diff options
Diffstat (limited to 'arch/arm64')
213 files changed, 14423 insertions, 3077 deletions
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index 6eecdef538bd..c20eacd9a931 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -13,6 +13,11 @@ config ARCH_AGILEX help This enables support for Intel's Agilex SoCFPGA Family. +config ARCH_N5X + bool "Intel's eASIC N5X SoCFPGA Family" + help + This enables support for Intel's eASIC N5X SoCFPGA Family. + config ARCH_SUNXI bool "Allwinner sunxi 64-bit SoC Family" select ARCH_HAS_RESET_CONTROLLER diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 211d1e9d4701..41ce680e5f8d 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts index e5e840b9fbb4..f7fe9fa50cb3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts @@ -36,18 +36,18 @@ leds { compatible = "gpio-leds"; - pwr-led { + led-0 { label = "bananapi-m64:red:pwr"; gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ default-state = "on"; }; - green { + led-1 { label = "bananapi-m64:green:user"; gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */ }; - blue { + led-2 { label = "bananapi-m64:blue:user"; gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts index e58db8a6cab6..09b3c7fb82c0 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts @@ -35,7 +35,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "nanopi-a64:blue:status"; gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts index 302e24be0a31..437ffe3628a5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts @@ -1,10 +1,21 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) // Copyright (c) 2018 ARM Ltd. +#include <dt-bindings/leds/common.h> #include "sun50i-a64-sopine-baseboard.dts" / { model = "Pine64 LTS"; compatible = "pine64,pine64-lts", "allwinner,sun50i-r18", "allwinner,sun50i-a64"; + + leds { + compatible = "gpio-leds"; + + led { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_BLUE>; + gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + }; + }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 896f34fd9fc3..7ae16541d14f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -126,8 +126,6 @@ }; &ehci0 { - phys = <&usbphy 0>; - phy-names = "usb"; status = "okay"; }; @@ -169,6 +167,7 @@ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>; vmmc-supply = <®_dcdc1>; vqmmc-supply = <®_eldo1>; + max-frequency = <200000000>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -177,8 +176,6 @@ }; &ohci0 { - phys = <&usbphy 0>; - phy-names = "usb"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts index 3d5a2ae9aa39..fb65319a3bd3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts @@ -7,7 +7,7 @@ / { model = "Pine64 PinePhone Developer Batch (1.0)"; - compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; + compatible = "pine64,pinephone-1.0", "pine64,pinephone", "allwinner,sun50i-a64"; }; &sgm3140 { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts index c9b9f6e9ee8c..5e59d3752178 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts @@ -7,7 +7,7 @@ / { model = "Pine64 PinePhone Braveheart (1.1)"; - compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; + compatible = "pine64,pinephone-1.1", "pine64,pinephone", "allwinner,sun50i-a64"; }; &backlight { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts index acc0ab53b9c1..4e7e237cb46a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts @@ -7,7 +7,7 @@ / { model = "Pine64 PinePhone (1.2)"; - compatible = "pine64,pinephone-1.2", "allwinner,sun50i-a64"; + compatible = "pine64,pinephone-1.2", "pine64,pinephone", "allwinner,sun50i-a64"; wifi_pwrseq: wifi-pwrseq { compatible = "mmc-pwrseq-simple"; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index 2dfe9bae8c67..9f69d489a81d 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -21,6 +21,7 @@ compatible = "pwm-backlight"; pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ + power-supply = <®_ps>; /* Backlight configuration differs per PinePhone revision. */ }; @@ -31,25 +32,33 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { function = LED_FUNCTION_INDICATOR; color = <LED_COLOR_ID_BLUE>; gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ }; - green { + led-1 { function = LED_FUNCTION_INDICATOR; color = <LED_COLOR_ID_GREEN>; gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ }; - red { + led-2 { function = LED_FUNCTION_INDICATOR; color = <LED_COLOR_ID_RED>; gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ }; }; + reg_ps: ps-regulator { + compatible = "regulator-fixed"; + regulator-name = "ps"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + reg_vbat_wifi: vbat-wifi { compatible = "regulator-fixed"; regulator-min-microvolt = <3300000>; @@ -174,8 +183,6 @@ reg = <0x48>; interrupt-parent = <&pio>; interrupts = <1 0 IRQ_TYPE_EDGE_FALLING>; /* PB0 */ - vdd-supply = <®_ldo_io0>; - leda-supply = <®_dldo1>; }; /* Accelerometer/gyroscope */ @@ -196,6 +203,7 @@ &lradc { vref-supply = <®_aldo3>; + wakeup-source; status = "okay"; button-200 { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts new file mode 100644 index 000000000000..6265360ce623 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Icenowy Zheng <icenowy@aosc.io> + * + */ + +/dts-v1/; + +#include "sun50i-a64-pinetab.dts" + +/ { + model = "PineTab, Early Adopter's version"; + compatible = "pine64,pinetab-early-adopter", "allwinner,sun50i-a64"; +}; + +&dsi { + /delete-node/ panel@0; + + panel@0 { + compatible = "feixin,k101-im2byl02", "ilitek,ili9881c"; + reg = <0>; + power-supply = <®_dc1sw>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ + backlight = <&backlight>; + }; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts index 0494bfaf2ffa..422a8507f674 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts @@ -14,7 +14,7 @@ #include <dt-bindings/pwm/pwm.h> / { - model = "PineTab"; + model = "PineTab, Development Sample"; compatible = "pine64,pinetab", "allwinner,sun50i-a64"; aliases { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts index d4069749d721..e22b94c83647 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts @@ -111,6 +111,7 @@ bus-width = <8>; non-removable; cap-mmc-hw-reset; + mmc-hs200-1_8v; status = "okay"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi index c48692b06e1f..3402cec87035 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi @@ -32,7 +32,6 @@ pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; - non-removable; disable-wp; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts index a1864a89fb89..f0a16f355e27 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts @@ -52,12 +52,12 @@ leds { compatible = "gpio-leds"; - capslock { + led-0 { label = "teres-i:green:capslock"; gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ }; - numlock { + led-1 { label = "teres-i:green:numlock"; gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 51cc30e84e26..57786fc120c3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -514,7 +514,7 @@ resets = <&ccu RST_BUS_MMC2>; reset-names = "ahb"; interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; - max-frequency = <200000000>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -593,6 +593,8 @@ <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>, <&ccu RST_BUS_EHCI0>; + phys = <&usbphy 0>; + phy-names = "usb"; status = "disabled"; }; @@ -603,6 +605,8 @@ clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>; + phys = <&usbphy 0>; + phy-names = "usb"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts index 9d93fe153689..4c3921ac236c 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts @@ -25,13 +25,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "nanopi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "nanopi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts index b059e20813bd..02f8e72f0cad 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts @@ -22,13 +22,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "nanopi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "nanopi:blue:status"; gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts index 8bf2db9dcbda..1010c1b22d2e 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -42,13 +42,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts index 33ab44072e6d..74e0444af19b 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts @@ -36,13 +36,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts index ef5ca6444220..d13980ed7a79 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts @@ -33,13 +33,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts index de19e68eb84e..22530ace12d5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts @@ -33,13 +33,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi index 10489e508695..578a63dedf46 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi @@ -121,6 +121,19 @@ resets = <&ccu RST_BUS_CE>; }; + deinterlace: deinterlace@1e00000 { + compatible = "allwinner,sun8i-h3-deinterlace"; + reg = <0x01e00000 0x20000>; + clocks = <&ccu CLK_BUS_DEINTERLACE>, + <&ccu CLK_DEINTERLACE>, + <&ccu CLK_DRAM_DEINTERLACE>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_DEINTERLACE>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + interconnects = <&mbus 9>; + interconnect-names = "dma-mem"; + }; + mali: gpu@1e80000 { compatible = "allwinner,sun50i-h5-mali", "arm,mali-450"; reg = <0x01e80000 0x30000>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts index 7c9dbde645b5..4f4755152fce 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts @@ -43,7 +43,7 @@ leds { compatible = "gpio-leds"; - power { + led { label = "beelink:white:power"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ default-state = "on"; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi index 1a5eddc5a40f..8c6e8536b69f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi @@ -8,7 +8,7 @@ nvmem-cells = <&cpu_speed_grade>; opp-shared; - opp@480000000 { + opp-480000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <480000000>; @@ -17,7 +17,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@720000000 { + opp-720000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <720000000>; @@ -26,7 +26,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@816000000 { + opp-816000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <816000000>; @@ -35,7 +35,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@888000000 { + opp-888000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <888000000>; @@ -44,7 +44,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@1080000000 { + opp-1080000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1080000000>; @@ -53,7 +53,7 @@ opp-microvolt-speed2 = <880000 880000 1200000>; }; - opp@1320000000 { + opp-1320000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1320000000>; @@ -62,7 +62,7 @@ opp-microvolt-speed2 = <940000 940000 1200000>; }; - opp@1488000000 { + opp-1488000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1488000000>; @@ -71,7 +71,7 @@ opp-microvolt-speed2 = <1000000 1000000 1200000>; }; - opp@1608000000 { + opp-1608000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1608000000>; @@ -80,7 +80,7 @@ opp-microvolt-speed2 = <1030000 1030000 1200000>; }; - opp@1704000000 { + opp-1704000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1704000000>; @@ -89,7 +89,7 @@ opp-microvolt-speed2 = <1060000 1060000 1200000>; }; - opp@1800000000 { + opp-1800000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1800000000>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 15c9dd8c4479..7e83f6146f8a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -43,13 +43,13 @@ leds { compatible = "gpio-leds"; - power { + led-0 { label = "orangepi:red:power"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ default-state = "on"; }; - status { + led-1 { label = "orangepi:green:status"; gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi index ebc120a9232f..da0875bd38d4 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi @@ -42,13 +42,13 @@ leds { compatible = "gpio-leds"; - power { + led-0 { label = "orangepi:red:power"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ default-state = "on"; }; - status { + led-1 { label = "orangepi:green:status"; gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts index 7fea1e4e2d49..686f58e77004 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts @@ -34,3 +34,18 @@ non-removable; status = "okay"; }; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "realtek,rtl8723bs-bt"; + device-wake-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ + host-wake-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ + enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ + max-speed = <1500000>; + }; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts index 961732c52aa0..b868ad17af8f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts @@ -44,17 +44,17 @@ leds { compatible = "gpio-leds"; - heartbeat { + led-0 { label = "pine-h64:green:heartbeat"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ }; - link { + led-1 { label = "pine-h64:white:link"; gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>; /* PL3 */ }; - status { + led-2 { label = "pine-h64:blue:status"; gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ }; @@ -142,6 +142,7 @@ vqmmc-supply = <®_bldo2>; non-removable; cap-mmc-hw-reset; + mmc-hs200-1_8v; bus-width = <8>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 8a62a9fbe347..49e979794094 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -436,6 +436,7 @@ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -452,6 +453,7 @@ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -468,6 +470,7 @@ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -680,6 +683,8 @@ <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>, <&ccu RST_BUS_EHCI0>; + phys = <&usb2phy 0>; + phy-names = "usb"; status = "disabled"; }; @@ -690,6 +695,8 @@ clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>; + phys = <&usb2phy 0>; + phy-names = "usb"; status = "disabled"; }; @@ -949,6 +956,11 @@ pins = "PL9"; function = "s_cir_rx"; }; + + r_rsb_pins: r-rsb-pins { + pins = "PL0", "PL1"; + function = "s_rsb"; + }; }; r_ir: ir@7040000 { @@ -979,6 +991,20 @@ #size-cells = <0>; }; + r_rsb: rsb@7083000 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x07083000 0x400>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu 13>; + clock-frequency = <3000000>; + resets = <&r_ccu 7>; + pinctrl-names = "default"; + pinctrl-0 = <&r_rsb_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + ths: thermal-sensor@5070400 { compatible = "allwinner,sun50i-h6-ths"; reg = <0x05070400 0x100>; diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi index 0f893984c256..d301ac0d406b 100644 --- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi @@ -203,7 +203,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <24>; + ngpios = <24>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -223,7 +223,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <24>; + ngpios = <24>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index ced03946314f..78a569d7fa20 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb @@ -44,7 +45,8 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-libretech-pc.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb -dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-c4.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-hc4.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi index ba1c6dfdc4b6..d945c84ab697 100644 --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi @@ -280,8 +280,6 @@ "timing-adjustment"; rx-fifo-depth = <4096>; tx-fifo-depth = <2048>; - resets = <&reset RESET_ETHERNET>; - reset-names = "stmmaceth"; power-domains = <&pwrc PWRC_AXG_ETHERNET_MEM_ID>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi index 9c90d562ada1..b858c5e43cc8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi @@ -224,8 +224,6 @@ "timing-adjustment"; rx-fifo-depth = <4096>; tx-fifo-depth = <2048>; - resets = <&reset RESET_ETHERNET>; - reset-names = "stmmaceth"; status = "disabled"; mdio0: mdio { @@ -2390,7 +2388,7 @@ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "host"; snps,dis_u2_susphy_quirk; - snps,quirk-frame-length-adjustment; + snps,quirk-frame-length-adjustment = <0x20>; snps,parkmode-disable-ss-quirk; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts index b00d0468c753..81269ccc2496 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts @@ -181,7 +181,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12A-SEI510"; + model = "SEI510"; audio-aux-devs = <&tdmout_a>, <&tdmout_b>, <&tdmin_a>, <&tdmin_b>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts index 463a72d6bb7c..579f3d02d613 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts @@ -150,7 +150,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12A-X96-MAX"; + model = "X96-MAX"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts new file mode 100644 index 000000000000..211191f66344 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts @@ -0,0 +1,133 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com> + */ + +/dts-v1/; + +#include "meson-g12b-w400.dtsi" +#include <dt-bindings/leds/common.h> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h> + +/ { + compatible = "azw,gsking-x", "amlogic,g12b"; + model = "Beelink GS-King X"; + + aliases { + rtc0 = &rtc; + rtc1 = &vrtc; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + power-button { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>; + }; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + model = "GSKING-X"; + audio-aux-devs = <&tdmout_a>; + audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 1", + "TDMOUT_A IN 1", "FRDDR_B OUT 1", + "TDMOUT_A IN 2", "FRDDR_C OUT 1", + "TDM_A Playback", "TDMOUT_A OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + status = "okay"; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_a>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>; + }; + }; + + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&arb { + status = "okay"; +}; + +&clkc_audio { + status = "okay"; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + +&tdmif_a { + status = "okay"; +}; + +&tdmout_a { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts index 0e5c500fb78f..0e331aa5a2d7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts @@ -44,7 +44,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-GTKING-PRO"; + model = "GTKING-PRO"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts index 10b87eb97b14..a7db84a500bb 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts @@ -28,7 +28,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-GTKING"; + model = "GTKING"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index 39a09661c5f6..58ce569b2ace 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi @@ -13,6 +13,8 @@ aliases { serial0 = &uart_AO; ethernet0 = ðmac; + rtc0 = &rtc; + rtc1 = &vrtc; }; dioo2133: audio-amplifier-0 { @@ -211,7 +213,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-ODROID-N2"; + model = "ODROID-N2"; audio-widgets = "Line", "Lineout"; audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>, <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>, @@ -478,6 +480,18 @@ linux,rc-map-name = "rc-odroid"; }; +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + &pwm_ab { pinctrl-0 = <&pwm_a_e_pins>; pinctrl-names = "default"; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts index b57bb0befc69..0c7892600d56 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts @@ -23,7 +23,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-UGOOS-AM6"; + model = "UGOOS-AM6"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi index c2480bab8d33..2d7032f41e4b 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi @@ -186,7 +186,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S9XX-PC"; + model = "LIBRETECH-PC"; audio-aux-devs = <&dio2133>; audio-widgets = "Speaker", "7J4-14 LEFT", "Speaker", "7J4-11 RIGHT"; diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi index 6b57e15aade3..dafc841f7c16 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi @@ -121,7 +121,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GX-P230-Q200"; + model = "P230-Q200"; audio-aux-devs = <&dio2133>; audio-widgets = "Line", "Lineout"; audio-routing = "AU2 INL", "ACODEC LOLP", diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index 726b91d3a905..0edd137151f8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi @@ -13,7 +13,6 @@ #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/meson-gxbb-power.h> -#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h> #include <dt-bindings/thermal/thermal.h> / { @@ -576,8 +575,6 @@ interrupt-names = "macirq"; rx-fifo-depth = <4096>; tx-fifo-depth = <2048>; - resets = <&reset RESET_ETHERNET>; - reset-names = "stmmaceth"; power-domains = <&pwrc PWRC_GXBB_ETHERNET_MEM_ID>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts index 089e0636ba8a..7273eed5292c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts @@ -134,7 +134,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-NANOPI-K2"; + model = "NANOPI-K2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index b5b11cb9f393..f887bfb445fd 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts @@ -143,7 +143,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-NEXBOX-A95X"; + model = "NEXBOX-A95X"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index c04ef57f7b3b..bfaf7f41a2d6 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -176,7 +176,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-ODROID-C2"; + model = "ODROID-C2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts index 0c1570153842..58733017eda8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts @@ -15,7 +15,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-WETEK-HUB"; + model = "WETEK-HUB"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts index f2562c7de67c..6eae692792ec 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts @@ -50,7 +50,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-WETEK-PLAY2"; + model = "WETEK-PLAY2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts index 9e43f4dca90d..2d769203f671 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts @@ -118,7 +118,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S805X-AC"; + model = "LIBRETECH-AC"; audio-widgets = "Speaker", "9J5-3 LEFT", "Speaker", "9J5-2 RIGHT"; audio-routing = "9J5-3 LEFT", "ACODEC LOLN", diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts index 6fe589cd2ba2..60feac0179c0 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts @@ -42,10 +42,10 @@ }; }; - pwmleds { + led-controller { compatible = "pwm-leds"; - power { + led-1 { label = "vim:red:power"; pwms = <&pwm_AO_ab 1 7812500 0>; max-brightness = <255>; @@ -66,7 +66,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-KHADAS-VIM1"; + model = "KHADAS-VIM"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts index 9a3c08e6e6cc..93d8f8aff70d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts @@ -159,7 +159,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S905X-CC-V2"; + model = "LIBRETECH-CC-V2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts index 5ae7bb6209cb..82bfabfbd39c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts @@ -135,7 +135,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S905X-CC"; + model = "LIBRETECH-CC"; audio-aux-devs = <&dio2133>; audio-widgets = "Line", "Lineout"; audio-routing = "AU2 INL", "ACODEC LOLN", diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts index bf9877d33427..18a4b7a6c5df 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts @@ -81,10 +81,10 @@ }; }; - pwmleds { + led-controller { compatible = "pwm-leds"; - power { + led-1 { label = "vim:red:power"; pwms = <&pwm_AO_ab 1 7812500 0>; max-brightness = <255>; @@ -148,7 +148,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXM-KHADAS-VIM2"; + model = "KHADAS-VIM2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi index 8f8656262ae7..877e3b989203 100644 --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi @@ -170,7 +170,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-KHADAS-VIM3"; + model = "KHADAS-VIM3"; audio-aux-devs = <&tdmout_a>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", "TDMOUT_A IN 1", "FRDDR_B OUT 0", @@ -283,12 +283,12 @@ }; ðmac { - pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&external_phy>; - amlogic,tx-delay-ns = <2>; + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; }; &frddr_a { @@ -354,9 +354,9 @@ }; &pwm_ef { - status = "okay"; - pinctrl-0 = <&pwm_e_pins>; - pinctrl-names = "default"; + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; }; &saradc { @@ -450,7 +450,6 @@ }; }; - &tdmif_a { status = "okay"; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts index 4b517ca72059..06de0b1ce726 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts @@ -89,13 +89,12 @@ status = "okay"; }; -&sd_emmc_a { - sd-uhs-sdr50; -}; - &usb { phys = <&usb2_phy0>, <&usb2_phy1>; phy-names = "usb2-phy0", "usb2-phy1"; }; */ +&sd_emmc_a { + sd-uhs-sdr50; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts index cf5a98f0e47c..b2a4e823c1d8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts @@ -5,34 +5,12 @@ /dts-v1/; -#include "meson-sm1.dtsi" -#include <dt-bindings/gpio/meson-g12a-gpio.h> -#include <dt-bindings/leds/common.h> -#include <dt-bindings/sound/meson-g12a-tohdmitx.h> +#include "meson-sm1-odroid.dtsi" / { compatible = "hardkernel,odroid-c4", "amlogic,sm1"; model = "Hardkernel ODROID-C4"; - aliases { - serial0 = &uart_AO; - ethernet0 = ðmac; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x40000000>; - }; - - emmc_pwrseq: emmc-pwrseq { - compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; - }; - leds { compatible = "gpio-leds"; @@ -45,96 +23,6 @@ }; }; - tflash_vdd: regulator-tflash_vdd { - compatible = "regulator-fixed"; - - regulator-name = "TFLASH_VDD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>; - enable-active-high; - regulator-always-on; - }; - - tf_io: gpio-regulator-tf_io { - compatible = "regulator-gpio"; - - regulator-name = "TF_IO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - - states = <3300000 0>, - <1800000 1>; - }; - - flash_1v8: regulator-flash_1v8 { - compatible = "regulator-fixed"; - regulator-name = "FLASH_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - main_12v: regulator-main_12v { - compatible = "regulator-fixed"; - regulator-name = "12V"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-always-on; - }; - - vcc_5v: regulator-vcc_5v { - compatible = "regulator-fixed"; - regulator-name = "5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - vin-supply = <&main_12v>; - }; - - vcc_1v8: regulator-vcc_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VCC_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - vcc_3v3: regulator-vcc_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - /* FIXME: actually controlled by VDDCPU_B_EN */ - }; - - vddcpu: regulator-vddcpu { - /* - * MP8756GD Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDCPU"; - regulator-min-microvolt = <721000>; - regulator-max-microvolt = <1022000>; - - vin-supply = <&main_12v>; - - pwms = <&pwm_AO_cd 1 1250 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - hub_5v: regulator-hub_5v { compatible = "regulator-fixed"; regulator-name = "HUB_5V"; @@ -147,215 +35,12 @@ enable-active-high; }; - usb_pwr_en: regulator-usb_pwr_en { - compatible = "regulator-fixed"; - regulator-name = "USB_PWR_EN"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <&vcc_5v>; - - /* Connected to the microUSB port power enable */ - gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - vddao_1v8: regulator-vddao_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - }; - - vddao_3v3: regulator-vddao_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&main_12v>; - regulator-always-on; - }; - - hdmi-connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&hdmi_tx_tmds_out>; - }; - }; - }; - sound { - compatible = "amlogic,axg-sound-card"; - model = "SM1-ODROID-C4"; - audio-aux-devs = <&tdmout_b>; - audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", - "TDMOUT_B IN 1", "FRDDR_B OUT 1", - "TDMOUT_B IN 2", "FRDDR_C OUT 1", - "TDM_B Playback", "TDMOUT_B OUT"; - - assigned-clocks = <&clkc CLKID_MPLL2>, - <&clkc CLKID_MPLL0>, - <&clkc CLKID_MPLL1>; - assigned-clock-parents = <0>, <0>, <0>; - assigned-clock-rates = <294912000>, - <270950400>, - <393216000>; - status = "okay"; - - dai-link-0 { - sound-dai = <&frddr_a>; - }; - - dai-link-1 { - sound-dai = <&frddr_b>; - }; - - dai-link-2 { - sound-dai = <&frddr_c>; - }; - - /* 8ch hdmi interface */ - dai-link-3 { - sound-dai = <&tdmif_b>; - dai-format = "i2s"; - dai-tdm-slot-tx-mask-0 = <1 1>; - dai-tdm-slot-tx-mask-1 = <1 1>; - dai-tdm-slot-tx-mask-2 = <1 1>; - dai-tdm-slot-tx-mask-3 = <1 1>; - mclk-fs = <256>; - - codec { - sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; - }; - }; - - /* hdmi glue */ - dai-link-4 { - sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; - - codec { - sound-dai = <&hdmi_tx>; - }; - }; - }; -}; - -&arb { - status = "okay"; -}; - -&clkc_audio { - status = "okay"; -}; - -&cpu0 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU_CLK>; - clock-latency = <50000>; -}; - -&cpu1 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU1_CLK>; - clock-latency = <50000>; -}; - -&cpu2 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU2_CLK>; - clock-latency = <50000>; -}; - -&cpu3 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU3_CLK>; - clock-latency = <50000>; -}; - -&ext_mdio { - external_phy: ethernet-phy@0 { - /* Realtek RTL8211F (0x001cc916) */ - reg = <0>; - max-speed = <1000>; - - interrupt-parent = <&gpio_intc>; - /* MAC_INTR on GPIOZ_14 */ - interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + model = "ODROID-C4"; }; }; -ðmac { - pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&external_phy>; - amlogic,tx-delay-ns = <2>; -}; - -&frddr_a { - status = "okay"; -}; - -&frddr_b { - status = "okay"; -}; - -&frddr_c { - status = "okay"; -}; - &gpio { - gpio-line-names = - /* GPIOZ */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - /* GPIOH */ - "", "", "", "", "", - "PIN_36", /* GPIOH_5 */ - "PIN_26", /* GPIOH_6 */ - "PIN_32", /* GPIOH_7 */ - "", - /* BOOT */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - /* GPIOC */ - "", "", "", "", "", "", "", "", - /* GPIOA */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", - "PIN_27", /* GPIOA_14 */ - "PIN_28", /* GPIOA_15 */ - /* GPIOX */ - "PIN_16", /* GPIOX_0 */ - "PIN_18", /* GPIOX_1 */ - "PIN_22", /* GPIOX_2 */ - "PIN_11", /* GPIOX_3 */ - "PIN_13", /* GPIOX_4 */ - "PIN_7", /* GPIOX_5 */ - "PIN_33", /* GPIOX_6 */ - "PIN_15", /* GPIOX_7 */ - "PIN_19", /* GPIOX_8 */ - "PIN_21", /* GPIOX_9 */ - "PIN_24", /* GPIOX_10 */ - "PIN_23", /* GPIOX_11 */ - "PIN_8", /* GPIOX_12 */ - "PIN_10", /* GPIOX_13 */ - "PIN_29", /* GPIOX_14 */ - "PIN_31", /* GPIOX_15 */ - "PIN_12", /* GPIOX_16 */ - "PIN_3", /* GPIOX_17 */ - "PIN_5", /* GPIOX_18 */ - "PIN_35"; /* GPIOX_19 */ - /* * WARNING: The USB Hub on the Odroid-C4 needs a reset signal * to be turned high in order to be detected by the USB Controller @@ -370,120 +55,10 @@ }; }; -&gpio_ao { - gpio-line-names = - /* GPIOAO */ - "", "", "", "", - "PIN_47", /* GPIOAO_4 */ - "", "", - "PIN_45", /* GPIOAO_7 */ - "PIN_46", /* GPIOAO_8 */ - "PIN_44", /* GPIOAO_9 */ - "PIN_42", /* GPIOAO_10 */ - "", - /* GPIOE */ - "", "", ""; -}; - -&hdmi_tx { - status = "okay"; - pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; - pinctrl-names = "default"; - hdmi-supply = <&vcc_5v>; -}; - -&hdmi_tx_tmds_port { - hdmi_tx_tmds_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - }; -}; - &ir { - status = "okay"; - pinctrl-0 = <&remote_input_ao_pins>; - pinctrl-names = "default"; linux,rc-map-name = "rc-odroid"; }; -&pwm_AO_cd { - pinctrl-0 = <&pwm_ao_d_e_pins>; - pinctrl-names = "default"; - clocks = <&xtal>; - clock-names = "clkin1"; - status = "okay"; -}; - -&saradc { - status = "okay"; -}; - -/* SD card */ -&sd_emmc_b { - status = "okay"; - pinctrl-0 = <&sdcard_c_pins>; - pinctrl-1 = <&sdcard_clk_gate_c_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <4>; - cap-sd-highspeed; - max-frequency = <200000000>; - sd-uhs-sdr12; - sd-uhs-sdr25; - sd-uhs-sdr50; - sd-uhs-sdr104; - disable-wp; - - cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; - vmmc-supply = <&tflash_vdd>; - vqmmc-supply = <&tf_io>; -}; - -/* eMMC */ -&sd_emmc_c { - status = "okay"; - pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; - pinctrl-1 = <&emmc_clk_gate_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <8>; - cap-mmc-highspeed; - mmc-ddr-1_8v; - mmc-hs200-1_8v; - max-frequency = <200000000>; - disable-wp; - - mmc-pwrseq = <&emmc_pwrseq>; - vmmc-supply = <&vcc_3v3>; - vqmmc-supply = <&flash_1v8>; -}; - -&tdmif_b { - status = "okay"; -}; - -&tdmout_b { - status = "okay"; -}; - -&tohdmitx { - status = "okay"; -}; - -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_pwr_en>; -}; - -&usb2_phy0 { - phy-supply = <&vcc_5v>; -}; - &usb2_phy1 { /* Enable the hub which is connected to this port */ phy-supply = <&hub_5v>; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts new file mode 100644 index 000000000000..bf15700c4b15 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com> + */ + +/dts-v1/; + +#include "meson-sm1-odroid.dtsi" + +/ { + compatible = "hardkernel,odroid-hc4", "amlogic,sm1"; + model = "Hardkernel ODROID-HC4"; + + aliases { + rtc0 = &rtc; + rtc1 = &vrtc; + }; + + fan0: pwm-fan { + compatible = "pwm-fan"; + #cooling-cells = <2>; + cooling-min-state = <0>; + cooling-max-state = <3>; + cooling-levels = <0 120 170 220>; + pwms = <&pwm_cd 1 40000 0>; + }; + + leds { + compatible = "gpio-leds"; + + led-blue { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_STATUS; + gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + panic-indicator; + }; + + led-red { + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_POWER; + gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + sound { + model = "ODROID-HC4"; + }; +}; + +&cpu_thermal { + cooling-maps { + map { + trip = <&cpu_passive>; + cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; +}; + +&ir { + linux,rc-map-name = "rc-odroid"; +}; + +&i2c2 { + status = "okay"; + pinctrl-0 = <&i2c2_sda_x_pins>, <&i2c2_sck_x_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + status = "okay"; + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + +&pcie { + status = "okay"; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; +}; + +&pwm_cd { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_d_x6_pins>; +}; + +&sd_emmc_c { + status = "disabled"; +}; + +&usb { + phys = <&usb2_phy0>, <&usb2_phy1>; + phy-names = "usb2-phy0", "usb2-phy1"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi new file mode 100644 index 000000000000..d14716b3d0f1 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi @@ -0,0 +1,442 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com> + */ + +#include "meson-sm1.dtsi" +#include <dt-bindings/gpio/meson-g12a-gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h> + +/ { + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + tflash_vdd: regulator-tflash_vdd { + compatible = "regulator-fixed"; + + regulator-name = "TFLASH_VDD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>; + enable-active-high; + regulator-always-on; + }; + + tf_io: gpio-regulator-tf_io { + compatible = "regulator-gpio"; + + regulator-name = "TF_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + + states = <3300000 0>, + <1800000 1>; + }; + + flash_1v8: regulator-flash_1v8 { + compatible = "regulator-fixed"; + regulator-name = "FLASH_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + main_12v: regulator-main_12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&main_12v>; + }; + + vcc_1v8: regulator-vcc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + /* FIXME: actually controlled by VDDCPU_B_EN */ + }; + + vddcpu: regulator-vddcpu { + /* + * MP8756GD Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + usb_pwr_en: regulator-usb_pwr_en { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR_EN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the microUSB port power enable */ + gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vddao_1v8: regulator-vddao_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&main_12v>; + regulator-always-on; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + audio-aux-devs = <&tdmout_b>; + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", + "TDMOUT_B IN 1", "FRDDR_B OUT 1", + "TDMOUT_B IN 2", "FRDDR_C OUT 1", + "TDM_B Playback", "TDMOUT_B OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + status = "okay"; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_b>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; + }; + }; + + /* hdmi glue */ + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&arb { + status = "okay"; +}; + +&clkc_audio { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU1_CLK>; + clock-latency = <50000>; +}; + +&cpu2 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU2_CLK>; + clock-latency = <50000>; +}; + +&cpu3 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU3_CLK>; + clock-latency = <50000>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_14 */ + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +&gpio { + gpio-line-names = + /* GPIOZ */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOH */ + "", "", "", "", "", + "PIN_36", /* GPIOH_5 */ + "PIN_26", /* GPIOH_6 */ + "PIN_32", /* GPIOH_7 */ + "", + /* BOOT */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOC */ + "", "", "", "", "", "", "", "", + /* GPIOA */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", + "PIN_27", /* GPIOA_14 */ + "PIN_28", /* GPIOA_15 */ + /* GPIOX */ + "PIN_16", /* GPIOX_0 */ + "PIN_18", /* GPIOX_1 */ + "PIN_22", /* GPIOX_2 */ + "PIN_11", /* GPIOX_3 */ + "PIN_13", /* GPIOX_4 */ + "PIN_7", /* GPIOX_5 */ + "PIN_33", /* GPIOX_6 */ + "PIN_15", /* GPIOX_7 */ + "PIN_19", /* GPIOX_8 */ + "PIN_21", /* GPIOX_9 */ + "PIN_24", /* GPIOX_10 */ + "PIN_23", /* GPIOX_11 */ + "PIN_8", /* GPIOX_12 */ + "PIN_10", /* GPIOX_13 */ + "PIN_29", /* GPIOX_14 */ + "PIN_31", /* GPIOX_15 */ + "PIN_12", /* GPIOX_16 */ + "PIN_3", /* GPIOX_17 */ + "PIN_5", /* GPIOX_18 */ + "PIN_35"; /* GPIOX_19 */ +}; + +&gpio_ao { + gpio-line-names = + /* GPIOAO */ + "", "", "", "", + "PIN_47", /* GPIOAO_4 */ + "", "", + "PIN_45", /* GPIOAO_7 */ + "PIN_46", /* GPIOAO_8 */ + "PIN_44", /* GPIOAO_9 */ + "PIN_42", /* GPIOAO_10 */ + "", + /* GPIOE */ + "", "", ""; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; + pinctrl-names = "default"; + hdmi-supply = <&vcc_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + +&saradc { + status = "okay"; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <200000000>; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&tf_io>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&flash_1v8>; +}; + +&tdmif_b { + status = "okay"; +}; + +&tdmout_b { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_pwr_en>; +}; + +&usb2_phy0 { + phy-supply = <&vcc_5v>; +}; + diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts index 5ab139a34c01..2194a778973f 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts @@ -101,20 +101,20 @@ }; }; - leds { + led-controller-1 { compatible = "gpio-leds"; - led-bluetooth { + led-1 { label = "sei610:blue:bt"; gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; default-state = "off"; }; }; - pwmleds { + led-controller-2 { compatible = "pwm-leds"; - power { + led-2 { label = "sei610:red:power"; pwms = <&pwm_AO_ab 0 30518 0>; max-brightness = <255>; @@ -220,7 +220,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "SM1-SEI610"; + model = "SEI610"; audio-aux-devs = <&tdmout_a>, <&tdmout_b>, <&tdmin_a>, <&tdmin_b>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile index ef26c23603ce..ebebc0cd421f 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile +++ b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile @@ -1,2 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_BCM4908) += bcm4906-netgear-r8000p.dtb dtb-$(CONFIG_ARCH_BCM4908) += bcm4908-asus-gt-ac5300.dtb diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts new file mode 100644 index 000000000000..ee3ed612274c --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts @@ -0,0 +1,52 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +#include "bcm4906.dtsi" + +/ { + compatible = "netgear,r8000p", "brcm,bcm4906", "brcm,bcm4908"; + model = "Netgear R8000P"; + + memory@0 { + device_type = "memory"; + reg = <0x00 0x00 0x00 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + + wps { + function = LED_FUNCTION_WPS; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&nandcs { + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + + #address-cells = <1>; + #size-cells = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "cferom"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "firmware"; + reg = <0x100000 0x4400000>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi new file mode 100644 index 000000000000..66023d553524 --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "bcm4908.dtsi" + +/ { + cpus { + /delete-node/ cpu@2; + + /delete-node/ cpu@3; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; +}; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts index 13c6b86eef21..6e4ad66ff536 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts @@ -44,6 +44,57 @@ }; }; +&ports { + port@0 { + label = "lan2"; + }; + + port@1 { + label = "lan1"; + }; + + port@2 { + label = "lan6"; + }; + + port@3 { + label = "lan5"; + }; + + /* External BCM53134S switch */ + port@7 { + label = "sw"; + reg = <7>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; +}; + +&mdio { + /* lan8 */ + ethernet-phy@0 { + reg = <0>; + }; + + /* lan7 */ + ethernet-phy@1 { + reg = <1>; + }; + + /* lan4 */ + ethernet-phy@2 { + reg = <2>; + }; + + /* lan3 */ + ethernet-phy@3 { + reg = <3>; + }; +}; + &nandcs { nand-ecc-strength = <4>; nand-ecc-step-size = <512>; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi index f873dc44ce9c..9354077f74cd 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi @@ -108,7 +108,7 @@ compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; - ranges = <0x00 0x00 0x80000000 0x10000>; + ranges = <0x00 0x00 0x80000000 0x281000>; usb@c300 { compatible = "generic-ehci"; @@ -130,6 +130,104 @@ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; + + ethernet-switch@80000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0x80000 0x50000>; + + ethernet-switch@0 { + compatible = "brcm,bcm4908-switch"; + reg = <0x0 0x40000>, + <0x40000 0x110>, + <0x40340 0x30>, + <0x40380 0x30>, + <0x40600 0x34>, + <0x40800 0x208>; + reg-names = "core", "reg", "intrl2_0", + "intrl2_1", "fcb", "acb"; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; + brcm,num-gphy = <5>; + brcm,num-rgmii-ports = <2>; + + #address-cells = <1>; + #size-cells = <0>; + + ports: ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "internal"; + phy-handle = <&phy8>; + }; + + port@1 { + reg = <1>; + phy-mode = "internal"; + phy-handle = <&phy9>; + }; + + port@2 { + reg = <2>; + phy-mode = "internal"; + phy-handle = <&phy10>; + }; + + port@3 { + reg = <3>; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + }; + }; + + mdio: mdio@405c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x405c0 0x8>; + reg-names = "mdio"; + #size-cells = <0>; + #address-cells = <1>; + + phy8: ethernet-phy@8 { + reg = <8>; + }; + + phy9: ethernet-phy@9 { + reg = <9>; + }; + + phy10: ethernet-phy@a { + reg = <10>; + }; + + phy11: ethernet-phy@b { + reg = <11>; + }; + + phy12: ethernet-phy@c { + reg = <12>; + }; + }; + }; + + procmon: syscon@280000 { + compatible = "simple-bus"; + reg = <0x280000 0x1000>; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + power-controller@2800c0 { + compatible = "brcm,bcm4908-pmb"; + reg = <0x2800c0 0x40>; + #power-domain-cells = <1>; + }; + }; }; bus@ff800000 { @@ -164,7 +262,7 @@ nand@1800 { #address-cells = <1>; #size-cells = <0>; - compatible = "brcm,brcmnand-v7.1", "brcm,brcmnand"; + compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand"; reg = <0x1800 0x600>, <0x2000 0x10>; reg-names = "nand", "nand-int-base"; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; @@ -177,6 +275,21 @@ }; }; + misc@2600 { + compatible = "brcm,misc", "simple-mfd"; + reg = <0x2600 0xe4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x2600 0xe4>; + + reset-controller@2644 { + compatible = "brcm,bcm4908-misc-pcie-reset"; + reg = <0x44 0x04>; + #reset-cells = <1>; + }; + }; + reboot { compatible = "syscon-reboot"; regmap = <&timer>; diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi index 43aa5e9c0020..8fe7325cfbb2 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi @@ -56,70 +56,6 @@ }; }; -&sata0 { - status = "okay"; -}; - -&sata_phy0{ - status = "okay"; -}; - -&sata1 { - status = "okay"; -}; - -&sata_phy1{ - status = "okay"; -}; - -&sata2 { - status = "okay"; -}; - -&sata_phy2{ - status = "okay"; -}; - -&sata3 { - status = "okay"; -}; - -&sata_phy3{ - status = "okay"; -}; - -&sata4 { - status = "okay"; -}; - -&sata_phy4{ - status = "okay"; -}; - -&sata5 { - status = "okay"; -}; - -&sata_phy5{ - status = "okay"; -}; - -&sata6 { - status = "okay"; -}; - -&sata_phy6{ - status = "okay"; -}; - -&sata7 { - status = "okay"; -}; - -&sata_phy7{ - status = "okay"; -}; - &pwm { status = "okay"; }; diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi deleted file mode 100644 index 8c68e0c26f1b..000000000000 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi +++ /dev/null @@ -1,278 +0,0 @@ -/* - * BSD LICENSE - * - * Copyright(c) 2016-2017 Broadcom. All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * * Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * * Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in - * the documentation and/or other materials provided with the - * distribution. - * * Neither the name of Broadcom nor the names of its - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - */ - - sata { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x0 0x67d00000 0x00800000>; - - sata0: ahci@0 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00000000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata0_port0: sata-port@0 { - reg = <0>; - phys = <&sata0_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy0: sata_phy@2100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00002100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata0_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata1: ahci@10000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00010000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata1_port0: sata-port@0 { - reg = <0>; - phys = <&sata1_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy1: sata_phy@12100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00012100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata1_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata2: ahci@20000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00020000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata2_port0: sata-port@0 { - reg = <0>; - phys = <&sata2_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy2: sata_phy@22100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00022100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata2_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata3: ahci@30000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00030000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata3_port0: sata-port@0 { - reg = <0>; - phys = <&sata3_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy3: sata_phy@32100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00032100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata3_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata4: ahci@100000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00100000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata4_port0: sata-port@0 { - reg = <0>; - phys = <&sata4_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy4: sata_phy@102100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00102100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata4_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata5: ahci@110000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00110000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata5_port0: sata-port@0 { - reg = <0>; - phys = <&sata5_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy5: sata_phy@112100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00112100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata5_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata6: ahci@120000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00120000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata6_port0: sata-port@0 { - reg = <0>; - phys = <&sata6_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy6: sata_phy@122100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00122100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata6_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata7: ahci@130000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00130000 0x1000>; - reg-names = "ahci"; - interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata7_port0: sata-port@0 { - reg = <0>; - phys = <&sata7_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy7: sata_phy@132100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00132100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata7_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - }; diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi index b425b12c3ed2..2ffb2c92182a 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi @@ -285,7 +285,6 @@ }; #include "stingray-fs4.dtsi" - #include "stingray-sata.dtsi" #include "stingray-pcie.dtsi" #include "stingray-usb.dtsi" @@ -309,12 +308,6 @@ #size-cells = <0>; }; - mdio@2 { /* SATA */ - reg = <0x2>; - #address-cells = <1>; - #size-cells = <0>; - }; - mdio@3 { /* USB */ reg = <0x3>; #address-cells = <1>; diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi index 03486a8ffc67..413cac63a1cb 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi @@ -388,7 +388,7 @@ pmic@66 { compatible = "samsung,s2mps13-pmic"; interrupt-parent = <&gpa0>; - interrupts = <7 IRQ_TYPE_NONE>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; reg = <0x66>; samsung,s2mps11-wrstbi-ground; @@ -793,7 +793,7 @@ compatible = "samsung,s3fwrn5-i2c"; reg = <0x27>; interrupt-parent = <&gpa1>; - interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <3 IRQ_TYPE_EDGE_RISING>; en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>; wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts index 695d4c140646..125c03f351d9 100644 --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts @@ -90,7 +90,7 @@ pmic@66 { compatible = "samsung,s2mps15-pmic"; reg = <0x66>; - interrupts = <2 IRQ_TYPE_NONE>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; interrupt-parent = <&gpa0>; pinctrl-names = "default"; pinctrl-0 = <&pmic_irq>; diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi index 49c19c6879f9..cab89dc6f596 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi @@ -1113,7 +1113,7 @@ thermal-zones { - cls0: cls0 { + cls0: cls0-thermal { polling-delay = <1000>; polling-delay-passive = <100>; sustainable-power = <4500>; @@ -1122,13 +1122,13 @@ thermal-sensors = <&tsensor 1>; trips { - threshold: trip-point@0 { + threshold: trip-point0 { temperature = <65000>; hysteresis = <1000>; type = "passive"; }; - target: trip-point@1 { + target: trip-point1 { temperature = <75000>; hysteresis = <1000>; type = "passive"; diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi index 85b0dfb35d6d..8830795c8efc 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi @@ -194,6 +194,12 @@ #clock-cells = <1>; }; + iomcu_rst: reset { + compatible = "hisilicon,hi3660-reset"; + hisi,rst-syscon = <&iomcu>; + #reset-cells = <2>; + }; + uart0: serial@fdf02000 { compatible = "arm,pl011", "arm,primecell"; reg = <0x0 0xfdf02000 0x0 0x1000>; @@ -708,5 +714,76 @@ card-detect-delay = <200>; status = "disabled"; }; + + /* I2C */ + i2c0: i2c@ffd71000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xffd71000 0x0 0x1000>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&iomcu HI3670_CLK_GATE_I2C0>; + resets = <&iomcu_rst 0x20 3>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pmx_func &i2c0_cfg_func>; + status = "disabled"; + }; + + i2c1: i2c@ffd72000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xffd72000 0x0 0x1000>; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&iomcu HI3670_CLK_GATE_I2C1>; + resets = <&iomcu_rst 0x20 4>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pmx_func &i2c1_cfg_func>; + status = "disabled"; + }; + + i2c2: i2c@ffd73000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xffd73000 0x0 0x1000>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&iomcu HI3670_CLK_GATE_I2C2>; + resets = <&iomcu_rst 0x20 5>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pmx_func &i2c2_cfg_func>; + status = "disabled"; + }; + + i2c3: i2c@fdf0c000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xfdf0c000 0x0 0x1000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&crg_ctrl HI3670_CLK_GATE_I2C3>; + resets = <&crg_rst 0x78 7>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pmx_func &i2c3_cfg_func>; + status = "disabled"; + }; + + i2c4: i2c@fdf0d000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xfdf0d000 0x0 0x1000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&crg_ctrl HI3670_CLK_GATE_I2C4>; + resets = <&crg_rst 0x78 27>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi index 81d09434c5c6..a83b9d4f172e 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi @@ -113,7 +113,7 @@ #size-cells = <1>; ranges = <0x0 0x8a20000 0x1000>; - usb2_phy1: usb2-phy@120 { + usb2_phy1: usb2_phy@120 { compatible = "hisilicon,hi3798cv200-usb2-phy"; reg = <0x120 0x4>; clocks = <&crg HISTB_USB2_PHY1_REF_CLK>; @@ -134,7 +134,7 @@ }; }; - usb2_phy2: usb2-phy@124 { + usb2_phy2: usb2_phy@124 { compatible = "hisilicon,hi3798cv200-usb2-phy"; reg = <0x124 0x4>; clocks = <&crg HISTB_USB2_PHY2_REF_CLK>; @@ -565,8 +565,8 @@ device_type = "pci"; bus-range = <0x00 0xff>; num-lanes = <1>; - ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000 - 0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>; + ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000>, + <0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>; interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi"; #interrupt-cells = <1>; diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index c6580c9f068e..d426c6c8722b 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -872,7 +872,7 @@ thermal-zones { - cls0: cls0 { + cls0: cls0-thermal { polling-delay = <1000>; polling-delay-passive = <100>; sustainable-power = <3326>; @@ -881,13 +881,13 @@ thermal-sensors = <&tsensor 2>; trips { - threshold: trip-point@0 { + threshold: trip-point0 { temperature = <65000>; hysteresis = <0>; type = "passive"; }; - target: trip-point@1 { + target: trip-point1 { temperature = <75000>; hysteresis = <0>; type = "passive"; @@ -1053,7 +1053,7 @@ "ppmmu3"; clocks = <&media_ctrl HI6220_G3D_CLK>, <&media_ctrl HI6220_G3D_PCLK>; - clock-names = "core", "bus"; + clock-names = "bus", "core"; assigned-clocks = <&media_ctrl HI6220_G3D_CLK>, <&media_ctrl HI6220_G3D_PCLK>; assigned-clock-rates = <500000000>, <144000000>; diff --git a/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi index d456b0aa6f58..77bd8c3a8314 100644 --- a/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi @@ -61,6 +61,153 @@ 0x060 MUX_M1 /* UART6_TXD */ >; }; + + i2c3_pmx_func: i2c3_pmx_func { + pinctrl-single,pins = < + 0x010 MUX_M1 /* I2C3_SCL */ + 0x014 MUX_M1 /* I2C3_SDA */ + >; + }; + + i2c4_pmx_func: i2c4_pmx_func { + pinctrl-single,pins = < + 0x03c MUX_M1 /* I2C4_SCL */ + 0x040 MUX_M1 /* I2C4_SDA */ + >; + }; + + cam0_rst_pmx_func: cam0_rst_pmx_func { + pinctrl-single,pins = < + 0x714 MUX_M0 /* CAM0_RST */ + >; + }; + + cam1_rst_pmx_func: cam1_rst_pmx_func { + pinctrl-single,pins = < + 0x048 MUX_M0 /* CAM1_RST */ + >; + }; + + cam0_pwd_n_pmx_func: cam0_pwd_n_pmx_func { + pinctrl-single,pins = < + 0x098 MUX_M0 /* CAM0_PWD_N */ + >; + }; + + cam1_pwd_n_pmx_func: cam1_pwd_n_pmx_func { + pinctrl-single,pins = < + 0x044 MUX_M0 /* CAM1_PWD_N */ + >; + }; + + isp0_pmx_func: isp0_pmx_func { + pinctrl-single,pins = < + 0x018 MUX_M1 /* ISP_CLK0 */ + 0x024 MUX_M1 /* ISP_SCL0 */ + 0x028 MUX_M1 /* ISP_SDA0 */ + >; + }; + + isp1_pmx_func: isp1_pmx_func { + pinctrl-single,pins = < + 0x01c MUX_M1 /* ISP_CLK1 */ + 0x02c MUX_M1 /* ISP_SCL1 */ + 0x030 MUX_M1 /* ISP_SDA1 */ + >; + }; + }; + + pmx1: pinmux@fff11000 { + compatible = "pinctrl-single"; + reg = <0x0 0xfff11000 0x0 0x73c>; + #gpio-range-cells = <0x3>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 46 0>; + + pwr_key_pmx_func: pwr_key_pmx_func { + pinctrl-single,pins = < + 0x064 MUX_M0 /* GPIO_203 */ + >; + }; + + pd_pmx_func: pd_pmx_func{ + pinctrl-single,pins = < + 0x080 MUX_M0 /* GPIO_221 */ + >; + }; + + i2s2_pmx_func: i2s2_pmx_func { + pinctrl-single,pins = < + 0x050 MUX_M1 /* I2S2_DI */ + 0x054 MUX_M1 /* I2S2_DO */ + 0x058 MUX_M1 /* I2S2_XCLK */ + 0x05c MUX_M1 /* I2S2_XFS */ + >; + }; + + spi0_pmx_func: spi0_pmx_func { + pinctrl-single,pins = < + 0x094 MUX_M1 /* SPI0_CLK */ + 0x098 MUX_M1 /* SPI0_DI */ + 0x09c MUX_M1 /* SPI0_DO */ + 0x0a0 MUX_M1 /* SPI0_CS0_N */ + >; + }; + + spi2_pmx_func: spi2_pmx_func { + pinctrl-single,pins = < + 0x710 MUX_M1 /* SPI2_CLK */ + 0x714 MUX_M1 /* SPI2_DI */ + 0x718 MUX_M1 /* SPI2_DO */ + 0x71c MUX_M1 /* SPI2_CS0_N */ + >; + }; + + spi3_pmx_func: spi3_pmx_func { + pinctrl-single,pins = < + 0x72c MUX_M1 /* SPI3_CLK */ + 0x730 MUX_M1 /* SPI3_DI */ + 0x734 MUX_M1 /* SPI3_DO */ + 0x738 MUX_M1 /* SPI3_CS0_N */ + >; + }; + + i2c0_pmx_func: i2c0_pmx_func { + pinctrl-single,pins = < + 0x020 MUX_M1 /* I2C0_SCL */ + 0x024 MUX_M1 /* I2C0_SDA */ + >; + }; + + i2c1_pmx_func: i2c1_pmx_func { + pinctrl-single,pins = < + 0x028 MUX_M1 /* I2C1_SCL */ + 0x02c MUX_M1 /* I2C1_SDA */ + >; + }; + i2c2_pmx_func: i2c2_pmx_func { + pinctrl-single,pins = < + 0x030 MUX_M1 /* I2C2_SCL */ + 0x034 MUX_M1 /* I2C2_SDA */ + >; + }; + + pcie_clkreq_pmx_func: pcie_clkreq_pmx_func { + pinctrl-single,pins = < + 0x084 MUX_M1 /* PCIE0_CLKREQ_N */ + >; + }; + + gpio185_pmx_func: gpio185_pmx_func { + pinctrl-single,pins = <0x01C 0x1>; + }; + + gpio185_pmx_idle: gpio185_pmx_idle { + pinctrl-single,pins = <0x01C 0x0>; + }; }; pmx2: pinmux@e896c800 { @@ -184,6 +331,180 @@ DRIVE7_02MA DRIVE6_MASK >; }; + + i2c3_cfg_func: i2c3_cfg_func { + pinctrl-single,pins = < + 0x014 0x0 /* I2C3_SCL */ + 0x018 0x0 /* I2C3_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + i2c4_cfg_func: i2c4_cfg_func { + pinctrl-single,pins = < + 0x040 0x0 /* I2C4_SCL */ + 0x044 0x0 /* I2C4_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam0_rst_cfg_func: cam0_rst_cfg_func { + pinctrl-single,pins = < + 0x714 0x0 /* CAM0_RST */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam1_rst_cfg_func: cam1_rst_cfg_func { + pinctrl-single,pins = < + 0x04C 0x0 /* CAM1_RST */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam0_pwd_n_cfg_func: cam0_pwd_n_cfg_func { + pinctrl-single,pins = < + 0x09C 0x0 /* CAM0_PWD_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam1_pwd_n_cfg_func: cam1_pwd_n_cfg_func { + pinctrl-single,pins = < + 0x048 0x0 /* CAM1_PWD_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + isp0_cfg_func: isp0_cfg_func { + pinctrl-single,pins = < + 0x01C 0x0 /* ISP_CLK0 */ + 0x028 0x0 /* ISP_SCL0 */ + 0x02C 0x0 /* ISP_SDA0 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + isp1_cfg_func: isp1_cfg_func { + pinctrl-single,pins = < + 0x020 0x0 /* ISP_CLK1 */ + 0x030 0x0 /* ISP_SCL1 */ + 0x034 0x0 /* ISP_SDA1 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; }; pmx5: pinmux@fc182000 { @@ -338,22 +659,311 @@ }; }; - pmx1: pinmux@fff11000 { - compatible = "pinctrl-single"; - reg = <0x0 0xfff11000 0x0 0x73c>; - #gpio-range-cells = <0x3>; - #pinctrl-cells = <1>; - pinctrl-single,register-width = <0x20>; - pinctrl-single,function-mask = <0x7>; - /* pin base, nr pins & gpio function */ - pinctrl-single,gpio-range = <&range 0 46 0>; - }; - pmx16: pinmux@fff11800 { compatible = "pinconf-single"; reg = <0x0 0xfff11800 0x0 0x73c>; #pinctrl-cells = <1>; pinctrl-single,register-width = <0x20>; + + pwr_key_cfg_func: pwr_key_cfg_func { + pinctrl-single,pins = < + 0x090 0x0 /* GPIO_203 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_02MA DRIVE6_MASK + >; + }; + + usb_cfg_func: usb_cfg_func { + pinctrl-single,pins = < + 0x0AC 0x0 /* GPIO_221 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_02MA DRIVE6_MASK + >; + }; + + spi0_cfg_func: spi0_cfg_func { + pinctrl-single,pins = < + 0x0c8 0x0 /* SPI0_DI */ + 0x0cc 0x0 /* SPI0_DO */ + 0x0d0 0x0 /* SPI0_CS0_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + + spi2_cfg_func: spi2_cfg_func { + pinctrl-single,pins = < + 0x714 0x0 /* SPI2_DI */ + 0x718 0x0 /* SPI2_DO */ + 0x71c 0x0 /* SPI2_CS0_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + + spi3_cfg_func: spi3_cfg_func { + pinctrl-single,pins = < + 0x730 0x0 /* SPI3_DI */ + 0x734 0x0 /* SPI3_DO */ + 0x738 0x0 /* SPI3_CS0_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + + spi0_clk_cfg_func: spi0_clk_cfg_func { + pinctrl-single,pins = < + 0x0c4 0x0 /* SPI0_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_10MA DRIVE6_MASK + >; + }; + + spi2_clk_cfg_func: spi2_clk_cfg_func { + pinctrl-single,pins = < + 0x710 0x0 /* SPI2_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_10MA DRIVE6_MASK + >; + }; + + spi3_clk_cfg_func: spi3_clk_cfg_func { + pinctrl-single,pins = < + 0x72c 0x0 /* SPI3_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_10MA DRIVE6_MASK + >; + }; + + i2c0_cfg_func: i2c0_cfg_func { + pinctrl-single,pins = < + 0x04c 0x0 /* I2C0_SCL */ + 0x050 0x0 /* I2C0_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + i2c1_cfg_func: i2c1_cfg_func { + pinctrl-single,pins = < + 0x054 0x0 /* I2C1_SCL */ + 0x058 0x0 /* I2C1_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + i2c2_cfg_func: i2c2_cfg_func { + pinctrl-single,pins = < + 0x05c 0x0 /* I2C2_SCL */ + 0x060 0x0 /* I2C2_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + pcie_clkreq_cfg_func: pcie_clkreq_cfg_func { + pinctrl-single,pins = < + 0x0b0 0x0 + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + i2s2_cfg_func: i2s2_cfg_func { + pinctrl-single,pins = < + 0x07c 0x0 /* I2S2_DI */ + 0x080 0x0 /* I2S2_DO */ + 0x084 0x0 /* I2S2_XCLK */ + 0x088 0x0 /* I2S2_XFS */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_02MA DRIVE6_MASK + >; + }; + + gpio185_cfg_func: gpio185_cfg_func { + pinctrl-single,pins = <0x048 0>; + pinctrl-single,bias-pulldown = <0 2 0 2>; + pinctrl-single,bias-pullup = <0 1 0 1>; + pinctrl-single,drive-strength = <0x00 0x70>; + pinctrl-single,slew-rate = <0x0 0x80>; + }; + + gpio185_cfg_idle: gpio185_cfg_idle { + pinctrl-single,pins = <0x048 0>; + pinctrl-single,bias-pulldown = <2 2 0 2>; + pinctrl-single,bias-pullup = <0 1 0 1>; + pinctrl-single,drive-strength = <0x00 0x70>; + pinctrl-single,slew-rate = <0x0 0x80>; + }; }; }; }; diff --git a/arch/arm64/boot/dts/hisilicon/hip05.dtsi b/arch/arm64/boot/dts/hisilicon/hip05.dtsi index 405acaa3e9dd..4aed8d440b3a 100644 --- a/arch/arm64/boot/dts/hisilicon/hip05.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip05.dtsi @@ -318,7 +318,7 @@ status = "disabled"; }; - lbc: localbus@80380000 { + lbc: local-bus@80380000 { compatible = "hisilicon,hisi-localbus", "simple-bus"; reg = <0x0 0x80380000 0x0 0x10000>; status = "disabled"; diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi index 7980709e21ff..7deca5f763d5 100644 --- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi @@ -335,7 +335,6 @@ reg = <0x0 0xa0040000 0x0 0x20000>; #iommu-cells = <1>; dma-coherent; - smmu-cb-memtype = <0x0 0x1>; hisilicon,broken-prefetch-cmd; status = "disabled"; }; @@ -737,9 +736,8 @@ #size-cells = <2>; device_type = "pci"; dma-coherent; - ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0 - 0x5ff0000 0x01000000 0 0 0 0xb7ff0000 - 0 0x10000>; + ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0 0x5ff0000>, + <0x01000000 0 0 0 0xb7ff0000 0 0x10000>; #interrupt-cells = <1>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0x0 0 0 1 &mbigen_pcie0 650 4 diff --git a/arch/arm64/boot/dts/hisilicon/hip07.dtsi b/arch/arm64/boot/dts/hisilicon/hip07.dtsi index 7832d9cdec21..2172d8071181 100644 --- a/arch/arm64/boot/dts/hisilicon/hip07.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip07.dtsi @@ -1166,7 +1166,6 @@ reg = <0x0 0xa0040000 0x0 0x20000>; #iommu-cells = <1>; dma-coherent; - smmu-cb-memtype = <0x0 0x1>; hisilicon,broken-prefetch-cmd; status = "disabled"; }; @@ -1181,7 +1180,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; p0_smmu_alg_b: iommu@8d0040000 { compatible = "arm,smmu-v3"; @@ -1194,7 +1192,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; p1_smmu_alg_a: iommu@400d0040000 { compatible = "arm,smmu-v3"; @@ -1207,7 +1204,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; p1_smmu_alg_b: iommu@408d0040000 { compatible = "arm,smmu-v3"; @@ -1220,7 +1216,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; soc { @@ -1708,8 +1703,8 @@ #size-cells = <2>; device_type = "pci"; dma-coherent; - ranges = <0x02000000 0 0xa8000000 0 0xa8000000 0 0x77f0000 - 0x01000000 0 0 0 0xaf7f0000 0 0x10000>; + ranges = <0x02000000 0 0xa8000000 0 0xa8000000 0 0x77f0000>, + <0x01000000 0 0 0 0xaf7f0000 0 0x10000>; #interrupt-cells = <1>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0x0 0 0 1 &mbigen_pcie2_a 671 4 diff --git a/arch/arm64/boot/dts/intel/Makefile b/arch/arm64/boot/dts/intel/Makefile index 296eceec4276..3a052540605b 100644 --- a/arch/arm64/boot/dts/intel/Makefile +++ b/arch/arm64/boot/dts/intel/Makefile @@ -2,3 +2,4 @@ dtb-$(CONFIG_ARCH_AGILEX) += socfpga_agilex_socdk.dtb \ socfpga_agilex_socdk_nand.dtb dtb-$(CONFIG_ARCH_KEEMBAY) += keembay-evm.dtb +dtb-$(CONFIG_ARCH_N5X) += socfpga_n5x_socdk.dtb diff --git a/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts new file mode 100644 index 000000000000..5f56e2697fee --- /dev/null +++ b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts @@ -0,0 +1,53 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021, Intel Corporation + */ +#include "socfpga_agilex.dtsi" + +/ { + model = "eASIC N5X SoCDK"; + + aliases { + serial0 = &uart0; + ethernet0 = &gmac0; + ethernet1 = &gmac1; + ethernet2 = &gmac2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + /* We expect the bootloader to fill in the reg */ + reg = <0 0 0 0>; + }; + + soc { + clocks { + osc1 { + clock-frequency = <25000000>; + }; + }; + }; +}; + +&clkmgr { + compatible = "intel,easic-n5x-clkmgr"; +}; + +&mmc { + status = "okay"; + cap-sd-highspeed; + broken-cd; + bus-width = <4>; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi index daffe136c523..5fc613d24151 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi @@ -67,8 +67,6 @@ /* J6 */ &sata { status = "okay"; - phys = <&comphy2 0>; - phy-names = "sata-phy"; }; /* U11 */ diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts index f5ec3b644769..d239ab70ed99 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts @@ -205,7 +205,7 @@ }; partition@20000 { - label = "u-boot"; + label = "a53-firmware"; reg = <0x20000 0x160000>; }; diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index d5b6c0a1c54a..7a2df148c6a3 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -458,6 +458,8 @@ reg = <0xe0000 0x178>; interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&nb_periph_clk 1>; + phys = <&comphy2 0>; + phy-names = "sata-phy"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-ap807.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi index 623010f3ca89..d9bbbfa4b4eb 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap807.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi @@ -27,3 +27,8 @@ #clock-cells = <1>; }; }; + +&ap_sdhci0 { + compatible = "marvell,armada-ap807-sdhci"; +}; + diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi index 12e477f1aeb9..6614472100c2 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi @@ -281,6 +281,9 @@ gpio-controller; #gpio-cells = <2>; gpio-ranges = <&ap_pinctrl 0 0 20>; + marvell,pwm-offset = <0x10c0>; + #pwm-cells = <2>; + clocks = <&ap_clk 3>; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi index 994a2fce449a..d774a39334d9 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi @@ -234,12 +234,17 @@ gpio-controller; #gpio-cells = <2>; gpio-ranges = <&CP11X_LABEL(pinctrl) 0 0 32>; + marvell,pwm-offset = <0x1f0>; + #pwm-cells = <2>; interrupt-controller; interrupts = <86 IRQ_TYPE_LEVEL_HIGH>, <85 IRQ_TYPE_LEVEL_HIGH>, <84 IRQ_TYPE_LEVEL_HIGH>, <83 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; + clock-names = "core", "axi"; + clocks = <&CP11X_LABEL(clk) 1 21>, + <&CP11X_LABEL(clk) 1 17>; status = "disabled"; }; @@ -250,12 +255,17 @@ gpio-controller; #gpio-cells = <2>; gpio-ranges = <&CP11X_LABEL(pinctrl) 0 32 31>; + marvell,pwm-offset = <0x1f0>; + #pwm-cells = <2>; interrupt-controller; interrupts = <82 IRQ_TYPE_LEVEL_HIGH>, <81 IRQ_TYPE_LEVEL_HIGH>, <80 IRQ_TYPE_LEVEL_HIGH>, <79 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; + clock-names = "core", "axi"; + clocks = <&CP11X_LABEL(clk) 1 21>, + <&CP11X_LABEL(clk) 1 17>; status = "disabled"; }; }; diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index ce49a70d88a0..79020e6d2792 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -113,6 +113,8 @@ &ap_sdhci0 { pinctrl-names = "default"; bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; vqmmc-supply = <&ap0_reg_sd_vccq>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index 18f7b46c4095..deba27ab7657 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt6779.dtsi b/arch/arm64/boot/dts/mediatek/mt6779.dtsi index 370f309d32de..9bdf5145966c 100644 --- a/arch/arm64/boot/dts/mediatek/mt6779.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt6779.dtsi @@ -189,6 +189,23 @@ #clock-cells = <1>; }; + pwrap: pwrap@1000d000 { + compatible = "mediatek,mt6779-pwrap"; + reg = <0 0x1000d000 0 0x1000>; + reg-names = "pwrap"; + interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_PMIC_AP>; + clock-names = "spi", "wrap"; + }; + + devapc: devapc@10207000 { + compatible = "mediatek,mt6779-devapc"; + reg = <0 0x10207000 0 0x1000>; + interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg_ao CLK_INFRA_DEVICE_APC>; + clock-names = "devapc-infra-clock"; + }; + uart0: serial@11002000 { compatible = "mediatek,mt6779-uart", "mediatek,mt6577-uart"; diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index 5b9ec032ce8d..7c6d871538a6 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -698,6 +698,8 @@ clocks = <&pericfg CLK_PERI_MSDC30_1_PD>, <&topckgen CLK_TOP_AXI_SEL>; clock-names = "source", "hclk"; + resets = <&pericfg MT7622_PERI_MSDC1_SW_RST>; + reset-names = "hrst"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts index cba2d8933e79..3249c959f76f 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts @@ -344,6 +344,12 @@ bias-disable; }; }; + + pwm_pins_1: pwm1 { + pins_pwm { + pinmux = <PINMUX_GPIO90__FUNC_PWM_A>; + }; + }; }; &spi0 { @@ -392,3 +398,9 @@ &uart0 { status = "okay"; }; + +&pwm1 { + status = "okay"; + pinctrl-0 = <&pwm_pins_1>; + pinctrl-names = "default"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts new file mode 100644 index 000000000000..fb5ee91b6fe0 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2019 Google LLC + * + * Device-tree for Krane sku0. + * + * SKU is a 8-bit value (0x00 == 0): + * - Bits 7..4: Panel ID: 0x0 (AUO) + * - Bits 3..0: SKU ID: 0x0 (default) + */ + +/dts-v1/; +#include "mt8183-kukui-krane.dtsi" + +/ { + model = "MediaTek krane sku0 board"; + compatible = "google,krane-sku0", "google,krane", "mediatek,mt8183"; +}; + +&panel { + status = "okay"; + compatible = "auo,kd101n80-45na"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts index 47113e275cb5..721d16f9c3b4 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts @@ -16,3 +16,8 @@ model = "MediaTek krane sku176 board"; compatible = "google,krane-sku176", "google,krane", "mediatek,mt8183"; }; + +&panel { + status = "okay"; + compatible = "boe,tv101wum-nl6"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi index bf2ad1294dd3..ff56bcfa3370 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi @@ -249,6 +249,36 @@ proc-supply = <&mt6358_vproc11_reg>; }; +&dsi0 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + panel: panel@0 { + /* compatible will be set in board dts */ + reg = <0>; + enable-gpios = <&pio 45 0>; + pinctrl-names = "default"; + pinctrl-0 = <&panel_pins_default>; + avdd-supply = <&ppvarn_lcd>; + avee-supply = <&ppvarp_lcd>; + pp1800-supply = <&pp1800_lcd>; + backlight = <&backlight_lcd0>; + port { + panel_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; + + ports { + port { + dsi_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; @@ -290,6 +320,10 @@ clock-frequency = <100000>; }; +&mipi_tx0 { + status = "okay"; +}; + &mmc0 { status = "okay"; pinctrl-names = "default", "state_uhs"; @@ -547,6 +581,14 @@ }; }; + panel_pins_default: panel_pins_default { + panel_reset { + pinmux = <PINMUX_GPIO45__FUNC_GPIO45>; + output-low; + bias-pull-up; + }; + }; + pwm0_pin_default: pwm0_pin_default { pins1 { pinmux = <PINMUX_GPIO176__FUNC_GPIO176>; @@ -709,6 +751,10 @@ }; }; +&mfg { + domain-supply = <&mt6358_vgpu_reg>; +}; + &soc_data { status = "okay"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index 5b782a4769e7..80519a145f13 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -6,7 +6,7 @@ */ #include <dt-bindings/clock/mt8183-clk.h> -#include <dt-bindings/gce/mt8173-gce.h> +#include <dt-bindings/gce/mt8183-gce.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/memory/mt8183-larb-port.h> @@ -360,7 +360,7 @@ #size-cells = <0>; #power-domain-cells = <1>; - power-domain@MT8183_POWER_DOMAIN_MFG { + mfg: power-domain@MT8183_POWER_DOMAIN_MFG { reg = <MT8183_POWER_DOMAIN_MFG>; #address-cells = <1>; #size-cells = <0>; @@ -661,12 +661,27 @@ compatible = "mediatek,mt8183-disp-pwm"; reg = <0 0x1100e000 0 0x1000>; interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; #pwm-cells = <2>; clocks = <&topckgen CLK_TOP_MUX_DISP_PWM>, <&infracfg CLK_INFRA_DISP_PWM>; clock-names = "main", "mm"; }; + pwm1: pwm@11006000 { + compatible = "mediatek,mt8183-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&infracfg CLK_INFRA_PWM>, + <&infracfg CLK_INFRA_PWM_HCLK>, + <&infracfg CLK_INFRA_PWM1>, + <&infracfg CLK_INFRA_PWM2>, + <&infracfg CLK_INFRA_PWM3>, + <&infracfg CLK_INFRA_PWM4>; + clock-names = "top", "main", "pwm1", "pwm2", "pwm3", + "pwm4"; + }; + i2c3: i2c@1100f000 { compatible = "mediatek,mt8183-i2c"; reg = <0 0x1100f000 0 0x1000>, @@ -1011,7 +1026,7 @@ clocks = <&mmsys CLK_MM_DISP_RDMA0>; iommus = <&iommu M4U_PORT_DISP_RDMA0>; mediatek,larb = <&larb0>; - mediatek,rdma_fifo_size = <5120>; + mediatek,rdma-fifo-size = <5120>; mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xb000 0x1000>; }; @@ -1023,7 +1038,7 @@ clocks = <&mmsys CLK_MM_DISP_RDMA1>; iommus = <&iommu M4U_PORT_DISP_RDMA1>; mediatek,larb = <&larb0>; - mediatek,rdma_fifo_size = <2048>; + mediatek,rdma-fifo-size = <2048>; mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xc000 0x1000>; }; @@ -1055,8 +1070,7 @@ }; gamma0: gamma@14011000 { - compatible = "mediatek,mt8183-disp-gamma", - "mediatek,mt8173-disp-gamma"; + compatible = "mediatek,mt8183-disp-gamma"; reg = <0 0x14011000 0 0x1000>; interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_LOW>; power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; diff --git a/arch/arm64/boot/dts/mediatek/mt8192.dtsi b/arch/arm64/boot/dts/mediatek/mt8192.dtsi index e12e024de122..9757138a8bbd 100644 --- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi @@ -39,6 +39,7 @@ reg = <0x000>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -49,6 +50,7 @@ reg = <0x100>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -59,6 +61,7 @@ reg = <0x200>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -69,6 +72,7 @@ reg = <0x300>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -79,6 +83,7 @@ reg = <0x400>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -89,6 +94,7 @@ reg = <0x500>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -99,6 +105,7 @@ reg = <0x600>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -109,6 +116,7 @@ reg = <0x700>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -158,6 +166,42 @@ l3_0: l3-cache { compatible = "cache"; }; + + idle-states { + entry-method = "arm,psci"; + cpuoff_l: cpuoff_l { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x00010001>; + local-timer-stop; + entry-latency-us = <55>; + exit-latency-us = <140>; + min-residency-us = <780>; + }; + cpuoff_b: cpuoff_b { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x00010001>; + local-timer-stop; + entry-latency-us = <35>; + exit-latency-us = <145>; + min-residency-us = <720>; + }; + clusteroff_l: clusteroff_l { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x01010002>; + local-timer-stop; + entry-latency-us = <60>; + exit-latency-us = <155>; + min-residency-us = <860>; + }; + clusteroff_b: clusteroff_b { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x01010002>; + local-timer-stop; + entry-latency-us = <40>; + exit-latency-us = <155>; + min-residency-us = <780>; + }; + }; }; pmu-a55 { @@ -379,6 +423,19 @@ status = "disabled"; }; + nor_flash: spi@11234000 { + compatible = "mediatek,mt8192-nor"; + reg = <0 0x11234000 0 0xe0>; + interrupts = <GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&clk26m>, + <&clk26m>, + <&clk26m>; + clock-names = "spi", "sf", "axi"; + #address-cells = <1>; + #size-cells = <0>; + status = "disable"; + }; + i2c3: i2c3@11cb0000 { compatible = "mediatek,mt8192-i2c"; reg = <0 0x11cb0000 0 0x1000>, diff --git a/arch/arm64/boot/dts/mediatek/mt8516.dtsi b/arch/arm64/boot/dts/mediatek/mt8516.dtsi index e6e4d9d60094..b80e95574bef 100644 --- a/arch/arm64/boot/dts/mediatek/mt8516.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8516.dtsi @@ -276,6 +276,27 @@ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; + apdma: dma-controller@11000480 { + compatible = "mediatek,mt8516-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000480 0 0x80>, + <0 0x11000500 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>, + <0 0x11000980 0 0x80>, + <0 0x11000a00 0 0x80>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <6>; + clocks = <&topckgen CLK_TOP_APDMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + uart0: serial@11005000 { compatible = "mediatek,mt8516-uart", "mediatek,mt6577-uart"; @@ -284,6 +305,9 @@ clocks = <&topckgen CLK_TOP_UART0_SEL>, <&topckgen CLK_TOP_UART0>; clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -295,6 +319,9 @@ clocks = <&topckgen CLK_TOP_UART1_SEL>, <&topckgen CLK_TOP_UART1>; clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -306,6 +333,9 @@ clocks = <&topckgen CLK_TOP_UART2_SEL>, <&topckgen CLK_TOP_UART2>; clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/nvidia/Makefile b/arch/arm64/boot/dts/nvidia/Makefile index 9296d12d11e9..e13fb1070472 100644 --- a/arch/arm64/boot/dts/nvidia/Makefile +++ b/arch/arm64/boot/dts/nvidia/Makefile @@ -9,4 +9,5 @@ dtb-$(CONFIG_ARCH_TEGRA_210_SOC) += tegra210-p2894-0050-a08.dtb dtb-$(CONFIG_ARCH_TEGRA_186_SOC) += tegra186-p2771-0000.dtb dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p2972-0000.dtb dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p3509-0000+p3668-0000.dtb +dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p3509-0000+p3668-0001.dtb dtb-$(CONFIG_ARCH_TEGRA_234_SOC) += tegra234-sim-vdk.dtb diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts index 6fd2e0542c27..9f5f5e1fa82e 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts @@ -10,6 +10,725 @@ model = "NVIDIA Jetson TX2 Developer Kit"; compatible = "nvidia,p2771-0000", "nvidia,tegra186"; + aconnect { + status = "okay"; + + dma-controller@2930000 { + status = "okay"; + }; + + interrupt-controller@2a40000 { + status = "okay"; + }; + + ahub@2900800 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + + xbar_admaif0_ep: endpoint { + remote-endpoint = <&admaif0_ep>; + }; + }; + + port@1 { + reg = <0x1>; + + xbar_admaif1_ep: endpoint { + remote-endpoint = <&admaif1_ep>; + }; + }; + + port@2 { + reg = <0x2>; + + xbar_admaif2_ep: endpoint { + remote-endpoint = <&admaif2_ep>; + }; + }; + + port@3 { + reg = <0x3>; + + xbar_admaif3_ep: endpoint { + remote-endpoint = <&admaif3_ep>; + }; + }; + + port@4 { + reg = <0x4>; + + xbar_admaif4_ep: endpoint { + remote-endpoint = <&admaif4_ep>; + }; + }; + + port@5 { + reg = <0x5>; + + xbar_admaif5_ep: endpoint { + remote-endpoint = <&admaif5_ep>; + }; + }; + + port@6 { + reg = <0x6>; + + xbar_admaif6_ep: endpoint { + remote-endpoint = <&admaif6_ep>; + }; + }; + + port@7 { + reg = <0x7>; + + xbar_admaif7_ep: endpoint { + remote-endpoint = <&admaif7_ep>; + }; + }; + + port@8 { + reg = <0x8>; + + xbar_admaif8_ep: endpoint { + remote-endpoint = <&admaif8_ep>; + }; + }; + + port@9 { + reg = <0x9>; + + xbar_admaif9_ep: endpoint { + remote-endpoint = <&admaif9_ep>; + }; + }; + + port@a { + reg = <0xa>; + + xbar_admaif10_ep: endpoint { + remote-endpoint = <&admaif10_ep>; + }; + }; + + port@b { + reg = <0xb>; + + xbar_admaif11_ep: endpoint { + remote-endpoint = <&admaif11_ep>; + }; + }; + + port@c { + reg = <0xc>; + + xbar_admaif12_ep: endpoint { + remote-endpoint = <&admaif12_ep>; + }; + }; + + port@d { + reg = <0xd>; + + xbar_admaif13_ep: endpoint { + remote-endpoint = <&admaif13_ep>; + }; + }; + + port@e { + reg = <0xe>; + + xbar_admaif14_ep: endpoint { + remote-endpoint = <&admaif14_ep>; + }; + }; + + port@f { + reg = <0xf>; + + xbar_admaif15_ep: endpoint { + remote-endpoint = <&admaif15_ep>; + }; + }; + + port@10 { + reg = <0x10>; + + xbar_admaif16_ep: endpoint { + remote-endpoint = <&admaif16_ep>; + }; + }; + + port@11 { + reg = <0x11>; + + xbar_admaif17_ep: endpoint { + remote-endpoint = <&admaif17_ep>; + }; + }; + + port@12 { + reg = <0x12>; + + xbar_admaif18_ep: endpoint { + remote-endpoint = <&admaif18_ep>; + }; + }; + + port@13 { + reg = <0x13>; + + xbar_admaif19_ep: endpoint { + remote-endpoint = <&admaif19_ep>; + }; + }; + + xbar_i2s1_port: port@14 { + reg = <0x14>; + + xbar_i2s1_ep: endpoint { + remote-endpoint = <&i2s1_cif_ep>; + }; + }; + + xbar_i2s2_port: port@15 { + reg = <0x15>; + + xbar_i2s2_ep: endpoint { + remote-endpoint = <&i2s2_cif_ep>; + }; + }; + + xbar_i2s3_port: port@16 { + reg = <0x16>; + + xbar_i2s3_ep: endpoint { + remote-endpoint = <&i2s3_cif_ep>; + }; + }; + + xbar_i2s4_port: port@17 { + reg = <0x17>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_i2s5_port: port@18 { + reg = <0x18>; + + xbar_i2s5_ep: endpoint { + remote-endpoint = <&i2s5_cif_ep>; + }; + }; + + xbar_i2s6_port: port@19 { + reg = <0x19>; + + xbar_i2s6_ep: endpoint { + remote-endpoint = <&i2s6_cif_ep>; + }; + }; + + xbar_dmic1_port: port@1a { + reg = <0x1a>; + + xbar_dmic1_ep: endpoint { + remote-endpoint = <&dmic1_cif_ep>; + }; + }; + + xbar_dmic2_port: port@1b { + reg = <0x1b>; + + xbar_dmic2_ep: endpoint { + remote-endpoint = <&dmic2_cif_ep>; + }; + }; + + xbar_dmic3_port: port@1c { + reg = <0x1c>; + + xbar_dmic3_ep: endpoint { + remote-endpoint = <&dmic3_cif_ep>; + }; + }; + + xbar_dspk1_port: port@1e { + reg = <0x1e>; + + xbar_dspk1_ep: endpoint { + remote-endpoint = <&dspk1_cif_ep>; + }; + }; + + xbar_dspk2_port: port@1f { + reg = <0x1f>; + + xbar_dspk2_ep: endpoint { + remote-endpoint = <&dspk2_cif_ep>; + }; + }; + }; + + admaif@290f000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + admaif0_port: port@0 { + reg = <0x0>; + + admaif0_ep: endpoint { + remote-endpoint = <&xbar_admaif0_ep>; + }; + }; + + admaif1_port: port@1 { + reg = <0x1>; + + admaif1_ep: endpoint { + remote-endpoint = <&xbar_admaif1_ep>; + }; + }; + + admaif2_port: port@2 { + reg = <0x2>; + + admaif2_ep: endpoint { + remote-endpoint = <&xbar_admaif2_ep>; + }; + }; + + admaif3_port: port@3 { + reg = <0x3>; + + admaif3_ep: endpoint { + remote-endpoint = <&xbar_admaif3_ep>; + }; + }; + + admaif4_port: port@4 { + reg = <0x4>; + + admaif4_ep: endpoint { + remote-endpoint = <&xbar_admaif4_ep>; + }; + }; + + admaif5_port: port@5 { + reg = <0x5>; + + admaif5_ep: endpoint { + remote-endpoint = <&xbar_admaif5_ep>; + }; + }; + + admaif6_port: port@6 { + reg = <0x6>; + + admaif6_ep: endpoint { + remote-endpoint = <&xbar_admaif6_ep>; + }; + }; + + admaif7_port: port@7 { + reg = <0x7>; + + admaif7_ep: endpoint { + remote-endpoint = <&xbar_admaif7_ep>; + }; + }; + + admaif8_port: port@8 { + reg = <0x8>; + + admaif8_ep: endpoint { + remote-endpoint = <&xbar_admaif8_ep>; + }; + }; + + admaif9_port: port@9 { + reg = <0x9>; + + admaif9_ep: endpoint { + remote-endpoint = <&xbar_admaif9_ep>; + }; + }; + + admaif10_port: port@a { + reg = <0xa>; + + admaif10_ep: endpoint { + remote-endpoint = <&xbar_admaif10_ep>; + }; + }; + + admaif11_port: port@b { + reg = <0xb>; + + admaif11_ep: endpoint { + remote-endpoint = <&xbar_admaif11_ep>; + }; + }; + + admaif12_port: port@c { + reg = <0xc>; + + admaif12_ep: endpoint { + remote-endpoint = <&xbar_admaif12_ep>; + }; + }; + + admaif13_port: port@d { + reg = <0xd>; + + admaif13_ep: endpoint { + remote-endpoint = <&xbar_admaif13_ep>; + }; + }; + + admaif14_port: port@e { + reg = <0xe>; + + admaif14_ep: endpoint { + remote-endpoint = <&xbar_admaif14_ep>; + }; + }; + + admaif15_port: port@f { + reg = <0xf>; + + admaif15_ep: endpoint { + remote-endpoint = <&xbar_admaif15_ep>; + }; + }; + + admaif16_port: port@10 { + reg = <0x10>; + + admaif16_ep: endpoint { + remote-endpoint = <&xbar_admaif16_ep>; + }; + }; + + admaif17_port: port@11 { + reg = <0x11>; + + admaif17_ep: endpoint { + remote-endpoint = <&xbar_admaif17_ep>; + }; + }; + + admaif18_port: port@12 { + reg = <0x12>; + + admaif18_ep: endpoint { + remote-endpoint = <&xbar_admaif18_ep>; + }; + }; + + admaif19_port: port@13 { + reg = <0x13>; + + admaif19_ep: endpoint { + remote-endpoint = <&xbar_admaif19_ep>; + }; + }; + }; + }; + + i2s@2901000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s1_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s1_ep>; + }; + }; + + i2s1_port: port@1 { + reg = <1>; + + i2s1_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s2_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s2_ep>; + }; + }; + + i2s2_port: port@1 { + reg = <1>; + + i2s2_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s3_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s3_ep>; + }; + }; + + i2s3_port: port@1 { + reg = <1>; + + i2s3_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901400 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s5_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s5_ep>; + }; + }; + + i2s5_port: port@1 { + reg = <1>; + + i2s5_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901500 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s6_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s6_ep>; + }; + }; + + i2s6_port: port@1 { + reg = <1>; + + i2s6_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@2904000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic1_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic1_ep>; + }; + }; + + dmic1_port: port@1 { + reg = <1>; + + dmic1_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dmic@2904100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic2_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic2_ep>; + }; + }; + + dmic2_port: port@1 { + reg = <1>; + + dmic2_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dmic@2904200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic3_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic3_ep>; + }; + }; + + dmic3_port: port@1 { + reg = <1>; + + dmic3_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dspk@2905000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dspk1_cif_ep: endpoint { + remote-endpoint = <&xbar_dspk1_ep>; + }; + }; + + dspk1_port: port@1 { + reg = <1>; + + dspk1_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dspk@2905100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dspk2_cif_ep: endpoint { + remote-endpoint = <&xbar_dspk2_ep>; + }; + }; + + dspk2_port: port@1 { + reg = <1>; + + dspk2_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + }; + }; + i2c@3160000 { power-monitor@42 { compatible = "ti,ina3221"; @@ -369,4 +1088,27 @@ vin-supply = <&vdd_5v0_sys>; }; + + sound { + compatible = "nvidia,tegra186-audio-graph-card"; + status = "okay"; + + dais = /* FE */ + <&admaif0_port>, <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, <&admaif7_port>, + <&admaif8_port>, <&admaif9_port>, <&admaif10_port>, <&admaif11_port>, + <&admaif12_port>, <&admaif13_port>, <&admaif14_port>, <&admaif15_port>, + <&admaif16_port>, <&admaif17_port>, <&admaif18_port>, <&admaif19_port>, + /* Router */ + <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s3_port>, + <&xbar_i2s4_port>, <&xbar_i2s5_port>, <&xbar_i2s6_port>, + <&xbar_dmic1_port>, <&xbar_dmic2_port>, <&xbar_dmic3_port>, + <&xbar_dspk1_port>, <&xbar_dspk2_port>, + /* I/O */ + <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>, + <&i2s5_port>, <&i2s6_port>, <&dmic1_port>, <&dmic2_port>, + <&dmic3_port>, <&dspk1_port>, <&dspk2_port>; + + label = "jetson-tx2-ape"; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi index 58c51965df47..02b26b39cedc 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi @@ -1678,6 +1678,28 @@ interrupt-affinity = <&ca57_0 &ca57_1 &ca57_2 &ca57_3>; }; + sound { + status = "disabled"; + + clocks = <&bpmp TEGRA186_CLK_PLLA>, + <&bpmp TEGRA186_CLK_PLL_A_OUT0>; + clock-names = "pll_a", "plla_out0"; + assigned-clocks = <&bpmp TEGRA186_CLK_PLLA>, + <&bpmp TEGRA186_CLK_PLL_A_OUT0>, + <&bpmp TEGRA186_CLK_AUD_MCLK>; + assigned-clock-parents = <0>, + <&bpmp TEGRA186_CLK_PLLA>, + <&bpmp TEGRA186_CLK_PLL_A_OUT0>; + /* + * PLLA supports dynamic ramp. Below initial rate is chosen + * for this to work and oscillate between base rates required + * for 8x and 11.025x sample rate streams. + */ + assigned-clock-rates = <258000000>; + + iommus = <&smmu TEGRA186_SID_APE>; + }; + thermal-zones { a57 { polling-delay = <0>; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi index d71b7a1140fe..7e7b0eb90c80 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi @@ -93,6 +93,10 @@ vclamp-usb-supply = <&vdd_1v8ao>; ports { + usb2-0 { + vbus-supply = <&vdd_5v0_sys>; + }; + usb2-1 { vbus-supply = <&vdd_5v0_sys>; }; @@ -105,6 +109,10 @@ vbus-supply = <&vdd_5v0_sys>; }; + usb3-2 { + vbus-supply = <&vdd_5v0_sys>; + }; + usb3-3 { vbus-supply = <&vdd_5v0_sys>; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts index 54d057beec59..2888efc42ba1 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts @@ -21,6 +21,513 @@ interrupt-controller@2a40000 { status = "okay"; }; + + ahub@2900800 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + + xbar_admaif0_ep: endpoint { + remote-endpoint = <&admaif0_ep>; + }; + }; + + port@1 { + reg = <0x1>; + + xbar_admaif1_ep: endpoint { + remote-endpoint = <&admaif1_ep>; + }; + }; + + port@2 { + reg = <0x2>; + + xbar_admaif2_ep: endpoint { + remote-endpoint = <&admaif2_ep>; + }; + }; + + port@3 { + reg = <0x3>; + + xbar_admaif3_ep: endpoint { + remote-endpoint = <&admaif3_ep>; + }; + }; + + port@4 { + reg = <0x4>; + + xbar_admaif4_ep: endpoint { + remote-endpoint = <&admaif4_ep>; + }; + }; + + port@5 { + reg = <0x5>; + + xbar_admaif5_ep: endpoint { + remote-endpoint = <&admaif5_ep>; + }; + }; + + port@6 { + reg = <0x6>; + + xbar_admaif6_ep: endpoint { + remote-endpoint = <&admaif6_ep>; + }; + }; + + port@7 { + reg = <0x7>; + + xbar_admaif7_ep: endpoint { + remote-endpoint = <&admaif7_ep>; + }; + }; + + port@8 { + reg = <0x8>; + + xbar_admaif8_ep: endpoint { + remote-endpoint = <&admaif8_ep>; + }; + }; + + port@9 { + reg = <0x9>; + + xbar_admaif9_ep: endpoint { + remote-endpoint = <&admaif9_ep>; + }; + }; + + port@a { + reg = <0xa>; + + xbar_admaif10_ep: endpoint { + remote-endpoint = <&admaif10_ep>; + }; + }; + + port@b { + reg = <0xb>; + + xbar_admaif11_ep: endpoint { + remote-endpoint = <&admaif11_ep>; + }; + }; + + port@c { + reg = <0xc>; + + xbar_admaif12_ep: endpoint { + remote-endpoint = <&admaif12_ep>; + }; + }; + + port@d { + reg = <0xd>; + + xbar_admaif13_ep: endpoint { + remote-endpoint = <&admaif13_ep>; + }; + }; + + port@e { + reg = <0xe>; + + xbar_admaif14_ep: endpoint { + remote-endpoint = <&admaif14_ep>; + }; + }; + + port@f { + reg = <0xf>; + + xbar_admaif15_ep: endpoint { + remote-endpoint = <&admaif15_ep>; + }; + }; + + port@10 { + reg = <0x10>; + + xbar_admaif16_ep: endpoint { + remote-endpoint = <&admaif16_ep>; + }; + }; + + port@11 { + reg = <0x11>; + + xbar_admaif17_ep: endpoint { + remote-endpoint = <&admaif17_ep>; + }; + }; + + port@12 { + reg = <0x12>; + + xbar_admaif18_ep: endpoint { + remote-endpoint = <&admaif18_ep>; + }; + }; + + port@13 { + reg = <0x13>; + + xbar_admaif19_ep: endpoint { + remote-endpoint = <&admaif19_ep>; + }; + }; + + xbar_i2s1_port: port@14 { + reg = <0x14>; + + xbar_i2s1_ep: endpoint { + remote-endpoint = <&i2s1_cif_ep>; + }; + }; + + xbar_i2s2_port: port@15 { + reg = <0x15>; + + xbar_i2s2_ep: endpoint { + remote-endpoint = <&i2s2_cif_ep>; + }; + }; + + xbar_i2s4_port: port@17 { + reg = <0x17>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_i2s6_port: port@19 { + reg = <0x19>; + + xbar_i2s6_ep: endpoint { + remote-endpoint = <&i2s6_cif_ep>; + }; + }; + + xbar_dmic3_port: port@1c { + reg = <0x1c>; + + xbar_dmic3_ep: endpoint { + remote-endpoint = <&dmic3_cif_ep>; + }; + }; + }; + + admaif@290f000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + admaif0_port: port@0 { + reg = <0x0>; + + admaif0_ep: endpoint { + remote-endpoint = <&xbar_admaif0_ep>; + }; + }; + + admaif1_port: port@1 { + reg = <0x1>; + + admaif1_ep: endpoint { + remote-endpoint = <&xbar_admaif1_ep>; + }; + }; + + admaif2_port: port@2 { + reg = <0x2>; + + admaif2_ep: endpoint { + remote-endpoint = <&xbar_admaif2_ep>; + }; + }; + + admaif3_port: port@3 { + reg = <0x3>; + + admaif3_ep: endpoint { + remote-endpoint = <&xbar_admaif3_ep>; + }; + }; + + admaif4_port: port@4 { + reg = <0x4>; + + admaif4_ep: endpoint { + remote-endpoint = <&xbar_admaif4_ep>; + }; + }; + + admaif5_port: port@5 { + reg = <0x5>; + + admaif5_ep: endpoint { + remote-endpoint = <&xbar_admaif5_ep>; + }; + }; + + admaif6_port: port@6 { + reg = <0x6>; + + admaif6_ep: endpoint { + remote-endpoint = <&xbar_admaif6_ep>; + }; + }; + + admaif7_port: port@7 { + reg = <0x7>; + + admaif7_ep: endpoint { + remote-endpoint = <&xbar_admaif7_ep>; + }; + }; + + admaif8_port: port@8 { + reg = <0x8>; + + admaif8_ep: endpoint { + remote-endpoint = <&xbar_admaif8_ep>; + }; + }; + + admaif9_port: port@9 { + reg = <0x9>; + + admaif9_ep: endpoint { + remote-endpoint = <&xbar_admaif9_ep>; + }; + }; + + admaif10_port: port@a { + reg = <0xa>; + + admaif10_ep: endpoint { + remote-endpoint = <&xbar_admaif10_ep>; + }; + }; + + admaif11_port: port@b { + reg = <0xb>; + + admaif11_ep: endpoint { + remote-endpoint = <&xbar_admaif11_ep>; + }; + }; + + admaif12_port: port@c { + reg = <0xc>; + + admaif12_ep: endpoint { + remote-endpoint = <&xbar_admaif12_ep>; + }; + }; + + admaif13_port: port@d { + reg = <0xd>; + + admaif13_ep: endpoint { + remote-endpoint = <&xbar_admaif13_ep>; + }; + }; + + admaif14_port: port@e { + reg = <0xe>; + + admaif14_ep: endpoint { + remote-endpoint = <&xbar_admaif14_ep>; + }; + }; + + admaif15_port: port@f { + reg = <0xf>; + + admaif15_ep: endpoint { + remote-endpoint = <&xbar_admaif15_ep>; + }; + }; + + admaif16_port: port@10 { + reg = <0x10>; + + admaif16_ep: endpoint { + remote-endpoint = <&xbar_admaif16_ep>; + }; + }; + + admaif17_port: port@11 { + reg = <0x11>; + + admaif17_ep: endpoint { + remote-endpoint = <&xbar_admaif17_ep>; + }; + }; + + admaif18_port: port@12 { + reg = <0x12>; + + admaif18_ep: endpoint { + remote-endpoint = <&xbar_admaif18_ep>; + }; + }; + + admaif19_port: port@13 { + reg = <0x13>; + + admaif19_ep: endpoint { + remote-endpoint = <&xbar_admaif19_ep>; + }; + }; + }; + }; + + i2s@2901000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s1_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s1_ep>; + }; + }; + + i2s1_port: port@1 { + reg = <1>; + + i2s1_dap_ep: endpoint { + dai-format = "i2s"; + remote-endpoint = <&rt5658_ep>; + }; + }; + }; + }; + + i2s@2901100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s2_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s2_ep>; + }; + }; + + i2s2_port: port@1 { + reg = <1>; + + i2s2_dap_ep: endpoint { + dai-format = "i2s"; + /* Place holder for external Codec */ + }; + }; + }; + }; + + i2s@2901300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint { + dai-format = "i2s"; + /* Place holder for external Codec */ + }; + }; + }; + }; + + i2s@2901500 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s6_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s6_ep>; + }; + }; + + i2s6_port: port@1 { + reg = <1>; + + i2s6_dap_ep: endpoint@0 { + dai-format = "i2s"; + /* Place holder for external Codec */ + }; + }; + }; + }; + + dmic@2904200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic3_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic3_ep>; + }; + }; + + dmic3_port: port@1 { + reg = <1>; + + dmic3_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + }; }; i2c@3160000 { @@ -57,6 +564,10 @@ pads { usb2 { lanes { + usb2-0 { + status = "okay"; + }; + usb2-1 { status = "okay"; }; @@ -73,6 +584,10 @@ status = "okay"; }; + usb3-2 { + status = "okay"; + }; + usb3-3 { status = "okay"; }; @@ -81,6 +596,11 @@ }; ports { + usb2-0 { + mode = "host"; + status = "okay"; + }; + usb2-1 { mode = "host"; status = "okay"; @@ -96,6 +616,11 @@ status = "okay"; }; + usb3-2 { + nvidia,usb2-companion = <0>; + status = "okay"; + }; + usb3-3 { nvidia,usb2-companion = <3>; maximum-speed = "super-speed"; @@ -107,11 +632,36 @@ usb@3610000 { status = "okay"; - phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, + phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-0}>, + <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-3}>, <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-0}>, + <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-2}>, <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-3}>; - phy-names = "usb2-1", "usb2-3", "usb3-0", "usb3-3"; + phy-names = "usb2-0", "usb2-1", "usb2-3", "usb3-0", "usb3-2", "usb3-3"; + }; + + i2c@c250000 { + status = "okay"; + + rt5658: audio-codec@1a { + status = "okay"; + + compatible = "realtek,rt5658"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA194_MAIN_GPIO(S, 5) GPIO_ACTIVE_HIGH>; + realtek,jd-src = <2>; + sound-name-prefix = "CVB-RT"; + + port { + rt5658_ep: endpoint { + remote-endpoint = <&i2s1_dap_ep>; + mclk-fs = <256>; + clocks = <&bpmp TEGRA194_CLK_AUD_MCLK>; + }; + }; + }; }; pwm@c340000 { @@ -263,6 +813,47 @@ }; }; + sound { + compatible = "nvidia,tegra186-audio-graph-card"; + status = "okay"; + + dais = /* ADMAIF (FE) Ports */ + <&admaif0_port>, <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, <&admaif7_port>, + <&admaif8_port>, <&admaif9_port>, <&admaif10_port>, <&admaif11_port>, + <&admaif12_port>, <&admaif13_port>, <&admaif14_port>, <&admaif15_port>, + <&admaif16_port>, <&admaif17_port>, <&admaif18_port>, <&admaif19_port>, + /* XBAR Ports */ + <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s4_port>, + <&xbar_i2s6_port>, <&xbar_dmic3_port>, + /* BE I/O Ports */ + <&i2s1_port>, <&i2s2_port>, <&i2s4_port>, <&i2s6_port>, + <&dmic3_port>; + + label = "jetson-xavier-ape"; + + widgets = + "Microphone", "CVB-RT MIC Jack", + "Microphone", "CVB-RT MIC", + "Headphone", "CVB-RT HP Jack", + "Speaker", "CVB-RT SPK"; + + routing = + /* I2S1 <-> RT5658 */ + "CVB-RT AIF1 Playback", "I2S1 DAP-Playback", + "I2S1 DAP-Capture", "CVB-RT AIF1 Capture", + /* RT5658 Codec controls */ + "CVB-RT HP Jack", "CVB-RT HPO L Playback", + "CVB-RT HP Jack", "CVB-RT HPO R Playback", + "CVB-RT IN1P", "CVB-RT MIC Jack", + "CVB-RT IN2P", "CVB-RT MIC Jack", + "CVB-RT SPK", "CVB-RT SPO Playback", + "CVB-RT DMIC L1", "CVB-RT MIC", + "CVB-RT DMIC L2", "CVB-RT MIC", + "CVB-RT DMIC R1", "CVB-RT MIC", + "CVB-RT DMIC R2", "CVB-RT MIC"; + }; + thermal-zones { cpu { polling-delay = <0>; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts index 7f97b34216a0..1c3874b677c0 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts @@ -1,345 +1,10 @@ // SPDX-License-Identifier: GPL-2.0 /dts-v1/; -#include <dt-bindings/input/linux-event-codes.h> -#include <dt-bindings/input/gpio-keys.h> - #include "tegra194-p3668-0000.dtsi" +#include "tegra194-p3509-0000.dtsi" / { - model = "NVIDIA Jetson Xavier NX Developer Kit"; + model = "NVIDIA Jetson Xavier NX Developer Kit (SD-card)"; compatible = "nvidia,p3509-0000+p3668-0000", "nvidia,tegra194"; - - bus@0 { - aconnect@2900000 { - status = "okay"; - - dma-controller@2930000 { - status = "okay"; - }; - - interrupt-controller@2a40000 { - status = "okay"; - }; - }; - - ddc: i2c@3190000 { - status = "okay"; - }; - - i2c@3160000 { - eeprom@57 { - compatible = "atmel,24c02"; - reg = <0x57>; - - label = "system"; - vcc-supply = <&vdd_1v8>; - address-width = <8>; - pagesize = <8>; - size = <256>; - read-only; - }; - }; - - hda@3510000 { - nvidia,model = "jetson-xavier-nx-hda"; - status = "okay"; - }; - - padctl@3520000 { - status = "okay"; - - pads { - usb2 { - lanes { - usb2-1 { - status = "okay"; - }; - - usb2-2 { - status = "okay"; - }; - }; - }; - - usb3 { - lanes { - usb3-2 { - status = "okay"; - }; - }; - }; - }; - - ports { - usb2-1 { - mode = "host"; - status = "okay"; - }; - - usb2-2 { - mode = "host"; - vbus-supply = <&vdd_5v0_sys>; - status = "okay"; - }; - - usb3-2 { - nvidia,usb2-companion = <1>; - vbus-supply = <&vdd_5v0_sys>; - status = "okay"; - }; - }; - }; - - usb@3610000 { - status = "okay"; - - phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, - <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-2}>, - <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-2}>; - phy-names = "usb2-1", "usb2-2", "usb3-2"; - }; - - pwm@32d0000 { - status = "okay"; - }; - - host1x@13e00000 { - display-hub@15200000 { - status = "okay"; - }; - - dpaux@155c0000 { - status = "okay"; - }; - - dpaux@155d0000 { - status = "okay"; - }; - - /* DP0 */ - sor@15b00000 { - status = "okay"; - - avdd-io-hdmi-dp-supply = <&vdd_1v0>; - vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; - - nvidia,dpaux = <&dpaux0>; - }; - - /* HDMI */ - sor@15b40000 { - status = "okay"; - - avdd-io-hdmi-dp-supply = <&vdd_1v0>; - vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; - hdmi-supply = <&vdd_hdmi>; - - nvidia,ddc-i2c-bus = <&ddc>; - nvidia,hpd-gpio = <&gpio TEGRA194_MAIN_GPIO(M, 1) - GPIO_ACTIVE_LOW>; - }; - }; - }; - - pcie@14160000 { - status = "okay"; - - vddio-pex-ctl-supply = <&vdd_1v8ao>; - - phys = <&p2u_hsio_11>; - phy-names = "p2u-0"; - }; - - pcie@141a0000 { - status = "okay"; - - vddio-pex-ctl-supply = <&vdd_1v8ao>; - - phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, - <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, - <&p2u_nvhs_6>, <&p2u_nvhs_7>; - - phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", - "p2u-5", "p2u-6", "p2u-7"; - }; - - pcie_ep@141a0000 { - status = "disabled"; - - vddio-pex-ctl-supply = <&vdd_1v8ao>; - - reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; - - nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5) - GPIO_ACTIVE_HIGH>; - - phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, - <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, - <&p2u_nvhs_6>, <&p2u_nvhs_7>; - - phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", - "p2u-5", "p2u-6", "p2u-7"; - }; - - fan: fan { - compatible = "pwm-fan"; - pwms = <&pwm6 0 45334>; - - cooling-levels = <0 64 128 255>; - #cooling-cells = <2>; - }; - - gpio-keys { - compatible = "gpio-keys"; - - force-recovery { - label = "Force Recovery"; - gpios = <&gpio TEGRA194_MAIN_GPIO(G, 0) - GPIO_ACTIVE_LOW>; - linux,input-type = <EV_KEY>; - linux,code = <KEY_SLEEP>; - debounce-interval = <10>; - }; - - power { - label = "Power"; - gpios = <&gpio_aon TEGRA194_AON_GPIO(EE, 4) - GPIO_ACTIVE_LOW>; - linux,input-type = <EV_KEY>; - linux,code = <KEY_POWER>; - debounce-interval = <10>; - wakeup-event-action = <EV_ACT_ASSERTED>; - wakeup-source; - }; - }; - - vdd_5v0_sys: regulator@100 { - compatible = "regulator-fixed"; - regulator-name = "VDD_5V_SYS"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_3v3_sys: regulator@101 { - compatible = "regulator-fixed"; - regulator-name = "VDD_3V3_SYS"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_3v3_ao: regulator@102 { - compatible = "regulator-fixed"; - regulator-name = "VDD_3V3_AO"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8: regulator@103 { - compatible = "regulator-fixed"; - regulator-name = "VDD_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_hdmi: regulator@104 { - compatible = "regulator-fixed"; - regulator-name = "VDD_5V0_HDMI_CON"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - thermal-zones { - cpu { - polling-delay = <0>; - polling-delay-passive = <500>; - status = "okay"; - - trips { - cpu_trip_critical: critical { - temperature = <96500>; - hysteresis = <0>; - type = "critical"; - }; - - cpu_trip_hot: hot { - temperature = <70000>; - hysteresis = <2000>; - type = "hot"; - }; - - cpu_trip_active: active { - temperature = <50000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_passive: passive { - temperature = <30000>; - hysteresis = <2000>; - type = "passive"; - }; - }; - - cooling-maps { - cpu-critical { - cooling-device = <&fan 3 3>; - trip = <&cpu_trip_critical>; - }; - - cpu-hot { - cooling-device = <&fan 2 2>; - trip = <&cpu_trip_hot>; - }; - - cpu-active { - cooling-device = <&fan 1 1>; - trip = <&cpu_trip_active>; - }; - - cpu-passive { - cooling-device = <&fan 0 0>; - trip = <&cpu_trip_passive>; - }; - }; - }; - - gpu { - polling-delay = <0>; - polling-delay-passive = <500>; - status = "okay"; - - trips { - gpu_alert0: critical { - temperature = <99000>; - hysteresis = <0>; - type = "critical"; - }; - }; - }; - - aux { - polling-delay = <0>; - polling-delay-passive = <500>; - status = "okay"; - - trips { - aux_alert0: critical { - temperature = <90000>; - hysteresis = <0>; - type = "critical"; - }; - }; - }; - }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts new file mode 100644 index 000000000000..238fd98e8e45 --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts @@ -0,0 +1,10 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; + +#include "tegra194-p3668-0001.dtsi" +#include "tegra194-p3509-0000.dtsi" + +/ { + model = "NVIDIA Jetson Xavier NX Developer Kit (eMMC)"; + compatible = "nvidia,p3509-0000+p3668-0001", "nvidia,tegra194"; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi new file mode 100644 index 000000000000..d1d77220154f --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi @@ -0,0 +1,351 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/input/gpio-keys.h> + +/ { + bus@0 { + aconnect@2900000 { + status = "okay"; + + dma-controller@2930000 { + status = "okay"; + }; + + interrupt-controller@2a40000 { + status = "okay"; + }; + }; + + ddc: i2c@3190000 { + status = "okay"; + }; + + i2c@3160000 { + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + + label = "system"; + vcc-supply = <&vdd_1v8>; + address-width = <8>; + pagesize = <8>; + size = <256>; + read-only; + }; + }; + + hda@3510000 { + nvidia,model = "jetson-xavier-nx-hda"; + status = "okay"; + }; + + padctl@3520000 { + status = "okay"; + + pads { + usb2 { + lanes { + usb2-1 { + status = "okay"; + }; + + usb2-2 { + status = "okay"; + }; + }; + }; + + usb3 { + lanes { + usb3-2 { + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-1 { + mode = "host"; + status = "okay"; + }; + + usb2-2 { + mode = "host"; + vbus-supply = <&vdd_5v0_sys>; + status = "okay"; + }; + + usb3-2 { + nvidia,usb2-companion = <1>; + vbus-supply = <&vdd_5v0_sys>; + status = "okay"; + }; + }; + }; + + usb@3610000 { + status = "okay"; + + phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, + <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-2}>, + <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-2}>; + phy-names = "usb2-1", "usb2-2", "usb3-2"; + }; + + spi@3270000 { + status = "okay"; + + flash@0 { + compatible = "spi-nor"; + reg = <0>; + spi-max-frequency = <102000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; + }; + + pwm@32d0000 { + status = "okay"; + }; + + host1x@13e00000 { + display-hub@15200000 { + status = "okay"; + }; + + dpaux@155c0000 { + status = "okay"; + }; + + dpaux@155d0000 { + status = "okay"; + }; + + /* DP0 */ + sor@15b00000 { + status = "okay"; + + avdd-io-hdmi-dp-supply = <&vdd_1v0>; + vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; + + nvidia,dpaux = <&dpaux0>; + }; + + /* HDMI */ + sor@15b40000 { + status = "okay"; + + avdd-io-hdmi-dp-supply = <&vdd_1v0>; + vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; + hdmi-supply = <&vdd_hdmi>; + + nvidia,ddc-i2c-bus = <&ddc>; + nvidia,hpd-gpio = <&gpio TEGRA194_MAIN_GPIO(M, 1) + GPIO_ACTIVE_LOW>; + }; + }; + }; + + pcie@14160000 { + status = "okay"; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + phys = <&p2u_hsio_11>; + phy-names = "p2u-0"; + }; + + pcie@141a0000 { + status = "okay"; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, + <&p2u_nvhs_6>, <&p2u_nvhs_7>; + + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", + "p2u-5", "p2u-6", "p2u-7"; + }; + + pcie_ep@141a0000 { + status = "disabled"; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; + + nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5) + GPIO_ACTIVE_HIGH>; + + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, + <&p2u_nvhs_6>, <&p2u_nvhs_7>; + + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", + "p2u-5", "p2u-6", "p2u-7"; + }; + + fan: fan { + compatible = "pwm-fan"; + pwms = <&pwm6 0 45334>; + + cooling-levels = <0 64 128 255>; + #cooling-cells = <2>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + force-recovery { + label = "Force Recovery"; + gpios = <&gpio TEGRA194_MAIN_GPIO(G, 0) + GPIO_ACTIVE_LOW>; + linux,input-type = <EV_KEY>; + linux,code = <KEY_SLEEP>; + debounce-interval = <10>; + }; + + power { + label = "Power"; + gpios = <&gpio_aon TEGRA194_AON_GPIO(EE, 4) + GPIO_ACTIVE_LOW>; + linux,input-type = <EV_KEY>; + linux,code = <KEY_POWER>; + debounce-interval = <10>; + wakeup-event-action = <EV_ACT_ASSERTED>; + wakeup-source; + }; + }; + + vdd_5v0_sys: regulator@100 { + compatible = "regulator-fixed"; + regulator-name = "VDD_5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3_sys: regulator@101 { + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3_ao: regulator@102 { + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3_AO"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8: regulator@103 { + compatible = "regulator-fixed"; + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_hdmi: regulator@104 { + compatible = "regulator-fixed"; + regulator-name = "VDD_5V0_HDMI_CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + thermal-zones { + cpu { + polling-delay = <0>; + polling-delay-passive = <500>; + status = "okay"; + + trips { + cpu_trip_critical: critical { + temperature = <96500>; + hysteresis = <0>; + type = "critical"; + }; + + cpu_trip_hot: hot { + temperature = <70000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpu_trip_active: active { + temperature = <50000>; + hysteresis = <2000>; + type = "active"; + }; + + cpu_trip_passive: passive { + temperature = <30000>; + hysteresis = <2000>; + type = "passive"; + }; + }; + + cooling-maps { + cpu-critical { + cooling-device = <&fan 3 3>; + trip = <&cpu_trip_critical>; + }; + + cpu-hot { + cooling-device = <&fan 2 2>; + trip = <&cpu_trip_hot>; + }; + + cpu-active { + cooling-device = <&fan 1 1>; + trip = <&cpu_trip_active>; + }; + + cpu-passive { + cooling-device = <&fan 0 0>; + trip = <&cpu_trip_passive>; + }; + }; + }; + + gpu { + polling-delay = <0>; + polling-delay-passive = <500>; + status = "okay"; + + trips { + gpu_alert0: critical { + temperature = <99000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + + aux { + polling-delay = <0>; + polling-delay-passive = <500>; + status = "okay"; + + trips { + aux_alert0: critical { + temperature = <90000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi index 0dc8304a2edd..7da3d48cb410 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi @@ -1,79 +1,11 @@ // SPDX-License-Identifier: GPL-2.0 -#include "tegra194.dtsi" - -#include <dt-bindings/mfd/max77620.h> +#include "tegra194-p3668.dtsi" / { - model = "NVIDIA Jetson Xavier NX"; + model = "NVIDIA Jetson Xavier NX (SD-card)"; compatible = "nvidia,p3668-0000", "nvidia,tegra194"; - aliases { - ethernet0 = "/bus@0/ethernet@2490000"; - i2c0 = "/bpmp/i2c"; - i2c1 = "/bus@0/i2c@3160000"; - i2c2 = "/bus@0/i2c@c240000"; - i2c3 = "/bus@0/i2c@3180000"; - i2c4 = "/bus@0/i2c@3190000"; - i2c5 = "/bus@0/i2c@31c0000"; - i2c6 = "/bus@0/i2c@c250000"; - i2c7 = "/bus@0/i2c@31e0000"; - mmc0 = "/bus@0/mmc@3460000"; - rtc0 = "/bpmp/i2c/pmic@3c"; - rtc1 = "/bus@0/rtc@c2a0000"; - serial0 = &tcu; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = "serial0:115200n8"; - }; - bus@0 { - ethernet@2490000 { - status = "okay"; - - phy-reset-gpios = <&gpio TEGRA194_MAIN_GPIO(R, 1) GPIO_ACTIVE_LOW>; - phy-handle = <&phy>; - phy-mode = "rgmii-id"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - phy: phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0x0>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA194_MAIN_GPIO(G, 4) IRQ_TYPE_LEVEL_LOW>; - #phy-cells = <0>; - }; - }; - }; - - memory-controller@2c00000 { - status = "okay"; - }; - - serial@3100000 { - status = "okay"; - }; - - i2c@3160000 { - status = "okay"; - - eeprom@50 { - compatible = "atmel,24c02"; - reg = <0x50>; - - label = "module"; - vcc-supply = <&vdd_1v8ls>; - address-width = <8>; - pagesize = <8>; - size = <256>; - read-only; - }; - }; - /* SDMMC1 (SD/MMC) */ mmc@3400000 { status = "okay"; @@ -82,216 +14,6 @@ disable-wp; vmmc-supply = <&vdd_3v3_sd>; }; - - padctl@3520000 { - avdd-usb-supply = <&vdd_usb_3v3>; - vclamp-usb-supply = <&vdd_1v8ao>; - - ports { - usb2-1 { - vbus-supply = <&vdd_5v0_sys>; - }; - - usb2-3 { - vbus-supply = <&vdd_5v0_sys>; - }; - - usb3-0 { - vbus-supply = <&vdd_5v0_sys>; - }; - - usb3-3 { - vbus-supply = <&vdd_5v0_sys>; - }; - }; - }; - - rtc@c2a0000 { - status = "okay"; - }; - - pmc@c360000 { - nvidia,invert-interrupt; - }; - }; - - bpmp { - i2c { - status = "okay"; - - pmic: pmic@3c { - compatible = "maxim,max20024"; - reg = <0x3c>; - - interrupt-parent = <&pmc>; - interrupts = <24 IRQ_TYPE_LEVEL_LOW>; - #interrupt-cells = <2>; - interrupt-controller; - - #gpio-cells = <2>; - gpio-controller; - - pinctrl-names = "default"; - pinctrl-0 = <&max20024_default>; - - max20024_default: pinmux { - gpio0 { - pins = "gpio0"; - function = "gpio"; - }; - - gpio1 { - pins = "gpio1"; - function = "fps-out"; - maxim,active-fps-source = <MAX77620_FPS_SRC_DEF>; - }; - - gpio2 { - pins = "gpio2"; - function = "fps-out"; - maxim,active-fps-source = <MAX77620_FPS_SRC_DEF>; - }; - - gpio3 { - pins = "gpio3"; - function = "fps-out"; - maxim,active-fps-source = <MAX77620_FPS_SRC_DEF>; - }; - - gpio4 { - pins = "gpio4"; - function = "32k-out1"; - drive-push-pull = <1>; - }; - - gpio6 { - pins = "gpio6"; - function = "gpio"; - drive-push-pull = <1>; - }; - - gpio7 { - pins = "gpio7"; - function = "gpio"; - drive-push-pull = <0>; - }; - }; - - fps { - fps0 { - maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; - maxim,shutdown-fps-time-period-us = <640>; - }; - - fps1 { - maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; - maxim,shutdown-fps-time-period-us = <640>; - maxim,device-state-on-disabled-event = <MAX77620_FPS_INACTIVE_STATE_SLEEP>; - }; - - fps2 { - maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; - maxim,shutdown-fps-time-period-us = <640>; - }; - }; - - regulators { - in-sd0-supply = <&vdd_5v0_sys>; - in-sd1-supply = <&vdd_5v0_sys>; - in-sd2-supply = <&vdd_5v0_sys>; - in-sd3-supply = <&vdd_5v0_sys>; - in-sd4-supply = <&vdd_5v0_sys>; - - in-ldo0-1-supply = <&vdd_5v0_sys>; - in-ldo2-supply = <&vdd_5v0_sys>; - in-ldo3-5-supply = <&vdd_5v0_sys>; - in-ldo4-6-supply = <&vdd_5v0_sys>; - in-ldo7-8-supply = <&vdd_1v8ls>; - - vdd_1v0: sd0 { - regulator-name = "VDDIO_SYS_1V0"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8hs: sd1 { - regulator-name = "VDDIO_SYS_1V8HS"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8ls: sd2 { - regulator-name = "VDDIO_SYS_1V8LS"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8ao: sd3 { - regulator-name = "VDDIO_AO_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - sd4 { - regulator-name = "VDD_DDR_1V1"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo0 { - regulator-name = "VDD_RTC"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo2 { - regulator-name = "VDDIO_AO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo3 { - regulator-name = "VDD_EMMC_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vdd_usb_3v3: ldo5 { - regulator-name = "VDD_USB_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo6 { - regulator-name = "VDD_SDIO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - ldo7 { - regulator-name = "AVDD_CSI_1V2"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - }; - }; - }; - }; }; vdd_3v3_sd: regulator@0 { diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi new file mode 100644 index 000000000000..b7808648cfe4 --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "tegra194-p3668.dtsi" + +/ { + model = "NVIDIA Jetson Xavier NX (eMMC)"; + compatible = "nvidia,p3668-0001", "nvidia,tegra194"; + + bus@0 { + /* SDMMC4 (eMMC) */ + mmc@3460000 { + status = "okay"; + bus-width = <8>; + non-removable; + + vqmmc-supply = <&vdd_1v8ls>; + vmmc-supply = <&vdd_emmc_3v3>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi new file mode 100644 index 000000000000..4f12721c332b --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "tegra194.dtsi" + +#include <dt-bindings/mfd/max77620.h> + +/ { + aliases { + ethernet0 = "/bus@0/ethernet@2490000"; + i2c0 = "/bpmp/i2c"; + i2c1 = "/bus@0/i2c@3160000"; + i2c2 = "/bus@0/i2c@c240000"; + i2c3 = "/bus@0/i2c@3180000"; + i2c4 = "/bus@0/i2c@3190000"; + i2c5 = "/bus@0/i2c@31c0000"; + i2c6 = "/bus@0/i2c@c250000"; + i2c7 = "/bus@0/i2c@31e0000"; + mmc0 = "/bus@0/mmc@3460000"; + rtc0 = "/bpmp/i2c/pmic@3c"; + rtc1 = "/bus@0/rtc@c2a0000"; + serial0 = &tcu; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "serial0:115200n8"; + }; + + bus@0 { + ethernet@2490000 { + status = "okay"; + + phy-reset-gpios = <&gpio TEGRA194_MAIN_GPIO(R, 1) GPIO_ACTIVE_LOW>; + phy-handle = <&phy>; + phy-mode = "rgmii-id"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA194_MAIN_GPIO(G, 4) IRQ_TYPE_LEVEL_LOW>; + #phy-cells = <0>; + }; + }; + }; + + memory-controller@2c00000 { + status = "okay"; + }; + + serial@3100000 { + status = "okay"; + }; + + i2c@3160000 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + + label = "module"; + vcc-supply = <&vdd_1v8ls>; + address-width = <8>; + pagesize = <8>; + size = <256>; + read-only; + }; + }; + + padctl@3520000 { + avdd-usb-supply = <&vdd_usb_3v3>; + vclamp-usb-supply = <&vdd_1v8ao>; + + ports { + usb2-1 { + vbus-supply = <&vdd_5v0_sys>; + }; + + usb2-3 { + vbus-supply = <&vdd_5v0_sys>; + }; + + usb3-0 { + vbus-supply = <&vdd_5v0_sys>; + }; + + usb3-3 { + vbus-supply = <&vdd_5v0_sys>; + }; + }; + }; + + rtc@c2a0000 { + status = "okay"; + }; + + pmc@c360000 { + nvidia,invert-interrupt; + }; + }; + + bpmp { + i2c { + status = "okay"; + + pmic: pmic@3c { + compatible = "maxim,max20024"; + reg = <0x3c>; + + interrupt-parent = <&pmc>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; + #interrupt-cells = <2>; + interrupt-controller; + + #gpio-cells = <2>; + gpio-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&max20024_default>; + + max20024_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_DEF>; + }; + + gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_DEF>; + }; + + gpio3 { + pins = "gpio3"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_DEF>; + }; + + gpio4 { + pins = "gpio4"; + function = "32k-out1"; + drive-push-pull = <1>; + }; + + gpio6 { + pins = "gpio6"; + function = "gpio"; + drive-push-pull = <1>; + }; + + gpio7 { + pins = "gpio7"; + function = "gpio"; + drive-push-pull = <0>; + }; + }; + + fps { + fps0 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + maxim,shutdown-fps-time-period-us = <640>; + }; + + fps1 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; + maxim,shutdown-fps-time-period-us = <640>; + maxim,device-state-on-disabled-event = <MAX77620_FPS_INACTIVE_STATE_SLEEP>; + }; + + fps2 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + maxim,shutdown-fps-time-period-us = <640>; + }; + }; + + regulators { + in-sd0-supply = <&vdd_5v0_sys>; + in-sd1-supply = <&vdd_5v0_sys>; + in-sd2-supply = <&vdd_5v0_sys>; + in-sd3-supply = <&vdd_5v0_sys>; + in-sd4-supply = <&vdd_5v0_sys>; + + in-ldo0-1-supply = <&vdd_5v0_sys>; + in-ldo2-supply = <&vdd_5v0_sys>; + in-ldo3-5-supply = <&vdd_5v0_sys>; + in-ldo4-6-supply = <&vdd_5v0_sys>; + in-ldo7-8-supply = <&vdd_1v8ls>; + + vdd_1v0: sd0 { + regulator-name = "VDDIO_SYS_1V0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8hs: sd1 { + regulator-name = "VDDIO_SYS_1V8HS"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8ls: sd2 { + regulator-name = "VDDIO_SYS_1V8LS"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8ao: sd3 { + regulator-name = "VDDIO_AO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + sd4 { + regulator-name = "VDD_DDR_1V1"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "VDD_RTC"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2 { + regulator-name = "VDDIO_AO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_emmc_3v3: ldo3 { + regulator-name = "VDD_EMMC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_usb_3v3: ldo5 { + regulator-name = "VDD_USB_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6 { + regulator-name = "VDD_SDIO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo7 { + regulator-name = "AVDD_CSI_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + }; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi index 25f36d6118f8..9449156fae39 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi @@ -609,6 +609,34 @@ status = "disabled"; }; + spi@3270000 { + compatible = "nvidia,tegra194-qspi"; + reg = <0x3270000 0x1000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bpmp TEGRA194_CLK_QSPI0>, + <&bpmp TEGRA194_CLK_QSPI0_PM>; + clock-names = "qspi", "qspi_out"; + resets = <&bpmp TEGRA194_RESET_QSPI0>; + reset-names = "qspi"; + status = "disabled"; + }; + + spi@3300000 { + compatible = "nvidia,tegra194-qspi"; + reg = <0x3300000 0x1000>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bpmp TEGRA194_CLK_QSPI1>, + <&bpmp TEGRA194_CLK_QSPI1_PM>; + clock-names = "qspi", "qspi_out"; + resets = <&bpmp TEGRA194_RESET_QSPI1>; + reset-names = "qspi"; + status = "disabled"; + }; + pwm1: pwm@3280000 { compatible = "nvidia,tegra194-pwm", "nvidia,tegra186-pwm"; @@ -2323,6 +2351,26 @@ method = "smc"; }; + sound { + status = "disabled"; + + clocks = <&bpmp TEGRA194_CLK_PLLA>, + <&bpmp TEGRA194_CLK_PLLA_OUT0>; + clock-names = "pll_a", "plla_out0"; + assigned-clocks = <&bpmp TEGRA194_CLK_PLLA>, + <&bpmp TEGRA194_CLK_PLLA_OUT0>, + <&bpmp TEGRA194_CLK_AUD_MCLK>; + assigned-clock-parents = <0>, + <&bpmp TEGRA194_CLK_PLLA>, + <&bpmp TEGRA194_CLK_PLLA_OUT0>; + /* + * PLLA supports dynamic ramp. Below initial rate is chosen + * for this to work and oscillate between base rates required + * for 8x and 11.025x sample rate streams. + */ + assigned-clock-rates = <258000000>; + }; + tcu: tcu { compatible = "nvidia,tegra194-tcu"; mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM TEGRA_HSP_SM_RX(0)>, diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts index 69102dcea8b0..497635af7fab 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts @@ -126,5 +126,304 @@ interrupt-controller@702f9000 { status = "okay"; }; + + ahub@702d0800 { + status = "okay"; + + admaif@702d0000 { + status = "okay"; + }; + + i2s@702d1000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s1_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s1_ep>; + }; + }; + + i2s1_port: port@1 { + reg = <1>; + + i2s1_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s2_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s2_ep>; + }; + }; + + i2s2_port: port@1 { + reg = <1>; + + i2s2_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s3_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s3_ep>; + }; + }; + + i2s3_port: port@1 { + reg = <1>; + + i2s3_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1400 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s5_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s5_ep>; + }; + }; + + i2s5_port: port@1 { + reg = <1>; + + i2s5_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic1_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic1_ep>; + }; + }; + + dmic1_port: port@1 { + reg = <1>; + + dmic1_dap_ep: endpoint { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic2_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic2_ep>; + }; + }; + + dmic2_port: port@1 { + reg = <1>; + + dmic2_dap_ep: endpoint { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic3_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic3_ep>; + }; + }; + + dmic3_port: port@1 { + reg = <1>; + + dmic3_dap_ep: endpoint { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + ports { + xbar_i2s1_port: port@a { + reg = <0xa>; + + xbar_i2s1_ep: endpoint { + remote-endpoint = <&i2s1_cif_ep>; + }; + }; + + xbar_i2s2_port: port@b { + reg = <0xb>; + + xbar_i2s2_ep: endpoint { + remote-endpoint = <&i2s2_cif_ep>; + }; + }; + + xbar_i2s3_port: port@c { + reg = <0xc>; + + xbar_i2s3_ep: endpoint { + remote-endpoint = <&i2s3_cif_ep>; + }; + }; + + xbar_i2s4_port: port@d { + reg = <0xd>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_i2s5_port: port@e { + reg = <0xe>; + + xbar_i2s5_ep: endpoint { + remote-endpoint = <&i2s5_cif_ep>; + }; + }; + + xbar_dmic1_port: port@f { + reg = <0xf>; + + xbar_dmic1_ep: endpoint { + remote-endpoint = <&dmic1_cif_ep>; + }; + }; + + xbar_dmic2_port: port@10 { + reg = <0x10>; + + xbar_dmic2_ep: endpoint { + remote-endpoint = <&dmic2_cif_ep>; + }; + }; + + xbar_dmic3_port: port@11 { + reg = <0x11>; + + xbar_dmic3_ep: endpoint { + remote-endpoint = <&dmic3_cif_ep>; + }; + }; + }; + }; + }; + + sound { + compatible = "nvidia,tegra210-audio-graph-card"; + status = "okay"; + + dais = /* FE */ + <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, + <&admaif7_port>, <&admaif8_port>, <&admaif9_port>, + <&admaif10_port>, + /* Router */ + <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s3_port>, + <&xbar_i2s4_port>, <&xbar_i2s5_port>, <&xbar_dmic1_port>, + <&xbar_dmic2_port>, <&xbar_dmic3_port>, + /* I/O DAP Ports */ + <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>, + <&i2s5_port>, <&dmic1_port>, <&dmic2_port>, <&dmic3_port>; + + label = "jetson-tx1-ape"; }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts index 6a877decffc1..14c128a5e248 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts @@ -636,6 +636,162 @@ interrupt-controller@702f9000 { status = "okay"; }; + + ahub@702d0800 { + status = "okay"; + + admaif@702d0000 { + status = "okay"; + }; + + i2s@702d1200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s3_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s3_ep>; + }; + }; + + i2s3_port: port@1 { + reg = <1>; + + i2s3_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint@0 { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic1_cif_ep: endpoint@0 { + remote-endpoint = <&xbar_dmic1_ep>; + }; + }; + + dmic1_port: port@1 { + reg = <1>; + + dmic1_dap_ep: endpoint@0 { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic2_cif_ep: endpoint@0 { + remote-endpoint = <&xbar_dmic2_ep>; + }; + }; + + dmic2_port: port@1 { + reg = <1>; + + dmic2_dap_ep: endpoint@0 { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + ports { + xbar_i2s3_port: port@c { + reg = <0xc>; + + xbar_i2s3_ep: endpoint { + remote-endpoint = <&i2s3_cif_ep>; + }; + }; + + xbar_i2s4_port: port@d { + reg = <0xd>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_dmic1_port: port@f { + reg = <0xf>; + + xbar_dmic1_ep: endpoint { + remote-endpoint = <&dmic1_cif_ep>; + }; + }; + + xbar_dmic2_port: port@10 { + reg = <0x10>; + + xbar_dmic2_ep: endpoint { + remote-endpoint = <&dmic2_cif_ep>; + }; + }; + }; + }; + }; + + spi@70410000 { + status = "okay"; + + flash@0 { + compatible = "spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; }; clk32k_in: clock@0 { @@ -870,4 +1026,23 @@ vin-supply = <&vdd_5v0_sys>; }; + + sound { + compatible = "nvidia,tegra210-audio-graph-card"; + status = "okay"; + + dais = /* FE */ + <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, + <&admaif7_port>, <&admaif8_port>, <&admaif9_port>, + <&admaif10_port>, + /* Router */ + <&xbar_i2s3_port>, <&xbar_i2s4_port>, + <&xbar_dmic1_port>, <&xbar_dmic2_port>, + /* I/O DAP Ports */ + <&i2s3_port>, <&i2s4_port>, + <&dmic1_port>, <&dmic2_port>; + + label = "jetson-nano-ape"; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index 4fbf8c15b0a1..26b3f98a211c 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -997,6 +997,7 @@ <&tegra_car 128>, /* hda2hdmi */ <&tegra_car 111>; /* hda2codec_2x */ reset-names = "hda", "hda2hdmi", "hda2codec_2x"; + power-domains = <&pd_sor>; status = "disabled"; }; @@ -1043,6 +1044,7 @@ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; resets = <&tegra_car 142>; reset-names = "padctl"; + nvidia,pmc = <&tegra_pmc>; status = "disabled"; @@ -1307,6 +1309,32 @@ status = "disabled"; }; + soctherm: thermal-sensor@700e2000 { + compatible = "nvidia,tegra210-soctherm"; + reg = <0x0 0x700e2000 0x0 0x600>, /* SOC_THERM reg_base */ + <0x0 0x60006000 0x0 0x400>; /* CAR reg_base */ + reg-names = "soctherm-reg", "car-reg"; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "thermal", "edp"; + clocks = <&tegra_car TEGRA210_CLK_TSENSOR>, + <&tegra_car TEGRA210_CLK_SOC_THERM>; + clock-names = "tsensor", "soctherm"; + resets = <&tegra_car 78>; + reset-names = "soctherm"; + #thermal-sensor-cells = <1>; + + throttle-cfgs { + throttle_heavy: heavy { + nvidia,priority = <100>; + nvidia,cpu-throt-percent = <85>; + nvidia,gpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_HIGH>; + + #cooling-cells = <2>; + }; + }; + }; + mipi: mipi@700e3000 { compatible = "nvidia,tegra210-mipi"; reg = <0x0 0x700e3000 0x0 0x100>; @@ -1425,6 +1453,91 @@ "rx9", "tx9", "rx10", "tx10"; status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + admaif1_port: port@0 { + reg = <0>; + + admaif1_ep: endpoint { + remote-endpoint = <&xbar_admaif1_ep>; + }; + }; + + admaif2_port: port@1 { + reg = <1>; + + admaif2_ep: endpoint { + remote-endpoint = <&xbar_admaif2_ep>; + }; + }; + + admaif3_port: port@2 { + reg = <2>; + + admaif3_ep: endpoint { + remote-endpoint = <&xbar_admaif3_ep>; + }; + }; + + admaif4_port: port@3 { + reg = <3>; + + admaif4_ep: endpoint { + remote-endpoint = <&xbar_admaif4_ep>; + }; + }; + + admaif5_port: port@4 { + reg = <4>; + + admaif5_ep: endpoint { + remote-endpoint = <&xbar_admaif5_ep>; + }; + }; + + admaif6_port: port@5 { + reg = <5>; + + admaif6_ep: endpoint { + remote-endpoint = <&xbar_admaif6_ep>; + }; + }; + + admaif7_port: port@6 { + reg = <6>; + + admaif7_ep: endpoint { + remote-endpoint = <&xbar_admaif7_ep>; + }; + }; + + admaif8_port: port@7 { + reg = <7>; + + admaif8_ep: endpoint { + remote-endpoint = <&xbar_admaif8_ep>; + }; + }; + + admaif9_port: port@8 { + reg = <8>; + + admaif9_ep: endpoint { + remote-endpoint = <&xbar_admaif9_ep>; + }; + }; + + admaif10_port: port@9 { + reg = <9>; + + admaif10_ep: endpoint { + remote-endpoint = <&xbar_admaif10_ep>; + }; + }; + }; }; tegra_i2s1: i2s@702d1000 { @@ -1527,6 +1640,89 @@ sound-name-prefix = "DMIC3"; status = "disabled"; }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + + xbar_admaif1_ep: endpoint { + remote-endpoint = <&admaif1_ep>; + }; + }; + + port@1 { + reg = <0x1>; + + xbar_admaif2_ep: endpoint { + remote-endpoint = <&admaif2_ep>; + }; + }; + + port@2 { + reg = <0x2>; + + xbar_admaif3_ep: endpoint { + remote-endpoint = <&admaif3_ep>; + }; + }; + + port@3 { + reg = <0x3>; + + xbar_admaif4_ep: endpoint { + remote-endpoint = <&admaif4_ep>; + }; + }; + + port@4 { + reg = <0x4>; + xbar_admaif5_ep: endpoint { + remote-endpoint = <&admaif5_ep>; + }; + }; + port@5 { + reg = <0x5>; + + xbar_admaif6_ep: endpoint { + remote-endpoint = <&admaif6_ep>; + }; + }; + + port@6 { + reg = <0x6>; + + xbar_admaif7_ep: endpoint { + remote-endpoint = <&admaif7_ep>; + }; + }; + + port@7 { + reg = <0x7>; + + xbar_admaif8_ep: endpoint { + remote-endpoint = <&admaif8_ep>; + }; + }; + + port@8 { + reg = <0x8>; + + xbar_admaif9_ep: endpoint { + remote-endpoint = <&admaif9_ep>; + }; + }; + + port@9 { + reg = <0x9>; + + xbar_admaif10_ep: endpoint { + remote-endpoint = <&admaif10_ep>; + }; + }; + }; }; }; @@ -1536,8 +1732,9 @@ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - clocks = <&tegra_car TEGRA210_CLK_QSPI>; - clock-names = "qspi"; + clocks = <&tegra_car TEGRA210_CLK_QSPI>, + <&tegra_car TEGRA210_CLK_QSPI_PM>; + clock-names = "qspi", "qspi_out"; resets = <&tegra_car 211>; reset-names = "qspi"; dmas = <&apbdma 5>, <&apbdma 5>; @@ -1692,44 +1889,18 @@ &{/cpus/cpu@2} &{/cpus/cpu@3}>; }; - timer { - compatible = "arm,armv8-timer"; - interrupts = <GIC_PPI 13 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; - interrupt-parent = <&gic>; - arm,no-tick-in-suspend; - }; - - soctherm: thermal-sensor@700e2000 { - compatible = "nvidia,tegra210-soctherm"; - reg = <0x0 0x700e2000 0x0 0x600>, /* SOC_THERM reg_base */ - <0x0 0x60006000 0x0 0x400>; /* CAR reg_base */ - reg-names = "soctherm-reg", "car-reg"; - interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "thermal", "edp"; - clocks = <&tegra_car TEGRA210_CLK_TSENSOR>, - <&tegra_car TEGRA210_CLK_SOC_THERM>; - clock-names = "tsensor", "soctherm"; - resets = <&tegra_car 78>; - reset-names = "soctherm"; - #thermal-sensor-cells = <1>; + sound { + status = "disabled"; - throttle-cfgs { - throttle_heavy: heavy { - nvidia,priority = <100>; - nvidia,cpu-throt-percent = <85>; - nvidia,gpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_PLL_A>, + <&tegra_car TEGRA210_CLK_PLL_A_OUT0>; + clock-names = "pll_a", "plla_out0"; - #cooling-cells = <2>; - }; - }; + assigned-clocks = <&tegra_car TEGRA210_CLK_PLL_A>, + <&tegra_car TEGRA210_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA210_CLK_EXTERN1>; + assigned-clock-parents = <0>, <0>, <&tegra_car TEGRA210_CLK_PLL_A_OUT0>; + assigned-clock-rates = <368640000>, <49152000>, <12288000>; }; thermal-zones { @@ -1866,4 +2037,18 @@ }; }; }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + interrupt-parent = <&gic>; + arm,no-tick-in-suspend; + }; }; diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 5113fac80b7a..549a7a2151d4 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -1,19 +1,27 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb -dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-talkman.