diff options
Diffstat (limited to 'Documentation')
152 files changed, 7556 insertions, 5053 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-mtd b/Documentation/ABI/testing/sysfs-class-mtd index 3b5c3bca9186..f34e592301d1 100644 --- a/Documentation/ABI/testing/sysfs-class-mtd +++ b/Documentation/ABI/testing/sysfs-class-mtd @@ -229,6 +229,6 @@ KernelVersion: 4.1 Contact: linux-mtd@lists.infradead.org Description: For a partition, the offset of that partition from the start - of the master device in bytes. This attribute is absent on - main devices, so it can be used to distinguish between - partitions and devices that aren't partitions. + of the parent (another partition or a flash device) in bytes. + This attribute is absent on flash devices, so it can be used + to distinguish them from partitions. diff --git a/Documentation/ABI/testing/sysfs-fs-f2fs b/Documentation/ABI/testing/sysfs-fs-f2fs index a809f6005f14..84c606fb3ca4 100644 --- a/Documentation/ABI/testing/sysfs-fs-f2fs +++ b/Documentation/ABI/testing/sysfs-fs-f2fs @@ -75,7 +75,7 @@ Contact: "Jaegeuk Kim" <jaegeuk.kim@samsung.com> Description: Controls the memory footprint used by f2fs. -What: /sys/fs/f2fs/<disk>/trim_sections +What: /sys/fs/f2fs/<disk>/batched_trim_sections Date: February 2015 Contact: "Jaegeuk Kim" <jaegeuk@kernel.org> Description: @@ -112,3 +112,21 @@ Date: January 2016 Contact: "Shuoran Liu" <liushuoran@huawei.com> Description: Shows total written kbytes issued to disk. + +What: /sys/fs/f2fs/<disk>/inject_rate +Date: May 2016 +Contact: "Sheng Yong" <shengyong1@huawei.com> +Description: + Controls the injection rate. + +What: /sys/fs/f2fs/<disk>/inject_type +Date: May 2016 +Contact: "Sheng Yong" <shengyong1@huawei.com> +Description: + Controls the injection type. + +What: /sys/fs/f2fs/<disk>/reserved_blocks +Date: June 2017 +Contact: "Chao Yu" <yuchao0@huawei.com> +Description: + Controls current reserved blocks in system. diff --git a/Documentation/DMA-API-HOWTO.txt b/Documentation/DMA-API-HOWTO.txt index 4ed388356898..f0cc3f772265 100644 --- a/Documentation/DMA-API-HOWTO.txt +++ b/Documentation/DMA-API-HOWTO.txt @@ -1,22 +1,24 @@ - Dynamic DMA mapping Guide - ========================= +========================= +Dynamic DMA mapping Guide +========================= - David S. Miller <davem@redhat.com> - Richard Henderson <rth@cygnus.com> - Jakub Jelinek <jakub@redhat.com> +:Author: David S. Miller <davem@redhat.com> +:Author: Richard Henderson <rth@cygnus.com> +:Author: Jakub Jelinek <jakub@redhat.com> This is a guide to device driver writers on how to use the DMA API with example pseudo-code. For a concise description of the API, see DMA-API.txt. - CPU and DMA addresses +CPU and DMA addresses +===================== There are several kinds of addresses involved in the DMA API, and it's important to understand the differences. The kernel normally uses virtual addresses. Any address returned by kmalloc(), vmalloc(), and similar interfaces is a virtual address and can -be stored in a "void *". +be stored in a ``void *``. The virtual memory system (TLB, page tables, etc.) translates virtual addresses to CPU physical addresses, which are stored as "phys_addr_t" or @@ -37,7 +39,7 @@ be restricted to a subset of that space. For example, even if a system supports 64-bit addresses for main memory and PCI BARs, it may use an IOMMU so devices only need to use 32-bit DMA addresses. -Here's a picture and some examples: +Here's a picture and some examples:: CPU CPU Bus Virtual Physical Address @@ -98,15 +100,16 @@ microprocessor architecture. You should use the DMA API rather than the bus-specific DMA API, i.e., use the dma_map_*() interfaces rather than the pci_map_*() interfaces. -First of all, you should make sure +First of all, you should make sure:: -#include <linux/dma-mapping.h> + #include <linux/dma-mapping.h> is in your driver, which provides the definition of dma_addr_t. This type can hold any valid DMA address for the platform and should be used everywhere you hold a DMA address returned from the DMA mapping functions. - What memory is DMA'able? +What memory is DMA'able? +======================== The first piece of information you must know is what kernel memory can be used with the DMA mapping facilities. There has been an unwritten @@ -143,7 +146,8 @@ What about block I/O and networking buffers? The block I/O and networking subsystems make sure that the buffers they use are valid for you to DMA from/to. - DMA addressing limitations +DMA addressing limitations +========================== Does your device have any DMA addressing limitations? For example, is your device only capable of driving the low order 24-bits of address? @@ -166,7 +170,7 @@ style to do this even if your device holds the default setting, because this shows that you did think about these issues wrt. your device. -The query is performed via a call to dma_set_mask_and_coherent(): +The query is performed via a call to dma_set_mask_and_coherent():: int dma_set_mask_and_coherent(struct device *dev, u64 mask); @@ -175,12 +179,12 @@ If you have some special requirements, then the following two separate queries can be used instead: The query for streaming mappings is performed via a call to - dma_set_mask(): + dma_set_mask():: int dma_set_mask(struct device *dev, u64 mask); The query for consistent allocations is performed via a call - to dma_set_coherent_mask(): + to dma_set_coherent_mask():: int dma_set_coherent_mask(struct device *dev, u64 mask); @@ -209,7 +213,7 @@ of your driver reports that performance is bad or that the device is not even detected, you can ask them for the kernel messages to find out exactly why. -The standard 32-bit addressing device would do something like this: +The standard 32-bit addressing device would do something like this:: if (dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32))) { dev_warn(dev, "mydev: No suitable DMA available\n"); @@ -225,7 +229,7 @@ than 64-bit addressing. For example, Sparc64 PCI SAC addressing is more efficient than DAC addressing. Here is how you would handle a 64-bit capable device which can drive -all 64-bits when accessing streaming DMA: +all 64-bits when accessing streaming DMA:: int using_dac; @@ -239,7 +243,7 @@ all 64-bits when accessing streaming DMA: } If a card is capable of using 64-bit consistent allocations as well, -the case would look like this: +the case would look like this:: int using_dac, consistent_using_dac; @@ -260,7 +264,7 @@ uses consistent allocations, one would have to check the return value from dma_set_coherent_mask(). Finally, if your device can only drive the low 24-bits of -address you might do something like: +address you might do something like:: if (dma_set_mask(dev, DMA_BIT_MASK(24))) { dev_warn(dev, "mydev: 24-bit DMA addressing not available\n"); @@ -280,7 +284,7 @@ only provide the functionality which the machine can handle. It is important that the last call to dma_set_mask() be for the most specific mask. -Here is pseudo-code showing how this might be done: +Here is pseudo-code showing how this might be done:: #define PLAYBACK_ADDRESS_BITS DMA_BIT_MASK(32) #define RECORD_ADDRESS_BITS DMA_BIT_MASK(24) @@ -308,7 +312,8 @@ A sound card was used as an example here because this genre of PCI devices seems to be littered with ISA chips given a PCI front end, and thus retaining the 16MB DMA addressing limitations of ISA. - Types of DMA mappings +Types of DMA mappings +===================== There are two types of DMA mappings: @@ -336,12 +341,14 @@ There are two types of DMA mappings: to memory is immediately visible to the device, and vice versa. Consistent mappings guarantee this. - IMPORTANT: Consistent DMA memory does not preclude the usage of - proper memory barriers. The CPU may reorder stores to + .. important:: + + Consistent DMA memory does not preclude the usage of + proper memory barriers. The CPU may reorder stores to consistent memory just as it may normal memory. Example: if it is important for the device to see the first word of a descriptor updated before the second, you must do - something like: + something like:: desc->word0 = address; wmb(); @@ -377,16 +384,17 @@ Also, systems with caches that aren't DMA-coherent will work better when the underlying buffers don't share cache lines with other data. - Using Consistent DMA mappings. +Using Consistent DMA mappings +============================= To allocate and map large (PAGE_SIZE or so) consistent DMA regions, -you should do: +you should do:: dma_addr_t dma_handle; cpu_addr = dma_alloc_coherent(dev, size, &dma_handle, gfp); -where device is a struct device *. This may be called in interrupt +where device is a ``struct device *``. This may be called in interrupt context with the GFP_ATOMIC flag. Size is the length of the region you want to allocate, in bytes. @@ -415,7 +423,7 @@ exists (for example) to guarantee that if you allocate a chunk which is smaller than or equal to 64 kilobytes, the extent of the buffer you receive will not cross a 64K boundary. -To unmap and free such a DMA region, you call: +To unmap and free such a DMA region, you call:: dma_free_coherent(dev, size, cpu_addr, dma_handle); @@ -430,7 +438,7 @@ a kmem_cache, but it uses dma_alloc_coherent(), not __get_free_pages(). Also, it understands common hardware constraints for alignment, like queue heads needing to be aligned on N byte boundaries. -Create a dma_pool like this: +Create a dma_pool like this:: struct dma_pool *pool; @@ -444,7 +452,7 @@ pass 0 for boundary; passing 4096 says memory allocated from this pool must not cross 4KByte boundaries (but at that time it may be better to use dma_alloc_coherent() directly instead). -Allocate memory from a DMA pool like this: +Allocate memory from a DMA pool like this:: cpu_addr = dma_pool_alloc(pool, flags, &dma_handle); @@ -452,7 +460,7 @@ flags are GFP_KERNEL if blocking is permitted (not in_interrupt nor holding SMP locks), GFP_ATOMIC otherwise. Like dma_alloc_coherent(), this returns two values, cpu_addr and dma_handle. -Free memory that was allocated from a dma_pool like this: +Free memory that was allocated from a dma_pool like this:: dma_pool_free(pool, cpu_addr, dma_handle); @@ -460,7 +468,7 @@ where pool is what you passed to dma_pool_alloc(), and cpu_addr and dma_handle are the values dma_pool_alloc() returned. This function may be called in interrupt context. -Destroy a dma_pool by calling: +Destroy a dma_pool by calling:: dma_pool_destroy(pool); @@ -468,11 +476,12 @@ Make sure you've called dma_pool_free() for all memory allocated from a pool before you destroy the pool. This function may not be called in interrupt context. - DMA Direction +DMA Direction +============= The interfaces described in subsequent portions of this document take a DMA direction argument, which is an integer and takes on -one of the following values: +one of the following values:: DMA_BIDIRECTIONAL DMA_TO_DEVICE @@ -521,14 +530,15 @@ packets, map/unmap them with the DMA_TO_DEVICE direction specifier. For receive packets, just the opposite, map/unmap them with the DMA_FROM_DEVICE direction specifier. - Using Streaming DMA mappings +Using Streaming DMA mappings +============================ The streaming DMA mapping routines can be called from interrupt context. There are two versions of each map/unmap, one which will map/unmap a single memory region, and one which will map/unmap a scatterlist. -To map a single region, you do: +To map a single region, you do:: struct device *dev = &my_dev->dev; dma_addr_t dma_handle; @@ -545,7 +555,7 @@ To map a single region, you do: goto map_error_handling; } -and to unmap it: +and to unmap it:: dma_unmap_single(dev, dma_handle, size, direction); @@ -563,7 +573,7 @@ Using CPU pointers like this for single mappings has a disadvantage: you cannot reference HIGHMEM memory in this way. Thus, there is a map/unmap interface pair akin to dma_{map,unmap}_single(). These interfaces deal with page/offset pairs instead of CPU pointers. -Specifically: +Specifically:: struct device *dev = &my_dev->dev; dma_addr_t dma_handle; @@ -593,7 +603,7 @@ error as outlined under the dma_map_single() discussion. You should call dma_unmap_page() when the DMA activity is finished, e.g., from the interrupt which told you that the DMA transfer is done. -With scatterlists, you map a region gathered from several regions by: +With scatterlists, you map a region gathered from several regions by:: int i, count = dma_map_sg(dev, sglist, nents, direction); struct scatterlist *sg; @@ -617,16 +627,18 @@ Then you should loop count times (note: this can be less than nents times) and use sg_dma_address() and sg_dma_len() macros where you previously accessed sg->address and sg->length as shown above. -To unmap a scatterlist, just call: +To unmap a scatterlist, just call:: dma_unmap_sg(dev, sglist, nents, direction); Again, make sure DMA activity has already finished. -PLEASE NOTE: The 'nents' argument to the dma_unmap_sg call must be - the _same_ one you passed into the dma_map_sg call, - it should _NOT_ be the 'count' value _returned_ from the - dma_map_sg call. +.. note:: + + The 'nents' argument to the dma_unmap_sg call must be + the _same_ one you passed into the dma_map_sg call, + it should _NOT_ be the 'count' value _returned_ from the + dma_map_sg call. Every dma_map_{single,sg}() call should have its dma_unmap_{single,sg}() counterpart, because the DMA address space is a shared resource and @@ -638,11 +650,11 @@ properly in order for the CPU and device to see the most up-to-date and correct copy of the DMA buffer. So, firstly, just map it with dma_map_{single,sg}(), and after each DMA -transfer call either: +transfer call either:: dma_sync_single_for_cpu(dev, dma_handle, size, direction); -or: +or:: dma_sync_sg_for_cpu(dev, sglist, nents, direction); @@ -650,17 +662,19 @@ as appropriate. Then, if you wish to let the device get at the DMA area again, finish accessing the data with the CPU, and then before actually -giving the buffer to the hardware call either: +giving the buffer to the hardware call either:: dma_sync_single_for_device(dev, dma_handle, size, direction); -or: +or:: dma_sync_sg_for_device(dev, sglist, nents, direction); as appropriate. -PLEASE NOTE: The 'nents' argument to dma_sync_sg_for_cpu() and +.. note:: + + The 'nents' argument to dma_sync_sg_for_cpu() and dma_sync_sg_for_device() must be the same passed to dma_map_sg(). It is _NOT_ the count returned by dma_map_sg(). @@ -671,7 +685,7 @@ dma_map_*() call till dma_unmap_*(), then you don't have to call the dma_sync_*() routines at all. Here is pseudo code which shows a situation in which you would need -to use the dma_sync_*() interfaces. +to use the dma_sync_*() interfaces:: my_card_setup_receive_buffer(struct my_card *cp, char *buffer, int len) { @@ -747,7 +761,8 @@ is planned to completely remove virt_to_bus() and bus_to_virt() as they are entirely deprecated. Some ports already do not provide these as it is impossible to correctly support them. - Handling Errors +Handling Errors +=============== DMA address space is limited on some architectures and an allocation failure can be determined by: @@ -755,7 +770,7 @@ failure can be determined by: - checking if dma_alloc_coherent() returns NULL or dma_map_sg returns 0 - checking the dma_addr_t returned from dma_map_single() and dma_map_page() - by using dma_mapping_error(): + by using dma_mapping_error():: dma_addr_t dma_handle; @@ -773,7 +788,8 @@ failure can be determined by: of a multiple page mapping attempt. These example are applicable to dma_map_page() as well. -Example 1: +Example 1:: + dma_addr_t dma_handle1; dma_addr_t dma_handle2; @@ -802,8 +818,12 @@ Example 1: dma_unmap_single(dma_handle1); map_error_handling1: -Example 2: (if buffers are allocated in a loop, unmap all mapped buffers when - mapping error is detected in the middle) +Example 2:: + + /* + * if buffers are allocated in a loop, unmap all mapped buffers when + * mapping error is detected in the middle + */ dma_addr_t dma_addr; dma_addr_t array[DMA_BUFFERS]; @@ -846,7 +866,8 @@ SCSI drivers must return SCSI_MLQUEUE_HOST_BUSY if the DMA mapping fails in the queuecommand hook. This means that the SCSI subsystem passes the command to the driver again later. - Optimizing Unmap State Space Consumption +Optimizing Unmap State Space Consumption +======================================== On many platforms, dma_unmap_{single,page}() is simply a nop. Therefore, keeping track of the mapping address and length is a waste @@ -858,7 +879,7 @@ Actually, instead of describing the macros one by one, we'll transform some example code. 1) Use DEFINE_DMA_UNMAP_{ADDR,LEN} in state saving structures. - Example, before: + Example, before:: struct ring_state { struct sk_buff *skb; @@ -866,7 +887,7 @@ transform some example code. __u32 len; }; - after: + after:: struct ring_state { struct sk_buff *skb; @@ -875,23 +896,23 @@ transform some example code. }; 2) Use dma_unmap_{addr,len}_set() to set these values. - Example, before: + Example, before:: ringp->mapping = FOO; ringp->len = BAR; - after: + after:: dma_unmap_addr_set(ringp, mapping, FOO); dma_unmap_len_set(ringp, len, BAR); 3) Use dma_unmap_{addr,len}() to access these values. - Example, before: + Example, before:: dma_unmap_single(dev, ringp->mapping, ringp->len, DMA_FROM_DEVICE); - after: + after:: dma_unmap_single(dev, dma_unmap_addr(ringp, mapping), @@ -902,7 +923,8 @@ It really should be self-explanatory. We treat the ADDR and LEN separately, because it is possible for an implementation to only need the address in order to perform the unmap operation. - Platform Issues +Platform Issues +=============== If you are just writing drivers for Linux and do not maintain an architecture port for the kernel, you can safely skip down @@ -928,12 +950,13 @@ to "Closing". alignment constraints (e.g. the alignment constraints about 64-bit objects). - Closing +Closing +======= This document, and the API itself, would not be in its current form without the feedback and suggestions from numerous individuals. We would like to specifically mention, in no particular order, the -following people: +following people:: Russell King <rmk@arm.linux.org.uk> Leo Dagum <dagum@barrel.engr.sgi.com> diff --git a/Documentation/DMA-API.txt b/Documentation/DMA-API.txt index 71200dfa0922..45b29326d719 100644 --- a/Documentation/DMA-API.txt +++ b/Documentation/DMA-API.txt @@ -1,7 +1,8 @@ - Dynamic DMA mapping using the generic device - ============================================ +============================================ +Dynamic DMA mapping using the generic device +============================================ - James E.J. Bottomley <James.Bottomley@HansenPartnership.com> +:Author: James E.J. Bottomley <James.Bottomley@HansenPartnership.com> This document describes the DMA API. For a more gentle introduction of the API (and actual examples), see Documentation/DMA-API-HOWTO.txt. @@ -12,10 +13,10 @@ machines. Unless you know that your driver absolutely has to support non-consistent platforms (this is usually only legacy platforms) you should only use the API described in part I. -Part I - dma_ API -------------------------------------- +Part I - dma_API +---------------- -To get the dma_ API, you must #include <linux/dma-mapping.h>. This +To get the dma_API, you must #include <linux/dma-mapping.h>. This provides dma_addr_t and the interfaces described below. A dma_addr_t can hold any valid DMA address for the platform. It can be @@ -26,9 +27,11 @@ address space and the DMA address space. Part Ia - Using large DMA-coherent buffers ------------------------------------------ -void * -dma_alloc_coherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) +:: + + void * + dma_alloc_coherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) Consistent memory is memory for which a write by either the device or the processor can immediately be read by the processor or device @@ -51,20 +54,24 @@ consolidate your requests for consistent memory as much as possible. The simplest way to do that is to use the dma_pool calls (see below). The flag parameter (dma_alloc_coherent() only) allows the caller to -specify the GFP_ flags (see kmalloc()) for the allocation (the +specify the ``GFP_`` flags (see kmalloc()) for the allocation (the implementation may choose to ignore flags that affect the location of the returned memory, like GFP_DMA). -void * -dma_zalloc_coherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) +:: + + void * + dma_zalloc_coherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) Wraps dma_alloc_coherent() and also zeroes the returned memory if the allocation attempt succeeded. -void -dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, - dma_addr_t dma_handle) +:: + + void + dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, + dma_addr_t dma_handle) Free a region of consistent memory you previously allocated. dev, size and dma_handle must all be the same as those passed into @@ -78,7 +85,7 @@ may only be called with IRQs enabled. Part Ib - Using small DMA-coherent buffers ------------------------------------------ -To get this part of the dma_ API, you must #include <linux/dmapool.h> +To get this part of the dma_API, you must #include <linux/dmapool.h> Many drivers need lots of small DMA-coherent memory regions for DMA descriptors or I/O buffers. Rather than allocating in units of a page @@ -88,6 +95,8 @@ not __get_free_pages(). Also, they understand common hardware constraints for alignment, like queue heads needing to be aligned on N-byte boundaries. +:: + struct dma_pool * dma_pool_create(const char *name, struct device *dev, size_t size, size_t align, size_t alloc); @@ -103,16 +112,21 @@ in bytes, and must be a power of two). If your device has no boundary crossing restrictions, pass 0 for alloc; passing 4096 says memory allocated from this pool must not cross 4KByte boundaries. +:: - void *dma_pool_zalloc(struct dma_pool *pool, gfp_t mem_flags, - dma_addr_t *handle) + void * + dma_pool_zalloc(struct dma_pool *pool, gfp_t mem_flags, + dma_addr_t *handle) Wraps dma_pool_alloc() and also zeroes the returned memory if the allocation attempt succeeded. - void *dma_pool_alloc(struct dma_pool *pool, gfp_t gfp_flags, - dma_addr_t *dma_handle); +:: + + void * + dma_pool_alloc(struct dma_pool *pool, gfp_t gfp_flags, + dma_addr_t *dma_handle); This allocates memory from the pool; the returned memory will meet the size and alignment requirements specified at creation time. Pass @@ -122,16 +136,20 @@ blocking. Like dma_alloc_coherent(), this returns two values: an address usable by the CPU, and the DMA address usable by the pool's device. +:: - void dma_pool_free(struct dma_pool *pool, void *vaddr, - dma_addr_t addr); + void + dma_pool_free(struct dma_pool *pool, void *vaddr, + dma_addr_t addr); This puts memory back into the pool. The pool is what was passed to dma_pool_alloc(); the CPU (vaddr) and DMA addresses are what were returned when that routine allocated the memory being freed. +:: - void dma_pool_destroy(struct dma_pool *pool); + void + dma_pool_destroy(struct dma_pool *pool); dma_pool_destroy() frees the resources of the pool. It must be called in a context which can sleep. Make sure you've freed all allocated @@ -141,32 +159,40 @@ memory back to the pool before you destroy it. Part Ic - DMA addressing limitations ------------------------------------ -int -dma_set_mask_and_coherent(struct device *dev, u64 mask) +:: + + int + dma_set_mask_and_coherent(struct device *dev, u64 mask) Checks to see if the mask is possible and updates the device streaming and coherent DMA mask parameters if it is. Returns: 0 if successful and a negative error if not. -int -dma_set_mask(struct device *dev, u64 mask) +:: + + int + dma_set_mask(struct device *dev, u64 mask) Checks to see if the mask is possible and updates the device parameters if it is. Returns: 0 if successful and a negative error if not. -int -dma_set_coherent_mask(struct device *dev, u64 mask) +:: + + int + dma_set_coherent_mask(struct device *dev, u64 mask) Checks to see if the mask is possible and updates the device parameters if it is. Returns: 0 if successful and a negative error if not. -u64 -dma_get_required_mask(struct device *dev) +:: + + u64 + dma_get_required_mask(struct device *dev) This API returns the mask that the platform requires to operate efficiently. Usually this means the returned mask @@ -182,94 +208,107 @@ call to set the mask to the value returned. Part Id - Streaming DMA mappings -------------------------------- -dma_addr_t -dma_map_single(struct device *dev, void *cpu_addr, size_t size, - enum dma_data_direction direction) +:: + + dma_addr_t + dma_map_single(struct device *dev, void *cpu_addr, size_t size, + enum dma_data_direction direction) Maps a piece of processor virtual memory so it can be accessed by the device and returns the DMA address of the memory. The direction for both APIs may be converted freely by casting. -However the dma_ API uses a strongly typed enumerator for its +However the dma_API uses a strongly typed enumerator for its direction: +======================= ============================================= DMA_NONE no direction (used for debugging) DMA_TO_DEVICE data is going from the memory to the device DMA_FROM_DEVICE data is coming from the device to the memory DMA_BIDIRECTIONAL direction isn't known +======================= ============================================= + +.. note:: + + Not all memory regions in a machine can be mapped by this API. + Further, contiguous kernel virtual space may not be contiguous as + physical memory. Since this API does not provide any scatter/gather + capability, it will fail if the user tries to map a non-physically + contiguous piece of memory. For this reason, memory to be mapped by + this API should be obtained from sources which guarantee it to be + physically contiguous (like kmalloc). + + Further, the DMA address of the memory must be within the + dma_mask of the device (the dma_mask is a bit mask of the + addressable region for the device, i.e., if the DMA address of + the memory ANDed with the dma_mask is still equal to the DMA + address, then the device can perform DMA to the memory). To + ensure that the memory allocated by kmalloc is within the dma_mask, + the driver may specify various platform-dependent flags to restrict + the DMA address range of the allocation (e.g., on x86, GFP_DMA + guarantees to be within the first 16MB of available DMA addresses, + as required by ISA devices). + + Note also that the above constraints on physical contiguity and + dma_mask may not apply if the platform has an IOMMU (a device which + maps an I/O DMA address to a physical memory address). However, to be + portable, device driver writers may *not* assume that such an IOMMU + exists. + +.. warning:: + + Memory coherency operates at a granularity called the cache + line width. In order for memory mapped by this API to operate + correctly, the mapped region must begin exactly on a cache line + boundary and end exactly on one (to prevent two separately mapped + regions from sharing a single cache line). Since the cache line size + may not be known at compile time, the API will not enforce this + requirement. Therefore, it is recommended that driver writers who + don't take special care to determine the cache line size at run time + only map virtual regions that begin and end on page boundaries (which + are guaranteed also to be cache line boundaries). + + DMA_TO_DEVICE synchronisation must be done after the last modification + of the memory region by the software and before it is handed off to + the device. Once this primitive is used, memory covered by this + primitive should be treated as read-only by the device. If the device + may write to it at any point, it should be DMA_BIDIRECTIONAL (see + below). + + DMA_FROM_DEVICE synchronisation must be done before the driver + accesses data that may be changed by the device. This memory should + be treated as read-only by the driver. If the driver needs to write + to it at any point, it should be DMA_BIDIRECTIONAL (see below). + + DMA_BIDIRECTIONAL requires special handling: it means that the driver + isn't sure if the memory was modified before being handed off to the + device and also isn't sure if the device will also modify it. Thus, + you must always sync bidirectional memory twice: once before the + memory is handed off to the device (to make sure all memory changes + are flushed from the processor) and once before the data may be + accessed after being used by the device (to make sure any processor + cache lines are updated with data that the device may have changed). + +:: -Notes: Not all memory regions in a machine can be mapped by this API. -Further, contiguous kernel virtual space may not be contiguous as -physical memory. Since this API does not provide any scatter/gather -capability, it will fail if the user tries to map a non-physically -contiguous piece of memory. For this reason, memory to be mapped by -this API should be obtained from sources which guarantee it to be -physically contiguous (like kmalloc). - -Further, the DMA address of the memory must be within the -dma_mask of the device (the dma_mask is a bit mask of the -addressable region for the device, i.e., if the DMA address of -the memory ANDed with the dma_mask is still equal to the DMA -address, then the device can perform DMA to the memory). To -ensure that the memory allocated by kmalloc is within the dma_mask, -the driver may specify various platform-dependent flags to restrict -the DMA address range of the allocation (e.g., on x86, GFP_DMA -guarantees to be within the first 16MB of available DMA addresses, -as required by ISA devices). - -Note also that the above constraints on physical contiguity and -dma_mask may not apply if the platform has an IOMMU (a device which -maps an I/O DMA address to a physical memory address). However, to be -portable, device driver writers may *not* assume that such an IOMMU -exists. - -Warnings: Memory coherency operates at a granularity called the cache -line width. In order for memory mapped by this API to operate -correctly, the mapped region must begin exactly on a cache line -boundary and end exactly on one (to prevent two separately mapped -regions from sharing a single cache line). Since the cache line size -may not be known at compile time, the API will not enforce this -requirement. Therefore, it is recommended that driver writers who -don't take special care to determine the cache line size at run time -only map virtual regions that begin and end on page boundaries (which -are guaranteed also to be cache line boundaries). - -DMA_TO_DEVICE synchronisation must be done after the last modification -of the memory region by the software and before it is handed off to -the device. Once this primitive is used, memory covered by this -primitive should be treated as read-only by the device. If the device -may write to it at any point, it should be DMA_BIDIRECTIONAL (see -below). - -DMA_FROM_DEVICE synchronisation must be done before the driver -accesses data that may be changed by the device. This memory should -be treated as read-only by the driver. If the driver needs to write -to it at any point, it should be DMA_BIDIRECTIONAL (see below). - -DMA_BIDIRECTIONAL requires special handling: it means that the driver -isn't sure if the memory was modified before being handed off to the -device and also isn't sure if the device will also modify it. Thus, -you must always sync bidirectional memory twice: once before the -memory is handed off to the device (to make sure all memory changes -are flushed from the processor) and once before the data may be -accessed after being used by the device (to make sure any processor -cache lines are updated with data that the device may have changed). - -void -dma_unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, - enum dma_data_direction direction) + void + dma_unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, + enum dma_data_direction direction) Unmaps the region previously mapped. All the parameters passed in must be identical to those passed in (and returned) by the mapping API. -dma_addr_t -dma_map_page(struct device *dev, struct page *page, - unsigned long offset, size_t size, - enum dma_data_direction direction) -void -dma_unmap_page(struct device *dev, dma_addr_t dma_address, size_t size, - enum dma_data_direction direction) +:: + + dma_addr_t + dma_map_page(struct device *dev, struct page *page, + unsigned long offset, size_t size, + enum dma_data_direction direction) + + void + dma_unmap_page(struct device *dev, dma_addr_t dma_address, size_t size, + enum dma_data_direction direction) API for mapping and unmapping for pages. All the notes and warnings for the other mapping APIs apply here. Also, although the <offset> @@ -277,20 +316,24 @@ and <size> parameters are provided to do partial page mapping, it is recommended that you never use these unless you really know what the cache width is. -dma_addr_t -dma_map_resource(struct device *dev, phys_addr_t phys_addr, size_t size, - enum dma_data_direction dir, unsigned long attrs) +:: -void -dma_unmap_resource(struct device *dev, dma_addr_t addr, size_t size, - enum dma_data_direction dir, unsigned long attrs) + dma_addr_t + dma_map_resource(struct device *dev, phys_addr_t phys_addr, size_t size, + enum dma_data_direction dir, unsigned long attrs) + + void + dma_unmap_resource(struct device *dev, dma_addr_t addr, size_t size, + enum dma_data_direction dir, unsigned long attrs) API for mapping and unmapping for MMIO resources. All the notes and warnings for the other mapping APIs apply here. The API should only be used to map device MMIO resources, mapping of RAM is not permitted. -int -dma_mapping_error(struct device *dev, dma_addr_t dma_addr) +:: + + int + dma_mapping_error(struct device *dev, dma_addr_t dma_addr) In some circumstances dma_map_single(), dma_map_page() and dma_map_resource() will fail to create a mapping. A driver can check for these errors by testing @@ -298,9 +341,11 @@ the returned DMA address with dma_mapping_error(). A non-zero return value means the mapping could not be created and the driver should take appropriate action (e.g. reduce current DMA mapping usage or delay and try again later). +:: + int dma_map_sg(struct device *dev, struct scatterlist *sg, - int nents, enum dma_data_direction direction) + int nents, enum dma_data_direction direction) Returns: the number of DMA address segments mapped (this may be shorter than <nents> passed in if some elements of the scatter/gather list are @@ -316,7 +361,7 @@ critical that the driver do something, in the case of a block driver aborting the request or even oopsing is better than doing nothing and corrupting the filesystem. -With scatterlists, you use the resulting mapping like this: +With scatterlists, you use the resulting mapping like this:: int i, count = dma_map_sg(dev, sglist, nents, direction); struct scatterlist *sg; @@ -337,9 +382,11 @@ Then you should loop count times (note: this can be less than nents times) and use sg_dma_address() and sg_dma_len() macros where you previously accessed sg->address and sg->length as shown above. +:: + void dma_unmap_sg(struct device *dev, struct scatterlist *sg, - int nents, enum dma_data_direction direction) + int nents, enum dma_data_direction direction) Unmap the previously mapped scatter/gather list. All the parameters must be the same as those and passed in to the scatter/gather mapping @@ -348,18 +395,27 @@ API. Note: <nents> must be the number you passed in, *not* the number of DMA address entries returned. -void -dma_sync_single_for_cpu(struct device *dev, dma_addr_t dma_handle, size_t size, - enum dma_data_direction direction) -void -dma_sync_single_for_device(struct device *dev, dma_addr_t dma_handle, size_t size, - enum dma_data_direction direction) -void -dma_sync_sg_for_cpu(struct device *dev, struct scatterlist *sg, int nents, - enum dma_data_direction direction) -void -dma_sync_sg_for_device(struct device *dev, struct scatterlist *sg, int nents, - enum dma_data_direction direction) +:: + + void + dma_sync_single_for_cpu(struct device *dev, dma_addr_t dma_handle, + size_t size, + enum dma_data_direction direction) + + void + dma_sync_single_for_device(struct device *dev, dma_addr_t dma_handle, + size_t size, + enum dma_data_direction direction) + + void + dma_sync_sg_for_cpu(struct device *dev, struct scatterlist *sg, + int nents, + enum dma_data_direction direction) + + void + dma_sync_sg_for_device(struct device *dev, struct scatterlist *sg, + int nents, + enum dma_data_direction direction) Synchronise a single contiguous or scatter/gather mapping for the CPU and device. With the sync_sg API, all the parameters must be the same @@ -367,36 +423,41 @@ as those passed into the single mapping API. With the sync_single API, you can use dma_handle and size parameters that aren't identical to those passed into the single mapping API to do a partial sync. -Notes: You must do this: -- Before reading values that have been written by DMA from the device - (use the DMA_FROM_DEVICE direction) -- After writing values that will be written to the device using DMA - (use the DMA_TO_DEVICE) direction -- before *and* after handing memory to the device if the memory is - DMA_BIDIRECTIONAL +.. note:: + + You must do this: + + - Before reading values that have been written by DMA from the device + (use the DMA_FROM_DEVICE direction) + - After writing values that will be written to the device using DMA + (use the DMA_TO_DEVICE) direction + - before *and* after handing memory to the device if the memory is + DMA_BIDIRECTIONAL See also dma_map_single(). -dma_addr_t -dma_map_single_attrs(struct device *dev, void *cpu_addr, size_t size, - enum dma_data_direction dir, - unsigned long attrs) +:: + + dma_addr_t + dma_map_single_attrs(struct device *dev, void *cpu_addr, size_t size, + enum dma_data_direction dir, + unsigned long attrs) -void -dma_unmap_single_attrs(struct device *dev, dma_addr_t dma_addr, - size_t size, enum dma_data_direction dir, - unsigned long attrs) + void + dma_unmap_single_attrs(struct device *dev, dma_addr_t dma_addr, + size_t size, enum dma_data_direction dir, + unsigned long attrs) -int -dma_map_sg_attrs(struct device *dev, struct scatterlist *sgl, - int nents, enum dma_data_direction dir, - unsigned long attrs) + int + dma_map_sg_attrs(struct device *dev, struct scatterlist *sgl, + int nents, enum dma_data_direction dir, + unsigned long attrs) -void -dma_unmap_sg_attrs(struct device *dev, struct scatterlist *sgl, - int nents, enum dma_data_direction dir, - unsigned long attrs) + void + dma_unmap_sg_attrs(struct device *dev, struct scatterlist *sgl, + int nents, enum dma_data_direction dir, + unsigned long attrs) The four functions above are just like the counterpart functions without the _attrs suffixes, except that they pass an optional @@ -410,37 +471,38 @@ is identical to those of the corresponding function without the _attrs suffix. As a result dma_map_single_attrs() can generally replace dma_map_single(), etc. -As an example of the use of the *_attrs functions, here's how +As an example of the use of the ``*_attrs`` functions, here's how you could pass an attribute DMA_ATTR_FOO when mapping memory -for DMA: +for DMA:: -#include <linux/dma-mapping.h> -/* DMA_ATTR_FOO should be defined in linux/dma-mapping.h and - * documented in Documentation/DMA-attributes.txt */ -... + #include <linux/dma-mapping.h> + /* DMA_ATTR_FOO should be defined in linux/dma-mapping.h and + * documented in Documentation/DMA-attributes.txt */ + ... - unsigned long attr; - attr |= DMA_ATTR_FOO; - .... - n = dma_map_sg_attrs(dev, sg, nents, DMA_TO_DEVICE, attr); - .... + unsigned