diff options
Diffstat (limited to 'drivers/ata/pata_hpt3x2n.c')
-rw-r--r-- | drivers/ata/pata_hpt3x2n.c | 597 |
1 files changed, 597 insertions, 0 deletions
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c new file mode 100644 index 000000000000..06c8db079b91 --- /dev/null +++ b/drivers/ata/pata_hpt3x2n.c @@ -0,0 +1,597 @@ +/* + * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers. + * + * This driver is heavily based upon: + * + * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 + * + * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> + * Portions Copyright (C) 2001 Sun Microsystems, Inc. + * Portions Copyright (C) 2003 Red Hat Inc + * + * + * TODO + * 371N + * Work out best PLL policy + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_hpt3x2n" +#define DRV_VERSION "0.3" + +enum { + HPT_PCI_FAST = (1 << 31), + PCI66 = (1 << 1), + USE_DPLL = (1 << 0) +}; + +struct hpt_clock { + u8 xfer_speed; + u32 timing; +}; + +struct hpt_chip { + const char *name; + struct hpt_clock *clocks[3]; +}; + +/* key for bus clock timings + * bit + * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * register access. + * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * register access. + * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. + * during task file register access. + * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA + * xfer. + * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * register access. + * 28 UDMA enable + * 29 DMA enable + * 30 PIO_MST enable. if set, the chip is in bus master mode during + * PIO. + * 31 FIFO enable. + */ + +/* 66MHz DPLL clocks */ + +static struct hpt_clock hpt3x2n_clocks[] = { + { XFER_UDMA_7, 0x1c869c62 }, + { XFER_UDMA_6, 0x1c869c62 }, + { XFER_UDMA_5, 0x1c8a9c62 }, + { XFER_UDMA_4, 0x1c8a9c62 }, + { XFER_UDMA_3, 0x1c8e9c62 }, + { XFER_UDMA_2, 0x1c929c62 }, + { XFER_UDMA_1, 0x1c9a9c62 }, + { XFER_UDMA_0, 0x1c829c62 }, + + { XFER_MW_DMA_2, 0x2c829c62 }, + { XFER_MW_DMA_1, 0x2c829c66 }, + { XFER_MW_DMA_0, 0x2c829d2c }, + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d5e } +}; + +/** + * hpt3x2n_find_mode - reset the hpt3x2n bus + * @ap: ATA port + * @speed: transfer mode + * + * Return the 32bit register programming information for this channel + * that matches the speed provided. For the moment the clocks table + * is hard coded but easy to change. This will be needed if we use + * different DPLLs + */ + +static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed) +{ + struct hpt_clock *clocks = hpt3x2n_clocks; + + while(clocks->xfer_speed) { + if (clocks->xfer_speed == speed) + return clocks->timing; + clocks++; + } + BUG(); + return 0xffffffffU; /* silence compiler warning */ +} + +/** + * hpt3x2n_pre_reset - reset the hpt3x2n bus + * @ap: ATA port to reset + * + * Perform the initial reset handling for the 3x2n series controllers. + * Reset the hardware and state machine, obtain the cable type. + */ + +static int hpt3xn_pre_reset(struct ata_port *ap) +{ + u8 scr2, ata66; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x5B, &scr2); + pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); + /* Cable register now active */ + pci_read_config_byte(pdev, 0x5A, &ata66); + /* Restore state */ + pci_write_config_byte(pdev, 0x5B, scr2); + + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + /* Reset the state machine */ + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); + udelay(100); + + return ata_std_prereset(ap); +} + +/** + * hpt3x2n_error_handler - probe the hpt3x2n bus + * @ap: ATA port to reset + * + * Perform the probe reset handling for the 3x2N + */ + +static void hpt3x2n_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt3x2n_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt3x2n_find_mode(ap, adev->pio_mode); + mode &= ~0x8000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt3x2n_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt3x2n_find_mode(ap, adev->dma_mode); + mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ + mode &= ~0xC0000000; /* Leave config bits alone */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt3x2n_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Clean up after the HPT3x2n and later DMA engine + */ + +static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int mscreg = 0x50 + 2 * ap->port_no; + u8 bwsr_stat, msc_stat; + + pci_read_config_byte(pdev, 0x6A, &bwsr_stat); + pci_read_config_byte(pdev, mscreg, &msc_stat); + if (bwsr_stat & (1 << ap->port_no)) + pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); + ata_bmdma_stop(qc); +} + +/** + * hpt3x2n_set_clock - clock control + * @ap: ATA port + * @source: 0x21 or 0x23 for PLL or PCI sourced clock + * + * Switch the ATA bus clock between the PLL and PCI clock sources + * while correctly isolating the bus and resetting internal logic + * + * We must use the DPLL for + * - writing + * - second channel UDMA7 (SATA ports) or higher + * - 66MHz PCI + * + * or we will underclock the device and get reduced performance. + */ + +static void hpt3x2n_set_clock(struct ata_port *ap, int source) +{ + unsigned long bmdma = ap->ioaddr.bmdma_addr; + + /* Tristate the bus */ + outb(0x80, bmdma+0x73); + outb(0x80, bmdma+0x77); + + /* Switch clock and reset channels */ + outb(source, bmdma+0x7B); + outb(0xC0, bmdma+0x79); + + /* Reset state machines */ + outb(0x37, bmdma+0x70); + outb(0x37, bmdma+0x74); + + /* Complete reset */ + outb(0x00, bmdma+0x79); + + /* Reconnect channels to bus */ + outb(0x00, bmdma+0x73); + outb(0x00, bmdma+0x77); +} + +/* Check if our partner interface is busy */ + +static int hpt3x2n_pair_idle(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + struct ata_port *pair = host->ports[ap->port_no ^ 1]; + + if (pair->hsm_task_state == HSM_ST_IDLE) + return 1; + return 0; +} + +static int hpt3x2n_use_dpll(struct ata_port *ap, int reading) +{ + long flags = (long)ap->host->private_data; + /* See if we should use the DPLL */ + if (reading == 0) + return USE_DPLL; /* Needed for write */ + if (flags & PCI66) + return USE_DPLL; /* Needed at 66Mhz */ + return 0; +} + +static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_taskfile *tf = &qc->tf; + struct ata_port *ap = qc->ap; + int flags = (long)ap->host->private_data; + + if (hpt3x2n_pair_idle(ap)) { + int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE)); + if ((flags & USE_DPLL) != dpll) { + if (dpll == 1) + hpt3x2n_set_clock(ap, 0x21); + else + hpt3x2n_set_clock(ap, 0x23); + } + } + return ata_qc_issue_prot(qc); +} + +static struct scsi_host_template hpt3x2n_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * Configuration for HPT3x2n. + */ + +static struct ata_port_operations hpt3x2n_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt3x2n_set_piomode, + .set_dmamode = hpt3x2n_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt3x2n_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = hpt3x2n_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = hpt3x2n_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * hpt3xn_calibrate_dpll - Calibrate the DPLL loop + * @dev: PCI device + * + * Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this + * succeeds + */ + +static int hpt3xn_calibrate_dpll(struct pci_dev *dev) +{ + u8 reg5b; + u32 reg5c; + int tries; + + for(tries = 0; tries < 0x5000; tries++) { + udelay(50); + pci_read_config_byte(dev, 0x5b, ®5b); + if (reg5b & 0x80) { + /* See if it stays set */ + for(tries = 0; tries < 0x1000; tries ++) { + pci_read_config_byte(dev, 0x5b, ®5b); + /* Failed ? */ + if ((reg5b & 0x80) == 0) + return 0; + } + /* Turn off tuning, we have the DPLL set */ + pci_read_config_dword(dev, 0x5c, ®5c); + pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100); + return 1; + } + } + /* Never went stable */ + return 0; +} + +static int hpt3x2n_pci_clock(struct pci_dev *pdev) +{ + unsigned long freq; + u32 fcnt; + + pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt); + if ((fcnt >> 12) != 