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-octagon-talkman.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-xiaomi-libra.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb -dtb-$(CONFIG_ARCH_QCOM) += msm8994-msft-lumia-cityman.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-msft-lumia-octagon-cityman.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-ivy.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-karin.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-satsuki.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-sumire.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-suzuran.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb @@ -43,9 +51,12 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 3a9538e1ec97..6aef0c2e4f0a 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -301,6 +301,10 @@ status = "okay"; }; +&mdss { + status = "okay"; +}; + &pm8916_resin { status = "okay"; linux,code = <KEY_VOLUMEDOWN>; diff --git a/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts new file mode 100644 index 000000000000..a8dffc8c64ea --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +/* As the names may imply, there is quite a bunch of duplication there. */ +#include "msm8994-sony-xperia-kitakami-karin.dts" + +/ { + model = "Sony Xperia Z4 Tablet (Wi-Fi)"; + compatible = "sony,karin_windy", "qcom,apq8094"; + + /* + * This model uses the APQ variant of MSM8994 (APQ8094). + * The v1/v2/v2.1 story (from kitakami.dtsi) also applies here. + */ + qcom,msm-id = <253 0x20000>, <253 0x20001>; +}; + +/delete-node/ &pm8994_l1; +/delete-node/ &pm8994_l19; diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts new file mode 100644 index 000000000000..540b1fa4b260 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts @@ -0,0 +1,291 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Alcatel OneTouch Idol 3 (4.7)"; + compatible = "alcatel,idol347", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 69 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&blsp_i2c5 { + status = "okay"; + + magnetometer@c { + compatible = "asahi-kasei,ak09911"; + reg = <0x0c>; + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + reset-gpios = <&msmgpio 8 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; + + accelerometer@f { + compatible = "kionix,kxtj21009"; + reg = <0x0f>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + interrupt-parent = <&msmgpio>; + interrupts = <31 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_int_default>; + mount-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + }; + + proximity@48 { + compatible = "sensortek,stk3310"; + reg = <0x48>; + interrupt-parent = <&msmgpio>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&proximity_int_default>; + }; + + gyroscope@68 { + compatible = "bosch,bmg160"; + reg = <0x68>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + interrupt-parent = <&msmgpio>; + interrupts = <97 IRQ_TYPE_EDGE_RISING>, + <98 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_int_default>; + }; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + accel_int_default: accel-int-default { + pins = "gpio31"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gyro_int_default: gyro-int-default { + pins = "gpio97", "gpio98"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + mag_reset_default: mag-reset-default { + pins = "gpio8"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + proximity_int_default: proximity-int-default { + pins = "gpio12"; + function = "gpio"; + + drive-strength = <6>; + bias-pull-up; + }; + + usb_id_default: usb-id-default { + pins = "gpio69"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts new file mode 100644 index 000000000000..cee451e59385 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts @@ -0,0 +1,195 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Asus Zenfone 2 Laser"; + compatible = "asus,z00l", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&msmgpio 117 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + debounce-interval = <15>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&msmgpio 110 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + gpio_keys_default: gpio-keys-default { + pins = "gpio107", "gpio117"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + usb_id_default: usb-id-default { + pins = "gpio110"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts new file mode 100644 index 000000000000..27845189ac2b --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts @@ -0,0 +1,267 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "BQ Aquaris X5 (Longcheer L8910)"; + compatible = "longcheer,l8910", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + gpios = <&msmgpio 17 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_WHITE>; + default-state = "off"; + function = LED_FUNCTION_KBD_BACKLIGHT; + + pinctrl-names = "default"; + pinctrl-0 = <&button_backlight_default>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp_i2c3 { + status = "okay"; + + magnetometer@d { + compatible = "asahi-kasei,ak09911"; + reg = <0x0d>; + + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + + reset-gpios = <&msmgpio 111 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + }; + + imu@68 { + compatible = "bosch,bmi160"; + reg = <0x68>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + button_backlight_default: button-backlight-default { + pins = "gpio17"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + mag_reset_default: mag-reset-default { + pins = "gpio111"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + usb_id_default: usb-id-default { + pins = "gpio110"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi index 4dc437f13fa5..7dedb91b9930 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi @@ -220,6 +220,22 @@ bias-disable; }; + i2c3_default: i2c3-default { + pins = "gpio10", "gpio11"; + function = "blsp_i2c3"; + + drive-strength = <2>; + bias-disable; + }; + + i2c3_sleep: i2c3-sleep { + pins = "gpio10", "gpio11"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + i2c4_default: i2c4-default { pins = "gpio14", "gpio15"; function = "blsp_i2c4"; diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi index f91269492d72..230ba3ce3277 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi @@ -106,6 +106,9 @@ interrupt-parent = <&msmgpio>; interrupts = <115 IRQ_TYPE_EDGE_RISING>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + pinctrl-names = "default"; pinctrl-0 = <&accel_int_default>; }; @@ -113,6 +116,9 @@ magnetometer@12 { compatible = "bosch,bmc150_magn"; reg = <0x12>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; }; }; @@ -126,6 +132,10 @@ pinctrl-1 = <&mdss_sleep>; }; +&mdss { + status = "okay"; +}; + &pm8916_resin { status = "okay"; linux,code = <KEY_VOLUMEDOWN>; diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts index e39c04d977c2..dd35c3344358 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts @@ -38,7 +38,7 @@ &pronto { iris { - compatible = "qcom,wcn3680"; + compatible = "qcom,wcn3660b"; }; }; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 402e891a84ab..5353da521974 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -56,7 +56,7 @@ no-map; }; - reserved@8668000 { + reserved@86680000 { reg = <0x0 0x86680000 0x0 0x80000>; no-map; }; @@ -69,7 +69,7 @@ qcom,client-id = <1>; }; - rfsa@867e00000 { + rfsa@867e0000 { reg = <0x0 0x867e0000 0x0 0x20000>; no-map; }; @@ -913,6 +913,7 @@ }; mdss: mdss@1a00000 { + status = "disabled"; compatible = "qcom,mdss"; reg = <0x01a00000 0x1000>, <0x01ac8000 0x3000>; @@ -1528,6 +1529,21 @@ status = "disabled"; }; + blsp_i2c3: i2c@78b7000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b7000 0x500>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c3_default>; + pinctrl-1 = <&i2c3_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + blsp_spi3: spi@78b7000 { compatible = "qcom,spi-qup-v2.2.1"; reg = <0x078b7000 0x500>; diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts index 5969b5cfdc85..23cdcc9f7c72 100644 --- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts +++ b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts @@ -6,6 +6,8 @@ /dts-v1/; #include "msm8992.dtsi" +#include "pm8994.dtsi" +#include "pmi8994.dtsi" / { model = "LG Nexus 5X"; @@ -44,7 +46,7 @@ }; &rpm_requests { - pm8994-regulators { + pm8994_regulators: pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; vdd_l1-supply = <&pm8994_s1>; @@ -53,15 +55,17 @@ vdd_l4_27_31-supply = <&pm8994_s3>; vdd_l5_7-supply = <&pm8994_s3>; vdd_l6_12_32-supply = <&pm8994_s5>; - vdd_l8_16_30-supply = <&vreg_vph_pwr>; - vdd_l9_10_18_22-supply = <&vreg_vph_pwr>; - vdd_l13_19_23_24-supply = <&vreg_vph_pwr>; + vdd_l8_16_30-supply = <&vph_pwr>; + vdd_l9_10_18_22-supply = <&vph_pwr>; + vdd_l13_19_23_24-supply = <&vph_pwr>; vdd_l14_15-supply = <&pm8994_s5>; - vdd_l17_29-supply = <&vreg_vph_pwr>; - vdd_l20_21-supply = <&vreg_vph_pwr>; + vdd_l17_29-supply = <&vph_pwr>; + vdd_l20_21-supply = <&vph_pwr>; vdd_l25-supply = <&pm8994_s5>; vdd_lvs1_2 = <&pm8994_s4>; + /* S1, S2, S6 and S12 are managed by RPMPD */ + pm8994_s1: s1 { regulator-min-microvolt = <800000>; regulator-max-microvolt = <800000>; @@ -93,6 +97,8 @@ regulator-max-microvolt = <1000000>; }; + /* S8, S9, S10 and S11 - SPMI-managed VDD_APC */ + pm8994_l1: l1 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -113,18 +119,14 @@ regulator-max-microvolt = <1225000>; }; - pm8994_l5: l5 { - /* TODO */ - }; + /* L5 is inaccessible from RPM */ pm8994_l6: l6 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - pm8994_l7: l7 { - /* TODO */ - }; + /* L7 is inaccessible from RPM */ pm8994_l8: l8 { regulator-min-microvolt = <1800000>; @@ -266,9 +268,22 @@ */ }; }; + + pmi8994_regulators: pmi8994-regulators { + compatible = "qcom,rpm-pmi8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + pmi8994_s1: s1 {}; + + /* S2 & S3 - VDD_GFX */ + + pmi8994_bby: boost-bypass {}; + }; }; -&sdhc_1 { +&sdhc1 { status = "okay"; mmc-hs400-1_8v; diff --git a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts new file mode 100644 index 000000000000..5322b9ce5839 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + * Copyright (c) 2020, Gustave Monce <gustave.monce@outlook.com> + */ + +/dts-v1/; + +#include "msm8992.dtsi" +#include "msm8994-msft-lumia-octagon.dtsi" + +/ { + model = "Microsoft Lumia 950"; + compatible = "microsoft,talkman", "qcom,msm8992"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts deleted file mode 100644 index c337a86a5c77..000000000000 --- a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts +++ /dev/null @@ -1,67 +0,0 @@ -// SPDX-License-Identifier: BSD-3-Clause -/* - * Copyright (c) 2020, Konrad Dybcio - */ - -/dts-v1/; - -#include "msm8992.dtsi" -#include "pm8994.dtsi" -#include "pmi8994.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/gpio-keys.h> - -/ { - model = "Microsoft Lumia 950"; - compatible = "microsoft,talkman", "qcom,msm8992"; - - /* Most Lumia 950 users use GRUB to load their kernels, - * hence there is no need for msm-id and friends. - */ - - /* This enables graphical output via bootloader-enabled display. - * acpi=no is required due to WP platforms having ACPI support, but - * only for Windows-based OSes. - */ - chosen { - bootargs = "earlycon=efifb console=efifb acpi=no"; - - #address-cells = <2>; - #size-cells = <2>; - ranges; - }; -}; - -&blsp_i2c1 { - status = "okay"; - - rmi4-i2c-dev@4b { - compatible = "syna,rmi4-i2c"; - reg = <0x4b>; - #address-cells = <1>; - #size-cells = <0>; - - interrupt-parent = <&tlmm>; - interrupts = <77 IRQ_TYPE_EDGE_FALLING>; - - rmi4-f01@1 { - reg = <0x01>; - syna,nosleep-mode = <1>; - }; - - rmi4-f12@12 { - reg = <0x12>; - syna,sensor-type = <1>; - syna,clip-x-low = <0>; - syna,clip-x-high = <1440>; - syna,clip-y-low = <0>; - syna,clip-y-high = <2560>; - }; - }; -}; - -&sdhc_1 { - status = "okay"; - - mmc-hs200-1_8v; -}; diff --git a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts index 4f64ca3ea1ef..357d55496e75 100644 --- a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts +++ b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts @@ -70,21 +70,6 @@ pmsg-size = <0x20000>; }; - continuous_splash: framebuffer@3401000{ - reg = <0x0 0x3401000 0x0 0x2200000>; - no-map; - }; - - dfps_data_mem: dfps_data_mem@3400000 { - reg = <0x0 0x3400000 0x0 0x1000>; - no-map; - }; - - peripheral_region: peripheral_region@7400000 { - reg = <0x0 0x7400000 0x0 0x1c00000>; - no-map; - }; - modem_region: modem_region@9000000 { reg = <0x0 0x9000000 0x0 0x5a00000>; no-map; @@ -97,43 +82,49 @@ }; }; -&blsp_i2c2 { +&blsp1_i2c2 { status = "okay"; /* Atmel or Synaptics touchscreen */ }; -&blsp_i2c5 { +&blsp1_i2c5 { status = "okay"; - /* Silabs si4705 FM transmitter */ + /* ST lsm6db0 gyro/accelerometer */ }; -&blsp_i2c6 { +&blsp1_i2c6 { status = "okay"; - /* NCI NFC, + /* + * NXP NCI NFC, * TI USB320 Type-C controller, * Pericom 30216a USB (de)mux switch */ }; -&blsp_i2c7 { +&blsp2_i2c1 { status = "okay"; /* cm36686 proximity and ambient light sensor */ }; -&blsp_i2c13 { +&blsp2_i2c5 { status = "okay"; - /* ST lsm6db0 gyro/accelerometer */ + /* Silabs si4705 FM transmitter */ }; &blsp2_uart2 { status = "okay"; }; +&peripheral_region { + reg = <0x0 0x7400000 0x0 0x1c00000>; + no-map; +}; + &rpm_requests { pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; @@ -144,24 +135,16 @@ vdd_l4_27_31-supply = <&pm8994_s3>; vdd_l5_7-supply = <&pm8994_s3>; vdd_l6_12_32-supply = <&pm8994_s5>; - vdd_l8_16_30-supply = <&vreg_vph_pwr>; - vdd_l9_10_18_22-supply = <&vreg_vph_pwr>; - vdd_l13_19_23_24-supply = <&vreg_vph_pwr>; + vdd_l8_16_30-supply = <&vph_pwr>; + vdd_l9_10_18_22-supply = <&vph_pwr>; + vdd_l13_19_23_24-supply = <&vph_pwr>; vdd_l14_15-supply = <&pm8994_s5>; - vdd_l17_29-supply = <&vreg_vph_pwr>; - vdd_l20_21-supply = <&vreg_vph_pwr>; + vdd_l17_29-supply = <&vph_pwr>; + vdd_l20_21-supply = <&vph_pwr>; vdd_l25-supply = <&pm8994_s5>; vdd_lvs1_2 = <&pm8994_s4>; - pm8994_s1: s1 { - /* unused */ - status = "disabled"; - }; - - pm8994_s2: s2 { - /* unused */ - status = "disabled"; - }; + /* S1, S2, S6 and S12 are managed by RPMPD */ pm8994_s3: s3 { regulator-min-microvolt = <1300000>; @@ -186,6 +169,8 @@ regulator-max-microvolt = <1000000>; }; + /* S8, S9, S10 and S11 - SPMI-managed VDD_APC */ + pm8994_l1: l1 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -206,20 +191,14 @@ regulator-max-microvolt = <1225000>; }; - pm8994_l5: l5 { - /* unused */ - status = "disabled"; - }; + /* L5 is inaccessible from RPM */ pm8994_l6: l6 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - pm8994_l7: l7 { - /* unused */ - status = "disabled"; - }; + /* L7 is inaccessible from RPM */ pm8994_l8: l8 { regulator-min-microvolt = <1800000>; @@ -352,10 +331,31 @@ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; + + pm8994_lvs1: lvs1 {}; + pm8994_lvs2: lvs2 {}; + }; + + pmi8994_regulators: pmi8994-regulators { + compatible = "qcom,rpm-pmi8994-regulators"; + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + pmi8994_s1: s1 { + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + + /* S2 & S3 - VDD_GFX */ + + pmi8994_bby: boost-bypass { + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3600000>; + }; }; }; -&sdhc_1 { +&sdhc1 { status = "okay"; mmc-hs400-1_8v; diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi index 0c422af47917..58fe58cc7703 100644 --- a/arch/arm64/boot/dts/qcom/msm8992.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi @@ -2,738 +2,29 @@ /* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved. */ -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/clock/qcom,gcc-msm8994.h> +#include "msm8994.dtsi" -/ { - interrupt-parent = <&intc>; +/* 8992 only features 2 A57 cores. */ +/delete-node/ &CPU6; +/delete-node/ &CPU7; +/delete-node/ &cpu6_map; +/delete-node/ &cpu7_map; - #address-cells = <2>; - #size-cells = <2>; - - chosen { }; - - cpus { - #address-cells = <2>; - #size-cells = <0>; - - CPU0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x0>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - L2_0: l2-cache { - compatible = "cache"; - cache-level = <2>; - }; - }; - - CPU1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x1>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - }; - - CPU2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x2>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - }; - - CPU3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x3>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - }; - - CPU4: cpu@100 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x100>; - next-level-cache = <&L2_1>; - enable-method = "psci"; - L2_1: l2-cache { - compatible = "cache"; - cache-level = <2>; - }; - }; - - CPU5: cpu@101 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x101>; - next-level-cache = <&L2_1>; - enable-method = "psci"; - }; - - cpu-map { - cluster0 { - core0 { - cpu = <&CPU0>; - }; - - core1 { - cpu = <&CPU1>; - }; - - core2 { - cpu = <&CPU2>; - }; - - core3 { - cpu = <&CPU3>; - }; - }; - - cluster1 { - core0 { - cpu = <&CPU4>; - }; - - core1 { - cpu = <&CPU5>; - }; - }; - }; - }; - - clocks { - xo_board: xo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <19200000>; - }; - - sleep_clk: sleep_clk { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32768>; - }; - }; - - firmware { - scm { - compatible = "qcom,scm-msm8994", "qcom,scm"; - }; - }; - - memory { - device_type = "memory"; - /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; - }; - - pmu { - compatible = "arm,cortex-a53-pmu"; - interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4)| IRQ_TYPE_LEVEL_HIGH)>; - }; - - psci { - compatible = "arm,psci-0.2"; - method = "hvc"; - }; - - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - smem_region: smem@6a00000 { - reg = <0x0 0x6a00000 0x0 0x200000>; - no-map; - }; - }; - - sfpb_mutex: hwmutex { - compatible = "qcom,sfpb-mutex"; - syscon = <&sfpb_mutex_regs 0x0 0x100>; - #hwlock-cells = <1>; - }; - - smem { - compatible = "qcom,smem"; - memory-region = <&smem_region>; - qcom,rpm-msg-ram = <&rpm_msg_ram>; - hwlocks = <&sfpb_mutex 3>; - }; - - soc { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0xffffffff>; - compatible = "simple-bus"; - - intc: interrupt-controller@f9000000 { - compatible = "qcom,msm-qgic2"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0xf9000000 0x1000>, - <0xf9002000 0x1000>; - }; - - apcs: mailbox@f900d000 { - compatible = "qcom,msm8994-apcs-kpss-global", "syscon"; - reg = <0xf900d000 0x2000>; - #mbox-cells = <1>; - }; - - timer@f9020000 { - #address-cells = <1>; - #size-cells = <1>; - ranges; - compatible = "arm,armv7-timer-mem"; - reg = <0xf9020000 0x1000>; - - frame@f9021000 { - frame-number = <0>; - interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9021000 0x1000>, - <0xf9022000 0x1000>; - }; - - frame@f9023000 { - frame-number = <1>; - interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9023000 0x1000>; - status = "disabled"; - }; - - frame@f9024000 { - frame-number = <2>; - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9024000 0x1000>; - status = "disabled"; - }; - - frame@f9025000 { - frame-number = <3>; - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9025000 0x1000>; - status = "disabled"; - }; - - frame@f9026000 { - frame-number = <4>; - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9026000 0x1000>; - status = "disabled"; - }; - - frame@f9027000 { - frame-number = <5>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9027000 0x1000>; - status = "disabled"; - }; - - frame@f9028000 { - frame-number = <6>; - interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xf9028000 0x1000>; - status = "disabled"; - }; - }; - - usb3: usb@f92f8800 { - compatible = "qcom,msm8996-dwc3", "qcom,dwc3"; - reg = <0xf92f8800 0x400>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - clocks = <&gcc GCC_USB30_MASTER_CLK>, - <&gcc GCC_SYS_NOC_USB3_AXI_CLK>, - <&gcc GCC_USB30_SLEEP_CLK>, - <&gcc GCC_USB30_MOCK_UTMI_CLK>; - clock-names = "core", "iface", "sleep", "mock_utmi", "ref", "xo"; - - assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, - <&gcc GCC_USB30_MASTER_CLK>; - assigned-clock-rates = <19200000>, <120000000>; - - power-domains = <&gcc USB30_GDSC>; - qcom,select-utmi-as-pipe-clk; - - dwc3@f9200000 { - compatible = "snps,dwc3"; - reg = <0xf9200000 0xcc00>; - interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>; - snps,dis_u2_susphy_quirk; - snps,dis_enblslpm_quirk; - maximum-speed = "high-speed"; - dr_mode = "peripheral"; - }; - }; - - sdhc_1: sdhci@f9824900 { - compatible = "qcom,sdhci-msm-v4"; - reg = <0xf9824900 0x1a0>, <0xf9824000 0x800>; - reg-names = "hc_mem", "core_mem"; - - interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "hc_irq", "pwr_irq"; - - clocks = <&gcc GCC_SDCC1_APPS_CLK>, - <&gcc GCC_SDCC1_AHB_CLK>, - <&xo_board>; - clock-names = "core", "iface", "xo"; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on - &sdc1_rclk_on>; - pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off - &sdc1_rclk_off>; - - regulator-always-on; - bus-width = <8>; - non-removable; - - status = "disabled"; - }; - - sdhc_2: sdhci@f98a4900 { - compatible = "qcom,sdhci-msm-v4"; - reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>; - reg-names = "hc_mem", "core_mem"; - - interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "hc_irq", "pwr_irq"; - - clocks = <&gcc GCC_SDCC2_APPS_CLK>, - <&gcc GCC_SDCC2_AHB_CLK>, - <&xo_board>; - clock-names = "core", "iface", "xo"; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; - pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; - - cd-gpios = <&tlmm 100 0>; - bus-width = <4>; - status = "disabled"; - }; - - blsp1_uart2: serial@f991e000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0xf991e000 0x1000>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_LOW>; - clock-names = "core", "iface"; - clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp1_uart2_default>; - pinctrl-1 = <&blsp1_uart2_sleep>; - status = "disabled"; - }; - - blsp_i2c1: i2c@f9923000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9923000 0x500>; - interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c1_default>; - pinctrl-1 = <&i2c1_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp_i2c2: i2c@f9924000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9924000 0x500>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c2_default>; - pinctrl-1 = <&i2c2_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - /* Somebody was very creative with their numbering scheme downstream... */ - - blsp_i2c13: i2c@f9927000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9927000 0x500>; - interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c13_default>; - pinctrl-1 = <&i2c13_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp_i2c6: i2c@f9928000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9928000 0x500>; - interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c6_default>; - pinctrl-1 = <&i2c6_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp2_uart2: serial@f995e000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0xf995e000 0x1000>; - interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_LOW>; - clock-names = "core", "iface"; - clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, - <&gcc GCC_BLSP2_AHB_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp2_uart2_default>; - pinctrl-1 = <&blsp2_uart2_sleep>; - status = "disabled"; - }; - - blsp_i2c7: i2c@f9963000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9963000 0x500>; - interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP2_AHB_CLK>, - <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c7_default>; - pinctrl-1 = <&i2c7_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp_i2c5: i2c@f9967000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9967000 0x500>; - interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP2_AHB_CLK>, - <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <100000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c5_default>; - pinctrl-1 = <&i2c5_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - gcc: clock-controller@fc400000 { - compatible = "qcom,gcc-msm8994"; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - reg = <0xfc400000 0x2000>; - }; - - rpm_msg_ram: memory@fc428000 { - compatible = "qcom,rpm-msg-ram"; - reg = <0xfc428000 0x4000>; - }; - - restart@fc4ab000 { - compatible = "qcom,pshold"; - reg = <0xfc4ab000 0x4>; - }; - - spmi_bus: spmi@fc4c0000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0xfc4cf000 0x1000>, - <0xfc4cb000 0x1000>, - <0xfc4ca000 0x1000>; - reg-names = "core", "intr", "cnfg"; - interrupt-names = "periph_irq"; - interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; - qcom,ee = <0>; - qcom,channel = <0>; - #address-cells = <2>; - #size-cells = <0>; - interrupt-controller; - #interrupt-cells = <4>; - }; - - sfpb_mutex_regs: syscon@fd484000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "syscon"; - reg = <0xfd484000 0x400>; - }; - - tlmm: pinctrl@fd510000 { - compatible = "qcom,msm8994-pinctrl"; - reg = <0xfd510000 0x4000>; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - gpio-ranges = <&tlmm 0 0 146>; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - - blsp1_uart2_default: blsp1-uart2-default { - function = "blsp_uart2"; - pins = "gpio4", "gpio5"; - drive-strength = <16>; - bias-disable; - }; - - blsp1_uart2_sleep: blsp1-uart2-sleep { - function = "gpio"; - pins = "gpio4", "gpio5"; - drive-strength = <2>; - bias-pull-down; - }; - - blsp2_uart2_default: blsp2-uart2-default { - function = "blsp_uart8"; - pins = "gpio45", "gpio46", "gpio47", "gpio48"; - drive-strength = <16>; - bias-disable; - }; - - blsp2_uart2_sleep: blsp2-uart2-sleep { - function = "gpio"; - pins = "gpio45", "gpio46", "gpio47", "gpio48"; - drive-strength = <2>; - bias-pull-down; - }; - - sdc1_clk_on: clk-on { - pins = "sdc1_clk"; - bias-disable; - drive-strength = <6>; - }; - - sdc1_clk_off: clk-off { - pins = "sdc1_clk"; - bias-disable; - drive-strength = <2>; - }; - - sdc1_cmd_on: cmd-on { - pins = "sdc1_cmd"; - bias-pull-up; - drive-strength = <6>; - }; - - sdc1_cmd_off: cmd-off { - pins = "sdc1_cmd"; - bias-pull-up; - drive-strength = <2>; - }; - - sdc1_data_on: data-on { - pins = "sdc1_data"; - bias-pull-up; - drive-strength = <6>; - }; - - sdc1_data_off: data-off { - pins = "sdc1_data"; - bias-pull-up; - drive-strength = <2>; - }; - - sdc1_rclk_on: rclk-on { - pins = "sdc1_rclk"; - bias-pull-down; - }; - - sdc1_rclk_off: rclk-off { - pins = "sdc1_rclk"; - bias-pull-down; - }; - - i2c1_default: i2c1-default { - function = "blsp_i2c1"; - pins = "gpio2", "gpio3"; - drive-strength = <2>; - bias-disable; - }; - - i2c1_sleep: i2c1-sleep { - function = "gpio"; - pins = "gpio2", "gpio3"; - drive-strength = <2>; - bias-disable; - }; - - i2c2_default: i2c2-default { - function = "blsp_i2c2"; - pins = "gpio6", "gpio7"; - drive-strength = <2>; - bias-disable; - }; - - i2c2_sleep: i2c2-sleep { - function = "gpio"; - pins = "gpio6", "gpio7"; - drive-strength = <2>; - bias-disable; - }; - - i2c5_default: i2c5-default { - /* Don't be fooled! Nobody knows the reason why though... */ - function = "blsp_i2c11"; - pins = "gpio83", "gpio84"; - drive-strength = <2>; - bias-disable; - }; - - i2c5_sleep: i2c5-sleep { - function = "gpio"; - pins = "gpio83", "gpio84"; - drive-strength = <2>; - bias-disable; - }; - - i2c6_default: i2c6-default { - function = "blsp_i2c6"; - pins = "gpio28", "gpio27"; - drive-strength = <2>; - bias-disable; - }; - - i2c6_sleep: i2c6-sleep { - function = "gpio"; - pins = "gpio28", "gpio27"; - drive-strength = <2>; - bias-disable; - }; - - i2c7_default: i2c7-default { - function = "blsp_i2c7"; - pins = "gpio43", "gpio44"; - drive-strength = <2>; - bias-disable; - }; - - i2c7_sleep: i2c7-sleep { - function = "gpio"; - pins = "gpio43", "gpio44"; - drive-strength = <2>; - bias-disable; - }; - - i2c13_default: i2c13-default { - /* Not a typo either. */ - function = "blsp_i2c5"; - pins = "gpio23", "gpio24"; - drive-strength = <2>; - bias-disable; - }; - - i2c13_sleep: i2c13-sleep { - function = "gpio"; - pins = "gpio23", "gpio24"; - drive-strength = <2>; - bias-disable; - }; - - sdc2_clk_on: sdc2-clk-on { - pins = "sdc2_clk"; - bias-disable; - drive-strength = <16>; - }; - - sdc2_clk_off: sdc2-clk-off { - pins = "sdc2_clk"; - bias-disable; - drive-strength = <2>; - }; - - sdc2_cmd_on: sdc2-cmd-on { - pins = "sdc2_cmd"; - bias-pull-up; - drive-strength = <10>; - }; - - sdc2_cmd_off: sdc2-cmd-off { - pins = "sdc2_cmd"; - bias-pull-up; - drive-strength = <2>; - }; - - sdc2_data_on: sdc2-data-on { - pins = "sdc2_data"; - bias-pull-up; - drive-strength = <10>; - }; - - sdc2_data_off: sdc2-data-off { - pins = "sdc2_data"; - bias-pull-up; - drive-strength = <2>; - }; - }; - }; - - smd_rpm: smd { - compatible = "qcom,smd"; - rpm { - interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; - qcom,ipc = <&apcs 8 0>; - qcom,smd-edge = <15>; - qcom,local-pid = <0>; - qcom,remote-pid = <6>; - - rpm_requests: rpm-requests { - compatible = "qcom,rpm-msm8994"; - qcom,smd-channels = "rpm_requests"; +&rpmcc { + compatible = "qcom,rpmcc-msm8992"; +}; - rpmcc: rpmcc { - compatible = "qcom,rpmcc-msm8992"; - #clock-cells = <1>; - }; - }; - }; - }; +&tcsr_mutex { + compatible = "qcom,sfpb-mutex"; +}; - timer { - compatible = "arm,armv8-timer"; - interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, +&timer { + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; - }; - - vreg_vph_pwr: vreg-vph-pwr { - compatible = "regulator-fixed"; - status = "okay"; - regulator-name = "vph-pwr"; - - regulator-min-microvolt = <3600000>; - regulator-max-microvolt = <3600000>; - - regulator-always-on; - }; }; +&tlmm { + compatible = "qcom,msm8992-pinctrl"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts deleted file mode 100644 index ed9034b96013..000000000000 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts +++ /dev/null @@ -1,73 +0,0 @@ -// SPDX-License-Identifier: BSD-3-Clause -/* - * Copyright (c) 2020, Konrad Dybcio - */ - -/dts-v1/; - -#include "msm8994.dtsi" -#include "pm8994.dtsi" -#include "pmi8994.dtsi" - -/ { - model = "Microsoft Lumia 950 XL"; - compatible = "microsoft,cityman", "qcom,msm8994"; - - /* - * Most Lumia 950XL users use GRUB to load their kernels, - * hence there is no need for msm-id and friends. - */ - - /* - * This enables graphical output via bootloader-enabled display. - * acpi=no is required due to WP platforms having ACPI support, but - * only for Windows-based OSes. - */ - chosen { - bootargs = "earlycon=efifb console=efifb acpi=no"; - - #address-cells = <2>; - #size-cells = <2>; - ranges; - }; -}; - -&blsp_i2c1 { - status = "okay"; - - rmi4-i2c-dev@4b { - compatible = "syna,rmi4-i2c"; - reg = <0x4b>; - #address-cells = <1>; - #size-cells = <0>; - - interrupt-parent = <&tlmm>; - interrupts = <77 IRQ_TYPE_EDGE_FALLING>; - - rmi4-f01@1 { - reg = <0x01>; - syna,nosleep-mode = <1>; - }; - - rmi4-f12@12 { - reg = <0x12>; - syna,sensor-type = <1>; - syna,clip-x-low = <0>; - syna,clip-x-high = <1440>; - syna,clip-y-low = <0>; - syna,clip-y-high = <2660>; - }; - }; -}; - -&blsp1_uart2 { - status = "okay"; -}; - -&blsp2_uart2 { - status = "okay"; -}; - -&sdhc1 { - status = "okay"; -}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts new file mode 100644 index 000000000000..d0aaf5750c21 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + * Copyright (c) 2020, Gustave Monce <gustave.monce@outlook.com> + */ + +/dts-v1/; + +#include "msm8994.dtsi" +#include "msm8994-msft-lumia-octagon.dtsi" + +/ { + model = "Microsoft Lumia 950 XL"; + compatible = "microsoft,cityman", "qcom,msm8994"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi new file mode 100644 index 000000000000..3a3790a52a2c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -0,0 +1,909 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Common Board Device Tree for + * Microsoft Mobile MSM8994 Octagon Platforms + * + * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Gustave Monce <gustave.monce@outlook.com> + */ + +#include "pm8994.dtsi" +#include "pmi8994.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +/* + * Delete all generic (msm8994.dtsi) reserved + * memory mappings which are different in this device. + */ +/delete-node/ &adsp_mem; +/delete-node/ &audio_mem; +/delete-node/ &cont_splash_mem; +/delete-node/ &mba_mem; +/delete-node/ &mpss_mem; +/delete-node/ &peripheral_region; +/delete-node/ &rmtfs_mem; +/delete-node/ &smem_mem; + +/ { + /* + * Most Lumia 950/XL users use GRUB to load their kernels, + * hence there is no need for msm-id and friends. + */ + + /* + * This enables graphical output via bootloader-enabled display. + * acpi=no is required due to WP platforms having ACPI support, but + * only for Windows-based OSes. + */ + chosen { + bootargs = "earlycon=efifb console=efifb acpi=no"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + }; + + clocks { + compatible = "simple-bus"; + + divclk4: divclk4 { + compatible = "fixed-clock"; + #clock-cells = <0>; + + clock-frequency = <32768>; + clock-output-names = "divclk4"; + + pinctrl-names = "default"; + pinctrl-0 = <&divclk4_pin_a>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + input-name = "gpio-keys"; + autorepeat; + + volupkey { + label = "Volume Up"; + gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEUP>; + wakeup-source; + debounce-interval = <15>; + }; + + camsnapkey { + label = "Camera Snapshot"; + gpios = <&pm8994_gpios 4 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_CAMERA>; + wakeup-source; + debounce-interval = <15>; + }; + + camfocuskey { + label = "Camera Focus"; + gpios = <&pm8994_gpios 5 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEUP>; + wakeup-source; + debounce-interval = <15>; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_front_default &hall_back_default>; + + label = "GPIO Hall Effect Sensor"; + + hall-front-sensor { + label = "Hall Effect Front Sensor"; + gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + + hall-back-sensor { + label = "Hall Effect Back Sensor"; + gpios = <&tlmm 75 GPIO_ACTIVE_HIGH>; + linux,input-type = <EV_SW>; + linux,code = <SW_MACHINE_COVER>; + linux,can-disable; + }; + }; + + reserved-memory { + /* + * This device being a WP platform has a very different + * memory layout than other Android based devices. + * This memory layout is directly copied from the original + * device UEFI firmware, and adapted based on observations + * using JTAG for the Qualcomm Peripheral Image regions. + */ + + uefi_mem: memory@200000 { + reg = <0 0x200000 0 0x100000>; + no-map; + }; + + mppark_mem: memory@300000 { + reg = <0 0x300000 0 0x80000>; + no-map; + }; + + fbpt_mem: memory@380000 { + reg = <0 0x380000 0 0x1000>; + no-map; + }; + + dbg2_mem: memory@381000 { + reg = <0 0x381000 0 0x4000>; + no-map; + }; + + capsule_mem: memory@385000 { + reg = <0 0x385000 0 0x1000>; + no-map; + }; + + tpmctrl_mem: memory@386000 { + reg = <0 0x386000 0 0x3000>; + no-map; + }; + + uefiinfo_mem: memory@389000 { + reg = <0 0x389000 0 0x1000>; + no-map; + }; + + reset_mem: memory@389000 { + reg = <0 0x389000 0 0x1000>; + no-map; + }; + + resuncached_mem: memory@38e000 { + reg = <0 0x38e000 0 0x72000>; + no-map; + }; + + disp_mem: memory@400000 { + reg = <0 0x400000 0 0x800000>; + no-map; + }; + + uefistack_mem: memory@c00000 { + reg = <0 0xc00000 0 0x40000>; + no-map; + }; + + cpuvect_mem: memory@c40000 { + reg = <0 0xc40000 0 0x10000>; + no-map; + }; + + rescached_mem: memory@400000 { + reg = <0 0xc50000 0 0xb0000>; + no-map; + }; + + tzapps_mem: memory@6500000 { + reg = <0 0x6500000 0 0x500000>; + no-map; + }; + + smem_mem: memory@6a00000 { + reg = <0 0x6a00000 0 0x200000>; + no-map; + }; + + hyp_mem: memory@6c00000 { + reg = <0 0x6c00000 0 0x100000>; + no-map; + }; + + tz_mem: memory@6d00000 { + reg = <0 0x6d00000 0 0x160000>; + no-map; + }; + + rfsa_adsp_mem: memory@6e60000 { + reg = <0 0x6e60000 0 0x10000>; + no-map; + }; + + rfsa_mpss_mem: memory@6e70000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0x6e70000 0 0x10000>; + no-map; + + qcom,client-id = <1>; + }; + + /* + * Value obtained from the device original ACPI DSDT table + * MPSS_EFS / SBL + */ + mba_mem: memory@6e80000 { + reg = <0 0x6e80000 0 0x180000>; + no-map; + }; + + /* + * Peripheral Image loader region begin! + * The region reserved for pil is 0x7000000-0xef00000 + */ + + mpss_mem: memory@7000000 { + reg = <0 0x7000000 0 0x5a00000>; + no-map; + }; + + adsp_mem: memory@ca00000 { + reg = <0 0xca00000 0 0x1800000>; + no-map; + }; + + venus_mem: memory@e200000 { + reg = <0 0xe200000 0 0x500000>; + no-map; + }; + + pil_metadata_mem: memory@e700000 { + reg = <0 0xe700000 0 0x4000>; + no-map; + }; + + memory@e704000 { + reg = <0 0xe704000 0 0x7fc000>; + no-map; + }; + /* Peripheral Image loader region end */ + + cnss_mem: memory@ef00000 { + reg = <0 0xef00000 0 0x300000>; + no-map; + }; + }; +}; + +&blsp1_i2c1 { + status = "okay"; + + rmi4-i2c-dev@4b { + compatible = "syna,rmi4-i2c"; + reg = <0x4b>; + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&tlmm>; + interrupts = <77 IRQ_TYPE_EDGE_FALLING>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4-f12@12 { + reg = <0x12>; + syna,sensor-type = <1>; + syna,clip-x-low = <0>; + syna,clip-x-high = <1440>; + syna,clip-y-low = <0>; + syna,clip-y-high = <2560>; + }; + }; +}; + +&blsp1_i2c2 { + status = "okay"; + + /* + * This device uses the Texas Instruments TAS2553, however the TAS2552 driver + * seems to work here. In the future a proper driver might need to + * be written for this device. + */ + tas2553: tas2553@40 { + compatible = "ti,tas2552"; + reg = <0x40>; + + vbat-supply = <&vph_pwr>; + iovdd-supply = <&vreg_s4a_1p8>; + avdd-supply = <&vreg_s4a_1p8>; + + enable-gpio = <&pm8994_gpios 12 GPIO_ACTIVE_HIGH>; + }; +}; + +&blsp1_i2c5 { + status = "okay"; + + ak09912: magnetometer@c { + compatible = "asahi-kasei,ak09912"; + reg = <0xc>; + + interrupt-parent = <&tlmm>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vreg_l18a_2p85>; + vid-supply = <&vreg_lvs2a_1p8>; + }; + + zpa2326: barometer@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + + interrupt-parent = <&tlmm>; + interrupts = <74 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vreg_lvs2a_1p8>; + }; + + mpu6050: accelerometer@68 { + compatible = "invensense,mpu6500"; + reg = <0x68>; + + interrupt-parent = <&tlmm>; + interrupts = <64 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vreg_lvs2a_1p8>; + vddio-supply = <&vreg_lvs2a_1p8>; + }; +}; + +&blsp1_i2c6 { + status = "okay"; + + pn547: pn547@28 { + compatible = "nxp,pn544-i2c"; + + reg = <0x28>; + + interrupt-parent = <&tlmm>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + + enable-gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&blsp2_i2c1 { + status = "okay"; + + sideinteraction: ad7147_captouch@2c { + compatible = "ad,ad7147_captouch"; + reg = <0x2c>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&grip_default>; + pinctrl-1 = <&grip_sleep>; + + interrupts = <&tlmm 96 IRQ_TYPE_EDGE_FALLING>; + + button_num = <8>; + touchpad_num = <0>; + wheel_num = <0>; + slider_num = <0>; + + vcc-supply = <&vreg_l18a_2p85>; + }; + + /* + * The QPDS-T900/QPDS-T930 is a customized part built for Nokia + * by Avago. It is very similar to the Avago APDS-9930 with some + * minor differences. In the future a proper driver might need to + * be written for this device. For now this works fine. + */ + qpdst900: qpdst900@39 { + compatible = "avago,apds9930"; + reg = <0x39>; + + interrupt-parent = <&tlmm>; + interrupts = <40 IRQ_TYPE_EDGE_FALLING>; + }; +}; + +&blsp2_i2c5 { + status = "okay"; + + fm_radio: si4705@11 { + compatible = "silabs,si470x"; + reg = <0x11>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&tlmm 93 GPIO_ACTIVE_HIGH>; + }; + + vreg_lpddr_1p1: fan53526a@6c { + compatible = "fcs,fan53526"; + reg = <0x6c>; + + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + vin-supply = <&vph_pwr>; + fcs,suspend-voltage-selector = <1>; + regulator-always-on; /* Turning off DDR power doesn't sound good. */ + }; + + /* ANX7816 HDMI bridge (needs MDSS HDMI) */ +}; + +&blsp2_spi4 { + status = "okay"; + + /* + * This device is a Lattice UC120 USB-C PD PHY. + * It is actually a Lattice iCE40 FPGA pre-programmed by + * the device firmware with a specific bitstream + * enabling USB Type C PHY functionality. + * Communication is done via a proprietary protocol over SPI. + * + * TODO: Once a proper driver is available, replace this. + */ + uc120: ice5lp2k@0 { + compatible = "lattice,ice40-fpga-mgr"; + reg = <0>; + spi-max-frequency = <5000000>; + cdone-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pmi8994_gpios 4 GPIO_ACTIVE_LOW>; + }; +}; + +&blsp2_uart2 { + status = "okay"; + + qca6174_bt: bluetooth { + compatible = "qcom,qca6174-bt"; + + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + }; +}; + +&pm8994_gpios { + bt_en_gpios: bt_en_gpios { + pinconf { + pins = "gpio19"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + power-source = <PM8994_GPIO_S4>; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + bias-pull-down; + }; + }; + + divclk4_pin_a: divclk4 { + pinconf { + pins = "gpio18"; + function = PMIC_GPIO_FUNC_FUNC2; + power-source = <PM8994_GPIO_S4>; + bias-disable; + }; + }; +}; + +&pm8994_pon { + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0 8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + linux,code = <KEY_POWER>; + }; + + volwnkey { + compatible = "qcom,pm8941-resin"; + interrupts = <0 8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + linux,code = <KEY_VOLUMEDOWN>; + }; +}; + +&pmi8994_gpios { + pinctrl-0 = <&hd3ss460_pol &hd3ss460_amsel &hd3ss460_en>; + pinctrl-names = "default"; + + /* + * This device uses a TI HD3SS460 Type-C MUX + * As this device has no driver currently, + * the configuration for USB Face Up is set-up here. + * + * TODO: remove once a driver is available + * TODO: add VBUS GPIO 5 + */ + hd3ss460_pol: pol_low { + pins = "gpio8"; + drive-strength = <3>; + bias-pull-down; + }; + + hd3ss460_amsel: amsel_high { + pins = "gpio9"; + drive-strength = <1>; + bias-pull-up; + }; + + hd3ss460_en: en_high { + pins = "gpio10"; + drive-strength = <1>; + bias-pull-up; + }; +}; + +&pmi8994_spmi_regulators { + vdd_gfx: s2@1700 { + reg = <0x1700 0x100>; + regulator-min-microvolt = <980000>; + regulator-max-microvolt = <980000>; + }; +}; + +&rpm_requests { + /* These values were taken from the original firmware ACPI tables */ + pm8994_regulators: pm8994-regulators { + compatible = "qcom,rpm-pm8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_l1-supply = <&vreg_s1b_1p0>; + vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>; + vdd_l3_l11-supply = <&vreg_s3a_1p3>; + vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>; + vdd_l5_l7-supply = <&vreg_s5a_2p15>; + vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>; + vdd_l8_l16_l30-supply = <&vph_pwr>; + vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>; + vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>; + vdd_l14_l15-supply = <&vreg_s5a_2p15>; + vdd_l17_l29-supply = <&vph_pwr_bbyp>; + vdd_l20_l21-supply = <&vph_pwr_bbyp>; + vdd_l25-supply = <&vreg_s5a_2p15>; + vdd_lvs1_2-supply = <&vreg_s4a_1p8>; + + /* S1, S2, S6 and S12 are managed by RPMPD */ + + vreg_s3a_1p3: s3 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-allow-set-load; + regulator-system-load = <300000>; + }; + + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-always-on; + regulator-system-load = <325000>; + }; + + vreg_s5a_2p15: s5 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + regulator-allow-set-load; + regulator-system-load = <325000>; + }; + + vreg_s7a_1p0: s7 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + /* + * S8 - SPMI-managed VDD_APC0 + * S9, S10 and S11 (the main one) - SPMI-managed VDD_APC1 + */ + + vreg_l1a_1p0: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l2a_1p25: l2 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-allow-set-load; + regulator-system-load = <4160>; + }; + + vreg_l3a_1p2: l3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l4a_1p225: l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + /* L5 is inaccessible from RPM */ + + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-system-load = <1000>; + }; + + /* L7 is inaccessible from RPM */ + + vreg_l8a_1p8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l11a_1p2: l11 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <35000>; + }; + + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <50000>; + }; + + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <22000>; + }; + + vreg_l14a_1p8: l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <52000>; + }; + + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + vreg_l17a_2p7: l17 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <300000>; + }; + + vreg_l18a_2p85: l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <600000>; + }; + + vreg_l19a_3p3: l19 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <500000>; + }; + + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-boot-on; + regulator-allow-set-load; + regulator-system-load = <570000>; + }; + + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + + vreg_l22a_3p0: l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <150000>; + }; + + vreg_l23a_2p8: l23 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3150000>; + regulator-allow-set-load; + regulator-system-load = <5800>; + }; + + vreg_l25a_1p1: l25 { + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l26a_1p0: l26 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l27a_1p05: l27 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <500000>; + }; + + vreg_l28a_1p0: l28 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <26000>; + }; + + vreg_l29a_2p8: l29 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l30a_1p8: l30 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <2500>; + }; + + vreg_l31a_1p2: l31 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <600000>; + }; + + vreg_l32a_1p8: l32 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs1a_1p8: lvs1 { }; + + vreg_lvs2a_1p8: lvs2 { }; + }; + + pmi8994_regulators: pmi8994-regulators { + compatible = "qcom,rpm-pmi8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + vreg_s1b_1p0: s1 { + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + + /* S2 & S3 - VDD_GFX */ + + vph_pwr_bbyp: boost-bypass { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; +}; + +&sdhc1 { + status = "okay"; + + /* + * This device is shipped with HS400 capabable eMMCs + * However various brands have been used in various product batches, + * including a Samsung eMMC (BGND3R) which features a quirk with HS400. + * Set the speed to HS200 as a safety measure. + */ + mmc-hs200-1_8v; +}; + +&sdhc2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; + + vmmc-supply = <&vreg_l21a_2p95>; + vqmmc-supply = <&vreg_l13a_2p95>; + + cd-gpios = <&pm8994_gpios 8 GPIO_ACTIVE_LOW>; +}; + +&tlmm { + grip_default: grip-default { + pins = "gpio39"; + function = "gpio"; + drive-strength = <6>; + bias-pull-down; + }; + + grip_sleep: grip-sleep { + pins = "gpio39"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + hall_front_default: hall-front-default { + pins = "gpio42"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + hall_back_default: hall-back-default { + pins = "gpio75"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts new file mode 100644 index 000000000000..b5e90c85aaf6 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z3+/Z4"; + compatible = "sony,ivy-row", "qcom,msm8994"; +}; + +&pm8994_l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; +}; + +&pm8994_l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; +}; + +/delete-node/ &pm8994_l19; +/delete-node/ &pm8994_l32; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts new file mode 100644 index 000000000000..a1d1a075941a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z4 Tablet (LTE)"; + compatible = "sony,karin-row", "qcom,msm8994"; +}; + +&blsp2_i2c5 { + /* + * TI LP8557 backlight driver @ 2c + * AD AD7146 touch controller @ 2f + * sii8620 HDMI/MHL bridge @ 72 (kitakami-common) + */ +}; + +&pm8994_l3 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; +}; + +&pm8994_l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; +}; + +&pm8994_l22 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; +}; + +&pm8994_l25 { + regulator-min-microvolt = <1037500>; + regulator-max-microvolt = <1037500>; +}; + +/delete-node/ &pm8994_l32; +/* Z4 tablets use a different touchscreen. */ +/delete-node/ &touchscreen; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts new file mode 100644 index 000000000000..1385956a69f3 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z5 Premium"; + compatible = "sony,satsuki-row", "qcom,msm8994"; +}; + +&pm8994_l14 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts index 5d6bbbf6c119..d3ba9867a369 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> */ /dts-v1/; @@ -11,3 +11,5 @@ model = "Sony Xperia Z5"; compatible = "sony,sumire-row", "qcom,msm8994"; }; + +/delete-node/ &pm8994_l19; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts new file mode 100644 index 000000000000..f129479bbf95 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z5 Compact"; + compatible = "sony,suzuran-row", "qcom,msm8994"; +}; + +&pm8994_l14 { + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; +}; + +/delete-node/ &pm8994_l19; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 791f254ac3f8..48de66bf19c4 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> */ #include "msm8994.dtsi" @@ -11,8 +11,17 @@ / { /* required for bootloader to select correct board */ - qcom,msm-id = <0xcf 0x20001>; + + /* + * We support MSM8994 v2 (0x20000) and v2.1 (0x20001). + * The V1 chip (0x0 and 0x10000) is significantly different + * and requires driver-side changes (including CPR, be warned!!). + * Besides that, it's very rare. + */ + qcom,msm-id = <207 0x20000>, <207 0x20001>; + /* We only use pm8994+pmi8994. */ qcom,pmic-id = <0x10009 0x1000a 0x00 0x00>; + /* This property is shared across all kitakami devices. */ qcom,board-id = <8 0>; /* Kitakami firmware doesn't support PSCI */ @@ -63,53 +72,29 @@ }; reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - /* This is for getting crash logs using Android downstream kernels */ ramoops@1fe00000 { compatible = "ramoops"; - reg = <0x0 0x1fe00000 0x0 0x200000>; + reg = <0 0x1fe00000 0 0x200000>; console-size = <0x100000>; record-size = <0x10000>; ftrace-size = <0x10000>; pmsg-size = <0x80000>; }; - continuous_splash: framebuffer@3401000{ - reg = <0x0 0x3401000 0x0 0x2200000>; - no-map; - }; - - dfps_data_mem: dfps_data_mem@3400000 { - reg = <0x0 0x3400000 0x0 0x1000>; - no-map; - }; - - peripheral_region: peripheral_region@7400000 { - reg = <0x0 0x7400000 0x0 0x1c00000>; - no-map; - }; - - modem_region: modem_region@9000000 { - reg = <0x0 0x9000000 0x0 0x5a00000>; - no-map; - }; - - tzapp: modem_region@ea00000 { - reg = <0x0 0xea00000 0x0 0x1900000>; + fb_region: fb_region@40000000 { + reg = <0 0x40000000 0 0x1000000>; no-map; }; - fb_region: fb_region@40000000 { - reg = <0x00 0x40000000 0x00 0x1000000>; + tzapp: memory@c7800000 { + reg = <0 0xc7800000 0 0x1900000>; no-map; }; }; }; -&blsp_spi0 { +&blsp1_spi1 { status = "okay"; /* FPC fingerprint reader */ @@ -117,94 +102,330 @@ /* I2C1 is disabled on this board */ -&blsp_i2c2 { +&blsp1_i2c2 { status = "okay"; + clock-frequency = <355000>; - /* NXP NFC */ + /* NXP PN547 NFC */ }; -&blsp_i2c4 { +&blsp1_i2c4 { status = "okay"; + clock-frequency = <355000>; /* Empty but active */ }; -&blsp_i2c5 { +&blsp1_i2c6 { status = "okay"; + clock-frequency = <355000>; - /* SMB1357 charger and sii8620 HDMI/MHL bridge */ -}; + touchscreen: rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + reg = <0x2c>; + #address-cells = <1>; + #size-cells = <0>; -&blsp_i2c6 { - status = "okay"; + interrupt-parent = <&tlmm>; + interrupts = <42 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_reset_active>; + + vdd-supply = <&pm8994_l22>; + vio-supply = <&pm8994_s4>; + + syna,reset-delay-ms = <220>; + syna,startup-delay-ms = <220>; - /* Synaptics touchscreen */ + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + }; + }; }; &blsp1_uart2 { status = "okay"; }; +&blsp2_i2c5 { + status = "okay"; + clock-frequency = <355000>; + + /* sii8620 HDMI/MHL bridge */ +}; + &blsp2_uart2 { status = "okay"; }; +/* + * Kitakami bootloader only turns cont_splash on when it detects + * specific downstream MDSS/backlight nodes in the active DTB. + * One way to use that framebuffer is to load a secondary instance of + * LK with the downstream DTB appended and then, only from there, load + * mainline Linux. + */ +&cont_splash_mem { + reg = <0 0x3401000 0 0x2200000>; +}; + +&pmi8994_spmi_regulators { + /* + * Yeah, this one *is* managed by RPMPD, but also needs + * to be hacked up as a-o due to the GPU device only accepting a single + * power domain.. which still isn't enough and forces us to bind + * OXILI_CX and OXILI_GX together! + */ + vdd_gfx: s2@1700 { + reg = <0x1700 0x100>; + regulator-name = "VDD_GFX"; + regulator-min-microvolt = <980000>; + regulator-max-microvolt = <980000>; + + /* hack until we rig up the gpu consumer */ + regulator-always-on; + }; +}; + &rpm_requests { pm8994_regulators: pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; - vdd_l1-supply = <&pm8994_s1>; - vdd_l2_26_28-supply = <&pm8994_s3>; - vdd_l3_11-supply = <&pm8994_s3>; - vdd_l4_27_31-supply = <&pm8994_s3>; - vdd_l5_7-supply = <&pm8994_s3>; - vdd_l6_12_32-supply = <&pm8994_s5>; - vdd_l8_16_30-supply = <&vreg_vph_pwr>; - vdd_l9_10_18_22-supply = <&vreg_vph_pwr>; - vdd_l13_19_23_24-supply = <&vreg_vph_pwr>; - vdd_l14_15-supply = <&pm8994_s5>; - vdd_l17_29-supply = <&vreg_vph_pwr>; - vdd_l20_21-supply = <&vreg_vph_pwr>; - vdd_l25-supply = <&pm8994_s5>; - vdd_lvs1_2 = <&pm8994_s4>; - - pm8994_s1: s1 {}; - pm8994_s2: s2 {}; - pm8994_s3: s3 {}; - pm8994_s4: s4 {}; - pm8994_s5: s5 {}; - pm8994_s6: s6 {}; - pm8994_s7: s7 {}; - - pm8994_l1: l1 {}; - pm8994_l2: l2 {}; - pm8994_l3: l3 {}; - pm8994_l4: l4 {}; - pm8994_l6: l6 {}; - pm8994_l8: l8 {}; - pm8994_l9: l9 {}; - pm8994_l10: l10 {}; - pm8994_l11: l11 {}; - pm8994_l12: l12 {}; - pm8994_l13: l13 {}; - pm8994_l14: l14 {}; - pm8994_l15: l15 {}; - pm8994_l16: l16 {}; - pm8994_l17: l17 {}; - pm8994_l18: l18 {}; - pm8994_l19: l19 {}; - pm8994_l20: l20 {}; - pm8994_l21: l21 {}; - pm8994_l22: l22 {}; - pm8994_l23: l23 {}; - pm8994_l24: l24 {}; - pm8994_l25: l25 {}; - pm8994_l26: l26 {}; - pm8994_l27: l27 {}; - pm8994_l28: l28 {}; - pm8994_l29: l29 {}; - pm8994_l30: l30 {}; - pm8994_l31: l31 {}; - pm8994_l32: l32 {}; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_l1-supply = <&pmi8994_s1>; + vdd_l2_l26_l28-supply = <&pm8994_s3>; + vdd_l3_l11-supply = <&pm8994_s3>; + vdd_l4_l27_l31-supply = <&pm8994_s3>; + vdd_l5_l7-supply = <&pm8994_s5>; + vdd_l6_l12_l32-supply = <&pm8994_s5>; + vdd_l8_l16_l30-supply = <&vph_pwr>; + vdd_l9_l10_l18_l22-supply = <&pmi8994_bby>; + vdd_l13_l19_l23_l24-supply = <&pmi8994_bby>; + vdd_l14_l15-supply = <&pm8994_s5>; + vdd_l17_l29-supply = <&pmi8994_bby>; + vdd_l20_l21-supply = <&pmi8994_bby>; + vdd_l25-supply = <&pm8994_s3>; + vdd_lvs1_lvs2-supply = <&pm8994_s4>; + + /* S1, S2, S6 and S12 are managed by RPMPD */ + + pm8994_s3: s3 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + }; + + pm8994_s4: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-always-on; + regulator-system-load = <325000>; + }; + + pm8994_s5: s5 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + }; + + pm8994_s7: s7 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + /* + * S8 - SPMI-managed VDD_APC0 + * S9, S10 and S11 (the main one) - SPMI-managed VDD_APC1 + */ + + pm8994_l1: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + pm8994_l2: l2 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l3: l3 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + pm8994_l4: l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + /* L5 is inaccessible from RPM */ + + pm8994_l6: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + /* L7 is inaccessible from RPM */ + + pm8994_l8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l9: l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l10: l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l11: l11 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + pm8994_l12: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l13: l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + pm8994_l14: l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l15: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l16: l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l17: l17 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + }; + + pm8994_l18: l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + + pm8994_l19: l19 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + pm8994_l20: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-boot-on; + regulator-allow-set-load; + regulator-system-load = <570000>; + }; + + pm8994_l21: l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + + pm8994_l22: l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + pm8994_l23: l23 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + pm8994_l24: l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3150000>; + }; + + pm8994_l25: l25 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + pm8994_l26: l26 { + regulator-min-microvolt = <987500>; + regulator-max-microvolt = <987500>; + }; + + pm8994_l27: l27 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + pm8994_l28: l28 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l29: l29 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l30: l30 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l31: l31 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l32: l32 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; pm8994_lvs1: lvs1 {}; pm8994_lvs2: lvs2 {}; @@ -213,22 +434,34 @@ pmi8994_regulators: pmi8994-regulators { compatible = "qcom,rpm-pmi8994-regulators"; - pmi8994_s1: s1 {}; - pmi8994_s2: s2 {}; - pmi8994_s3: s3 {}; - pmi8994_bby: boost-bypass {}; + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + pmi8994_s1: s1 { + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + + /* S2 & S3 - VDD_GFX */ + + pmi8994_bby: boost-bypass { + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3600000>; + }; }; }; &sdhc1 { - /* There is an issue with the eMMC causing permanent + /* + * There is an issue with the eMMC causing permanent * damage to the card if a quirk isn't addressed. * Until it's fixed, disable the MMC so as not to brick * devices. */ status = "disabled"; - /* Downstream pushes 2.95V to the sdhci device, + /* + * Downstream pushes 2.95V to the sdhci device, * but upstream driver REALLY wants to make vmmc 1.8v * cause of the hs400-1_8v mode. MMC works fine without * that regulator, so let's not use it for now. @@ -238,3 +471,27 @@ * vqmmc-supply = <&pm8994_s4>; */ }; + +&sdhc2 { + status = "okay"; + + cd-gpios = <&tlmm 100 0>; + vmmc-supply = <&pm8994_l21>; + vqmmc-supply = <&pm8994_l13>; +}; + +&tlmm { + ts_int_active: ts-int-active { + pins = "gpio42"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + + ts_reset_active: ts-reset-active { + pins = "gpio109"; + drive-strength = <2>; + bias-disable; + output-low; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index 6e083a2f690b..f49d442d2edf 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -4,6 +4,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/qcom,gcc-msm8994.h> +#include <dt-bindings/power/qcom-rpmpd.h> / { interrupt-parent = <&intc>; @@ -131,11 +132,11 @@ cpu = <&CPU5>; }; - core2 { + cpu6_map: core2 { cpu = <&CPU6>; }; - core3 { + cpu7_map: core3 { cpu = <&CPU7>; }; }; @@ -154,6 +155,12 @@ reg = <0 0 0 0>; }; + tcsr_mutex: hwlock { + compatible = "qcom,tcsr-mutex"; + syscon = <&tcsr_mutex_regs 0 0x80>; + #hwlock-cells = <1>; + }; + pmu { compatible = "arm,cortex-a53-pmu"; interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4)| IRQ_TYPE_LEVEL_HIGH)>; @@ -169,8 +176,51 @@ #size-cells = <2>; ranges; + dfps_data_mem: dfps_data_mem@3400000 { + reg = <0 0x03400000 0 0x1000>; + no-map; + }; + + cont_splash_mem: memory@3800000 { + reg = <0 0x03800000 0 0x2400000>; + no-map; + }; + smem_mem: smem_region@6a00000 { - reg = <0x0 0x6a00000 0x0 0x200000>; + reg = <0 0x06a00000 0 0x200000>; + no-map; + }; + + mpss_mem: memory@7000000 { + reg = <0 0x07000000 0 0x5a00000>; + no-map; + }; + + peripheral_region: memory@ca00000 { + reg = <0 0x0ca00000 0 0x1f00000>; + no-map; + }; + + rmtfs_mem: memory@c6400000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xc6400000 0 0x180000>; + no-map; + + qcom,client-id = <1>; + }; + + mba_mem: memory@c6700000 { + reg = <0 0xc6700000 0 0x100000>; + no-map; + }; + + audio_mem: memory@c7000000 { + reg = <0 0xc7000000 0 0x800000>; + no-map; + }; + + adsp_mem: memory@c9400000 { + reg = <0 0xc9400000 0 0x3f00000>; no-map; }; }; @@ -192,6 +242,35 @@ compatible = "qcom,rpmcc-msm8994"; #clock-cells = <1>; }; + + rpmpd: power-controller { + compatible = "qcom,msm8994-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_ret: opp1 { + opp-level = <1>; + }; + rpmpd_opp_svs_krait: opp2 { + opp-level = <2>; + }; + rpmpd_opp_svs_soc: opp3 { + opp-level = <3>; + }; + rpmpd_opp_nom: opp4 { + opp-level = <4>; + }; + rpmpd_opp_turbo: opp5 { + opp-level = <5>; + }; + rpmpd_opp_super_turbo: opp6 { + opp-level = <6>; + }; + }; + }; }; }; }; @@ -203,6 +282,55 @@ hwlocks = <&tcsr_mutex 3>; }; + smp2p-lpass { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + + interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 10>; + + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + adsp_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + adsp_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-modem { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 14>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + modem_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + modem_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + soc: soc { #address-cells = <1>; @@ -385,7 +513,7 @@ status = "disabled"; }; - blsp_i2c1: i2c@f9923000 { + blsp1_i2c1: i2c@f9923000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9923000 0x500>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; @@ -393,6 +521,8 @@ <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>; clock-names = "iface", "core"; clock-frequency = <400000>; + dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_default>; pinctrl-1 = <&i2c1_sleep>; @@ -401,7 +531,7 @@ status = "disabled"; }; - blsp_spi0: spi@f9923000 { + blsp1_spi1: spi@f9923000 { compatible = "qcom,spi-qup-v2.2.1"; reg = <0xf9923000 0x500>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; @@ -412,21 +542,21 @@ dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp1_spi0_default>; - pinctrl-1 = <&blsp1_spi0_sleep>; + pinctrl-0 = <&blsp1_spi1_default>; + pinctrl-1 = <&blsp1_spi1_sleep>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; - blsp_i2c2: i2c@f9924000 { + blsp1_i2c2: i2c@f9924000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9924000 0x500>; interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; clock-names = "iface", "core"; - clock-frequency = <355000>; + clock-frequency = <400000>; dmas = <&blsp1_dma 14>, <&blsp1_dma 15>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; @@ -439,14 +569,16 @@ /* I2C3 doesn't exist */ - blsp_i2c4: i2c@f9926000 { + blsp1_i2c4: i2c@f9926000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9926000 0x500>; interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>; clock-names = "iface", "core"; - clock-frequency = <355000>; + clock-frequency = <400000>; + dmas = <&blsp1_dma 18>, <&blsp1_dma 19>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c4_default>; pinctrl-1 = <&i2c4_sleep>; @@ -455,31 +587,32 @@ status = "disabled"; }; - blsp2_dma: dma-controller@f9944000 { - compatible = "qcom,bam-v1.7.0"; - reg = <0xf9944000 0x19000>; - interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP2_AHB_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - qcom,controlled-remotely; - num-channels = <18>; - qcom,num-ees = <4>; + blsp1_i2c5: i2c@f9927000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9927000 0x500>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp2_dma 20>, <&blsp2_dma 21>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c5_default>; + pinctrl-1 = <&i2c5_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; - /* According to downstream kernels, i2c6 - * comes before i2c5 address-wise... - */ - - blsp_i2c6: i2c@f9928000 { + blsp1_i2c6: i2c@f9928000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9928000 0x500>; interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>; clock-names = "iface", "core"; - clock-frequency = <355000>; + clock-frequency = <400000>; dmas = <&blsp1_dma 22>, <&blsp1_dma 23>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; @@ -490,10 +623,23 @@ status = "disabled"; }; + blsp2_dma: dma-controller@f9944000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0xf9944000 0x19000>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + qcom,controlled-remotely; + num-channels = <18>; + qcom,num-ees = <4>; + }; + blsp2_uart2: serial@f995e000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0xf995e000 0x1000>; - interrupts = <GIC_SPI 146 IRQ_TYPE_EDGE_FALLING>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; clock-names = "core", "iface"; clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; @@ -505,7 +651,43 @@ status = "disabled"; }; - blsp_i2c5: i2c@f9967000 { + blsp2_i2c1: i2c@f9963000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9963000 0x500>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>, + <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp2_dma 12>, <&blsp2_dma 13>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c7_default>; + pinctrl-1 = <&i2c7_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_spi4: spi@f9966000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0xf9966000 0x500>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_QUP4_SPI_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + spi-max-frequency = <19200000>; + dmas = <&blsp2_dma 18>, <&blsp2_dma 19>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_spi10_default>; + pinctrl-1 = <&blsp2_spi10_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_i2c5: i2c@f9967000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9967000 0x500>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; @@ -516,8 +698,8 @@ dmas = <&blsp2_dma 20>, <&blsp2_dma 21>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c5_default>; - pinctrl-1 = <&i2c5_sleep>; + pinctrl-0 = <&i2c11_default>; + pinctrl-1 = <&i2c11_sleep>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -588,16 +770,18 @@ blsp2_uart2_default: blsp2-uart2-default { function = "blsp_uart8"; - pins = "gpio45", "gpio46"; - drive-strength = <2>; + pins = "gpio45", "gpio46", + "gpio47", "gpio48"; + drive-strength = <16>; bias-disable; }; blsp2_uart2_sleep: blsp2-uart2-sleep { function = "gpio"; - pins = "gpio45", "gpio46"; + pins = "gpio45", "gpio46", + "gpio47", "gpio48"; drive-strength = <2>; - bias-pull-down; + bias-disable; }; i2c1_default: i2c1-default { @@ -671,7 +855,56 @@ bias-disable; }; - blsp1_spi0_default: blsp1-spi0-default { + i2c7_default: i2c7-default { + function = "blsp_i2c7"; + pins = "gpio44", "gpio43"; + drive-strength = <2>; + bias-disable; + }; + + i2c7_sleep: i2c7-sleep { + function = "gpio"; + pins = "gpio44", "gpio43"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_spi10_default: blsp2-spi10-default { + default { + function = "blsp_spi10"; + pins = "gpio53", "gpio54", "gpio55"; + drive-strength = <10>; + bias-pull-down; + }; + cs { + function = "gpio"; + pins = "gpio55"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_spi10_sleep: blsp2-spi10-sleep { + pins = "gpio53", "gpio54", "gpio55"; + drive-strength = <2>; + bias-disable; + }; + + i2c11_default: i2c11-default { + function = "blsp_i2c11"; + pins = "gpio83", "gpio84"; + drive-strength = <2>; + bias-disable; + }; + + i2c11_sleep: i2c11-sleep { + function = "gpio"; + pins = "gpio83", "gpio84"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_spi1_default: blsp1-spi1-default { default { function = "blsp_spi1"; pins = "gpio0", "gpio1", "gpio3"; @@ -686,7 +919,7 @@ }; }; - blsp1_spi0_sleep: blsp1-spi0-sleep { + blsp1_spi1_sleep: blsp1-spi1-sleep { pins = "gpio0", "gpio1", "gpio3"; drive-strength = <2>; bias-disable; @@ -776,13 +1009,7 @@ }; }; - tcsr_mutex: hwlock { - compatible = "qcom,tcsr-mutex"; - syscon = <&tcsr_mutex_regs 0 0x80>; - #hwlock-cells = <1>; - }; - - timer { + timer: timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 2 0xff08>, <GIC_PPI 3 0xff08>, @@ -790,9 +1017,9 @@ <GIC_PPI 1 0xff08>; }; - vreg_vph_pwr: vreg-vph-pwr { + vph_pwr: vph-pwr-regulator { compatible = "regulator-fixed"; - regulator-name = "vph-pwr"; + regulator-name = "vph_pwr"; regulator-min-microvolt = <3600000>; regulator-max-microvolt = <3600000>; diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi index 7eef07e73e25..ce430ba9c118 100644 --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi @@ -750,6 +750,8 @@ ranges = <0x01000000 0x0 0x0c200000 0x0c200000 0x0 0x100000>, <0x02000000 0x0 0x0c300000 0x0c300000 0x0 0xd00000>; + device_type = "pci"; + interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi"; #interrupt-cells = <1>; @@ -802,6 +804,8 @@ ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>, <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>; + device_type = "pci"; + interrupts = <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi"; #interrupt-cells = <1>; diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi index 00d84fb21798..b500f24d47bc 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi @@ -74,6 +74,14 @@ cpu-idle-states = <&BIG_CPU_SLEEP_1>; }; +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + &pm8005_lsid1 { pm8005-regulators { compatible = "qcom,pm8005-regulators"; @@ -295,6 +303,14 @@ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; }; +&ufshc { + status = "okay"; +}; + +&ufsphy { + status = "okay"; +}; + &usb3 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi index cec42437b302..c1ef0c71d5f5 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi @@ -106,6 +106,14 @@ // status = "okay"; }; +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + &pm8005_lsid1 { pm8005-regulators { compatible = "qcom,pm8005-regulators"; @@ -345,6 +353,7 @@ }; &ufshc { + status = "okay"; vcc-supply = <&vreg_l20a_2p95>; vccq-supply = <&vreg_l26a_1p2>; vccq2-supply = <&vreg_s4a_1p8>; @@ -354,6 +363,7 @@ }; &ufsphy { + status = "okay"; vdda-phy-supply = <&vreg_l1a_0p875>; vdda-pll-supply = <&vreg_l2a_1p2>; vddp-ref-clk-supply = <&vreg_l26a_1p2>; diff --git a/arch/arm64/boot/dts/qcom/msm8998-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8998-pins.dtsi deleted file mode 100644 index 7c222cbf19d9..000000000000 --- a/arch/arm64/boot/dts/qcom/msm8998-pins.dtsi +++ /dev/null @@ -1,108 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* Copyright (c) 2018, The Linux Foundation. All rights reserved. */ - -&tlmm { - sdc2_clk_on: sdc2_clk_on { - config { - pins = "sdc2_clk"; - bias-disable; /* NO pull */ - drive-strength = <16>; /* 16 mA */ - }; - }; - - sdc2_clk_off: sdc2_clk_off { - config { - pins = "sdc2_clk"; - bias-disable; /* NO pull */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_cmd_on: sdc2_cmd_on { - config { - pins = "sdc2_cmd"; - bias-pull-up; /* pull up */ - drive-strength = <10>; /* 10 mA */ - }; - }; - - sdc2_cmd_off: sdc2_cmd_off { - config { - pins = "sdc2_cmd"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_data_on: sdc2_data_on { - config { - pins = "sdc2_data"; - bias-pull-up; /* pull up */ - drive-strength = <10>; /* 10 mA */ - }; - }; - - sdc2_data_off: sdc2_data_off { - config { - pins = "sdc2_data"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_cd_on: sdc2_cd_on { - mux { - pins = "gpio95"; - function = "gpio"; - }; - - config { - pins = "gpio95"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_cd_off: sdc2_cd_off { - mux { - pins = "gpio95"; - function = "gpio"; - }; - - config { - pins = "gpio95"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - blsp1_uart3_on: blsp1_uart3_on { - tx { - pins = "gpio45"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - - rx { - pins = "gpio46"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - - cts { - pins = "gpio47"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - - rfr { - pins = "gpio48"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - }; -}; diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index ebdaaf1dfca4..1f2e93aa6553 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -133,6 +133,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x0>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L2_0: l2-cache { @@ -152,6 +153,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x1>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L1_I_1: l1-icache { @@ -167,6 +169,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x2>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L1_I_2: l1-icache { @@ -182,6 +185,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x3>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L1_I_3: l1-icache { @@ -197,6 +201,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x100>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L2_1: l2-cache { @@ -216,6 +221,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x101>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L1_I_101: l1-icache { @@ -231,6 +237,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x102>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L1_I_102: l1-icache { @@ -246,6 +253,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x103>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L1_I_103: l1-icache { @@ -379,43 +387,43 @@ compatible = "operating-points-v2"; rpmpd_opp_ret: opp1 { - opp-level = <16>; + opp-level = <RPM_SMD_LEVEL_RETENTION>; }; rpmpd_opp_ret_plus: opp2 { - opp-level = <32>; + opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>; }; rpmpd_opp_min_svs: opp3 { - opp-level = <48>; + opp-level = <RPM_SMD_LEVEL_MIN_SVS>; }; rpmpd_opp_low_svs: opp4 { - opp-level = <64>; + opp-level = <RPM_SMD_LEVEL_LOW_SVS>; }; rpmpd_opp_svs: opp5 { - opp-level = <128>; + opp-level = <RPM_SMD_LEVEL_SVS>; }; rpmpd_opp_svs_plus: opp6 { - opp-level = <192>; + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; }; rpmpd_opp_nom: opp7 { - opp-level = <256>; + opp-level = <RPM_SMD_LEVEL_NOM>; }; rpmpd_opp_nom_plus: opp8 { - opp-level = <320>; + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; }; rpmpd_opp_turbo: opp9 { - opp-level = <384>; + opp-level = <RPM_SMD_LEVEL_TURBO>; }; rpmpd_opp_turbo_plus: opp10 { - opp-level = <512>; + opp-level = <RPM_SMD_LEVEL_BINNING>; }; }; }; @@ -937,6 +945,7 @@ num-lanes = <1>; phys = <&pciephy>; phy-names = "pciephy"; + status = "disabled"; ranges = <0x01000000 0x0 0x1b200000 0x1b200000 0x0 0x100000>, <0x02000000 0x0 0x1b300000 0x1b300000 0x0 0xd00000>; @@ -962,11 +971,12 @@ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; }; - phy@1c06000 { + pcie_phy: phy@1c06000 { compatible = "qcom,msm8998-qmp-pcie-phy"; reg = <0x01c06000 0x18c>; #address-cells = <1>; #size-cells = <1>; + status = "disabled"; ranges; clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, @@ -999,6 +1009,7 @@ phy-names = "ufsphy"; lanes-per-direction = <2>; power-domains = <&gcc UFS_GDSC>; + status = "disabled"; #reset-cells = <1>; clock-names = @@ -1038,6 +1049,7 @@ reg = <0x01da7000 0x18c>; #address-cells = <1>; #size-cells = <1>; + status = "disabled"; ranges; clock-names = @@ -1073,6 +1085,278 @@ #gpio-cells = <0x2>; interrupt-controller; #interrupt-cells = <0x2>; + + sdc2_clk_on: sdc2_clk_on { + config { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + }; + + sdc2_clk_off: sdc2_clk_off { + config { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + }; + + sdc2_cmd_on: sdc2_cmd_on { + config { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + }; + + sdc2_cmd_off: sdc2_cmd_off { + config { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_data_on: sdc2_data_on { + config { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + }; + + sdc2_data_off: sdc2_data_off { + config { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_cd_on: sdc2_cd_on { + mux { + pins = "gpio95"; + function = "gpio"; + }; + + config { + pins = "gpio95"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_cd_off: sdc2_cd_off { + mux { + pins = "gpio95"; + function = "gpio"; + }; + + config { + pins = "gpio95"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + blsp1_uart3_on: blsp1_uart3_on { + tx { + pins = "gpio45"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio46"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + + cts { + pins = "gpio47"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + + rfr { + pins = "gpio48"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp1_i2c1_default: blsp1-i2c1-default { + pins = "gpio2", "gpio3"; + function = "blsp_i2c1"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c1_sleep: blsp1-i2c1-sleep { + pins = "gpio2", "gpio3"; + function = "blsp_i2c1"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c2_default: blsp1-i2c2-default { + pins = "gpio32", "gpio33"; + function = "blsp_i2c2"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c2_sleep: blsp1-i2c2-sleep { + pins = "gpio32", "gpio33"; + function = "blsp_i2c2"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c3_default: blsp1-i2c3-default { + pins = "gpio47", "gpio48"; + function = "blsp_i2c3"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c3_sleep: blsp1-i2c3-sleep { + pins = "gpio47", "gpio48"; + function = "blsp_i2c3"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c4_default: blsp1-i2c4-default { + pins = "gpio10", "gpio11"; + function = "blsp_i2c4"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c4_sleep: blsp1-i2c4-sleep { + pins = "gpio10", "gpio11"; + function = "blsp_i2c4"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c5_default: blsp1-i2c5-default { + pins = "gpio87", "gpio88"; + function = "blsp_i2c5"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c5_sleep: blsp1-i2c5-sleep { + pins = "gpio87", "gpio88"; + function = "blsp_i2c5"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c6_default: blsp1-i2c6-default { + pins = "gpio43", "gpio44"; + function = "blsp_i2c6"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c6_sleep: blsp1-i2c6-sleep { + pins = "gpio43", "gpio44"; + function = "blsp_i2c6"; + drive-strength = <2>; + bias-pull-up; + }; + /* 6 interfaces per QUP, BLSP2 indexes are numbered (n)+6 */ + blsp2_i2c1_default: blsp2-i2c1-default { + pins = "gpio55", "gpio56"; + function = "blsp_i2c7"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c1_sleep: blsp2-i2c1-sleep { + pins = "gpio55", "gpio56"; + function = "blsp_i2c7"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c2_default: blsp2-i2c2-default { + pins = "gpio6", "gpio7"; + function = "blsp_i2c8"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c2_sleep: blsp2-i2c2-sleep { + pins = "gpio6", "gpio7"; + function = "blsp_i2c8"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c3_default: blsp2-i2c3-default { + pins = "gpio51", "gpio52"; + function = "blsp_i2c9"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c3_sleep: blsp2-i2c3-sleep { + pins = "gpio51", "gpio52"; + function = "blsp_i2c9"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c4_default: blsp2-i2c4-default { + pins = "gpio67", "gpio68"; + function = "blsp_i2c10"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c4_sleep: blsp2-i2c4-sleep { + pins = "gpio67", "gpio68"; + function = "blsp_i2c10"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c5_default: blsp2-i2c5-default { + pins = "gpio60", "gpio61"; + function = "blsp_i2c11"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c5_sleep: blsp2-i2c5-sleep { + pins = "gpio60", "gpio61"; + function = "blsp_i2c11"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c6_default: blsp2-i2c6-default { + pins = "gpio83", "gpio84"; + function = "blsp_i2c12"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c6_sleep: blsp2-i2c6-sleep { + pins = "gpio83", "gpio84"; + function = "blsp_i2c12"; + drive-strength = <2>; + bias-pull-up; + }; }; remoteproc_mss: remoteproc@4080000 { @@ -1789,6 +2073,11 @@ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c1_default>; + pinctrl-1 = <&blsp1_i2c1_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1804,6 +2093,11 @@ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c2_default>; + pinctrl-1 = <&blsp1_i2c2_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1819,6 +2113,11 @@ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c3_default>; + pinctrl-1 = <&blsp1_i2c3_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1834,6 +2133,11 @@ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c4_default>; + pinctrl-1 = <&blsp1_i2c4_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1849,6 +2153,11 @@ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 14>, <&blsp1_dma 15>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c5_default>; + pinctrl-1 = <&blsp1_i2c5_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1864,6 +2173,11 @@ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 16>, <&blsp1_dma 17>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c6_default>; + pinctrl-1 = <&blsp1_i2c6_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1871,6 +2185,19 @@ #size-cells = <0>; }; + blsp2_dma: dma@c184000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x0c184000 0x25000>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + qcom,controlled-remotely; + num-channels = <18>; + qcom,num-ees = <4>; + }; + blsp2_uart1: serial@c1b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x0c1b0000 0x1000>; @@ -1881,7 +2208,7 @@ status = "disabled"; }; - blsp2_i2c0: i2c@c1b5000 { + blsp2_i2c1: i2c@c1b5000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b5000 0x600>; interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; @@ -1889,6 +2216,11 @@ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c1_default>; + pinctrl-1 = <&blsp2_i2c1_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1896,7 +2228,7 @@ #size-cells = <0>; }; - blsp2_i2c1: i2c@c1b6000 { + blsp2_i2c2: i2c@c1b6000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b6000 0x600>; interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; @@ -1904,6 +2236,11 @@ clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 8>, <&blsp2_dma 9>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c2_default>; + pinctrl-1 = <&blsp2_i2c2_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1911,7 +2248,7 @@ #size-cells = <0>; }; - blsp2_i2c2: i2c@c1b7000 { + blsp2_i2c3: i2c@c1b7000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b7000 0x600>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; @@ -1919,6 +2256,11 @@ clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c3_default>; + pinctrl-1 = <&blsp2_i2c3_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1926,7 +2268,7 @@ #size-cells = <0>; }; - blsp2_i2c3: i2c@c1b8000 { + blsp2_i2c4: i2c@c1b8000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b8000 0x600>; interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; @@ -1934,6 +2276,11 @@ clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 12>, <&blsp2_dma 13>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c4_default>; + pinctrl-1 = <&blsp2_i2c4_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1941,7 +2288,7 @@ #size-cells = <0>; }; - blsp2_i2c4: i2c@c1b9000 { + blsp2_i2c5: i2c@c1b9000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b9000 0x600>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; @@ -1949,6 +2296,11 @@ clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 14>, <&blsp2_dma 15>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c5_default>; + pinctrl-1 = <&blsp2_i2c5_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1956,7 +2308,7 @@ #size-cells = <0>; }; - blsp2_i2c5: i2c@c1ba000 { + blsp2_i2c6: i2c@c1ba000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1ba000 0x600>; interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; @@ -1964,6 +2316,11 @@ clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 16>, <&blsp2_dma 17>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c6_default>; + pinctrl-1 = <&blsp2_i2c6_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2110,5 +2467,3 @@ }; }; }; - -#include "msm8998-pins.dtsi" diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi index a53eccf2b695..bdc76d504b78 100644 --- a/arch/arm64/boot/dts/qcom/pm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi @@ -11,7 +11,7 @@ / { thermal-zones { - pm8150 { + pm8150-thermal { polling-delay-passive = <100>; polling-delay = <0>; @@ -97,6 +97,16 @@ }; }; + pm8150_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pm8150_rtc: rtc@6000 { compatible = "qcom,pm8941-rtc"; reg = <0x6000>; diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi index e112e8876db6..b21e56a46145 100644 --- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi @@ -10,7 +10,7 @@ / { thermal-zones { - pm8150b { + pm8150b-thermal { polling-delay-passive = <100>; polling-delay = <0>; @@ -95,6 +95,16 @@ }; }; + pm8150b_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pm8150b_gpios: gpio@c000 { compatible = "qcom,pm8150b-gpio"; reg = <0xc000>; diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi index 62139538b7d9..52f094a2b713 100644 --- a/arch/arm64/boot/dts/qcom/pm8150l.