev, "matching on node name, compatible is preferred\n"); + partnum = id->driver_data; + } else + partnum = (int)of_id->data; + + return stmpe_probe(&i2c_ci, partnum); } static int stmpe_i2c_remove(struct i2c_client *i2c) @@ -89,6 +116,7 @@ static struct i2c_driver stmpe_i2c_driver = { #ifdef CONFIG_PM .pm = &stmpe_dev_pm_ops, #endif + .of_match_table = stmpe_of_match, }, .probe = stmpe_i2c_probe, .remove = stmpe_i2c_remove, diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c index 4a91f6771fb8..3b6bfa7184ad 100644 --- a/drivers/mfd/stmpe.c +++ b/drivers/mfd/stmpe.c @@ -20,6 +20,7 @@ #include <linux/slab.h> #include <linux/mfd/core.h> #include <linux/delay.h> +#include <linux/regulator/consumer.h> #include "stmpe.h" static int __stmpe_enable(struct stmpe *stmpe, unsigned int blocks) @@ -605,9 +606,18 @@ static int stmpe1601_enable(struct stmpe *stmpe, unsigned int blocks, if (blocks & STMPE_BLOCK_GPIO) mask |= STMPE1601_SYS_CTRL_ENABLE_GPIO; + else + mask &= ~STMPE1601_SYS_CTRL_ENABLE_GPIO; if (blocks & STMPE_BLOCK_KEYPAD) mask |= STMPE1601_SYS_CTRL_ENABLE_KPC; + else + mask &= ~STMPE1601_SYS_CTRL_ENABLE_KPC; + + if (blocks & STMPE_BLOCK_PWM) + mask |= STMPE1601_SYS_CTRL_ENABLE_SPWM; + else + mask &= ~STMPE1601_SYS_CTRL_ENABLE_SPWM; return __stmpe_set_bits(stmpe, STMPE1601_REG_SYS_CTRL, mask, enable ? mask : 0); @@ -986,9 +996,6 @@ static int stmpe_irq_init(struct stmpe *stmpe, struct device_node *np) int base = 0; int num_irqs = stmpe->variant->num_irqs; - if (!np) - base = stmpe->irq_base; - stmpe->domain = irq_domain_add_simple(np, num_irqs, base, &stmpe_irq_ops, stmpe); if (!stmpe->domain) { @@ -1067,7 +1074,7 @@ static int stmpe_chip_init(struct stmpe *stmpe) static int stmpe_add_device(struct stmpe *stmpe, const struct mfd_cell *cell) { return mfd_add_devices(stmpe->dev, stmpe->pdata->id, cell, 1, - NULL, stmpe->irq_base, stmpe->domain); + NULL, 0, stmpe->domain); } static int stmpe_devices_init(struct stmpe *stmpe) @@ -1171,12 +1178,23 @@ int stmpe_probe(struct stmpe_client_info *ci, int partnum) stmpe->dev = ci->dev; stmpe->client = ci->client; stmpe->pdata = pdata; - stmpe->irq_base = pdata->irq_base; stmpe->ci = ci; stmpe->partnum = partnum; stmpe->variant = stmpe_variant_info[partnum]; stmpe->regs = stmpe->variant->regs; stmpe->num_gpios = stmpe->variant->num_gpios; + stmpe->vcc = devm_regulator_get_optional(ci->dev, "vcc"); + if (!IS_ERR(stmpe->vcc)) { + ret = regulator_enable(stmpe->vcc); + if (ret) + dev_warn(ci->dev, "failed to enable VCC supply\n"); + } + stmpe->vio = devm_regulator_get_optional(ci->dev, "vio"); + if (!IS_ERR(stmpe->vio)) { + ret = regulator_enable(stmpe->vio); + if (ret) + dev_warn(ci->dev, "failed to enable VIO supply\n"); + } dev_set_drvdata(stmpe->dev, stmpe); if (ci->init) @@ -1243,6 +1261,11 @@ int stmpe_probe(struct stmpe_client_info *ci, int partnum) int stmpe_remove(struct stmpe *stmpe) { + if (!IS_ERR(stmpe->vio)) + regulator_disable(stmpe->vio); + if (!IS_ERR(stmpe->vcc)) + regulator_disable(stmpe->vcc); + mfd_remove_devices(stmpe->dev); return 0; diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h index 6639f1b0fef5..9e4d21d37a11 100644 --- a/drivers/mfd/stmpe.h +++ b/drivers/mfd/stmpe.h @@ -192,7 +192,7 @@ int stmpe_remove(struct stmpe *stmpe); #define STMPE1601_SYS_CTRL_ENABLE_GPIO (1 << 3) #define STMPE1601_SYS_CTRL_ENABLE_KPC (1 << 1) -#define STMPE1601_SYSCON_ENABLE_SPWM (1 << 0) +#define STMPE1601_SYS_CTRL_ENABLE_SPWM (1 << 0) /* The 1601/2403 share the same masks */ #define STMPE1601_AUTOSLEEP_TIMEOUT_MASK (0x7) diff --git a/drivers/mfd/sun6i-prcm.c b/drivers/mfd/sun6i-prcm.c new file mode 100644 index 000000000000..718fc4d2adc0 --- /dev/null +++ b/drivers/mfd/sun6i-prcm.c @@ -0,0 +1,134 @@ +/* + * Copyright (C) 2014 Free Electrons + * + * License Terms: GNU General Public License v2 + * Author: Boris BREZILLON <boris.brezillon@free-electrons.com> + * + * Allwinner PRCM (Power/Reset/Clock Management) driver + * + */ + +#include <linux/mfd/core.h> +#include <linux/module.h> +#include <linux/of.h> + +struct prcm_data { + int nsubdevs; + const struct mfd_cell *subdevs; +}; + +static const struct resource sun6i_a31_ar100_clk_res[] = { + { + .start = 0x0, + .end = 0x3, + .flags = IORESOURCE_MEM, + }, +}; + +static const struct resource sun6i_a31_apb0_clk_res[] = { + { + .start = 0xc, + .end = 0xf, + .flags = IORESOURCE_MEM, + }, +}; + +static const struct resource sun6i_a31_apb0_gates_clk_res[] = { + { + .start = 0x28, + .end = 0x2b, + .flags = IORESOURCE_MEM, + }, +}; + +static const struct resource sun6i_a31_apb0_rstc_res[] = { + { + .start = 0xb0, + .end = 0xb3, + .flags = IORESOURCE_MEM, + }, +}; + +static const struct mfd_cell sun6i_a31_prcm_subdevs[] = { + { + .name = "sun6i-a31-ar100-clk", + .of_compatible = "allwinner,sun6i-a31-ar100-clk", + .num_resources = ARRAY_SIZE(sun6i_a31_ar100_clk_res), + .resources = sun6i_a31_ar100_clk_res, + }, + { + .name = "sun6i-a31-apb0-clk", + .of_compatible = "allwinner,sun6i-a31-apb0-clk", + .num_resources = ARRAY_SIZE(sun6i_a31_apb0_clk_res), + .resources = sun6i_a31_apb0_clk_res, + }, + { + .name = "sun6i-a31-apb0-gates-clk", + .of_compatible = "allwinner,sun6i-a31-apb0-gates-clk", + .num_resources = ARRAY_SIZE(sun6i_a31_apb0_gates_clk_res), + .resources = sun6i_a31_apb0_gates_clk_res, + }, + { + .name = "sun6i-a31-apb0-clock-reset", + .of_compatible = "allwinner,sun6i-a31-clock-reset", + .num_resources = ARRAY_SIZE(sun6i_a31_apb0_rstc_res), + .resources = sun6i_a31_apb0_rstc_res, + }, +}; + +static const struct prcm_data sun6i_a31_prcm_data = { + .nsubdevs = ARRAY_SIZE(sun6i_a31_prcm_subdevs), + .subdevs = sun6i_a31_prcm_subdevs, +}; + +static const struct of_device_id sun6i_prcm_dt_ids[] = { + { + .compatible = "allwinner,sun6i-a31-prcm", + .data = &sun6i_a31_prcm_data, + }, + { /* sentinel */ }, +}; + +static int sun6i_prcm_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + const struct of_device_id *match; + const struct prcm_data *data; + struct resource *res; + int ret; + + match = of_match_node(sun6i_prcm_dt_ids, np); + if (!match) + return -EINVAL; + + data = match->data; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "no prcm memory region provided\n"); + return -ENOENT; + } + + ret = mfd_add_devices(&pdev->dev, 0, data->subdevs, data->nsubdevs, + res, -1, NULL); + if (ret) { + dev_err(&pdev->dev, "failed to add subdevices\n"); + return ret; + } + + return 0; +} + +static struct platform_driver sun6i_prcm_driver = { + .driver = { + .name = "sun6i-prcm", + .owner = THIS_MODULE, + .of_match_table = sun6i_prcm_dt_ids, + }, + .probe = sun6i_prcm_probe, +}; +module_platform_driver(sun6i_prcm_driver); + +MODULE_AUTHOR("Boris BREZILLON <boris.brezillon@free-electrons.com>"); +MODULE_DESCRIPTION("Allwinner sun6i PRCM driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/mfd/syscon.c b/drivers/mfd/syscon.c index dbea55de4397..ca15878ce5c0 100644 --- a/drivers/mfd/syscon.c +++ b/drivers/mfd/syscon.c @@ -18,6 +18,7 @@ #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_platform.h> +#include <linux/platform_data/syscon.h> #include <linux/platform_device.h> #include <linux/regmap.h> #include <linux/mfd/syscon.h> @@ -94,7 +95,11 @@ struct regmap *syscon_regmap_lookup_by_phandle(struct device_node *np, struct device_node *syscon_np; struct regmap *regmap; - syscon_np = of_parse_phandle(np, property, 0); + if (property) + syscon_np = of_parse_phandle(np, property, 0); + else + syscon_np = np; + if (!syscon_np) return ERR_PTR(-ENODEV); @@ -119,6 +124,7 @@ static struct regmap_config