long attr; + attr |= DMA_ATTR_FOO; + .... + n = dma_map_sg_attrs(dev, sg, nents, DMA_TO_DEVICE, attr); + .... Architectures that care about DMA_ATTR_FOO would check for its presence in their implementations of the mapping and unmapping -routines, e.g.: - -void whizco_dma_map_sg_attrs(struct device *dev, dma_addr_t dma_addr, - size_t size, enum dma_data_direction dir, - unsigned long attrs) -{ - .... - if (attrs & DMA_ATTR_FOO) - /* twizzle the frobnozzle */ - .... +routines, e.g.::: + + void whizco_dma_map_sg_attrs(struct device *dev, dma_addr_t dma_addr, + size_t size, enum dma_data_direction dir, + unsigned long attrs) + { + .... + if (attrs & DMA_ATTR_FOO) + /* twizzle the frobnozzle */ + .... + } -Part II - Advanced dma_ usage ------------------------------ +Part II - Advanced dma usage +---------------------------- Warning: These pieces of the DMA API should not be used in the majority of cases, since they cater for unlikely corner cases that @@ -450,9 +512,11 @@ If you don't understand how cache line coherency works between a processor and an I/O device, you should not be using this part of the API at all. -void * -dma_alloc_noncoherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) +:: + + void * + dma_alloc_noncoherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) Identical to dma_alloc_coherent() except that the platform will choose to return either consistent or non-consistent memory as it sees @@ -468,39 +532,49 @@ only use this API if you positively know your driver will be required to work on one of the rare (usually non-PCI) architectures that simply cannot make consistent memory. -void -dma_free_noncoherent(struct device *dev, size_t size, void *cpu_addr, - dma_addr_t dma_handle) +:: + + void + dma_free_noncoherent(struct device *dev, size_t size, void *cpu_addr, + dma_addr_t dma_handle) Free memory allocated by the nonconsistent API. All parameters must be identical to those passed in (and returned by dma_alloc_noncoherent()). -int -dma_get_cache_alignment(void) +:: + + int + dma_get_cache_alignment(void) Returns the processor cache alignment. This is the absolute minimum alignment *and* width that you must observe when either mapping memory or doing partial flushes. -Notes: This API may return a number *larger* than the actual cache -line, but it will guarantee that one or more cache lines fit exactly -into the width returned by this call. It will also always be a power -of two for easy alignment. +.. note:: -void -dma_cache_sync(struct device *dev, void *vaddr, size_t size, - enum dma_data_direction direction) + This API may return a number *larger* than the actual cache + line, but it will guarantee that one or more cache lines fit exactly + into the width returned by this call. It will also always be a power + of two for easy alignment. + +:: + + void + dma_cache_sync(struct device *dev, void *vaddr, size_t size, + enum dma_data_direction direction) Do a partial sync of memory that was allocated by dma_alloc_noncoherent(), starting at virtual address vaddr and continuing on for size. Again, you *must* observe the cache line boundaries when doing this. -int -dma_declare_coherent_memory(struct device *dev, phys_addr_t phys_addr, - dma_addr_t device_addr, size_t size, int - flags) +:: + + int + dma_declare_coherent_memory(struct device *dev, phys_addr_t phys_addr, + dma_addr_t device_addr, size_t size, int + flags) Declare region of memory to be handed out by dma_alloc_coherent() when it's asked for coherent memory for this device. @@ -516,21 +590,21 @@ size is the size of the area (must be multiples of PAGE_SIZE). flags can be ORed together and are: -DMA_MEMORY_MAP - request that the memory returned from -dma_alloc_coherent() be directly writable. +- DMA_MEMORY_MAP - request that the memory returned from + dma_alloc_coherent() be directly writable. -DMA_MEMORY_IO - request that the memory returned from -dma_alloc_coherent() be addressable using read()/write()/memcpy_toio() etc. +- DMA_MEMORY_IO - request that the memory returned from + dma_alloc_coherent() be addressable using read()/write()/memcpy_toio() etc. One or both of these flags must be present. -DMA_MEMORY_INCLUDES_CHILDREN - make the declared memory be allocated by -dma_alloc_coherent of any child devices of this one (for memory residing -on a bridge). +- DMA_MEMORY_INCLUDES_CHILDREN - make the declared memory be allocated by + dma_alloc_coherent of any child devices of this one (for memory residing + on a bridge). -DMA_MEMORY_EXCLUSIVE - only allocate memory from the declared regions. -Do not allow dma_alloc_coherent() to fall back to system memory when -it's out of memory in the declared region. +- DMA_MEMORY_EXCLUSIVE - only allocate memory from the declared regions. + Do not allow dma_alloc_coherent() to fall back to system memory when + it's out of memory in the declared region. The return value will be either DMA_MEMORY_MAP or DMA_MEMORY_IO and must correspond to a passed in flag (i.e. no returning DMA_MEMORY_IO @@ -543,15 +617,17 @@ must be accessed using the correct bus functions. If your driver isn't prepared to handle this contingency, it should not specify DMA_MEMORY_IO in the input flags. -As a simplification for the platforms, only *one* such region of +As a simplification for the platforms, only **one** such region of memory may be declared per device. For reasons of efficiency, most platforms choose to track the declared region only at the granularity of a page. For smaller allocations, you should use the dma_pool() API. -void -dma_release_declared_memory(struct device *dev) +:: + + void + dma_release_declared_memory(struct device *dev) Remove the memory region previously declared from the system. This API performs *no* in-use checking for this region and will return @@ -559,9 +635,11 @@ unconditionally having removed all the required structures. It is the driver's job to ensure that no parts of this memory region are currently in use. -void * -dma_mark_declared_memory_occupied(struct device *dev, - dma_addr_t device_addr, size_t size) +:: + + void * + dma_mark_declared_memory_occupied(struct device *dev, + dma_addr_t device_addr, size_t size) This is used to occupy specific regions of the declared space (dma_alloc_coherent() will hand out the first free region it finds). @@ -592,38 +670,37 @@ option has a performance impact. Do not enable it in production kernels. If you boot the resulting kernel will contain code which does some bookkeeping about what DMA memory was allocated for which device. If this code detects an error it prints a warning message with some details into your kernel log. An -example warning message may look like this: - -------------[ cut here ]------------ -WARNING: at /data2/repos/linux-2.6-iommu/lib/dma-debug.c:448 - check_unmap+0x203/0x490() -Hardware name: -forcedeth 0000:00:08.0: DMA-API: device driver frees DMA memory with wrong - function [device address=0x00000000640444be] [size=66 bytes] [mapped as -single] [unmapped as page] -Modules linked in: nfsd exportfs bridge stp llc r8169 -Pid: 0, comm: swapper Tainted: G W 2.6.28-dmatest-09289-g8bb99c0 #1 -Call Trace: - <IRQ> [<ffffffff80240b22>] warn_slowpath+0xf2/0x130 - [<ffffffff80647b70>] _spin_unlock+0x10/0x30 - [<ffffffff80537e75>] usb_hcd_link_urb_to_ep+0x75/0xc0 - [<ffffffff80647c22>] _spin_unlock_irqrestore+0x12/0x40 - [<ffffffff8055347f>] ohci_urb_enqueue+0x19f/0x7c0 - [<ffffffff80252f96>] queue_work+0x56/0x60 - [<ffffffff80237e10>] enqueue_task_fair+0x20/0x50 - [<ffffffff80539279>] usb_hcd_submit_urb+0x379/0xbc0 - [<ffffffff803b78c3>] cpumask_next_and+0x23/0x40 - [<ffffffff80235177>] find_busiest_group+0x207/0x8a0 - [<ffffffff8064784f>] _spin_lock_irqsave+0x1f/0x50 - [<ffffffff803c7ea3>] check_unmap+0x203/0x490 - [<ffffffff803c8259>] debug_dma_unmap_page+0x49/0x50 - [<ffffffff80485f26>] nv_tx_done_optimized+0xc6/0x2c0 - [<ffffffff80486c13>] nv_nic_irq_optimized+0x73/0x2b0 - [<ffffffff8026df84>] handle_IRQ_event+0x34/0x70 - [<ffffffff8026ffe9>] handle_edge_irq+0xc9/0x150 - [<ffffffff8020e3ab>] do_IRQ+0xcb/0x1c0 - [<ffffffff8020c093>] ret_from_intr+0x0/0xa - <EOI> <4>---[ end trace f6435a98e2a38c0e ]--- +example warning message may look like this:: + + WARNING: at /data2/repos/linux-2.6-iommu/lib/dma-debug.c:448 + check_unmap+0x203/0x490() + Hardware name: + forcedeth 0000:00:08.0: DMA-API: device driver frees DMA memory with wrong + function [device address=0x00000000640444be] [size=66 bytes] [mapped as + single] [unmapped as page] + Modules linked in: nfsd exportfs bridge stp llc r8169 + Pid: 0, comm: swapper Tainted: G W 2.6.28-dmatest-09289-g8bb99c0 #1 + Call Trace: + <IRQ> [<ffffffff80240b22>] warn_slowpath+0xf2/0x130 + [<ffffffff80647b70>] _spin_unlock+0x10/0x30 + [<ffffffff80537e75>] usb_hcd_link_urb_to_ep+0x75/0xc0 + [<ffffffff80647c22>] _spin_unlock_irqrestore+0x12/0x40 + [<ffffffff8055347f>] ohci_urb_enqueue+0x19f/0x7c0 + [<ffffffff80252f96>] queue_work+0x56/0x60 + [<ffffffff80237e10>] enqueue_task_fair+0x20/0x50 + [<ffffffff80539279>] usb_hcd_submit_urb+0x379/0xbc0 + [<ffffffff803b78c3>] cpumask_next_and+0x23/0x40 + [<ffffffff80235177>] find_busiest_group+0x207/0x8a0 + [<ffffffff8064784f>] _spin_lock_irqsave+0x1f/0x50 + [<ffffffff803c7ea3>] check_unmap+0x203/0x490 + [<ffffffff803c8259>] debug_dma_unmap_page+0x49/0x50 + [<ffffffff80485f26>] nv_tx_done_optimized+0xc6/0x2c0 + [<ffffffff80486c13>] nv_nic_irq_optimized+0x73/0x2b0 + [<ffffffff8026df84>] handle_IRQ_event+0x34/0x70 + [<ffffffff8026ffe9>] handle_edge_irq+0xc9/0x150 + [<ffffffff8020e3ab>] do_IRQ+0xcb/0x1c0 + [<ffffffff8020c093>] ret_from_intr+0x0/0xa + <EOI> <4>---[ end trace f6435a98e2a38c0e ]--- The driver developer can find the driver and the device including a stacktrace of the DMA-API call which caused this warning. @@ -637,43 +714,42 @@ details. The debugfs directory for the DMA-API debugging code is called dma-api/. In this directory the following files can currently be found: - dma-api/all_errors This file contains a numeric value. If this +=============================== =============================================== +dma-api/all_errors This file contains a numeric value. If this value is not equal to zero the debugging code will print a warning for every error it finds into the kernel log. Be careful with this option, as it can easily flood your logs. - dma-api/disabled This read-only file contains the character 'Y' +dma-api/disabled This read-only file contains the character 'Y' if the debugging code is disabled. This can happen when it runs out of memory or if it was disabled at boot time - dma-api/error_count This file is read-only and shows the total +dma-api/error_count This file is read-only and shows the total numbers of errors found. - dma-api/num_errors The number in this file shows how many +dma-api/num_errors The number in this file shows how many warnings will be printed to the kernel log before it stops. This number is initialized to one at system boot and be set by writing into this file - dma-api/min_free_entries - This read-only file can be read to get the +dma-api/min_free_entries This read-only file can be read to get the minimum number of free dma_debug_entries the allocator has ever seen. If this value goes down to zero the code will disable itself because it is not longer reliable. - dma-api/num_free_entries - The current number of free dma_debug_entries +dma-api/num_free_entries The current number of free dma_debug_entries in the allocator. - dma-api/driver-filter - You can write a name of a driver into this file +dma-api/driver-filter You can write a name of a driver into this file to limit the debug output to requests from that particular driver. Write an empty string to that file to disable the filter and see all errors again. +=============================== =============================================== If you have this code compiled into your kernel it will be enabled by default. If you want to boot without the bookkeeping anyway you can provide @@ -692,7 +768,10 @@ of preallocated entries is defined per architecture. If it is too low for you boot with 'dma_debug_entries=<your_desired_number>' to overwrite the architectural default. -void debug_dma_mapping_error(struct device *dev, dma_addr_t dma_addr); +:: + + void + debug_dma_mapping_error(struct device *dev, dma_addr_t dma_addr); dma-debug interface debug_dma_mapping_error() to debug drivers that fail to check DMA mapping errors on addresses returned by dma_map_single() and @@ -702,4 +781,3 @@ the driver. When driver does unmap, debug_dma_unmap() checks the flag and if this flag is still set, prints warning message that includes call trace that leads up to the unmap. This interface can be called from dma_mapping_error() routines to enable DMA mapping error check debugging. - diff --git a/Documentation/DMA-ISA-LPC.txt b/Documentation/DMA-ISA-LPC.txt index c41331398752..8c2b8be6e45b 100644 --- a/Documentation/DMA-ISA-LPC.txt +++ b/Documentation/DMA-ISA-LPC.txt @@ -1,19 +1,20 @@ - DMA with ISA and LPC devices - ============================ +============================ +DMA with ISA and LPC devices +============================ - Pierre Ossman <drzeus@drzeus.cx> +:Author: Pierre Ossman <drzeus@drzeus.cx> This document describes how to do DMA transfers using the old ISA DMA controller. Even though ISA is more or less dead today the LPC bus uses the same DMA system so it will be around for quite some time. -Part I - Headers and dependencies ---------------------------------- +Headers and dependencies +------------------------ -To do ISA style DMA you need to include two headers: +To do ISA style DMA you need to include two headers:: -#include <linux/dma-mapping.h> -#include <asm/dma.h> + #include <linux/dma-mapping.h> + #include <asm/dma.h> The first is the generic DMA API used to convert virtual addresses to bus addresses (see Documentation/DMA-API.txt for details). @@ -23,8 +24,8 @@ this is not present on all platforms make sure you construct your Kconfig to be dependent on ISA_DMA_API (not ISA) so that nobody tries to build your driver on unsupported platforms. -Part II - Buffer allocation ---------------------------- +Buffer allocation +----------------- The ISA DMA controller has some very strict requirements on which memory it can access so extra care must be taken when allocating @@ -42,13 +43,13 @@ requirements you pass the flag GFP_DMA to kmalloc. Unfortunately the memory available for ISA DMA is scarce so unless you allocate the memory during boot-up it's a good idea to also pass -__GFP_REPEAT and __GFP_NOWARN to make the allocator try a bit harder. +__GFP_RETRY_MAYFAIL and __GFP_NOWARN to make the allocator try a bit harder. (This scarcity also means that you should allocate the buffer as early as possible and not release it until the driver is unloaded.) -Part III - Address translation ------------------------------- +Address translation +------------------- To translate the virtual address to a bus address, use the normal DMA API. Do _not_ use isa_virt_to_phys() even though it does the same @@ -61,8 +62,8 @@ Note: x86_64 had a broken DMA API when it came to ISA but has since been fixed. If your arch has problems then fix the DMA API instead of reverting to the ISA functions. -Part IV - Channels ------------------- +Channels +-------- A normal ISA DMA controller has 8 channels. The lower four are for 8-bit transfers and the upper four are for 16-bit transfers. @@ -80,8 +81,8 @@ The ability to use 16-bit or 8-bit transfers is _not_ up to you as a driver author but depends on what the hardware supports. Check your specs or test different channels. -Part V - Transfer data ----------------------- +Transfer data +------------- Now for the good stuff, the actual DMA transfer. :) @@ -112,37 +113,37 @@ Once the DMA transfer is finished (or timed out) you should disable the channel again. You should also check get_dma_residue() to make sure that all data has been transferred. -Example: +Example:: -int flags, residue; + int flags, residue; -flags = claim_dma_lock(); + flags = claim_dma_lock(); -clear_dma_ff(); + clear_dma_ff(); -set_dma_mode(channel, DMA_MODE_WRITE); -set_dma_addr(channel, phys_addr); -set_dma_count(channel, num_bytes); + set_dma_mode(channel, DMA_MODE_WRITE); + set_dma_addr(channel, phys_addr); + set_dma_count(channel, num_bytes); -dma_enable(channel); + dma_enable(channel); -release_dma_lock(flags); + release_dma_lock(flags); -while (!device_done()); + while (!device_done()); -flags = claim_dma_lock(); + flags = claim_dma_lock(); -dma_disable(channel); + dma_disable(channel); -residue = dma_get_residue(channel); -if (residue != 0) - printk(KERN_ERR "driver: Incomplete DMA transfer!" - " %d bytes left!\n", residue); + residue = dma_get_residue(channel); + if (residue != 0) + printk(KERN_ERR "driver: Incomplete DMA transfer!" + " %d bytes left!\n", residue); -release_dma_lock(flags); + release_dma_lock(flags); -Part VI - Suspend/resume ------------------------- +Suspend/resume +-------------- It is the driver's responsibility to make sure that the machine isn't suspended while a DMA transfer is in progress. Also, all DMA settings diff --git a/Documentation/DMA-attributes.txt b/Documentation/DMA-attributes.txt index 44c6bc496eee..8f8d97f65d73 100644 --- a/Documentation/DMA-attributes.txt +++ b/Documentation/DMA-attributes.txt @@ -1,5 +1,6 @@ - DMA attributes - ============== +============== +DMA attributes +============== This document describes the semantics of the DMA attributes that are defined in linux/dma-mapping.h. @@ -108,6 +109,7 @@ This is a hint to the DMA-mapping subsystem that it's probably not worth the time to try to allocate memory to in a way that gives better TLB efficiency (AKA it's not worth trying to build the mapping out of larger pages). You might want to specify this if: + - You know that the accesses to this memory won't thrash the TLB. You might know that the accesses are likely to be sequential or that they aren't sequential but it's unlikely you'll ping-pong @@ -121,11 +123,12 @@ pages). You might want to specify this if: the mapping to have a short lifetime then it may be worth it to optimize allocation (avoid coming up with large pages) instead of getting the slight performance win of larger pages. + Setting this hint doesn't guarantee that you won't get huge pages, but it means that we won't try quite as hard to get them. -NOTE: At the moment DMA_ATTR_ALLOC_SINGLE_PAGES is only implemented on ARM, -though ARM64 patches will likely be posted soon. +.. note:: At the moment DMA_ATTR_ALLOC_SINGLE_PAGES is only implemented on ARM, + though ARM64 patches will likely be posted soon. DMA_ATTR_NO_WARN ---------------- @@ -142,10 +145,10 @@ problem at all, depending on the implementation of the retry mechanism. So, this provides a way for drivers to avoid those error messages on calls where allocation failures are not a problem, and shouldn't bother the logs. -NOTE: At the moment DMA_ATTR_NO_WARN is only implemented on PowerPC. +.. note:: At the moment DMA_ATTR_NO_WARN is only implemented on PowerPC. DMA_ATTR_PRIVILEGED ------------------------------- +------------------- Some advanced peripherals such as remote processors and GPUs perform accesses to DMA buffers in both privileged "supervisor" and unprivileged diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 6962cab997ef..aa77a25a0940 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -1,9 +1,8 @@ +===================== +The Linux IPMI Driver +===================== - The Linux IPMI Driver - --------------------- - Corey Minyard - <minyard@mvista.com> - <minyard@acm.org> +:Author: Corey Minyard <minyard@mvista.com> / <minyard@acm.org> The Intelligent Platform Management Interface, or IPMI, is a standard for controlling intelligent devices that monitor a system. @@ -141,7 +140,7 @@ Addressing ---------- The IPMI addressing works much like IP addresses, you have an overlay -to handle the different address types. The overlay is: +to handle the different address types. The overlay is:: struct ipmi_addr { @@ -153,7 +152,7 @@ to handle the different address types. The overlay is: The addr_type determines what the address really is. The driver currently understands two different types of addresses. -"System Interface" addresses are defined as: +"System Interface" addresses are defined as:: struct ipmi_system_interface_addr { @@ -166,7 +165,7 @@ straight to the BMC on the current card. The channel must be IPMI_BMC_CHANNEL. Messages that are destined to go out on the IPMB bus use the -IPMI_IPMB_ADDR_TYPE address type. The format is +IPMI_IPMB_ADDR_TYPE address type. The format is:: struct ipmi_ipmb_addr { @@ -184,16 +183,16 @@ spec. Messages -------- -Messages are defined as: +Messages are defined as:: -struct ipmi_msg -{ + struct ipmi_msg + { unsigned char netfn; unsigned char lun; unsigned char cmd; unsigned char *data; int data_len; -}; + }; The driver takes care of adding/stripping the header information. The data portion is just the data to be send (do NOT put addressing info @@ -208,7 +207,7 @@ block of data, even when receiving messages. Otherwise the driver will have no place to put the message. Messages coming up from the message handler in kernelland will come in -as: +as:: struct ipmi_recv_msg { @@ -246,6 +245,7 @@ and the user should not have to care what type of SMI is below them. Watching For Interfaces +^^^^^^^^^^^^^^^^^^^^^^^ When your code comes up, the IPMI driver may or may not have detected if IPMI devices exist. So you might have to defer your setup until @@ -256,6 +256,7 @@ and tell you when they come and go. Creating the User +^^^^^^^^^^^^^^^^^ To use the message handler, you must first create a user using ipmi_create_user. The interface number specifies which SMI you want @@ -272,6 +273,7 @@ closing the device automatically destroys the user. Messaging +^^^^^^^^^ To send a message from kernel-land, the ipmi_request_settime() call does pretty much all message handling. Most of the parameter are @@ -321,6 +323,7 @@ though, since it is tricky to manage your own buffers. Events and Incoming Commands +^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The driver takes care of polling for IPMI events and receiving commands (commands are messages that are not responses, they are @@ -367,7 +370,7 @@ in the system. It discovers interfaces through a host of different methods, depending on the system. You can specify up to four interfaces on the module load line and -control some module parameters: +control some module parameters:: modprobe ipmi_si.o type=<type1>,<type2>.... ports=<port1>,<port2>... addrs=<addr1>,<addr2>... @@ -437,7 +440,7 @@ default is one. Setting to 0 is useful with the hotmod, but is obviously only useful for modules. When compiled into the kernel, the parameters can be specified on the -kernel command line as: +kernel command line as:: ipmi_si.type=<type1>,<type2>... ipmi_si.ports=<port1>,<port2>... ipmi_si.addrs=<addr1>,<addr2>... @@ -474,16 +477,22 @@ The driver supports a hot add and remove of interfaces. This way, interfaces can be added or removed after the kernel is up and running. This is done using /sys/modules/ipmi_si/parameters/hotmod, which is a write-only parameter. You write a string to this interface. The string -has the format: +has the format:: + <op1>[:op2[:op3...]] -The "op"s are: + +The "op"s are:: + add|remove,kcs|bt|smic,mem|i/o,<address>[,<opt1>[,<opt2>[,...]]] -You can specify more than one interface on the line. The "opt"s are: + +You can specify more than one interface on the line. The "opt"s are:: + rsp=<regspacing> rsi=<regsize> rsh=<regshift> irq=<irq> ipmb=<ipmb slave addr> + and these have the same meanings as discussed above. Note that you can also use this on the kernel command line for a more compact format for specifying an interface. Note that when removing an interface, @@ -496,7 +505,7 @@ The SMBus Driver (SSIF) The SMBus driver allows up to 4 SMBus devices to be configured in the system. By default, the driver will only register with something it finds in DMI or ACPI tables. You can change this -at module load time (for a module) with: +at module load time (for a module) with:: modprobe ipmi_ssif.o addr=<i2caddr1>[,<i2caddr2>[,...]] @@ -535,7 +544,7 @@ the smb_addr parameter unless you have DMI or ACPI data to tell the driver what to use. When compiled into the kernel, the addresses can be specified on the -kernel command line as: +kernel command line as:: ipmb_ssif.addr=<i2caddr1>[,<i2caddr2>[...]] ipmi_ssif.adapter=<adapter1>[,<adapter2>[...]] @@ -565,9 +574,9 @@ Some users need more detailed information about a device, like where the address came from or the raw base device for the IPMI interface. You can use the IPMI smi_watcher to catch the IPMI interfaces as they come or go, and to grab the information, you can use the function -ipmi_get_smi_info(), which returns the following structure: +ipmi_get_smi_info(), which returns the following structure:: -struct ipmi_smi_info { + struct ipmi_smi_info { enum ipmi_addr_src addr_src; struct device *dev; union { @@ -575,7 +584,7 @@ struct ipmi_smi_info { void *acpi_handle; } acpi_info; } addr_info; -}; + }; Currently special info for only for SI_ACPI address sources is returned. Others may be added as necessary. @@ -590,7 +599,7 @@ Watchdog A watchdog timer is provided that implements the Linux-standard watchdog timer interface. It has three module parameters that can be -used to control it: +used to control it:: modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type> preaction=<preaction type> preop=<preop type> start_now=x @@ -635,7 +644,7 @@ watchdog device is closed. The default value of nowayout is true if the CONFIG_WATCHDOG_NOWAYOUT option is enabled, or false if not. When compiled into the kernel, the kernel command line is available -for configuring the watchdog: +for configuring the watchdog:: ipmi_watchdog.timeout=<t> ipmi_watchdog.pretimeout=<t> ipmi_watchdog.action=<action type> @@ -675,6 +684,7 @@ also get a bunch of OEM events holding the panic string. The field settings of the events are: + * Generator ID: 0x21 (kernel) * EvM Rev: 0x03 (this event is formatting in IPMI 1.0 format) * Sensor Type: 0x20 (OS critical stop sensor) @@ -683,18 +693,20 @@ The field settings of the events are: * Event Data 1: 0xa1 (Runtime stop in OEM bytes 2 and 3) * Event data 2: second byte of panic string * Event data 3: third byte of panic string + See the IPMI spec for the details of the event layout. This event is always sent to the local management controller. It will handle routing the message to the right place Other OEM events have the following format: -Record ID (bytes 0-1): Set by the SEL. -Record type (byte 2): 0xf0 (OEM non-timestamped) -byte 3: The slave address of the card saving the panic -byte 4: A sequence number (starting at zero) -The rest of the bytes (11 bytes) are the panic string. If the panic string -is longer than 11 bytes, multiple messages will be sent with increasing -sequence numbers. + +* Record ID (bytes 0-1): Set by the SEL. +* Record type (byte 2): 0xf0 (OEM non-timestamped) +* byte 3: The slave address of the card saving the panic +* byte 4: A sequence number (starting at zero) + The rest of the bytes (11 bytes) are the panic string. If the panic string + is longer than 11 bytes, multiple messages will be sent with increasing + sequence numbers. Because you cannot send OEM events using the standard interface, this function will attempt to find an SEL and add the events there. It diff --git a/Documentation/IRQ-affinity.txt b/Documentation/IRQ-affinity.txt index 01a675175a36..29da5000836a 100644 --- a/Documentation/IRQ-affinity.txt +++ b/Documentation/IRQ-affinity.txt @@ -1,8 +1,11 @@ +================ +SMP IRQ affinity +================ + ChangeLog: - Started by Ingo Molnar <mingo@redhat.com> - Update by Max Krasnyansky <maxk@qualcomm.com> + - Started by Ingo Molnar <mingo@redhat.com> + - Update by Max Krasnyansky <maxk@qualcomm.com> -SMP IRQ affinity /proc/irq/IRQ#/smp_affinity and /proc/irq/IRQ#/smp_affinity_list specify which target CPUs are permitted for a given IRQ source. It's a bitmask @@ -16,50 +19,52 @@ will be set to the default mask. It can then be changed as described above. Default mask is 0xffffffff. Here is an example of restricting IRQ44 (eth1) to CPU0-3 then restricting -it to CPU4-7 (this is an 8-CPU SMP box): +it to CPU4-7 (this is an 8-CPU SMP box):: -[root@moon 44]# cd /proc/irq/44 -[root@moon 44]# cat smp_affinity -ffffffff + [root@moon 44]# cd /proc/irq/44 + [root@moon 44]# cat smp_affinity + ffffffff -[root@moon 44]# echo 0f > smp_affinity -[root@moon 44]# cat smp_affinity -0000000f -[root@moon 44]# ping -f h -PING hell (195.4.7.3): 56 data bytes -... ---- hell ping statistics --- -6029 packets transmitted, 6027 packets received, 0% packet loss -round-trip min/avg/max = 0.1/0.1/0.4 ms -[root@moon 44]# cat /proc/interrupts | grep 'CPU\|44:' - CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 - 44: 1068 1785 1785 1783 0 0 0 0 IO-APIC-level eth1 + [root@moon 44]# echo 0f > smp_affinity + [root@moon 44]# cat smp_affinity + 0000000f + [root@moon 44]# ping -f h + PING hell (195.4.7.3): 56 data bytes + ... + --- hell ping statistics --- + 6029 packets transmitted, 6027 packets received, 0% packet loss + round-trip min/avg/max = 0.1/0.1/0.4 ms + [root@moon 44]# cat /proc/interrupts | grep 'CPU\|44:' + CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 + 44: 1068 1785 1785 1783 0 0 0 0 IO-APIC-level eth1 As can be seen from the line above IRQ44 was delivered only to the first four processors (0-3). Now lets restrict that IRQ to CPU(4-7). -[root@moon 44]# echo f0 > smp_affinity -[root@moon 44]# cat smp_affinity -000000f0 -[root@moon 44]# ping -f h -PING hell (195.4.7.3): 56 data bytes -.. ---- hell ping statistics --- -2779 packets transmitted, 2777 packets received, 0% packet loss -round-trip min/avg/max = 0.1/0.5/585.4 ms -[root@moon 44]# cat /proc/interrupts | 'CPU\|44:' - CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 - 44: 1068 1785 1785 1783 1784 1069 1070 1069 IO-APIC-level eth1 +:: + + [root@moon 44]# echo f0 > smp_affinity + [root@moon 44]# cat smp_affinity + 000000f0 + [root@moon 44]# ping -f h + PING hell (195.4.7.3): 56 data bytes + .. + --- hell ping statistics --- + 2779 packets transmitted, 2777 packets received, 0% packet loss + round-trip min/avg/max = 0.1/0.5/585.4 ms + [root@moon 44]# cat /proc/interrupts | 'CPU\|44:' + CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 + 44: 1068 1785 1785 1783 1784 1069 1070 1069 IO-APIC-level eth1 This time around IRQ44 was delivered only to the last four processors. i.e counters for the CPU0-3 did not change. -Here is an example of limiting that same irq (44) to cpus 1024 to 1031: +Here is an example of limiting that same irq (44) to cpus 1024 to 1031:: -[root@moon 44]# echo 1024-1031 > smp_affinity_list -[root@moon 44]# cat smp_affinity_list -1024-1031 + [root@moon 44]# echo 1024-1031 > smp_affinity_list + [root@moon 44]# cat smp_affinity_list + 1024-1031 Note that to do this with a bitmask would require 32 bitmasks of zero to follow the pertinent one. diff --git a/Documentation/IRQ-domain.txt b/Documentation/IRQ-domain.txt index 1f246eb25ca5..4a1cd7645d85 100644 --- a/Documentation/IRQ-domain.txt +++ b/Documentation/IRQ-domain.txt @@ -1,4 +1,6 @@ -irq_domain interrupt number mapping library +=============================================== +The irq_domain interrupt number mapping library +=============================================== The current design of the Linux kernel uses a single large number space where each separate IRQ source is assigned a different number. @@ -36,7 +38,9 @@ irq_domain also implements translation from an abstract irq_fwspec structure to hwirq numbers (Device Tree and ACPI GSI so far), and can be easily extended to support other IRQ topology data sources. -=== irq_domain usage === +irq_domain usage +================ + An interrupt controller driver creates and registers an irq_domain by calling one of the irq_domain_add_*() functions (each mapping method has a different allocator function, more on that later). The function @@ -62,15 +66,21 @@ If the driver has the Linux IRQ number or the irq_data pointer, and needs to know the associated hwirq number (such as in the irq_chip callbacks) then it can be directly obtained from irq_data->hwirq. -=== Types of irq_domain mappings === +Types of irq_domain mappings +============================ + There are several mechanisms available for reverse mapping from hwirq to Linux irq, and each mechanism uses a different allocation function. Which reverse map type should be used depends on the use case. Each of the reverse map types are described below: -==== Linear ==== -irq_domain_add_linear() -irq_domain_create_linear() +Linear +------ + +:: + + irq_domain_add_linear() + irq_domain_create_linear() The linear reverse map maintains a fixed size table indexed by the hwirq number. When a hwirq is mapped, an irq_desc is allocated for @@ -89,9 +99,13 @@ accepts a more general abstraction 'struct fwnode_handle'. The majority of drivers should use the linear map. -==== Tree ==== -irq_domain_add_tree() -irq_domain_create_tree() +Tree +---- + +:: + + irq_domain_add_tree() + irq_domain_create_tree() The irq_domain maintains a radix tree map from hwirq numbers to Linux IRQs. When an hwirq is mapped, an irq_desc is allocated and the @@ -109,8 +123,12 @@ accepts a more general abstraction 'struct fwnode_handle'. Very few drivers should need this mapping. -==== No Map ===- -irq_domain_add_nomap() +No Map +------ + +:: + + irq_domain_add_nomap() The No Map mapping is to be used when the hwirq number is programmable in the hardware. In this case it is best to program the @@ -121,10 +139,14 @@ Linux IRQ number into the hardware. Most drivers cannot use this mapping. -==== Legacy ==== -irq_domain_add_simple() -irq_domain_add_legacy() -irq_domain_add_legacy_isa() +Legacy +------ + +:: + + irq_domain_add_simple() + irq_domain_add_legacy() + irq_domain_add_legacy_isa() The Legacy mapping is a special case for drivers that already have a range of irq_descs allocated for the hwirqs. It is used when the @@ -163,14 +185,17 @@ that the driver using the simple domain call irq_create_mapping() before any irq_find_mapping() since the latter will actually work for the static IRQ assignment case. -==== Hierarchy IRQ domain ==== +Hierarchy IRQ domain +-------------------- + On some architectures, there may be multiple interrupt controllers involved in delivering an interrupt from the device to the target CPU. -Let's look at a typical interrupt delivering path on x86 platforms: +Let's look at a typical interrupt delivering path on x86 platforms:: -Device --> IOAPIC -> Interrupt remapping Controller -> Local APIC -> CPU + Device --> IOAPIC -> Interrupt remapping Controller -> Local APIC -> CPU There are three interrupt controllers involved: + 1) IOAPIC controller 2) Interrupt remapping controller 3) Local APIC controller @@ -180,7 +205,8 @@ hardware architecture, an irq_domain data structure is built for each interrupt controller and those irq_domains are organized into hierarchy. When building irq_domain hierarchy, the irq_domain near to the device is child and the irq_domain near to CPU is parent. So a hierarchy structure -as below will be built for the example above. +as below will be built for the example above:: + CPU Vector irq_domain (root irq_domain to manage CPU vectors) ^ | @@ -190,6 +216,7 @@ as below will be built for the example above. IOAPIC irq_domain (manage IOAPIC delivery entries/pins) There are four major interfaces to use hierarchy irq_domain: + 1) irq_domain_alloc_irqs(): allocate IRQ descriptors and interrupt controller related resources to deliver these interrupts. 2) irq_domain_free_irqs(): free IRQ descriptors and interrupt controller @@ -199,7 +226,8 @@ There are four major interfaces to use hierarchy irq_domain: 4) irq_domain_deactivate_irq(): deactivate interrupt controller hardware to stop delivering the interrupt. -Following changes are needed to support hierarchy irq_domain. +Following changes are needed to support hierarchy irq_domain: + 1) a new field 'parent' is added to struct irq_domain; it's used to maintain irq_domain hierarchy information. 