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi @@ -10,7 +10,7 @@ / { thermal-zones { - pm8150l { + pm8150l-thermal { polling-delay-passive = <100>; polling-delay = <0>; @@ -89,6 +89,16 @@ }; }; + pm8150l_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pm8150l_gpios: gpio@c000 { compatible = "qcom,pm8150l-gpio"; reg = <0xc000>; diff --git a/arch/arm64/boot/dts/qcom/pm8994.dtsi b/arch/arm64/boot/dts/qcom/pm8994.dtsi index 5ffdf37d8e31..c3876c82c874 100644 --- a/arch/arm64/boot/dts/qcom/pm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8994.dtsi @@ -6,7 +6,7 @@ / { thermal-zones { - pm8994 { + pm8994-thermal { polling-delay-passive = <250>; polling-delay = <1000>; @@ -43,7 +43,7 @@ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; }; - pon@800 { + pm8994_pon: pon@800 { compatible = "qcom,pm8916-pon"; reg = <0x800>; diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi index 67283d60e2ac..6f5bb6b37ec2 100644 --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi @@ -9,7 +9,7 @@ / { thermal-zones { - pm8998 { + pm8998-thermal { polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm64/boot/dts/qcom/pmi8998.dtsi b/arch/arm64/boot/dts/qcom/pmi8998.dtsi index d016b12967eb..d230c510d4b7 100644 --- a/arch/arm64/boot/dts/qcom/pmi8998.dtsi +++ b/arch/arm64/boot/dts/qcom/pmi8998.dtsi @@ -30,11 +30,15 @@ compatible = "qcom,pmi8998-lab-ibb"; ibb: ibb { - interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>; + interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>, + <0x3 0xdc 0x0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "sc-err", "ocp"; }; lab: lab { - interrupts = <0x3 0xde 0x0 IRQ_TYPE_EDGE_RISING>; + interrupts = <0x3 0xde 0x1 IRQ_TYPE_EDGE_RISING>, + <0x3 0xde 0x0 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "sc-err", "ocp"; }; }; }; diff --git a/arch/arm64/boot/dts/qcom/pms405.dtsi b/arch/arm64/boot/dts/qcom/pms405.dtsi index ff4005186895..172be177fc8f 100644 --- a/arch/arm64/boot/dts/qcom/pms405.dtsi +++ b/arch/arm64/boot/dts/qcom/pms405.dtsi @@ -8,7 +8,7 @@ / { thermal-zones { - pms405 { + pms405-thermal { polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index ce22d4fa383e..26a4a5a6871e 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -7,6 +7,8 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/sound/qcom,q6afe.h> +#include <dt-bindings/sound/qcom,q6asm.h> #include "sm8250.dtsi" #include "pm8150.dtsi" #include "pm8150b.dtsi" @@ -40,6 +42,17 @@ regulator-always-on; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <<9611_out>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -66,6 +79,98 @@ }; + lt9611_1v2: lt9611-vdd12-regulator { + compatible = "regulator-fixed"; + regulator-name = "LT9611_1V2"; + + vin-supply = <&vdc_3v3>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + lt9611_3v3: lt9611-3v3 { + compatible = "regulator-fixed"; + regulator-name = "LT9611_3V3"; + + vin-supply = <&vdc_3v3>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + thermal-zones { + conn-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150b_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + pm8150l-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 1>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + skin-msm-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 0>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + wifi-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 1>; + + trips { + active-config0 { + temperature = <52000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + xo-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 0>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + }; + vbat: vbat-regulator { compatible = "regulator-fixed"; regulator-name = "VBAT"; @@ -87,7 +192,7 @@ vdc_3v3: vdc-3v3-regulator { compatible = "regulator-fixed"; regulator-name = "VDC_3V3"; - vin-supply = <&dc12v>; + vin-supply = <&vreg_l11c_3p3>; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; @@ -120,6 +225,11 @@ }; }; +&adsp { + status = "okay"; + firmware-name = "qcom/sm8250/adsp.mbn"; +}; + &apps_rsc { pm8009-rpmh-regulators { compatible = "qcom,pm8009-rpmh-regulators"; @@ -406,6 +516,42 @@ }; }; +&cdsp { + status = "okay"; + firmware-name = "qcom/sm8250/cdsp.mbn"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l9a_1p2>; + +#if 0 + qcom,dual-dsi-mode; + qcom,master-dsi; +#endif + + ports { + port@1 { + endpoint { + remote-endpoint = <<9611_a>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l5a_0p88>; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sm8250/a650_zap.mbn"; + }; +}; + /* LS-I2C0 */ &i2c4 { status = "okay"; @@ -413,6 +559,55 @@ &i2c5 { status = "okay"; + clock-frequency = <400000>; + + lt9611_codec: hdmi-bridge@2b { + compatible = "lontium,lt9611uxc"; + reg = <0x2b>; + #sound-dai-cells = <1>; + + interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_HIGH>; + + vdd-supply = <<9611_1v2>; + vcc-supply = <<9611_3v3>; + + pinctrl-names = "default"; + pinctrl-0 = <<9611_irq_pin <9611_rst_pin>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lt9611_a: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + +#if 0 + port@1 { + reg = <1>; + + lt9611_b: endpoint { + remote-endpoint = <&dsi1_out>; + }; + }; +#endif + + port@2 { + reg = <2>; + + lt9611_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + + }; + }; }; /* LS-I2C1 */ @@ -420,6 +615,88 @@ status = "okay"; }; +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&pm8150_adc { + xo-therm@4c { + reg = <ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + wifi-therm@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150_adc_tm { + status = "okay"; + + xo-therm@0 { + reg = <0>; + io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + wifi-therm@1 { + reg = <1>; + io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_default_state>; +}; + +&pcie0_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&pcie1 { + status = "okay"; + perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_default_state>; +}; + +&pcie1_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&pcie2 { + status = "okay"; + perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_default_state>; +}; + +&pcie2_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + &pm8150_gpios { gpio-reserved-ranges = <1 1>, <3 2>, <7 1>; gpio-line-names = @@ -435,6 +712,25 @@ "GPIO_10_P"; /* Green LED */ }; +&pm8150b_adc { + conn-therm@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150b_adc_tm { + status = "okay"; + + conn-therm@0 { + reg = <0>; + io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + &pm8150b_gpios { gpio-line-names = "NC", @@ -451,6 +747,38 @@ "NC"; }; +&pm8150l_adc { + skin-msm-therm@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pm8150l-therm@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150l_adc_tm { + status = "okay"; + + skin-msm-therm@0 { + reg = <0>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + pm8150l-therm@1 { + reg = <1>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + &pm8150l_gpios { gpio-line-names = "NC", @@ -465,6 +793,15 @@ "PM_GPIO-B", "NC", "PM3003A_MODE"; + + lt9611_rst_pin: lt9611-rst-pin { + pins = "gpio5"; + function = "normal"; + + output-high; + input-disable; + power-source = <0>; + }; }; &pm8150_rtc { @@ -483,6 +820,35 @@ status = "okay"; }; +&q6afedai { + qi2s@16 { + reg = <16>; + qcom,sd-lines = <0 1 2 3>; + }; +}; + +/* TERT I2S Uses 1 I2S SD Lines for audio on LT9611 HDMI Bridge */ +&q6afedai { + qi2s@20 { + reg = <20>; + qcom,sd-lines = <0>; + }; +}; + +&q6asmdai { + dai@0 { + reg = <0>; + }; + + dai@1 { + reg = <1>; + }; + + dai@2 { + reg = <2>; + }; +}; + &sdhc_2 { status = "okay"; pinctrl-names = "default"; @@ -491,12 +857,91 @@ vqmmc-supply = <&vreg_l6c_2p96>; cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; bus-width = <4>; - /* there seem to be issues with HS400-1.8V mode, so disable it */ - no-1-8-v; no-sdio; no-emmc; }; +&sound { + compatible = "qcom,qrb5165-rb5-sndcard"; + pinctrl-0 = <&tert_mi2s_active>; + pinctrl-names = "default"; + model = "Qualcomm-RB5-WSA8815-Speakers-DMIC0"; + audio-routing = + "SpkrLeft IN", "WSA_SPK1 OUT", + "SpkrRight IN", "WSA_SPK2 OUT", + "VA DMIC0", "vdd-micb", + "VA DMIC1", "vdd-micb", + "MM_DL1", "MultiMedia1 Playback", + "MM_DL2", "MultiMedia2 Playback", + "MultiMedia3 Capture", "MM_UL3"; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + mm2-dai-link { + link-name = "MultiMedia2"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; + }; + }; + + mm3-dai-link { + link-name = "MultiMedia3"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; + }; + }; + + hdmi-dai-link { + link-name = "HDMI Playback"; + cpu { + sound-dai = <&q6afedai TERTIARY_MI2S_RX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <<9611_codec 0>; + }; + }; + + dma-dai-link { + link-name = "WSA Playback"; + cpu { + sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; + }; + }; + + va-dai-link { + link-name = "VA Capture"; + cpu { + sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&vamacro 0>; + }; + }; +}; + /* CAN */ &spi0 { status = "okay"; @@ -512,6 +957,26 @@ }; }; +&swr0 { + left_spkr: wsa8810-left{ + compatible = "sdw10217211000"; + reg = <0 3>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrLeft"; + #sound-dai-cells = <0>; + }; + + right_spkr: wsa8810-right{ + compatible = "sdw10217211000"; + reg = <0 4>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrRight"; + #sound-dai-cells = <0>; + }; +}; + &tlmm { gpio-reserved-ranges = <40 4>; gpio-line-names = @@ -696,6 +1161,87 @@ "HST_WLAN_UART_TX", "HST_WLAN_UART_RX"; + lt9611_irq_pin: lt9611-irq { + pins = "gpio63"; + function = "gpio"; + bias-disable; + }; + + pcie0_default_state: pcie0-default { + clkreq { + pins = "gpio80"; + function = "pci_e0"; + bias-pull-up; + }; + + reset-n { + pins = "gpio79"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio81"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie1_default_state: pcie1-default { + clkreq { + pins = "gpio83"; + function = "pci_e1"; + bias-pull-up; + }; + + reset-n { + pins = "gpio82"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio84"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie2_default_state: pcie2-default { + clkreq { + pins = "gpio86"; + function = "pci_e2"; + bias-pull-up; + }; + + reset-n { + pins = "gpio85"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio87"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + sdc2_default_state: sdc2-default { clk { pins = "sdc2_clk"; @@ -706,13 +1252,13 @@ cmd { pins = "sdc2_cmd"; bias-pull-up; - drive-strength = <16>; + drive-strength = <10>; }; data { pins = "sdc2_data"; bias-pull-up; - drive-strength = <16>; + drive-strength = <10>; }; }; @@ -792,3 +1338,10 @@ vdda-phy-supply = <&vreg_l9a_1p2>; vdda-pll-supply = <&vreg_l18a_0p92>; }; + +&vamacro { + pinctrl-0 = <&dmic01_active>; + pinctrl-names = "default"; + vdd-micb-supply = <&vreg_s4a_1p8>; + qcom,dmic-sample-rate = <600000>; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 8ed7dd39f6e3..07c8b2c926c0 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -298,40 +298,6 @@ regulator-max-microvolt = <1128000>; }; - /* - * pp2040_s5a (smps5) and pp1056_s4a (smps4) are just - * inputs to other rails on AOP-managed PMICs on trogdor. - * The system is already configured to manage these rails - * automatically (enable when needed, adjust voltage for - * headroom) so we won't specify anything here. - * - * NOTE: though the rails have a voltage implied by their - * name, the automatic headroom calculation might not result - * in them being that voltage. ...and that's OK. - * Specifically the only point of these rails is to provide - * an input source for other rails and if we can satisify the - * needs of those other rails with a lower source voltage then - * we save power. - */ - - pp1200_l1a: ldo1 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - pp1000_l2a: ldo2 { - regulator-min-microvolt = <944000>; - regulator-max-microvolt = <1056000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - pp1000_l3a: ldo3 { - regulator-min-microvolt = <968000>; - regulator-max-microvolt = <1064000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - vdd_qlink_lv: vdd_qlink_lv_ck: vdd_qusb_hs0_core: @@ -350,24 +316,6 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; - pp2700_l5a: ldo5 { - regulator-min-microvolt = <2704000>; - regulator-max-microvolt = <2704000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - ebi0_cal: - ebi1_cal: - vddio_ck_ebi0: - vddio_ck_ebi1: - vddio_ebi0: - vddq: - pp600_l6a: ldo6 { - regulator-min-microvolt = <568000>; - regulator-max-microvolt = <648000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - vdd_cx_wlan: pp800_l9a: ldo9 { regulator-min-microvolt = <488000>; @@ -404,6 +352,11 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + /* + * On trogdor this needs to match l10a since we use it to + * give power to things like SPI flash which communicate back + * on lines powered by l10a. Thus we force to 1.8V. + */ pp1800_l13a: ldo13 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -424,12 +377,6 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; - pp2700_l16a: ldo16 { - regulator-min-microvolt = <2496000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - vdda_qusb_hs0_3p1: vdd_pdphy: pp3100_l17a: ldo17 { @@ -463,8 +410,8 @@ }; pp1800_l1c: ldo1 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1616000>; + regulator-max-microvolt = <1984000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; @@ -491,25 +438,10 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; - ld_pp1800_esim_l4c: - vddpx_5: - pp1800_l4c: ldo4 { - regulator-min-microvolt = <1648000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vddpx_6: - pp1800_l5c: ldo5 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - vddpx_2: ppvar_l6c: ldo6 { regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3304000>; + regulator-max-microvolt = <2952000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; @@ -936,6 +868,13 @@ ap_spi_fp: &spi10 { /* PINCTRL - additions to nodes defined in sc7180.dtsi */ +&dp_hot_plug_det { + pinconf { + pins = "gpio117"; + bias-disable; + }; +}; + &qspi_cs0 { pinconf { pins = "gpio68"; diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 22b832fc62e3..284e0f7bea84 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -682,6 +682,11 @@ reg = <0x25b 0x1>; bits = <1 3>; }; + + gpu_speed_bin: gpu_speed_bin@1d2 { + reg = <0x1d2 0x2>; + bits = <5 8>; + }; }; sdhc_1: sdhci@7c4000 { @@ -1468,12 +1473,6 @@ pins = "gpio117"; function = "dp_hot"; }; - - pinconf { - pins = "gpio117"; - bias-disable; - input-enable; - }; }; qspi_clk: qspi-clk { @@ -2060,52 +2059,69 @@ #cooling-cells = <2>; + nvmem-cells = <&gpu_speed_bin>; + nvmem-cell-names = "speed_bin"; + interconnects = <&gem_noc MASTER_GFX3D 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "gfx-mem"; gpu_opp_table: opp-table { compatible = "operating-points-v2"; + opp-825000000 { + opp-hz = /bits/ 64 <825000000>; + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; + opp-peak-kBps = <8532000>; + opp-supported-hw = <0x04>; + }; + opp-800000000 { opp-hz = /bits/ 64 <800000000>; opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; opp-peak-kBps = <8532000>; + opp-supported-hw = <0x07>; }; opp-650000000 { opp-hz = /bits/ 64 <650000000>; opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; opp-peak-kBps = <7216000>; + opp-supported-hw = <0x07>; }; opp-565000000 { opp-hz = /bits/ 64 <565000000>; opp-level = <RPMH_REGULATOR_LEVEL_NOM>; opp-peak-kBps = <5412000>; + opp-supported-hw = <0x07>; }; opp-430000000 { opp-hz = /bits/ 64 <430000000>; opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; opp-peak-kBps = <5412000>; + opp-supported-hw = <0x07>; }; opp-355000000 { opp-hz = /bits/ 64 <355000000>; opp-level = <RPMH_REGULATOR_LEVEL_SVS>; opp-peak-kBps = <3072000>; + opp-supported-hw = <0x07>; }; opp-267000000 { opp-hz = /bits/ 64 <267000000>; opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; opp-peak-kBps = <3072000>; + opp-supported-hw = <0x07>; }; opp-180000000 { opp-hz = /bits/ 64 <180000000>; opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; opp-peak-kBps = <1804000>; + opp-supported-hw = <0x07>; }; }; }; @@ -3355,6 +3371,7 @@ compatible = "qcom,apss-wdt-sc7180", "qcom,kpss-wdt"; reg = <0 0x17c10000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; }; timer@17c20000{ @@ -3596,7 +3613,7 @@ }; thermal-zones { - cpu0-thermal { + cpu0_thermal: cpu0-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3645,7 +3662,7 @@ }; }; - cpu1-thermal { + cpu1_thermal: cpu1-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3694,7 +3711,7 @@ }; }; - cpu2-thermal { + cpu2_thermal: cpu2-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3743,7 +3760,7 @@ }; }; - cpu3-thermal { + cpu3_thermal: cpu3-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3792,7 +3809,7 @@ }; }; - cpu4-thermal { + cpu4_thermal: cpu4-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3841,7 +3858,7 @@ }; }; - cpu5-thermal { + cpu5_thermal: cpu5-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3890,7 +3907,7 @@ }; }; - cpu6-thermal { + cpu6_thermal: cpu6-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3931,7 +3948,7 @@ }; }; - cpu7-thermal { + cpu7_thermal: cpu7-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3972,7 +3989,7 @@ }; }; - cpu8-thermal { + cpu8_thermal: cpu8-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -4013,7 +4030,7 @@ }; }; - cpu9-thermal { + cpu9_thermal: cpu9-thermal { polling-delay-passive = <250>; polling-delay = <0>; diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index 37d5cc32f6b6..f91a928466c3 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -808,17 +808,19 @@ sdhc_1: sdhci@c0c4000 { compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; reg = <0x0c0c4000 0x1000>, - <0x0c0c5000 0x1000>; - reg-names = "hc", "cqhci"; + <0x0c0c5000 0x1000>, + <0x0c0c8000 0x8000>; + reg-names = "hc", "cqhci", "ice"; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "hc_irq", "pwr_irq"; clocks = <&gcc GCC_SDCC1_APPS_CLK>, - <&gcc GCC_SDCC1_AHB_CLK>, - <&xo_board>; - clock-names = "core", "iface", "xo"; + <&gcc GCC_SDCC1_AHB_CLK>, + <&xo_board>, + <&gcc GCC_SDCC1_ICE_CORE_CLK>; + clock-names = "core", "iface", "xo", "ice"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts index 7cc236575ee2..f749672c5fdc 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts @@ -1112,11 +1112,11 @@ reg = <0x10>; // CAM0_RST_N - reset-gpios = <&tlmm 9 0>; + reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&cam0_default>; gpios = <&tlmm 13 0>, - <&tlmm 9 0>; + <&tlmm 9 GPIO_ACTIVE_LOW>; clocks = <&clock_camcc CAM_CC_MCLK0_CLK>; clock-names = "xvclk"; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi new file mode 100644 index 000000000000..8f617f7b6d34 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi @@ -0,0 +1,623 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "sdm845.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" + +/delete-node/ &rmtfs_mem; + +/ { + aliases { + hsuart0 = &uart6; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "Volume keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_down_gpio &volume_up_gpio>; + + vol-down { + label = "Volume down"; + linux,code = <KEY_VOLUMEDOWN>; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + + vol-up { + label = "Volume up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + }; + + reserved-memory { + /* + * The rmtfs memory region in downstream is 'dynamically allocated' + * but given the same address every time. Hard code it as this address is + * where the modem firmware expects it to be. + */ + rmtfs_mem: memory@f5b01000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xf5b01000 0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + /* + * It seems like reserving the old rmtfs_mem region is also needed to prevent + * random crashes which are most likely modem related, more testing needed. + */ + removed_region: memory@88f00000 { + no-map; + reg = <0 0x88f00000 0 0x200000>; + }; + + ramoops: ramoops@ac300000 { + compatible = "ramoops"; + reg = <0 0xac300000 0 0x400000>; + record-size = <0x40000>; + console-size = <0x40000>; + ftrace-size = <0x40000>; + pmsg-size = <0x200000>; + devinfo-size = <0x1000>; + ecc-size = <16>; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + /* + * The touchscreen regulator seems to be controlled somehow by a gpio. + * Model it as a fixed regulator and keep it on. Without schematics we + * don't know how this is actually wired up... + */ + ts_1p8_supply: ts-1p8-regulator { + compatible = "regulator-fixed"; + regulator-name = "ts_1p8_supply"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 88 0>; + enable-active-high; + regulator-boot-on; + }; +}; + +&adsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/adsp.mbn"; +}; + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + vdd-s13-supply = <&vph_pwr>; + vdd-l1-l27-supply = <&vreg_s7a_1p025>; + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; + vdd-l3-l11-supply = <&vreg_s7a_1p025>; + vdd-l4-l5-supply = <&vreg_s7a_1p025>; + vdd-l6-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; + vdd-l9-supply = <&vreg_bob>; + vdd-l10-l23-l25-supply = <&vreg_bob>; + vdd-l13-l19-l21-supply = <&vreg_bob>; + vdd-l16-l28-supply = <&vreg_bob>; + vdd-l18-l22-supply = <&vreg_bob>; + vdd-l20-l24-supply = <&vreg_bob>; + vdd-l26-supply = <&vreg_s3a_1p35>; + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s5a_2p04: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdda_mipi_dsi0_pll: + vdda_qlink_lv: + vdda_ufs1_core: + vdda_usb1_ss_core: + vreg_l1a_0p875: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l5a_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_1p8: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l17a_1p3: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l20a_2p95: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_3p1: + vreg_l24a_3p075: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l25a_3p3: ldo25 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_mipi_dsi0_1p2: + vdda_ufs1_1p2: + vreg_l26a_1p2: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l28a_3p0: ldo28 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pmi8998-rpmh-regulators { + compatible = "qcom,pmi8998-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s3c_0p6: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +&cdsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + /* + * Both devices use different panels but all other properties + * are common. Compatible line is declared in device dts. + */ + display_panel: panel@0 { + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vddio-supply = <&vreg_l14a_1p88>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +&gcc { + protected-clocks = <GCC_QSPI_CORE_CLK>, + <GCC_QSPI_CORE_CLK_SRC>, + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <GCC_LPASS_Q6_AXI_CLK>, + <GCC_LPASS_SWAY_CLK>; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn"; + }; +}; + +&i2c12 { + status = "okay"; + clock-frequency = <400000>; + + synaptics-rmi4-i2c@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_default_pins>; + + vdd-supply = <&vreg_l28a_3p0>; + vio-supply = <&ts_1p8_supply>; + + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <200>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <144>; + syna,sensor-type = <1>; + syna,rezero-wait-ms = <200>; + }; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +/* Modem/wifi*/ +&mss_pil { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn"; +}; + +&pm8998_gpio { + volume_down_gpio: pm8998_gpio5 { + pinconf { + pins = "gpio5"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; + + volume_up_gpio: pm8998_gpio6 { + pinconf { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qup_i2c12_default { + mux { + pins = "gpio49", "gpio50"; + function = "qup12"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_i2c10_default { + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +/* + * Prevent garbage data on bluetooth UART lines + */ +&qup_uart6_default { + pinmux { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "qup6"; + }; + + cts { + pins = "gpio45"; + bias-pull-down; + }; + + rts-tx { + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio48"; + bias-pull-up; + }; +}; + +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + /* + * This path is relative to the qca/ + * subdir under lib/firmware. + */ + firmware-name = "oneplus6/crnv21.bin"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l20a_2p95>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* + * disable USB3 clock requirement as the device only supports + * USB2. + */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * We don't have the capability to switch modes yet. + */ + dr_mode = "peripheral"; + + /* fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + /* Remove USB3 phy as it's unused on this device. */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + tri_state_key_default: tri_state_key_default { + mux { + pins = "gpio40", "gpio42", "gpio26"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + }; + + ts_default_pins: ts-int { + mux { + pins = "gpio99", "gpio125"; + function = "gpio"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + panel_reset_pins: panel-reset { + mux { + pins = "gpio6", "gpio25", "gpio26"; + function = "gpio"; + drive-strength = <8>; + bias-disable = <0>; + }; + }; + + panel_te_pin: panel-te { + mux { + pins = "gpio10"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + }; + + panel_esd_pin: panel-esd { + mux { + pins = "gpio30"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + input-enable; + }; + }; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + + qcom,snoc-host-cap-8bit-quirk; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts new file mode 100644 index 000000000000..72842c887617 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6 (enchilada) device tree. + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6"; + compatible = "oneplus,enchilada", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,sofef00"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts new file mode 100644 index 000000000000..969b36dc9e2c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6T (fajita) device tree. + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6T"; + compatible = "oneplus,fajita", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,s6e3fc2x01"; +}; + +&rmi4_f12 { + touchscreen-y-mm = <148>; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi index bcf888381f14..2da77e16f1b3 100644 --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi @@ -4573,6 +4573,7 @@ compatible = "qcom,apss-wdt-sdm845", "qcom,kpss-wdt"; reg = <0 0x17980000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; }; apss_shared: mailbox@17990000 { diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts index 13fdd02cffe6..94705d02f46c 100644 --- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts +++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts @@ -13,7 +13,7 @@ #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include <dt-bindings/sound/qcom,q6afe.h> #include <dt-bindings/sound/qcom,q6asm.h> -#include "sdm845.dtsi" +#include "sdm850.dtsi" #include "pm8998.dtsi" / { diff --git a/arch/arm64/boot/dts/qcom/sdm850.dtsi b/arch/arm64/boot/dts/qcom/sdm850.dtsi new file mode 100644 index 000000000000..b1c2cf566c7a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm850.dtsi @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM850 SoC device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845.dtsi" + +&cpu4_opp_table { + cpu4_opp33: opp-2841600000 { + opp-hz = /bits/ 64 <2841600000>; + opp-peak-kBps = <7216000 25497600>; + }; + + cpu4_opp34: opp-2956800000 { + opp-hz = /bits/ 64 <2956800000>; + opp-peak-kBps = <7216000 25497600>; + turbo-mode; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 5270bda7418f..e5bb17bc2f46 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -47,8 +47,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x0>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD0>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_0: l2-cache { compatible = "cache"; @@ -64,8 +68,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x100>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD1>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_100: l2-cache { compatible = "cache"; @@ -79,8 +87,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x200>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD2>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_200: l2-cache { compatible = "cache"; @@ -93,8 +105,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x300>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD3>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_300: l2-cache { compatible = "cache"; @@ -107,8 +123,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x400>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <369>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; + power-domains = <&CPU_PD4>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_400: l2-cache { compatible = "cache"; @@ -121,8 +141,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x500>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <369>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; + power-domains = <&CPU_PD5>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_500: l2-cache { compatible = "cache"; @@ -135,8 +159,12 @@ compatible = "qcom,kryo485"; reg = <0x0 0x600>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <369>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; + power-domains = <&CPU_PD6>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_600: l2-cache { compatible = "cache"; @@ -149,14 +177,90 @@ compatible = "qcom,kryo485"; reg = <0x0 0x700>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <421>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; + power-domains = <&CPU_PD7>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_700: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; }; }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + + core2 { + cpu = <&CPU2>; + }; + + core3 { + cpu = <&CPU3>; + }; + + core4 { + cpu = <&CPU4>; + }; + + core5 { + cpu = <&CPU5>; + }; + + core6 { + cpu = <&CPU6>; + }; + + core7 { + cpu = <&CPU7>; + }; + }; + }; + + idle-states { + entry-method = "psci"; + + LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + idle-state-name = "little-rail-power-collapse"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <355>; + exit-latency-us = <909>; + min-residency-us = <3934>; + local-timer-stop; + }; + + BIG_CPU_SLEEP_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + idle-state-name = "big-rail-power-collapse"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <241>; + exit-latency-us = <1461>; + min-residency-us = <4488>; + local-timer-stop; + }; + }; + + domain-idle-states { + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "domain-idle-state"; + idle-state-name = "cluster-power-collapse"; + arm,psci-suspend-param = <0x4100c244>; + entry-latency-us = <3263>; + exit-latency-us = <6562>; + min-residency-us = <9987>; + local-timer-stop; + }; + }; }; firmware { @@ -186,6 +290,59 @@ psci { compatible = "arm,psci-1.0"; method = "smc"; + + CPU_PD0: cpu0 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD1: cpu1 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD2: cpu2 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD3: cpu3 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD4: cpu4 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD5: cpu5 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD6: cpu6 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD7: cpu7 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CLUSTER_PD: cpu-cluster0 { + #power-domain-cells = <0>; + domain-idle-states = <&CLUSTER_SLEEP_0>; + }; }; reserved-memory { @@ -1818,6 +1975,7 @@ compatible = "qcom,apss-wdt-sm8150", "qcom,kpss-wdt"; reg = <0 0x17c10000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; }; timer@17c20000 { diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts index dea00f19711d..5b4c5b08434c 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts @@ -24,6 +24,106 @@ stdout-path = "serial0:115200n8"; }; + thermal-zones { + camera-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + conn-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150b_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + mmw-pa1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 2>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + mmw-pa2-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 2>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + skin-msm-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 1>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + skin-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 1>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + xo-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + }; + vph_pwr: vph-pwr-regulator { compatible = "regulator-fixed"; regulator-name = "vph_pwr"; @@ -186,6 +286,13 @@ regulator-max-microvolt = <3008000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + + vreg_l18a_0p9: ldo18 { + regulator-name = "vreg_l18a_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; }; pm8150l-rpmh-regulators { @@ -358,6 +465,13 @@ firmware-name = "qcom/sm8250/cdsp.mbn"; }; +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sm8250/a650_zap.mbn"; + }; +}; + &i2c1 { status = "okay"; clock-frequency = <1000000>; @@ -378,6 +492,115 @@ /* rtc6226 @ 64 */ }; +&pm8150_adc { + xo-therm@4c { + reg = <ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + skin-therm@4d { + reg = <ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pa-therm1@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150_adc_tm { + status = "okay"; + + xo-therm@0 { + reg = <0>; + io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + skin-therm@1 { + reg = <1>; + io-channels = <&pm8150_adc ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + pa-therm1@2 { + reg = <2>; + io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm8150b_adc { + conn-therm@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150b_adc_tm { + status = "okay"; + + conn-therm@0 { + reg = <0>; + io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm8150l_adc_tm { + status = "okay"; + + camera-flash-therm@0 { + reg = <0>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + skin-msm-therm@1 { + reg = <1>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + pa-therm2@2 { + reg = <2>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm8150l_adc { + camera-flash-therm@4d { + reg = <ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + skin-msm-therm@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pa-therm2@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + &pm8150_rtc { status = "okay"; }; @@ -426,3 +649,49 @@ vdda-pll-supply = <&vreg_l9a_1p2>; vdda-pll-max-microamp = <19000>; }; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5a_0p875>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l2a_3p1>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l9a_1p2>; + vdda-pll-supply = <&vreg_l18a_0p9>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5a_0p875>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l2a_3p1>; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l9a_1p2>; + vdda-pll-supply = <&vreg_l18a_0p9>; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 65acd1f381eb..947e1accae3a 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -4,14 +4,18 @@ */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,dispcc-sm8250.h> #include <dt-bindings/clock/qcom,gcc-sm8250.h> #include <dt-bindings/clock/qcom,gpucc-sm8250.h> #include <dt-bindings/clock/qcom,rpmh.h> #include <dt-bindings/interconnect/qcom,osm-l3.h> +#include <dt-bindings/interconnect/qcom,sm8250.h> #include <dt-bindings/mailbox/qcom-ipcc.h> #include <dt-bindings/power/qcom-aoss-qmp.h> #include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,apr.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/sound/qcom,q6afe.h> #include <dt-bindings/thermal/thermal.h> / { @@ -89,6 +93,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x0>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -106,6 +112,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x100>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -120,6 +128,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x200>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -134,6 +144,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x300>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -148,6 +160,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x400>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <379>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -162,6 +176,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x500>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <379>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -177,6 +193,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x600>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <379>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -191,6 +209,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x700>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <444>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; #cooling-cells = <2>; @@ -199,6 +219,42 @@ next-level-cache = <&L3_0>; }; }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + + core2 { + cpu = <&CPU2>; + }; + + core3 { + cpu = <&CPU3>; + }; + + core4 { + cpu = <&CPU4>; + }; + + core5 { + cpu = <&CPU5>; + }; + + core6 { + cpu = <&CPU6>; + }; + + core7 { + cpu = <&CPU7>; + }; + }; + }; }; firmware { @@ -214,6 +270,13 @@ reg = <0x0 0x80000000 0x0 0x0>; }; + mmcx_reg: mmcx-reg { + compatible = "regulator-fixed-domain"; + power-domains = <&rpmhpd SM8250_MMCX>; + required-opps = <&rpmhpd_opp_low_svs>; + regulator-name = "MMCX"; + }; + pmu { compatible = "arm,armv8-pmuv3"; interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; @@ -321,7 +384,7 @@ }; }; - smem: qcom,smem { + smem { compatible = "qcom,smem"; memory-region = <&smem_mem>; hwlocks = <&tcsr_mutex 3>; @@ -1168,6 +1231,299 @@ qcom,bcm-voters = <&apps_bcm_voter>; }; + pcie0: pci@1c00000 { + compatible = "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c00000 0 0x3000>, + <0 0x60000000 0 0xf1d>, + <0 0x60000f20 0 0xa8>, + <0 0x60001000 0 0x1000>, + <0 0x60100000 0 0x100000>; + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>, + <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>; + + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>, + <&gcc GCC_PCIE_0_AUX_CLK>, + <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>; + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "tbu", + "ddrss_sf_tbu"; + + iommus = <&apps_smmu 0x1c00 0x7f>; + iommu-map = <0x0 &apps_smmu 0x1c00 0x1>, + <0x100 &apps_smmu 0x1c01 0x1>; + + resets = <&gcc GCC_PCIE_0_BCR>; + reset-names = "pci"; + + power-domains = <&gcc PCIE_0_GDSC>; + + phys = <&pcie0_lane>; + phy-names = "pciephy"; + + status = "disabled"; + }; + + pcie0_phy: phy@1c06000 { + compatible = "qcom,sm8250-qmp-gen3x1-pcie-phy"; + reg = <0 0x01c06000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_WIFI_CLKREF_EN>, + <&gcc GCC_PCIE0_PHY_REFGEN_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_0_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie0_lane: lanes@1c06200 { + reg = <0 0x1c06200 0 0x170>, /* tx */ + <0 0x1c06400 0 0x200>, /* rx */ + <0 0x1c06800 0 0x1f0>, /* pcs */ + <0 0x1c06c00 0 0xf4>; /* "pcs_lane" same as pcs_misc? */ + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + clock-output-names = "pcie_0_pipe_clk"; + }; + }; + + pcie1: pci@1c08000 { + compatible = "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c08000 0 0x3000>, + <0 0x40000000 0 0xf1d>, + <0 0x40000f20 0 0xa8>, + <0 0x40001000 0 0x1000>, + <0 0x40100000 0 0x100000>; + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <1>; + bus-range = <0x00 0xff>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; + + interrupts = <GIC_SPI 306 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, + <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, + <&gcc GCC_PCIE_WIGIG_CLKREF_EN>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>; + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "ref", + "tbu", + "ddrss_sf_tbu"; + + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; + assigned-clock-rates = <19200000>; + + iommus = <&apps_smmu 0x1c80 0x7f>; + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, + <0x100 &apps_smmu 0x1c81 0x1>; + + resets = <&gcc GCC_PCIE_1_BCR>; + reset-names = "pci"; + + power-domains = <&gcc PCIE_1_GDSC>; + + phys = <&pcie1_lane>; + phy-names = "pciephy"; + + status = "disabled"; + }; + + pcie1_phy: phy@1c0e000 { + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; + reg = <0 0x01c0e000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_WIGIG_CLKREF_EN>, + <&gcc GCC_PCIE1_PHY_REFGEN_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_1_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie1_lane: lanes@1c0e200 { + reg = <0 0x1c0e200 0 0x170>, /* tx0 */ + <0 0x1c0e400 0 0x200>, /* rx0 */ + <0 0x1c0ea00 0 0x1f0>, /* pcs */ + <0 0x1c0e600 0 0x170>, /* tx1 */ + <0 0x1c0e800 0 0x200>, /* rx1 */ + <0 0x1c0ee00 0 0xf4>; /* "pcs_com" same as pcs_misc? */ + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + clock-output-names = "pcie_1_pipe_clk"; + }; + }; + + pcie2: pci@1c10000 { + compatible = "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c10000 0 0x3000>, + <0 0x64000000 0 0xf1d>, + <0 0x64000f20 0 0xa8>, + <0 0x64001000 0 0x1000>, + <0 0x64100000 0 0x100000>; + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <2>; + bus-range = <0x00 0xff>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x64200000 0x0 0x64200000 0x0 0x100000>, + <0x02000000 0x0 0x64300000 0x0 0x64300000 0x0 0x3d00000>; + + interrupts = <GIC_SPI 236 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 290 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 415 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 416 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 417 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_PCIE_2_PIPE_CLK>, + <&gcc GCC_PCIE_2_AUX_CLK>, + <&gcc GCC_PCIE_2_CFG_AHB_CLK>, + <&gcc GCC_PCIE_2_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_2_SLV_AXI_CLK>, + <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>, + <&gcc GCC_PCIE_MDM_CLKREF_EN>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>; + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "ref", + "tbu", + "ddrss_sf_tbu"; + + assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>; + assigned-clock-rates = <19200000>; + + iommus = <&apps_smmu 0x1d00 0x7f>; + iommu-map = <0x0 &apps_smmu 0x1d00 0x1>, + <0x100 &apps_smmu 0x1d01 0x1>; + + resets = <&gcc GCC_PCIE_2_BCR>; + reset-names = "pci"; + + power-domains = <&gcc PCIE_2_GDSC>; + + phys = <&pcie2_lane>; + phy-names = "pciephy"; + + status = "disabled"; + }; + + pcie2_phy: phy@1c16000 { + compatible = "qcom,sm8250-qmp-modem-pcie-phy"; + reg = <0 0x1c16000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_2_CFG_AHB_CLK>, + <&gcc GCC_PCIE_MDM_CLKREF_EN>, + <&gcc GCC_PCIE2_PHY_REFGEN_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_2_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie2_lane: lanes@1c0e200 { + reg = <0 0x1c16200 0 0x170>, /* tx0 */ + <0 0x1c16400 0 0x200>, /* rx0 */ + <0 0x1c16a00 0 0x1f0>, /* pcs */ + <0 0x1c16600 0 0x170>, /* tx1 */ + <0 0x1c16800 0 0x200>, /* rx1 */ + <0 0x1c16e00 0 0xf4>; /* "pcs_com" same as pcs_misc? */ + clocks = <&gcc GCC_PCIE_2_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + clock-output-names = "pcie_2_pipe_clk"; + }; + }; + ufs_mem_hc: ufshc@1d84000 { compatible = "qcom,sm8250-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; @@ -1253,15 +1609,169 @@ #hwlock-cells = <1>; }; + wsamacro: codec@3240000 { + compatible = "qcom,sm8250-lpass-wsa-macro"; + reg = <0 0x03240000 0 0x1000>; + clocks = <&audiocc 1>, + <&audiocc 0>, + <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&aoncc 0>, + <&vamacro>; + + clock-names = "mclk", "npl", "macro", "dcodec", "va", "fsgen"; + + #clock-cells = <0>; + clock-frequency = <9600000>; + clock-output-names = "mclk"; + #sound-dai-cells = <1>; + + pinctrl-names = "default"; + pinctrl-0 = <&wsa_swr_active>; + }; + + swr0: soundwire-controller@3250000 { + reg = <0 0x03250000 0 0x2000>; + compatible = "qcom,soundwire-v1.5.1"; + interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&wsamacro>; + clock-names = "iface"; + + qcom,din-ports = <2>; + qcom,dout-ports = <6>; + + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>; + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>; + qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>; + qcom,ports-block-pack-mode = /bits/ 8 <0x0 0x0 0x1 0x0 0x0 0x1 0x0 0x0>; + + #sound-dai-cells = <1>; + #address-cells = <2>; + #size-cells = <0>; + }; + + audiocc: clock-controller@3300000 { + compatible = "qcom,sm8250-lpass-audiocc"; + reg = <0 0x03300000 0 0x30000>; + #clock-cells = <1>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio", "bus"; + }; + + vamacro: codec@3370000 { + compatible = "qcom,sm8250-lpass-va-macro"; + reg = <0 0x03370000 0 0x1000>; + clocks = <&aoncc 0>, + <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + + clock-names = "mclk", "macro", "dcodec"; + + #clock-cells = <0>; + clock-frequency = <9600000>; + clock-output-names = "fsgen"; + #sound-dai-cells = <1>; + }; + + aoncc: clock-controller@3380000 { + compatible = "qcom,sm8250-lpass-aoncc"; + reg = <0 0x03380000 0 0x40000>; + #clock-cells = <1>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio", "bus"; + }; + + lpass_tlmm: pinctrl@33c0000{ + compatible = "qcom,sm8250-lpass-lpi-pinctrl"; + reg = <0 0x033c0000 0x0 0x20000>, + <0 0x03550000 0x0 0x10000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&lpass_tlmm 0 0 14>; + + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio"; + + wsa_swr_active: wsa-swr-active-pins { + clk { + pins = "gpio10"; + function = "wsa_swr_clk"; + drive-strength = <2>; + slew-rate = <1>; + bias-disable; + }; + + data { + pins = "gpio11"; + function = "wsa_swr_data"; + drive-strength = <2>; + slew-rate = <1>; + bias-bus-hold; + + }; + }; + + wsa_swr_sleep: wsa-swr-sleep-pins { + clk { + pins = "gpio10"; + function = "wsa_swr_clk"; + drive-strength = <2>; + input-enable; + bias-pull-down; + }; + + data { + pins = "gpio11"; + function = "wsa_swr_data"; + drive-strength = <2>; + input-enable; + bias-pull-down; + + }; + }; + + dmic01_active: dmic01-active-pins { + clk { + pins = "gpio6"; + function = "dmic1_clk"; + drive-strength = <8>; + output-high; + }; + data { + pins = "gpio7"; + function = "dmic1_data"; + drive-strength = <8>; + input-enable; + }; + }; + + dmic01_sleep: dmic01-sleep-pins { + clk { + pins = "gpio6"; + function = "dmic1_clk"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + data { + pins = "gpio7"; + function = "dmic1_data"; + drive-strength = <2>; + pull-down; + input-enable; + }; + }; + }; + gpu: gpu@3d00000 { - /* - * note: the amd,imageon compatible makes it possible - * to use the drm/msm driver without the display node, - * make sure to remove it when display node is added - */ compatible = "qcom,adreno-650.2", - "qcom,adreno", - "amd,imageon"; + "qcom,adreno"; #stream-id-cells = <16>; reg = <0 0x03d00000 0 0x40000>; @@ -1557,6 +2067,9 @@ }; }; + sound: sound { + }; + usb_1_hsphy: phy@88e3000 { compatible = "qcom,sm8250-usb-hs-phy", "qcom,usb-snps-hs-7nm-phy"; @@ -1657,7 +2170,7 @@ clocks = <&gcc GCC_SDCC2_AHB_CLK>, <&gcc GCC_SDCC2_APPS_CLK>, - <&xo_board>; + <&rpmhcc RPMH_CXO_CLK>; clock-names = "iface", "core", "xo"; iommus = <&apps_smmu 0x4a0 0x0>; qcom,dll-config = <0x0007642c>; @@ -1758,6 +2271,12 @@ }; }; + system-cache-controller@9200000 { + compatible = "qcom,sm8250-llcc"; + reg = <0 0x09200000 0 0x1d0000>, <0 0x09600000 0 0x50000>; + reg-names = "llcc_base", "llcc_broadcast_base"; + }; + usb_2: usb@a8f8800 { compatible = "qcom,sm8250-dwc3", "qcom,dwc3"; reg = <0 0x0a8f8800 0 0x400>; @@ -1803,6 +2322,299 @@ }; }; + mdss: mdss@ae00000 { + compatible = "qcom,sdm845-mdss"; + reg = <0 0x0ae00000 0 0x1000>; + reg-names = "mdss"; + + interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, + <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, + <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; + + power-domains = <&dispcc MDSS_GDSC>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "nrt_bus", "core"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>; + assigned-clock-rates = <460000000>; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x820 0x402>; + + status = "disabled"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + mdss_mdp: mdp@ae01000 { + compatible = "qcom,sdm845-dpu"; + reg = <0 0x0ae01000 0 0x8f000>, + <0 0x0aeb0000 0 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "iface", "bus", "core", "vsync"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <460000000>, + <19200000>; + + operating-points-v2 = <&mdp_opp_table>; + power-domains = <&rpmhpd SM8250_MMCX>; + + interrupt-parent = <&mdss>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + }; + + mdp_opp_table: mdp-opp-table { + compatible = "operating-points-v2"; + + opp-200000000 { + opp-hz = /bits/ 64 <200000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-345000000 { + opp-hz = /bits/ 64 <345000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-460000000 { + opp-hz = /bits/ 64 <460000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + dsi0: dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae94000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8250_MMCX>; + + phys = <&dsi0_phy>; + phy-names = "dsi"; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + }; + + dsi0_phy: dsi-phy@ae94400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae94400 0 0x200>, + <0 0x0ae94600 0 0x280>, + <0 0x0ae94900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + }; + + dsi1: dsi@ae96000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae96000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, + <&dispcc DISP_CC_MDSS_ESC1_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8250_MMCX>; + + phys = <&dsi1_phy>; + phy-names = "dsi"; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi1_in: endpoint { + remote-endpoint = <&dpu_intf2_out>; + }; + }; + + port@1 { + reg = <1>; + dsi1_out: endpoint { + }; + }; + }; + }; + + dsi1_phy: dsi-phy@ae96400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae96400 0 0x200>, + <0 0x0ae96600 0 0x280>, + <0 0x0ae96900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + + dsi_opp_table: dsi-opp-table { + compatible = "operating-points-v2"; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-358000000 { + opp-hz = /bits/ 64 <358000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; + }; + + dispcc: clock-controller@af00000 { + compatible = "qcom,sm8250-dispcc"; + reg = <0 0x0af00000 0 0x20000>; + mmcx-supply = <&mmcx_reg>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&dsi0_phy 0>, + <&dsi0_phy 1>, + <&dsi1_phy 0>, + <&dsi1_phy 1>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <&sleep_clk>; + clock-names = "bi_tcxo", + "dsi0_phy_pll_out_byteclk", + "dsi0_phy_pll_out_dsiclk", + "dsi1_phy_pll_out_byteclk", + "dsi1_phy_pll_out_dsiclk", + "dp_link_clk_divsel_ten", + "dp_vco_divided_clk_src_mux", + "dptx1_phy_pll_link_clk", + "dptx1_phy_pll_vco_div_clk", + "dptx2_phy_pll_link_clk", + "dptx2_phy_pll_vco_div_clk", + "edp_phy_pll_link_clk", + "edp_phy_pll_vco_div_clk", + "sleep_clk"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + pdc: interrupt-controller@b220000 { compatible = "qcom,sm8250-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; @@ -1880,6 +2692,37 @@ gpio-ranges = <&tlmm 0 0 180>; wakeup-parent = <&pdc>; + pri_mi2s_active: pri-mi2s-active { + sclk { + pins = "gpio138"; + function = "mi2s0_sck"; + drive-strength = <8>; + bias-disable; + }; + + ws { + pins = "gpio141"; + function = "mi2s0_ws"; + drive-strength = <8>; + output-high; + }; + + data0 { + pins = "gpio139"; + function = "mi2s0_data0"; + drive-strength = <8>; + bias-disable; + output-high; + }; + + data1 { + pins = "gpio140"; + function = "mi2s0_data1"; + drive-strength = <8>; + output-high; + }; + }; + qup_i2c0_default: qup-i2c0-default { mux { pins = "gpio28", "gpio29"; @@ -2476,6 +3319,30 @@ function = "qup18"; }; }; + + tert_mi2s_active: tert-mi2s-active { + sck { + pins = "gpio133"; + function = "mi2s2_sck"; + drive-strength = <8>; + bias-disable; + }; + + data0 { + pins = "gpio134"; + function = "mi2s2_data0"; + drive-strength = <8>; + bias-disable; + output-high; + }; + + ws { + pins = "gpio135"; + function = "mi2s2_ws"; + drive-strength = <8>; + output-high; + }; + }; }; apps_smmu: iommu@15000000 { @@ -2620,6 +3487,60 @@ label = "lpass"; qcom,remote-pid = <2>; + apr { + compatible = "qcom,apr-v2"; + qcom,glink-channels = "apr_audio_svc"; + qcom,apr-domain = <APR_DOMAIN_ADSP>; + #address-cells = <1>; + #size-cells = <0>; + + apr-service@3 { + reg = <APR_SVC_ADSP_CORE>; + compatible = "qcom,q6core"; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + }; + + q6afe: apr-service@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + q6afedai: dais { + compatible = "qcom,q6afe-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + }; + + q6afecc: cc { + compatible = "qcom,q6afe-clocks"; + #clock-cells = <2>; + }; + }; + + q6asm: apr-service@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + q6asmdai: dais { + compatible = "qcom,q6asm-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + iommus = <&apps_smmu 0x1801 0x0>; + }; + }; + + q6adm: apr-service@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + q6routing: routing { + compatible = "qcom,q6adm-routing"; + #sound-dai-cells = <0>; + }; + }; + }; + fastrpc { compatible = "qcom,fastrpc"; qcom,glink-channels = "fastrpcglink-apps-dsp"; @@ -2661,6 +3582,7 @@ compatible = "qcom,apss-wdt-sm8250", "qcom,kpss-wdt"; reg = <0 0x17c10000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; }; timer@17c20000 { diff --git a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts new file mode 100644 index 000000000000..8923657579fb --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Linaro Limited + */ + +/dts-v1/; + +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sm8350.