diff options
Diffstat (limited to 'drivers/block/umem.h')
| -rw-r--r-- | drivers/block/umem.h | 132 |
1 files changed, 0 insertions, 132 deletions
diff --git a/drivers/block/umem.h b/drivers/block/umem.h deleted file mode 100644 index 58384978ff05..000000000000 --- a/drivers/block/umem.h +++ /dev/null @@ -1,132 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-only */ - -/* - * This file contains defines for the - * Micro Memory MM5415 - * family PCI Memory Module with Battery Backup. - * - * Copyright Micro Memory INC 2001. All rights reserved. - */ - -#ifndef _DRIVERS_BLOCK_MM_H -#define _DRIVERS_BLOCK_MM_H - - -#define IRQ_TIMEOUT (1 * HZ) - -/* CSR register definition */ -#define MEMCTRLSTATUS_MAGIC 0x00 -#define MM_MAGIC_VALUE (unsigned char)0x59 - -#define MEMCTRLSTATUS_BATTERY 0x04 -#define BATTERY_1_DISABLED 0x01 -#define BATTERY_1_FAILURE 0x02 -#define BATTERY_2_DISABLED 0x04 -#define BATTERY_2_FAILURE 0x08 - -#define MEMCTRLSTATUS_MEMORY 0x07 -#define MEM_128_MB 0xfe -#define MEM_256_MB 0xfc -#define MEM_512_MB 0xf8 -#define MEM_1_GB 0xf0 -#define MEM_2_GB 0xe0 - -#define MEMCTRLCMD_LEDCTRL 0x08 -#define LED_REMOVE 2 -#define LED_FAULT 4 -#define LED_POWER 6 -#define LED_FLIP 255 -#define LED_OFF 0x00 -#define LED_ON 0x01 -#define LED_FLASH_3_5 0x02 -#define LED_FLASH_7_0 0x03 -#define LED_POWER_ON 0x00 -#define LED_POWER_OFF 0x01 -#define USER_BIT1 0x01 -#define USER_BIT2 0x02 - -#define MEMORY_INITIALIZED USER_BIT1 - -#define MEMCTRLCMD_ERRCTRL 0x0C -#define EDC_NONE_DEFAULT 0x00 -#define EDC_NONE 0x01 -#define EDC_STORE_READ 0x02 -#define EDC_STORE_CORRECT 0x03 - -#define MEMCTRLCMD_ERRCNT 0x0D -#define MEMCTRLCMD_ERRSTATUS 0x0E - -#define ERROR_DATA_LOG 0x20 -#define ERROR_ADDR_LOG 0x28 -#define ERROR_COUNT 0x3D -#define ERROR_SYNDROME 0x3E -#define ERROR_CHECK 0x3F - -#define DMA_PCI_ADDR 0x40 -#define DMA_LOCAL_ADDR 0x48 -#define DMA_TRANSFER_SIZE 0x50 -#define DMA_DESCRIPTOR_ADDR 0x58 -#define DMA_SEMAPHORE_ADDR 0x60 -#define DMA_STATUS_CTRL 0x68 -#define DMASCR_GO 0x00001 -#define DMASCR_TRANSFER_READ 0x00002 -#define DMASCR_CHAIN_EN 0x00004 -#define DMASCR_SEM_EN 0x00010 -#define DMASCR_DMA_COMP_EN 0x00020 -#define DMASCR_CHAIN_COMP_EN 0x00040 -#define DMASCR_ERR_INT_EN 0x00080 -#define DMASCR_PARITY_INT_EN 0x00100 -#define DMASCR_ANY_ERR 0x00800 -#define DMASCR_MBE_ERR 0x01000 -#define DMASCR_PARITY_ERR_REP 0x02000 -#define DMASCR_PARITY_ERR_DET 0x04000 -#define DMASCR_SYSTEM_ERR_SIG 0x08000 -#define DMASCR_TARGET_ABT 0x10000 -#define DMASCR_MASTER_ABT 0x20000 -#define DMASCR_DMA_COMPLETE 0x40000 -#define DMASCR_CHAIN_COMPLETE 0x80000 - -/* -3.SOME PCs HAVE HOST BRIDGES WHICH APPARENTLY DO NOT CORRECTLY HANDLE -READ-LINE (0xE) OR READ-MULTIPLE (0xC) PCI COMMAND CODES DURING DMA -TRANSFERS. IN OTHER SYSTEMS THESE COMMAND CODES WILL CAUSE THE HOST BRIDGE -TO ALLOW LONGER BURSTS DURING DMA READ OPERATIONS. THE UPPER FOUR BITS -(31..28) OF THE DMA CSR HAVE BEEN MADE PROGRAMMABLE, SO THAT EITHER A 0x6, -AN 0xE OR A 0xC CAN BE WRITTEN TO THEM TO SET THE COMMAND CODE USED DURING -DMA READ OPERATIONS. -*/ -#define DMASCR_READ 0x60000000 -#define DMASCR_READLINE 0xE0000000 -#define DMASCR_READMULTI 0xC0000000 - - -#define DMASCR_ERROR_MASK (DMASCR_MASTER_ABT | DMASCR_TARGET_ABT | DMASCR_SYSTEM_ERR_SIG | DMASCR_PARITY_ERR_DET | DMASCR_MBE_ERR | DMASCR_ANY_ERR) -#define DMASCR_HARD_ERROR (DMASCR_MASTER_ABT | DMASCR_TARGET_ABT | DMASCR_SYSTEM_ERR_SIG | DMASCR_PARITY_ERR_DET | DMASCR_MBE_ERR) - -#define WINDOWMAP_WINNUM 0x7B - -#define DMA_READ_FROM_HOST 0 -#define DMA_WRITE_TO_HOST 1 - -struct mm_dma_desc { - __le64 pci_addr; - __le64 local_addr; - __le32 transfer_size; - u32 zero1; - __le64 next_desc_addr; - __le64 sem_addr; - __le32 control_bits; - u32 zero2; - - dma_addr_t data_dma_handle; - - /* Copy of the bits */ - __le64 sem_control_bits; -} __attribute__((aligned(8))); - -/* bits for card->flags */ -#define UM_FLAG_DMA_IN_REGS 1 -#define UM_FLAG_NO_BYTE_STATUS 2 -#define UM_FLAG_NO_BATTREG 4 -#define UM_FLAG_NO_BATT 8 -#endif |