2) a new field 'parent_data' is added to struct irq_data; it's used to @@ -223,6 +251,7 @@ software architecture. For an interrupt controller driver to support hierarchy irq_domain, it needs to: + 1) Implement irq_domain_ops.alloc and irq_domain_ops.free 2) Optionally implement irq_domain_ops.activate and irq_domain_ops.deactivate. diff --git a/Documentation/IRQ.txt b/Documentation/IRQ.txt index 1011e7175021..4273806a606b 100644 --- a/Documentation/IRQ.txt +++ b/Documentation/IRQ.txt @@ -1,4 +1,6 @@ +=============== What is an IRQ? +=============== An IRQ is an interrupt request from a device. Currently they can come in over a pin, or over a packet. diff --git a/Documentation/Intel-IOMMU.txt b/Documentation/Intel-IOMMU.txt index 49585b6e1ea2..9dae6b47e398 100644 --- a/Documentation/Intel-IOMMU.txt +++ b/Documentation/Intel-IOMMU.txt @@ -1,3 +1,4 @@ +=================== Linux IOMMU Support =================== @@ -9,11 +10,11 @@ This guide gives a quick cheat sheet for some basic understanding. Some Keywords -DMAR - DMA remapping -DRHD - DMA Remapping Hardware Unit Definition -RMRR - Reserved memory Region Reporting Structure -ZLR - Zero length reads from PCI devices -IOVA - IO Virtual address. +- DMAR - DMA remapping +- DRHD - DMA Remapping Hardware Unit Definition +- RMRR - Reserved memory Region Reporting Structure +- ZLR - Zero length reads from PCI devices +- IOVA - IO Virtual address. Basic stuff ----------- @@ -33,7 +34,7 @@ devices that need to access these regions. OS is expected to setup unity mappings for these regions for these devices to access these regions. How is IOVA generated? ---------------------- +---------------------- Well behaved drivers call pci_map_*() calls before sending command to device that needs to perform DMA. Once DMA is completed and mapping is no longer @@ -82,14 +83,14 @@ in ACPI. ACPI: DMAR (v001 A M I OEMDMAR 0x00000001 MSFT 0x00000097) @ 0x000000007f5b5ef0 When DMAR is being processed and initialized by ACPI, prints DMAR locations -and any RMRR's processed. +and any RMRR's processed:: -ACPI DMAR:Host address width 36 -ACPI DMAR:DRHD (flags: 0x00000000)base: 0x00000000fed90000 -ACPI DMAR:DRHD (flags: 0x00000000)base: 0x00000000fed91000 -ACPI DMAR:DRHD (flags: 0x00000001)base: 0x00000000fed93000 -ACPI DMAR:RMRR base: 0x00000000000ed000 end: 0x00000000000effff -ACPI DMAR:RMRR base: 0x000000007f600000 end: 0x000000007fffffff + ACPI DMAR:Host address width 36 + ACPI DMAR:DRHD (flags: 0x00000000)base: 0x00000000fed90000 + ACPI DMAR:DRHD (flags: 0x00000000)base: 0x00000000fed91000 + ACPI DMAR:DRHD (flags: 0x00000001)base: 0x00000000fed93000 + ACPI DMAR:RMRR base: 0x00000000000ed000 end: 0x00000000000effff + ACPI DMAR:RMRR base: 0x000000007f600000 end: 0x000000007fffffff When DMAR is enabled for use, you will notice.. @@ -98,10 +99,12 @@ PCI-DMA: Using DMAR IOMMU Fault reporting --------------- -DMAR:[DMA Write] Request device [00:02.0] fault addr 6df084000 -DMAR:[fault reason 05] PTE Write access is not set -DMAR:[DMA Write] Request device [00:02.0] fault addr 6df084000 -DMAR:[fault reason 05] PTE Write access is not set +:: + + DMAR:[DMA Write] Request device [00:02.0] fault addr 6df084000 + DMAR:[fault reason 05] PTE Write access is not set + DMAR:[DMA Write] Request device [00:02.0] fault addr 6df084000 + DMAR:[fault reason 05] PTE Write access is not set TBD ---- diff --git a/Documentation/SAK.txt b/Documentation/SAK.txt index 74be14679ed8..260e1d3687bd 100644 --- a/Documentation/SAK.txt +++ b/Documentation/SAK.txt @@ -1,5 +1,9 @@ -Linux 2.4.2 Secure Attention Key (SAK) handling -18 March 2001, Andrew Morton +========================================= +Linux Secure Attention Key (SAK) handling +========================================= + +:Date: 18 March 2001 +:Author: Andrew Morton An operating system's Secure Attention Key is a security tool which is provided as protection against trojan password capturing programs. It @@ -13,7 +17,7 @@ this sequence. It is only available if the kernel was compiled with sysrq support. The proper way of generating a SAK is to define the key sequence using -`loadkeys'. This will work whether or not sysrq support is compiled +``loadkeys``. This will work whether or not sysrq support is compiled into the kernel. SAK works correctly when the keyboard is in raw mode. This means that @@ -25,64 +29,63 @@ What key sequence should you use? Well, CTRL-ALT-DEL is used to reboot the machine. CTRL-ALT-BACKSPACE is magical to the X server. We'll choose CTRL-ALT-PAUSE. -In your rc.sysinit (or rc.local) file, add the command +In your rc.sysinit (or rc.local) file, add the command:: echo "control alt keycode 101 = SAK" | /bin/loadkeys And that's it! Only the superuser may reprogram the SAK key. -NOTES -===== +.. note:: -1: Linux SAK is said to be not a "true SAK" as is required by - systems which implement C2 level security. This author does not - know why. + 1. Linux SAK is said to be not a "true SAK" as is required by + systems which implement C2 level security. This author does not + know why. -2: On the PC keyboard, SAK kills all applications which have - /dev/console opened. + 2. On the PC keyboard, SAK kills all applications which have + /dev/console opened. - Unfortunately this includes a number of things which you don't - actually want killed. This is because these applications are - incorrectly holding /dev/console open. Be sure to complain to your - Linux distributor about this! + Unfortunately this includes a number of things which you don't + actually want killed. This is because these applications are + incorrectly holding /dev/console open. Be sure to complain to your + Linux distributor about this! - You can identify processes which will be killed by SAK with the - command + You can identify processes which will be killed by SAK with the + command:: # ls -l /proc/[0-9]*/fd/* | grep console l-wx------ 1 root root 64 Mar 18 00:46 /proc/579/fd/0 -> /dev/console - Then: + Then:: # ps aux|grep 579 root 579 0.0 0.1 1088 436 ? S 00:43 0:00 gpm -t ps/2 - So `gpm' will be killed by SAK. This is a bug in gpm. It should - be closing standard input. You can work around this by finding the - initscript which launches gpm and changing it thusly: + So ``gpm`` will be killed by SAK. This is a bug in gpm. It should + be closing standard input. You can work around this by finding the + initscript which launches gpm and changing it thusly: - Old: + Old:: daemon gpm - New: + New:: daemon gpm < /dev/null - Vixie cron also seems to have this problem, and needs the same treatment. + Vixie cron also seems to have this problem, and needs the same treatment. - Also, one prominent Linux distribution has the following three - lines in its rc.sysinit and rc scripts: + Also, one prominent Linux distribution has the following three + lines in its rc.sysinit and rc scripts:: exec 3<&0 exec 4>&1 exec 5>&2 - These commands cause *all* daemons which are launched by the - initscripts to have file descriptors 3, 4 and 5 attached to - /dev/console. So SAK kills them all. A workaround is to simply - delete these lines, but this may cause system management - applications to malfunction - test everything well. + These commands cause **all** daemons which are launched by the + initscripts to have file descriptors 3, 4 and 5 attached to + /dev/console. So SAK kills them all. A workaround is to simply + delete these lines, but this may cause system management + applications to malfunction - test everything well. diff --git a/Documentation/SM501.txt b/Documentation/SM501.txt index 561826f82093..882507453ba4 100644 --- a/Documentation/SM501.txt +++ b/Documentation/SM501.txt @@ -1,7 +1,10 @@ - SM501 Driver - ============ +.. include:: <isonum.txt> -Copyright 2006, 2007 Simtec Electronics +============ +SM501 Driver +============ + +:Copyright: |copy| 2006, 2007 Simtec Electronics The Silicon Motion SM501 multimedia companion chip is a multifunction device which may provide numerous interfaces including USB host controller USB gadget, diff --git a/Documentation/arm64/silicon-errata.txt b/Documentation/arm64/silicon-errata.txt index f5f93dca54b7..66e8ce14d23d 100644 --- a/Documentation/arm64/silicon-errata.txt +++ b/Documentation/arm64/silicon-errata.txt @@ -61,12 +61,15 @@ stable kernels. | Cavium | ThunderX ITS | #23144 | CAVIUM_ERRATUM_23144 | | Cavium | ThunderX GICv3 | #23154 | CAVIUM_ERRATUM_23154 | | Cavium | ThunderX Core | #27456 | CAVIUM_ERRATUM_27456 | -| Cavium | ThunderX SMMUv2 | #27704 | N/A | | Cavium | ThunderX Core | #30115 | CAVIUM_ERRATUM_30115 | +| Cavium | ThunderX SMMUv2 | #27704 | N/A | +| Cavium | ThunderX2 SMMUv3| #74 | N/A | +| Cavium | ThunderX2 SMMUv3| #126 | N/A | | | | | | | Freescale/NXP | LS2080A/LS1043A | A-008585 | FSL_ERRATUM_A008585 | | | | | | | Hisilicon | Hip0{5,6,7} | #161010101 | HISILICON_ERRATUM_161010101 | +| Hisilicon | Hip0{6,7} | #161010701 | N/A | | | | | | | Qualcomm Tech. | Falkor v1 | E1003 | QCOM_FALKOR_ERRATUM_1003 | | Qualcomm Tech. | Falkor v1 | E1009 | QCOM_FALKOR_ERRATUM_1009 | diff --git a/Documentation/bcache.txt b/Documentation/bcache.txt index a9259b562d5c..c0ce64d75bbf 100644 --- a/Documentation/bcache.txt +++ b/Documentation/bcache.txt @@ -1,10 +1,15 @@ +============================ +A block layer cache (bcache) +============================ + Say you've got a big slow raid 6, and an ssd or three. Wouldn't it be nice if you could use them as cache... Hence bcache. Wiki and git repositories are at: - http://bcache.evilpiepirate.org - http://evilpiepirate.org/git/linux-bcache.git - http://evilpiepirate.org/git/bcache-tools.git + + - http://bcache.evilpiepirate.org + - http://evilpiepirate.org/git/linux-bcache.git + - http://evilpiepirate.org/git/bcache-tools.git It's designed around the performance characteristics of SSDs - it only allocates in erase block sized buckets, and it uses a hybrid btree/log to track cached @@ -37,17 +42,19 @@ to be flushed. Getting started: You'll need make-bcache from the bcache-tools repository. Both the cache device -and backing device must be formatted before use. +and backing device must be formatted before use:: + make-bcache -B /dev/sdb make-bcache -C /dev/sdc make-bcache has the ability to format multiple devices at the same time - if you format your backing devices and cache device at the same time, you won't -have to manually attach: +have to manually attach:: + make-bcache -B /dev/sda /dev/sdb -C /dev/sdc bcache-tools now ships udev rules, and bcache devices are known to the kernel -immediately. Without udev, you can manually register devices like this: +immediately. Without udev, you can manually register devices like this:: echo /dev/sdb > /sys/fs/bcache/register echo /dev/sdc > /sys/fs/bcache/register @@ -60,16 +67,16 @@ slow devices as bcache backing devices without a cache, and you can choose to ad a caching device later. See 'ATTACHING' section below. -The devices show up as: +The devices show up as:: /dev/bcache<N> -As well as (with udev): +As well as (with udev):: /dev/bcache/by-uuid/<uuid> /dev/bcache/by-label/<label> -To get started: +To get started:: mkfs.ext4 /dev/bcache0 mount /dev/bcache0 /mnt @@ -81,13 +88,13 @@ Cache devices are managed as sets; multiple caches per set isn't supported yet but will allow for mirroring of metadata and dirty data in the future. Your new cache set shows up as /sys/fs/bcache/<UUID> -ATTACHING +Attaching --------- After your cache device and backing device are registered, the backing device must be attached to your cache set to enable caching. Attaching a backing device to a cache set is done thusly, with the UUID of the cache set in -/sys/fs/bcache: +/sys/fs/bcache:: echo <CSET-UUID> > /sys/block/bcache0/bcache/attach @@ -97,7 +104,7 @@ your bcache devices. If a backing device has data in a cache somewhere, the important if you have writeback caching turned on. If you're booting up and your cache device is gone and never coming back, you -can force run the backing device: +can force run the backing device:: echo 1 > /sys/block/sdb/bcache/running @@ -110,7 +117,7 @@ but all the cached data will be invalidated. If there was dirty data in the cache, don't expect the filesystem to be recoverable - you will have massive filesystem corruption, though ext4's fsck does work miracles. -ERROR HANDLING +Error Handling -------------- Bcache tries to transparently handle IO errors to/from the cache device without @@ -134,25 +141,27 @@ the backing devices to passthrough mode. read some of the dirty data, though. -HOWTO/COOKBOOK +Howto/cookbook -------------- A) Starting a bcache with a missing caching device If registering the backing device doesn't help, it's already there, you just need -to force it to run without the cache: +to force it to run without the cache:: + host:~# echo /dev/sdb1 > /sys/fs/bcache/register [ 119.844831] bcache: register_bcache() error opening /dev/sdb1: device already registered Next, you try to register your caching device if it's present. However if it's absent, or registration fails for some reason, you can still -start your bcache without its cache, like so: +start your bcache without its cache, like so:: + host:/sys/block/sdb/sdb1/bcache# echo 1 > running Note that this may cause data loss if you were running in writeback mode. -B) Bcache does not find its cache +B) Bcache does not find its cache:: host:/sys/block/md5/bcache# echo 0226553a-37cf-41d5-b3ce-8b1e944543a8 > attach [ 1933.455082] bcache: bch_cached_dev_attach() Couldn't find uuid for md5 in set @@ -160,7 +169,8 @@ B) Bcache does not find its cache [ 1933.478179] : cache set not found In this case, the caching device was simply not registered at boot -or disappeared and came back, and needs to be (re-)registered: +or disappeared and came back, and needs to be (re-)registered:: + host:/sys/block/md5/bcache# echo /dev/sdh2 > /sys/fs/bcache/register @@ -180,7 +190,8 @@ device is still available at an 8KiB offset. So either via a loopdev of the backing device created with --offset 8K, or any value defined by --data-offset when you originally formatted bcache with `make-bcache`. -For example: +For example:: + losetup -o 8192 /dev/loop0 /dev/your_bcache_backing_dev This should present your unmodified backing device data in /dev/loop0 @@ -191,33 +202,38 @@ cache device without loosing data. E) Wiping a cache device -host:~# wipefs -a /dev/sdh2 -16 bytes were erased at offset 0x1018 (bcache) -they were: c6 85 73 f6 4e 1a 45 ca 82 65 f5 7f 48 ba 6d 81 +:: + + host:~# wipefs -a /dev/sdh2 + 16 bytes were erased at offset 0x1018 (bcache) + they were: c6 85 73 f6 4e 1a 45 ca 82 65 f5 7f 48 ba 6d 81 + +After you boot back with bcache enabled, you recreate the cache and attach it:: -After you boot back with bcache enabled, you recreate the cache and attach it: -host:~# make-bcache -C /dev/sdh2 -UUID: 7be7e175-8f4c-4f99-94b2-9c904d227045 -Set UUID: 5bc072a8-ab17-446d-9744-e247949913c1 -version: 0 -nbuckets: 106874 -block_size: 1 -bucket_size: 1024 -nr_in_set: 1 -nr_this_dev: 0 -first_bucket: 1 -[ 650.511912] bcache: run_cache_set() invalidating existing data -[ 650.549228] bcache: register_cache() registered cache device sdh2 + host:~# make-bcache -C /dev/sdh2 + UUID: 7be7e175-8f4c-4f99-94b2-9c904d227045 + Set UUID: 5bc072a8-ab17-446d-9744-e247949913c1 + version: 0 + nbuckets: 106874 + block_size: 1 + bucket_size: 1024 + nr_in_set: 1 + nr_this_dev: 0 + first_bucket: 1 + [ 650.511912] bcache: run_cache_set() invalidating existing data + [ 650.549228] bcache: register_cache() registered cache device sdh2 -start backing device with missing cache: -host:/sys/block/md5/bcache# echo 1 > running +start backing device with missing cache:: -attach new cache: -host:/sys/block/md5/bcache# echo 5bc072a8-ab17-446d-9744-e247949913c1 > attach -[ 865.276616] bcache: bch_cached_dev_attach() Caching md5 as bcache0 on set 5bc072a8-ab17-446d-9744-e247949913c1 + host:/sys/block/md5/bcache# echo 1 > running +attach new cache:: -F) Remove or replace a caching device + host:/sys/block/md5/bcache# echo 5bc072a8-ab17-446d-9744-e247949913c1 > attach + [ 865.276616] bcache: bch_cached_dev_attach() Caching md5 as bcache0 on set 5bc072a8-ab17-446d-9744-e247949913c1 + + +F) Remove or replace a caching device:: host:/sys/block/sda/sda7/bcache# echo 1 > detach [ 695.872542] bcache: cached_dev_detach_finish() Caching disabled for sda7 @@ -226,13 +242,15 @@ F) Remove or replace a caching device wipefs: error: /dev/nvme0n1p4: probing initialization failed: Device or resource busy Ooops, it's disabled, but not unregistered, so it's still protected -We need to go and unregister it: +We need to go and unregister it:: + host:/sys/fs/bcache/b7ba27a1-2398-4649-8ae3-0959f57ba128# ls -l cache0 lrwxrwxrwx 1 root root 0 Feb 25 18:33 cache0 -> ../../../devices/pci0000:00/0000:00:1d.0/0000:70:00.0/nvme/nvme0/nvme0n1/nvme0n1p4/bcache/ host:/sys/fs/bcache/b7ba27a1-2398-4649-8ae3-0959f57ba128# echo 1 > stop kernel: [ 917.041908] bcache: cache_set_free() Cache set b7ba27a1-2398-4649-8ae3-0959f57ba128 unregistered -Now we can wipe it: +Now we can wipe it:: + host:~# wipefs -a /dev/nvme0n1p4 /dev/nvme0n1p4: 16 bytes were erased at offset 0x00001018 (bcache): c6 85 73 f6 4e 1a 45 ca 82 65 f5 7f 48 ba 6d 81 @@ -252,40 +270,44 @@ if there are any active backing or caching devices left on it: 1) Is it present in /dev/bcache* ? (there are times where it won't be) -If so, it's easy: + If so, it's easy:: + host:/sys/block/bcache0/bcache# echo 1 > stop -2) But if your backing device is gone, this won't work: +2) But if your backing device is gone, this won't work:: + host:/sys/block/bcache0# cd bcache bash: cd: bcache: No such file or directory -In this case, you may have to unregister the dmcrypt block device that -references this bcache to free it up: + In this case, you may have to unregister the dmcrypt block device that + references this bcache to free it up:: + host:~# dmsetup remove oldds1 bcache: bcache_device_free() bcache0 stopped bcache: cache_set_free() Cache set 5bc072a8-ab17-446d-9744-e247949913c1 unregistered -This causes the backing bcache to be removed from /sys/fs/bcache and -then it can be reused. This would be true of any block device stacking -where bcache is a lower device. + This causes the backing bcache to be removed from /sys/fs/bcache and + then it can be reused. This would be true of any block device stacking + where bcache is a lower device. + +3) In other cases, you can also look in /sys/fs/bcache/:: -3) In other cases, you can also look in /sys/fs/bcache/: + host:/sys/fs/bcache# ls -l */{cache?,bdev?} + lrwxrwxrwx 1 root root 0 Mar 5 09:39 0226553a-37cf-41d5-b3ce-8b1e944543a8/bdev1 -> ../../../devices/virtual/block/dm-1/bcache/ + lrwxrwxrwx 1 root root 0 Mar 5 09:39 0226553a-37cf-41d5-b3ce-8b1e944543a8/cache0 -> ../../../devices/virtual/block/dm-4/bcache/ + lrwxrwxrwx 1 root root 0 Mar 5 09:39 5bc072a8-ab17-446d-9744-e247949913c1/cache0 -> ../../../devices/pci0000:00/0000:00:01.0/0000:01:00.0/ata10/host9/target9:0:0/9:0:0:0/block/sdl/sdl2/bcache/ -host:/sys/fs/bcache# ls -l */{cache?,bdev?} -lrwxrwxrwx 1 root root 0 Mar 5 09:39 0226553a-37cf-41d5-b3ce-8b1e944543a8/bdev1 -> ../../../devices/virtual/block/dm-1/bcache/ -lrwxrwxrwx 1 root root 0 Mar 5 09:39 0226553a-37cf-41d5-b3ce-8b1e944543a8/cache0 -> ../../../devices/virtual/block/dm-4/bcache/ -lrwxrwxrwx 1 root root 0 Mar 5 09:39 5bc072a8-ab17-446d-9744-e247949913c1/cache0 -> ../../../devices/pci0000:00/0000:00:01.0/0000:01:00.0/ata10/host9/target9:0:0/9:0:0:0/block/sdl/sdl2/bcache/ + The device names will show which UUID is relevant, cd in that directory + and stop the cache:: -The device names will show which UUID is relevant, cd in that directory -and stop the cache: host:/sys/fs/bcache/5bc072a8-ab17-446d-9744-e247949913c1# echo 1 > stop -This will free up bcache references and let you reuse the partition for -other purposes. + This will free up bcache references and let you reuse the partition for + other purposes. -TROUBLESHOOTING PERFORMANCE +Troubleshooting performance --------------------------- Bcache has a bunch of config options and tunables. The defaults are intended to @@ -301,11 +323,13 @@ want for getting the best possible numbers when benchmarking. raid stripe size to get the disk multiples that you would like. For example: If you have a 64k stripe size, then the following offset - would provide alignment for many common RAID5 data spindle counts: + would provide alignment for many common RAID5 data spindle counts:: + 64k * 2*2*2*3*3*5*7 bytes = 161280k That space is wasted, but for only 157.5MB you can grow your RAID 5 - volume to the following data-spindle counts without re-aligning: + volume to the following data-spindle counts without re-aligning:: + 3,4,5,6,7,8,9,10,12,14,15,18,20,21 ... - Bad write performance @@ -313,9 +337,9 @@ want for getting the best possible numbers when benchmarking. If write performance is not what you expected, you probably wanted to be running in writeback mode, which isn't the default (not due to a lack of maturity, but simply because in writeback mode you'll lose data if something - happens to your SSD) + happens to your SSD):: - # echo writeback > /sys/block/bcache0/bcache/cache_mode + # echo writeback > /sys/block/bcache0/bcache/cache_mode - Bad performance, or traffic not going to the SSD that you'd expect @@ -325,13 +349,13 @@ want for getting the best possible numbers when benchmarking. accessed data out of your cache. But if you want to benchmark reads from cache, and you start out with fio - writing an 8 gigabyte test file - so you want to disable that. + writing an 8 gigabyte test file - so you want to disable that:: - # echo 0 > /sys/block/bcache0/bcache/sequential_cutoff + # echo 0 > /sys/block/bcache0/bcache/sequential_cutoff - To set it back to the default (4 mb), do + To set it back to the default (4 mb), do:: - # echo 4M > /sys/block/bcache0/bcache/sequential_cutoff + # echo 4M > /sys/block/bcache0/bcache/sequential_cutoff - Traffic's still going to the spindle/still getting cache misses @@ -344,10 +368,10 @@ want for getting the best possible numbers when benchmarking. throttles traffic if the latency exceeds a threshold (it does this by cranking down the sequential bypass). - You can disable this if you need to by setting the thresholds to 0: + You can disable this if you need to by setting the thresholds to 0:: - # echo 0 > /sys/fs/bcache/<cache set>/congested_read_threshold_us - # echo 0 > /sys/fs/bcache/<cache set>/congested_write_threshold_us + # echo 0 > /sys/fs/bcache/<cache set>/congested_read_threshold_us + # echo 0 > /sys/fs/bcache/<cache set>/congested_write_threshold_us The default is 2000 us (2 milliseconds) for reads, and 20000 for writes. @@ -369,7 +393,7 @@ want for getting the best possible numbers when benchmarking. a fix for the issue there). -SYSFS - BACKING DEVICE +Sysfs - backing device ---------------------- Available at /sys/block/<bdev>/bcache, /sys/block/bcache*/bcache and @@ -454,7 +478,8 @@ writeback_running still be added to the cache until it is mostly full; only meant for benchmarking. Defaults to on. -SYSFS - BACKING DEVICE STATS: +Sysfs - backing device stats +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ There are directories with these numbers for a running total, as well as versions that decay over the past day, hour and 5 minutes; they're also @@ -463,14 +488,11 @@ aggregated in the cache set directory as well. bypassed Amount of IO (both reads and writes) that has bypassed the cache -cache_hits -cache_misses -cache_hit_ratio +cache_hits, cache_misses, cache_hit_ratio Hits and misses are counted per individual IO as bcache sees them; a partial hit is counted as a miss. -cache_bypass_hits -cache_bypass_misses +cache_bypass_hits, cache_bypass_misses Hits and misses for IO that is intended to skip the cache are still counted, but broken out here. @@ -482,7 +504,8 @@ cache_miss_collisions cache_readaheads Count of times readahead occurred. -SYSFS - CACHE SET: +Sysfs - cache set +~~~~~~~~~~~~~~~~~ Available at /sys/fs/bcache/<cset-uuid> @@ -520,8 +543,7 @@ flash_vol_create Echoing a size to this file (in human readable units, k/M/G) creates a thinly provisioned volume backed by the cache set. -io_error_halflife -io_error_limit +io_error_halflife, io_error_limit These determines how many errors we accept before disabling the cache. Each error is decayed by the half life (in # ios). If the decaying count reaches io_error_limit dirty data is written out and the cache is disabled. @@ -545,7 +567,8 @@ unregister Detaches all backing devices and closes the cache devices; if dirty data is present it will disable writeback caching and wait for it to be flushed. -SYSFS - CACHE SET INTERNAL: +Sysfs - cache set internal +~~~~~~~~~~~~~~~~~~~~~~~~~~ This directory also exposes timings for a number of internal operations, with separate files for average duration, average frequency, last occurrence and max @@ -574,7 +597,8 @@ cache_read_races trigger_gc Writing to this file forces garbage collection to run. -SYSFS - CACHE DEVICE: +Sysfs - Cache device +~~~~~~~~~~~~~~~~~~~~ Available at /sys/block/<cdev>/bcache diff --git a/Documentation/block/data-integrity.txt b/Documentation/block/data-integrity.txt index f56ec97f0d14..934c44ea0c57 100644 --- a/Documentation/block/data-integrity.txt +++ b/Documentation/block/data-integrity.txt @@ -192,7 +192,7 @@ will require extra work due to the application tag. supported by the block device. - int bio_integrity_prep(bio); + bool bio_integrity_prep(bio); To generate IMD for WRITE and to set up buffers for READ, the filesystem must call bio_integrity_prep(bio). @@ -201,9 +201,7 @@ will require extra work due to the application tag. sector must be set, and the bio should have all data pages added. It is up to the caller to ensure that the bio does not change while I/O is in progress. - - bio_integrity_prep() should only be called if - bio_integrity_enabled() returned 1. + Complete bio with error if prepare failed for some reson. 5.3 PASSING EXISTING INTEGRITY METADATA diff --git a/Documentation/bt8xxgpio.txt b/Documentation/bt8xxgpio.txt index d8297e4ebd26..a845feb074de 100644 --- a/Documentation/bt8xxgpio.txt +++ b/Documentation/bt8xxgpio.txt @@ -1,12 +1,8 @@ -=============================================================== -== BT8XXGPIO driver == -== == -== A driver for a selfmade cheap BT8xx based PCI GPIO-card == -== == -== For advanced documentation, see == -== http://www.bu3sch.de/btgpio.php == -=============================================================== +=================================================================== +A driver for a selfmade cheap BT8xx based PCI GPIO-card (bt8xxgpio) +=================================================================== +For advanced documentation, see http://www.bu3sch.de/btgpio.php A generic digital 24-port PCI GPIO card can be built out of an ordinary Brooktree bt848, bt849, bt878 or bt879 based analog TV tuner card. The @@ -17,9 +13,8 @@ The bt8xx chip does have 24 digital GPIO ports. These ports are accessible via 24 pins on the SMD chip package. -============================================== -== How to physically access the GPIO pins == -============================================== +How to physically access the GPIO pins +====================================== The are several ways to access these pins. One might unsolder the whole chip and put it on a custom PCI board, or one might only unsolder each individual @@ -27,7 +22,7 @@ GPIO pin and solder that to some tiny wire. As the chip package really is tiny there are some advanced soldering skills needed in any case. The physical pinouts are drawn in the following ASCII art. -The GPIO pins are marked with G00-G23 +The GPIO pins are marked with G00-G23:: G G G G G G G G G G G G G G G G G G 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 diff --git a/Documentation/btmrvl.txt b/Documentation/btmrvl.txt index 34916a46c099..ec57740ead0c 100644 --- a/Documentation/btmrvl.txt +++ b/Documentation/btmrvl.txt @@ -1,18 +1,16 @@ -======================================================================= - README for btmrvl driver -======================================================================= - +============= +btmrvl driver +============= All commands are used via debugfs interface. -===================== -Set/get driver configurations: +Set/get driver configurations +============================= Path: /debug/btmrvl/config/ -gpiogap=[n] -hscfgcmd - These commands are used to configure the host sleep parameters. +gpiogap=[n], hscfgcmd + These commands are used to configure the host sleep parameters:: bit 8:0 -- Gap bit 16:8 -- GPIO @@ -23,7 +21,8 @@ hscfgcmd where Gap is the gap in milli seconds between wakeup signal and wakeup event, or 0xff for special host sleep setting. - Usage: + Usage:: + # Use SDIO interface to wake up the host and set GAP to 0x80: echo 0xff80 > /debug/btmrvl/config/gpiogap echo 1 > /debug/btmrvl/config/hscfgcmd @@ -32,15 +31,16 @@ hscfgcmd echo 0x03ff > /debug/btmrvl/config/gpiogap echo 1 > /debug/btmrvl/config/hscfgcmd -psmode=[n] -pscmd +psmode=[n], pscmd These commands are used to enable/disable auto sleep mode - where the option is: + where the option is:: + 1 -- Enable auto sleep mode 0 -- Disable auto sleep mode - Usage: + Usage:: + # Enable auto sleep mode echo 1 > /debug/btmrvl/config/psmode echo 1 > /debug/btmrvl/config/pscmd @@ -50,15 +50,16 @@ pscmd echo 1 > /debug/btmrvl/config/pscmd -hsmode=[n] -hscmd +hsmode=[n], hscmd These commands are used to enable host sleep or wake up firmware - where the option is: + where the option is:: + 1 -- Enable host sleep 0 -- Wake up firmware - Usage: + Usage:: + # Enable host sleep echo 1 > /debug/btmrvl/config/hsmode echo 1 > /debug/btmrvl/config/hscmd @@ -68,12 +69,13 @@ hscmd echo 1 > /debug/btmrvl/config/hscmd -====================== -Get driver status: +Get driver status +================= Path: /debug/btmrvl/status/ -Usage: +Usage:: + cat /debug/btmrvl/status/<args> where the args are: @@ -90,14 +92,17 @@ hsstate txdnldrdy This command displays the value of Tx download ready flag. - -===================== +Issuing a raw hci command +========================= Use hcitool to issue raw hci command, refer to hcitool manual - Usage: Hcitool cmd <ogf> <ocf> [Parameters] +Usage:: + + Hcitool cmd <ogf> <ocf> [Parameters] + +Interface Control Command:: - Interface Control Command hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00 --Enable All interface hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01 --Enable Wlan interface hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02 --Enable BT interface @@ -105,13 +110,13 @@ Use hcitool to issue raw hci command, refer to hcitool manual hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01 --Disable Wlan interface hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02 --Disable BT interface -======================================================================= - +SD8688 firmware +=============== -SD8688 firmware: +Images: -/lib/firmware/sd8688_helper.bin -/lib/firmware/sd8688.bin +- /lib/firmware/sd8688_helper.bin +- /lib/firmware/sd8688.bin The images can be downloaded from: diff --git a/Documentation/bus-virt-phys-mapping.txt b/Documentation/bus-virt-phys-mapping.txt index 2bc55ff3b4d1..4bb07c2f3e7d 100644 --- a/Documentation/bus-virt-phys-mapping.txt +++ b/Documentation/bus-virt-phys-mapping.txt @@ -1,17 +1,27 @@ -[ NOTE: The virt_to_bus() and bus_to_virt() functions have been +========================================================== +How to access I/O mapped memory from within device drivers +========================================================== + +:Author: Linus + +.. warning:: + + The virt_to_bus() and bus_to_virt() functions have been superseded by the functionality provided by the PCI DMA interface (see Documentation/DMA-API-HOWTO.txt). They continue to be documented below for historical purposes, but new code - must not use them. --davidm 00/12/12 ] + must not use them. --davidm 00/12/12 -[ This is a mail message in response to a query on IO mapping, thus the - strange format for a "document" ] +:: + + [ This is a mail message in response to a query on IO mapping, thus the + strange format for a "document" ] The AHA-1542 is a bus-master device, and your patch makes the driver give the controller the physical address of the buffers, which is correct on x86 (because all bus master devices see the physical memory mappings directly). -However, on many setups, there are actually _three_ different ways of looking +However, on many setups, there are actually **three** different ways of looking at memory addresses, and in this case we actually want the third, the so-called "bus address". @@ -38,7 +48,7 @@ because the memory and the devices share the same address space, and that is not generally necessarily true on other PCI/ISA setups. Now, just as an example, on the PReP (PowerPC Reference Platform), the -CPU sees a memory map something like this (this is from memory): +CPU sees a memory map something like this (this is from memory):: 0-2 GB "real memory" 2 GB-3 GB "system IO" (inb/out and similar accesses on x86) @@ -52,7 +62,7 @@ So when the CPU wants any bus master to write to physical memory 0, it has to give the master address 0x80000000 as the memory address. So, for example, depending on how the kernel is actually mapped on the -PPC, you can end up with a setup like this: +PPC, you can end up with a setup like this:: physical address: 0 virtual address: 0xC0000000 @@ -61,7 +71,7 @@ PPC, you can end up with a setup like this: where all the addresses actually point to the same thing. It's just seen through different translations.. -Similarly, on the Alpha, the normal translation is +Similarly, on the Alpha, the normal translation is:: physical address: 0 virtual address: 0xfffffc0000000000 @@ -70,7 +80,7 @@ Similarly, on the Alpha, the normal translation is (but there are also Alphas where the physical address and the bus address are the same). -Anyway, the way to look up all these translations, you do +Anyway, the way to look up all these translations, you do:: #include <asm/io.h> @@ -81,8 +91,8 @@ Anyway, the way to look up all these translations, you do Now, when do you need these? -You want the _virtual_ address when you are actually going to access that -pointer from the kernel. So you can have something like this: +You want the **virtual** address when you are actually going to access that +pointer from the kernel. So you can have something like this:: /* * this is the hardware "mailbox" we use to communicate with @@ -104,7 +114,7 @@ pointer from the kernel. So you can have something like this: ... on the other hand, you want the bus address when you have a buffer that -you want to give to the controller: +you want to give to the controller:: /* ask the controller to read the sense status into "sense_buffer" */ mbox.bufstart = virt_to_bus(&sense_buffer); @@ -112,7 +122,7 @@ you want to give to the controller: mbox.status = 0; notify_controller(&mbox); -And you generally _never_ want to use the physical address, because you can't +And you generally **never** want to use the physical address, because you can't use that from the CPU (the CPU only uses translated virtual addresses), and you can't use it from the bus master. @@ -124,8 +134,10 @@ be remapped as measured in units of pages, a.k.a. the pfn (the memory management layer doesn't know about devices outside the CPU, so it shouldn't need to know about "bus addresses" etc). -NOTE NOTE NOTE! The above is only one part of the whole equation. The above -only talks about "real memory", that is, CPU memory (RAM). +.. note:: + + The above is only one part of the whole equation. The above + only talks about "real memory", that is, CPU memory (RAM). There is a completely different type of memory too, and that's the "shared memory" on the PCI or ISA bus. That's generally not RAM (although in the case @@ -137,20 +149,22 @@ whatever, and there is only one way to access it: the readb/writeb and related functions. You should never take the address of such memory, because there is really nothing you can do with such an address: it's not conceptually in the same memory space as "real memory" at all, so you cannot -just dereference a pointer. (Sadly, on x86 it _is_ in the same memory space, +just dereference a pointer. (Sadly, on x86 it **is** in the same memory space, so on x86 it actually works to just deference a pointer, but it's not portable). -For such memory, you can do things like +For such memory, you can do things like: + + - reading:: - - reading: /* * read first 32 bits from ISA memory at 0xC0000, aka * C000:0000 in DOS terms */ unsigned int signature = isa_readl(0xC0000); - - remapping and writing: + - remapping and writing:: + /* * remap framebuffer PCI memory area at 0xFC000000, * size 1MB, so that we can access it: We can directly @@ -165,7 +179,8 @@ For such memory, you can do things like /* unmap when we unload the driver */ iounmap(baseptr); - - copying and clearing: + - copying and clearing:: + /* get the 6-byte Ethernet address at ISA address E000:0040 */ memcpy_fromio(kernel_buffer, 0xE0040, 6); /* write a packet to the driver */ @@ -181,10 +196,10 @@ happy that your driver works ;) Note that kernel versions 2.0.x (and earlier) mistakenly called the ioremap() function "vremap()". ioremap() is the proper name, but I didn't think straight when I wrote it originally. People who have to -support both can do something like: +support both can do something like:: /* support old naming silliness */ - #if LINUX_VERSION_CODE < 0x020100 + #if LINUX_VERSION_CODE < 0x020100 #define ioremap vremap #define iounmap vfree #endif @@ -196,13 +211,10 @@ And the above sounds worse than it really is. Most real drivers really don't do all that complex things (or rather: the complexity is not so much in the actual IO accesses as in error handling and timeouts etc). It's generally not hard to fix drivers, and in many cases the code -actually looks better afterwards: +actually looks better afterwards:: unsigned long signature = *(unsigned int *) 0xC0000; vs unsigned long signature = readl(0xC0000); I think the second version actually is more readable, no? - - Linus - diff --git a/Documentation/cachetlb.txt b/Documentation/cachetlb.txt index 3f9f808b5119..6eb9d3f090cd 100644 --- a/Documentation/cachetlb.txt +++ b/Documentation/cachetlb.txt @@ -1,7 +1,8 @@ - Cache and TLB Flushing - Under Linux +================================== +Cache and TLB Flushing Under Linux +================================== - David S. Miller <davem@redhat.com> +:Author: David S. Miller <davem@redhat.com> This document describes the cache/tlb flushing interfaces called by the Linux VM subsystem. It enumerates over each interface, @@ -28,7 +29,7 @@ Therefore when software page table changes occur, the kernel will invoke one of the following flush methods _after_ the page table changes occur: -1) void flush_tlb_all(void) +1) ``void flush_tlb_all(void)`` The most severe flush of all. After this interface runs, any previous page table modification whatsoever will be @@ -37,7 +38,7 @@ changes occur: This is usually invoked when the kernel page tables are changed, since such translations are "global" in nature. -2) void flush_tlb_mm(struct mm_struct *mm) +2) ``void flush_tlb_mm(struct mm_struct *mm)`` This interface flushes an entire user address space from the TLB. After running, this interface must make sure that @@ -49,8 +50,8 @@ changes occur: page table operations such as what happens during fork, and exec. -3) void flush_tlb_range(struct vm_area_struct *vma, - unsigned long start, unsigned long end) +3) ``void flush_tlb_range(struct vm_area_struct *vma, + unsigned long start, unsigned long end)`` Here we are flushing a specific range of (user) virtual address translations from the TLB. After running, this @@ -69,7 +70,7 @@ changes occur: call flush_tlb_page (see below) for each entry which may be modified. -4) void flush_tlb_page(struct vm_area_struct *vma, unsigned long addr) +4) ``void flush_tlb_page(struct vm_area_struct *vma, unsigned long addr)`` This time we need to remove the PAGE_SIZE sized translation from the TLB. The 'vma' is the backing structure used by @@ -87,8 +88,8 @@ changes occur: This is used primarily during fault processing. -5) void update_mmu_cache(struct vm_area_struct *vma, - unsigned long address, pte_t *ptep) +5) ``void update_mmu_cache(struct vm_area_struct *vma, + unsigned long address, pte_t *ptep)`` At the end of every page fault, this routine is invoked to tell the architecture specific code that a translation @@ -100,7 +101,7 @@ changes occur: translations for software managed TLB configurations. The sparc64 port currently does this. -6) void tlb_migrate_finish(struct mm_struct *mm) +6) ``void tlb_migrate_finish(struct mm_struct *mm)`` This interface is called at the end of an explicit process migration. This interface provides a hook @@ -112,7 +113,7 @@ changes occur: Next, we have the cache flushing interfaces. In general, when Linux is changing an existing virtual-->physical mapping to a new value, -the sequence will be in one of the following forms: +the sequence will be in one of the following forms:: 1) flush_cache_mm(mm); change_all_page_tables_of(mm); @@ -143,7 +144,7 @@ and have no dependency on translation information. Here are the routines, one by one: -1) void flush_cache_mm(struct mm_struct *mm) +1) ``void flush_cache_mm(struct mm_struct *mm)`` This interface flushes an entire user address space from the caches. That is, after running, there will be no cache @@ -152,7 +153,7 @@ Here are the routines, one by one: This interface is used to handle whole address space page table operations such as what happens during exit and exec. -2) void flush_cache_dup_mm(struct mm_struct *mm) +2) ``void flush_cache_dup_mm(struct mm_struct *mm)`` This interface flushes an entire user address space from the caches. That is, after running, there will be no cache @@ -164,8 +165,8 @@ Here are the routines, one by one: This option is separate from flush_cache_mm to allow some optimizations for VIPT caches. -3) void flush_cache_range(struct vm_area_struct *vma, - unsigned long start, unsigned long end) +3) ``void flush_cache_range(struct vm_area_struct *vma, + unsigned long start, unsigned long end)`` Here we are flushing a specific range of (user) virtual addresses from the cache. After running, there will be no @@ -181,7 +182,7 @@ Here are the routines, one by one: call flush_cache_page (see below) for each entry which may be modified. -4) void flush_cache_page(struct vm_area_struct *vma, unsigned long addr, unsigned long pfn) +4) ``void flush_cache_page(struct vm_area_struct *vma, unsigned long addr, unsigned long pfn)`` This time we need to remove a PAGE_SIZE sized range from the cache. The 'vma' is the backing structure used by @@ -202,7 +203,7 @@ Here are the routines, one by one: This is used primarily during fault processing. -5) void flush_cache_kmaps(void) +5) ``void flush_cache_kmaps(void)`` This routine need only be implemented if the platform utilizes highmem. It will be called right before all of the kmaps @@ -214,8 +215,8 @@ Here are the routines, one by one: This routing should be implemented in asm/highmem.h -6) void flush_cache_vmap(unsigned long start, unsigned long