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. sm8350 MTP"; + compatible = "qcom,sm8350-mtp", "qcom,sm8350"; + + aliases { + serial0 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + pm8350-rpmh-regulators { + compatible = "qcom,pm8350-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + + vdd-l1-l4-supply = <&vreg_s11b_0p95>; + vdd-l2-l7-supply = <&vreg_bob>; + vdd-l3-l5-supply = <&vreg_bob>; + vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>; + vdd-l8-supply = <&vreg_s2c_0p8>; + + vreg_s10b_1p8: smps10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_s11b_0p95: smps11 { + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_s12b_1p25: smps12 { + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1360000>; + }; + + vreg_l1b_0p88: ldo1 { + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p07: ldo2 { + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3b_0p9: ldo3 { + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_0p88: ldo5 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <888000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p2: ldo6 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1208000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b_2p96: ldo7 { + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_1p2: ldo9 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8350c-rpmh-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + + vdd-l1-l12-supply = <&vreg_s1c_1p86>; + vdd-l2-l8-supply = <&vreg_s1c_1p86>; + vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; + vdd-l6-l9-l11-supply = <&vreg_bob>; + vdd-l10-supply = <&vreg_s12b_1p25>; + + vdd-bob-supply = <&vph_pwr>; + + vreg_s1c_1p86: smps1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1952000>; + }; + + vreg_s2c_0p8: smps2 { + regulator-min-microvolt = <640000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_s10c_1p05: smps10 { + regulator-min-microvolt = <1048000>; + regulator-max-microvolt = <1128000>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_1p8: ldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_3p0: ldo3 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c_uim1: ldo4 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5c_uim2: ldo5 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c_1p8: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p96: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_1p2: ldo10 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_2p96: ldo11 { + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12c_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13c_3p0: ldo13 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <52 8>; +}; + +&uart2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi new file mode 100644 index 000000000000..5ef460458f5c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -0,0 +1,499 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Linaro Limaited + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/mailbox/qcom-ipcc.h> +#include <dt-bindings/power/qcom-aoss-qmp.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8350", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x80000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@80000000 { + reg = <0x0 0x80000000 0x0 0x600000>; + no-map; + }; + + xbl_aop_mem: memory@80700000 { + no-map; + reg = <0x0 0x80700000 0x0 0x160000>; + }; + + cmd_db: memory@80860000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x80860000 0x0 0x20000>; + no-map; + }; + + reserved_xbl_uefi_log: memory@80880000 { + reg = <0x0 0x80880000 0x0 0x14000>; + no-map; + }; + + smem_mem: memory@80900000 { + reg = <0x0 0x80900000 0x0 0x200000>; + no-map; + }; + + cpucp_fw_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@80c00000 { + reg = <0x0 0x80c00000 0x0 0x4600000>; + no-map; + }; + + pil_camera_mem: mmeory@85200000 { + reg = <0x0 0x85200000 0x0 0x500000>; + no-map; + }; + + pil_video_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x500000>; + no-map; + }; + + pil_cvp_mem: memory@85c00000 { + reg = <0x0 0x85c00000 0x0 0x500000>; + no-map; + }; + + pil_adsp_mem: memory@86100000 { + reg = <0x0 0x86100000 0x0 0x2100000>; + no-map; + }; + + pil_slpi_mem: memory@88200000 { + reg = <0x0 0x88200000 0x0 0x1500000>; + no-map; + }; + + pil_cdsp_mem: memory@89700000 { + reg = <0x0 0x89700000 0x0 0x1e00000>; + no-map; + }; + + pil_ipa_fw_mem: memory@8b500000 { + reg = <0x0 0x8b500000 0x0 0x10000>; + no-map; + }; + + pil_ipa_gsi_mem: memory@8b510000 { + reg = <0x0 0x8b510000 0x0 0xa000>; + no-map; + }; + + pil_gpu_mem: memory@8b51a000 { + reg = <0x0 0x8b51a000 0x0 0x2000>; + no-map; + }; + + pil_spss_mem: memory@8b600000 { + reg = <0x0 0x8b600000 0x0 0x100000>; + no-map; + }; + + pil_modem_mem: memory@8b800000 { + reg = <0x0 0x8b800000 0x0 0x10000000>; + no-map; + }; + + hyp_reserved_mem: memory@d0000000 { + reg = <0x0 0xd0000000 0x0 0x800000>; + no-map; + }; + + pil_trustedvm_mem: memory@d0800000 { + reg = <0x0 0xd0800000 0x0 0x76f7000>; + no-map; + }; + + qrtr_shbuf: memory@d7ef7000 { + reg = <0x0 0xd7ef7000 0x0 0x9000>; + no-map; + }; + + chan0_shbuf: memory@d7f00000 { + reg = <0x0 0xd7f00000 0x0 0x80000>; + no-map; + }; + + chan1_shbuf: memory@d7f80000 { + reg = <0x0 0xd7f80000 0x0 0x80000>; + no-map; + }; + + removed_mem: memory@d8800000 { + reg = <0x0 0xd8800000 0x0 0x6800000>; + no-map; + }; + }; + + smem: qcom,smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8350"; + reg = <0x0 0x00100000 0x0 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; + }; + + ipcc: mailbox@408000 { + compatible = "qcom,sm8350-ipcc", "qcom,ipcc"; + reg = <0 0x00408000 0 0x1000>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; + #mbox-cells = <2>; + }; + + qupv3_id_1: geniqup@9c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x009c0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 121>, + <&gcc 122>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart2: serial@98c000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc 83>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart3_default_state>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x0 0x01f40000 0x0 0x40000>; + #hwlock-cells = <1>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sm8350-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>, + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>, + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>, + <156 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sm8350-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + + tlmm: pinctrl@f100000 { + compatible = "qcom,sm8350-tlmm"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 203>; + + qup_uart3_default_state: qup-uart3-default-state { + rx { + pins = "gpio18"; + function = "qup3"; + }; + tx { + pins = "gpio19"; + function = "qup3"; + }; + }; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + compatible = "arm,armv7-timer-mem"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + reg = <0x0 0x17c20000 0x0 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c21000 0x0 0x1000>, + <0x0 0x17c22000 0x0 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c23000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c25000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c27000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c29000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2b000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2d000 0x0 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@18200000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x0 0x18200000 0x0 0x10000>, + <0x0 0x18210000 0x0 0x10000>, + <0x0 0x18220000 0x0 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>, + <WAKE_TCS 3>, <CONTROL_TCS 1>; + + rpmhcc: clock-controller { + compatible = "qcom,sm8350-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; + }; +}; diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile index 3b8b03705917..f2de2fa0c8b8 100644 --- a/arch/arm64/boot/dts/renesas/Makefile +++ b/arch/arm64/boot/dts/renesas/Makefile @@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-rev2.dtb dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-rev2-ex.dtb dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-rev2-ex-idk-1110wr.dtb +dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-beacon-rzg2n-kit.dtb dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-hihope-rzg2n.dtb dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-hihope-rzg2n-ex.dtb dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-hihope-rzg2n-ex-idk-1110wr.dtb @@ -21,6 +22,7 @@ dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-ek874.dtb dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-ek874-idk-2121wr.dtb dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-ek874-mipi-2.1.dtb +dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-beacon-rzg2h-kit.dtb dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-hihope-rzg2h.dtb dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-hihope-rzg2h-ex.dtb dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-hihope-rzg2h-ex-idk-1110wr.dtb diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index e66b5b36e489..30c169b08536 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -5,23 +5,24 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> +#include <dt-bindings/clk/versaclock.h> / { backlight_lvds: backlight-lvds { compatible = "pwm-backlight"; power-supply = <®_lcd>; - enable-gpios = <&gpio_exp1 3 GPIO_ACTIVE_LOW>; - pwms = <&pwm2 0 50000>; + enable-gpios = <&gpio_exp1 3 GPIO_ACTIVE_HIGH>; + pwms = <&pwm2 0 25000>; brightness-levels = <0 4 8 16 32 64 128 255>; default-brightness-level = <6>; }; - backlight_rgb: backlight-rgb { + backlight_dpi: backlight-dpi { compatible = "pwm-backlight"; power-supply = <®_lcd>; enable-gpios = <&gpio_exp1 7 GPIO_ACTIVE_LOW>; - pwms = <&pwm0 0 50000>; - brightness-levels = <0 4 8 16 32 64 128 255>; + pwms = <&pwm0 0 25000>; + brightness-levels = <0 25 33 50 63 75 88 100>; default-brightness-level = <6>; }; @@ -39,38 +40,38 @@ keys { compatible = "gpio-keys"; - key-1 { + key-1 { /* S19 */ gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; - linux,code = <KEY_1>; - label = "Switch-1"; + linux,code = <KEY_UP>; + label = "Up"; wakeup-source; debounce-interval = <20>; }; - key-2 { + key-2 { /*S20 */ gpios = <&gpio3 13 GPIO_ACTIVE_LOW>; - linux,code = <KEY_2>; - label = "Switch-2"; + linux,code = <KEY_LEFT>; + label = "Left"; wakeup-source; debounce-interval = <20>; }; - key-3 { + key-3 { /* S21 */ gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; - linux,code = <KEY_3>; - label = "Switch-3"; + linux,code = <KEY_DOWN>; + label = "Down"; wakeup-source; debounce-interval = <20>; }; - key-4 { + key-4 { /* S22 */ gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; - linux,code = <KEY_4>; - label = "Switch-4"; + linux,code = <KEY_RIGHT>; + label = "Right"; wakeup-source; debounce-interval = <20>; }; - key-5 { + key-5 { /* S23 */ gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; - linux,code = <KEY_5>; - label = "Switch-4"; + linux,code = <KEY_ENTER>; + label = "Center"; wakeup-source; debounce-interval = <20>; }; @@ -118,9 +119,9 @@ hback-porch = <40>; vfront-porch = <13>; vback-porch = <29>; - vsync-len = <3>; + vsync-len = <1>; hsync-active = <1>; - vsync-active = <1>; + vsync-active = <3>; de-active = <1>; pixelclk-active = <0>; }; @@ -135,7 +136,7 @@ rgb { /* Different LCD with compatible timings */ compatible = "rocktech,rk070er9427"; - backlight = <&backlight_rgb>; + backlight = <&backlight_dpi>; enable-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; power-supply = <®_lcd>; port { @@ -150,7 +151,7 @@ regulator-name = "audio-1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio_exp2 7 GPIO_ACTIVE_HIGH>; + gpio = <&gpio_exp4 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -200,15 +201,12 @@ vccq_sdhi0: regulator-vccq-sdhi0 { compatible = "regulator-gpio"; - regulator-name = "SDHI0 VccQ"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; - gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; gpios-states = <1>; states = <3300000 1>, <1800000 0>; - regulator-always-on; }; /* External DU dot clocks */ @@ -248,12 +246,6 @@ }; }; -&audio_clk_a { - clock-frequency = <24576000>; - assigned-clocks = <&versaclock6_bb 4>; - assigned-clock-rates = <24576000>; -}; - &audio_clk_b { clock-frequency = <22579200>; }; @@ -272,21 +264,6 @@ status = "okay"; }; -&du { - pinctrl-0 = <&du_pins>; - pinctrl-names = "default"; - status = "okay"; - - clocks = <&cpg CPG_MOD 724>, - <&cpg CPG_MOD 723>, - <&cpg CPG_MOD 722>, - <&versaclock5 1>, - <&x302_clk>, - <&versaclock5 2>; - clock-names = "du.0", "du.1", "du.2", - "dclkin.0", "dclkin.1", "dclkin.2"; -}; - &du_out_rgb { remote-endpoint = <&rgb_panel>; }; @@ -342,7 +319,7 @@ &i2c2 { status = "okay"; - clock-frequency = <100000>; + clock-frequency = <400000>; pinctrl-0 = <&i2c2_pins>; pinctrl-names = "default"; @@ -373,12 +350,36 @@ #clock-cells = <1>; clocks = <&x304_clk>; clock-names = "xin"; - /* CSI0_MCLK, CSI1_MCLK, AUDIO_CLKIN, USB_HUB_MCLK_BB */ + assigned-clocks = <&versaclock6_bb 1>, <&versaclock6_bb 2>, <&versaclock6_bb 3>, <&versaclock6_bb 4>; assigned-clock-rates = <24000000>, <24000000>, <24000000>, <24576000>; + + OUT1 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT2 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT3 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <3300000>; + idt,slew-percent = <100>; + }; + + OUT4 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <3300000>; + idt,slew-percent = <100>; + }; }; }; @@ -392,13 +393,14 @@ &i2c5 { status = "okay"; - clock-frequency = <100000>; + clock-frequency = <400000>; pinctrl-0 = <&i2c5_pins>; pinctrl-names = "default"; codec: wm8962@1a { compatible = "wlf,wm8962"; reg = <0x1a>; + clocks = <&versaclock6_bb 3>; DCVDD-supply = <®_audio>; DBVDD-supply = <®_audio>; AVDD-supply = <®_audio>; @@ -481,6 +483,13 @@ }; }; +&msiof1 { + pinctrl-0 = <&msiof1_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&gpio3 10 GPIO_ACTIVE_LOW>; +}; + &ohci0 { dr_mode = "otg"; status = "okay"; @@ -534,6 +543,11 @@ bias-pull-down; }; + msiof1_pins: msiof1 { + groups = "msiof1_clk_g", "msiof1_rxd_g", "msiof1_txd_g"; + function = "msiof1"; + }; + pwm0_pins: pwm0 { groups = "pwm0"; function = "pwm0"; @@ -541,7 +555,7 @@ pwm2_pins: pwm2 { groups = "pwm2_a"; - function = "pwm2_a"; + function = "pwm2"; }; sdhi0_pins: sd0 { @@ -562,7 +576,7 @@ }; sound_clk_pins: sound_clk { - groups = "audio_clk_a_a"; + groups = "audio_clk_a_a", "audio_clk_b_a"; function = "audio_clk"; }; @@ -613,23 +627,6 @@ status = "okay"; - clocks = <&cpg CPG_MOD 1005>, - <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, - <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, - <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, - <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, - <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, - <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, - <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, - <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, - <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, - <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, - <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, - <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, - <&cpg CPG_CORE R8A774A1_CLK_S0D4>; - ports { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index 8ac167aa18f0..8d3a4d6ee885 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -4,6 +4,7 @@ */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clk/versaclock.h> / { memory@48000000 { @@ -12,11 +13,6 @@ reg = <0x0 0x48000000 0x0 0x78000000>; }; - memory@600000000 { - device_type = "memory"; - reg = <0x6 0x00000000 0x0 0x80000000>; - }; - osc_32k: osc_32k { compatible = "fixed-clock"; #clock-cells = <0>; @@ -89,7 +85,6 @@ pinctrl-names = "default"; uart-has-rtscts; status = "okay"; - max-speed = <4000000>; bluetooth { compatible = "brcm,bcm43438-bt"; @@ -98,6 +93,7 @@ device-wakeup-gpios = <&pca9654 5 GPIO_ACTIVE_HIGH>; clocks = <&osc_32k>; clock-names = "extclk"; + max-speed = <4000000>; }; }; @@ -109,7 +105,7 @@ &i2c4 { status = "okay"; - clock-frequency = <400000>; + clock-frequency = <100000>; pca9654: gpio@20 { compatible = "onnn,pca9654"; @@ -148,7 +144,7 @@ }; eeprom@50 { - compatible = "microchip,at24c64", "atmel,24c64"; + compatible = "microchip,24c64", "atmel,24c64"; pagesize = <32>; read-only; /* Manufacturing EEPROM programmed at factory */ reg = <0x50>; @@ -170,7 +166,32 @@ <&versaclock5 2>, <&versaclock5 3>, <&versaclock5 4>; + assigned-clock-rates = <33333333>, <33333333>, <50000000>, <125000000>; + + OUT1 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT2 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT3 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT4 { + idt,mode = <VC5_CMOS>; + idt,voltage-microvolt = <3300000>; + idt,slew-percent = <100>; + }; }; }; @@ -291,6 +312,8 @@ vqmmc-supply = <®_1p8v>; bus-width = <8>; mmc-hs200-1_8v; + no-sd; + no-sdio; non-removable; fixed-emmc-driver-type = <1>; status = "okay"; @@ -303,11 +326,3 @@ &usb3s0_clk { clock-frequency = <100000000>; }; - -&vspb { - status = "okay"; -}; - -&vspi0 { - status = "okay"; -}; diff --git a/arch/arm64/boot/dts/renesas/hihope-common.dtsi b/arch/arm64/boot/dts/renesas/hihope-common.dtsi index 2eda9f66ae81..7a3da9b06f67 100644 --- a/arch/arm64/boot/dts/renesas/hihope-common.dtsi +++ b/arch/arm64/boot/dts/renesas/hihope-common.dtsi @@ -328,6 +328,8 @@ vqmmc-supply = <®_1p8v>; bus-width = <8>; mmc-hs200-1_8v; + no-sd; + no-sdio; non-removable; fixed-emmc-driver-type = <1>; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts index 2c5b057c30c6..501cb05da228 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts +++ b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts @@ -26,4 +26,45 @@ chosen { stdout-path = "serial0:115200n8"; }; + + memory@600000000 { + device_type = "memory"; + reg = <0x6 0x00000000 0x0 0x80000000>; + }; +}; + +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 722>, + <&versaclock5 1>, + <&x302_clk>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.2", + "dclkin.0", "dclkin.1", "dclkin.2"; +}; + +/* Reference versaclock instead of audio_clk_a */ +&rcar_sound { + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&versaclock6_bb 4>, <&audio_clk_b>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A774A1_CLK_S0D4>; }; diff --git a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi index d37ec42a1caa..d64fb8b1b86c 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi @@ -835,6 +835,21 @@ status = "disabled"; }; + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a774a1-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal_clk>, <&usb3s0_clk>; + clock-names = "ehci_ohci", "hs-usb-if", + "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + status = "disabled"; + }; + usb_dmac0: dma-controller@e65a0000 { compatible = "renesas,r8a774a1-usb-dmac", "renesas,usb-dmac"; @@ -2302,6 +2317,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774a1-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@f1010000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; diff --git a/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts new file mode 100644 index 000000000000..71763f4402a7 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts @@ -0,0 +1,66 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2020, Compass Electronics Group, LLC + */ + +/dts-v1/; + +#include "r8a774b1.dtsi" +#include "beacon-renesom-som.dtsi" +#include "beacon-renesom-baseboard.dtsi" + +/ { + model = "Beacon Embedded Works RZ/G2N Development Kit"; + compatible = "beacon,beacon-rzg2n", "renesas,r8a774b1"; + + aliases { + serial0 = &scif2; + serial1 = &hscif0; + serial2 = &hscif1; + serial3 = &scif0; + serial4 = &hscif2; + serial5 = &scif5; + serial6 = &scif4; + ethernet0 = &avb; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 721>, + <&versaclock5 1>, + <&x302_clk>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.3", + "dclkin.0", "dclkin.1", "dclkin.3"; +}; + +/* Reference versaclock instead of audio_clk_a */ +&rcar_sound { + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&versaclock6_bb 4>, <&audio_clk_b>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A774B1_CLK_S0D4>; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi index 83523916d360..5b05474dc272 100644 --- a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi @@ -709,6 +709,21 @@ status = "disabled"; }; + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a774b1-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal_clk>, <&usb3s0_clk>; + clock-names = "ehci_ohci", "hs-usb-if", + "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + status = "disabled"; + }; + usb_dmac0: dma-controller@e65a0000 { compatible = "renesas,r8a774b1-usb-dmac", "renesas,usb-dmac"; @@ -2160,6 +2175,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774b1-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sata: sata@ee300000 { compatible = "renesas,sata-r8a774b1", "renesas,rcar-gen3-sata"; diff --git a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi index e0e54342cd4c..20fa3caa050e 100644 --- a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi @@ -1654,6 +1654,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774c0-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@f1010000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; diff --git a/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts new file mode 100644 index 000000000000..273f062f2909 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts @@ -0,0 +1,71 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2020, Compass Electronics Group, LLC + */ + +/dts-v1/; + +#include "r8a774e1.dtsi" +#include "beacon-renesom-som.dtsi" +#include "beacon-renesom-baseboard.dtsi" + +/ { + model = "Beacon Embedded Works RZ/G2H Development Kit"; + compatible = "beacon,beacon-rzg2h", "renesas,r8a774e1"; + + aliases { + serial0 = &scif2; + serial1 = &hscif0; + serial2 = &hscif1; + serial3 = &scif0; + serial4 = &hscif2; + serial5 = &scif5; + serial6 = &scif4; + ethernet0 = &avb; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@500000000 { + device_type = "memory"; + reg = <0x5 0x00000000 0x0 0x80000000>; + }; +}; + +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 721>, + <&versaclock5 1>, + <&x302_clk>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.3", + "dclkin.0", "dclkin.1", "dclkin.3"; +}; + +/* Reference versaclock instead of audio_clk_a */ +&rcar_sound { + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&versaclock6_bb 4>, <&audio_clk_b>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A774E1_CLK_S0D4>; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi index 1333b02d623a..8eb006cbd9af 100644 --- a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi @@ -890,6 +890,21 @@ status = "disabled"; }; + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a774e1-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal_clk>, <&usb3s0_clk>; + clock-names = "ehci_ohci", "hs-usb-if", + "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + status = "disabled"; + }; + usb_dmac0: dma-controller@e65a0000 { compatible = "renesas,r8a774e1-usb-dmac", "renesas,usb-dmac"; @@ -2393,6 +2408,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774e1-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sata: sata@ee300000 { compatible = "renesas,sata-r8a774e1", "renesas,rcar-gen3-sata"; diff --git a/arch/arm64/boot/dts/renesas/r8a77951.dtsi b/arch/arm64/boot/dts/renesas/r8a77951.dtsi index 9d60bcf69e4f..5c39152e4570 100644 --- a/arch/arm64/boot/dts/renesas/r8a77951.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77951.dtsi @@ -616,6 +616,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77960.dtsi b/arch/arm64/boot/dts/renesas/r8a77960.dtsi index 53b9aa26c9b1..25d947a81b29 100644 --- a/arch/arm64/boot/dts/renesas/r8a77960.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77960.dtsi @@ -585,6 +585,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi index 4b737c616257..e8c31ebec097 100644 --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi @@ -453,6 +453,76 @@ reg = <0 0xe6060000 0 0x50c>; }; + cmt0: timer@e60f0000 { + compatible = "renesas,r8a77961-cmt0", + "renesas,rcar-gen3-cmt0"; + reg = <0 0xe60f0000 0 0x1004>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 303>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 303>; + status = "disabled"; + }; + + cmt1: timer@e6130000 { + compatible = "renesas,r8a77961-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6130000 0 0x1004>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 302>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 302>; + status = "disabled"; + }; + + cmt2: timer@e6140000 { + compatible = "renesas,r8a77961-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6140000 0 0x1004>; + interrupts = <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 301>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 301>; + status = "disabled"; + }; + + cmt3: timer@e6148000 { + compatible = "renesas,r8a77961-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6148000 0 0x1004>; + interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 300>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 300>; + status = "disabled"; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a77961-cpg-mssr"; reg = <0 0xe6150000 0 0x1000>; @@ -495,6 +565,71 @@ /* placeholder */ }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi index 4a913df17b1d..657b20d3533b 100644 --- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi @@ -455,6 +455,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts index 422ec53740cb..04d47c0c9bb9 100644 --- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts +++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts @@ -217,6 +217,8 @@ vqmmc-supply = <&vddq_vin01>; mmc-hs200-1_8v; bus-width = <8>; + no-sd; + no-sdio; non-removable; status = "okay"; }; diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts index e0ccca2222d2..f74f8b9993f1 100644 --- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts +++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts @@ -712,6 +712,8 @@ mmc-hs200-1_8v; mmc-hs400-1_8v; bus-width = <8>; + no-sd; + no-sdio; non-removable; full-pwr-cycle-in-suspend; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/r8a77990.dtsi b/arch/arm64/boot/dts/renesas/r8a77990.dtsi index 87d41bc076a9..5010f23fafcc 100644 --- a/arch/arm64/boot/dts/renesas/r8a77990.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77990.dtsi @@ -420,6 +420,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts index 8f471881b7a3..6783c3ad0856 100644 --- a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts +++ b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts @@ -496,6 +496,8 @@ vqmmc-supply = <®_1p8v>; bus-width = <8>; mmc-hs200-1_8v; + no-sd; + no-sdio; non-removable; status = "okay"; }; diff --git a/arch/arm64/boot/dts/renesas/r8a77995.dtsi b/arch/arm64/boot/dts/renesas/r8a77995.dtsi index e1af7c4782f4..2319271c881b 100644 --- a/arch/arm64/boot/dts/renesas/r8a77995.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77995.dtsi @@ -193,6 +193,76 @@ reg = <0 0xe6060000 0 0x508>; }; + cmt0: timer@e60f0000 { + compatible = "renesas,r8a77995-cmt0", + "renesas,rcar-gen3-cmt0"; + reg = <0 0xe60f0000 0 0x1004>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 303>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 303>; + status = "disabled"; + }; + + cmt1: timer@e6130000 { + compatible = "renesas,r8a77995-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6130000 0 0x1004>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 302>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 302>; + status = "disabled"; + }; + + cmt2: timer@e6140000 { + compatible = "renesas,r8a77995-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6140000 0 0x1004>; + interrupts = <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 301>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 301>; + status = "disabled"; + }; + + cmt3: timer@e6148000 { + compatible = "renesas,r8a77995-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6148000 0 0x1004>; + interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 300>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 300>; + status = "disabled"; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a77995-cpg-mssr"; reg = <0 0xe6150000 0 0x1000>; @@ -242,6 +312,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi index 4ba269a4cec8..fa284a7260d6 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi @@ -5,6 +5,7 @@ * Copyright (C) 2020 Renesas Electronics Corp. */ +#include <dt-bindings/gpio/gpio.h> #include "r8a779a0.dtsi" / { @@ -31,6 +32,40 @@ device_type = "memory"; reg = <0x7 0x00000000 0x0 0x80000000>; }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&avb0 { + pinctrl-0 = <&avb0_pins>; + pinctrl-names = "default"; + phy-handle = <&phy0>; + tx-internal-delay-ps = <2000>; + status = "okay"; + + phy0: ethernet-phy@0 { + rxc-skew-ps = <1500>; + reg = <0>; + interrupt-parent = <&gpio4>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + }; }; &extal_clk { @@ -41,6 +76,109 @@ clock-frequency = <32768>; }; +&i2c0 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + +&i2c1 { + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + +&i2c6 { + pinctrl-0 = <&i2c6_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + +&mmc0 { + pinctrl-0 = <&mmc_pins>; + pinctrl-1 = <&mmc_pins>; + pinctrl-names = "default", "state_uhs"; + + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + full-pwr-cycle-in-suspend; + status = "okay"; +}; + +&pfc { + pinctrl-0 = <&scif_clk_pins>; + pinctrl-names = "default"; + + avb0_pins: avb0 { + mux { + groups = "avb0_link", "avb0_mdio", "avb0_rgmii", "avb0_txcrefclk"; + function = "avb0"; + }; + + pins_mdio { + groups = "avb0_mdio"; + drive-strength = <21>; + }; + + pins_mii { + groups = "avb0_rgmii"; + drive-strength = <21>; + }; + + }; + + i2c0_pins: i2c0 { + groups = "i2c0"; + function = "i2c0"; + }; + + i2c1_pins: i2c1 { + groups = "i2c1"; + function = "i2c1"; + }; + + i2c6_pins: i2c6 { + groups = "i2c6"; + function = "i2c6"; + }; + + mmc_pins: mmc { + groups = "mmc_data8", "mmc_ctrl", "mmc_ds"; + function = "mmc"; + power-source = <1800>; + }; + + scif0_pins: scif0 { + groups = "scif0_data", "scif0_ctrl"; + function = "scif0"; + }; + + scif_clk_pins: scif_clk { + groups = "scif_clk"; + function = "scif_clk"; + }; +}; + &scif0 { + pinctrl-0 = <&scif0_pins>; + pinctrl-names = "default"; + + uart-has-rtscts; status = "okay"; }; + +&scif_clk { + clock-frequency = <24000000>; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts index 8eda70e5a82b..5617b81dd7dc 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts @@ -13,6 +13,7 @@ compatible = "renesas,falcon-breakout", "renesas,falcon-cpu", "renesas,r8a779a0"; aliases { + ethernet0 = &avb0; serial0 = &scif0; }; @@ -20,3 +21,8 @@ stdout-path = "serial0:115200n8"; }; }; + +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 6cf77ce9aa93..dfd6ae8b564f 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -14,6 +14,16 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -70,6 +80,165 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a779a0-wdt", + "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 907>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 907>; + status = "disabled"; + }; + + pfc: pin-controller@e6050000 { + compatible = "renesas,pfc-r8a779a0"; + reg = <0 0xe6050000 0 0x16c>, <0 0xe6050800 0 0x16c>, + <0 0xe6058000 0 0x16c>, <0 0xe6058800 0 0x16c>, + <0 0xe6060000 0 0x16c>, <0 0xe6060800 0 0x16c>, + <0 0xe6068000 0 0x16c>, <0 0xe6068800 0 0x16c>, + <0 0xe6069000 0 0x16c>, <0 0xe6069800 0 0x16c>; + }; + + gpio0: gpio@e6058180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6058180 0 0x54>; + interrupts = <GIC_SPI 832 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 916>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 916>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 0 28>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@e6050180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6050180 0 0x54>; + interrupts = <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 915>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 915>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 32 31>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@e6050980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6050980 0 0x54>; + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 915>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 915>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 64 25>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@e6058980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6058980 0 0x54>; + interrupts = <GIC_SPI 844 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 916>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 916>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 96 17>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@e6060180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6060180 0 0x54>; + interrupts = <GIC_SPI 848 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 917>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 128 27>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio5: gpio@e6060980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6060980 0 0x54>; + interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 917>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 160 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio6: gpio@e6068180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6068180 0 0x54>; + interrupts = <GIC_SPI 856 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 192 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio7: gpio@e6068980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6068980 0 0x54>; + interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 224 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio8: gpio@e6069180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6069180 0 0x54>; + interrupts = <GIC_SPI 864 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 256 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio9: gpio@e6069980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6069980 0 0x54>; + interrupts = <GIC_SPI 868 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 288 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a779a0-cpg-mssr"; reg = <0 0xe6150000 0 0x4000>; @@ -91,6 +260,464 @@ #power-domain-cells = <1>; }; + i2c0: i2c@e6500000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe6500000 0 0x40>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 518>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 518>; + dmas = <&dmac1 0x91>, <&dmac1 0x90>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@e6508000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 519>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 519>; + dmas = <&dmac1 0x93>, <&dmac1 0x92>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@e6510000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe6510000 0 0x40>; + interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 520>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 520>; + dmas = <&dmac1 0x95>, <&dmac1 0x94>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@e66d0000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66d0000 0 0x40>; + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 521>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 521>; + dmas = <&dmac1 0x97>, <&dmac1 0x96>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@e66d8000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66d8000 0 0x40>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 522>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 522>; + dmas = <&dmac1 0x99>, <&dmac1 0x98>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@e66e0000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66e0000 0 0x40>; + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 523>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 523>; + dmas = <&dmac1 0x9b>, <&dmac1 0x9a>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@e66e8000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66e8000 0 0x40>; + interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 524>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 524>; + dmas = <&dmac1 0x9d>, <&dmac1 0x9c>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + hscif0: serial@e6540000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe6540000 0 0x60>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x31>, <&dmac1 0x30>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 514>; + status = "disabled"; + }; + + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe6550000 0 0x60>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x33>, <&dmac1 0x32>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 515>; + status = "disabled"; + }; + + hscif2: serial@e6560000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe6560000 0 0x60>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 516>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x35>, <&dmac1 0x34>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 516>; + status = "disabled"; + }; + + hscif3: serial@e66a0000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe66a0000 0 0x60>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 517>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x37>, <&dmac1 0x36>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 517>; + status = "disabled"; + }; + + avb0: ethernet@e6800000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6800000 0 0x800>; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 211>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 211>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb1: ethernet@e6810000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6810000 0 0x800>; + interrupts = <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 289 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 291 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 