syscon_regmap_config = { static int syscon_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; + struct syscon_platform_data *pdata = dev_get_platdata(dev); struct syscon *syscon; struct resource *res; void __iomem *base; @@ -136,6 +142,8 @@ static int syscon_probe(struct platform_device *pdev) return -ENOMEM; syscon_regmap_config.max_register = res->end - res->start - 3; + if (pdata) + syscon_regmap_config.name = pdata->label; syscon->regmap = devm_regmap_init_mmio(dev, base, &syscon_regmap_config); if (IS_ERR(syscon->regmap)) { diff --git a/drivers/mfd/tps6507x.c b/drivers/mfd/tps6507x.c index 3b27482a174f..a2e1990c9de7 100644 --- a/drivers/mfd/tps6507x.c +++ b/drivers/mfd/tps6507x.c @@ -119,7 +119,7 @@ static const struct i2c_device_id tps6507x_i2c_id[] = { MODULE_DEVICE_TABLE(i2c, tps6507x_i2c_id); #ifdef CONFIG_OF -static struct of_device_id tps6507x_of_match[] = { +static const struct of_device_id tps6507x_of_match[] = { {.compatible = "ti,tps6507x", }, {}, }; diff --git a/drivers/mfd/tps65218.c b/drivers/mfd/tps65218.c index a74bfb59f18f..0d256cb002eb 100644 --- a/drivers/mfd/tps65218.c +++ b/drivers/mfd/tps65218.c @@ -197,6 +197,7 @@ static struct regmap_irq_chip tps65218_irq_chip = { static const struct of_device_id of_tps65218_match_table[] = { { .compatible = "ti,tps65218", }, + {} }; static int tps65218_probe(struct i2c_client *client, diff --git a/drivers/mfd/tps6586x.c b/drivers/mfd/tps6586x.c index 835e5549ecdd..8e1dbc469580 100644 --- a/drivers/mfd/tps6586x.c +++ b/drivers/mfd/tps6586x.c @@ -444,7 +444,7 @@ static struct tps6586x_platform_data *tps6586x_parse_dt(struct i2c_client *clien return pdata; } -static struct of_device_id tps6586x_of_match[] = { +static const struct of_device_id tps6586x_of_match[] = { { .compatible = "ti,tps6586x", }, { }, }; diff --git a/drivers/mfd/tps65910.c b/drivers/mfd/tps65910.c index 460a014ca629..f9e42ea1cb1a 100644 --- a/drivers/mfd/tps65910.c +++ b/drivers/mfd/tps65910.c @@ -379,7 +379,7 @@ err_sleep_init: } #ifdef CONFIG_OF -static struct of_device_id tps65910_of_match[] = { +static const struct of_device_id tps65910_of_match[] = { { .compatible = "ti,tps65910", .data = (void *)TPS65910}, { .compatible = "ti,tps65911", .data = (void *)TPS65911}, { }, diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c index e87140bef667..db11b4f40611 100644 --- a/drivers/mfd/twl-core.c +++ b/drivers/mfd/twl-core.c @@ -98,7 +98,11 @@ #define TWL4030_BASEADD_BACKUP 0x0014 #define TWL4030_BASEADD_INT 0x002E #define TWL4030_BASEADD_PM_MASTER 0x0036 + #define TWL4030_BASEADD_PM_RECEIVER 0x005B +#define TWL4030_DCDC_GLOBAL_CFG 0x06 +#define SMARTREFLEX_ENABLE BIT(3) + #define TWL4030_BASEADD_RTC 0x001C #define TWL4030_BASEADD_SECURED_REG 0x0000 @@ -1204,6 +1208,11 @@ twl_probe(struct i2c_client *client, const struct i2c_device_id *id) * Disable TWL4030/TWL5030 I2C Pull-up on I2C1 and I2C4(SR) interface. * Program I2C_SCL_CTRL_PU(bit 0)=0, I2C_SDA_CTRL_PU (bit 2)=0, * SR_I2C_SCL_CTRL_PU(bit 4)=0 and SR_I2C_SDA_CTRL_PU(bit 6)=0. + * + * Also, always enable SmartReflex bit as that's needed for omaps to + * to do anything over I2C4 for voltage scaling even if SmartReflex + * is disabled. Without the SmartReflex bit omap sys_clkreq idle + * signal will never trigger for retention idle. */ if (twl_class_is_4030()) { u8 temp; @@ -1212,6 +1221,12 @@ twl_probe(struct i2c_client *client, const struct i2c_device_id *id) temp &= ~(SR_I2C_SDA_CTRL_PU | SR_I2C_SCL_CTRL_PU | \ I2C_SDA_CTRL_PU | I2C_SCL_CTRL_PU); twl_i2c_write_u8(TWL4030_MODULE_INTBR, temp, REG_GPPUPDCTR1); + + twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &temp, + TWL4030_DCDC_GLOBAL_CFG); + temp |= SMARTREFLEX_ENABLE; + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, temp, + TWL4030_DCDC_GLOBAL_CFG); } if (node) { diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 96162b62f3c0..3bc969a5916b 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -29,13 +29,21 @@ #include <linux/i2c/twl.h> #include <linux/platform_device.h> #include <linux/of.h> +#include <linux/of_device.h> #include <asm/mach-types.h> static u8 twl4030_start_script_address = 0x2b; -#define PWR_P1_SW_EVENTS 0x10 -#define PWR_DEVOFF (1 << 0) +/* Register bits for P1, P2 and P3_SW_EVENTS */ +#define PWR_STOPON_PRWON BIT(6) +#define PWR_STOPON_SYSEN BIT(5) +#define PWR_ENABLE_WARMRESET BIT(4) +#define PWR_LVL_WAKEUP BIT(3) +#define PWR_DEVACT BIT(2) +#define PWR_DEVSLP BIT(1) +#define PWR_DEVOFF BIT(0) + #define SEQ_OFFSYNC (1 << 0) #define PHY_TO_OFF_PM_MASTER(p) (p - 0x36) @@ -52,10 +60,6 @@ static u8 twl4030_start_script_address = 0x2b; #define R_CFG_P2_TRANSITION PHY_TO_OFF_PM_MASTER(0x37) #define R_CFG_P3_TRANSITION PHY_TO_OFF_PM_MASTER(0x38) -#define LVL_WAKEUP 0x08 - -#define ENABLE_WARMRESET (1<<4) - #define END_OF_SCRIPT 0x3f #define R_SEQ_ADD_A2S PHY_TO_OFF_PM_MASTER(0x55) @@ -125,6 +129,53 @@ static u8 res_config_addrs[] = { [RES_MAIN_REF] = 0x94, }; +/* + * Usable values for .remap_sleep and .remap_off + * Based on table "5.3.3 Resource Operating modes" + */ +enum { + TWL_REMAP_OFF = 0, + TWL_REMAP_SLEEP = 8, + TWL_REMAP_ACTIVE = 9, +}; + +/* + * Macros to configure the PM register states for various resources. + * Note that we can make MSG_SINGULAR etc private to this driver once + * omap3 has been made DT only. + */ +#define TWL_DFLT_DELAY 2 /* typically 2 32 KiHz cycles */ +#define TWL_DEV_GRP_P123 (DEV_GRP_P1 | DEV_GRP_P2 | DEV_GRP_P3) +#define TWL_RESOURCE_SET(res, state) \ + { MSG_SINGULAR(DEV_GRP_NULL, (res), (state)), TWL_DFLT_DELAY } +#define TWL_RESOURCE_ON(res) TWL_RESOURCE_SET(res, RES_STATE_ACTIVE) +#define TWL_RESOURCE_OFF(res) TWL_RESOURCE_SET(res, RES_STATE_OFF) +#define TWL_RESOURCE_RESET(res) TWL_RESOURCE_SET(res, RES_STATE_WRST) +/* + * It seems that type1 and type2 is just the resource init order + * number for the type1 and type2 group. + */ +#define TWL_RESOURCE_SET_ACTIVE(res, state) \ + { MSG_SINGULAR(DEV_GRP_NULL, (res), RES_STATE_ACTIVE), (state) } +#define TWL_RESOURCE_GROUP_RESET(group, type1, type2) \ + { MSG_BROADCAST(DEV_GRP_NULL, (group), (type1), (type2), \ + RES_STATE_WRST), TWL_DFLT_DELAY } +#define TWL_RESOURCE_GROUP_SLEEP(group, type, type2) \ + { MSG_BROADCAST(DEV_GRP_NULL, (group), (type), (type2), \ + RES_STATE_SLEEP), TWL_DFLT_DELAY } +#define TWL_RESOURCE_GROUP_ACTIVE(group, type, type2) \ + { MSG_BROADCAST(DEV_GRP_NULL, (group), (type), (type2), \ + RES_STATE_ACTIVE), TWL_DFLT_DELAY } +#define TWL_REMAP_SLEEP(res, devgrp, typ, typ2) \ + { .resource = (res), .devgroup = (devgrp), \ + .type = (typ), .type2 = (typ2), \ + .remap_off = TWL_REMAP_OFF, \ + .remap_sleep = TWL_REMAP_SLEEP, } +#define TWL_REMAP_OFF(res, devgrp, typ, typ2) \ + { .resource = (res), .devgroup = (devgrp), \ + .type = (typ), .type2 = (typ2), \ + .remap_off = TWL_REMAP_OFF, .remap_sleep = TWL_REMAP_OFF, } + static int twl4030_write_script_byte(u8 address, u8 byte) { int err; @@ -196,7 +247,7 @@ static int twl4030_config_wakeup3_sequence(u8 address) err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &data, R_P3_SW_EVENTS); if (err) goto out; - data |= LVL_WAKEUP; + data |= PWR_LVL_WAKEUP; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P3_SW_EVENTS); out: if (err) @@ -219,7 +270,7 @@ static int twl4030_config_wakeup12_sequence(u8 address) if (err) goto out; - data |= LVL_WAKEUP; + data |= PWR_LVL_WAKEUP; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P1_SW_EVENTS); if (err) goto out; @@ -228,7 +279,7 @@ static int twl4030_config_wakeup12_sequence(u8 address) if (err) goto out; - data |= LVL_WAKEUP; + data |= PWR_LVL_WAKEUP; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P2_SW_EVENTS); if (err) goto out; @@ -281,7 +332,7 @@ static int twl4030_config_warmreset_sequence(u8 address) if (err) goto out; - rd_data |= ENABLE_WARMRESET; + rd_data |= PWR_ENABLE_WARMRESET; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P1_SW_EVENTS); if (err) goto out; @@ -290,7 +341,7 @@ static int twl4030_config_warmreset_sequence(u8 address) if (err) goto out; - rd_data |= ENABLE_WARMRESET; + rd_data |= PWR_ENABLE_WARMRESET; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P2_SW_EVENTS); if (err) goto out; @@ -299,7 +350,7 @@ static int twl4030_config_warmreset_sequence(u8 address) if (err) goto out; - rd_data |= ENABLE_WARMRESET; + rd_data |= PWR_ENABLE_WARMRESET; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P3_SW_EVENTS); out: if (err) @@ -421,6 +472,12 @@ static int load_twl4030_script(struct twl4030_script *tscript, goto out; } if (tscript->flags & TWL4030_WAKEUP12_SCRIPT) { + /* Reset any existing sleep script to avoid hangs on reboot */ + err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, END_OF_SCRIPT, + R_SEQ_ADD_A2S); + if (err) + goto out; + err = twl4030_config_wakeup12_sequence(address); if (err) goto out; @@ -493,7 +550,8 @@ int twl4030_remove_script(u8 flags) return err; } -static int twl4030_power_configure_scripts(struct twl4030_power_data *pdata) +static int +twl4030_power_configure_scripts(const struct twl4030_power_data *pdata) { int err; int i; @@ -509,12 +567,34 @@ static int twl4030_power_configure_scripts(struct twl4030_power_data *pdata) return 0; } -static int twl4030_power_configure_resources(struct twl4030_power_data *pdata) +static void twl4030_patch_rconfig(struct twl4030_resconfig *common, + struct twl4030_resconfig *board) +{ + while (common->resource) { + struct twl4030_resconfig *b = board; + + while (b->resource) { + if (b->resource == common->resource) { + *common = *b; + break; + } + b++; + } + common++; + } +} + +static int +twl4030_power_configure_resources(const struct twl4030_power_data *pdata) { struct twl4030_resconfig *resconfig = pdata->resource_config; + struct twl4030_resconfig *boardconf = pdata->board_config; int err; if (resconfig) { + if (boardconf) + twl4030_patch_rconfig(resconfig, boardconf); + while (resconfig->resource) { err = twl4030_configure_resource(resconfig); if (err) @@ -541,7 +621,7 @@ void twl4030_power_off(void) pr_err("TWL4030 Unable to power off\n"); } -static bool twl4030_power_use_poweroff(struct twl4030_power_data *pdata, +static bool twl4030_power_use_poweroff(const struct twl4030_power_data *pdata, struct device_node *node) { if (pdata && pdata->use_poweroff) @@ -553,10 +633,170 @@ static bool twl4030_power_use_poweroff(struct twl4030_power_data *pdata, return false; } +#ifdef CONFIG_OF + +/* Generic warm reset configuration for omap3 */ + +static struct twl4030_ins omap3_wrst_seq[] = { + TWL_RESOURCE_OFF(RES_NRES_PWRON), + TWL_RESOURCE_OFF(RES_RESET), + TWL_RESOURCE_RESET(RES_MAIN_REF), + TWL_RESOURCE_GROUP_RESET(RES_GRP_ALL, RES_TYPE_R0, RES_TYPE2_R2), + TWL_RESOURCE_RESET(RES_VUSB_3V1), + TWL_RESOURCE_GROUP_RESET(RES_GRP_ALL, RES_TYPE_R0, RES_TYPE2_R1), + TWL_RESOURCE_GROUP_RESET(RES_GRP_RC, RES_TYPE_ALL, RES_TYPE2_R0), + TWL_RESOURCE_ON(RES_RESET), + TWL_RESOURCE_ON(RES_NRES_PWRON), +}; + +static struct twl4030_script omap3_wrst_script = { + .script = omap3_wrst_seq, + .size = ARRAY_SIZE(omap3_wrst_seq), + .flags = TWL4030_WRST_SCRIPT, +}; + +static struct twl4030_script *omap3_reset_scripts[] = { + &omap3_wrst_script, +}; + +static struct twl4030_resconfig omap3_rconfig[] = { + TWL_REMAP_SLEEP(RES_HFCLKOUT, DEV_GRP_P3, -1, -1), + TWL_REMAP_SLEEP(RES_VDD1, DEV_GRP_P1, -1, -1), + TWL_REMAP_SLEEP(RES_VDD2, DEV_GRP_P1, -1, -1), + { 0, 0 }, +}; + +static struct twl4030_power_data omap3_reset = { + .scripts = omap3_reset_scripts, + .num = ARRAY_SIZE(omap3_reset_scripts), + .resource_config = omap3_rconfig, +}; + +/* Recommended generic default idle configuration for off-idle */ + +/* Broadcast message to put res to sleep */ +static struct twl4030_ins omap3_idle_sleep_on_seq[] = { + TWL_RESOURCE_GROUP_SLEEP(RES_GRP_ALL, RES_TYPE_ALL, 0), +}; + +static struct twl4030_script omap3_idle_sleep_on_script = { + .script = omap3_idle_sleep_on_seq, + .size = ARRAY_SIZE(omap3_idle_sleep_on_seq), + .flags = TWL4030_SLEEP_SCRIPT, +}; + +/* Broadcast message to put res to active */ +static struct twl4030_ins omap3_idle_wakeup_p12_seq[] = { + TWL_RESOURCE_GROUP_ACTIVE(RES_GRP_ALL, RES_TYPE_ALL, 0), +}; + +static struct twl4030_script omap3_idle_wakeup_p12_script = { + .script = omap3_idle_wakeup_p12_seq, + .size = ARRAY_SIZE(omap3_idle_wakeup_p12_seq), + .flags = TWL4030_WAKEUP12_SCRIPT, +}; + +/* Broadcast message to put res to active */ +static struct twl4030_ins omap3_idle_wakeup_p3_seq[] = { + TWL_RESOURCE_SET_ACTIVE(RES_CLKEN, 0x37), + TWL_RESOURCE_GROUP_ACTIVE(RES_GRP_ALL, RES_TYPE_ALL, 0), +}; + +static struct twl4030_script omap3_idle_wakeup_p3_script = { + .script = omap3_idle_wakeup_p3_seq, + .size = ARRAY_SIZE(omap3_idle_wakeup_p3_seq), + .flags = TWL4030_WAKEUP3_SCRIPT, +}; + +static struct twl4030_script *omap3_idle_scripts[] = { + &omap3_idle_wakeup_p12_script, + &omap3_idle_wakeup_p3_script, + &omap3_wrst_script, + &omap3_idle_sleep_on_script, +}; + +/* + * Recommended configuration based on "Recommended Sleep + * Sequences for the Zoom Platform": + * http://omappedia.com/wiki/File:Recommended_Sleep_Sequences_Zoom.pdf + * Note that the type1 and type2 seem to be just the init order number + * for type1 and type2 groups as specified in the document mentioned + * above. + */ +static struct twl4030_resconfig omap3_idle_rconfig[] = { + TWL_REMAP_SLEEP(RES_VAUX1, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VAUX2, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VAUX3, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VAUX4, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VMMC1, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VMMC2, DEV_GRP_NULL, 0, 0), + TWL_REMAP_OFF(RES_VPLL1, DEV_GRP_P1, 3, 1), + TWL_REMAP_SLEEP(RES_VPLL2, DEV_GRP_P1, 0, 0), + TWL_REMAP_SLEEP(RES_VSIM, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VDAC, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VINTANA1, TWL_DEV_GRP_P123, 1, 2), + TWL_REMAP_SLEEP(RES_VINTANA2, TWL_DEV_GRP_P123, 0, 2), + TWL_REMAP_SLEEP(RES_VINTDIG, TWL_DEV_GRP_P123, 1, 2), + TWL_REMAP_SLEEP(RES_VIO, TWL_DEV_GRP_P123, 2, 2), + TWL_REMAP_OFF(RES_VDD1, DEV_GRP_P1, 4, 1), + TWL_REMAP_OFF(RES_VDD2, DEV_GRP_P1, 3, 1), + TWL_REMAP_SLEEP(RES_VUSB_1V5, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VUSB_1V8, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VUSB_3V1, TWL_DEV_GRP_P123, 0, 0), + /* Resource #20 USB charge pump skipped */ + TWL_REMAP_SLEEP(RES_REGEN, TWL_DEV_GRP_P123, 2, 1), + TWL_REMAP_SLEEP(RES_NRES_PWRON, TWL_DEV_GRP_P123, 0, 1), + TWL_REMAP_SLEEP(RES_CLKEN, TWL_DEV_GRP_P123, 3, 2), + TWL_REMAP_SLEEP(RES_SYSEN, TWL_DEV_GRP_P123, 6, 1), + TWL_REMAP_SLEEP(RES_HFCLKOUT, DEV_GRP_P3, 0, 2), + TWL_REMAP_SLEEP(RES_32KCLKOUT, TWL_DEV_GRP_P123, 0, 0), + TWL_REMAP_SLEEP(RES_RESET, TWL_DEV_GRP_P123, 6, 0), + TWL_REMAP_SLEEP(RES_MAIN_REF, TWL_DEV_GRP_P123, 0, 0), + { /* Terminator */ }, +}; + +static struct twl4030_power_data omap3_idle = { + .scripts = omap3_idle_scripts, + .num = ARRAY_SIZE(omap3_idle_scripts), + .resource_config = omap3_idle_rconfig, +}; + +/* Disable 32 KiHz oscillator during idle */ +static struct