end) - void flush_cache_vunmap(unsigned long start, unsigned long end) +6) ``void flush_cache_vmap(unsigned long start, unsigned long end)`` + ``void flush_cache_vunmap(unsigned long start, unsigned long end)`` Here in these two interfaces we are flushing a specific range of (kernel) virtual addresses from the cache. After running, @@ -243,8 +244,10 @@ size). This setting will force the SYSv IPC layer to only allow user processes to mmap shared memory at address which are a multiple of this value. -NOTE: This does not fix shared mmaps, check out the sparc64 port for -one way to solve this (in particular SPARC_FLAG_MMAPSHARED). +.. note:: + + This does not fix shared mmaps, check out the sparc64 port for + one way to solve this (in particular SPARC_FLAG_MMAPSHARED). Next, you have to solve the D-cache aliasing issue for all other cases. Please keep in mind that fact that, for a given page @@ -255,8 +258,8 @@ physical page into its address space, by implication the D-cache aliasing problem has the potential to exist since the kernel already maps this page at its virtual address. - void copy_user_page(void *to, void *from, unsigned long addr, struct page *page) - void clear_user_page(void *to, unsigned long addr, struct page *page) + ``void copy_user_page(void *to, void *from, unsigned long addr, struct page *page)`` + ``void clear_user_page(void *to, unsigned long addr, struct page *page)`` These two routines store data in user anonymous or COW pages. It allows a port to efficiently avoid D-cache alias @@ -276,14 +279,16 @@ maps this page at its virtual address. If D-cache aliasing is not an issue, these two routines may simply call memcpy/memset directly and do nothing more. - void flush_dcache_page(struct page *page) + ``void flush_dcache_page(struct page *page)`` Any time the kernel writes to a page cache page, _OR_ the kernel is about to read from a page cache page and user space shared/writable mappings of this page potentially exist, this routine is called. - NOTE: This routine need only be called for page cache pages + .. note:: + + This routine need only be called for page cache pages which can potentially ever be mapped into the address space of a user process. So for example, VFS layer code handling vfs symlinks in the page cache need not call @@ -322,18 +327,19 @@ maps this page at its virtual address. made of this flag bit, and if set the flush is done and the flag bit is cleared. - IMPORTANT NOTE: It is often important, if you defer the flush, + .. important:: + + It is often important, if you defer the flush, that the actual flush occurs on the same CPU as did the cpu stores into the page to make it dirty. Again, see sparc64 for examples of how to deal with this. - void copy_to_user_page(struct vm_area_struct *vma, struct page *page, - unsigned long user_vaddr, - void *dst, void *src, int len) - void copy_from_user_page(struct vm_area_struct *vma, struct page *page, - unsigned long user_vaddr, - void *dst, void *src, int len) + ``void copy_to_user_page(struct vm_area_struct *vma, struct page *page, + unsigned long user_vaddr, void *dst, void *src, int len)`` + ``void copy_from_user_page(struct vm_area_struct *vma, struct page *page, + unsigned long user_vaddr, void *dst, void *src, int len)`` + When the kernel needs to copy arbitrary data in and out of arbitrary user pages (f.e. for ptrace()) it will use these two routines. @@ -344,8 +350,9 @@ maps this page at its virtual address. likely that you will need to flush the instruction cache for copy_to_user_page(). - void flush_anon_page(struct vm_area_struct *vma, struct page *page, - unsigned long vmaddr) + ``void flush_anon_page(struct vm_area_struct *vma, struct page *page, + unsigned long vmaddr)`` + When the kernel needs to access the contents of an anonymous page, it calls this function (currently only get_user_pages()). Note: flush_dcache_page() deliberately @@ -354,7 +361,8 @@ maps this page at its virtual address. architectures). For incoherent architectures, it should flush the cache of the page at vmaddr. - void flush_kernel_dcache_page(struct page *page) + ``void flush_kernel_dcache_page(struct page *page)`` + When the kernel needs to modify a user page is has obtained with kmap, it calls this function after all modifications are complete (but before kunmapping it) to bring the underlying @@ -366,14 +374,16 @@ maps this page at its virtual address. the kernel cache for page (using page_address(page)). - void flush_icache_range(unsigned long start, unsigned long end) + ``void flush_icache_range(unsigned long start, unsigned long end)`` + When the kernel stores into addresses that it will execute out of (eg when loading modules), this function is called. If the icache does not snoop stores then this routine will need to flush it. - void flush_icache_page(struct vm_area_struct *vma, struct page *page) + ``void flush_icache_page(struct vm_area_struct *vma, struct page *page)`` + All the functionality of flush_icache_page can be implemented in flush_dcache_page and update_mmu_cache. In the future, the hope is to remove this interface completely. @@ -387,7 +397,8 @@ the kernel trying to do I/O to vmap areas must manually manage coherency. It must do this by flushing the vmap range before doing I/O and invalidating it after the I/O returns. - void flush_kernel_vmap_range(void *vaddr, int size) + ``void flush_kernel_vmap_range(void *vaddr, int size)`` + flushes the kernel cache for a given virtual address range in the vmap area. This is to make sure that any data the kernel modified in the vmap range is made visible to the physical @@ -395,7 +406,8 @@ I/O and invalidating it after the I/O returns. Note that this API does *not* also flush the offset map alias of the area. - void invalidate_kernel_vmap_range(void *vaddr, int size) invalidates + ``void invalidate_kernel_vmap_range(void *vaddr, int size) invalidates`` + the cache for a given virtual address range in the vmap area which prevents the processor from making the cache stale by speculatively reading data while the I/O was occurring to the diff --git a/Documentation/cgroup-v1/memory.txt b/Documentation/cgroup-v1/memory.txt index 946e69103cdd..cefb63639070 100644 --- a/Documentation/cgroup-v1/memory.txt +++ b/Documentation/cgroup-v1/memory.txt @@ -789,23 +789,46 @@ way to trigger. Applications should do whatever they can to help the system. It might be too late to consult with vmstat or any other statistics, so it's advisable to take an immediate action. -The events are propagated upward until the event is handled, i.e. the -events are not pass-through. Here is what this means: for example you have -three cgroups: A->B->C. Now you set up an event listener on cgroups A, B -and C, and suppose group C experiences some pressure. In this situation, -only group C will receive the notification, i.e. groups A and B will not -receive it. This is done to avoid excessive "broadcasting" of messages, -which disturbs the system and which is especially bad if we are low on -memory or thrashing. So, organize the cgroups wisely, or propagate the -events manually (or, ask us to implement the pass-through events, -explaining why would you need them.) +By default, events are propagated upward until the event is handled, i.e. the +events are not pass-through. For example, you have three cgroups: A->B->C. Now +you set up an event listener on cgroups A, B and C, and suppose group C +experiences some pressure. In this situation, only group C will receive the +notification, i.e. groups A and B will not receive it. This is done to avoid +excessive "broadcasting" of messages, which disturbs the system and which is +especially bad if we are low on memory or thrashing. Group B, will receive +notification only if there are no event listers for group C. + +There are three optional modes that specify different propagation behavior: + + - "default": this is the default behavior specified above. This mode is the + same as omitting the optional mode parameter, preserved by backwards + compatibility. + + - "hierarchy": events always propagate up to the root, similar to the default + behavior, except that propagation continues regardless of whether there are + event listeners at each level, with the "hierarchy" mode. In the above + example, groups A, B, and C will receive notification of memory pressure. + + - "local": events are pass-through, i.e. they only receive notifications when + memory pressure is experienced in the memcg for which the notification is + registered. In the above example, group C will receive notification if + registered for "local" notification and the group experiences memory + pressure. However, group B will never receive notification, regardless if + there is an event listener for group C or not, if group B is registered for + local notification. + +The level and event notification mode ("hierarchy" or "local", if necessary) are +specified by a comma-delimited string, i.e. "low,hierarchy" specifies +hierarchical, pass-through, notification for all ancestor memcgs. Notification +that is the default, non pass-through behavior, does not specify a mode. +"medium,local" specifies pass-through notification for the medium level. The file memory.pressure_level is only used to setup an eventfd. To register a notification, an application must: - create an eventfd using eventfd(2); - open memory.pressure_level; -- write string like "<event_fd> <fd of memory.pressure_level> <level>" +- write string as "<event_fd> <fd of memory.pressure_level> <level[,mode]>" to cgroup.event_control. Application will be notified through eventfd when memory pressure is at @@ -821,7 +844,7 @@ Test: # cd /sys/fs/cgroup/memory/ # mkdir foo # cd foo - # cgroup_event_listener memory.pressure_level low & + # cgroup_event_listener memory.pressure_level low,hierarchy & # echo 8000000 > memory.limit_in_bytes # echo 8000000 > memory.memsw.limit_in_bytes # echo $$ > tasks diff --git a/Documentation/cgroup-v2.txt b/Documentation/cgroup-v2.txt index e6101976e0f1..bde177103567 100644 --- a/Documentation/cgroup-v2.txt +++ b/Documentation/cgroup-v2.txt @@ -1,7 +1,9 @@ - +================ Control Group v2 +================ -October, 2015 Tejun Heo <tj@kernel.org> +:Date: October, 2015 +:Author: Tejun Heo <tj@kernel.org> This is the authoritative documentation on the design, interface and conventions of cgroup v2. It describes all userland-visible aspects @@ -9,70 +11,72 @@ of cgroup including core and specific controller behaviors. All future changes must be reflected in this document. Documentation for v1 is available under Documentation/cgroup-v1/. -CONTENTS - -1. Introduction - 1-1. Terminology - 1-2. What is cgroup? -2. Basic Operations - 2-1. Mounting - 2-2. Organizing Processes - 2-3. [Un]populated Notification - 2-4. Controlling Controllers - 2-4-1. Enabling and Disabling - 2-4-2. Top-down Constraint - 2-4-3. No Internal Process Constraint - 2-5. Delegation - 2-5-1. Model of Delegation - 2-5-2. Delegation Containment - 2-6. Guidelines - 2-6-1. Organize Once and Control - 2-6-2. Avoid Name Collisions -3. Resource Distribution Models - 3-1. Weights - 3-2. Limits - 3-3. Protections - 3-4. Allocations -4. Interface Files - 4-1. Format - 4-2. Conventions - 4-3. Core Interface Files -5. Controllers - 5-1. CPU - 5-1-1. CPU Interface Files - 5-2. Memory - 5-2-1. Memory Interface Files - 5-2-2. Usage Guidelines - 5-2-3. Memory Ownership - 5-3. IO - 5-3-1. IO Interface Files - 5-3-2. Writeback - 5-4. PID - 5-4-1. PID Interface Files - 5-5. RDMA - 5-5-1. RDMA Interface Files - 5-6. Misc - 5-6-1. perf_event -6. Namespace - 6-1. Basics - 6-2. The Root and Views - 6-3. Migration and setns(2) - 6-4. Interaction with Other Namespaces -P. Information on Kernel Programming - P-1. Filesystem Support for Writeback -D. Deprecated v1 Core Features -R. Issues with v1 and Rationales for v2 - R-1. Multiple Hierarchies - R-2. Thread Granularity - R-3. Competition Between Inner Nodes and Threads - R-4. Other Interface Issues - R-5. Controller Issues and Remedies - R-5-1. Memory - - -1. Introduction - -1-1. Terminology +.. CONTENTS + + 1. Introduction + 1-1. Terminology + 1-2. What is cgroup? + 2. Basic Operations + 2-1. Mounting + 2-2. Organizing Processes + 2-3. [Un]populated Notification + 2-4. Controlling Controllers + 2-4-1. Enabling and Disabling + 2-4-2. Top-down Constraint + 2-4-3. No Internal Process Constraint + 2-5. Delegation + 2-5-1. Model of Delegation + 2-5-2. Delegation Containment + 2-6. Guidelines + 2-6-1. Organize Once and Control + 2-6-2. Avoid Name Collisions + 3. Resource Distribution Models + 3-1. Weights + 3-2. Limits + 3-3. Protections + 3-4. Allocations + 4. Interface Files + 4-1. Format + 4-2. Conventions + 4-3. Core Interface Files + 5. Controllers + 5-1. CPU + 5-1-1. CPU Interface Files + 5-2. Memory + 5-2-1. Memory Interface Files + 5-2-2. Usage Guidelines + 5-2-3. Memory Ownership + 5-3. IO + 5-3-1. IO Interface Files + 5-3-2. Writeback + 5-4. PID + 5-4-1. PID Interface Files + 5-5. RDMA + 5-5-1. RDMA Interface Files + 5-6. Misc + 5-6-1. perf_event + 6. Namespace + 6-1. Basics + 6-2. The Root and Views + 6-3. Migration and setns(2) + 6-4. Interaction with Other Namespaces + P. Information on Kernel Programming + P-1. Filesystem Support for Writeback + D. Deprecated v1 Core Features + R. Issues with v1 and Rationales for v2 + R-1. Multiple Hierarchies + R-2. Thread Granularity + R-3. Competition Between Inner Nodes and Threads + R-4. Other Interface Issues + R-5. Controller Issues and Remedies + R-5-1. Memory + + +Introduction +============ + +Terminology +----------- "cgroup" stands for "control group" and is never capitalized. The singular form is used to designate the whole feature and also as a @@ -80,7 +84,8 @@ qualifier as in "cgroup controllers". When explicitly referring to multiple individual control groups, the plural form "cgroups" is used. -1-2. What is cgroup? +What is cgroup? +--------------- cgroup is a mechanism to organize processes hierarchically and distribute system resources along the hierarchy in a controlled and @@ -110,12 +115,14 @@ restrictions set closer to the root in the hierarchy can not be overridden from further away. -2. Basic Operations +Basic Operations +================ -2-1. Mounting +Mounting +-------- Unlike v1, cgroup v2 has only single hierarchy. The cgroup v2 -hierarchy can be mounted with the following mount command. +hierarchy can be mounted with the following mount command:: # mount -t cgroup2 none $MOUNT_POINT @@ -160,10 +167,11 @@ cgroup v2 currently supports the following mount options. Delegation section for details. -2-2. Organizing Processes +Organizing Processes +-------------------- Initially, only the root cgroup exists to which all processes belong. -A child cgroup can be created by creating a sub-directory. +A child cgroup can be created by creating a sub-directory:: # mkdir $CGROUP_NAME @@ -190,28 +198,29 @@ moved to another cgroup. A cgroup which doesn't have any children or live processes can be destroyed by removing the directory. Note that a cgroup which doesn't have any children and is associated only with zombie processes is -considered empty and can be removed. +considered empty and can be removed:: # rmdir $CGROUP_NAME "/proc/$PID/cgroup" lists a process's cgroup membership. If legacy cgroup is in use in the system, this file may contain multiple lines, one for each hierarchy. The entry for cgroup v2 is always in the -format "0::$PATH". +format "0::$PATH":: # cat /proc/842/cgroup ... 0::/test-cgroup/test-cgroup-nested If the process becomes a zombie and the cgroup it was associated with -is removed subsequently, " (deleted)" is appended to the path. +is removed subsequently, " (deleted)" is appended to the path:: # cat /proc/842/cgroup ... 0::/test-cgroup/test-cgroup-nested (deleted) -2-3. [Un]populated Notification +[Un]populated Notification +-------------------------- Each non-root cgroup has a "cgroup.events" file which contains "populated" field indicating whether the cgroup's sub-hierarchy has @@ -222,7 +231,7 @@ example, to start a clean-up operation after all processes of a given sub-hierarchy have exited. The populated state updates and notifications are recursive. Consider the following sub-hierarchy where the numbers in the parentheses represent the numbers of processes -in each cgroup. +in each cgroup:: A(4) - B(0) - C(1) \ D(0) @@ -233,18 +242,20 @@ file modified events will be generated on the "cgroup.events" files of both cgroups. -2-4. Controlling Controllers +Controlling Controllers +----------------------- -2-4-1. Enabling and Disabling +Enabling and Disabling +~~~~~~~~~~~~~~~~~~~~~~ Each cgroup has a "cgroup.controllers" file which lists all -controllers available for the cgroup to enable. +controllers available for the cgroup to enable:: # cat cgroup.controllers cpu io memory No controller is enabled by default. Controllers can be enabled and -disabled by writing to the "cgroup.subtree_control" file. +disabled by writing to the "cgroup.subtree_control" file:: # echo "+cpu +memory -io" > cgroup.subtree_control @@ -256,7 +267,7 @@ are specified, the last one is effective. Enabling a controller in a cgroup indicates that the distribution of the target resource across its immediate children will be controlled. Consider the following sub-hierarchy. The enabled controllers are -listed in parentheses. +listed in parentheses:: A(cpu,memory) - B(memory) - C() \ D() @@ -276,7 +287,8 @@ controller interface files - anything which doesn't start with "cgroup." are owned by the parent rather than the cgroup itself. -2-4-2. Top-down Constraint +Top-down Constraint +~~~~~~~~~~~~~~~~~~~ Resources are distributed top-down and a cgroup can further distribute a resource only if the resource has been distributed to it from the @@ -287,7 +299,8 @@ the parent has the controller enabled and a controller can't be disabled if one or more children have it enabled. -2-4-3. No Internal Process Constraint +No Internal Process Constraint +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Non-root cgroups can only distribute resources to their children when they don't have any processes of their own. In other words, only @@ -314,9 +327,11 @@ children before enabling controllers in its "cgroup.subtree_control" file. -2-5. Delegation +Delegation +---------- -2-5-1. Model of Delegation +Model of Delegation +~~~~~~~~~~~~~~~~~~~ A cgroup can be delegated in two ways. First, to a less privileged user by granting write access of the directory and its "cgroup.procs" @@ -345,7 +360,8 @@ cgroups in or nesting depth of a delegated sub-hierarchy; however, this may be limited explicitly in the future. -2-5-2. Delegation Containment +Delegation Containment +~~~~~~~~~~~~~~~~~~~~~~ A delegated sub-hierarchy is contained in the sense that processes can't be moved into or out of the sub-hierarchy by the delegatee. @@ -366,7 +382,7 @@ in from or push out to outside the sub-hierarchy. For an example, let's assume cgroups C0 and C1 have been delegated to user U0 who created C00, C01 under C0 and C10 under C1 as follows and -all processes under C0 and C1 belong to U0. +all processes under C0 and C1 belong to U0:: ~~~~~~~~~~~~~ - C0 - C00 ~ cgroup ~ \ C01 @@ -386,9 +402,11 @@ namespace of the process which is attempting the migration. If either is not reachable, the migration is rejected with -ENOENT. -2-6. Guidelines +Guidelines +---------- -2-6-1. Organize Once and Control +Organize Once and Control +~~~~~~~~~~~~~~~~~~~~~~~~~ Migrating a process across cgroups is a relatively expensive operation and stateful resources such as memory are not moved together with the @@ -404,7 +422,8 @@ distribution can be made by changing controller configuration through the interface files. -2-6-2. Avoid Name Collisions +Avoid Name Collisions +~~~~~~~~~~~~~~~~~~~~~ Interface files for a cgroup and its children cgroups occupy the same directory and it is possible to create children cgroups which collide @@ -422,14 +441,16 @@ cgroup doesn't do anything to prevent name collisions and it's the user's responsibility to avoid them. -3. Resource Distribution Models +Resource Distribution Models +============================ cgroup controllers implement several resource distribution schemes depending on the resource type and expected use cases. This section describes major schemes in use along with their expected behaviors. -3-1. Weights +Weights +------- A parent's resource is distributed by adding up the weights of all active children and giving each the fraction matching the ratio of its @@ -450,7 +471,8 @@ process migrations. and is an example of this type. -3-2. Limits +Limits +------ A child can only consume upto the configured amount of the resource. Limits can be over-committed - the sum of the limits of children can @@ -466,7 +488,8 @@ process migrations. on an IO device and is an example of this type. -3-3. Protections +Protections +----------- A cgroup is protected to be allocated upto the configured amount of the resource if the usages of all its ancestors are under their @@ -486,7 +509,8 @@ process migrations. example of this type. -3-4. Allocations +Allocations +----------- A cgroup is exclusively allocated a certain amount of a finite resource. Allocations can't be over-committed - the sum of the @@ -505,12 +529,14 @@ may be rejected. type. -4. Interface Files +Interface Files +=============== -4-1. Format +Format +------ All interface files should be in one of the following formats whenever -possible. +possible:: New-line separated values (when only one value can be written at once) @@ -545,7 +571,8 @@ can be written at a time. For nested keyed files, the sub key pairs may be specified in any order and not all pairs have to be specified. -4-2. Conventions +Conventions +----------- - Settings for a single feature should be contained in a single file. @@ -581,25 +608,25 @@ may be specified in any order and not all pairs have to be specified. with "default" as the value must not appear when read. For example, a setting which is keyed by major:minor device numbers - with integer values may look like the following. + with integer values may look like the following:: # cat cgroup-example-interface-file default 150 8:0 300 - The default value can be updated by + The default value can be updated by:: # echo 125 > cgroup-example-interface-file - or + or:: # echo "default 125" > cgroup-example-interface-file - An override can be set by + An override can be set by:: # echo "8:16 170" > cgroup-example-interface-file - and cleared by + and cleared by:: # echo "8:0 default" > cgroup-example-interface-file # cat cgroup-example-interface-file @@ -612,12 +639,12 @@ may be specified in any order and not all pairs have to be specified. generated on the file. -4-3. Core Interface Files +Core Interface Files +-------------------- All cgroup core files are prefixed with "cgroup." cgroup.procs - A read-write new-line separated values file which exists on all cgroups. @@ -643,7 +670,6 @@ All cgroup core files are prefixed with "cgroup." should be granted along with the containing directory. cgroup.controllers - A read-only space separated values file which exists on all cgroups. @@ -651,7 +677,6 @@ All cgroup core files are prefixed with "cgroup." the cgroup. The controllers are not ordered. cgroup.subtree_control - A read-write space separated values file which exists on all cgroups. Starts out empty. @@ -667,23 +692,25 @@ All cgroup core files are prefixed with "cgroup." operations are specified, either all succeed or all fail. cgroup.events - A read-only flat-keyed file which exists on non-root cgroups. The following entries are defined. Unless specified otherwise, a value change in this file generates a file modified event. populated - 1 if the cgroup or its descendants contains any live processes; otherwise, 0. -5. Controllers +Controllers +=========== -5-1. CPU +CPU +--- -[NOTE: The interface for the cpu controller hasn't been merged yet] +.. note:: + + The interface for the cpu controller hasn't been merged yet The "cpu" controllers regulates distribution of CPU cycles. This controller implements weight and absolute bandwidth limit models for @@ -691,36 +718,34 @@ normal scheduling policy and absolute bandwidth allocation model for realtime scheduling policy. -5-1-1. CPU Interface Files +CPU Interface Files +~~~~~~~~~~~~~~~~~~~ All time durations are in microseconds. cpu.stat - A read-only flat-keyed file which exists on non-root cgroups. - It reports the following six stats. + It reports the following six stats: - usage_usec - user_usec - system_usec - nr_periods - nr_throttled - throttled_usec + - usage_usec + - user_usec + - system_usec + - nr_periods + - nr_throttled + - throttled_usec cpu.weight - A read-write single value file which exists on non-root cgroups. The default is "100". The weight in the range [1, 10000]. cpu.max - A read-write two value file which exists on non-root cgroups. The default is "max 100000". - The maximum bandwidth limit. It's in the following format. + The maximum bandwidth limit. It's in the following format:: $MAX $PERIOD @@ -729,9 +754,10 @@ All time durations are in microseconds. one number is written, $MAX is updated. cpu.rt.max + .. note:: - [NOTE: The semantics of this file is still under discussion and the - interface hasn't been merged yet] + The semantics of this file is still under discussion and the + interface hasn't been merged yet A read-write two value file which exists on all cgroups. The default is "0 100000". @@ -739,7 +765,7 @@ All time durations are in microseconds. The maximum realtime runtime allocation. Over-committing configurations are disallowed and process migrations are rejected if not enough bandwidth is available. It's in the - following format. + following format:: $MAX $PERIOD @@ -748,7 +774,8 @@ All time durations are in microseconds. updated. -5-2. Memory +Memory +------ The "memory" controller regulates distribution of memory. Memory is stateful and implements both limit and protection models. Due to the @@ -770,14 +797,14 @@ following types of memory usages are tracked. The above list may expand in the future for better coverage. -5-2-1. Memory Interface Files +Memory Interface Files +~~~~~~~~~~~~~~~~~~~~~~ All memory amounts are in bytes. If a value which is not aligned to PAGE_SIZE is written, the value may be rounded up to the closest PAGE_SIZE multiple when read back. memory.current - A read-only single value file which exists on non-root cgroups. @@ -785,7 +812,6 @@ PAGE_SIZE multiple when read back. and its descendants. memory.low - A read-write single value file which exists on non-root cgroups. The default is "0". @@ -798,7 +824,6 @@ PAGE_SIZE multiple when read back. protection is discouraged. memory.high - A read-write single value file which exists on non-root cgroups. The default is "max". @@ -811,7 +836,6 @@ PAGE_SIZE multiple when read back. under extreme conditions the limit may be breached. memory.max - A read-write single value file which exists on non-root cgroups. The default is "max". @@ -826,21 +850,18 @@ PAGE_SIZE multiple when read back. utility is limited to providing the final safety net. memory.events - A read-only flat-keyed file which exists on non-root cgroups. The following entries are defined. Unless specified otherwise, a value change in this file generates a file modified event. low - The number of times the cgroup is reclaimed due to high memory pressure even though its usage is under the low boundary. This usually indicates that the low boundary is over-committed. high - The number of times processes of the cgroup are throttled and routed to perform direct memory reclaim because the high memory boundary was exceeded. For a @@ -849,13 +870,11 @@ PAGE_SIZE multiple when read back. occurrences are expected. max - The number of times the cgroup's memory usage was about to go over the max boundary. If direct reclaim fails to bring it down, the cgroup goes to OOM state. oom - The number of time the cgroup's memory usage was reached the limit and allocation was about to fail. @@ -864,16 +883,14 @@ PAGE_SIZE multiple when read back. Failed allocation in its turn could be returned into userspace as -ENOMEM or siletly ignored in cases like - disk readahead. For now OOM in memory cgroup kills + disk readahead. For now OOM in memory cgroup kills tasks iff shortage has happened inside page fault. oom_kill - The number of processes belonging to this cgroup killed by any kind of OOM killer. memory.stat - A read-only flat-keyed file which exists on non-root cgroups. This breaks down the cgroup's memory footprint into different @@ -887,73 +904,55 @@ PAGE_SIZE multiple when read back. fixed position; use the keys to look up specific values! anon - Amount of memory used in anonymous mappings such as brk(), sbrk(), and mmap(MAP_ANONYMOUS) file - Amount of memory used to cache filesystem data, including tmpfs and shared memory. kernel_stack - Amount of memory allocated to kernel stacks. slab - Amount of memory used for storing in-kernel data structures. sock - Amount of memory used in network transmission buffers shmem - Amount of cached filesystem data that is swap-backed, such as tmpfs, shm segments, shared anonymous mmap()s file_mapped - Amount of cached filesystem data mapped with mmap() file_dirty - Amount of cached filesystem data that was modified but not yet written back to disk file_writeback - Amount of cached filesystem data that was modified and is currently being written back to disk - inactive_anon - active_anon - inactive_file - active_file - unevictable - + inactive_anon, active_anon, inactive_file, active_file, unevictable Amount of memory, swap-backed and filesystem-backed, on the internal memory management lists used by the page reclaim algorithm slab_reclaimable - Part of "slab" that might be reclaimed, such as dentries and inodes. slab_unreclaimable - Part of "slab" that cannot be reclaimed on memory pressure. pgfault - Total number of page faults incurred pgmajfault - Number of major page faults incurred workingset_refault @@ -997,7 +996,6 @@ PAGE_SIZE multiple when read back. Amount of reclaimed lazyfree pages memory.swap.current - A read-only single value file which exists on non-root cgroups. @@ -1005,7 +1003,6 @@ PAGE_SIZE multiple when read back. and its descendants. memory.swap.max - A read-write single value file which exists on non-root cgroups. The default is "max". @@ -1013,7 +1010,8 @@ PAGE_SIZE multiple when read back. limit, anonymous meomry of the cgroup will not be swapped out. -5-2-2. Usage Guidelines +Usage Guidelines +~~~~~~~~~~~~~~~~ "memory.high" is the main mechanism to control memory usage. Over-committing on high limit (sum of high limits > available memory) @@ -1036,7 +1034,8 @@ memory; unfortunately, memory pressure monitoring mechanism isn't implemented yet. -5-2-3. Memory Ownership +Memory Ownership +~~~~~~~~~~~~~~~~ A memory area is charged to the cgroup which instantiated it and stays charged to the cgroup until the area is released. Migrating a process @@ -1054,7 +1053,8 @@ POSIX_FADV_DONTNEED to relinquish the ownership of memory areas belonging to the affected files to ensure correct memory ownership. -5-3. IO +IO +-- The "io" controller regulates the distribution of IO resources. This controller implements both weight based and absolute bandwidth or IOPS @@ -1063,28 +1063,29 @@ only if cfq-iosched is in use and neither scheme is available for blk-mq devices. -5-3-1. IO Interface Files +IO Interface Files +~~~~~~~~~~~~~~~~~~ io.stat - A read-only nested-keyed file which exists on non-root cgroups. Lines are keyed by $MAJ:$MIN device numbers and not ordered. The following nested keys are defined. + ====== =================== rbytes Bytes read wbytes Bytes written rios Number of read IOs wios Number of write IOs + ====== =================== - An example read output follows. + An example read output follows: 8:16 rbytes=1459200 wbytes=314773504 rios=192 wios=353 8:0 rbytes=90430464 wbytes=299008000 rios=8950 wios=1252 io.weight - A read-write flat-keyed file which exists on non-root cgroups. The default is "default 100". @@ -1098,14 +1099,13 @@ blk-mq devices. $WEIGHT" or simply "$WEIGHT". Overrides can be set by writing "$MAJ:$MIN $WEIGHT" and unset by writing "$MAJ:$MIN default". - An example read output follows. + An example read output follows:: default 100 8:16 200 8:0 50 io.max - A read-write nested-keyed file which exists on non-root cgroups. @@ -1113,10 +1113,12 @@ blk-mq devices. device numbers and not ordered. The following nested keys are defined. + ===== ================================== rbps Max read bytes per second wbps Max write bytes per second riops Max read IO operations per second wiops Max write IO operations per second + ===== ================================== When writing, any number of nested key-value pairs can be specified in any order. "max" can be specified as the value @@ -1126,24 +1128,25 @@ blk-mq devices. BPS and IOPS are measured in each IO direction and IOs are delayed if limit is reached. Temporary bursts are allowed. - Setting read limit at 2M BPS and write at 120 IOPS for 8:16. + Setting read limit at 2M BPS and write at 120 IOPS for 8:16:: echo "8:16 rbps=2097152 wiops=120" > io.max - Reading returns the following. + Reading returns the following:: 8:16 rbps=2097152 wbps=max riops=max wiops=120 - Write IOPS limit can be removed by writing the following. + Write IOPS limit can be removed by writing the following:: echo "8:16 wiops=max" > io.max - Reading now returns the following. + Reading now returns the following:: 8:16 rbps=2097152 wbps=max riops=max wiops=max -5-3-2. Writeback +Writeback +~~~~~~~~~ Page cache is dirtied through buffered writes and shared mmaps and written asynchronously to the backing filesystem by the writeback @@ -1191,22 +1194,19 @@ patterns. The sysctl knobs which affect writeback behavior are applied to cgroup writeback as follows. - vm.dirty_background_ratio - vm.dirty_ratio - + vm.dirty_background_ratio, vm.dirty_ratio These ratios apply the same to cgroup writeback with the amount of available memory capped by limits imposed by the memory controller and system-wide clean memory. - vm.dirty_background_bytes - vm.dirty_bytes - + vm.dirty_background_bytes, vm.dirty_bytes For cgroup writeback, this is calculated into ratio against total available memory and applied the same way as vm.dirty[_background]_ratio. -5-4. PID +PID +--- The process number controller is used to allow a cgroup to stop any new tasks from being fork()'d or clone()'d after a specified limit is @@ -1221,17 +1221,16 @@ Note that PIDs used in this controller refer to TIDs, process IDs as used by the kernel. -5-4-1. PID Interface Files +PID Interface Files +~~~~~~~~~~~~~~~~~~~ pids.max - A read-write single value file which exists on non-root cgroups. The default is "max". Hard limit of number of processes. pids.current - A read-only single value file which exists on all cgroups. The number of processes currently in the cgroup and its @@ -1246,12 +1245,14 @@ through fork() or clone(). These will return -EAGAIN if the creation of a new process would cause a cgroup policy to be violated. -5-5. RDMA +RDMA +---- The "rdma" controller regulates the distribution and accounting of of RDMA resources. -5-5-1. RDMA Interface Files +RDMA Interface Files +~~~~~~~~~~~~~~~~~~~~ rdma.max A readwrite nested-keyed file that exists for all the cgroups @@ -1264,10 +1265,12 @@ of RDMA resources. The following nested keys are defined. + ========== ============================= hca_handle Maximum number of HCA Handles hca_object Maximum number of HCA Objects + ========== ============================= - An example for mlx4 and ocrdma device follows. + An example for mlx4 and ocrdma device follows:: mlx4_0 hca_handle=2 hca_object=2000 ocrdma1 hca_handle=3 hca_object=max @@ -1276,15 +1279,17 @@ of RDMA resources. A read-only file that describes current resource usage. It exists for all the cgroup except root. - An example for mlx4 and ocrdma device follows. + An example for mlx4 and ocrdma device follows:: mlx4_0 hca_handle=1 hca_object=20 ocrdma1 hca_handle=1 hca_object=23 -5-6. Misc +Misc +---- -5-6-1. perf_event +perf_event +~~~~~~~~~~ perf_event controller, if not mounted on a legacy hierarchy, is automatically enabled on the v2 hierarchy so that perf events can @@ -1292,9 +1297,11 @@ always be filtered by cgroup v2 path. The controller can still be moved to a legacy hierarchy after v2 hierarchy is populated. -6. Namespace +Namespace +========= -6-1. Basics +Basics +------ cgroup namespace provides a mechanism to virtualize the view of the "/proc/$PID/cgroup" file and cgroup mounts. The CLONE_NEWCGROUP clone @@ -1308,7 +1315,7 @@ Without cgroup namespace, the "/proc/$PID/cgroup" file shows the complete path of the cgroup of a process. In a container setup where a set of cgroups and namespaces are intended to isolate processes the "/proc/$PID/cgroup" file may leak potential system level information -to the isolated processes. For Example: +to the isolated processes. For Example:: # cat /proc/self/cgroup 0::/batchjobs/container_id1 @@ -1316,14 +1323,14 @@ to the isolated processes. For Example: The path '/batchjobs/container_id1' can be considered as system-data and undesirable to expose to the isolated processes. cgroup namespace can be used to restrict visibility of this path. For example, before -creating a cgroup namespace, one would see: +creating a cgroup namespace, one would see:: # ls -l /proc/self/ns/cgroup lrwxrwxrwx 1 root root 0 2014-07-15 10:37 /proc/self/ns/cgroup -> cgroup:[4026531835] # cat /proc/self/cgroup 0::/batchjobs/container_id1 -After unsharing a new namespace, the view changes. +After unsharing a new namespace, the view changes:: # ls -l /proc/self/ns/cgroup lrwxrwxrwx 1 root root 0 2014-07-15 10:35 /proc/self/ns/cgroup -> cgroup:[4026532183] @@ -1341,7 +1348,8 @@ namespace is destroyed. The cgroupns root and the actual cgroups remain. -6-2. The Root and Views +The Root and Views +------------------ The 'cgroupns root' for a cgroup namespace is the cgroup in which the process calling unshare(2) is running. For example, if a process in @@ -1350,7 +1358,7 @@ process calling unshare(2) is running. For example, if a process in init_cgroup_ns, this is the real root ('/') cgroup. The cgroupns root cgroup does not change even if the namespace creator -process later moves to a different cgroup. +process later moves to a different cgroup:: # ~/unshare -c # unshare cgroupns in some cgroup # cat /proc/self/cgroup @@ -1364,7 +1372,7 @@ Each process gets its namespace-specific view of "/proc/$PID/cgroup" Processes running inside the cgroup namespace will be able to see cgroup paths (in /proc/self/cgroup) only inside their root cgroup. -From within an unshared cgroupns: +From within an unshared cgroupns:: # sleep 100000 & [1] 7353 @@ -1373,7 +1381,7 @@ From within an unshared cgroupns: 0::/sub_cgrp_1 From the initial cgroup namespace, the real cgroup path will be -visible: +visible:: $ cat /proc/7353/cgroup 0::/batchjobs/container_id1/sub_cgrp_1 @@ -1381,7 +1389,7 @@ visible: From a sibling cgroup namespace (that is, a namespace rooted at a different cgroup), the cgroup path relative to its own cgroup namespace root will be shown. For instance, if PID 7353's cgroup -namespace root is at '/batchjobs/container_id2', then it will see +namespace root is at '/batchjobs/container_id2', then it will see:: # cat /proc/7353/cgroup 0::/../container_id2/sub_cgrp_1 @@ -1390,13 +1398,14 @@ Note that the relative path always starts with '/' to indicate that its relative to the cgroup namespace root of the caller. -6-3. Migration and setns(2) +Migration and setns(2) +---------------------- Processes inside a cgroup namespace can move into and out of the