diff options
Diffstat (limited to 'drivers/ata/pata_pdc202xx_old.c')
-rw-r--r-- | drivers/ata/pata_pdc202xx_old.c | 423 |
1 files changed, 423 insertions, 0 deletions
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c new file mode 100644 index 000000000000..48f43432764e --- /dev/null +++ b/drivers/ata/pata_pdc202xx_old.c @@ -0,0 +1,423 @@ +/* + * pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based in part on linux/drivers/ide/pci/pdc202xx_old.c + * + * First cut with LBA48/ATAPI + * + * TODO: + * Channel interlock/reset on both required ? + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_pdc202xx_old" +#define DRV_VERSION "0.2.1" + +/** + * pdc2024x_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int pdc2024x_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + +static void pdc2024x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, pdc2024x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + + +static int pdc2026x_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 cis; + + pci_read_config_word(pdev, 0x50, &cis); + if (cis & (1 << (10 + ap->port_no))) + ap->cbl = ATA_CBL_PATA80; + else + ap->cbl = ATA_CBL_PATA40; + + return ata_std_prereset(ap); +} + +static void pdc2026x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, pdc2026x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * pdc_configure_piomode - set chip PIO timing + * @ap: ATA interface + * @adev: ATA device + * @pio: PIO mode + * + * Called to do the PIO mode setup. Our timing registers are shared + * so a configure_dmamode call will undo any work we do here and vice + * versa + */ + +static void pdc_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x60 + 4 * ap->port_no + 2 * adev->devno; + static u16 pio_timing[5] = { + 0x0913, 0x050C , 0x0308, 0x0206, 0x0104 + }; + u8 r_ap, r_bp; + + pci_read_config_byte(pdev, port, &r_ap); + pci_read_config_byte(pdev, port + 1, &r_bp); + r_ap &= ~0x3F; /* Preserve ERRDY_EN, SYNC_IN */ + r_bp &= ~0x07; + r_ap |= (pio_timing[pio] >> 8); + r_bp |= (pio_timing[pio] & 0xFF); + + if (ata_pio_need_iordy(adev)) + r_ap |= 0x20; /* IORDY enable */ + if (adev->class == ATA_DEV_ATA) + r_ap |= 0x10; /* FIFO enable */ + pci_write_config_byte(pdev, port, r_ap); + pci_write_config_byte(pdev, port + 1, r_bp); +} + +/** + * pdc_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. Our timing registers are shared + * but we want to set the PIO timing by default. + */ + +static void pdc_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + pdc_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); +} + +/** + * pdc_configure_dmamode - set DMA mode in chip + * @ap: ATA interface + * @adev: ATA device + * + * Load DMA cycle times into the chip ready for a DMA transfer + * to occur. + */ + +static void pdc_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x60 + 4 * ap->port_no + 2 * adev->devno; + static u8 udma_timing[6][2] = { + { 0x60, 0x03 }, /* 33 Mhz Clock */ + { 0x40, 0x02 }, + { 0x20, 0x01 }, + { 0x40, 0x02 }, /* 66 Mhz Clock */ + { 0x20, 0x01 }, + { 0x20, 0x01 } + }; + u8 r_bp, r_cp; + + pci_read_config_byte(pdev, port + 1, &r_bp); + pci_read_config_byte(pdev, port + 2, &r_cp); + + r_bp &= ~0xF0; + r_cp &= ~0x0F; + + if (adev->dma_mode >= XFER_UDMA_0) { + int speed = adev->dma_mode - XFER_UDMA_0; + r_bp |= udma_timing[speed][0]; + r_cp |= udma_timing[speed][1]; + + } else { + int speed = adev->dma_mode - XFER_MW_DMA_0; + r_bp |= 0x60; + r_cp |= (5 - speed); + } + pci_write_config_byte(pdev, port + 1, r_bp); + pci_write_config_byte(pdev, port + 2, r_cp); + +} + +/** + * pdc2026x_bmdma_start - DMA engine begin + * @qc: ATA command + * + * In UDMA3 or higher we have to clock switch for the duration of the + * DMA transfer sequence. + */ + +static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_taskfile *tf = &qc->tf; + int sel66 = ap->port_no ? 