twl4030_resconfig osc_off_rconfig[] = { + TWL_REMAP_OFF(RES_CLKEN, DEV_GRP_P1 | DEV_GRP_P3, 3, 2), + { /* Terminator */ }, +}; + +static struct twl4030_power_data osc_off_idle = { + .scripts = omap3_idle_scripts, + .num = ARRAY_SIZE(omap3_idle_scripts), + .resource_config = omap3_idle_rconfig, + .board_config = osc_off_rconfig, +}; + +static struct of_device_id twl4030_power_of_match[] = { + { + .compatible = "ti,twl4030-power-reset", + .data = &omap3_reset, + }, + { + .compatible = "ti,twl4030-power-idle", + .data = &omap3_idle, + }, + { + .compatible = "ti,twl4030-power-idle-osc-off", + .data = &osc_off_idle, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, twl4030_power_of_match); +#endif /* CONFIG_OF */ + static int twl4030_power_probe(struct platform_device *pdev) { - struct twl4030_power_data *pdata = dev_get_platdata(&pdev->dev); + const struct twl4030_power_data *pdata = dev_get_platdata(&pdev->dev); struct device_node *node = pdev->dev.of_node; + const struct of_device_id *match; int err = 0; int err2 = 0; u8 val; @@ -577,8 +817,12 @@ static int twl4030_power_probe(struct platform_device *pdev) return err; } + match = of_match_device(of_match_ptr(twl4030_power_of_match), + &pdev->dev); + if (match && match->data) + pdata = match->data; + if (pdata) { - /* TODO: convert to device tree */ err = twl4030_power_configure_scripts(pdata); if (err) { pr_err("TWL4030 failed to load scripts\n"); @@ -628,14 +872,6 @@ static int twl4030_power_remove(struct platform_device *pdev) return 0; } -#ifdef CONFIG_OF -static const struct of_device_id twl4030_power_of_match[] = { - {.compatible = "ti,twl4030-power", }, - { }, -}; -MODULE_DEVICE_TABLE(of, twl4030_power_of_match); -#endif - static struct platform_driver twl4030_power_driver = { .driver = { .name = "twl4030_power", diff --git a/drivers/mfd/twl6040.c b/drivers/mfd/twl6040.c index 6e88f25832fb..ae26d84b3a59 100644 --- a/drivers/mfd/twl6040.c +++ b/drivers/mfd/twl6040.c @@ -87,8 +87,13 @@ static struct reg_default twl6040_defaults[] = { }; static struct reg_default twl6040_patch[] = { - /* Select I2C bus access to dual access registers */ - { TWL6040_REG_ACCCTL, 0x09 }, + /* + * Select I2C bus access to dual access registers + * Interrupt register is cleared on read + * Select fast mode for i2c (400KHz) + */ + { TWL6040_REG_ACCCTL, + TWL6040_I2CSEL | TWL6040_INTCLRMODE | TWL6040_I2CMODE(1) }, }; @@ -286,6 +291,8 @@ int twl6040_power(struct twl6040 *twl6040, int on) if (twl6040->power_count++) goto out; + clk_prepare_enable(twl6040->clk32k); + /* Allow writes to the chip */ regcache_cache_only(twl6040->regmap, false); @@ -341,6 +348,8 @@ int twl6040_power(struct twl6040 *twl6040, int on) twl6040->sysclk = 0; twl6040->mclk = 0; + + clk_disable_unprepare(twl6040->clk32k); } out: @@ -432,12 +441,9 @@ int twl6040_set_pll(struct twl6040 *twl6040, int pll_id, TWL6040_HPLLENA; break; case 19200000: - /* - * PLL disabled - * (enable PLL if MCLK jitter quality - * doesn't meet specification) - */ - hppllctl |= TWL6040_MCLK_19200KHZ; + /* PLL enabled, bypass mode */ + hppllctl |= TWL6040_MCLK_19200KHZ | + TWL6040_HPLLBP | TWL6040_HPLLENA; break; case 26000000: /* PLL enabled, active mode */ @@ -445,9 +451,9 @@ int twl6040_set_pll(struct twl6040 *twl6040, int pll_id, TWL6040_HPLLENA; break; case 38400000: - /* PLL enabled, active mode */ + /* PLL enabled, bypass mode */ hppllctl |= TWL6040_MCLK_38400KHZ | - TWL6040_HPLLENA; + TWL6040_HPLLBP | TWL6040_HPLLENA; break; default: dev_err(twl6040->dev, @@ -639,6 +645,12 @@ static int twl6040_probe(struct i2c_client *client, i2c_set_clientdata(client, twl6040); + twl6040->clk32k = devm_clk_get(&client->dev, "clk32k"); + if (IS_ERR(twl6040->clk32k)) { + dev_info(&client->dev, "clk32k is not handled\n"); + twl6040->clk32k = NULL; + } + twl6040->supplies[0].supply = "vio"; twl6040->supplies[1].supply = "v2v1"; ret = devm_regulator_bulk_get(&client->dev, TWL6040_NUM_SUPPLIES, @@ -660,6 +672,9 @@ static int twl6040_probe(struct i2c_client *client, mutex_init(&twl6040->mutex); init_completion(&twl6040->ready); + regmap_register_patch(twl6040->regmap, twl6040_patch, + ARRAY_SIZE(twl6040_patch)); + twl6040->rev = twl6040_reg_read(twl6040, TWL6040_REG_ASICREV); if (twl6040->rev < 0) { dev_err(&client->dev, "Failed to read revision register: %d\n", @@ -679,6 +694,9 @@ static int twl6040_probe(struct i2c_client *client, GPIOF_OUT_INIT_LOW, "audpwron"); if (ret) goto gpio_err; + + /* Clear any pending interrupt */ + twl6040_reg_read(twl6040, TWL6040_REG_INTID); } ret = regmap_add_irq_chip(twl6040->regmap, twl6040->irq, IRQF_ONESHOT, @@ -707,10 +725,6 @@ static int twl6040_probe(struct i2c_client *client, goto readyirq_err; } - /* dual-access registers controlled by I2C only */ - regmap_register_patch(twl6040->regmap, twl6040_patch, - ARRAY_SIZE(twl6040_patch)); - /* * The main functionality of twl6040 to provide audio on OMAP4+ systems. * We can add the ASoC codec child whenever this driver has been loaded. diff --git a/drivers/mfd/vexpress-config.c b/drivers/mfd/vexpress-config.c deleted file mode 100644 index d0db89d13e01..000000000000 --- a/drivers/mfd/vexpress-config.c +++ /dev/null @@ -1,287 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Copyright (C) 2012 ARM Limited - */ - -#define pr_fmt(fmt) "vexpress-config: " fmt - -#include <linux/bitops.h> -#include <linux/completion.h> -#include <linux/export.h> -#include <linux/list.h> -#include <linux/of.h> -#include <linux/of_device.h> -#include <linux/slab.h> -#include <linux/string.h> -#include <linux/vexpress.h> - - -#define VEXPRESS_CONFIG_MAX_BRIDGES 2 - -static struct vexpress_config_bridge { - struct device_node *node; - struct vexpress_config_bridge_info *info; - struct list_head transactions; - spinlock_t transactions_lock; -} vexpress_config_bridges[VEXPRESS_CONFIG_MAX_BRIDGES]; - -static DECLARE_BITMAP(vexpress_config_bridges_map, - ARRAY_SIZE(vexpress_config_bridges)); -static DEFINE_MUTEX(vexpress_config_bridges_mutex); - -struct vexpress_config_bridge *vexpress_config_bridge_register( - struct device_node *node, - struct vexpress_config_bridge_info *info) -{ - struct vexpress_config_bridge *bridge; - int i; - - pr_debug("Registering bridge '%s'\n", info->name); - - mutex_lock(&vexpress_config_bridges_mutex); - i = find_first_zero_bit(vexpress_config_bridges_map, - ARRAY_SIZE(vexpress_config_bridges)); - if (i >= ARRAY_SIZE(vexpress_config_bridges)) { - pr_err("Can't register more bridges!