namespace root if they have proper access to external cgroups. For example, from inside a namespace with cgroupns root at /batchjobs/container_id1, and assuming that the global hierarchy is -still accessible inside cgroupns: +still accessible inside cgroupns:: # cat /proc/7353/cgroup 0::/sub_cgrp_1 @@ -1418,10 +1427,11 @@ namespace. It is expected that the someone moves the attaching process under the target cgroup namespace root. -6-4. Interaction with Other Namespaces +Interaction with Other Namespaces +--------------------------------- Namespace specific cgroup hierarchy can be mounted by a process -running inside a non-init cgroup namespace. +running inside a non-init cgroup namespace:: # mount -t cgroup2 none $MOUNT_POINT @@ -1434,27 +1444,27 @@ the view of cgroup hierarchy by namespace-private cgroupfs mount provides a properly isolated cgroup view inside the container. -P. Information on Kernel Programming +Information on Kernel Programming +================================= This section contains kernel programming information in the areas where interacting with cgroup is necessary. cgroup core and controllers are not covered. -P-1. Filesystem Support for Writeback +Filesystem Support for Writeback +-------------------------------- A filesystem can support cgroup writeback by updating address_space_operations->writepage[s]() to annotate bio's using the following two functions. wbc_init_bio(@wbc, @bio) - Should be called for each bio carrying writeback data and associates the bio with the inode's owner cgroup. Can be called anytime between bio allocation and submission. wbc_account_io(@wbc, @page, @bytes) - Should be called for each data segment being written out. While this function doesn't care exactly when it's called during the writeback session, it's the easiest and most @@ -1475,7 +1485,8 @@ cases by skipping wbc_init_bio() or using bio_associate_blkcg() directly. -D. Deprecated v1 Core Features +Deprecated v1 Core Features +=========================== - Multiple hierarchies including named ones are not supported. @@ -1489,9 +1500,11 @@ D. Deprecated v1 Core Features at the root instead. -R. Issues with v1 and Rationales for v2 +Issues with v1 and Rationales for v2 +==================================== -R-1. Multiple Hierarchies +Multiple Hierarchies +-------------------- cgroup v1 allowed an arbitrary number of hierarchies and each hierarchy could host any number of controllers. While this seemed to @@ -1543,7 +1556,8 @@ how memory is distributed beyond a certain level while still wanting to control how CPU cycles are distributed. -R-2. Thread Granularity +Thread Granularity +------------------ cgroup v1 allowed threads of a process to belong to different cgroups. This didn't make sense for some controllers and those controllers @@ -1586,7 +1600,8 @@ misbehaving and poorly abstracted interfaces and kernel exposing and locked into constructs inadvertently. -R-3. Competition Between Inner Nodes and Threads +Competition Between Inner Nodes and Threads +------------------------------------------- cgroup v1 allowed threads to be in any cgroups which created an interesting problem where threads belonging to a parent cgroup and its @@ -1605,7 +1620,7 @@ simply weren't available for threads. The io controller implicitly created a hidden leaf node for each cgroup to host the threads. The hidden leaf had its own copies of all -the knobs with "leaf_" prefixed. While this allowed equivalent +the knobs with ``leaf_`` prefixed. While this allowed equivalent control over internal threads, it was with serious drawbacks. It always added an extra layer of nesting which wouldn't be necessary otherwise, made the interface messy and significantly complicated the @@ -1626,7 +1641,8 @@ This clearly is a problem which needs to be addressed from cgroup core in a uniform way. -R-4. Other Interface Issues +Other Interface Issues +---------------------- cgroup v1 grew without oversight and developed a large number of idiosyncrasies and inconsistencies. One issue on the cgroup core side @@ -1654,9 +1670,11 @@ cgroup v2 establishes common conventions where appropriate and updates controllers so that they expose minimal and consistent interfaces. -R-5. Controller Issues and Remedies +Controller Issues and Remedies +------------------------------ -R-5-1. Memory +Memory +~~~~~~ The original lower boundary, the soft limit, is defined as a limit that is per default unset. As a result, the set of cgroups that diff --git a/Documentation/circular-buffers.txt b/Documentation/circular-buffers.txt index 4a824d232472..d4628174b7c5 100644 --- a/Documentation/circular-buffers.txt +++ b/Documentation/circular-buffers.txt @@ -1,9 +1,9 @@ - ================ - CIRCULAR BUFFERS - ================ +================ +Circular Buffers +================ -By: David Howells <dhowells@redhat.com> - Paul E. McKenney <paulmck@linux.vnet.ibm.com> +:Author: David Howells <dhowells@redhat.com> +:Author: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Linux provides a number of features that can be used to implement circular @@ -20,7 +20,7 @@ producer and just one consumer. It is possible to handle multiple producers by serialising them, and to handle multiple consumers by serialising them. -Contents: +.. Contents: (*) What is a circular buffer? @@ -31,8 +31,8 @@ Contents: - The consumer. -========================== -WHAT IS A CIRCULAR BUFFER? + +What is a circular buffer? ========================== First of all, what is a circular buffer? A circular buffer is a buffer of @@ -60,9 +60,7 @@ buffer, provided that neither index overtakes the other. The implementer must be careful, however, as a region more than one unit in size may wrap the end of the buffer and be broken into two segments. - -============================ -MEASURING POWER-OF-2 BUFFERS +Measuring power-of-2 buffers ============================ Calculation of the occupancy or the remaining capacity of an arbitrarily sized @@ -71,13 +69,13 @@ modulus (divide) instruction. However, if the buffer is of a power-of-2 size, then a much quicker bitwise-AND instruction can be used instead. Linux provides a set of macros for handling power-of-2 circular buffers. These -can be made use of by: +can be made use of by:: #include <linux/circ_buf.h> The macros are: - (*) Measure the remaining capacity of a buffer: + (#) Measure the remaining capacity of a buffer:: CIRC_SPACE(head_index, tail_index, buffer_size); @@ -85,7 +83,7 @@ The macros are: can be inserted. - (*) Measure the maximum consecutive immediate space in a buffer: + (#) Measure the maximum consecutive immediate space in a buffer:: CIRC_SPACE_TO_END(head_index, tail_index, buffer_size); @@ -94,14 +92,14 @@ The macros are: beginning of the buffer. - (*) Measure the occupancy of a buffer: + (#) Measure the occupancy of a buffer:: CIRC_CNT(head_index, tail_index, buffer_size); This returns the number of items currently occupying a buffer[2]. - (*) Measure the non-wrapping occupancy of a buffer: + (#) Measure the non-wrapping occupancy of a buffer:: CIRC_CNT_TO_END(head_index, tail_index, buffer_size); @@ -112,7 +110,7 @@ The macros are: Each of these macros will nominally return a value between 0 and buffer_size-1, however: - [1] CIRC_SPACE*() are intended to be used in the producer. To the producer + (1) CIRC_SPACE*() are intended to be used in the producer. To the producer they will return a lower bound as the producer controls the head index, but the consumer may still be depleting the buffer on another CPU and moving the tail index. @@ -120,7 +118,7 @@ however: To the consumer it will show an upper bound as the producer may be busy depleting the space. - [2] CIRC_CNT*() are intended to be used in the consumer. To the consumer they + (2) CIRC_CNT*() are intended to be used in the consumer. To the consumer they will return a lower bound as the consumer controls the tail index, but the producer may still be filling the buffer on another CPU and moving the head index. @@ -128,14 +126,12 @@ however: To the producer it will show an upper bound as the consumer may be busy emptying the buffer. - [3] To a third party, the order in which the writes to the indices by the + (3) To a third party, the order in which the writes to the indices by the producer and consumer become visible cannot be guaranteed as they are independent and may be made on different CPUs - so the result in such a situation will merely be a guess, and may even be negative. - -=========================================== -USING MEMORY BARRIERS WITH CIRCULAR BUFFERS +Using memory barriers with circular buffers =========================================== By using memory barriers in conjunction with circular buffers, you can avoid @@ -152,10 +148,10 @@ time, and only one thing should be emptying a buffer at any one time, but the two sides can operate simultaneously. -THE PRODUCER +The producer ------------ -The producer will look something like this: +The producer will look something like this:: spin_lock(&producer_lock); @@ -193,10 +189,10 @@ ordering between the read of the index indicating that the consumer has vacated a given element and the write by the producer to that same element. -THE CONSUMER +The Consumer ------------ -The consumer will look something like this: +The consumer will look something like this:: spin_lock(&consumer_lock); @@ -235,8 +231,7 @@ prevents the compiler from tearing the store, and enforces ordering against previous accesses. -=============== -FURTHER READING +Further reading =============== See also Documentation/memory-barriers.txt for a description of Linux's memory diff --git a/Documentation/clk.txt b/Documentation/clk.txt index 22f026aa2f34..be909ed45970 100644 --- a/Documentation/clk.txt +++ b/Documentation/clk.txt @@ -1,12 +1,16 @@ - The Common Clk Framework - Mike Turquette <mturquette@ti.com> +======================== +The Common Clk Framework +======================== + +:Author: Mike Turquette <mturquette@ti.com> This document endeavours to explain the common clk framework details, and how to port a platform over to this framework. It is not yet a detailed explanation of the clock api in include/linux/clk.h, but perhaps someday it will include that information. - Part 1 - introduction and interface split +Introduction and interface split +================================ The common clk framework is an interface to control the clock nodes available on various devices today. This may come in the form of clock @@ -35,10 +39,11 @@ is defined in struct clk_foo and pointed to within struct clk_core. This allows for easy navigation between the two discrete halves of the common clock interface. - Part 2 - common data structures and api +Common data structures and api +============================== Below is the common struct clk_core definition from -drivers/clk/clk.c, modified for brevity: +drivers/clk/clk.c, modified for brevity:: struct clk_core { const char *name; @@ -59,7 +64,7 @@ struct clk. That api is documented in include/linux/clk.h. Platforms and devices utilizing the common struct clk_core use the struct clk_ops pointer in struct clk_core to perform the hardware-specific parts of -the operations defined in clk-provider.h: +the operations defined in clk-provider.h:: struct clk_ops { int (*prepare)(struct clk_hw *hw); @@ -95,19 +100,20 @@ the operations defined in clk-provider.h: struct dentry *dentry); }; - Part 3 - hardware clk implementations +Hardware clk implementations +============================ The strength of the common struct clk_core comes from its .ops and .hw pointers which abstract the details of struct clk from the hardware-specific bits, and vice versa. To illustrate consider the simple gateable clk implementation in -drivers/clk/clk-gate.c: +drivers/clk/clk-gate.c:: -struct clk_gate { - struct clk_hw hw; - void __iomem *reg; - u8 bit_idx; - ... -}; + struct clk_gate { + struct clk_hw hw; + void __iomem *reg; + u8 bit_idx; + ... + }; struct clk_gate contains struct clk_hw hw as well as hardware-specific knowledge about which register and bit controls this clk's gating. @@ -115,7 +121,7 @@ Nothing about clock topology or accounting, such as enable_count or notifier_count, is needed here. That is all handled by the common framework code and struct clk_core. -Let's walk through enabling this clk from driver code: +Let's walk through enabling this clk from driver code:: struct clk *clk; clk = clk_get(NULL, "my_gateable_clk"); @@ -123,70 +129,71 @@ Let's walk through enabling this clk from driver code: clk_prepare(clk); clk_enable(clk); -The call graph for clk_enable is very simple: +The call graph for clk_enable is very simple:: -clk_enable(clk); - clk->ops->enable(clk->hw); - [resolves to...] - clk_gate_enable(hw); - [resolves struct clk gate with to_clk_gate(hw)] - clk_gate_set_bit(gate); + clk_enable(clk); + clk->ops->enable(clk->hw); + [resolves to...] + clk_gate_enable(hw); + [resolves struct clk gate with to_clk_gate(hw)] + clk_gate_set_bit(gate); -And the definition of clk_gate_set_bit: +And the definition of clk_gate_set_bit:: -static void clk_gate_set_bit(struct clk_gate *gate) -{ - u32 reg; + static void clk_gate_set_bit(struct clk_gate *gate) + { + u32 reg; - reg = __raw_readl(gate->reg); - reg |= BIT(gate->bit_idx); - writel(reg, gate->reg); -} + reg = __raw_readl(gate->reg); + reg |= BIT(gate->bit_idx); + writel(reg, gate->reg); + } -Note that to_clk_gate is defined as: +Note that to_clk_gate is defined as:: -#define to_clk_gate(_hw) container_of(_hw, struct clk_gate, hw) + #define to_clk_gate(_hw) container_of(_hw, struct clk_gate, hw) This pattern of abstraction is used for every clock hardware representation. - Part 4 - supporting your own clk hardware +Supporting your own clk hardware +================================ When implementing support for a new type of clock it is only necessary to -include the following header: +include the following header:: -#include <linux/clk-provider.h> + #include <linux/clk-provider.h> To construct a clk hardware structure for your platform you must define -the following: +the following:: -struct clk_foo { - struct clk_hw hw; - ... hardware specific data goes here ... -}; + struct clk_foo { + struct clk_hw hw; + ... hardware specific data goes here ... + }; To take advantage of your data you'll need to support valid operations -for your clk: +for your clk:: -struct clk_ops clk_foo_ops { - .enable = &clk_foo_enable; - .disable = &clk_foo_disable; -}; + struct clk_ops clk_foo_ops { + .enable = &clk_foo_enable; + .disable = &clk_foo_disable; + }; -Implement the above functions using container_of: +Implement the above functions using container_of:: -#define to_clk_foo(_hw) container_of(_hw, struct clk_foo, hw) + #define to_clk_foo(_hw) container_of(_hw, struct clk_foo, hw) -int clk_foo_enable(struct clk_hw *hw) -{ - struct clk_foo *foo; + int clk_foo_enable(struct clk_hw *hw) + { + struct clk_foo *foo; - foo = to_clk_foo(hw); + foo = to_clk_foo(hw); - ... perform magic on foo ... + ... perform magic on foo ... - return 0; -}; + return 0; + }; Below is a matrix detailing which clk_ops are mandatory based upon the hardware capabilities of that clock. A cell marked as "y" means @@ -194,41 +201,56 @@ mandatory, a cell marked as "n" implies that either including that callback is invalid or otherwise unnecessary. Empty cells are either optional or must be evaluated on a case-by-case basis. - clock hardware characteristics - ----------------------------------------------------------- - | gate | change rate | single parent | multiplexer | root | - |------|-------------|---------------|-------------|------| -.prepare | | | | | | -.unprepare | | | | | | - | | | | | | -.enable | y | | | | | -.disable | y | | | | | -.is_enabled | y | | | | | - | | | | | | -.recalc_rate | | y | | | | -.round_rate | | y [1] | | | | -.determine_rate | | y [1] | | | | -.set_rate | | y | | | | - | | | | | | -.set_parent | | | n | y | n | -.get_parent | | | n | y | n | - | | | | | | -.recalc_accuracy| | | | | | - | | | | | | -.init | | | | | | - ----------------------------------------------------------- -[1] either one of round_rate or determine_rate is required. +.. table:: clock hardware characteristics + + +----------------+------+-------------+---------------+-------------+------+ + | | gate | change rate | single parent | multiplexer | root | + +================+======+=============+===============+=============+======+ + |.prepare | | | | | | + +----------------+------+-------------+---------------+-------------+------+ + |.unprepare | | | | | | + +----------------+------+-------------+---------------+-------------+------+ + +----------------+------+-------------+---------------+-------------+------+ + |.enable | y | | | | | + +----------------+------+-------------+---------------+-------------+------+ + |.disable | y | | | | | + +----------------+------+-------------+---------------+-------------+------+ + |.is_enabled | y | | | | | + +----------------+------+-------------+---------------+-------------+------+ + +----------------+------+-------------+---------------+-------------+------+ + |.recalc_rate | | y | | | | + +----------------+------+-------------+---------------+-------------+------+ + |.round_rate | | y [1]_ | | | | + +----------------+------+-------------+---------------+-------------+------+ + |.determine_rate | | y [1]_ | | | | + +----------------+------+-------------+---------------+-------------+------+ + |.set_rate | | y | | | | + +----------------+------+-------------+---------------+-------------+------+ + +----------------+------+-------------+---------------+-------------+------+ + |.set_parent | | | n | y | n | + +----------------+------+-------------+---------------+-------------+------+ + |.get_parent | | | n | y | n | + +----------------+------+-------------+---------------+-------------+------+ + +----------------+------+-------------+---------------+-------------+------+ + |.recalc_accuracy| | | | | | + +----------------+------+-------------+---------------+-------------+------+ + +----------------+------+-------------+---------------+-------------+------+ + |.init | | | | | | + +----------------+------+-------------+---------------+-------------+------+ + +.. [1] either one of round_rate or determine_rate is required. Finally, register your clock at run-time with a hardware-specific registration function. This function simply populates struct clk_foo's data and then passes the common struct clk parameters to the framework -with a call to: +with a call to:: -clk_register(...) + clk_register(...) -See the basic clock types in drivers/clk/clk-*.c for examples. +See the basic clock types in ``drivers/clk/clk-*.c`` for examples. - Part 5 - Disabling clock gating of unused clocks +Disabling clock gating of unused clocks +======================================= Sometimes during development it can be useful to be able to bypass the default disabling of unused clocks. For example, if drivers aren't enabling @@ -239,7 +261,8 @@ are sorted out. To bypass this disabling, include "clk_ignore_unused" in the bootargs to the kernel. - Part 6 - Locking +Locking +======= The common clock framework uses two global locks, the prepare lock and the enable lock. diff --git a/Documentation/core-api/kernel-api.rst b/Documentation/core-api/kernel-api.rst index 9ec8488319dc..17b00914c6ab 100644 --- a/Documentation/core-api/kernel-api.rst +++ b/Documentation/core-api/kernel-api.rst @@ -114,7 +114,7 @@ The Slab Cache User Space Memory Access ------------------------ -.. kernel-doc:: arch/x86/include/asm/uaccess_32.h +.. kernel-doc:: arch/x86/include/asm/uaccess.h :internal: .. kernel-doc:: arch/x86/lib/usercopy_32.c diff --git a/Documentation/cpu-load.txt b/Documentation/cpu-load.txt index 287224e57cfc..2d01ce43d2a2 100644 --- a/Documentation/cpu-load.txt +++ b/Documentation/cpu-load.txt @@ -1,9 +1,10 @@ +======== CPU load --------- +======== -Linux exports various bits of information via `/proc/stat' and -`/proc/uptime' that userland tools, such as top(1), use to calculate -the average time system spent in a particular state, for example: +Linux exports various bits of information via ``/proc/stat`` and +``/proc/uptime`` that userland tools, such as top(1), use to calculate +the average time system spent in a particular state, for example:: $ iostat Linux 2.6.18.3-exp (linmac) 02/20/2007 @@ -17,7 +18,7 @@ Here the system thinks that over the default sampling period the system spent 10.01% of the time doing work in user space, 2.92% in the kernel, and was overall 81.63% of the time idle. -In most cases the `/proc/stat' information reflects the reality quite +In most cases the ``/proc/stat`` information reflects the reality quite closely, however due to the nature of how/when the kernel collects this data sometimes it can not be trusted at all. @@ -33,78 +34,78 @@ Example ------- If we imagine the system with one task that periodically burns cycles -in the following manner: +in the following manner:: - time line between two timer interrupts -|--------------------------------------| - ^ ^ - |_ something begins working | - |_ something goes to sleep - (only to be awaken quite soon) + time line between two timer interrupts + |--------------------------------------| + ^ ^ + |_ something begins working | + |_ something goes to sleep + (only to be awaken quite soon) In the above situation the system will be 0% loaded according to the -`/proc/stat' (since the timer interrupt will always happen when the +``/proc/stat`` (since the timer interrupt will always happen when the system is executing the idle handler), but in reality the load is closer to 99%. One can imagine many more situations where this behavior of the kernel -will lead to quite erratic information inside `/proc/stat'. - - -/* gcc -o hog smallhog.c */ -#include <time.h> -#include <limits.h> -#include <signal.h> -#include <sys/time.h> -#define HIST 10 - -static volatile sig_atomic_t stop; - -static void sighandler (int signr) -{ - (void) signr; - stop = 1; -} -static unsigned long hog (unsigned long niters) -{ - stop = 0; - while (!stop && --niters); - return niters; -} -int main (void) -{ - int i; - struct itimerval it = { .it_interval = { .tv_sec = 0, .tv_usec = 1 }, - .it_value = { .tv_sec = 0, .tv_usec = 1 } }; - sigset_t set; - unsigned long v[HIST]; - double tmp = 0.0; - unsigned long n; - signal (SIGALRM, &sighandler); - setitimer (ITIMER_REAL, &it, NULL); - - hog (ULONG_MAX); - for (i = 0; i < HIST; ++i) v[i] = ULONG_MAX - hog (ULONG_MAX); - for (i = 0; i < HIST; ++i) tmp += v[i]; - tmp /= HIST; - n = tmp - (tmp / 3.0); - - sigemptyset (&set); - sigaddset (&set, SIGALRM); - - for (;;) { - hog (n); - sigwait (&set, &i); - } - return 0; -} +will lead to quite erratic information inside ``/proc/stat``:: + + + /* gcc -o hog smallhog.c */ + #include <time.h> + #include <limits.h> + #include <signal.h> + #include <sys/time.h> + #define HIST 10 + + static volatile sig_atomic_t stop; + + static void sighandler (int signr) + { + (void) signr; + stop = 1; + } + static unsigned long hog (unsigned long niters) + { + stop = 0; + while (!stop && --niters); + return niters; + } + int main (void) + { + int i; + struct itimerval it = { .it_interval = { .tv_sec = 0, .tv_usec = 1 }, + .it_value = { .tv_sec = 0, .tv_usec = 1 } }; + sigset_t set; + unsigned long v[HIST]; + double tmp = 0.0; + unsigned long n; + signal (SIGALRM, &sighandler); + setitimer (ITIMER_REAL, &it, NULL); + + hog (ULONG_MAX); + for (i = 0; i < HIST; ++i) v[i] = ULONG_MAX - hog (ULONG_MAX); + for (i = 0; i < HIST; ++i) tmp += v[i]; + tmp /= HIST; + n = tmp - (tmp / 3.0); + + sigemptyset (&set); + sigaddset (&set, SIGALRM); + + for (;;) { + hog (n); + sigwait (&set, &i); + } + return 0; + } References ---------- -http://lkml.org/lkml/2007/2/12/6 -Documentation/filesystems/proc.txt (1.8) +- http://lkml.org/lkml/2007/2/12/6 +- Documentation/filesystems/proc.txt (1.8) Thanks diff --git a/Documentation/cputopology.txt b/Documentation/cputopology.txt index 127c9d8c2174..c6e7e9196a8b 100644 --- a/Documentation/cputopology.txt +++ b/Documentation/cputopology.txt @@ -1,3 +1,6 @@ +=========================================== +How CPU topology info is exported via sysfs +=========================================== Export CPU topology info via sysfs. Items (attributes) are similar to /proc/cpuinfo output of some architectures: @@ -75,24 +78,26 @@ CONFIG_SCHED_BOOK and CONFIG_DRAWER are currently only used on s390, where they reflect the cpu and cache hierarchy. For an architecture to support this feature, it must define some of -these macros in include/asm-XXX/topology.h: -#define topology_physical_package_id(cpu) -#define topology_core_id(cpu) -#define topology_book_id(cpu) -#define topology_drawer_id(cpu) -#define topology_sibling_cpumask(cpu) -#define topology_core_cpumask(cpu) -#define topology_book_cpumask(cpu) -#define topology_drawer_cpumask(cpu) - -The type of **_id macros is int. -The type of **_cpumask macros is (const) struct cpumask *. The latter -correspond with appropriate **_siblings sysfs attributes (except for +these macros in include/asm-XXX/topology.h:: + + #define topology_physical_package_id(cpu) + #define topology_core_id(cpu) + #define topology_book_id(cpu) + #define topology_drawer_id(cpu) + #define topology_sibling_cpumask(cpu) + #define topology_core_cpumask(cpu) + #define topology_book_cpumask(cpu) + #define topology_drawer_cpumask(cpu) + +The type of ``**_id macros`` is int. +The type of ``**_cpumask macros`` is ``(const) struct cpumask *``. The latter +correspond with appropriate ``**_siblings`` sysfs attributes (except for topology_sibling_cpumask() which corresponds with thread_siblings). To be consistent on all architectures, include/linux/topology.h provides default definitions for any of the above macros that are not defined by include/asm-XXX/topology.h: + 1) physical_package_id: -1 2) core_id: 0 3) sibling_cpumask: just the given CPU @@ -107,6 +112,7 @@ Additionally, CPU topology information is provided under /sys/devices/system/cpu and includes these files. The internal source for the output is in brackets ("[]"). + =========== ========================================================== kernel_max: the maximum CPU index allowed by the kernel configuration. [NR_CPUS-1] @@ -122,6 +128,7 @@ source for the output is in brackets ("[]"). present: CPUs that have been identified as being present in the system. [cpu_present_mask] + =========== ========================================================== The format for the above output is compatible with cpulist_parse() [see <linux/cpumask.h>]. Some examples follow. @@ -129,7 +136,7 @@ The format for the above output is compatible with cpulist_parse() In this example, there are 64 CPUs in the system but cpus 32-63 exceed the kernel max which is limited to 0..31 by the NR_CPUS config option being 32. Note also that CPUs 2 and 4-31 are not online but could be -brought online as they are both present and possible. +brought online as they are both present and possible:: kernel_max: 31 offline: 2,4-31,32-63 @@ -140,7 +147,7 @@ brought online as they are both present and possible. In this example, the NR_CPUS config option is 128, but the kernel was started with possible_cpus=144. There are 4 CPUs in the system and cpu2 was manually taken offline (and is the only CPU that can be brought -online.) +online.):: kernel_max: 127 offline: 2,4-127,128-143 diff --git a/Documentation/crc32.txt b/Documentation/crc32.txt index a08a7dd9d625..8a6860f33b4e 100644 --- a/Documentation/crc32.txt +++ b/Documentation/crc32.txt @@ -1,4 +1,6 @@ -A brief CRC tutorial. +================================= +brief tutorial on CRC computation +================================= A CRC is a long-division remainder. You add the CRC to the message, and the whole thing (message+CRC) is a multiple of the given @@ -8,7 +10,8 @@ remainder computed on the message+CRC is 0. This latter approach is used by a lot of hardware implementations, and is why so many protocols put the end-of-frame flag after the CRC. -It's actually the same long division you learned in school, except that +It's actually the same long division you learned in school, except that: + - We're working in binary, so the digits are only 0 and 1, and - When dividing polynomials, there are no carries. Rather than add and subtract, we just xor. Thus, we tend to get a bit sloppy about @@ -40,11 +43,12 @@ throw the quotient bit away, but subtract the appropriate multiple of the polynomial from the remainder and we're back to where we started, ready to process the next bit. -A big-endian CRC written this way would be coded like: -for (i = 0; i < input_bits; i++) { - multiple = remainder & 0x80000000 ? CRCPOLY : 0; - remainder = (remainder << 1 | next_input_bit()) ^ multiple; -} +A big-endian CRC written this way would be coded like:: + + for (i = 0; i < input_bits; i++) { + multiple = remainder & 0x80000000 ? CRCPOLY : 0; + remainder = (remainder << 1 | next_input_bit()) ^ multiple; + } Notice how, to get at bit 32 of the shifted remainder, we look at bit 31 of the remainder *before* shifting it. @@ -54,25 +58,26 @@ the remainder don't actually affect any decision-making until 32 bits later. Thus, the first 32 cycles of this are pretty boring. Also, to add the CRC to a message, we need a 32-bit-long hole for it at the end, so we have to add 32 extra cycles shifting in zeros at the -end of every message, +end of every message. These details lead to a standard trick: rearrange merging in the next_input_bit() until the moment it's needed. Then the first 32 cycles can be precomputed, and merging in the final 32 zero bits to make room -for the CRC can be skipped entirely. This changes the code to: +for the CRC can be skipped entirely. This changes the code to:: -for (i = 0; i < input_bits; i++) { - remainder ^= next_input_bit() << 31; - multiple = (remainder & 0x80000000) ? CRCPOLY : 0; - remainder = (remainder << 1) ^ multiple; -} + for (i = 0; i < input_bits; i++) { + remainder ^= next_input_bit() << 31; + multiple = (remainder & 0x80000000) ? CRCPOLY : 0; + remainder = (remainder << 1) ^ multiple; + } -With this optimization, the little-endian code is particularly simple: -for (i = 0; i < input_bits; i++) { - remainder ^= next_input_bit(); - multiple = (remainder & 1) ? CRCPOLY : 0; - remainder = (remainder >> 1) ^ multiple; -} +With this optimization, the little-endian code is particularly simple:: + + for (i = 0; i < input_bits; i++) { + remainder ^= next_input_bit(); + multiple = (remainder & 1) ? CRCPOLY : 0; + remainder = (remainder >> 1) ^ multiple; + } The most significant coefficient of the remainder polynomial is stored in the least significant bit of the binary "remainder" variable. @@ -81,23 +86,25 @@ be bit-reversed) and next_input_bit(). As long as next_input_bit is returning the bits in a sensible order, we don't *have* to wait until the last possible moment to merge in additional bits. -We can do it 8 bits at a time rather than 1 bit at a time: -for (i = 0; i < input_bytes; i++) { - remainder ^= next_input_byte() << 24; - for (j = 0; j < 8; j++) { - multiple = (remainder & 0x80000000) ? CRCPOLY : 0; - remainder = (remainder << 1) ^ multiple; +We can do it 8 bits at a time rather than 1 bit at a time:: + + for (i = 0; i < input_bytes; i++) { + remainder ^= next_input_byte() << 24; + for (j = 0; j < 8; j++) { + multiple = (remainder & 0x80000000) ? CRCPOLY : 0; + remainder = (remainder << 1) ^ multiple; + } } -} -Or in little-endian: -for (i = 0; i < input_bytes; i++) { - remainder ^= next_input_byte(); - for (j = 0; j < 8; j++) { - multiple = (remainder & 1) ? CRCPOLY : 0; - remainder = (remainder >> 1) ^ multiple; +Or in little-endian:: + + for (i = 0; i < input_bytes; i++) { + remainder ^= next_input_byte(); + for (j = 0; j < 8; j++) { + multiple = (remainder & 1) ? CRCPOLY : 0; + remainder = (remainder >> 1) ^ multiple; + } } -} If the input is a multiple of 32 bits, you can even XOR in a 32-bit word at a time and increase the inner loop count to 32. diff --git a/Documentation/crypto/asymmetric-keys.txt b/Documentation/crypto/asymmetric-keys.txt index b82b6ad48488..5969bf42562a 100644 --- a/Documentation/crypto/asymmetric-keys.txt +++ b/Documentation/crypto/asymmetric-keys.txt @@ -10,6 +10,7 @@ Contents: - Signature verification. - Asymmetric key subtypes. - Instantiation data parsers. + - Keyring link restrictions. ======== @@ -318,7 +319,8 @@ KEYRING LINK RESTRICTIONS ========================= Keyrings created from userspace using add_key can be configured to check the -signature of the key being linked. +signature of the key being linked. Keys without a valid signature are not +allowed to link. Several restriction methods are available: @@ -327,9 +329,10 @@ Several restriction methods are available: - Option string used with KEYCTL_RESTRICT_KEYRING: - "builtin_trusted" - The kernel builtin trusted keyring will be searched for the signing - key. The ca_keys kernel parameter also affects which keys are used for - signature verification. + The kernel builtin trusted keyring will be searched for the signing key. + If the builtin trusted keyring is not configured, all links will be + rejected. The ca_keys kernel parameter also affects which keys are used + for signature verification. (2) Restrict using the kernel builtin and secondary trusted keyrings @@ -337,8 +340,10 @@ Several restriction methods are available: - "builtin_and_secondary_trusted" The kernel builtin and secondary trusted keyrings will be searched for the - signing key. The ca_keys kernel parameter also affects which keys are used - for signature verification. + signing key. If the secondary trusted keyring is not configured, this + restriction will behave like the "builtin_trusted" option. The ca_keys + kernel parameter also affects which keys are used for signature + verification. (3) Restrict using a separate key or keyring @@ -346,7 +351,7 @@ Several restriction methods are available: - "key_or_keyring:<key or keyring serial number>[:chain]" Whenever a key link is requested, the link will only succeed if the key - being linked is signed by one of the designated keys. This key may be + being linked is signed by one of the designated keys. This key may be specified directly by providing a serial number for one asymmetric key, or a group of keys may be searched for the signing key by providing the serial number for a keyring. @@ -354,7 +359,51 @@ Several restriction methods are available: When the "chain" option is provided at the end of the string, the keys within the destination keyring will also be searched for signing keys. This allows for verification of certificate chains by adding each - cert in order (starting closest to the root) to one keyring. + certificate in order (starting closest to the root) to a keyring. For + instance, one keyring can be populated with links to a set of root + certificates, with a separate, restricted keyring set up for each + certificate chain to be validated: + + # Create and populate a keyring for root certificates + root_id=`keyctl add keyring root-certs "" @s` + keyctl padd asymmetric "" $root_id < root1.cert + keyctl padd asymmetric "" $root_id < root2.cert + + # Create and restrict a keyring for the certificate chain + chain_id=`keyctl add keyring chain "" @s` + keyctl restrict_keyring $chain_id asymmetric key_or_keyring:$root_id:chain + + # Attempt to add each certificate in the chain, starting with the + # certificate closest to the root. + keyctl padd asymmetric "" $chain_id < intermediateA.cert + keyctl padd asymmetric "" $chain_id < intermediateB.cert + keyctl padd asymmetric "" $chain_id < end-entity.cert + + If the final end-entity certificate is successfully added to the "chain" + keyring, we can be certain that it has a valid signing chain going back to + one of the root certificates. + + A single keyring can be used to verify a chain of signatures by + restricting the keyring after linking the root certificate: + + # Create a keyring for the certificate chain and add the root + chain2_id=`keyctl add keyring chain2 "" @s` + keyctl padd asymmetric "" $chain2_id < root1.cert + + # Restrict the keyring that already has root1.cert linked. The cert + # will remain linked by the keyring. + keyctl restrict_keyring $chain2_id asymmetric key_or_keyring:0:chain + + # Attempt to add each certificate in the chain, starting with the + # certificate closest to the root. + keyctl padd asymmetric "" $chain2_id < intermediateA.cert + keyctl padd asymmetric "" $chain2_id < intermediateB.cert + keyctl padd asymmetric "" $chain2_id < end-entity.cert + + If the final end-entity certificate is successfully added to the "chain2" + keyring, we can be certain that there is a valid signing chain going back + to the root certificate that was added before the keyring was restricted. + In all of these cases, if the signing key is found the signature of the key to be linked will be verified using the signing key. The requested key is added diff --git a/Documentation/dcdbas.txt b/Documentation/dcdbas.txt index e1c52e2dc361..309cc57a7c1c 100644 --- a/Documentation/dcdbas.txt +++ b/Documentation/dcdbas.txt @@ -1,4 +1,9 @@ +=================================== +Dell Systems Management Base Driver +=================================== + Overview +======== The Dell Systems Management Base Driver provides a sysfs interface for systems management software such as Dell OpenManage to perform system @@ -17,6 +22,7 @@ more information about the libsmbios project. System Management Interrupt +=========================== On some Dell systems, systems management software must access certain management information via a system management interrupt (SMI). The SMI data @@ -24,12 +30,12 @@ buffer must reside in 32-bit address space, and the physical address of the buffer is required for the SMI. The driver maintains the memory required for the SMI and provides a way for the application to generate the SMI. The driver creates the following sysfs entries for systems management -software to perform these system management interrupts: +software to perform these system management interrupts:: -/sys/devices/platform/dcdbas/smi_data -/sys/devices/platform/dcdbas/smi_data_buf_phys_addr -/sys/devices/platform/dcdbas/smi_data_buf_size -/sys/devices/platform/dcdbas/smi_request + /sys/devices/platform/dcdbas/smi_data + /sys/devices/platform/dcdbas/smi_data_buf_phys_addr + /sys/devices/platform/dcdbas/smi_data_buf_size + /sys/devices/platform/dcdbas/smi_request Systems management software must perform the following steps to execute a SMI using this driver: @@ -43,6 +49,7 @@ a SMI using this driver: Host Control Action +=================== Dell OpenManage supports a host control feature that allows the administrator to perform a power cycle or power off of the system after the OS has finished @@ -69,12 +76,14 @@ power off host control action using this driver: Host Control SMI Type +===================== The following table shows the value to write to host_control_smi_type to perform a power cycle or power off host control action: +=================== ===================== PowerEdge System Host Control SMI Type ----------------- --------------------- +=================== ===================== 300 HC_SMITYPE_TYPE1 1300 HC_SMITYPE_TYPE1 1400 HC_SMITYPE_TYPE2 @@ -87,5 +96,4 @@ PowerEdge System Host Control SMI Type 1655MC HC_SMITYPE_TYPE2 700 HC_SMITYPE_TYPE3 750 HC_SMITYPE_TYPE3 - - +=================== ===================== diff --git a/Documentation/debugging-via-ohci1394.txt b/Documentation/debugging-via-ohci1394.txt index 9ff026d22b75..981ad4f89fd3 100644 --- a/Documentation/debugging-via-ohci1394.txt +++ b/Documentation/debugging-via-ohci1394.txt @@ -1,6 +1,6 @@ - - Using physical DMA provided by OHCI-1394 