0xABCDE) { + printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n"); + return 33; /* Not BIOS set */ + } + fcnt &= 0x1FF; + + freq = (fcnt * 77) / 192; + + /* Clamp to bands */ + if (freq < 40) + return 33; + if (freq < 45) + return 40; + if (freq < 55) + return 50; + return 66; +} + +/** + * hpt3x2n_init_one - Initialise an HPT37X/302 + * @dev: PCI device + * @id: Entry in match table + * + * Initialise an HPT3x2n device. There are some interesting complications + * here. Firstly the chip may report 366 and be one of several variants. + * Secondly all the timings depend on the clock for the chip which we must + * detect and look up + * + * This is the known chip mappings. It may be missing a couple of later + * releases. + * + * Chip version PCI Rev Notes + * HPT372 4 (HPT366) 5 Other driver + * HPT372N 4 (HPT366) 6 UDMA133 + * HPT372 5 (HPT372) 1 Other driver + * HPT372N 5 (HPT372) 2 UDMA133 + * HPT302 6 (HPT302) * Other driver + * HPT302N 6 (HPT302) > 1 UDMA133 + * HPT371 7 (HPT371) * Other driver + * HPT371N 7 (HPT371) > 1 UDMA133 + * HPT374 8 (HPT374) * Other driver + * HPT372N 9 (HPT372N) * UDMA133 + * + * (1) UDMA133 support depends on the bus clock + * + * To pin down HPT371N + */ + +static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + /* HPT372N and friends - UDMA133 */ + static struct ata_port_info info = { + .sht = &hpt3x2n_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &hpt3x2n_port_ops + }; + struct ata_port_info *port_info[2]; + struct ata_port_info *port = &info; + + u8 irqmask; + u32 class_rev; + + unsigned int pci_mhz; + unsigned int f_low, f_high; + int adjust; + + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xFF; + + switch(dev->device) { + case PCI_DEVICE_ID_TTI_HPT366: + if (class_rev < 6) + return -ENODEV; + break; + case PCI_DEVICE_ID_TTI_HPT372: + /* 372N if rev >= 1*/ + if (class_rev == 0) + return -ENODEV; + break; + case PCI_DEVICE_ID_TTI_HPT302: + if (class_rev < 2) + return -ENODEV; + break; + case PCI_DEVICE_ID_TTI_HPT372N: + break; + default: + printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device); + return -ENODEV; + } + + /* Ok so this is a chip we support */ + + pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); + pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); + pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); + + pci_read_config_byte(dev, 0x5A, &irqmask); + irqmask &= ~0x10; + pci_write_config_byte(dev, 0x5a, irqmask); + + /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or + 50 for UDMA100. Right now we always use 66 */ + + pci_mhz = hpt3x2n_pci_clock(dev); + + f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */ + f_high = f_low + 2; /* Tolerance */ + + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100); + /* PLL clock */ + pci_write_config_byte(dev, 0x5B, 0x21); + + /* Unlike the 37x we don't try jiggling the frequency */ + for(adjust = 0; adjust < 8; adjust++) { + if (hpt3xn_calibrate_dpll(dev)) + break; + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); + } + if (adjust == 8) + printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n"); + + /* Set our private data up. We only need a few flags so we use + it directly */ + port->private_data = NULL; + if (pci_mhz > 60) + port->private_data = (void *)PCI66; + + /* Now kick off ATA set up */ + port_info[0] = port_info[1] = port; + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt3x2n[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N), }, + { 0, }, +}; + +static struct pci_driver hpt3x2n_pci_driver = { + .name = DRV_NAME, + .id_table = hpt3x2n, + .probe = hpt3x2n_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt3x2n_init(void) +{ + return pci_register_driver(&hpt3x2n_pci_driver); +} + + +static void __exit hpt3x2n_exit(void) +{ + pci_unregister_driver(&hpt3x2n_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt3x2n); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt3x2n_init); +module_exit(hpt3x2n_exit); |