\n"); - mutex_unlock(&vexpress_config_bridges_mutex); - return NULL; - } - __set_bit(i, vexpress_config_bridges_map); - bridge = &vexpress_config_bridges[i]; - - bridge->node = node; - bridge->info = info; - INIT_LIST_HEAD(&bridge->transactions); - spin_lock_init(&bridge->transactions_lock); - - mutex_unlock(&vexpress_config_bridges_mutex); - - return bridge; -} -EXPORT_SYMBOL(vexpress_config_bridge_register); - -void vexpress_config_bridge_unregister(struct vexpress_config_bridge *bridge) -{ - struct vexpress_config_bridge __bridge = *bridge; - int i; - - mutex_lock(&vexpress_config_bridges_mutex); - for (i = 0; i < ARRAY_SIZE(vexpress_config_bridges); i++) - if (&vexpress_config_bridges[i] == bridge) - __clear_bit(i, vexpress_config_bridges_map); - mutex_unlock(&vexpress_config_bridges_mutex); - - WARN_ON(!list_empty(&__bridge.transactions)); - while (!list_empty(&__bridge.transactions)) - cpu_relax(); -} -EXPORT_SYMBOL(vexpress_config_bridge_unregister); - - -struct vexpress_config_func { - struct vexpress_config_bridge *bridge; - void *func; -}; - -struct vexpress_config_func *__vexpress_config_func_get(struct device *dev, - struct device_node *node) -{ - struct device_node *bridge_node; - struct vexpress_config_func *func; - int i; - - if (WARN_ON(dev && node && dev->of_node != node)) - return NULL; - if (dev && !node) - node = dev->of_node; - - func = kzalloc(sizeof(*func), GFP_KERNEL); - if (!func) - return NULL; - - bridge_node = of_node_get(node); - while (bridge_node) { - const __be32 *prop = of_get_property(bridge_node, - "arm,vexpress,config-bridge", NULL); - - if (prop) { - bridge_node = of_find_node_by_phandle( - be32_to_cpup(prop)); - break; - } - - bridge_node = of_get_next_parent(bridge_node); - } - - mutex_lock(&vexpress_config_bridges_mutex); - for (i = 0; i < ARRAY_SIZE(vexpress_config_bridges); i++) { - struct vexpress_config_bridge *bridge = - &vexpress_config_bridges[i]; - - if (test_bit(i, vexpress_config_bridges_map) && - bridge->node == bridge_node) { - func->bridge = bridge; - func->func = bridge->info->func_get(dev, node); - break; - } - } - mutex_unlock(&vexpress_config_bridges_mutex); - - if (!func->func) { - of_node_put(node); - kfree(func); - return NULL; - } - - return func; -} -EXPORT_SYMBOL(__vexpress_config_func_get); - -void vexpress_config_func_put(struct vexpress_config_func *func) -{ - func->bridge->info->func_put(func->func); - of_node_put(func->bridge->node); - kfree(func); -} -EXPORT_SYMBOL(vexpress_config_func_put); - -struct vexpress_config_trans { - struct vexpress_config_func *func; - int offset; - bool write; - u32 *data; - int status; - struct completion completion; - struct list_head list; -}; - -static void vexpress_config_dump_trans(const char *what, - struct vexpress_config_trans *trans) -{ - pr_debug("%s %s trans %p func 0x%p offset %d data 0x%x status %d\n", - what, trans->write ? "write" : "read", trans, - trans->func->func, trans->offset, - trans->data ? *trans->data : 0, trans->status); -} - -static int vexpress_config_schedule(struct vexpress_config_trans *trans) -{ - int status; - struct vexpress_config_bridge *bridge = trans->func->bridge; - unsigned long flags; - - init_completion(&trans->completion); - trans->status = -EFAULT; - - spin_lock_irqsave(&bridge->transactions_lock, flags); - - if (list_empty(&bridge->transactions)) { - vexpress_config_dump_trans("Executing", trans); - status = bridge->info->func_exec(trans->func->func, - trans->offset, trans->write, trans->data); - } else { - vexpress_config_dump_trans("Queuing", trans); - status = VEXPRESS_CONFIG_STATUS_WAIT; - } - - switch (status) { - case VEXPRESS_CONFIG_STATUS_DONE: - vexpress_config_dump_trans("Finished", trans); - trans->status = status; - break; - case VEXPRESS_CONFIG_STATUS_WAIT: - list_add_tail(&trans->list, &bridge->transactions); - break; - } - - spin_unlock_irqrestore(&bridge->transactions_lock, flags); - - return status; -} - -void vexpress_config_complete(struct vexpress_config_bridge *bridge, - int status) -{ - struct vexpress_config_trans *trans; - unsigned long flags; - const char *message = "Completed"; - - spin_lock_irqsave(&bridge->transactions_lock, flags); - - trans = list_first_entry(&bridge->transactions, - struct vexpress_config_trans, list); - trans->status = status; - - do { - vexpress_config_dump_trans(message, trans); - list_del(&trans->list); - complete(&trans->completion); - - if (list_empty(&bridge->transactions)) - break; - - trans = list_first_entry(&bridge->transactions, - struct vexpress_config_trans, list); - vexpress_config_dump_trans("Executing pending", trans); - trans->status = bridge->info->func_exec(trans->func->func, - trans->offset, trans->write, trans->data); - message = "Finished pending"; - } while (trans->status == VEXPRESS_CONFIG_STATUS_DONE); - - spin_unlock_irqrestore(&bridge->transactions_lock, flags); -} -EXPORT_SYMBOL(vexpress_config_complete); - -int vexpress_config_wait(struct vexpress_config_trans *trans) -{ - wait_for_completion(&trans->completion); - - return trans->status; -} -EXPORT_SYMBOL(vexpress_config_wait); - -int vexpress_config_read(struct vexpress_config_func *func, int offset, - u32 *data) -{ - struct vexpress_config_trans trans = { - .func = func, - .offset = offset, - .write = false, - .data = data, - .status = 0, - }; - int status = vexpress_config_schedule(&trans); - - if (status == VEXPRESS_CONFIG_STATUS_WAIT) - status = vexpress_config_wait(&trans); - - return status; -} -EXPORT_SYMBOL(vexpress_config_read); - -int vexpress_config_write(struct vexpress_config_func *func, int offset, - u32 data) -{ - struct vexpress_config_trans trans = { - .func = func, - .offset = offset, - .write = true, - .data = &data, - .status = 0, - }; - int status = vexpress_config_schedule(&trans); - - if (status == VEXPRESS_CONFIG_STATUS_WAIT) - status = vexpress_config_wait(&trans); - - return status; -} -EXPORT_SYMBOL(vexpress_config_write); diff --git a/drivers/mfd/vexpress-sysreg.c b/drivers/mfd/vexpress-sysreg.c index 35281e804e7e..9e21e4fc9599 100644 --- a/drivers/mfd/vexpress-sysreg.c +++ b/drivers/mfd/vexpress-sysreg.c @@ -11,23 +11,22 @@ * Copyright (C) 2012 ARM Limited */ +#include <linux/basic_mmio_gpio.h> #include <linux/err.h> -#include <linux/gpio.h> #include <linux/io.h> -#include <linux/leds.h> +#include <linux/mfd/core.h> #include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/platform_data/syscon.h> #include <linux/platform_device.h> -#include <linux/regulator/driver.h> #include <linux/slab.h> #include <linux/stat.h> -#include <linux/timer.h> #include <linux/vexpress.h> #define SYS_ID 0x000 #define SYS_SW 0x004 #define SYS_LED 0x008 #define SYS_100HZ 0x024 -#define SYS_FLAGS 0x030 #define SYS_FLAGSSET 0x030 #define SYS_FLAGSCLR 0x034 #define SYS_NVFLAGS 0x038 @@ -46,465 +45,209 @@ #define SYS_CFGSTAT 0x0a8 #define SYS_HBI_MASK 0xfff -#define SYS_ID_HBI_SHIFT 16 #define SYS_PROCIDx_HBI_SHIFT 0 -#define SYS_LED_LED(n) (1 << (n)) - #define SYS_MCI_CARDIN (1 << 0) #define SYS_MCI_WPROT (1 << 1) -#define SYS_FLASH_WPn (1 << 0) - #define SYS_MISC_MASTERSITE (1 << 14) -#define SYS_CFGCTRL_START (1 << 31) -#define SYS_CFGCTRL_WRITE (1 << 30) -#define SYS_CFGCTRL_DCC(n) (((n) & 0xf) << 26) -#define SYS_CFGCTRL_FUNC(n) (((n) & 0x3f) << 20) -#define SYS_CFGCTRL_SITE(n) (((n) & 0x3) << 16) -#define SYS_CFGCTRL_POSITION(n) (((n) & 0xf) << 12) -#define SYS_CFGCTRL_DEVICE(n) (((n) & 0xfff) << 0) - -#define SYS_CFGSTAT_ERR (1 << 1) -#define SYS_CFGSTAT_COMPLETE (1 << 0) - - -static void __iomem *vexpress_sysreg_base; -static struct device *vexpress_sysreg_dev; -static int vexpress_master_site; - -void vexpress_flags_set(u32 data) -{ - writel(~0, vexpress_sysreg_base + SYS_FLAGSCLR); - writel(data, vexpress_sysreg_base + SYS_FLAGSSET); -} +static void __iomem *__vexpress_sysreg_base; -u32 vexpress_get_procid(int site) +static void __iomem *vexpress_sysreg_base(void) { - if (site == VEXPRESS_SITE_MASTER) - site = vexpress_master_site; - - return readl(vexpress_sysreg_base + (site == VEXPRESS_SITE_DB1 ? - SYS_PROCID0 : SYS_PROCID1)); -} + if (!__vexpress_sysreg_base) { + struct device_node *node = of_find_compatible_node(NULL, NULL, + "arm,vexpress-sysreg"); -u32 vexpress_get_hbi(int site) -{ - u32 id; - - switch (site) { - case VEXPRESS_SITE_MB: - id = readl(vexpress_sysreg_base + SYS_ID); - return (id >> SYS_ID_HBI_SHIFT) & SYS_HBI_MASK; - case VEXPRESS_SITE_MASTER: - case VEXPRESS_SITE_DB1: - case VEXPRESS_SITE_DB2: - id = vexpress_get_procid(site); - return (id >> SYS_PROCIDx_HBI_SHIFT) & SYS_HBI_MASK; + __vexpress_sysreg_base = of_iomap(node, 0); } - return ~0; -} + WARN_ON(!