0x08: 0x02; + + unsigned long master = ap->host->ports[0]->ioaddr.bmdma_addr; + unsigned long clock = master + 0x11; + unsigned long atapi_reg = master + 0x20 + (4 * ap->port_no); + + u32 len; + + /* Check we keep host level locking here */ + if (adev->dma_mode >= XFER_UDMA_2) + outb(inb(clock) | sel66, clock); + else + outb(inb(clock) & ~sel66, clock); + + /* The DMA clocks may have been trashed by a reset. FIXME: make conditional + and move to qc_issue ? */ + pdc_set_dmamode(ap, qc->dev); + + /* Cases the state machine will not complete correctly without help */ + if ((tf->flags & ATA_TFLAG_LBA48) || tf->protocol == ATA_PROT_ATAPI_DMA) + { + if (tf->flags & ATA_TFLAG_LBA48) + len = qc->nsect * 512; + else + len = qc->nbytes; + + if (tf->flags & ATA_TFLAG_WRITE) + len |= 0x06000000; + else + len |= 0x05000000; + + outl(len, atapi_reg); + } + + /* Activate DMA */ + ata_bmdma_start(qc); +} + +/** + * pdc2026x_bmdma_end - DMA engine stop + * @qc: ATA command + * + * After a DMA completes we need to put the clock back to 33MHz for + * PIO timings. + */ + +static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_taskfile *tf = &qc->tf; + + int sel66 = ap->port_no ? 0x08: 0x02; + /* The clock bits are in the same register for both channels */ + unsigned long master = ap->host->ports[0]->ioaddr.bmdma_addr; + unsigned long clock = master + 0x11; + unsigned long atapi_reg = master + 0x20 + (4 * ap->port_no); + + /* Cases the state machine will not complete correctly */ + if (tf->protocol == ATA_PROT_ATAPI_DMA || ( tf->flags & ATA_TFLAG_LBA48)) { + outl(0, atapi_reg); + outb(inb(clock) & ~sel66, clock); + } + /* Check we keep host level locking here */ + /* Flip back to 33Mhz for PIO */ + if (adev->dma_mode >= XFER_UDMA_2) + outb(inb(clock) & ~sel66, clock); + + ata_bmdma_stop(qc); +} + +/** + * pdc2026x_dev_config - device setup hook + * @ap: ATA port + * @adev: newly found device + * + * Perform chip specific early setup. We need to lock the transfer + * sizes to 8bit to avoid making the state engine on the 2026x cards + * barf. + */ + +static void pdc2026x_dev_config(struct ata_port *ap, struct ata_device *adev) +{ + adev->max_sectors = 256; +} + +static struct scsi_host_template pdc_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations pdc2024x_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = pdc_set_piomode, + .set_dmamode = pdc_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2024x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations pdc2026x_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = pdc_set_piomode, + .set_dmamode = pdc_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .dev_config = pdc2026x_dev_config, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2026x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = pdc2026x_bmdma_start, + .bmdma_stop = pdc2026x_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info[3] = { + { + .sht = &pdc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA2, + .port_ops = &pdc2024x_port_ops + }, + { + .sht = &pdc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA4, + .port_ops = &pdc2026x_port_ops + }, + { + .sht = &pdc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA5, + .port_ops = &pdc2026x_port_ops + } + + }; + static struct ata_port_info *port_info[2]; + + port_info[0] = port_info[1] = &info[id->driver_data]; + + if (dev->device == PCI_DEVICE_ID_PROMISE_20265) { + struct pci_dev *bridge = dev->bus->self; + /* Don't grab anything behind a Promise I2O RAID */ + if (bridge && bridge->vendor == PCI_VENDOR_ID_INTEL) { + if( bridge->device == PCI_DEVICE_ID_INTEL_I960) + return -ENODEV; + if( bridge->device == PCI_DEVICE_ID_INTEL_I960RM) + return -ENODEV; + } + } + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id pdc[] = { + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2}, + { 0, }, +}; + +static struct pci_driver pdc_pci_driver = { + .name = DRV_NAME, + .id_table = pdc, + .probe = pdc_init_one, + .remove = ata_pci_remove_one +}; + +static int __init pdc_init(void) +{ + return pci_register_driver(&pdc_pci_driver); +} + + +static void __exit pdc_exit(void) +{ + pci_unregister_driver(&pdc_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pdc); +MODULE_VERSION(DRV_VERSION); + +module_init(pdc_init); +module_exit(pdc_exit); |