FireWire controllers for debugging - --------------------------------------------------------------------------- +=========================================================================== +Using physical DMA provided by OHCI-1394 FireWire controllers for debugging +=========================================================================== Introduction ------------ @@ -91,10 +91,10 @@ Step-by-step instructions for using firescope with early OHCI initialization: 1) Verify that your hardware is supported: Load the firewire-ohci module and check your kernel logs. - You should see a line similar to + You should see a line similar to:: - firewire_ohci 0000:15:00.1: added OHCI v1.0 device as card 2, 4 IR + 4 IT - ... contexts, quirks 0x11 + firewire_ohci 0000:15:00.1: added OHCI v1.0 device as card 2, 4 IR + 4 IT + ... contexts, quirks 0x11 when loading the driver. If you have no supported controller, many PCI, CardBus and even some Express cards which are fully compliant to OHCI-1394 @@ -113,9 +113,9 @@ Step-by-step instructions for using firescope with early OHCI initialization: stable connection and has matching connectors (there are small 4-pin and large 6-pin FireWire ports) will do. - If an driver is running on both machines you should see a line like + If an driver is running on both machines you should see a line like:: - firewire_core 0000:15:00.1: created device fw1: GUID 00061b0020105917, S400 + firewire_core 0000:15:00.1: created device fw1: GUID 00061b0020105917, S400 on both machines in the kernel log when the cable is plugged in and connects the two machines. @@ -123,7 +123,7 @@ Step-by-step instructions for using firescope with early OHCI initialization: 3) Test physical DMA using firescope: On the debug host, make sure that /dev/fw* is accessible, - then start firescope: + then start firescope:: $ firescope Port 0 (/dev/fw1) opened, 2 nodes detected @@ -163,7 +163,7 @@ Step-by-step instructions for using firescope with early OHCI initialization: host loaded, reboot the debugged machine, booting the kernel which has CONFIG_PROVIDE_OHCI1394_DMA_INIT enabled, with the option ohci1394_dma=early. - Then, on the debugging host, run firescope, for example by using -A: + Then, on the debugging host, run firescope, for example by using -A:: firescope -A System.map-of-debug-target-kernel @@ -178,6 +178,7 @@ Step-by-step instructions for using firescope with early OHCI initialization: Notes ----- + Documentation and specifications: http://halobates.de/firewire/ FireWire is a trademark of Apple Inc. - for more information please refer to: diff --git a/Documentation/dell_rbu.txt b/Documentation/dell_rbu.txt index d262e22bddec..0fdb6aa2704c 100644 --- a/Documentation/dell_rbu.txt +++ b/Documentation/dell_rbu.txt @@ -1,18 +1,30 @@ -Purpose: -Demonstrate the usage of the new open sourced rbu (Remote BIOS Update) driver +============================================================= +Usage of the new open sourced rbu (Remote BIOS Update) driver +============================================================= + +Purpose +======= + +Document demonstrating the use of the Dell Remote BIOS Update driver. for updating BIOS images on Dell servers and desktops. -Scope: +Scope +===== + This document discusses the functionality of the rbu driver only. It does not cover the support needed from applications to enable the BIOS to update itself with the image downloaded in to the memory. -Overview: +Overview +======== + This driver works with Dell OpenManage or Dell Update Packages for updating the BIOS on Dell servers (starting from servers sold since 1999), desktops and notebooks (starting from those sold in 2005). + Please go to http://support.dell.com register and you can find info on OpenManage and Dell Update packages (DUP). + Libsmbios can also be used to update BIOS on Dell systems go to http://linux.dell.com/libsmbios/ for details. @@ -22,6 +34,7 @@ of physical pages having the BIOS image. In case of packetized the app using the driver breaks the image in to packets of fixed sizes and the driver would place each packet in contiguous physical memory. The driver also maintains a link list of packets for reading them back. + If the dell_rbu driver is unloaded all the allocated memory is freed. The rbu driver needs to have an application (as mentioned above)which will @@ -30,28 +43,33 @@ inform the BIOS to enable the update in the next system reboot. The user should not unload the rbu driver after downloading the BIOS image or updating. -The driver load creates the following directories under the /sys file system. -/sys/class/firmware/dell_rbu/loading -/sys/class/firmware/dell_rbu/data -/sys/devices/platform/dell_rbu/image_type -/sys/devices/platform/dell_rbu/data -/sys/devices/platform/dell_rbu/packet_size +The driver load creates the following directories under the /sys file system:: + + /sys/class/firmware/dell_rbu/loading + /sys/class/firmware/dell_rbu/data + /sys/devices/platform/dell_rbu/image_type + /sys/devices/platform/dell_rbu/data + /sys/devices/platform/dell_rbu/packet_size The driver supports two types of update mechanism; monolithic and packetized. These update mechanism depends upon the BIOS currently running on the system. Most of the Dell systems support a monolithic update where the BIOS image is copied to a single contiguous block of physical memory. + In case of packet mechanism the single memory can be broken in smaller chunks of contiguous memory and the BIOS image is scattered in these packets. By default the driver uses monolithic memory for the update type. This can be changed to packets during the driver load time by specifying the load -parameter image_type=packet. This can also be changed later as below -echo packet > /sys/devices/platform/dell_rbu/image_type +parameter image_type=packet. This can also be changed later as below:: + + echo packet > /sys/devices/platform/dell_rbu/image_type In packet update mode the packet size has to be given before any packets can -be downloaded. It is done as below -echo XXXX > /sys/devices/platform/dell_rbu/packet_size +be downloaded. It is done as below:: + + echo XXXX > /sys/devices/platform/dell_rbu/packet_size + In the packet update mechanism, the user needs to create a new file having packets of data arranged back to back. It can be done as follows The user creates packets header, gets the chunk of the BIOS image and @@ -60,41 +78,54 @@ added together should match the specified packet_size. This makes one packet, the user needs to create more such packets out of the entire BIOS image file and then arrange all these packets back to back in to one single file. + This file is then copied to /sys/class/firmware/dell_rbu/data. Once this file gets to the driver, the driver extracts packet_size data from the file and spreads it across the physical memory in contiguous packet_sized space. + This method makes sure that all the packets get to the driver in a single operation. In monolithic update the user simply get the BIOS image (.hdr file) and copies to the data file as is without any change to the BIOS image itself. Do the steps below to download the BIOS image. + 1) echo 1 > /sys/class/firmware/dell_rbu/loading 2) cp bios_image.hdr /sys/class/firmware/dell_rbu/data 3) echo 0 > /sys/class/firmware/dell_rbu/loading The /sys/class/firmware/dell_rbu/ entries will remain till the following is done. -echo -1 > /sys/class/firmware/dell_rbu/loading + +:: + + echo -1 > /sys/class/firmware/dell_rbu/loading + Until this step is completed the driver cannot be unloaded. + Also echoing either mono, packet or init in to image_type will free up the memory allocated by the driver. If a user by accident executes steps 1 and 3 above without executing step 2; it will make the /sys/class/firmware/dell_rbu/ entries disappear. -The entries can be recreated by doing the following -echo init > /sys/devices/platform/dell_rbu/image_type -NOTE: echoing init in image_type does not change it original value. + +The entries can be recreated by doing the following:: + + echo init > /sys/devices/platform/dell_rbu/image_type + +.. note:: echoing init in image_type does not change it original value. Also the driver provides /sys/devices/platform/dell_rbu/data readonly file to read back the image downloaded. -NOTE: -This driver requires a patch for firmware_class.c which has the modified -request_firmware_nowait function. -Also after updating the BIOS image a user mode application needs to execute -code which sends the BIOS update request to the BIOS. So on the next reboot -the BIOS knows about the new image downloaded and it updates itself. -Also don't unload the rbu driver if the image has to be updated. +.. note:: + + This driver requires a patch for firmware_class.c which has the modified + request_firmware_nowait function. + + Also after updating the BIOS image a user mode application needs to execute + code which sends the BIOS update request to the BIOS. So on the next reboot + the BIOS knows about the new image downloaded and it updates itself. + Also don't unload the rbu driver if the image has to be updated. diff --git a/Documentation/device-mapper/dm-raid.txt b/Documentation/device-mapper/dm-raid.txt index 7e06e65586d4..4a0a7469fdd7 100644 --- a/Documentation/device-mapper/dm-raid.txt +++ b/Documentation/device-mapper/dm-raid.txt @@ -343,3 +343,4 @@ Version History 1.11.0 Fix table line argument order (wrong raid10_copies/raid10_format sequence) 1.11.1 Add raid4/5/6 journal write-back support via journal_mode option +1.12.1 fix for MD deadlock between mddev_suspend() and md_write_start() available diff --git a/Documentation/devicetree/bindings/clock/img,boston-clock.txt b/Documentation/devicetree/bindings/clock/img,boston-clock.txt new file mode 100644 index 000000000000..7bc5e9ffb624 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/img,boston-clock.txt @@ -0,0 +1,31 @@ +Binding for Imagination Technologies MIPS Boston clock sources. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +The device node must be a child node of the syscon node corresponding to the +Boston system's platform registers. + +Required properties: +- compatible : Should be "img,boston-clock". +- #clock-cells : Should be set to 1. + Values available for clock consumers can be found in the header file: + <dt-bindings/clock/boston-clock.h> + +Example: + + system-controller@17ffd000 { + compatible = "img,boston-platform-regs", "syscon"; + reg = <0x17ffd000 0x1000>; + + clk_boston: clock { + compatible = "img,boston-clock"; + #clock-cells = <1>; + }; + }; + + uart0: uart@17ffe000 { + /* ... */ + clocks = <&clk_boston BOSTON_CLK_SYS>; + }; diff --git a/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt b/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt index f69773f4252b..941bb6a6fb13 100644 --- a/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt +++ b/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt @@ -8,7 +8,6 @@ Required properties: Optional properties: - clocks: Reference to the crypto engine clock. -- dma-mask: The address mask limitation. Defaults to 64. Example: @@ -24,6 +23,5 @@ Example: interrupt-names = "mem", "ring0", "ring1", "ring2", "ring3", "eip"; clocks = <&cpm_syscon0 1 26>; - dma-mask = <0xff 0xffffffff>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt new file mode 100644 index 000000000000..bd6480b19535 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt @@ -0,0 +1,48 @@ +Device tree configuration for the I2C busses on the AST24XX and AST25XX SoCs. + +Required Properties: +- #address-cells : should be 1 +- #size-cells : should be 0 +- reg : address offset and range of bus +- compatible : should be "aspeed,ast2400-i2c-bus" + or "aspeed,ast2500-i2c-bus" +- clocks : root clock of bus, should reference the APB + clock +- interrupts : interrupt number +- interrupt-parent : interrupt controller for bus, should reference a + aspeed,ast2400-i2c-ic or aspeed,ast2500-i2c-ic + interrupt controller + +Optional Properties: +- bus-frequency : frequency of the bus clock in Hz defaults to 100 kHz when not + specified +- multi-master : states that there is another master active on this bus. + +Example: + +i2c { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1e78a000 0x1000>; + + i2c_ic: interrupt-controller@0 { + #interrupt-cells = <1>; + compatible = "aspeed,ast2400-i2c-ic"; + reg = <0x0 0x40>; + interrupts = <12>; + interrupt-controller; + }; + + i2c0: i2c-bus@40 { + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + reg = <0x40 0x40>; + compatible = "aspeed,ast2400-i2c-bus"; + clocks = <&clk_apb>; + bus-frequency = <100000>; + interrupts = <0>; + interrupt-parent = <&i2c_ic>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index fee26dc3e858..fbb0a6d8b964 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -20,7 +20,7 @@ Optional properties : - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds. This value which is by default 300ns is used to compute the tHIGH period. -Example : +Examples : i2c@f0000 { #address-cells = <1>; @@ -43,3 +43,17 @@ Example : i2c-sda-falling-time-ns = <300>; i2c-scl-falling-time-ns = <300>; }; + + i2c@1120000 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2000 0x100>; + clock-frequency = <400000>; + clocks = <&i2cclk>; + interrupts = <0>; + + eeprom@64 { + compatible = "linux,slave-24c02"; + reg = <0x40000064>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt b/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt new file mode 100644 index 000000000000..f1f3876bb8e8 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt @@ -0,0 +1,29 @@ +* NXP PCA PCA9564/PCA9665 I2C controller + +The PCA9564/PCA9665 serves as an interface between most standard +parallel-bus microcontrollers/microprocessors and the serial I2C-bus +and allows the parallel bus system to communicate bi-directionally +with the I2C-bus. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : one of "nxp,pca9564" or "nxp,pca9665" + +Optional properties + - interrupts : the interrupt number + - interrupt-parent : the phandle for the interrupt controller. + If an interrupt is not specified polling will be used. + - reset-gpios : gpio specifier for gpio connected to RESET_N pin. As the line + is active low, it should be marked GPIO_ACTIVE_LOW. + - clock-frequency : I2C bus frequency. + +Example: + i2c0: i2c@80000 { + compatible = "nxp,pca9564"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x80000 0x4>; + reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt b/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt new file mode 100644 index 000000000000..cb806d1ae4c9 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt @@ -0,0 +1,22 @@ +ZTE zx2967 I2C controller + +Required properties: + - compatible: must be "zte,zx296718-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + - clock-frequency: the desired I2C bus clock frequency. + +Examples: + + i2c@112000 { + compatible = "zte,zx296718-i2c"; + reg = <0x00112000 0x1000>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&osc24m>; + #address-cells = <1> + #size-cells = <0>; + clock-frequency = <1600000>; + }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index be57550e14e4..c9abbf3e4f68 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -26,6 +26,12 @@ the PCIe specification. * "priq" - PRI Queue not empty * "cmdq-sync" - CMD_SYNC complete * "gerror" - Global Error activated + * "combined" - The combined interrupt is optional, + and should only be provided if the + hardware supports just a single, + combined interrupt line. + If provided, then the combined interrupt + will be used in preference to any others. - #iommu-cells : See the generic IOMMU binding described in devicetree/bindings/pci/pci-iommu.txt @@ -49,6 +55,12 @@ the PCIe specification. - hisilicon,broken-prefetch-cmd : Avoid sending CMD_PREFETCH_* commands to the SMMU. +- cavium,cn9900-broken-page1-regspace + : Replaces all page 1 offsets used for EVTQ_PROD/CONS, + PRIQ_PROD/CONS register access with page 0 offsets. + Set for Cavium ThunderX2 silicon that doesn't support + SMMU page1 register space. + ** Example smmu@2b400000 { diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index aad98442788b..a58c173b7ab9 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -78,7 +78,6 @@ Example: }; dwmmc0@12200000 { - num-slots = <1>; cap-mmc-highspeed; cap-sd-highspeed; broken-cd; diff --git a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt index 85de99fcaa2f..c54e577eea07 100644 --- a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt @@ -24,6 +24,5 @@ Example: fifo-depth = <0x20>; bus-width = <4>; - num-slots = <1>; disable-wp; }; diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt index 8af1afcb86dc..07242d141773 100644 --- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt @@ -36,7 +36,6 @@ Example: /* Board portion */ dwmmc0@fcd03000 { - num-slots = <1>; vmmc-supply = <&ldo12>; fifo-depth = <0x100>; pinctrl-names = "default"; @@ -52,7 +51,6 @@ Example: dwmmc_1: dwmmc1@f723e000 { compatible = "hisilicon,hi6220-dw-mshc"; - num-slots = <0x1>; bus-width = <0x4>; disable-wp; cap-sd-highspeed; diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 9cb55ca57461..ef3e5f14067a 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -12,12 +12,12 @@ Required Properties: * #address-cells: should be 1. * #size-cells: should be 0. -# Slots: The slot specific information are contained within child-nodes with - each child-node representing a supported slot. There should be atleast one - child node representing a card slot. The name of the child node representing - the slot is recommended to be slot@n where n is the unique number of the slot - connected to the controller. The following are optional properties which - can be included in the slot child node. +# Slots (DEPRECATED): The slot specific information are contained within + child-nodes with each child-node representing a supported slot. There should + be atleast one child node representing a card slot. The name of the child node + representing the slot is recommended to be slot@n where n is the unique number + of the slot connected to the controller. The following are optional properties + which can be included in the slot child node. * reg: specifies the physical slot number. The valid values of this property is 0 to (num-slots -1), where num-slots is the value @@ -63,7 +63,7 @@ Optional properties: clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. (Use the "max-frequency" instead of "clock-freq-min-max".) -* num-slots: specifies the number of slots supported by the controller. +* num-slots (DEPRECATED): specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the value specified by num-slots. If this property is not specified, the value of num-slot property is assumed to be 1. @@ -124,7 +124,6 @@ board specific portions as listed below. dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; - num-slots = <1>; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; @@ -139,7 +138,6 @@ board specific portions as listed below. dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; - num-slots = <1>; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt index eaade0e5adeb..906819a90c2b 100644 --- a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt @@ -25,7 +25,6 @@ Example: clock-frequency = <50000000>; clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>; clock-names = "biu", "ciu"; - num-slots = <1>; max-frequency = <50000000>; cap-sdio-irq; cap-sd-highspeed; diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt index e593bbeb2115..504291d2e5c2 100644 --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -3,10 +3,23 @@ Required properties: - compatible : should be one of the following: "altr,socfpga-denali-nand" - for Altera SOCFPGA + "socionext,uniphier-denali-nand-v5a" - for Socionext UniPhier (v5a) + "socionext,uniphier-denali-nand-v5b" - for Socionext UniPhier (v5b) - reg : should contain registers location and length for data and reg. - reg-names: Should contain the reg names "nand_data" and "denali_reg" - interrupts : The interrupt number. +Optional properties: + - nand-ecc-step-size: see nand.txt for details. If present, the value must be + 512 for "altr,socfpga-denali-nand" + 1024 for "socionext,uniphier-denali-nand-v5a" + 1024 for "socionext,uniphier-denali-nand-v5b" + - nand-ecc-strength: see nand.txt for details. Valid values are: + 8, 15 for "altr,socfpga-denali-nand" + 8, 16, 24 for "socionext,uniphier-denali-nand-v5a" + 8, 16 for "socionext,uniphier-denali-nand-v5b" + - nand-ecc-maximize: see nand.txt for details + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/elm.txt b/Documentation/devicetree/bindings/mtd/elm.txt index 8c1528c421d4..59ddc61c1076 100644 --- a/Documentation/devicetree/bindings/mtd/elm.txt +++ b/Documentation/devicetree/bindings/mtd/elm.txt @@ -1,7 +1,7 @@ Error location module Required properties: -- compatible: Must be "ti,am33xx-elm" +- compatible: Must be "ti,am3352-elm" - reg: physical base address and size of the registers map. - interrupts: Interrupt number for the elm. diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 174f68c26c1b..dd559045593d 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -5,7 +5,7 @@ the GPMC controller with a name of "nand". All timing relevant properties as well as generic gpmc child properties are explained in a separate documents - please refer to -Documentation/devicetree/bindings/bus/ti-gpmc.txt +Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt For NAND specific properties such as ECC modes or bus width, please refer to Documentation/devicetree/bindings/mtd/nand.txt diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt index 4828c17bb784..131d3a74d0bd 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt @@ -5,7 +5,7 @@ child nodes of the GPMC controller with a name of "nor". All timing relevant properties as well as generic GPMC child properties are explained in a separate documents. Please refer to -Documentation/devicetree/bindings/bus/ti-gpmc.txt +Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt Required properties: - bank-width: Width of NOR flash in bytes. GPMC supports 8-bit and @@ -28,7 +28,7 @@ Required properties: Optional properties: - gpmc,XXX Additional GPMC timings and settings parameters. See - Documentation/devicetree/bindings/bus/ti-gpmc.txt + Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt Optional properties for partition table parsing: - #address-cells: should be set to 1 diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt index 5d8fa527c496..b6e8bfd024f4 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -5,7 +5,7 @@ the GPMC controller with a name of "onenand". All timing relevant properties as well as generic gpmc child properties are explained in a separate documents - please refer to -Documentation/devicetree/bindings/bus/ti-gpmc.txt +Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt Required properties: diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index d02acaff3c35..b289ef3c1b7e 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -4,7 +4,12 @@ The GPMI nand controller provides an interface to control the NAND flash chips. Required properties: - - compatible : should be "fsl,<chip>-gpmi-nand" + - compatible : should be "fsl,<chip>-gpmi-nand", chip can be: + * imx23 + * imx28 + * imx6q + * imx6sx + * imx7d - reg : should contain registers location and length for gpmi and bch. - reg-names: Should contain the reg names "gpmi-nand" and "bch" - interrupts : BCH interrupt number. @@ -13,6 +18,13 @@ Required properties: and GPMI DMA channel ID. Refer to dma.txt and fsl-mxs-dma.txt for details. - dma-names: Must be "rx-tx". + - clocks : clocks phandle and clock specifier corresponding to each clock + specified in clock-names. + - clock-names : The "gpmi_io" clock is always required. Which clocks are + exactly required depends on chip: + * imx23/imx28 : "gpmi_io" + * imx6q/sx : "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch" + * imx7d : "gpmi_io", "gpmi_bch_apb" Optional properties: - nand-on-flash-bbt: boolean to enable on flash bbt option if not diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt b/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt new file mode 100644 index 000000000000..7328eb92a03c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt @@ -0,0 +1,18 @@ +* MTD SPI driver for Microchip 23K256 (and similar) serial SRAM + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Must be one of "microchip,mchp23k256" or "microchip,mchp23lcv1024" +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Example: + + spi-sram@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "microchip,mchp23k256"; + reg = <0>; + spi-max-frequency = <20000000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt index 069c192ed5c2..dbf9e054c11c 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -12,7 +12,8 @@ tree nodes. The first part of NFC is NAND Controller Interface (NFI) HW. Required NFI properties: -- compatible: Should be "mediatek,mtxxxx-nfc". +- compatible: Should be one of "mediatek,mt2701-nfc", + "mediatek,mt2712-nfc". - reg: Base physical address and size of NFI. - interrupts: Interrupts of NFI. - clocks: NFI required clocks. @@ -141,7 +142,7 @@ Example: ============== Required BCH properties: -- compatible: Should be "mediatek,mtxxxx-ecc". +- compatible: Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc". - reg: Base physical address and size of ECC. - interrupts: Interrupts of ECC. - clocks: ECC required clocks. diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index b05601600083..133f3813719c 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -21,7 +21,7 @@ Optional NAND chip properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode. Supported values are: "none", "soft", "hw", "hw_syndrome", - "hw_oob_first". + "hw_oob_first", "on-die". Deprecated values: "soft_bch": use "soft" and nand-ecc-algo instead - nand-ecc-algo: string, algorithm of NAND ECC. diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 81a224da63be..36f3b769a626 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -1,29 +1,49 @@ -Representing flash partitions in devicetree +Flash partitions in device tree +=============================== -Partitions can be represented by sub-nodes of an mtd device. This can be used +Flash devices can be partitioned into one or more functional ranges (e.g. "boot +code", "nvram", "kernel"). + +Different devices may be partitioned in a different ways. Some may use a fixed +flash layout set at production time. Some may use on-flash table that describes +the geometry and naming/purpose of each functional region. It is also possible +to see these methods mixed. + +To assist system software in locating partitions, we allow describing which +method is used for a given flash device. To describe the method there should be +a subnode of the flash device that is named 'partitions'. It must have a +'compatible' property, which is used to identify the method to use. + +We currently only document a binding for fixed layouts. + + +Fixed Partitions +================ + +Partitions can be represented by sub-nodes of a flash device. This can be used on platforms which have strong conventions about which portions of a flash are used for what purposes, but which don't use an on-flash partition table such as RedBoot. -The partition table should be a subnode of the mtd node and should be named +The partition table should be a subnode of the flash node and should be named 'partitions'. This node should have the following property: - compatible : (required) must be "fixed-partitions" Partitions are then defined in subnodes of the partitions node. -For backwards compatibility partitions as direct subnodes of the mtd device are +For backwards compatibility partitions as direct subnodes of the flash device are supported. This use is discouraged. NOTE: also for backwards compatibility, direct subnodes that have a compatible string are not considered partitions, as they may be used for other bindings. #address-cells & #size-cells must both be present in the partitions subnode of the -mtd device. There are two valid values for both: +flash device. There are two valid values for both: <1>: for partitions that require a single 32-bit cell to represent their size/address (aka the value is below 4 GiB) <2>: for partitions that require two 32-bit cells to represent their size/address (aka the value is 4 GiB or greater). Required properties: -- reg : The partition's offset and size within the mtd bank. +- reg : The partition's offset and size within the flash Optional properties: - label : The label / name for this partition. If omitted, the label is taken diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt index 2fefa1a44afd..ad16c1f481f7 100644 --- a/Documentation/devicetree/bindings/net/brcm,amac.txt +++ b/Documentation/devicetree/bindings/net/brcm,amac.txt @@ -11,6 +11,7 @@ Required properties: - reg-names: Names of the registers. "amac_base": Address and length of the GMAC registers "idm_base": Address and length of the GMAC IDM registers + (required for NSP and Northstar2) "nicpm_base": Address and length of the NIC Port Manager registers (required for Northstar2) - interrupts: Interrupt number diff --git a/Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt b/Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt deleted file mode 100644 index 022946caa7e2..000000000000 --- a/Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt +++ /dev/null @@ -1,24 +0,0 @@ -Broadcom GMAC Ethernet Controller Device Tree Bindings -------------------------------------------------------------- - -Required properties: - - compatible: "brcm,bgmac-nsp" - - reg: Address and length of the GMAC registers, - Address and length of the GMAC IDM registers - - reg-names: Names of the registers. Must have both "gmac_base" and - "idm_base" - - interrupts: Interrupt number - -Optional properties: -- mac-address: See ethernet.txt file in the same directory - -Examples: - -gmac0: ethernet@18022000 { - compatible = "brcm,bgmac-nsp"; - reg = <0x18022000 0x1000>, - <0x18110000 0x1000>; - reg-names = "gmac_base", "idm_base"; - interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; -}; diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt index ace4a64b3695..f7da3d73ca1b 100644 --- a/Documentation/devicetree/bindings/net/gpmc-eth.txt +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt @@ -9,7 +9,7 @@ the GPMC controller with an "ethernet" name. All timing relevant properties as well as generic GPMC child properties are explained in a separate documents. Please refer to -Documentation/devicetree/bindings/bus/ti-gpmc.txt +Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt For the properties relevant to the ethernet controller connected to the GPMC refer to the binding documentation of the device. For example, the documentation @@ -43,7 +43,7 @@ Required properties: Optional properties: - gpmc,XXX Additional GPMC timings and settings parameters. See - Documentation/devicetree/bindings/bus/ti-gpmc.txt + Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt Example: diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt index 194926f77194..1ff02afdc55a 100644 --- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -4,7 +4,7 @@ Required properties: - compatible: Should be one of the following. - "rockchip,rk3066a-efuse" - for RK3066a SoCs. - "rockchip,rk3188-efuse" - for RK3188 SoCs. - - "rockchip,rk322x-efuse" - for RK322x SoCs. + - "rockchip,rk3228-efuse" - for RK3228 SoCs. - "rockchip,rk3288-efuse" - for RK3288 SoCs. - "rockchip,rk3399-efuse" - for RK3399 SoCs. - reg: Should contain the registers location and exact eFuse size diff --git a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt index 07590bcdad15..7c04e22a5d6a 100644 --- a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt +++ b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt @@ -1,13 +1,20 @@ -* Broadcom Digital Timing Engine(DTE) based PTP clock driver +* Broadcom Digital Timing Engine(DTE) based PTP clock Required properties: -- compatible: should be "brcm,ptp-dte" +- compatible: should contain the core compatibility string + and the SoC compatibility string. The SoC + compatibility string is to handle SoC specific + hardware differences. + Core compatibility string: + "brcm,ptp-dte" + SoC compatibility strings: + "brcm,iproc-ptp-dte" - for iproc based SoC's - reg: address and length of the DTE block's NCO registers Example: -ptp_dte: ptp_dte@180af650 { - compatible = "brcm,ptp-dte"; +ptp: ptp-dte@180af650 { + compatible = "brcm,iproc-ptp-dte", "brcm,ptp-dte"; reg = <0x180af650 0x10>; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-meson.txt b/Documentation/devicetree/bindings/pwm/pwm-meson.txt index 5376a4468cb6..5b07bebbf6f7 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-meson.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-meson.txt @@ -2,7 +2,9 @@ Amlogic Meson PWM Controller ============================ Required properties: -- compatible: Shall contain "amlogic,meson8b-pwm" or "amlogic,meson-gxbb-pwm". +- compatible: Shall contain "amlogic,meson8b-pwm" + or "amlogic,meson-gxbb-pwm" + or "amlogic,meson-gxbb-ao-pwm" - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt index 6dd040363e5e..3e6d55018d7a 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt @@ -24,7 +24,7 @@ Example: compatible = "st,stm32-timers"; reg = <0x40010000 0x400>; clocks = <&rcc 0 160>; - clock-names = "clk_int"; + clock-names = "int"; pwm { compatible = "st,stm32-pwm"; diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt index d6de64335022..7e94b802395d 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -8,6 +8,7 @@ Required Properties: - "renesas,pwm-r8a7791": for R-Car M2-W - "renesas,pwm-r8a7794": for R-Car E2 - "renesas,pwm-r8a7795": for R-Car H3 + - "renesas,pwm-r8a7796": for R-Car M3-W - reg: base address and length of the registers block for the PWM. - #pwm-cells: should be 2. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/rtc/brcm,brcmstb-waketimer.txt b/Documentation/devicetree/bindings/rtc/brcm,brcmstb-waketimer.txt new file mode 100644 index 000000000000..1d990bcc0baf --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/brcm,brcmstb-waketimer.txt @@ -0,0 +1,22 @@ +Broadcom STB wake-up Timer + +The Broadcom STB wake-up timer provides a 27Mhz resolution timer, with the +ability to wake up the system from low-power suspend/standby modes. + +Required properties: +- compatible : should contain "brcm,brcmstb-waketimer" +- reg : the register start and length for the WKTMR block +- interrupts : The TIMER interrupt +- interrupt-parent: The phandle to the Always-On (AON) Power Management (PM) L2 + interrupt controller node +- clocks : The phandle to the UPG fixed clock (27Mhz domain) + +Example: + +waketimer@f0411580 { + compatible = "brcm,brcmstb-waketimer"; + reg = <0xf0411580 0x14>; + interrupts = <0x3>; + interrupt-parent = <&aon_pm_l2_intc>; + clocks = <&upg_fixed>; +}; diff --git a/Documentation/devicetree/bindings/rtc/cortina,gemini.txt b/Documentation/devicetree/bindings/rtc/cortina,gemini.txt deleted file mode 100644 index 4ce4e794ddbb..000000000000 --- a/Documentation/devicetree/bindings/rtc/cortina,gemini.txt +++ /dev/null @@ -1,14 +0,0 @@ -* Cortina Systems Gemini RTC - -Gemini SoC real-time clock. - -Required properties: -- compatible : Should be "cortina,gemini-rtc" - -Examples: - -rtc@45000000 { - compatible = "cortina,gemini-rtc"; - reg = <0x45000000 0x100>; - interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/rtc/faraday,ftrtc010.txt b/Documentation/devicetree/bindings/rtc/faraday,ftrtc010.txt new file mode 100644 index 000000000000..e3938f5e0b6c --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/faraday,ftrtc010.txt @@ -0,0 +1,28 @@ +* Faraday Technology FTRTC010 Real Time Clock + +This RTC appears in for example the Storlink Gemini family of +SoCs. + +Required properties: +- compatible : Should be one of: + "faraday,ftrtc010" + "cortina,gemini-rtc", "faraday,ftrtc010" + +Optional properties: +- clocks: when present should contain clock references to the + PCLK and EXTCLK clocks. Faraday calls the later CLK1HZ and + says the clock should be 1 Hz, but implementers actually seem + to choose different clocks here, like Cortina who chose + 32768 Hz (a typical low-power clock). +- clock-names: should name the clocks "PCLK" and "EXTCLK" + respectively. + +Examples: + +rtc@45000000 { + compatible = "cortina,gemini-rtc"; + reg = <0x45000000 0x100>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&foo 0>, <&foo 1>; + clock-names = "PCLK", "EXTCLK"; +}; diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt index e2837b951237..0a4c371a9b7a 100644 --- a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt @@ -1,17 +1,25 @@ STM32 Real Time Clock Required properties: -- compatible: "st,stm32-rtc". +- compatible: can be either "st,stm32-rtc" or "st,stm32h7-rtc", depending on + the device is compatible with stm32(f4/f7) or stm32h7. - reg: address range of rtc register set. -- clocks: reference to the clock entry ck_rtc. +- clocks: can use up to two clocks, depending on part used: + - "rtc_ck": RTC clock source. + It is required on stm32(f4/f7) and stm32h7. + - "pclk": RTC APB interface clock. + It is not present on stm32(f4/f7). + It is required on stm32h7. +- clock-names: must be "rtc_ck" and "pclk". + It is required only on stm32h7. - interrupt-parent: phandle for the interrupt controller. - interrupts: rtc alarm interrupt. - st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain (RTC registers) write protection. -Optional properties (to override default ck_rtc parent clock): -- assigned-clocks: reference to the ck_rtc clock entry. -- assigned-clock-parents: phandle of the new parent clock of ck_rtc. +Optional properties (to override default rtc_ck parent clock): +- assigned-clocks: reference to the rtc_ck clock entry. +- assigned-clock-parents: phandle of the new parent clock of rtc_ck. Example: @@ -25,3 +33,17 @@ Example: interrupts = <17 1>; st,syscfg = <&pwrcfg>; }; + + rtc: rtc@58004000 { + compatible = "st,stm32h7-rtc"; + reg = <0x58004000 0x400>; + clocks = <&rcc RTCAPB_CK>, <&rcc RTC_CK>; + clock-names = "pclk", "rtc_ck"; + assigned-clocks = <&rcc RTC_CK>; + assigned-clock-parents = <&rcc LSE_CK>; + interrupt-parent = <&exti>; + interrupts = <17 1>; + interrupt-names = "alarm"; + st,syscfg = <&pwrcfg>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index e6b572409cf5..574c3a2c77d5 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -9,7 +9,6 @@ Optional properties: - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. -- fsl,dma-size : Indicate the size of the DMA buffer and its periods Please check Documentation/devicetree/bindings/serial/serial.txt for the complete list of generic properties. @@ -29,5 +28,4 @@ uart1: serial@73fbc000 { interrupts = <31>; uart-has-rtscts; fsl,dte-mode; - fsl,dma-size = <1024 4>; }; diff --git a/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt new file mode 100644 index 000000000000..b935b526d2f3 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt @@ -0,0 +1,23 @@ +* Dialog Semiconductor DA9062/61 Watchdog Timer + +Required properties: + +- compatible: should be one of the following valid compatible string lines: + "dlg,da9061-watchdog", "dlg,da9062-watchdog" + "dlg,da9062-watchdog" + +Example: DA9062 + + pmic0: da9062@58 { + watchdog { + compatible = "dlg,da9062-watchdog"; + }; + }; + +Example: DA9061 using a fall-back compatible for the DA9062 watchdog driver + + pmic0: da9061@58 { + watchdog { + compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog"; + }; + }; diff --git a/Documentation/devicetree/bindings/watchdog/dw_wdt.txt b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt index 08e16f684f2d..eb0914420c7c 100644 --- a/Documentation/devicetree/bindings/watchdog/dw_wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt @@ -10,6 +10,8 @@ Required Properties: Optional Properties: - interrupts : The interrupt used for the watchdog timeout warning. +- resets : phandle pointing to the system reset controller with + line index for the watchdog. Example: @@ -18,4 +20,5 @@ Example: reg = <0xffd02000 0x1000>; interrupts = <0 171 4>; clocks = <&per_base_clk>; + resets = <&rst WDT0_RESET>; }; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index da24e3133417..9e306afbbd49 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -2,10 +2,11 @@ Renesas Watchdog Timer (WDT) Controller Required properties: - compatible : Should be "renesas,<soctype>-wdt", and - "renesas,rcar-gen3-wdt" as fallback. + "renesas,rcar-gen3-wdt" or "renesas,rza-wdt" as fallback. Examples with soctypes are: - "renesas,r8a7795-wdt" (R-Car H3) - "renesas,r8a7796-wdt" (R-Car M3-W) + - "renesas,r7s72100-wdt" (RZ/A1) When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the generic @@ -17,6 +18,7 @@ Required properties: Optional properties: - timeout-sec : Contains the watchdog timeout in seconds - power-domains : the power domain the WDT belongs to +- interrupts: Some WDTs have an interrupt when used in interval timer mode Examples: diff --git a/Documentation/devicetree/bindings/watchdog/st,stm32-iwdg.txt b/Documentation/devicetree/bindings/watchdog/st,stm32-iwdg.txt new file mode 100644 index 000000000000..cc13b10a3f82 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/st,stm32-iwdg.txt @@ -0,0 +1,19 @@ +STM32 Independent WatchDoG (IWDG) +--------------------------------- + +Required properties: +- compatible: "st,stm32-iwdg" +- reg: physical base address and length of the registers set for the device +- clocks: must contain a single entry describing the clock input + +Optional Properties: +- timeout-sec: Watchdog timeout value in seconds. + +Example: + +iwdg: watchdog@40003000 { + compatible = "st,stm32-iwdg"; + reg = <0x40003000 0x400>; + clocks = <&clk_lsi>; + timeout-sec = <32>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/uniphier-wdt.txt b/Documentation/devicetree/bindings/watchdog/uniphier-wdt.txt new file mode 100644 index 000000000000..bf6337546dd1 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/uniphier-wdt.txt @@ -0,0 +1,20 @@ +UniPhier watchdog timer controller + +This UniPhier watchdog timer controller must be under sysctrl node. + +Required properties: +- compatible: should be "socionext,uniphier-wdt" + +Example: + + sysctrl@61840000 { + compatible = "socionext,uniphier-ld11-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x4000>; + + watchdog { + compatible = "socionext,uniphier-wdt"; + } + + other nodes ... + }; diff --git a/Documentation/digsig.txt b/Documentation/digsig.txt index 3f682889068b..f6a8902d3ef7 100644 --- a/Documentation/digsig.txt +++ b/Documentation/digsig.txt @@ -1,13 +1,20 @@ +================================== Digital Signature Verification API +================================== -CONTENTS +:Author: Dmitry Kasatkin +:Date: 06.10.2011 -1. Introduction -2. API -3. User-space utilities +.. CONTENTS -1. Introduction + 1. Introduction + 2. API + 3. User-space utilities + + +Introduction +============ Digital signature verification API provides a method to verify digital signature. Currently digital signatures are used by the IMA/EVM integrity protection subsystem. @@ -17,25 +24,25 @@ GnuPG multi-precision integers (MPI) library. The kernel port provides memory allocation errors handling, has been refactored according to kernel coding style, and checkpatch.pl reported errors and warnings have been fixed. -Public key and signature consist of header and MPIs. - -struct pubkey_hdr { - uint8_t version; /* key format version */ - time_t timestamp; /* key made, always 0 for now */ - uint8_t algo; - uint8_t nmpi; - char mpi[0]; -} __packed; - -struct signature_hdr { - uint8_t version; /* signature format version */ - time_t timestamp; /* signature made */ - uint8_t algo; - uint8_t hash; - uint8_t keyid[8]; - uint8_t nmpi; - char mpi[0]; -} __packed; +Public key and signature consist of header and MPIs:: + + struct pubkey_hdr { + uint8_t version; /* key format version */ + time_t timestamp; /* key made, always 0 for now */ + uint8_t algo; + uint8_t nmpi; + char mpi[0]; + } __packed; + + struct signature_hdr { + uint8_t version; /* signature format version */ + time_t timestamp; /* signature made */ + uint8_t algo; + uint8_t hash; + uint8_t keyid[8]; + uint8_t nmpi; + char mpi[0]; + } __packed; keyid equals to SHA1[12-19] over the total key content. Signature header is used as an input to generate a signature. @@ -43,31 +50,33 @@ Such approach insures that key or signature header could not be changed. It protects timestamp from been changed and can be used for rollback protection. -2. API +API +=== -API currently includes only 1 function: +API currently includes only 1 function:: digsig_verify() - digital signature verification with public key -/** - * digsig_verify() - digital signature verification with public key - * @keyring: keyring to search key in - * @sig: digital signature - * @sigen: length of the signature - * @data: data - * @datalen: length of the data - * @return: 0 on success, -EINVAL otherwise - * - * Verifies data integrity against digital signature. - * Currently only RSA is supported. - * Normally hash of the content is used as a data for this function. - * - */ -int digsig_verify(struct key *keyring, const char *sig, int siglen, - const char *data, int datalen); - -3. User-space utilities + /** + * digsig_verify() - digital signature verification with public key + * @keyring: keyring to search key in + * @sig: digital signature + * @sigen: length of the signature + * @data: data + * @datalen: length of the data + * @return: 0 on success, -EINVAL otherwise + * + * Verifies data integrity against digital signature. + * Currently only RSA is supported. + * Normally hash of the content is used as a data for this function. + * + */ + int digsig_verify(struct key *keyring, const char *sig, int siglen, + const char *data, int datalen); + +User-space utilities +==================== The signing and key management utilities evm-utils provide functionality to generate signatures, to load keys into the kernel keyring. @@ -75,22 +84,18 @@ Keys can be in PEM or converted to the kernel format. When the key is added to the kernel keyring, the keyid defines the name of the key: 5D2B05FC633EE3E8 in the example bellow. -Here is example output of the keyctl utility. - -$ keyctl show -Session Keyring - -3 --alswrv 0 0 keyring: _ses -603976250 --alswrv 0 -1 \_ keyring: _uid.0 -817777377 --alswrv 0 0 \_ user: kmk -891974900 --alswrv 0 0 \_ encrypted: evm-key -170323636 --alswrv 0 0 \_ keyring: _module -548221616 --alswrv 0 0 \_ keyring: _ima -128198054 --alswrv 0 0 \_ keyring: _evm - -$ keyctl list 128198054 -1 key in keyring: -620789745: --alswrv 0 0 user: 5D2B05FC633EE3E8 - - -Dmitry Kasatkin -06.10.2011 +Here is example output of the keyctl utility:: + + $ keyctl show + Session Keyring + -3 --alswrv 0 0 keyring: _ses + 603976250 --alswrv 0 -1 \_ keyring: _uid.0 + 817777377 --alswrv 0 0 \_ user: kmk + 891974900 --alswrv 0 0 \_ encrypted: evm-key + 170323636 --alswrv 0 0 \_ keyring: _module + 548221616 --alswrv 0 0 \_ keyring: _ima + 128198054 --alswrv 0 0 \_ keyring: _evm + + $ keyctl list 128198054 + 1 key in keyring: + 620789745: --alswrv 0 0 user: 5D2B05FC633EE3E8 diff --git a/Documentation/driver-api/basics.rst b/Documentation/driver-api/basics.rst index 472e7a664d13..ab82250c7727 100644 --- a/Documentation/driver-api/basics.rst +++ b/Documentation/driver-api/basics.rst @@ -106,9 +106,6 @@ Kernel utility functions .. kernel-doc:: kernel/sys.c :export: -.. kernel-doc:: kernel/rcu/srcu.c - :export: - .. kernel-doc:: kernel/rcu/tree.c :export: diff --git a/Documentation/driver-api/i2c.rst b/Documentation/driver-api/i2c.rst index 0bf86a445d01..7582c079d747 100644 --- a/Documentation/driver-api/i2c.rst +++ b/Documentation/driver-api/i2c.rst @@ -41,5 +41,8 @@ i2c_adapter devices which don't support those I2C operations. .. kernel-doc:: drivers/i2c/i2c-boardinfo.c :functions: i2c_register_board_info -.. kernel-doc:: drivers/i2c/i2c-core.c +.. kernel-doc:: drivers/i2c/i2c-core-base.c + :export: + +.. kernel-doc:: drivers/i2c/i2c-core-smbus.c :export: diff --git a/Documentation/efi-stub.txt b/Documentation/efi-stub.txt index e15746988261..41df801f9a50 100644 --- a/Documentation/efi-stub.txt +++ b/Documentation/efi-stub.txt @@ -1,5 +1,6 @@ - The EFI Boot Stub - --------------------------- +================= +The EFI Boot Stub +================= On the x86 and ARM platforms, a kernel zImage/bzImage can masquerade as a PE/COFF image, thereby convincing EFI firmware loaders to load @@ -25,7 +26,8 @@ a certain sense it *IS* the boot loader. The EFI boot stub is enabled with the CONFIG_EFI_STUB kernel option. -**** How to install bzImage.efi +How to install bzImage.efi +-------------------------- The bzImage located in arch/x86/boot/bzImage must be copied to the EFI System Partition (ESP) and renamed with the extension ".efi". Without @@ -37,14 +39,16 @@ may not need to be renamed. Similarly for arm64, arch/arm64/boot/Image should be copied but not necessarily renamed. -**** Passing kernel parameters from the EFI shell +Passing kernel parameters from the EFI shell +-------------------------------------------- -Arguments to the kernel can be passed after bzImage.efi, e.g. +Arguments to the kernel can be passed after bzImage.efi, e.g.:: fs0:> bzImage.efi console=ttyS0 root=/dev/sda4 -**** The "initrd=" option +The "initrd=" option +-------------------- Like most boot loaders, the EFI stub allows the user to specify multiple initrd files using the "initrd=" option. This is the only EFI @@ -54,9 +58,9 @@ kernel when it boots. The path to the initrd file must be an absolute path from the beginning of the ESP, relative path names do not work. Also, the path is an EFI-style path and directory elements must be separated with -backslashes (\). For example, given the following directory layout, +backslashes (\). For example, given the following directory layout:: -fs0:> + fs0:> Kernels\ bzImage.efi initrd-large.img @@ -66,7 +70,7 @@ fs0:> initrd-medium.img to boot with the initrd-large.img file if the current working -directory is fs0:\Kernels, the following command must be used, +directory is fs0:\Kernels, the following command must be used:: fs0:\Kernels> bzImage.efi initrd=\Kernels\initrd-large.img @@ -76,7 +80,8 @@ which understands relative paths, whereas the rest of the command line is passed to bzImage.efi. -**** The "dtb=" option +The "dtb=" option +----------------- For the ARM and arm64 architectures, we also need to be able to provide a device tree to the kernel. This is done with the "dtb=" command line option, diff --git a/Documentation/eisa.txt b/Documentation/eisa.txt index a55e4910924e..2806e5544e43 100644 --- a/Documentation/eisa.txt +++ b/Documentation/eisa.txt @@ -1,4 +1,8 @@ -EISA bus support (Marc Zyngier <maz@wild-wind.fr.eu.org>) +================ +EISA bus support +================ + +:Author: Marc Zyngier <maz@wild-wind.fr.eu.org> This document groups random notes about porting EISA drivers to the new EISA/sysfs API. @@ -14,168 +18,189 @@ detection code is generally also used to probe ISA cards). Moreover, most EISA drivers are among the oldest Linux drivers so, as you can imagine, some dust has settled here over the years. -The EISA infrastructure is made up of three parts : +The EISA infrastructure is made up of three parts: - The bus code implements most of the generic code. It is shared - among all the architectures that the EISA code runs on. It - implements bus probing (detecting EISA cards available on the bus), - allocates I/O resources, allows fancy naming through sysfs, and - offers interfaces for driver to register. + among all the architectures that the EISA code runs on. It + implements bus probing (detecting EISA cards available on the bus), + allocates I/O resources, allows fancy naming through sysfs, and + offers interfaces for driver to register. - The bus root driver implements the glue between the bus hardware - and the generic bus code. It is responsible for discovering the - device implementing the bus, and setting it up to be latter probed - by the bus code. This can go from something as simple as reserving - an I/O region on x86, to the rather more complex, like the hppa - EISA code. This is the part to implement in order to have EISA - running on an "new" platform. + and the generic bus code. It is responsible for discovering the + device implementing the bus, and setting it up to be latter probed + by the bus code. This can go from something as simple as reserving + an I/O region on x86, to the rather more complex, like the hppa + EISA code. This is the part to implement in order to have EISA + running on an "new" platform. - The driver offers the bus a list of devices that it manages, and - implements the necessary callbacks to probe and release devices - whenever told to. + implements the necessary callbacks to probe and release devices + whenever told to. Every function/structure below lives in <linux/eisa.h>, which depends heavily on <linux/device.h>. -** Bus root driver : +Bus root driver +=============== + +:: -int eisa_root_register (struct eisa_root_device *root); + int eisa_root_register (struct eisa_root_device *root); The eisa_root_register function is used to declare a device as the root of an EISA bus. The eisa_root_device structure holds a reference -to this device, as well as some parameters for probing purposes. - -struct eisa_root_device { - struct device *dev; /* Pointer to bridge device */ - struct resource *res; - unsigned long bus_base_addr; - int slots; /* Max slot number */ - int force_probe; /* Probe even when no slot 0 */ - u64 dma_mask; /* from bridge device */ - int bus_nr; /* Set by eisa_root_register */ - struct resource eisa_root_res; /* ditto */ -}; - -node : used for eisa_root_register internal purpose -dev : pointer to the root device -res : root device I/O resource -bus_base_addr : slot 0 address on this bus -slots : max slot number to probe -force_probe : Probe even when slot 0 is empty (no EISA mainboard) -dma_mask : Default DMA mask. Usually the bridge device dma_mask. -bus_nr : unique bus id, set by eisa_root_register - -** Driver : - -int eisa_driver_register (struct eisa_driver *edrv); -void eisa_driver_unregister (struct eisa_driver *edrv); +to this device, as well as some parameters for probing purposes:: + + struct eisa_root_device { + struct device *dev; /* Pointer to bridge device */ + struct resource *res; + unsigned long bus_base_addr; + int slots; /* Max slot number */ + int force_probe; /* Probe even when no slot 0 */ + u64 dma_mask; /* from bridge device */ + int bus_nr; /* Set by eisa_root_register */ + struct resource eisa_root_res; /* ditto */ + }; + +============= ====================================================== +node used for eisa_root_register internal purpose +dev pointer to the root device +res root device I/O resource +bus_base_addr slot 0 address on this bus +slots max slot number to probe +force_probe Probe even when slot 0 is empty (no EISA mainboard) +dma_mask Default DMA mask. Usually the bridge device dma_mask. +bus_nr unique bus id, set by eisa_root_register +============= ====================================================== + +Driver +====== + +:: + + int eisa_driver_register (struct eisa_driver *edrv); + void eisa_driver_unregister (struct eisa_driver *edrv); Clear enough ? -struct eisa_device_id { - char sig[EISA_SIG_LEN]; - unsigned long driver_data; -}; - -struct eisa_driver { - const struct eisa_device_id *id_table; - struct device_driver driver; -}; - -id_table : an array of NULL terminated EISA id strings, - followed by an empty string. Each string can - optionally be paired with a driver-dependent value - (driver_data). - -driver : a generic driver, such as described in - Documentation/driver-model/driver.txt. Only .name, - .probe and .remove members are mandatory. - -An example is the 3c59x driver : - -static struct eisa_device_id vortex_eisa_ids[] = { - { "TCM5920", EISA_3C592_OFFSET }, - { "TCM5970", EISA_3C597_OFFSET }, - { "" } -}; - -static struct eisa_driver vortex_eisa_driver = { - .id_table = vortex_eisa_ids, - .driver = { - .name = "3c59x", - .probe = vortex_eisa_probe, - .remove = vortex_eisa_remove - } -}; - -** Device : +:: + + struct eisa_device_id { + char sig[EISA_SIG_LEN]; + unsigned long driver_data; + }; + + struct eisa_driver { + const struct eisa_device_id *id_table; + struct device_driver driver; + }; + +=============== ==================================================== +id_table an array of NULL terminated EISA id strings, + followed by an empty string. Each string can + optionally be paired with a driver-dependent value + (driver_data). + +driver a generic driver, such as described in + Documentation/driver-model/driver.txt. Only .name, + .probe and .remove members are mandatory. +=============== ==================================================== + +An example is the 3c59x driver:: + + static struct eisa_device_id vortex_eisa_ids[] = { + { "TCM5920", EISA_3C592_OFFSET }, + { "TCM5970", EISA_3C597_OFFSET }, + { "" } + }; + + static struct eisa_driver vortex_eisa_driver = { + .id_table = vortex_eisa_ids, + .driver = { + .name = "3c59x", + .probe = vortex_eisa_probe, + .remove = vortex_eisa_remove + } + }; + +Device +====== The sysfs framework calls .probe and .remove functions upon device discovery and removal (note that the .remove function is only called when driver is built as a module). Both functions are passed a pointer to a 'struct device', which is -encapsulated in a 'struct eisa_device' described as follows : - -struct eisa_device { - struct eisa_device_id id; - int slot; - int state; - unsigned long base_addr; - struct resource res[EISA_MAX_RESOURCES]; - u64 dma_mask; - struct device dev; /* generic device */ -}; - -id : EISA id, as read from device. id.driver_data is set from the - matching driver EISA id. -slot : slot number which the device was detected on -state : set of flags indicating the state of the device. Current - flags are EISA_CONFIG_ENABLED and EISA_CONFIG_FORCED. -res : set of four 256 bytes I/O regions allocated to this device -dma_mask: DMA mask set from the parent device. -dev : generic device (see Documentation/driver-model/device.txt) +encapsulated in a 'struct eisa_device' described as follows:: + + struct eisa_device { + struct eisa_device_id id; + int slot; + int state; + unsigned long base_addr; + struct resource res[EISA_MAX_RESOURCES]; + u64 dma_mask; + struct device dev; /* generic device */ + }; + +======== ============================================================ +id EISA id, as read from device. id.driver_data is set from the + matching driver EISA id. +slot slot number which the device was detected on +state set of flags indicating the state of the device. Current + flags are EISA_CONFIG_ENABLED and EISA_CONFIG_FORCED. +res set of four 256 bytes I/O regions allocated to this device +dma_mask DMA mask set from the parent device. +dev generic device (see Documentation/driver-model/device.txt) +======== ============================================================ You can get the 'struct eisa_device' from 'struct device' using the 'to_eisa_device' macro. -** Misc stuff : +Misc stuff +========== + +:: -void eisa_set_drvdata (struct eisa_device *edev, void *data); + void eisa_set_drvdata (struct eisa_device *edev, void *data); Stores data into the device's driver_data area. -void *eisa_get_drvdata (struct eisa_device *edev): +:: + + void *eisa_get_drvdata (struct eisa_device *edev): Gets the pointer previously stored into the device's driver_data area. -int eisa_get_region_index (void *addr); +:: + + int eisa_get_region_index (void *addr); Returns the region number (0 <= x < EISA_MAX_RESOURCES) of a given address. -** Kernel parameters : +Kernel parameters +================= -eisa_bus.enable_dev : +eisa_bus.enable_dev + A comma-separated list of slots to be enabled, even if the firmware + set the card as disabled. The driver must be able to properly + initialize the device in such conditions. -A comma-separated list of slots to be enabled, even if the firmware -set the card as disabled. The driver must be able to properly -initialize the device in such conditions. +eisa_bus.disable_dev + A comma-separated list of slots to be enabled, even if the firmware + set the card as enabled. The driver won't be called to handle this + device. -eisa_bus.disable_dev : +virtual_root.force_probe + Force the probing code to probe EISA slots even when it cannot find an + EISA compliant mainboard (nothing appears on slot 0). Defaults to 0 + (don't force), and set to 1 (force probing) when either + CONFIG_ALPHA_JENSEN or CONFIG_EISA_VLB_PRIMING are set. -A comma-separated list of slots to be enabled, even if the firmware -set the card as enabled. The driver won't be called to handle this -device. - -virtual_root.force_probe : - -Force the probing code to probe EISA slots even when it cannot find an -EISA compliant mainboard (nothing appears on slot 0). Defaults to 0 -(don't force), and set to 1 (force probing) when either -CONFIG_ALPHA_JENSEN or CONFIG_EISA_VLB_PRIMING are set. - -** Random notes : +Random notes +============ Converting an EISA driver to the new API mostly involves *deleting* code (since probing is now in the core EISA code). Unfortunately, most @@ -194,9 +219,11 @@ routine. For example, switching your favorite EISA SCSI card to the "hotplug" model is "the right thing"(tm). -** Thanks : +Thanks +====== + +I'd like to thank the following people for their help: -I'd like to thank the following people for their help : - Xavier Benigni for lending me a wonderful Alpha Jensen, - James Bottomley, Jeff Garzik for getting this stuff into the kernel, - Andries Brouwer for contributing numerous EISA ids, diff --git a/Documentation/fault-injection/fault-injection.txt b/Documentation/fault-injection/fault-injection.txt index 415484f3d59a..918972babcd8 100644 --- a/Documentation/fault-injection/fault-injection.txt +++ b/Documentation/fault-injection/fault-injection.txt @@ -134,6 +134,23 @@ use the boot option: fail_futex= mmc_core.fail_request=<interval>,<probability>,<space>,<times> +o proc entries + +- /proc/<pid>/fail-nth: +- /proc/self/task/<tid>/fail-nth: + + Write to this file of integer N makes N-th call in the task fail. + Read from this file returns a integer value. A value of '0' indicates + that the fault setup with a previous write to this file was injected. + A positive integer N indicates that the fault wasn't yet injected. + Note that this file enables all types of faults (slab, futex, etc). + This setting takes precedence over all other generic debugfs settings + like probability, interval, times, etc. But per-capability settings + (e.g. fail_futex/ignore-private) take precedence over it. + + This feature is intended for systematic testing of faults in a single + system call. See an example below. + How to add new fault injection capability ----------------------------------------- @@ -278,3 +295,65 @@ allocation failure. # env FAILCMD_TYPE=fail_page_alloc \ ./tools/testing/fault-injection/failcmd.sh --times=100 \ -- make -C tools/testing/selftests/ run_tests + +Systematic faults using fail-nth +--------------------------------- + +The following code systematically faults 0-th, 1-st, 2-nd and so on +capabilities in the socketpair() system call. + +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/socket.h> +#include <sys/syscall.h> +#include <fcntl.h> +#include <unistd.h> +#include <string.h> +#include <stdlib.h> +#include <stdio.h> +#include <errno.h> + +int main() +{ + int i, err, res, fail_nth, fds[2]; + char buf[128]; + + system("echo N > /sys/kernel/debug/failslab/ignore-gfp-wait"); + sprintf(buf, "/proc/self/task/%ld/fail-nth", syscall(SYS_gettid)); + fail_nth = open(buf, O_RDWR); + for (i = 1;; i++) { + sprintf(buf, "%d", i); + write(fail_nth, buf, strlen(buf)); + res = socketpair(AF_LOCAL, SOCK_STREAM, 0, fds); + err = errno; + pread(fail_nth, buf, sizeof(buf), 0); + if (res == 0) { + close(fds[0]); + close(fds[1]); + } + printf("%d-th fault %c: res=%d/%d\n", i, atoi(buf) ? 'N' : 'Y', + res, err); + if (atoi(buf)) + break; + } + return 0; +} + +An example output: + +1-th fault Y: res=-1/23 +2-th fault Y: res=-1/23 +3-th fault Y: res=-1/12 +4-th fault Y: res=-1/12 +5-th fault Y: res=-1/23 +6-th fault Y: res=-1/23 +7-th fault Y: res=-1/23 +8-th fault Y: res=-1/12 +9-th fault Y: res=-1/12 +10-th fault Y: res=-1/12 +11-th fault Y: res=-1/12 +12-th fault Y: res=-1/12 +13-th fault Y: res=-1/12 +14-th fault Y: res=-1/12 +15-th fault Y: res=-1/12 +16-th fault N: res=0/12 diff --git a/Documentation/filesystems/autofs4.txt b/Documentation/filesystems/autofs4.txt index 8444dc3d57e8..f10dd590f69f 100644 --- a/Documentation/filesystems/autofs4.txt +++ b/Documentation/filesystems/autofs4.txt @@ -316,7 +316,7 @@ For version 5, the format of the message is: struct autofs_v5_packet { int proto_version; /* Protocol version */ int type; /* Type of packet */ - autofs_wqt_t wait_queue_entry_token; + autofs_wqt_t wait_queue_token; __u32 dev; __u64 ino; __u32 uid; @@ -341,12 +341,12 @@ The pipe will be set to "packet mode" (equivalent to passing `O_DIRECT`) to _pipe2(2)_ so that a read from the pipe will return at most one packet, and any unread portion of a packet will be discarded. -The `wait_queue_entry_token` is a unique number which can identify a +The `wait_queue_token` is a unique number which can identify a particular request to be acknowledged. When a message is sent over the pipe the affected dentry is marked as either "active" or "expiring" and other accesses to it block until the message is acknowledged using one of the ioctls below and the relevant -`wait_queue_entry_token`. +`wait_queue_token`. Communicating with autofs: root directory ioctls ------------------------------------------------ @@ -358,7 +358,7 @@ capability, or must be the automount daemon. The available ioctl commands are: - **AUTOFS_IOC_READY**: a notification has been handled. The argument - to the ioctl command is the "wait_queue_entry_token" number + to the ioctl command is the "wait_queue_token" number corresponding to the notification being acknowledged. - **AUTOFS_IOC_FAIL**: similar to above, but indicates failure with the error code `ENOENT`. @@ -382,14 +382,14 @@ The available ioctl commands are: struct autofs_packet_expire_multi { int proto_version; /* Protocol version */ int type; /* Type of packet */ - autofs_wqt_t wait_queue_entry_token; + autofs_wqt_t wait_queue_token; int len; char name[NAME_MAX+1]; }; is required. This is filled in with the name of something that can be unmounted or removed. If nothing can be expired, - `errno` is set to `EAGAIN`. Even though a `wait_queue_entry_token` + `errno` is set to `EAGAIN`. Even though a `wait_queue_token` is present in the structure, no "wait queue" is established and no acknowledgment is needed. - **AUTOFS_IOC_EXPIRE_MULTI**: This is similar to diff --git a/Documentation/filesystems/f2fs.txt b/Documentation/filesystems/f2fs.txt index 4f6531a4701b..273ccb26885e 100644 --- a/Documentation/filesystems/f2fs.txt +++ b/Documentation/filesystems/f2fs.txt @@ -155,11 +155,15 @@ noinline_data Disable the inline data feature, inline data feature is enabled by default. data_flush Enable data flushing before checkpoint in order to persist data of regular and symlink. +fault_injection=%d Enable fault injection in all supported types with + specified injection rate. mode=%s Control block allocation mode which supports "adaptive" and "lfs". In "lfs" mode, there should be no random writes towards main area. io_bits=%u Set the bit size of write IO requests. It should be set with "mode=lfs". +usrquota Enable plain user disk quota accounting. +grpquota Enable plain group disk quota accounting. ================================================================================ DEBUGFS ENTRIES diff --git a/Documentation/filesystems/overlayfs.txt b/Documentation/filesystems/overlayfs.txt index c9e884b52698..36f528a7fdd6 100644 --- a/Documentation/filesystems/overlayfs.txt +++ b/Documentation/filesystems/overlayfs.txt @@ -201,6 +201,40 @@ rightmost one and going left. In the above example lower1 will be the top, lower2 the middle and lower3 the bottom layer. +Sharing and copying layers +-------------------------- + +Lower layers may be shared among several overlay mounts and that is indeed +a very common practice. An overlay mount may use the same lower layer +path as another overlay mount and it may use a lower layer path that is +beneath or above the path of another overlay lower layer path. + +Using an upper layer path and/or a workdir path that are already used by +another overlay mount is not allowed and will fail with EBUSY. Using +partially overlapping paths is not allowed but will not fail with EBUSY. + +Mounting an overlay using an upper layer path, where the upper layer path +was previously used by another mounted overlay in combination with a +different lower layer path, is allowed, unless the "inodes index" feature +is enabled. + +With the "inodes index" feature, on the first time mount, an NFS file +handle of the lower layer root directory, along with the UUID of the lower +filesystem, are encoded and stored in the "trusted.overlay.origin" extended +attribute on the upper layer root directory. On subsequent mount attempts, +the lower root directory file handle and lower filesystem UUID are compared +to the stored origin in upper root directory. On failure to verify the +lower root origin, mount will fail with ESTALE. An overlayfs mount with +"inodes index" enabled will fail with EOPNOTSUPP if the lower filesystem +does not support NFS export, lower filesystem does not have a valid UUID or +if the upper filesystem does not support extended attributes. + +It is quite a common practice to copy overlay layers to a different +directory tree on the same or different underlying filesystem, and even +to a different machine. With the "inodes index" feature, trying to mount +the copied layers will fail the verification of the lower root file handle. + + Non-standard behavior --------------------- diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index 4cddbce85ac9..adba21b5ada7 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -1786,12 +1786,16 @@ pair provide additional information particular to the objects they represent. pos: 0 flags: 02 mnt_id: 9 - tfd: 5 events: 1d data: ffffffffffffffff + tfd: 5 events: 1d data: ffffffffffffffff pos:0 ino:61af sdev:7 where 'tfd' is a target file descriptor number in decimal form, 'events' is events mask being watched and the 'data' is data associated with a target [see epoll(7) for more details]. + The 'pos' is current offset of the target file in decimal form + [see lseek(2)], 'ino' and 'sdev' are inode and device numbers + where target file resides, all in hex format. + Fsnotify files ~~~~~~~~~~~~~~ For inotify files the format is the following diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index 48c9faa73a76..73e7d91f03dc 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -1225,12 +1225,6 @@ The underlying reason for the above rules is to make sure, that a mount can be accurately replicated (e.g. umounting and mounting again) based on the information found in /proc/mounts. -A simple method of saving options at mount/remount time and showing -them is provided with the save_mount_options() and -generic_show_options() helper functions. Please note, that using -these may have drawbacks. For more info see header comments for these -functions in fs/namespace.c. - Resources ========= diff --git a/Documentation/flexible-arrays.txt b/Documentation/flexible-arrays.txt index df904aec9904..a0f2989dd804 100644 --- a/Documentation/flexible-arrays.txt +++ b/Documentation/flexible-arrays.txt @@ -1,6 +1,9 @@ +=================================== Using flexible arrays in the kernel -Last updated for 2.6.32 -Jonathan Corbet <corbet@lwn.net> +=================================== + +:Updated: Last updated for 2.6.32 +:Author: Jonathan Corbet <corbet@lwn.net> Large contiguous memory allocations can be unreliable in the Linux kernel. Kernel programmers will sometimes respond to this problem by allocating @@ -26,7 +29,7 @@ operation. It's also worth noting that flexible arrays do no internal locking at all; if concurrent access to an array is possible, then the caller must arrange for appropriate mutual exclusion. -The creation of a flexible array is done with: +The creation of a flexible array is done with:: #include <linux/flex_array.h> @@ -40,14 +43,14 @@ argument is passed directly to the internal memory allocation calls. With the current code, using flags to ask for high memory is likely to lead to notably unpleasant side effects. -It is also possible to define flexible arrays at compile time with: +It is also possible to define flexible arrays at compile time with:: DEFINE_FLEX_ARRAY(name, element_size, total); This macro will result in a definition of an array with the given name; the element size and total will be checked for validity at compile time. -Storing data into a flexible array is accomplished with a call to: +Storing data into a flexible array is accomplished with a call to:: int flex_array_put(struct flex_array *array, unsigned int element_nr, void *src, gfp_t flags); @@ -63,7 +66,7 @@ running in some sort of atomic context; in this situation, sleeping in the memory allocator would be a bad thing. That can be avoided by using GFP_ATOMIC for the flags value, but, often, there is a better way. The trick is to ensure that any needed memory allocations are done before -entering atomic context, using: +entering atomic context, using:: int flex_array_prealloc(struct flex_array *array, unsigned int start, unsigned int nr_elements, gfp_t flags); @@ -73,7 +76,7 @@ defined by start and nr_elements has been allocated. Thereafter, a flex_array_put() call on an element in that range is guaranteed not to block. -Getting data back out of the array is done with: +Getting data back out of the array is done with:: void *flex_array_get(struct flex_array *fa, unsigned int element_nr); @@ -89,7 +92,7 @@ involving that number probably result from use of unstored array entries. Note that, if array elements are allocated with __GFP_ZERO, they will be initialized to zero and this poisoning will not happen. -Individual elements in the array can be cleared with: +Individual elements in the array can be cleared with:: int flex_array_clear(struct flex_array *array, unsigned int element_nr); @@ -97,7 +100,7 @@ This function will set the given element to FLEX_ARRAY_FREE and return zero. If storage for the indicated element is not allocated for the array, flex_array_clear() will return -EINVAL instead. Note that clearing an element does not release the storage associated with it; to reduce the -allocated size of an array, call: +allocated size of an array, call:: int flex_array_shrink(struct flex_array *array); @@ -106,12 +109,12 @@ This function works by scanning the array for pages containing nothing but FLEX_ARRAY_FREE bytes, so (1) it can be expensive, and (2) it will not work if the array's pages are allocated with __GFP_ZERO. -It is possible to remove all elements of an array with a call to: +It is possible to remove all elements of an array with a call to:: void flex_array_free_parts(struct flex_array *array); This call frees all elements, but leaves the array itself in place. -Freeing the entire array is done with: +Freeing the entire array is done with:: void flex_array_free(struct flex_array *array); diff --git a/Documentation/futex-requeue-pi.txt b/Documentation/futex-requeue-pi.txt index 77b36f59d16b..14ab5787b9a7 100644 --- a/Documentation/futex-requeue-pi.txt +++ b/Documentation/futex-requeue-pi.txt @@ -1,5 +1,6 @@ +================ Futex Requeue PI ----------------- +================ Requeueing of tasks from a non-PI futex to a PI futex requires special handling in order to ensure the underlying rt_mutex is never @@ -20,28 +21,28 @@ implementation would wake the highest-priority waiter, and leave the rest to the natural wakeup inherent in unlocking the mutex associated with the condvar. -Consider the simplified glibc calls: - -/* caller must lock mutex */ -pthread_cond_wait(cond, mutex) -{ - lock(cond->__data.__lock); - unlock(mutex); - do { - unlock(cond->__data.__lock); - futex_wait(cond->__data.__futex); - lock(cond->__data.__lock); - } while(...) - unlock(cond->__data.__lock); - lock(mutex); -} - -pthread_cond_broadcast(cond) -{ - lock(cond->__data.__lock); - unlock(cond->__data.__lock); - futex_requeue(cond->data.__futex, cond->mutex); -} +Consider the simplified glibc calls:: + + /* caller must lock mutex */ + pthread_cond_wait(cond, mutex) + { + lock(cond->__data.__lock); + unlock(mutex); + do { + unlock(cond->__data.__lock); + futex_wait(cond->__data.__futex); + lock(cond->__data.__lock); + } while(...) + unlock(cond->__data.__lock); + lock(mutex); + } + + pthread_cond_broadcast(cond) + { + lock(cond->__data.__lock); + unlock(cond->__data.__lock); + futex_requeue(cond->data.__futex, cond->mutex); + } Once pthread_cond_broadcast() requeues the tasks, the cond->mutex has waiters. Note that pthread_cond_wait() attempts to lock the @@ -53,29 +54,29 @@ In order to support PI-aware pthread_condvar's, the kernel needs to be able to requeue tasks to PI futexes. This support implies that upon a successful futex_wait system call, the caller would return to user space already holding the PI futex. The glibc implementation -would be modified as follows: - - -/* caller must lock mutex */ -pthread_cond_wait_pi(cond, mutex) -{ - lock(cond->__data.__lock); - unlock(mutex); - do { - unlock(cond->__data.__lock); - futex_wait_requeue_pi(cond->__data.__futex); - lock(cond->__data.__lock); - } while(...) - unlock(cond->__data.__lock); - /* the kernel acquired the mutex for us */ -} - -pthread_cond_broadcast_pi(cond) -{ - lock(cond->__data.__lock); - unlock(cond->__data.__lock); - futex_requeue_pi(cond->data.__futex, cond->mutex); -} +would be modified as follows:: + + + /* caller must lock mutex */ + pthread_cond_wait_pi(cond, mutex) + { + lock(cond->__data.__lock); + unlock(mutex); + do { + unlock(cond->__data.__lock); + futex_wait_requeue_pi(cond->__data.__futex); + lock(cond->__data.__lock); + } while(...) + unlock(cond->__data.__lock); + /* the kernel acquired the mutex for us */ + } + + pthread_cond_broadcast_pi(cond) + { + lock(cond->__data.__lock); + unlock(cond->__data.__lock); + futex_requeue_pi(cond->data.