__vexpress_sysreg_base); -void __iomem *vexpress_get_24mhz_clock_base(void) -{ - return vexpress_sysreg_base + SYS_24MHZ; + return __vexpress_sysreg_base; } -static void vexpress_sysreg_find_prop(struct device_node *node, - const char *name, u32 *val) +static int vexpress_sysreg_get_master(void) { - of_node_get(node); - while (node) { - if (of_property_read_u32(node, name, val) == 0) { - of_node_put(node); - return; - } - node = of_get_next_parent(node); - } -} - -unsigned __vexpress_get_site(struct device *dev, struct device_node *node) -{ - u32 site = 0; - - WARN_ON(dev && node && dev->of_node != node); - if (dev && !node) - node = dev->of_node; - - if (node) { - vexpress_sysreg_find_prop(node, "arm,vexpress,site", &site); - } else if (dev && dev->bus == &platform_bus_type) { - struct platform_device *pdev = to_platform_device(dev); - - if (pdev->num_resources == 1 && - pdev->resource[0].flags == IORESOURCE_BUS) - site = pdev->resource[0].start; - } else if (dev && strncmp(dev_name(dev), "ct:", 3) == 0) { - site = VEXPRESS_SITE_MASTER; - } + if (readl(vexpress_sysreg_base() + SYS_MISC) & SYS_MISC_MASTERSITE) + return VEXPRESS_SITE_DB2; - if (site == VEXPRESS_SITE_MASTER) - site = vexpress_master_site; - - return site; + return VEXPRESS_SITE_DB1; } - -struct vexpress_sysreg_config_func { - u32 template; - u32 device; -}; - -static struct vexpress_config_bridge *vexpress_sysreg_config_bridge; -static struct timer_list vexpress_sysreg_config_timer; -static u32 *vexpress_sysreg_config_data; -static int vexpress_sysreg_config_tries; - -static void *vexpress_sysreg_config_func_get(struct device *dev, - struct device_node *node) +void vexpress_flags_set(u32 data) { - struct vexpress_sysreg_config_func *config_func; - u32 site = 0; - u32 position = 0; - u32 dcc = 0; - u32 func_device[2]; - int err = -EFAULT; - - if (node) { - of_node_get(node); - vexpress_sysreg_find_prop(node, "arm,vexpress,site", &site); - vexpress_sysreg_find_prop(node, "arm,vexpress,position", - &position); - vexpress_sysreg_find_prop(node, "arm,vexpress,dcc", &dcc); - err = of_property_read_u32_array(node, - "arm,vexpress-sysreg,func", func_device, - ARRAY_SIZE(func_device)); - of_node_put(node); - } else if (dev && dev->bus == &platform_bus_type) { - struct platform_device *pdev = to_platform_device(dev); - - if (pdev->num_resources == 1 && - pdev->resource[0].flags == IORESOURCE_BUS) { - site = pdev->resource[0].start; - func_device[0] = pdev->resource[0].end; - func_device[1] = pdev->id; - err = 0; - } - } - if (err) - return NULL; - - config_func = kzalloc(sizeof(*config_func), GFP_KERNEL); - if (!config_func) - return NULL; - - config_func->template = SYS_CFGCTRL_DCC(dcc); - config_func->template |= SYS_CFGCTRL_FUNC(func_device[0]); - config_func->template |= SYS_CFGCTRL_SITE(site == VEXPRESS_SITE_MASTER ? - vexpress_master_site : site); - config_func->template |= SYS_CFGCTRL_POSITION(position); - config_func->device |= func_device[1]; - - dev_dbg(vexpress_sysreg_dev, "func 0x%p = 0x%x, %d\n", config_func, - config_func->template, config_func->device); - - return config_func; + writel(~0, vexpress_sysreg_base() + SYS_FLAGSCLR); + writel(data, vexpress_sysreg_base() + SYS_FLAGSSET); } -static void vexpress_sysreg_config_func_put(void *func) +unsigned int vexpress_get_mci_cardin(struct device *dev) { - kfree(func); + return readl(vexpress_sysreg_base() + SYS_MCI) & SYS_MCI_CARDIN; } -static int vexpress_sysreg_config_func_exec(void *func, int offset, - bool write, u32 *data) +u32 vexpress_get_procid(int site) { - int status; - struct vexpress_sysreg_config_func *config_func = func; - u32 command; - - if (WARN_ON(!vexpress_sysreg_base)) - return -ENOENT; - - command = readl(vexpress_sysreg_base + SYS_CFGCTRL); - if (WARN_ON(command & SYS_CFGCTRL_START)) - return -EBUSY; - - command = SYS_CFGCTRL_START; - command |= write ? SYS_CFGCTRL_WRITE : 0; - command |= config_func->template; - command |= SYS_CFGCTRL_DEVICE(config_func->device + offset); - - /* Use a canary for reads */ - if (!write) - *data = 0xdeadbeef; - - dev_dbg(vexpress_sysreg_dev, "command %x, data %x\n", - command, *data); - writel(*data, vexpress_sysreg_base + SYS_CFGDATA); - writel(0, vexpress_sysreg_base + SYS_CFGSTAT); - writel(command, vexpress_sysreg_base + SYS_CFGCTRL); - mb(); - - if (vexpress_sysreg_dev) { - /* Schedule completion check */ - if (!write) - vexpress_sysreg_config_data = data; - vexpress_sysreg_config_tries = 100; - mod_timer(&vexpress_sysreg_config_timer, - jiffies + usecs_to_jiffies(100)); - status = VEXPRESS_CONFIG_STATUS_WAIT; - } else { - /* Early execution, no timer available, have to spin */ - u32 cfgstat; - - do { - cpu_relax(); - cfgstat = readl(vexpress_sysreg_base + SYS_CFGSTAT); - } while (!cfgstat); - - if (!write && (cfgstat & SYS_CFGSTAT_COMPLETE)) - *data = readl(vexpress_sysreg_base + SYS_CFGDATA); - status = VEXPRESS_CONFIG_STATUS_DONE; - - if (cfgstat & SYS_CFGSTAT_ERR) - status = -EINVAL; - } + if (site == VEXPRESS_SITE_MASTER) + site = vexpress_sysreg_get_master(); - return status; + return readl(vexpress_sysreg_base() + (site == VEXPRESS_SITE_DB1 ? + SYS_PROCID0 : SYS_PROCID1)); } -struct vexpress_config_bridge_info vexpress_sysreg_config_bridge_info = { - .name = "vexpress-sysreg", - .func_get = vexpress_sysreg_config_func_get, - .func_put = vexpress_sysreg_config_func_put, - .func_exec = vexpress_sysreg_config_func_exec, -}; - -static void vexpress_sysreg_config_complete(unsigned long data) +void __iomem *vexpress_get_24mhz_clock_base(void) { - int status = VEXPRESS_CONFIG_STATUS_DONE; - u32 cfgstat = readl(vexpress_sysreg_base + SYS_CFGSTAT); - - if (cfgstat & SYS_CFGSTAT_ERR) - status = -EINVAL; - if (!vexpress_sysreg_config_tries--) - status = -ETIMEDOUT; - - if (status < 0) { - dev_err(vexpress_sysreg_dev, "error %d\n", status); - } else if (!(cfgstat & SYS_CFGSTAT_COMPLETE)) { - mod_timer(&vexpress_sysreg_config_timer, - jiffies + usecs_to_jiffies(50)); - return; - } - - if (vexpress_sysreg_config_data) { - *vexpress_sysreg_config_data = readl(vexpress_sysreg_base + - SYS_CFGDATA); - dev_dbg(vexpress_sysreg_dev, "read data %x\n", - *vexpress_sysreg_config_data); - vexpress_sysreg_config_data = NULL; - } - - vexpress_config_complete(vexpress_sysreg_config_bridge, status); + return vexpress_sysreg_base() + SYS_24MHZ; } -void vexpress_sysreg_setup(struct device_node *node) -{ - if (WARN_ON(!vexpress_sysreg_base)) - return; - - if (readl(vexpress_sysreg_base + SYS_MISC) & SYS_MISC_MASTERSITE) - vexpress_master_site = VEXPRESS_SITE_DB2; - else - vexpress_master_site = VEXPRESS_SITE_DB1; - - vexpress_sysreg_config_bridge = vexpress_config_bridge_register( - node, &vexpress_sysreg_config_bridge_info); - WARN_ON(!vexpress_sysreg_config_bridge); -} - void __init vexpress_sysreg_early_init(void __iomem *base) { - vexpress_sysreg_base = base; - vexpress_sysreg_setup(NULL); -} - -void __init vexpress_sysreg_of_early_init(void) -{ - struct device_node *node; - - if (vexpress_sysreg_base) - return; + __vexpress_sysreg_base = base; - node = of_find_compatible_node(NULL, NULL, "arm,vexpress-sysreg"); - if (node) { - vexpress_sysreg_base = of_iomap(node, 0); - vexpress_sysreg_setup(node); - } + vexpress_config_set_master(vexpress_sysreg_get_master()); } -#ifdef CONFIG_GPIOLIB - -#define VEXPRESS_SYSREG_GPIO(_name, _reg, _value) \ - [VEXPRESS_GPIO_##_name] = { \ - .reg = _reg, \ - .value = _reg##_##_value, \ - } +/* The sysreg block is just a random collection of various functions... */ -static struct vexpress_sysreg_gpio { - unsigned long reg; - u32 value; -} vexpress_sysreg_gpios[] = { - VEXPRESS_SYSREG_GPIO(MMC_CARDIN, SYS_MCI, CARDIN), - VEXPRESS_SYSREG_GPIO(MMC_WPROT, SYS_MCI, WPROT), - VEXPRESS_SYSREG_GPIO(FLASH_WPn, SYS_FLASH, WPn), - VEXPRESS_SYSREG_GPIO(LED0, SYS_LED, LED(0)), - VEXPRESS_SYSREG_GPIO(LED1, SYS_LED, LED(1)), - VEXPRESS_SYSREG_GPIO(LED2, SYS_LED, LED(2)), - VEXPRESS_SYSREG_GPIO(LED3, SYS_LED, LED(3)), - VEXPRESS_SYSREG_GPIO(LED4, SYS_LED, LED(4)), - VEXPRESS_SYSREG_GPIO(LED5, SYS_LED, LED(5)), - VEXPRESS_SYSREG_GPIO(LED6, SYS_LED, LED(6)), - VEXPRESS_SYSREG_GPIO(LED7, SYS_LED, LED(7)), +static struct syscon_platform_data vexpress_sysreg_sys_id_pdata = { + .label = "sys_id", }; -static int vexpress_sysreg_gpio_direction_input(struct gpio_chip *chip, - unsigned offset) -{ - return 0; -} - -static int vexpress_sysreg_gpio_get(struct gpio_chip *chip, - unsigned offset) -{ - struct vexpress_sysreg_gpio *gpio = &vexpress_sysreg_gpios[offset]; - u32 reg_value = readl(vexpress_sysreg_base + gpio->reg); - - return !!