212>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 212>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb2: ethernet@e6820000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6820000 0 0x1000>; + interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 213>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 213>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb3: ethernet@e6830000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6830000 0 0x1000>; + interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 214>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 214>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb4: ethernet@e6840000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6840000 0 0x1000>; + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 380 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 215>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 215>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb5: ethernet@e6850000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6850000 0 0x1000>; + interrupts = <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 216>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 216>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + scif0: serial@e6e60000 { compatible = "renesas,scif-r8a779a0", "renesas,rcar-gen3-scif", "renesas,scif"; @@ -100,11 +727,221 @@ <&cpg CPG_CORE R8A779A0_CLK_S1D2>, <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x51>, <&dmac1 0x50>; + dma-names = "tx", "rx"; power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; resets = <&cpg 702>; status = "disabled"; }; + scif1: serial@e6e68000 { + compatible = "renesas,scif-r8a779a0", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6e68000 0 64>; + interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 703>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x53>, <&dmac1 0x52>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 703>; + status = "disabled"; + }; + + scif3: serial@e6c50000 { + compatible = "renesas,scif-r8a779a0", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6c50000 0 64>; + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 704>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x57>, <&dmac1 0x56>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 704>; + status = "disabled"; + }; + + scif4: serial@e6c40000 { + compatible = "renesas,scif-r8a779a0", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6c40000 0 64>; + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 705>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x59>, <&dmac1 0x58>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 705>; + status = "disabled"; + }; + + msiof0: spi@e6e90000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6e90000 0 0x0064>; + interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 618>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 618>; + dmas = <&dmac1 0x41>, <&dmac1 0x40>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof1: spi@e6ea0000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6ea0000 0 0x0064>; + interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 619>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 619>; + dmas = <&dmac1 0x43>, <&dmac1 0x42>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof2: spi@e6c00000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c00000 0 0x0064>; + interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 620>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 620>; + dmas = <&dmac1 0x45>, <&dmac1 0x44>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof3: spi@e6c10000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c10000 0 0x0064>; + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 621>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 621>; + dmas = <&dmac1 0x47>, <&dmac1 0x46>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof4: spi@e6c20000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c20000 0 0x0064>; + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 622>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 622>; + dmas = <&dmac1 0x49>, <&dmac1 0x48>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof5: spi@e6c28000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c28000 0 0x0064>; + interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 623>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 623>; + dmas = <&dmac1 0x4b>, <&dmac1 0x4a>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + dmac1: dma-controller@e7350000 { + compatible = "renesas,dmac-r8a779a0"; + reg = <0 0xe7350000 0 0x1000>, + <0 0xe7300000 0 0x10000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", "ch4", + "ch5", "ch6", "ch7", "ch8", "ch9", + "ch10", "ch11", "ch12", "ch13", + "ch14", "ch15"; + clocks = <&cpg CPG_MOD 709>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 709>; + #dma-cells = <1>; + dma-channels = <16>; + }; + + dmac2: dma-controller@e7351000 { + compatible = "renesas,dmac-r8a779a0"; + reg = <0 0xe7351000 0 0x1000>, + <0 0xe7310000 0 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", "ch4", + "ch5", "ch6", "ch7"; + clocks = <&cpg CPG_MOD 710>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 710>; + #dma-cells = <1>; + dma-channels = <8>; + }; + + mmc0: mmc@ee140000 { + compatible = "renesas,sdhi-r8a779a0", + "renesas,rcar-gen3-sdhi"; + reg = <0 0xee140000 0 0x2000>; + interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 706>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 706>; + max-frequency = <200000000>; + status = "disabled"; + }; + gic: interrupt-controller@f1000000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi index 6c643ed74fc5..c22bb38994e8 100644 --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi @@ -831,6 +831,8 @@ bus-width = <8>; mmc-hs200-1_8v; mmc-hs400-1_8v; + no-sd; + no-sdio; non-removable; fixed-emmc-driver-type = <1>; full-pwr-cycle-in-suspend; diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi index 8f8d7371d8e2..a04eae55dd6c 100644 --- a/arch/arm64/boot/dts/renesas/ulcb.dtsi +++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi @@ -468,6 +468,8 @@ bus-width = <8>; mmc-hs200-1_8v; mmc-hs400-1_8v; + no-sd; + no-sdio; non-removable; full-pwr-cycle-in-suspend; status = "okay"; diff --git a/arch/arm64/boot/dts/synaptics/as370.dtsi b/arch/arm64/boot/dts/synaptics/as370.dtsi index addeb0efc616..4bb5d650df9c 100644 --- a/arch/arm64/boot/dts/synaptics/as370.dtsi +++ b/arch/arm64/boot/dts/synaptics/as370.dtsi @@ -143,7 +143,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -161,7 +161,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi b/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi index 15625b99e336..0949acee4728 100644 --- a/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi +++ b/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi @@ -140,7 +140,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -158,7 +158,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -176,7 +176,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -194,7 +194,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -269,7 +269,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; }; }; @@ -284,7 +284,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; }; }; diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi index 12591a854020..ceb579fb427d 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi @@ -256,7 +256,7 @@ #size-cells = <0>; }; - sdhci0: sdhci@4f80000 { + sdhci0: mmc@4f80000 { compatible = "ti,am654-sdhci-5.1"; reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>; power-domains = <&k3_pds 47 TI_SCI_PD_EXCLUSIVE>; @@ -280,7 +280,7 @@ dma-coherent; }; - sdhci1: sdhci@4fa0000 { + sdhci1: mmc@4fa0000 { compatible = "ti,am654-sdhci-5.1"; reg = <0x0 0x4fa0000 0x0 0x260>, <0x0 0x4fb0000 0x0 0x134>; power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>; diff --git a/arch/arm64/boot/dts/ti/k3-am65.dtsi b/arch/arm64/boot/dts/ti/k3-am65.dtsi index d84c0bc05023..a9fc1af03f27 100644 --- a/arch/arm64/boot/dts/ti/k3-am65.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65.dtsi @@ -56,7 +56,7 @@ }; pmu: pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a53-pmu"; /* Recommendation from GIC500 TRM Table A.3 */ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index 331b388e1d1b..4a7182abccf5 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -6,8 +6,10 @@ /dts-v1/; #include "k3-j7200-som-p0.dtsi" +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/net/ti-dp83867.h> #include <dt-bindings/mux/ti-serdes.h> +#include <dt-bindings/phy/phy.h> / { chosen { @@ -218,3 +220,39 @@ ti,adc-channels = <0 1 2 3 4 5 6 7>; }; }; + +&serdes_refclk { + clock-frequency = <100000000>; +}; + +&serdes0 { + serdes0_pcie_link: phy@0 { + reg = <0>; + cdns,num-lanes = <2>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>; + }; + + serdes0_qsgmii_link: phy@1 { + reg = <2>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_QSGMII>; + resets = <&serdes_wiz0 3>; + }; +}; + +&pcie1_rc { + reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <2>; +}; + +&pcie1_ep { + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <2>; + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index b0094212aa82..17477ab0fd8e 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -2,9 +2,16 @@ /* * Device Tree Source for J7200 SoC Family Main Domain peripherals * - * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ +/ { + serdes_refclk: serdes-refclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; +}; + &cbass_main { msmc_ram: sram@70000000 { compatible = "mmio-sram"; @@ -499,8 +506,8 @@ reg = <0x00 0x04f80000 0x00 0x260>, <0x00 0x4f88000 0x00 0x134>; interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; power-domains = <&k3_pds 91 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 91 3>, <&k3_clks 91 0>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 91 0>, <&k3_clks 91 3>; ti,otap-del-sel-legacy = <0x0>; ti,otap-del-sel-mmc-hs = <0x0>; ti,otap-del-sel-ddr52 = <0x6>; @@ -518,8 +525,8 @@ reg = <0x00 0x04fb0000 0x00 0x260>, <0x00 0x4fb8000 0x00 0x134>; interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; power-domains = <&k3_pds 92 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 92 2>, <&k3_clks 92 1>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 92 1>, <&k3_clks 92 2>; ti,otap-del-sel-legacy = <0x0>; ti,otap-del-sel-sd-hs = <0x0>; ti,otap-del-sel-sdr12 = <0xf>; @@ -531,6 +538,110 @@ dma-coherent; }; + serdes_wiz0: wiz@5060000 { + compatible = "ti,j721e-wiz-10g"; + #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 292 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 292 11>, <&k3_clks 292 85>, <&serdes_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + num-lanes = <4>; + #reset-cells = <1>; + ranges = <0x5060000 0x0 0x5060000 0x10000>; + + assigned-clocks = <&k3_clks 292 85>; + assigned-clock-parents = <&k3_clks 292 89>; + + wiz0_pll0_refclk: pll0-refclk { + clocks = <&k3_clks 292 85>, <&serdes_refclk>; + clock-output-names = "wiz0_pll0_refclk"; + #clock-cells = <0>; + assigned-clocks = <&wiz0_pll0_refclk>; + assigned-clock-parents = <&k3_clks 292 85>; + }; + + wiz0_pll1_refclk: pll1-refclk { + clocks = <&k3_clks 292 85>, <&serdes_refclk>; + clock-output-names = "wiz0_pll1_refclk"; + #clock-cells = <0>; + assigned-clocks = <&wiz0_pll1_refclk>; + assigned-clock-parents = <&k3_clks 292 85>; + }; + + wiz0_refclk_dig: refclk-dig { + clocks = <&k3_clks 292 85>, <&serdes_refclk>; + clock-output-names = "wiz0_refclk_dig"; + #clock-cells = <0>; + assigned-clocks = <&wiz0_refclk_dig>; + assigned-clock-parents = <&k3_clks 292 85>; + }; + + wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div { + clocks = <&wiz0_refclk_dig>; + #clock-cells = <0>; + }; + + serdes0: serdes@5060000 { + compatible = "ti,j721e-serdes-10g"; + reg = <0x05060000 0x00010000>; + reg-names = "torrent_phy"; + resets = <&serdes_wiz0 0>; + reset-names = "torrent_reset"; + clocks = <&wiz0_pll0_refclk>; + clock-names = "refclk"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + pcie1_rc: pcie@2910000 { + compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host"; + reg = <0x00 0x02910000 0x00 0x1000>, + <0x00 0x02917000 0x00 0x400>, + <0x00 0x0d800000 0x00 0x00800000>, + <0x00 0x18000000 0x00 0x00001000>; + reg-names = "intd_cfg", "user_cfg", "reg", "cfg"; + interrupt-names = "link_state"; + interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>; + device_type = "pci"; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; + max-link-speed = <3>; + num-lanes = <4>; + power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 240 6>; + clock-names = "fck"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xf>; + cdns,no-bar-match-nbits = <64>; + vendor-id = /bits/ 16 <0x104c>; + device-id = /bits/ 16 <0xb00f>; + msi-map = <0x0 &gic_its 0x0 0x10000>; + dma-coherent; + ranges = <0x01000000 0x0 0x18001000 0x00 0x18001000 0x0 0x0010000>, + <0x02000000 0x0 0x18011000 0x00 0x18011000 0x0 0x7fef000>; + dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>; + }; + + pcie1_ep: pcie-ep@2910000 { + compatible = "ti,j7200-pcie-ep", "ti,j721e-pcie-ep"; + reg = <0x00 0x02910000 0x00 0x1000>, + <0x00 0x02917000 0x00 0x400>, + <0x00 0x0d800000 0x00 0x00800000>, + <0x00 0x18000000 0x00 0x08000000>; + reg-names = "intd_cfg", "user_cfg", "reg", "mem"; + interrupt-names = "link_state"; + interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; + max-link-speed = <3>; + num-lanes = <4>; + power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 240 6>; + clock-names = "fck"; + max-functions = /bits/ 8 <6>; + dma-coherent; + }; + usbss0: cdns-usb@4104000 { compatible = "ti,j721e-usb"; reg = <0x00 0x4104000 0x00 0x100>; @@ -560,4 +671,44 @@ dr_mode = "otg"; }; }; + + main_r5fss0: r5fss@5c00000 { + compatible = "ti,j7200-r5fss"; + ti,cluster-mode = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x5c00000 0x00 0x5c00000 0x20000>, + <0x5d00000 0x00 0x5d00000 0x20000>; + power-domains = <&k3_pds 243 TI_SCI_PD_EXCLUSIVE>; + + main_r5fss0_core0: r5f@5c00000 { + compatible = "ti,j7200-r5f"; + reg = <0x5c00000 0x00010000>, + <0x5c10000 0x00010000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <245>; + ti,sci-proc-ids = <0x06 0xff>; + resets = <&k3_reset 245 1>; + firmware-name = "j7200-main-r5f0_0-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + + main_r5fss0_core1: r5f@5d00000 { + compatible = "ti,j7200-r5f"; + reg = <0x5d00000 0x00008000>, + <0x5d10000 0x00008000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <246>; + ti,sci-proc-ids = <0x07 0xff>; + resets = <&k3_reset 246 1>; + firmware-name = "j7200-main-r5f0_1-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + }; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi index bb1fe9c12e44..359e3e8a8cd0 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi @@ -2,7 +2,7 @@ /* * Device Tree Source for J7200 SoC Family MCU/WAKEUP Domain peripherals * - * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ &cbass_mcu_wakeup { @@ -289,4 +289,44 @@ compatible = "ti,am3359-adc"; }; }; + + mcu_r5fss0: r5fss@41000000 { + compatible = "ti,j7200-r5fss"; + ti,cluster-mode = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x41000000 0x00 0x41000000 0x20000>, + <0x41400000 0x00 0x41400000 0x20000>; + power-domains = <&k3_pds 249 TI_SCI_PD_EXCLUSIVE>; + + mcu_r5fss0_core0: r5f@41000000 { + compatible = "ti,j7200-r5f"; + reg = <0x41000000 0x00010000>, + <0x41010000 0x00010000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <250>; + ti,sci-proc-ids = <0x01 0xff>; + resets = <&k3_reset 250 1>; + firmware-name = "j7200-mcu-r5f0_0-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + + mcu_r5fss0_core1: r5f@41400000 { + compatible = "ti,j7200-r5f"; + reg = <0x41400000 0x00008000>, + <0x41410000 0x00008000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <251>; + ti,sci-proc-ids = <0x02 0xff>; + resets = <&k3_reset 251 1>; + firmware-name = "j7200-mcu-r5f0_1-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + }; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi index 7b5e9aa0324e..a988e2ab2ba1 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 /* - * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ /dts-v1/; @@ -25,6 +25,60 @@ alignment = <0x1000>; no-map; }; + + mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0000000 0x00 0x100000>; + no-map; + }; + + mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0100000 0x00 0xf00000>; + no-map; + }; + + mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1000000 0x00 0x100000>; + no-map; + }; + + mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core0_memory_region: r5f-memory@a2100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core1_memory_region: r5f-memory@a3100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3100000 0x00 0xf00000>; + no-map; + }; + + rtos_ipc_memory_region: ipc-memories@a4000000 { + reg = <0x00 0xa4000000 0x00 0x00800000>; + alignment = <0x1000>; + no-map; + }; }; }; @@ -141,6 +195,30 @@ status = "disabled"; }; +&mcu_r5fss0_core0 { + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>; + memory-region = <&mcu_r5fss0_core0_dma_memory_region>, + <&mcu_r5fss0_core0_memory_region>; +}; + +&mcu_r5fss0_core1 { + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>; + memory-region = <&mcu_r5fss0_core1_dma_memory_region>, + <&mcu_r5fss0_core1_memory_region>; +}; + +&main_r5fss0_core0 { + mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>; + memory-region = <&main_r5fss0_core0_dma_memory_region>, + <&main_r5fss0_core0_memory_region>; +}; + +&main_r5fss0_core1 { + mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>; + memory-region = <&main_r5fss0_core1_dma_memory_region>, + <&main_r5fss0_core1_memory_region>; +}; + &main_i2c0 { pinctrl-names = "default"; pinctrl-0 = <&main_i2c0_pins_default>; diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi index 66169bcf7c9a..b7005b803149 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi @@ -114,7 +114,7 @@ }; pmu: pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a72-pmu"; interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi index b32df591c766..8c84dafb7125 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi @@ -28,38 +28,6 @@ #size-cells = <1>; ranges = <0x0 0x0 0x00100000 0x1c000>; - pcie0_ctrl: syscon@4070 { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x00004070 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x4070 0x4070 0x4>; - }; - - pcie1_ctrl: syscon@4074 { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x00004074 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x4074 0x4074 0x4>; - }; - - pcie2_ctrl: syscon@4078 { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x00004078 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x4078 0x4078 0x4>; - }; - - pcie3_ctrl: syscon@407c { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x0000407c 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x407c 0x407c 0x4>; - }; - serdes_ln_ctrl: mux@4080 { compatible = "mmio-mux"; reg = <0x00004080 0x50>; @@ -618,7 +586,7 @@ interrupt-names = "link_state"; interrupts = <GIC_SPI 318 IRQ_TYPE_EDGE_RISING>; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie0_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4070>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; @@ -645,13 +613,12 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = <GIC_SPI 318 IRQ_TYPE_EDGE_RISING>; - ti,syscon-pcie-ctrl = <&pcie0_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4070>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 239 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -667,7 +634,7 @@ interrupt-names = "link_state"; interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie1_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; @@ -694,13 +661,12 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>; - ti,syscon-pcie-ctrl = <&pcie1_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 240 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -716,7 +682,7 @@ interrupt-names = "link_state"; interrupts = <GIC_SPI 342 IRQ_TYPE_EDGE_RISING>; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie2_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4078>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 241 TI_SCI_PD_EXCLUSIVE>; @@ -743,13 +709,12 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = <GIC_SPI 342 IRQ_TYPE_EDGE_RISING>; - ti,syscon-pcie-ctrl = <&pcie2_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4078>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 241 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 241 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -765,7 +730,7 @@ interrupt-names = "link_state"; interrupts = <GIC_SPI 354 IRQ_TYPE_EDGE_RISING>; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie3_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x407c>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 242 TI_SCI_PD_EXCLUSIVE>; @@ -792,13 +757,12 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = <GIC_SPI 354 IRQ_TYPE_EDGE_RISING>; - ti,syscon-pcie-ctrl = <&pcie3_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x407c>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 242 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 242 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -1068,13 +1032,13 @@ clock-names = "gpio"; }; - main_sdhci0: sdhci@4f80000 { + main_sdhci0: mmc@4f80000 { compatible = "ti,j721e-sdhci-8bit"; reg = <0x0 0x4f80000 0x0 0x1000>, <0x0 0x4f88000 0x0 0x400>; interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; power-domains = <&k3_pds 91 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 91 1>, <&k3_clks 91 0>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 91 0>, <&k3_clks 91 1>; assigned-clocks = <&k3_clks 91 1>; assigned-clock-parents = <&k3_clks 91 2>; bus-width = <8>; @@ -1090,13 +1054,13 @@ dma-coherent; }; - main_sdhci1: sdhci@4fb0000 { + main_sdhci1: mmc@4fb0000 { compatible = "ti,j721e-sdhci-4bit"; reg = <0x0 0x04fb0000 0x0 0x1000>, <0x0 0x4fb8000 0x0 0x400>; interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; power-domains = <&k3_pds 92 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 92 0>, <&k3_clks 92 5>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 92 5>, <&k3_clks 92 0>; assigned-clocks = <&k3_clks 92 0>; assigned-clock-parents = <&k3_clks 92 1>; ti,otap-del-sel-legacy = <0x0>; @@ -1110,13 +1074,13 @@ dma-coherent; }; - main_sdhci2: sdhci@4f98000 { + main_sdhci2: mmc@4f98000 { compatible = "ti,j721e-sdhci-4bit"; reg = <0x0 0x4f98000 0x0 0x1000>, <0x0 0x4f90000 0x0 0x400>; interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; power-domains = <&k3_pds 93 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 93 0>, <&k3_clks 93 5>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 93 5>, <&k3_clks 93 0>; assigned-clocks = <&k3_clks 93 0>; assigned-clock-parents = <&k3_clks 93 1>; ti,otap-del-sel-legacy = <0x0>; diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi index cc483f7344af..f0587fde147e 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi @@ -115,7 +115,7 @@ }; pmu: pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a72-pmu"; /* Recommendation from GIC500 TRM Table A.3 */ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts index ed0bf7f13f54..37da418393e0 100644 --- a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts +++ b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts @@ -41,3 +41,8 @@ clocks = <&uart_clk>; clock-names = "apb_pclk"; }; + +&wdt { + status = "okay"; + clocks = <&wdt_clk>; +}; diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi index 242f25f4e12a..c360e68bef1d 100644 --- a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi +++ b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi @@ -134,6 +134,12 @@ #clock-cells = <0>; }; + wdt_clk: wdt-clk { + compatible = "fixed-clock"; + clock-frequency = <150000000>; + #clock-cells = <0>; + }; + soc { #address-cells = <2>; #size-cells = <2>; @@ -384,6 +390,12 @@ #size-cells = <0>; status = "disabled"; }; + + wdt: wdt@28330000 { + compatible = "toshiba,visconti-wdt"; + reg = <0 0x28330000 0 0x1000>; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile index 60f5443f3ef4..11fb4fd3ebd4 100644 --- a/arch/arm64/boot/dts/xilinx/Makefile +++ b/arch/arm64/boot/dts/xilinx/Makefile @@ -13,5 +13,6 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb +dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index c94c3bb67edc..cf5295224750 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -116,6 +116,10 @@ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>; }; +&nand0 { + clocks = <&zynqmp_clk NAND_REF>, <&zynqmp_clk LPD_LSBUS>; +}; + &gem0 { clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>, <&zynqmp_clk GEM0_TX>, <&zynqmp_clk GEM0_RX>, @@ -160,6 +164,10 @@ clocks = <&zynqmp_clk PCIE_REF>; }; +&qspi { + clocks = <&zynqmp_clk QSPI_REF>, <&zynqmp_clk LPD_LSBUS>; +}; + &sata { clocks = <&zynqmp_clk SATA_REF>; }; @@ -215,3 +223,17 @@ &watchdog0 { clocks = <&zynqmp_clk WDT>; }; + +&lpd_watchdog { + clocks = <&zynqmp_clk LPD_WDT>; +}; + +&zynqmp_dpdma { + clocks = <&zynqmp_clk DPDMA_REF>; +}; + +&zynqmp_dpsub { + clocks = <&zynqmp_clk TOPSW_LSBUS>, + <&zynqmp_clk DP_AUDIO_REF>, + <&zynqmp_clk DP_VIDEO_REF>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts index 68ecd0f7b2f2..a53598c3624b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts @@ -15,6 +15,7 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU100 RevC"; @@ -108,6 +109,18 @@ compatible = "iio-hwmon"; io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>; }; + + si5335a_0: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + si5335a_1: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; }; &dcc { @@ -224,6 +237,13 @@ }; }; +&psgtr { + status = "okay"; + /* usb3, dps */ + clocks = <&si5335a_0>, <&si5335a_1>; + clock-names = "ref0", "ref1"; +}; + &rtc { status = "okay"; }; @@ -233,11 +253,13 @@ status = "okay"; no-1-8-v; disable-wp; + xlnx,mio-bank = <0>; }; &sdhci1 { status = "okay"; bus-width = <0x4>; + xlnx,mio-bank = <0>; non-removable; disable-wp; cap-power-off-card; @@ -293,3 +315,14 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 1>, + <&psgtr 0 PHY_TYPE_DP 1 1>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index f1255f635dfd..12e8bd48dc8c 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -13,6 +13,7 @@ #include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU102 RevA"; @@ -132,6 +133,19 @@ compatible = "iio-hwmon"; io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>; }; + + /* 48MHz reference crystal */ + ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; + + refhdmi: refhdmi { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <114285000>; + }; }; &can1 { @@ -483,9 +497,56 @@ #size-cells = <0>; reg = <1>; si5341: clock-generator@36 { /* SI5341 - u69 */ + compatible = "silabs,si5341"; reg = <0x36>; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + clock-output-names = "si5341"; + + si5341_0: out@0 { + /* refclk0 for PS-GT, used for DP */ + reg = <0>; + always-on; + }; + si5341_2: out@2 { + /* refclk2 for PS-GT, used for USB3 */ + reg = <2>; + always-on; + }; + si5341_3: out@3 { + /* refclk3 for PS-GT, used for SATA */ + reg = <3>; + always-on; + }; + si5341_4: out@4 { + /* refclk4 for PS-GT, used for PCIE slot */ + reg = <4>; + always-on; + }; + si5341_5: out@5 { + /* refclk5 for PS-GT, used for PCIE */ + reg = <5>; + always-on; + }; + si5341_6: out@6 { + /* refclk6 PL CLK125 */ + reg = <6>; + always-on; + }; + si5341_7: out@7 { + /* refclk7 PL CLK74 */ + reg = <7>; + always-on; + }; + si5341_9: out@9 { + /* refclk9 used for PS_REF_CLK 33.3 MHz */ + reg = <9>; + always-on; + }; }; - }; i2c@2 { #address-cells = <1>; @@ -526,6 +587,17 @@ * interrupt-parent = <&>; * interrupts = <>; */ + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + clocks = <&refhdmi>; + clock-names = "xtal"; + clock-output-names = "si5328"; + + si5328_clk: clk0@0 { + reg = <0>; + clock-frequency = <27000000>; + }; }; }; /* 5 - 7 unconnected */ @@ -592,6 +664,13 @@ status = "okay"; }; +&psgtr { + status = "okay"; + /* pcie, sata, usb3, dp */ + clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>; + clock-names = "ref0", "ref1", "ref2", "ref3"; +}; + &rtc { status = "okay"; }; @@ -607,12 +686,15 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; }; &uart0 { @@ -632,3 +714,13 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index 7a4614e3f5fa..5637e1c17fdf 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -12,6 +12,7 @@ #include "zynqmp.dtsi" #include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU104 RevA"; @@ -36,6 +37,24 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + clock_8t49n287_5: clk125 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clock_8t49n287_2: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + clock_8t49n287_3: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; }; &can1 { @@ -158,6 +177,13 @@ status = "okay"; }; +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; + clock-names = "ref1", "ref2", "ref3"; +}; + &sata { status = "okay"; /* SATA OOB timing settings */ @@ -169,12 +195,15 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; disable-wp; }; @@ -195,3 +224,14 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts new file mode 100644 index 000000000000..7f2e32831b05 --- /dev/null +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts @@ -0,0 +1,293 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Xilinx ZynqMP ZCU104 + * + * (C) Copyright 2017 - 2020, Xilinx, Inc. + * + * Michal Simek <michal.simek@xilinx.com> + */ + +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> + +/ { + model = "ZynqMP ZCU104 RevC"; + compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp"; + + aliases { + ethernet0 = &gem3; + i2c0 = &i2c1; + mmc0 = &sdhci1; + rtc0 = &rtc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &dcc; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + ina226 { + compatible = "iio-hwmon"; + io-channels = <&u183 0>, <&u183 1>, <&u183 2>, <&u183 3>; + }; + + clock_8t49n287_5: clk125 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clock_8t49n287_2: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + clock_8t49n287_3: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; +}; + +&can1 { + status = "okay"; +}; + +&dcc { + status = "okay"; +}; + +&fpd_dma_chan1 { + status = "okay"; +}; + +&fpd_dma_chan2 { + status = "okay"; +}; + +&fpd_dma_chan3 { + status = "okay"; +}; + +&fpd_dma_chan4 { + status = "okay"; +}; + +&fpd_dma_chan5 { + status = "okay"; +}; + +&fpd_dma_chan6 { + status = "okay"; +}; + +&fpd_dma_chan7 { + status = "okay"; +}; + +&fpd_dma_chan8 { + status = "okay"; +}; + +&gem3 { + status = "okay"; + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; + phy0: ethernet-phy@c { + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + }; +}; + +&gpio { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tca6416_u97: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + /* + * IRQ not connected + * Lines: + * 0 - IRPS5401_ALERT_B + * 1 - HDMI_8T49N241_INT_ALM + * 2 - MAX6643_OT_B + * 3 - MAX6643_FANFAIL_B + * 5 - IIC_MUX_RESET_B + * 6 - GEM3_EXP_RESET_B + * 7 - FMC_LPC_PRSNT_M2C_B + * 4, 10 - 17 - not connected + */ + }; + + /* Another connection to this bus via PL i2c via PCA9306 - u45 */ + i2c-mux@74 { /* u34 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + /* + * IIC_EEPROM 1kB memory which uses 256B blocks + * where every block has different address. + * 0 - 256B address 0x54 + * 256B - 512B address 0x55 + * 512B - 768B address 0x56 + * 768B - 1024B address 0x57 + */ + eeprom: eeprom@54 { /* u23 */ + compatible = "atmel,24c08"; + reg = <0x54>; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */ + reg = <0x6c>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + irps5401_43: irps5401@43 { /* IRPS5401 - u175 */ + compatible = "infineon,irps5401"; + reg = <0x43>; /* pmbus / i2c 0x13 */ + }; + irps5401_44: irps5401@44 { /* IRPS5401 - u180 */ + compatible = "infineon,irps5401"; + reg = <0x44>; /* pmbus / i2c 0x14 */ + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + u183: ina226@40 { /* u183 */ + compatible = "ti,ina226"; + #io-channel-cells = <1>; + reg = <0x40>; + shunt-resistor = <5000>; + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; + + /* 4, 6 not connected */ + }; +}; + +&qspi { + status = "okay"; + flash@0 { + compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + }; +}; + +&rtc { + status = "okay"; +}; + +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; + clock-names = "ref1", "ref2", "ref3"; +}; + +&sata { + status = "okay"; + /* SATA OOB timing settings */ + ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; + ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; + ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; + ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; + ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; +}; + +/* SD1 with level shifter */ +&sdhci1 { + status = "okay"; + no-1-8-v; + xlnx,mio-bank = <1>; + disable-wp; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +/* ULPI SMSC USB3320 */ +&usb0 { + status = "okay"; + dr_mode = "host"; +}; + +&watchdog0 { + status = "okay"; +}; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index 6e9efe233838..18771e868399 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -13,6 +13,7 @@ #include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU106 RevA"; @@ -132,6 +133,19 @@ compatible = "iio-hwmon"; io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>; }; + + /* 48MHz reference crystal */ + ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; + + refhdmi: refhdmi { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <114285000>; + }; }; &can1 { @@ -142,6 +156,17 @@ status = "okay"; }; +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; + /* fpd_dma clk 667MHz, lpd_dma 500MHz */ &fpd_dma_chan1 { status = "okay"; @@ -482,7 +507,45 @@ #size-cells = <0>; reg = <1>; si5341: clock-generator@36 { /* SI5341 - u69 */ + compatible = "silabs,si5341"; reg = <0x36>; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + clock-output-names = "si5341"; + + si5341_0: out@0 { + /* refclk0 for PS-GT, used for DP */ + reg = <0>; + always-on; + }; + si5341_2: out@2 { + /* refclk2 for PS-GT, used for USB3 */ + reg = <2>; + always-on; + }; + si5341_3: out@3 { + /* refclk3 for PS-GT, used for SATA */ + reg = <3>; + always-on; + }; + si5341_6: out@6 { + /* refclk6 PL CLK125 */ + reg = <6>; + always-on; + }; + si5341_7: out@7 { + /* refclk7 PL CLK74 */ + reg = <7>; + always-on; + }; + si5341_9: out@9 { + /* refclk9 used for PS_REF_CLK 33.3 MHz */ + reg = <9>; + always-on; + }; }; }; @@ -520,6 +583,22 @@ reg = <4>; si5328: clock-generator@69 {/* SI5328 - u20 */ reg = <0x69>; + /* + * Chip has interrupt present connected to PL + * interrupt-parent = <&>; + * interrupts = <>; + */ + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + clocks = <&refhdmi>; + clock-names = "xtal"; + clock-output-names = "si5328"; + + si5328_clk: clk0@0 { + reg = <0>; + clock-frequency = <27000000>; + }; }; }; i2c@5 { @@ -591,6 +670,13 @@ }; }; +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>; + clock-names = "ref1", "ref2", "ref3"; +}; + &rtc { status = "okay"; }; @@ -606,12 +692,15 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; }; &uart0 { diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index 2e92634c77f9..d4b68f0d0098 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -13,6 +13,7 @@ #include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU111 RevA"; @@ -116,6 +117,13 @@ compatible = "iio-hwmon"; io-channels = <&u79 0>, <&u79 1>, <&u79 2>, <&u79 3>; }; + + /* 48MHz reference crystal */ + ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; }; &dcc { @@ -374,9 +382,46 @@ #size-cells = <0>; reg = <1>; si5341: clock-generator@36 { /* SI5341 - u46 */ + compatible = "silabs,si5341"; reg = <0x36>; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + clock-output-names = "si5341"; + + si5341_0: out@0 { + /* refclk0 for PS-GT, used for DP */ + reg = <0>; + always-on; + }; + si5341_2: out@2 { + /* refclk2 for PS-GT, used for USB3 */ + reg = <2>; + always-on; + }; + si5341_3: out@3 { + /* refclk3 for PS-GT, used for SATA */ + reg = <3>; + always-on; + }; + si5341_5: out@5 { + /* refclk5 PL CLK100 */ + reg = <5>; + always-on; + }; + si5341_6: out@6 { + /* refclk6 PL CLK125 */ + reg = <6>; + always-on; + }; + si5341_9: out@9 { + /* refclk9 used for PS_REF_CLK 33.3 MHz */ + reg = <9>; + always-on; + }; }; - }; i2c@2 { #address-cells = <1>; @@ -410,7 +455,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <4>; - si5328: clock-generator@69 { /* SI5328 - u48 */ + si5382: clock-generator@69 { /* SI5382 - u48 */ reg = <0x69>; }; }; @@ -497,6 +542,13 @@ }; }; +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>; + clock-names = "ref1", "ref2", "ref3"; +}; + &rtc { status = "okay"; }; @@ -512,12 +564,15 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; }; &uart0 { @@ -529,3 +584,14 @@ status = "okay"; dr_mode = "host"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 1>, + <&psgtr 0 PHY_TYPE_DP 1 1>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 68923fbd0e89..a3b391d18787 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -12,6 +12,7 @@ * the License, or (at your option) any later version. */ +#include <dt-bindings/dma/xlnx-zynqmp-dpdma.h> #include <dt-bindings/power/xlnx-zynqmp-power.h> #include <dt-bindings/reset/xlnx-zynqmp-resets.h> @@ -99,7 +100,7 @@ }; }; - zynqmp_ipi { + zynqmp_ipi: zynqmp_ipi { compatible = "xlnx,zynqmp-ipi-mailbox"; interrupt-parent = <&gic>; interrupts = <0 35 4>; @@ -187,6 +188,11 @@ xlnx_aes: zynqmp-aes { compatible = "xlnx,zynqmp-aes"; }; + + zynqmp_reset: reset-controller { + compatible = "xlnx,zynqmp-reset"; + #reset-cells = <1>; + }; }; }; @@ -265,6 +271,8 @@ interrupts = <0 124 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14e8>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -276,6 +284,8 @@ interrupts = <0 125 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14e9>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -287,6 +297,8 @@ interrupts = <0 126 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ea>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -298,6 +310,8 @@ interrupts = <0 127 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14eb>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -309,6 +323,8 @@ interrupts = <0 128 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ec>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -320,6 +336,8 @@ interrupts = <0 129 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ed>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -331,6 +349,8 @@ interrupts = <0 130 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ee>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -342,11 +362,14 @@ interrupts = <0 131 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ef>; power-domains = <&zynqmp_firmware PD_GDMA>; }; gic: interrupt-controller@f9010000 { compatible = "arm,gic-400"; + #address-cells = <0>; #interrupt-cells = <3>; reg = <0x0 0xf9010000 0x0 0x10000>, <0x0 0xf9020000 0x0 0x20000>, @@ -369,6 +392,8 @@ interrupts = <0 77 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x868>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -380,6 +405,8 @@ interrupts = <0 78 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x869>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -391,6 +418,8 @@ interrupts = <0 79 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86a>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -402,6 +431,8 @@ interrupts = <0 80 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86b>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -413,6 +444,8 @@ interrupts = <0 81 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86c>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -424,6 +457,8 @@ interrupts = <0 82 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86d>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -435,6 +470,8 @@ interrupts = <0 83 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86e>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -446,6 +483,8 @@ interrupts = <0 84 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86f>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -456,6 +495,20 @@ interrupts = <0 112 4>; }; + nand0: nand-controller@ff100000 { + compatible = "xlnx,zynqmp-nand-controller", "arasan,nfc-v3p10"; + status = "disabled"; + reg = <0x0 0xff100000 0x0 0x1000>; + clock-names = "controller", "bus"; + interrupt-parent = <&gic>; + interrupts = <0 14 4>; + #address-cells = <1>; + #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x872>; + power-domains = <&zynqmp_firmware PD_NAND>; + }; + gem0: ethernet@ff0b0000 { compatible = "cdns,zynqmp-gem", "cdns,gem"; status = "disabled"; @@ -465,6 +518,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x874>; power-domains = <&zynqmp_firmware PD_ETH_0>; }; @@ -477,6 +532,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x875>; power-domains = <&zynqmp_firmware PD_ETH_1>; }; @@ -489,6 +546,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x876>; power-domains = <&zynqmp_firmware PD_ETH_2>; }; @@ -501,12 +560,15 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x877>; power-domains = <&zynqmp_firmware PD_ETH_3>; }; gpio: gpio@ff0a0000 { compatible = "xlnx,zynqmp-gpio-1.0"; status = "disabled"; + #address-cells = <0>; #gpio-cells = <0x2>; gpio-controller; interrupt-parent = <&gic>; @@ -576,6 +638,22 @@ }; }; + qspi: spi@ff0f0000 { + compatible = "xlnx,zynqmp-qspi-1.0"; + status = "disabled"; + clock-names = "ref_clk", "pclk"; + interrupts = <0 15 4>; + interrupt-parent = <&gic>; + num-cs = <1>; + reg = <0x0 0xff0f0000 0x0 0x1000>, + <0x0 0xc0000000 0x0 0x8000000>; + #address-cells = <1>; + #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x873>; + power-domains = <&zynqmp_firmware PD_QSPI>; + }; + psgtr: phy@fd400000 { compatible = "xlnx,zynqmp-psgtr-v1.1"; status = "disabled"; @@ -602,6 +680,9 @@ interrupt-parent = <&gic>; interrupts = <0 133 4>; power-domains = <&zynqmp_firmware PD_SATA>; + #stream-id-cells = <4>; + iommus = <&smmu 0x4c0>, <&smmu 0x4c1>, + <&smmu 0x4c2>, <&smmu 0x4c3>; }; sdhci0: mmc@ff160000 { @@ -611,6 +692,8 @@ interrupts = <0 48 4>; reg = <0x0 0xff160000 0x0 0x1000>; clock-names = "clk_xin", "clk_ahb"; + #stream-id-cells = <1>; + iommus = <&smmu 0x870>; #clock-cells = <1>; clock-output-names = "clk_out_sd0", "clk_in_sd0"; power-domains = <&zynqmp_firmware PD_SD_0>; @@ -623,6 +706,8 @@ interrupts = <0 49 4>; reg = <0x0 0xff170000 0x0 0x1000>; clock-names = "clk_xin", "clk_ahb"; + #stream-id-cells = <1>; + iommus = <&smmu 0x871>; #clock-cells = <1>; clock-output-names = "clk_out_sd1", "clk_in_sd1"; power-domains = <&zynqmp_firmware PD_SD_1>; @@ -631,6 +716,7 @@ smmu: iommu@fd800000 { compatible = "arm,mmu-500"; reg = <0x0 0xfd800000 0x0 0x20000>; + #iommu-cells = <1>; status = "disabled"; #global-interrupts = <1>; interrupt-parent = <&gic>; @@ -753,5 +839,45 @@ reg = <0x0 0xfd4d0000 0x0 0x1000>; timeout-sec = <10>; }; + + lpd_watchdog: watchdog@ff150000 { + compatible = "cdns,wdt-r1p2"; + status = "disabled"; + interrupt-parent = <&gic>; + interrupts = <0 52 1>; + reg = <0x0 0xff150000 0x0 0x1000>; + timeout-sec = <10>; + }; + + zynqmp_dpdma: dma-controller@fd4c0000 { + compatible = "xlnx,zynqmp-dpdma"; + status = "disabled"; + reg = <0x0 0xfd4c0000 0x0 0x1000>; + interrupts = <0 122 4>; + interrupt-parent = <&gic>; + clock-names = "axi_clk"; + #dma-cells = <1>; + }; + + zynqmp_dpsub: display@fd4a0000 { + compatible = "xlnx,zynqmp-dpsub-1.7"; + status = "disabled"; + reg = <0x0 0xfd4a0000 0x0 0x1000>, + <0x0 0xfd4aa000 0x0 0x1000>, + <0x0 0xfd4ab000 0x0 0x1000>, + <0x0 0xfd4ac000 0x0 0x1000>; + reg-names = "dp", "blend", "av_buf", "aud"; + interrupts = <0 119 4>; + interrupt-parent = <&gic>; + clock-names = "dp_apb_clk", "dp_aud_clk", + "dp_vtc_pixel_clk_in"; + power-domains = <&zynqmp_firmware PD_DP>; + resets = <&zynqmp_reset ZYNQMP_RESET_DP>; + dma-names = "vid0", "vid1", "vid2", "gfx0"; + dmas = <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO0>, + <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO1>, + <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO2>, + <&zynqmp_dpdma ZYNQMP_DPDMA_GRAPHICS>; + }; }; }; diff --git a/arch/arm64/include/asm/Kbuild b/arch/arm64/include/asm/Kbuild index ff9cbb631212..07ac208edc89 100644 --- a/arch/arm64/include/asm/Kbuild +++ b/arch/arm64/include/asm/Kbuild @@ -1,6 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 generic-y += early_ioremap.h -generic-y += local64.h generic-y += mcs_spinlock.h generic-y += qrwlock.h generic-y += qspinlock.h |