diff options
Diffstat (limited to 'arch/sparc/include/asm/ecc.h')
| -rw-r--r-- | arch/sparc/include/asm/ecc.h | 122 |
1 files changed, 122 insertions, 0 deletions
diff --git a/arch/sparc/include/asm/ecc.h b/arch/sparc/include/asm/ecc.h new file mode 100644 index 000000000000..ccb84b66fef1 --- /dev/null +++ b/arch/sparc/include/asm/ecc.h @@ -0,0 +1,122 @@ +/* + * ecc.h: Definitions and defines for the external cache/memory + * controller on the sun4m. + * + * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) + */ + +#ifndef _SPARC_ECC_H +#define _SPARC_ECC_H + +/* These registers are accessed through the SRMMU passthrough ASI 0x20 */ +#define ECC_ENABLE 0x00000000 /* ECC enable register */ +#define ECC_FSTATUS 0x00000008 /* ECC fault status register */ +#define ECC_FADDR 0x00000010 /* ECC fault address register */ +#define ECC_DIGNOSTIC 0x00000018 /* ECC diagnostics register */ +#define ECC_MBAENAB 0x00000020 /* MBus arbiter enable register */ +#define ECC_DMESG 0x00001000 /* Diagnostic message passing area */ + +/* ECC MBus Arbiter Enable register: + * + * ---------------------------------------- + * | |SBUS|MOD3|MOD2|MOD1|RSV| + * ---------------------------------------- + * 31 5 4 3 2 1 0 + * + * SBUS: Enable MBus Arbiter on the SBus 0=off 1=on + * MOD3: Enable MBus Arbiter on MBus module 3 0=off 1=on + * MOD2: Enable MBus Arbiter on MBus module 2 0=off 1=on + * MOD1: Enable MBus Arbiter on MBus module 1 0=off 1=on + */ + +#define ECC_MBAE_SBUS 0x00000010 +#define ECC_MBAE_MOD3 0x00000008 +#define ECC_MBAE_MOD2 0x00000004 +#define ECC_MBAE_MOD1 0x00000002 + +/* ECC Fault Control Register layout: + * + * ----------------------------- + * | RESV | ECHECK | EINT | + * ----------------------------- + * 31 2 1 0 + * + * ECHECK: Enable ECC checking. 0=off 1=on + * EINT: Enable Interrupts for correctable errors. 0=off 1=on + */ +#define ECC_FCR_CHECK 0x00000002 +#define ECC_FCR_INTENAB 0x00000001 + +/* ECC Fault Address Register Zero layout: + * + * ----------------------------------------------------- + * | MID | S | RSV | VA | BM |AT| C| SZ |TYP| PADDR | + * ----------------------------------------------------- + * 31-28 27 26-22 21-14 13 12 11 10-8 7-4 3-0 + * + * MID: ModuleID of the faulting processor. ie. who did it? + * S: Supervisor/Privileged access? 0=no 1=yes + * VA: Bits 19-12 of the virtual faulting address, these are the + * superset bits in the virtual cache and can be used for + * a flush operation if necessary. + * BM: Boot mode? 0=no 1=yes This is just like the SRMMU boot + * mode bit. + * AT: Did this fault happen during an atomic instruction? 0=no + * 1=yes. This means either an 'ldstub' or 'swap' instruction + * was in progress (but not finished) when this fault happened. + * This indicated whether the bus was locked when the fault + * occurred. + * C: Did the pte for this access indicate that it was cacheable? + * 0=no 1=yes + * SZ: The size of the transaction. + * TYP: The transaction type. + * PADDR: Bits 35-32 of the physical address for the fault. + */ +#define ECC_FADDR0_MIDMASK 0xf0000000 +#define ECC_FADDR0_S 0x08000000 +#define ECC_FADDR0_VADDR 0x003fc000 +#define ECC_FADDR0_BMODE 0x00002000 +#define ECC_FADDR0_ATOMIC 0x00001000 +#define ECC_FADDR0_CACHE 0x00000800 +#define ECC_FADDR0_SIZE 0x00000700 +#define ECC_FADDR0_TYPE 0x000000f0 +#define ECC_FADDR0_PADDR 0x0000000f + +/* ECC Fault Address Register One layout: + * + * ------------------------------------- + * | Physical Address 31-0 | + * ------------------------------------- + * 31 0 + * + * You get the upper 4 bits of the physical address from the + * PADDR field in ECC Fault Address Zero register. + */ + +/* ECC Fault Status Register layout: + * + * ---------------------------------------------- + * | RESV|C2E|MULT|SYNDROME|DWORD|UNC|TIMEO|BS|C| + * ---------------------------------------------- + * 31-18 17 16 15-8 7-4 3 2 1 0 + * + * C2E: A C2 graphics error occurred. 0=no 1=yes (SS10 only) + * MULT: Multiple errors occurred ;-O 0=no 1=prom_panic(yes) + * SYNDROME: Controller is mentally unstable. + * DWORD: + * UNC: Uncorrectable error. 0=no 1=yes + * TIMEO: Timeout occurred. 0=no 1=yes + * BS: C2 graphics bad slot access. 0=no 1=yes (SS10 only) + * C: Correctable error? 0=no 1=yes + */ + +#define ECC_FSR_C2ERR 0x00020000 +#define ECC_FSR_MULT 0x00010000 +#define ECC_FSR_SYND 0x0000ff00 +#define ECC_FSR_DWORD 0x000000f0 +#define ECC_FSR_UNC 0x00000008 +#define ECC_FSR_TIMEO 0x00000004 +#define ECC_FSR_BADSLOT 0x00000002 +#define ECC_FSR_C 0x00000001 + +#endif /* !(_SPARC_ECC_H) */ |