(reg_value & gpio->value); -} - -static void vexpress_sysreg_gpio_set(struct gpio_chip *chip, - unsigned offset, int value) -{ - struct vexpress_sysreg_gpio *gpio = &vexpress_sysreg_gpios[offset]; - u32 reg_value = readl(vexpress_sysreg_base + gpio->reg); - - if (value) - reg_value |= gpio->value; - else - reg_value &= ~gpio->value; - - writel(reg_value, vexpress_sysreg_base + gpio->reg); -} - -static int vexpress_sysreg_gpio_direction_output(struct gpio_chip *chip, - unsigned offset, int value) -{ - vexpress_sysreg_gpio_set(chip, offset, value); - - return 0; -} - -static struct gpio_chip vexpress_sysreg_gpio_chip = { - .label = "vexpress-sysreg", - .direction_input = vexpress_sysreg_gpio_direction_input, - .direction_output = vexpress_sysreg_gpio_direction_output, - .get = vexpress_sysreg_gpio_get, - .set = vexpress_sysreg_gpio_set, - .ngpio = ARRAY_SIZE(vexpress_sysreg_gpios), - .base = 0, +static struct bgpio_pdata vexpress_sysreg_sys_led_pdata = { + .label = "sys_led", + .base = -1, + .ngpio = 8, }; - -#define VEXPRESS_SYSREG_GREEN_LED(_name, _default_trigger, _gpio) \ - { \ - .name = "v2m:green:"_name, \ - .default_trigger = _default_trigger, \ - .gpio = VEXPRESS_GPIO_##_gpio, \ - } - -struct gpio_led vexpress_sysreg_leds[] = { - VEXPRESS_SYSREG_GREEN_LED("user1", "heartbeat", LED0), - VEXPRESS_SYSREG_GREEN_LED("user2", "mmc0", LED1), - VEXPRESS_SYSREG_GREEN_LED("user3", "cpu0", LED2), - VEXPRESS_SYSREG_GREEN_LED("user4", "cpu1", LED3), - VEXPRESS_SYSREG_GREEN_LED("user5", "cpu2", LED4), - VEXPRESS_SYSREG_GREEN_LED("user6", "cpu3", LED5), - VEXPRESS_SYSREG_GREEN_LED("user7", "cpu4", LED6), - VEXPRESS_SYSREG_GREEN_LED("user8", "cpu5", LED7), +static struct bgpio_pdata vexpress_sysreg_sys_mci_pdata = { + .label = "sys_mci", + .base = -1, + .ngpio = 2, }; -struct gpio_led_platform_data vexpress_sysreg_leds_pdata = { - .num_leds = ARRAY_SIZE(vexpress_sysreg_leds), - .leds = vexpress_sysreg_leds, +static struct bgpio_pdata vexpress_sysreg_sys_flash_pdata = { + .label = "sys_flash", + .base = -1, + .ngpio = 1, }; -#endif - +static struct syscon_platform_data vexpress_sysreg_sys_misc_pdata = { + .label = "sys_misc", +}; -static ssize_t vexpress_sysreg_sys_id_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - return sprintf(buf, "0x%08x\n", readl(vexpress_sysreg_base + SYS_ID)); -} +static struct syscon_platform_data vexpress_sysreg_sys_procid_pdata = { + .label = "sys_procid", +}; -DEVICE_ATTR(sys_id, S_IRUGO, vexpress_sysreg_sys_id_show, NULL); +static struct mfd_cell vexpress_sysreg_cells[] = { + { + .name = "syscon", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM(SYS_ID, 0x4), + }, + .platform_data = &vexpress_sysreg_sys_id_pdata, + .pdata_size = sizeof(vexpress_sysreg_sys_id_pdata), + }, { + .name = "basic-mmio-gpio", + .of_compatible = "arm,vexpress-sysreg,sys_led", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM_NAMED(SYS_LED, 0x4, "dat"), + }, + .platform_data = &vexpress_sysreg_sys_led_pdata, + .pdata_size = sizeof(vexpress_sysreg_sys_led_pdata), + }, { + .name = "basic-mmio-gpio", + .of_compatible = "arm,vexpress-sysreg,sys_mci", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM_NAMED(SYS_MCI, 0x4, "dat"), + }, + .platform_data = &vexpress_sysreg_sys_mci_pdata, + .pdata_size = sizeof(vexpress_sysreg_sys_mci_pdata), + }, { + .name = "basic-mmio-gpio", + .of_compatible = "arm,vexpress-sysreg,sys_flash", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM_NAMED(SYS_FLASH, 0x4, "dat"), + }, + .platform_data = &vexpress_sysreg_sys_flash_pdata, + .pdata_size = sizeof(vexpress_sysreg_sys_flash_pdata), + }, { + .name = "syscon", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM(SYS_MISC, 0x4), + }, + .platform_data = &vexpress_sysreg_sys_misc_pdata, + .pdata_size = sizeof(vexpress_sysreg_sys_misc_pdata), + }, { + .name = "syscon", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM(SYS_PROCID0, 0x8), + }, + .platform_data = &vexpress_sysreg_sys_procid_pdata, + .pdata_size = sizeof(vexpress_sysreg_sys_procid_pdata), + }, { + .name = "vexpress-syscfg", + .num_resources = 1, + .resources = (struct resource []) { + DEFINE_RES_MEM(SYS_CFGDATA, 0xc), + }, + } +}; static int vexpress_sysreg_probe(struct platform_device *pdev) { - int err; - struct resource *res = platform_get_resource(pdev, - IORESOURCE_MEM, 0); - - if (!devm_request_mem_region(&pdev->dev, res->start, - resource_size(res), pdev->name)) { - dev_err(&pdev->dev, "Failed to request memory region!\n"); - return -EBUSY; - } + struct resource *mem; + void __iomem *base; + struct bgpio_chip *mmc_gpio_chip; + u32 dt_hbi; - if (!vexpress_sysreg_base) { - vexpress_sysreg_base = devm_ioremap(&pdev->dev, res->start, - resource_size(res)); - vexpress_sysreg_setup(pdev->dev.of_node); - } + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!mem) + return -EINVAL; - if (!vexpress_sysreg_base) { - dev_err(&pdev->dev, "Failed to obtain base address!\n"); - return -EFAULT; - } + base = devm_ioremap(&pdev->dev, mem->start, resource_size(mem)); + if (!base) + return -ENOMEM; - setup_timer(&vexpress_sysreg_config_timer, - vexpress_sysreg_config_complete, 0); + vexpress_config_set_master(vexpress_sysreg_get_master()); - vexpress_sysreg_dev = &pdev->dev; + /* Confirm board type against DT property, if available */ + if (of_property_read_u32(of_allnodes, "arm,hbi", &dt_hbi) == 0) { + u32 id = vexpress_get_procid(VEXPRESS_SITE_MASTER); + u32 hbi = (id >> SYS_PROCIDx_HBI_SHIFT) & SYS_HBI_MASK; -#ifdef CONFIG_GPIOLIB - vexpress_sysreg_gpio_chip.dev = &pdev->dev; - err = gpiochip_add(&vexpress_sysreg_gpio_chip); - if (err) { - vexpress_config_bridge_unregister( - vexpress_sysreg_config_bridge); - dev_err(&pdev->dev, "Failed to register GPIO chip! (%d)\n", - err); - return err; + if (WARN_ON(dt_hbi != hbi)) + dev_warn(&pdev->dev, "DT HBI (%x) is not matching hardware (%x)!\n", + dt_hbi, hbi); } - platform_device_register_data(vexpress_sysreg_dev, "leds-gpio", - PLATFORM_DEVID_AUTO, &vexpress_sysreg_leds_pdata, - sizeof(vexpress_sysreg_leds_pdata)); -#endif - - device_create_file(vexpress_sysreg_dev, &dev_attr_sys_id); - - return 0; + /* + * Duplicated SYS_MCI pseudo-GPIO controller for compatibility with + * older trees using sysreg node for MMC control lines. + */ + mmc_gpio_chip = devm_kzalloc(&pdev->dev, sizeof(*mmc_gpio_chip), + GFP_KERNEL); + if (!mmc_gpio_chip) + return -ENOMEM; + bgpio_init(mmc_gpio_chip, &pdev->dev, 0x4, base + SYS_MCI, + NULL, NULL, NULL, NULL, 0); + mmc_gpio_chip->gc.ngpio = 2; + gpiochip_add(&mmc_gpio_chip->gc); + + return mfd_add_devices(&pdev->dev, PLATFORM_DEVID_AUTO, + vexpress_sysreg_cells, + ARRAY_SIZE(vexpress_sysreg_cells), mem, 0, NULL); } static const struct of_device_id vexpress_sysreg_match[] = { @@ -522,7 +265,12 @@ static struct platform_driver vexpress_sysreg_driver = { static int __init vexpress_sysreg_init(void) { - vexpress_sysreg_of_early_init(); + struct device_node *node; + + /* Need the sysreg early, before any other device... */ + for_each_matching_node(node, vexpress_sysreg_match) + of_platform_device_create(node, NULL, NULL); + return platform_driver_register(&vexpress_sysreg_driver); } core_initcall(vexpress_sysreg_init); diff --git a/drivers/mfd/wm5102-tables.c b/drivers/mfd/wm5102-tables.c index 070f8cfbbd7a..c8a993bd17ae 100644 --- a/drivers/mfd/wm5102-tables.c +++ b/drivers/mfd/wm5102-tables.c @@ -333,7 +333,7 @@ static const struct reg_default wm5102_reg_default[] = { { 0x000001AA, 0x0004 }, /* R426 - FLL2 GPIO Clock */ { 0x00000200, 0x0006 }, /* R512 - Mic Charge Pump 1 */ { 0x00000210, 0x00D4 }, /* R528 - LDO1 Control 1 */ - { 0x00000212, 0x0001 }, /* R530 - LDO1 Control 2 */ + { 0x00000212, 0x0000 }, /* R530 - LDO1 Control 2 */ { 0x00000213, 0x0344 }, /* R531 - LDO2 Control 1 */ { 0x00000218, 0x01A6 }, /* R536 - Mic Bias Ctrl 1 */ { 0x00000219, 0x01A6 }, /* R537 - Mic Bias Ctrl 2 */ @@ -1037,6 +1037,8 @@ static bool wm5102_readable_register(struct device *dev, unsigned int reg) case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_4: case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_5: case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_6: + case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_7: + case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_8: case ARIZONA_COMFORT_NOISE_GENERATOR: case ARIZONA_HAPTICS_CONTROL_1: case ARIZONA_HAPTICS_CONTROL_2: diff --git a/drivers/mfd/wm5110-tables.c b/drivers/mfd/wm5110-tables.c index 1942b6f231da..41a7f6fb7802 100644 --- a/drivers/mfd/wm5110-tables.c +++ b/drivers/mfd/wm5110-tables.c @@ -468,10 +468,12 @@ static const struct reg_default wm5110_reg_default[] = { { 0x00000062, 0x01FF }, /* R98 - Sample Rate Sequence Select 2 */ { 0x00000063, 0x01FF }, /* R99 - Sample Rate Sequence Select 3 */ { 0x00000064, 0x01FF }, /* R100 - Sample Rate Sequence Select 4 */ - { 0x00000068, 0x01FF }, /* R104 - Always On Triggers Sequence Select 1 */ - { 0x00000069, 0x01FF }, /* R105 - Always On Triggers Sequence Select 2 */ - { 0x0000006A, 0x01FF }, /* R106 - Always On Triggers Sequence Select 3 */ - { 0x0000006B, 0x01FF }, /* R107 - Always On Triggers Sequence Select 4 */ + { 0x00000066, 0x01FF }, /* R102 - Always On Triggers Sequence Select 1 */ + { 0x00000067, 0x01FF }, /* R103 - Always On Triggers Sequence Select 2 */ + { 0x00000068, 0x01FF }, /* R104 - Always On Triggers Sequence Select 3 */ + { 0x00000069, 0x01FF }, /* R105 - Always On Triggers Sequence Select 4 */ + { 0x0000006A, 0x01FF }, /* R106 - Always On Triggers Sequence Select 5 */ + { 0x0000006B, 0x01FF }, /* R107 - Always On Triggers Sequence Select 6 */ { 0x00000070, 0x0000 }, /* R112 - Comfort Noise Generator */ { 0x00000090, 0x0000 }, /* R144 - Haptics Control 1 */ { 0x00000091, 0x7FFF }, /* R145 - Haptics Control 2 */ @@ -549,6 +551,7 @@ static const struct reg_default wm5110_reg_default[] = { { 0x000002A8, 0x1422 }, /* R680 - Mic Detect Level 3 */ { 0x000002A9, 0x300A }, /* R681 - Mic Detect Level 4 */ { 0x000002C3, 0x0000 }, /* R707 - Mic noise mix control 1 */ + { 0x000002CB, 0x0000 }, /* R715 - Isolation control */ { 0x000002D3, 0x0000 }, /* R723 - Jack detect analogue */ { 0x00000300, 0x0000 }, /* R768 - Input Enables */ { 0x00000308, 0x0000 }, /* R776 - Input Rate */ @@ -1498,6 +1501,8 @@ static bool wm5110_readable_register(struct device *dev, unsigned int reg) case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_2: case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_3: case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_4: + case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_5: + case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_6: case ARIZONA_COMFORT_NOISE_GENERATOR: case ARIZONA_HAPTICS_CONTROL_1: case ARIZONA_HAPTICS_CONTROL_2: @@ -1580,6 +1585,7 @@ static bool wm5110_readable_register(struct device *dev, unsigned int reg) case ARIZONA_MIC_DETECT_LEVEL_3: case ARIZONA_MIC_DETECT_LEVEL_4: case ARIZONA_MIC_NOISE_MIX_CONTROL_1: + case ARIZONA_ISOLATION_CONTROL: case ARIZONA_JACK_DETECT_ANALOGUE: case ARIZONA_INPUT_ENABLES: case ARIZONA_INPUT_ENABLES_STATUS: diff --git a/drivers/mfd/wm8400-core.c b/drivers/mfd/wm8400-core.c index e5eae751aa1b..c6fb5d16ca09 100644 --- a/drivers/mfd/wm8400-core.c +++ b/drivers/mfd/wm8400-core.c @@ -64,7 +64,7 @@ EXPORT_SYMBOL_GPL(wm8400_block_read); static int wm8400_register_codec(struct wm8400 *wm8400) { - struct mfd_cell cell = { + const struct mfd_cell cell = { .name = "wm8400-codec", .platform_data = wm8400, .pdata_size = sizeof(*wm8400), diff --git a/drivers/mfd/wm8997-tables.c b/drivers/mfd/wm8997-tables.c index 5aa807687777..c7a81da64ee1 100644 --- a/drivers/mfd/wm8997-tables.c +++ b/drivers/mfd/wm8997-tables.c @@ -174,10 +174,10 @@ static const struct reg_default wm8997_reg_default[] = { { 0x00000062, 0x01FF }, /* R98 - Sample Rate Sequence Select 2 */ { 0x00000063, 0x01FF }, /* R99 - Sample Rate Sequence Select 3 */ { 0x00000064, 0x01FF }, /* R100 - Sample Rate Sequence Select 4 */ - { 0x00000068, 0x01FF }, /* R104 - Always On Triggers Sequence Select 1 */ - { 0x00000069, 0x01FF }, /* R105 - Always On Triggers Sequence Select 2 */ - { 0x0000006A, 0x01FF }, /* R106 - Always On Triggers Sequence Select 3 */ - { 0x0000006B, 0x01FF }, /* R107 - Always On Triggers Sequence Select 4 */ + { 0x00000068, 0x01FF }, /* R104 - Always On Triggers Sequence Select 3 */ + { 0x00000069, 0x01FF }, /* R105 - Always On Triggers Sequence Select 4 */ + { 0x0000006A, 0x01FF }, /* R106 - Always On Triggers Sequence Select 5 */ + { 0x0000006B, 0x01FF }, /* R107 - Always On Triggers Sequence Select 6 */ { 0x00000070, 0x0000 }, /* R112 - Comfort Noise Generator */ { 0x00000090, 0x0000 }, /* R144 - Haptics Control 1 */ { 0x00000091, 0x7FFF }, /* R145 - Haptics Control 2 */ @@ -814,10 +814,10 @@ static bool wm8997_readable_register(struct device *dev, unsigned int reg) case ARIZONA_SAMPLE_RATE_SEQUENCE_SELECT_2: case ARIZONA_SAMPLE_RATE_SEQUENCE_SELECT_3: case ARIZONA_SAMPLE_RATE_SEQUENCE_SELECT_4: - case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_1: - case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_2: case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_3: case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_4: + case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_5: + case ARIZONA_ALWAYS_ON_TRIGGERS_SEQUENCE_SELECT_6: case ARIZONA_COMFORT_NOISE_GENERATOR: case ARIZONA_HAPTICS_CONTROL_1: case ARIZONA_HAPTICS_CONTROL_2: @@ -846,6 +846,7 @@ static bool wm8997_readable_register(struct device *dev, unsigned int reg) case ARIZONA_RATE_ESTIMATOR_3: case ARIZONA_RATE_ESTIMATOR_4: case ARIZONA_RATE_ESTIMATOR_5: + case ARIZONA_DYNAMIC_FREQUENCY_SCALING_1: case ARIZONA_FLL1_CONTROL_1: case ARIZONA_FLL1_CONTROL_2: case ARIZONA_FLL1_CONTROL_3: @@ -880,6 +881,7 @@ static bool wm8997_readable_register(struct device *dev, unsigned int reg) case ARIZONA_FLL2_GPIO_CLOCK: case ARIZONA_MIC_CHARGE_PUMP_1: case ARIZONA_LDO1_CONTROL_1: + case ARIZONA_LDO1_CONTROL_2: case ARIZONA_LDO2_CONTROL_1: case ARIZONA_MIC_BIAS_CTRL_1: case ARIZONA_MIC_BIAS_CTRL_2: |