__futex, cond->mutex); + } The actual glibc implementation will likely test for PI and make the necessary changes inside the existing calls rather than creating new diff --git a/Documentation/gcc-plugins.txt b/Documentation/gcc-plugins.txt index 433eaefb4aa1..8502f24396fb 100644 --- a/Documentation/gcc-plugins.txt +++ b/Documentation/gcc-plugins.txt @@ -1,14 +1,15 @@ +========================= GCC plugin infrastructure ========================= -1. Introduction -=============== +Introduction +============ GCC plugins are loadable modules that provide extra features to the -compiler [1]. They are useful for runtime instrumentation and static analysis. +compiler [1]_. They are useful for runtime instrumentation and static analysis. We can analyse, change and add further code during compilation via -callbacks [2], GIMPLE [3], IPA [4] and RTL passes [5]. +callbacks [2]_, GIMPLE [3]_, IPA [4]_ and RTL passes [5]_. The GCC plugin infrastructure of the kernel supports all gcc versions from 4.5 to 6.0, building out-of-tree modules, cross-compilation and building in a @@ -21,56 +22,61 @@ and versions 4.8+ can only be compiled by a C++ compiler. Currently the GCC plugin infrastructure supports only the x86, arm, arm64 and powerpc architectures. -This infrastructure was ported from grsecurity [6] and PaX [7]. +This infrastructure was ported from grsecurity [6]_ and PaX [7]_. -- -[1] https://gcc.gnu.org/onlinedocs/gccint/Plugins.html -[2] https://gcc.gnu.org/onlinedocs/gccint/Plugin-API.html#Plugin-API -[3] https://gcc.gnu.org/onlinedocs/gccint/GIMPLE.html -[4] https://gcc.gnu.org/onlinedocs/gccint/IPA.html -[5] https://gcc.gnu.org/onlinedocs/gccint/RTL.html -[6] https://grsecurity.net/ -[7] https://pax.grsecurity.net/ +.. [1] https://gcc.gnu.org/onlinedocs/gccint/Plugins.html +.. [2] https://gcc.gnu.org/onlinedocs/gccint/Plugin-API.html#Plugin-API +.. [3] https://gcc.gnu.org/onlinedocs/gccint/GIMPLE.html +.. [4] https://gcc.gnu.org/onlinedocs/gccint/IPA.html +.. [5] https://gcc.gnu.org/onlinedocs/gccint/RTL.html +.. [6] https://grsecurity.net/ +.. [7] https://pax.grsecurity.net/ + + +Files +===== -2. Files -======== +**$(src)/scripts/gcc-plugins** -$(src)/scripts/gcc-plugins This is the directory of the GCC plugins. -$(src)/scripts/gcc-plugins/gcc-common.h +**$(src)/scripts/gcc-plugins/gcc-common.h** + This is a compatibility header for GCC plugins. It should be always included instead of individual gcc headers. -$(src)/scripts/gcc-plugin.sh +**$(src)/scripts/gcc-plugin.sh** + This script checks the availability of the included headers in gcc-common.h and chooses the proper host compiler to build the plugins (gcc-4.7 can be built by either gcc or g++). -$(src)/scripts/gcc-plugins/gcc-generate-gimple-pass.h -$(src)/scripts/gcc-plugins/gcc-generate-ipa-pass.h -$(src)/scripts/gcc-plugins/gcc-generate-simple_ipa-pass.h -$(src)/scripts/gcc-plugins/gcc-generate-rtl-pass.h +**$(src)/scripts/gcc-plugins/gcc-generate-gimple-pass.h, +$(src)/scripts/gcc-plugins/gcc-generate-ipa-pass.h, +$(src)/scripts/gcc-plugins/gcc-generate-simple_ipa-pass.h, +$(src)/scripts/gcc-plugins/gcc-generate-rtl-pass.h** + These headers automatically generate the registration structures for GIMPLE, SIMPLE_IPA, IPA and RTL passes. They support all gcc versions from 4.5 to 6.0. They should be preferred to creating the structures by hand. -3. Usage -======== +Usage +===== You must install the gcc plugin headers for your gcc version, -e.g., on Ubuntu for gcc-4.9: +e.g., on Ubuntu for gcc-4.9:: apt-get install gcc-4.9-plugin-dev -Enable a GCC plugin based feature in the kernel config: +Enable a GCC plugin based feature in the kernel config:: CONFIG_GCC_PLUGIN_CYC_COMPLEXITY = y -To compile only the plugin(s): +To compile only the plugin(s):: make gcc-plugins diff --git a/Documentation/highuid.txt b/Documentation/highuid.txt index 6bad6f1d1cac..6ee70465c0ea 100644 --- a/Documentation/highuid.txt +++ b/Documentation/highuid.txt @@ -1,4 +1,9 @@ -Notes on the change from 16-bit UIDs to 32-bit UIDs: +=================================================== +Notes on the change from 16-bit UIDs to 32-bit UIDs +=================================================== + +:Author: Chris Wing <wingc@umich.edu> +:Last updated: January 11, 2000 - kernel code MUST take into account __kernel_uid_t and __kernel_uid32_t when communicating between user and kernel space in an ioctl or data @@ -28,30 +33,34 @@ What's left to be done for 32-bit UIDs on all Linux architectures: uses the 32-bit UID system calls properly otherwise. This affects at least: - iBCS on Intel - sparc32 emulation on sparc64 - (need to support whatever new 32-bit UID system calls are added to - sparc32) + - iBCS on Intel + + - sparc32 emulation on sparc64 + (need to support whatever new 32-bit UID system calls are added to + sparc32) - Validate that all filesystems behave properly. At present, 32-bit UIDs _should_ work for: - ext2 - ufs - isofs - nfs - coda - udf + + - ext2 + - ufs + - isofs + - nfs + - coda + - udf Ioctl() fixups have been made for: - ncpfs - smbfs + + - ncpfs + - smbfs Filesystems with simple fixups to prevent 16-bit UID wraparound: - minix - sysv - qnx4 + + - minix + - sysv + - qnx4 Other filesystems have not been checked yet. @@ -69,9 +78,3 @@ What's left to be done for 32-bit UIDs on all Linux architectures: - make sure that the UID mapping feature of AX25 networking works properly (it should be safe because it's always used a 32-bit integer to communicate between user and kernel) - - -Chris Wing -wingc@umich.edu - -last updated: January 11, 2000 diff --git a/Documentation/hw_random.txt b/Documentation/hw_random.txt index fce1634907d0..121de96e395e 100644 --- a/Documentation/hw_random.txt +++ b/Documentation/hw_random.txt @@ -1,90 +1,105 @@ -Introduction: - - The hw_random framework is software that makes use of a - special hardware feature on your CPU or motherboard, - a Random Number Generator (RNG). The software has two parts: - a core providing the /dev/hwrng character device and its - sysfs support, plus a hardware-specific driver that plugs - into that core. - - To make the most effective use of these mechanisms, you - should download the support software as well. Download the - latest version of the "rng-tools" package from the - hw_random driver's official Web site: - - http://sourceforge.net/projects/gkernel/ - - Those tools use /dev/hwrng to fill the kernel entropy pool, - which is used internally and exported by the /dev/urandom and - /dev/random special files. - -Theory of operation: - - CHARACTER DEVICE. Using the standard open() - and read() system calls, you can read random data from - the hardware RNG device. This data is NOT CHECKED by any - fitness tests, and could potentially be bogus (if the - hardware is faulty or has been tampered with). Data is only - output if the hardware "has-data" flag is set, but nevertheless - a security-conscious person would run fitness tests on the - data before assuming it is truly random. - - The rng-tools package uses such tests in "rngd", and lets you - run them by hand with a "rngtest" utility. - - /dev/hwrng is char device major 10, minor 183. - - CLASS DEVICE. There is a /sys/class/misc/hw_random node with - two unique attributes, "rng_available" and "rng_current". The - "rng_available" attribute lists the hardware-specific drivers - available, while "rng_current" lists the one which is currently - connected to /dev/hwrng. If your system has more than one - RNG available, you may change the one used by writing a name from - the list in "rng_available" into "rng_current". +========================================================== +Linux support for random number generator in i8xx chipsets +========================================================== + +Introduction +============ + +The hw_random framework is software that makes use of a +special hardware feature on your CPU or motherboard, +a Random Number Generator (RNG). The software has two parts: +a core providing the /dev/hwrng character device and its +sysfs support, plus a hardware-specific driver that plugs +into that core. + +To make the most effective use of these mechanisms, you +should download the support software as well. Download the +latest version of the "rng-tools" package from the +hw_random driver's official Web site: + + http://sourceforge.net/projects/gkernel/ + +Those tools use /dev/hwrng to fill the kernel entropy pool, +which is used internally and exported by the /dev/urandom and +/dev/random special files. + +Theory of operation +=================== + +CHARACTER DEVICE. Using the standard open() +and read() system calls, you can read random data from +the hardware RNG device. This data is NOT CHECKED by any +fitness tests, and could potentially be bogus (if the +hardware is faulty or has been tampered with). Data is only +output if the hardware "has-data" flag is set, but nevertheless +a security-conscious person would run fitness tests on the +data before assuming it is truly random. + +The rng-tools package uses such tests in "rngd", and lets you +run them by hand with a "rngtest" utility. + +/dev/hwrng is char device major 10, minor 183. + +CLASS DEVICE. There is a /sys/class/misc/hw_random node with +two unique attributes, "rng_available" and "rng_current". The +"rng_available" attribute lists the hardware-specific drivers +available, while "rng_current" lists the one which is currently +connected to /dev/hwrng. If your system has more than one +RNG available, you may change the one used by writing a name from +the list in "rng_available" into "rng_current". ========================================================================== - Hardware driver for Intel/AMD/VIA Random Number Generators (RNG) - Copyright 2000,2001 Jeff Garzik <jgarzik@pobox.com> - Copyright 2000,2001 Philipp Rumpf <prumpf@mandrakesoft.com> +Hardware driver for Intel/AMD/VIA Random Number Generators (RNG) + - Copyright 2000,2001 Jeff Garzik <jgarzik@pobox.com> + - Copyright 2000,2001 Philipp Rumpf <prumpf@mandrakesoft.com> -About the Intel RNG hardware, from the firmware hub datasheet: - The Firmware Hub integrates a Random Number Generator (RNG) - using thermal noise generated from inherently random quantum - mechanical properties of silicon. When not generating new random - bits the RNG circuitry will enter a low power state. Intel will - provide a binary software driver to give third party software - access to our RNG for use as a security feature. At this time, - the RNG is only to be used with a system in an OS-present state. +About the Intel RNG hardware, from the firmware hub datasheet +============================================================= -Intel RNG Driver notes: +The Firmware Hub integrates a Random Number Generator (RNG) +using thermal noise generated from inherently random quantum +mechanical properties of silicon. When not generating new random +bits the RNG circuitry will enter a low power state. Intel will +provide a binary software driver to give third party software +access to our RNG for use as a security feature. At this time, +the RNG is only to be used with a system in an OS-present state. - * FIXME: support poll(2) +Intel RNG Driver notes +====================== - NOTE: request_mem_region was removed, for three reasons: - 1) Only one RNG is supported by this driver, 2) The location - used by the RNG is a fixed location in MMIO-addressable memory, +FIXME: support poll(2) + +.. note:: + + request_mem_region was removed, for three reasons: + + 1) Only one RNG is supported by this driver; + 2) The location used by the RNG is a fixed location in + MMIO-addressable memory; 3) users with properly working BIOS e820 handling will always - have the region in which the RNG is located reserved, so - request_mem_region calls always fail for proper setups. - However, for people who use mem=XX, BIOS e820 information is - -not- in /proc/iomem, and request_mem_region(RNG_ADDR) can - succeed. + have the region in which the RNG is located reserved, so + request_mem_region calls always fail for proper setups. + However, for people who use mem=XX, BIOS e820 information is + **not** in /proc/iomem, and request_mem_region(RNG_ADDR) can + succeed. -Driver details: +Driver details +============== - Based on: +Based on: Intel 82802AB/82802AC Firmware Hub (FWH) Datasheet - May 1999 Order Number: 290658-002 R + May 1999 Order Number: 290658-002 R - Intel 82802 Firmware Hub: Random Number Generator +Intel 82802 Firmware Hub: + Random Number Generator Programmer's Reference Manual - December 1999 Order Number: 298029-001 R + December 1999 Order Number: 298029-001 R - Intel 82802 Firmware HUB Random Number Generator Driver +Intel 82802 Firmware HUB Random Number Generator Driver Copyright (c) 2000 Matt Sottek <msottek@quiknet.com> - Special thanks to Matt Sottek. I did the "guts", he - did the "brains" and all the testing. +Special thanks to Matt Sottek. I did the "guts", he +did the "brains" and all the testing. diff --git a/Documentation/hwspinlock.txt b/Documentation/hwspinlock.txt index 61c1ee98e59f..ed640a278185 100644 --- a/Documentation/hwspinlock.txt +++ b/Documentation/hwspinlock.txt @@ -1,6 +1,9 @@ +=========================== Hardware Spinlock Framework +=========================== -1. Introduction +Introduction +============ Hardware spinlock modules provide hardware assistance for synchronization and mutual exclusion between heterogeneous processors and those not operating @@ -32,286 +35,370 @@ structure). A common hwspinlock interface makes it possible to have generic, platform- independent, drivers. -2. User API +User API +======== + +:: struct hwspinlock *hwspin_lock_request(void); - - dynamically assign an hwspinlock and return its address, or NULL - in case an unused hwspinlock isn't available. Users of this - API will usually want to communicate the lock's id to the remote core - before it can be used to achieve synchronization. - Should be called from a process context (might sleep). + +Dynamically assign an hwspinlock and return its address, or NULL +in case an unused hwspinlock isn't available. Users of this +API will usually want to communicate the lock's id to the remote core +before it can be used to achieve synchronization. + +Should be called from a process context (might sleep). + +:: struct hwspinlock *hwspin_lock_request_specific(unsigned int id); - - assign a specific hwspinlock id and return its address, or NULL - if that hwspinlock is already in use. Usually board code will - be calling this function in order to reserve specific hwspinlock - ids for predefined purposes. - Should be called from a process context (might sleep). + +Assign a specific hwspinlock id and return its address, or NULL +if that hwspinlock is already in use. Usually board code will +be calling this function in order to reserve specific hwspinlock +ids for predefined purposes. + +Should be called from a process context (might sleep). + +:: int of_hwspin_lock_get_id(struct device_node *np, int index); - - retrieve the global lock id for an OF phandle-based specific lock. - This function provides a means for DT users of a hwspinlock module - to get the global lock id of a specific hwspinlock, so that it can - be requested using the normal hwspin_lock_request_specific() API. - The function returns a lock id number on success, -EPROBE_DEFER if - the hwspinlock device is not yet registered with the core, or other - error values. - Should be called from a process context (might sleep). + +Retrieve the global lock id for an OF phandle-based specific lock. +This function provides a means for DT users of a hwspinlock module +to get the global lock id of a specific hwspinlock, so that it can +be requested using the normal hwspin_lock_request_specific() API. + +The function returns a lock id number on success, -EPROBE_DEFER if +the hwspinlock device is not yet registered with the core, or other +error values. + +Should be called from a process context (might sleep). + +:: int hwspin_lock_free(struct hwspinlock *hwlock); - - free a previously-assigned hwspinlock; returns 0 on success, or an - appropriate error code on failure (e.g. -EINVAL if the hwspinlock - is already free). - Should be called from a process context (might sleep). + +Free a previously-assigned hwspinlock; returns 0 on success, or an +appropriate error code on failure (e.g. -EINVAL if the hwspinlock +is already free). + +Should be called from a process context (might sleep). + +:: int hwspin_lock_timeout(struct hwspinlock *hwlock, unsigned int timeout); - - lock a previously-assigned hwspinlock with a timeout limit (specified in - msecs). If the hwspinlock is already taken, the function will busy loop - waiting for it to be released, but give up when the timeout elapses. - Upon a successful return from this function, preemption is disabled so - the caller must not sleep, and is advised to release the hwspinlock as - soon as possible, in order to minimize remote cores polling on the - hardware interconnect. - Returns 0 when successful and an appropriate error code otherwise (most - notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs). - The function will never sleep. + +Lock a previously-assigned hwspinlock with a timeout limit (specified in +msecs). If the hwspinlock is already taken, the function will busy loop +waiting for it to be released, but give up when the timeout elapses. +Upon a successful return from this function, preemption is disabled so +the caller must not sleep, and is advised to release the hwspinlock as +soon as possible, in order to minimize remote cores polling on the +hardware interconnect. + +Returns 0 when successful and an appropriate error code otherwise (most +notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs). +The function will never sleep. + +:: int hwspin_lock_timeout_irq(struct hwspinlock *hwlock, unsigned int timeout); - - lock a previously-assigned hwspinlock with a timeout limit (specified in - msecs). If the hwspinlock is already taken, the function will busy loop - waiting for it to be released, but give up when the timeout elapses. - Upon a successful return from this function, preemption and the local - interrupts are disabled, so the caller must not sleep, and is advised to - release the hwspinlock as soon as possible. - Returns 0 when successful and an appropriate error code otherwise (most - notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs). - The function will never sleep. + +Lock a previously-assigned hwspinlock with a timeout limit (specified in +msecs). If the hwspinlock is already taken, the function will busy loop +waiting for it to be released, but give up when the timeout elapses. +Upon a successful return from this function, preemption and the local +interrupts are disabled, so the caller must not sleep, and is advised to +release the hwspinlock as soon as possible. + +Returns 0 when successful and an appropriate error code otherwise (most +notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs). +The function will never sleep. + +:: int hwspin_lock_timeout_irqsave(struct hwspinlock *hwlock, unsigned int to, - unsigned long *flags); - - lock a previously-assigned hwspinlock with a timeout limit (specified in - msecs). If the hwspinlock is already taken, the function will busy loop - waiting for it to be released, but give up when the timeout elapses. - Upon a successful return from this function, preemption is disabled, - local interrupts are disabled and their previous state is saved at the - given flags placeholder. The caller must not sleep, and is advised to - release the hwspinlock as soon as possible. - Returns 0 when successful and an appropriate error code otherwise (most - notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs). - The function will never sleep. + unsigned long *flags); + +Lock a previously-assigned hwspinlock with a timeout limit (specified in +msecs). If the hwspinlock is already taken, the function will busy loop +waiting for it to be released, but give up when the timeout elapses. +Upon a successful return from this function, preemption is disabled, +local interrupts are disabled and their previous state is saved at the +given flags placeholder. The caller must not sleep, and is advised to +release the hwspinlock as soon as possible. + +Returns 0 when successful and an appropriate error code otherwise (most +notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs). + +The function will never sleep. + +:: int hwspin_trylock(struct hwspinlock *hwlock); - - attempt to lock a previously-assigned hwspinlock, but immediately fail if - it is already taken. - Upon a successful return from this function, preemption is disabled so - caller must not sleep, and is advised to release the hwspinlock as soon as - possible, in order to minimize remote cores polling on the hardware - interconnect. - Returns 0 on success and an appropriate error code otherwise (most - notably -EBUSY if the hwspinlock was already taken). - The function will never sleep. + + +Attempt to lock a previously-assigned hwspinlock, but immediately fail if +it is already taken. + +Upon a successful return from this function, preemption is disabled so +caller must not sleep, and is advised to release the hwspinlock as soon as +possible, in order to minimize remote cores polling on the hardware +interconnect. + +Returns 0 on success and an appropriate error code otherwise (most +notably -EBUSY if the hwspinlock was already taken). +The function will never sleep. + +:: int hwspin_trylock_irq(struct hwspinlock *hwlock); - - attempt to lock a previously-assigned hwspinlock, but immediately fail if - it is already taken. - Upon a successful return from this function, preemption and the local - interrupts are disabled so caller must not sleep, and is advised to - release the hwspinlock as soon as possible. - Returns 0 on success and an appropriate error code otherwise (most - notably -EBUSY if the hwspinlock was already taken). - The function will never sleep. + + +Attempt to lock a previously-assigned hwspinlock, but immediately fail if +it is already taken. + +Upon a successful return from this function, preemption and the local +interrupts are disabled so caller must not sleep, and is advised to +release the hwspinlock as soon as possible. + +Returns 0 on success and an appropriate error code otherwise (most +notably -EBUSY if the hwspinlock was already taken). + +The function will never sleep. + +:: int hwspin_trylock_irqsave(struct hwspinlock *hwlock, unsigned long *flags); - - attempt to lock a previously-assigned hwspinlock, but immediately fail if - it is already taken. - Upon a successful return from this function, preemption is disabled, - the local interrupts are disabled and their previous state is saved - at the given flags placeholder. The caller must not sleep, and is advised - to release the hwspinlock as soon as possible. - Returns 0 on success and an appropriate error code otherwise (most - notably -EBUSY if the hwspinlock was already taken). - The function will never sleep. + +Attempt to lock a previously-assigned hwspinlock, but immediately fail if +it is already taken. + +Upon a successful return from this function, preemption is disabled, +the local interrupts are disabled and their previous state is saved +at the given flags placeholder. The caller must not sleep, and is advised +to release the hwspinlock as soon as possible. + +Returns 0 on success and an appropriate error code otherwise (most +notably -EBUSY if the hwspinlock was already taken). +The function will never sleep. + +:: void hwspin_unlock(struct hwspinlock *hwlock); - - unlock a previously-locked hwspinlock. Always succeed, and can be called - from any context (the function never sleeps). Note: code should _never_ - unlock an hwspinlock which is already unlocked (there is no protection - against this). + +Unlock a previously-locked hwspinlock. Always succeed, and can be called +from any context (the function never sleeps). + +.. note:: + + code should **never** unlock an hwspinlock which is already unlocked + (there is no protection against this). + +:: void hwspin_unlock_irq(struct hwspinlock *hwlock); - - unlock a previously-locked hwspinlock and enable local interrupts. - The caller should _never_ unlock an hwspinlock which is already unlocked. - Doing so is considered a bug (there is no protection against this). - Upon a successful return from this function, preemption and local - interrupts are enabled. This function will never sleep. + +Unlock a previously-locked hwspinlock and enable local interrupts. +The caller should **never** unlock an hwspinlock which is already unlocked. + +Doing so is considered a bug (there is no protection against this). +Upon a successful return from this function, preemption and local +interrupts are enabled. This function will never sleep. + +:: void hwspin_unlock_irqrestore(struct hwspinlock *hwlock, unsigned long *flags); - - unlock a previously-locked hwspinlock. - The caller should _never_ unlock an hwspinlock which is already unlocked. - Doing so is considered a bug (there is no protection against this). - Upon a successful return from this function, preemption is reenabled, - and the state of the local interrupts is restored to the state saved at - the given flags. This function will never sleep. + +Unlock a previously-locked hwspinlock. + +The caller should **never** unlock an hwspinlock which is already unlocked. +Doing so is considered a bug (there is no protection against this). +Upon a successful return from this function, preemption is reenabled, +and the state of the local interrupts is restored to the state saved at +the given flags. This function will never sleep. + +:: int hwspin_lock_get_id(struct hwspinlock *hwlock); - - retrieve id number of a given hwspinlock. This is needed when an - hwspinlock is dynamically assigned: before it can be used to achieve - mutual exclusion with a remote cpu, the id number should be communicated - to the remote task with which we want to synchronize. - Returns the hwspinlock id number, or -EINVAL if hwlock is null. - -3. Typical usage - -#include <linux/hwspinlock.h> -#include <linux/err.h> - -int hwspinlock_example1(void) -{ - struct hwspinlock *hwlock; - int ret; - - /* dynamically assign a hwspinlock */ - hwlock = hwspin_lock_request(); - if (!hwlock) - ... - - id = hwspin_lock_get_id(hwlock); - /* probably need to communicate id to a remote processor now */ - - /* take the lock, spin for 1 sec if it's already taken */ - ret = hwspin_lock_timeout(hwlock, 1000); - if (ret) - ... - - /* - * we took the lock, do our thing now, but do NOT sleep - */ - - /* release the lock */ - hwspin_unlock(hwlock); - - /* free the lock */ - ret = hwspin_lock_free(hwlock); - if (ret) - ... - - return ret; -} - -int hwspinlock_example2(void) -{ - struct hwspinlock *hwlock; - int ret; - - /* - * assign a specific hwspinlock id - this should be called early - * by board init code. - */ - hwlock = hwspin_lock_request_specific(PREDEFINED_LOCK_ID); - if (!hwlock) - ... - - /* try to take it, but don't spin on it */ - ret = hwspin_trylock(hwlock); - if (!ret) { - pr_info("lock is already taken\n"); - return -EBUSY; - } - /* - * we took the lock, do our thing now, but do NOT sleep - */ +Retrieve id number of a given hwspinlock. This is needed when an +hwspinlock is dynamically assigned: before it can be used to achieve +mutual exclusion with a remote cpu, the id number should be communicated +to the remote task with which we want to synchronize. + +Returns the hwspinlock id number, or -EINVAL if hwlock is null. + +Typical usage +============= - /* release the lock */ - hwspin_unlock(hwlock); +:: - /* free the lock */ - ret = hwspin_lock_free(hwlock); - if (ret) - ... + #include <linux/hwspinlock.h> + #include <linux/err.h> - return ret; -} + int hwspinlock_example1(void) + { + struct hwspinlock *hwlock; + int ret; + /* dynamically assign a hwspinlock */ + hwlock = hwspin_lock_request(); + if (!hwlock) + ... -4. API for implementors + id = hwspin_lock_get_id(hwlock); + /* probably need to communicate id to a remote processor now */ + + /* take the lock, spin for 1 sec if it's already taken */ + ret = hwspin_lock_timeout(hwlock, 1000); + if (ret) + ... + + /* + * we took the lock, do our thing now, but do NOT sleep + */ + + /* release the lock */ + hwspin_unlock(hwlock); + + /* free the lock */ + ret = hwspin_lock_free(hwlock); + if (ret) + ... + + return ret; + } + + int hwspinlock_example2(void) + { + struct hwspinlock *hwlock; + int ret; + + /* + * assign a specific hwspinlock id - this should be called early + * by board init code. + */ + hwlock = hwspin_lock_request_specific(PREDEFINED_LOCK_ID); + if (!hwlock) + ... + + /* try to take it, but don't spin on it */ + ret = hwspin_trylock(hwlock); + if (!ret) { + pr_info("lock is already taken\n"); + return -EBUSY; + } + + /* + * we took the lock, do our thing now, but do NOT sleep + */ + + /* release the lock */ + hwspin_unlock(hwlock); + + /* free the lock */ + ret = hwspin_lock_free(hwlock); + if (ret) + ... + + return ret; + } + + +API for implementors +==================== + +:: int hwspin_lock_register(struct hwspinlock_device *bank, struct device *dev, const struct hwspinlock_ops *ops, int base_id, int num_locks); - - to be called from the underlying platform-specific implementation, in - order to register a new hwspinlock device (which is usually a bank of - numerous locks). Should be called from a process context (this function - might sleep). - Returns 0 on success, or appropriate error code on failure. + +To be called from the underlying platform-specific implementation, in +order to register a new hwspinlock device (which is usually a bank of +numerous locks). Should be called from a process context (this function +might sleep). + +Returns 0 on success, or appropriate error code on failure. + +:: int hwspin_lock_unregister(struct hwspinlock_device *bank); - - to be called from the underlying vendor-specific implementation, in order - to unregister an hwspinlock device (which is usually a bank of numerous - locks). - Should be called from a process context (this function might sleep). - Returns the address of hwspinlock on success, or NULL on error (e.g. - if the hwspinlock is still in use). -5. Important structs +To be called from the underlying vendor-specific implementation, in order +to unregister an hwspinlock device (which is usually a bank of numerous +locks). + +Should be called from a process context (this function might sleep). + +Returns the address of hwspinlock on success, or NULL on error (e.g. +if the hwspinlock is still in use). + +Important structs +================= struct hwspinlock_device is a device which usually contains a bank of hardware locks. It is registered by the underlying hwspinlock implementation using the hwspin_lock_register() API. -/** - * struct hwspinlock_device - a device which usually spans numerous hwspinlocks - * @dev: underlying device, will be used to invoke runtime PM api - * @ops: platform-specific hwspinlock handlers - * @base_id: id index of the first lock in this device - * @num_locks: number of locks in this device - * @lock: dynamically allocated array of 'struct hwspinlock' - */ -struct hwspinlock_device { - struct device *dev; - const struct hwspinlock_ops *ops; - int base_id; - int num_locks; - struct hwspinlock lock[0]; -}; +:: + + /** + * struct hwspinlock_device - a device which usually spans numerous hwspinlocks + * @dev: underlying device, will be used to invoke runtime PM api + * @ops: platform-specific hwspinlock handlers + * @base_id: id index of the first lock in this device + * @num_locks: number of locks in this device + * @lock: dynamically allocated array of 'struct hwspinlock' + */ + struct hwspinlock_device { + struct device *dev; + const struct hwspinlock_ops *ops; + int base_id; + int num_locks; + struct hwspinlock lock[0]; + }; struct hwspinlock_device contains an array of hwspinlock structs, each -of which represents a single hardware lock: - -/** - * struct hwspinlock - this struct represents a single hwspinlock instance - * @bank: the hwspinlock_device structure which owns this lock - * @lock: initialized and used by hwspinlock core - * @priv: private data, owned by the underlying platform-specific hwspinlock drv - */ -struct hwspinlock { - struct hwspinlock_device *bank; - spinlock_t lock; - void *priv; -}; +of which represents a single hardware lock:: + + /** + * struct hwspinlock - this struct represents a single hwspinlock instance + * @bank: the hwspinlock_device structure which owns this lock + * @lock: initialized and used by hwspinlock core + * @priv: private data, owned by the underlying platform-specific hwspinlock drv + */ + struct hwspinlock { + struct hwspinlock_device *bank; + spinlock_t lock; + void *priv; + }; When registering a bank of locks, the hwspinlock driver only needs to set the priv members of the locks. The rest of the members are set and initialized by the hwspinlock core itself. -6. Implementation callbacks +Implementation callbacks +======================== -There are three possible callbacks defined in 'struct hwspinlock_ops': +There are three possible callbacks defined in 'struct hwspinlock_ops':: -struct hwspinlock_ops { - int (*trylock)(struct hwspinlock *lock); - void (*unlock)(struct hwspinlock *lock); - void (*relax)(struct hwspinlock *lock); -}; + struct hwspinlock_ops { + int (*trylock)(struct hwspinlock *lock); + void (*unlock)(struct hwspinlock *lock); + void (*relax)(struct hwspinlock *lock); + }; The first two callbacks are mandatory: The ->trylock() callback should make a single attempt to take the lock, and -return 0 on failure and 1 on success. This callback may _not_ sleep. +return 0 on failure and 1 on success. This callback may **not** sleep. The ->unlock() callback releases the lock. It always succeed, and it, too, -may _not_ sleep. +may **not** sleep. The ->relax() callback is optional. It is called by hwspinlock core while spinning on a lock, and can be used by the underlying implementation to force -a delay between two successive invocations of ->trylock(). It may _not_ sleep. +a delay between two successive invocations of ->trylock(). It may **not** sleep. diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index 820d9040de16..0500193434cb 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -34,6 +34,8 @@ Supported adapters: * Intel Broxton (SOC) * Intel Lewisburg (PCH) * Intel Gemini Lake (SOC) + * Intel Cannon Lake-H (PCH) + * Intel Cannon Lake-LP (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/i2c/dev-interface b/Documentation/i2c/dev-interface index bcf919d8625c..5ff19447ac44 100644 --- a/Documentation/i2c/dev-interface +++ b/Documentation/i2c/dev-interface @@ -191,7 +191,7 @@ checking on future transactions.) 4* Other ioctl() calls are converted to in-kernel function calls by i2c-dev. Examples include I2C_FUNCS, which queries the I2C adapter functionality using i2c.h:i2c_get_functionality(), and I2C_SMBUS, which -performs an SMBus transaction using i2c-core.c:i2c_smbus_xfer(). +performs an SMBus transaction using i2c-core-smbus.c:i2c_smbus_xfer(). The i2c-dev driver is responsible for checking all the parameters that come from user-space for validity. After this point, there is no @@ -200,13 +200,13 @@ and calls that would have been performed by kernel I2C chip drivers directly. This means that I2C bus drivers don't need to implement anything special to support access from user-space. -5* These i2c-core.c/i2c.h functions are wrappers to the actual -implementation of your I2C bus driver. Each adapter must declare -callback functions implementing these standard calls. -i2c.h:i2c_get_functionality() calls i2c_adapter.algo->functionality(), -while i2c-core.c:i2c_smbus_xfer() calls either +5* These i2c.h functions are wrappers to the actual implementation of +your I2C bus driver. Each adapter must declare callback functions +implementing these standard calls. i2c.h:i2c_get_functionality() calls +i2c_adapter.algo->functionality(), while +i2c-core-smbus.c:i2c_smbus_xfer() calls either adapter.algo->smbus_xfer() if it is implemented, or if not, -i2c-core.c:i2c_smbus_xfer_emulated() which in turn calls +i2c-core-smbus.c:i2c_smbus_xfer_emulated() which in turn calls i2c_adapter.algo->master_xfer(). After your I2C bus driver has processed these requests, execution runs diff --git a/Documentation/input/index.rst b/Documentation/input/index.rst index 7a3e71c2bd00..9888f5cbf6d5 100644 --- a/Documentation/input/index.rst +++ b/Documentation/input/index.rst @@ -6,7 +6,6 @@ Contents: .. toctree:: :maxdepth: 2 - :numbered: input_uapi input_kapi diff --git a/Documentation/intel_txt.txt b/Documentation/intel_txt.txt index 91d89c540709..d83c1a2122c9 100644 --- a/Documentation/intel_txt.txt +++ b/Documentation/intel_txt.txt @@ -1,4 +1,5 @@ -Intel(R) TXT Overview: +===================== +Intel(R) TXT Overview ===================== Intel's technology for safer computing, Intel(R) Trusted Execution @@ -8,9 +9,10 @@ provide the building blocks for creating trusted platforms. Intel TXT was formerly known by the code name LaGrande Technology (LT). Intel TXT in Brief: -o Provides dynamic root of trust for measurement (DRTM) -o Data protection in case of improper shutdown -o Measurement and verification of launched environment + +- Provides dynamic root of trust for measurement (DRTM) +- Data protection in case of improper shutdown +- Measurement and verification of launched environment Intel TXT is part of the vPro(TM) brand and is also available some non-vPro systems. It is currently available on desktop systems @@ -24,16 +26,21 @@ which has been updated for the new released platforms. Intel TXT has been presented at various events over the past few years, some of which are: - LinuxTAG 2008: + + - LinuxTAG 2008: http://www.linuxtag.org/2008/en/conf/events/vp-donnerstag.html - TRUST2008: + + - TRUST2008: http://www.trust-conference.eu/downloads/Keynote-Speakers/ 3_David-Grawrock_The-Front-Door-of-Trusted-Computing.pdf - IDF, Shanghai: + + - IDF, Shanghai: http://www.prcidf.com.cn/index_en.html - IDFs 2006, 2007 (I'm not sure if/where they are online) -Trusted Boot Project Overview: + - IDFs 2006, 2007 + (I'm not sure if/where they are online) + +Trusted Boot Project Overview ============================= Trusted Boot (tboot) is an open source, pre-kernel/VMM module that @@ -87,11 +94,12 @@ Intel-provided firmware). How Does it Work? ================= -o Tboot is an executable that is launched by the bootloader as +- Tboot is an executable that is launched by the bootloader as the "kernel" (the binary the bootloader executes). -o It performs all of the work necessary to determine if the +- It performs all of the work necessary to determine if the platform supports Intel TXT and, if so, executes the GETSEC[SENTER] processor instruction that initiates the dynamic root of trust. + - If tboot determines that the system does not support Intel TXT or is not configured correctly (e.g. the SINIT AC Module was incorrect), it will directly launch the kernel with no changes @@ -99,12 +107,14 @@ o It performs all of the work necessary to determine if the - Tboot will output various information about its progress to the terminal, serial port, and/or an in-memory log; the output locations can be configured with a command line switch. -o The GETSEC[SENTER] instruction will return control to tboot and + +- The GETSEC[SENTER] instruction will return control to tboot and tboot then verifies certain aspects of the environment (e.g. TPM NV lock, e820 table does not have invalid entries, etc.). -o It will wake the APs from the special sleep state the GETSEC[SENTER] +- It will wake the APs from the special sleep state the GETSEC[SENTER] instruction had put them in and place them into a wait-for-SIPI state. + - Because the processors will not respond to an INIT or SIPI when in the TXT environment, it is necessary to create a small VT-x guest for the APs. When they run in this guest, they will @@ -112,8 +122,10 @@ o It will wake the APs from the special sleep state the GETSEC[SENTER] VMEXITs, and then disable VT and jump to the SIPI vector. This approach seemed like a better choice than having to insert special code into the kernel's MP wakeup sequence. -o Tboot then applies an (optional) user-defined launch policy to + +- Tboot then applies an (optional) user-defined launch policy to verify the kernel and initrd. + - This policy is rooted in TPM NV and is described in the tboot project. The tboot project also contains code for tools to create and provision the policy. @@ -121,30 +133,34 @@ o Tboot then applies an (optional) user-defined launch policy to then any kernel will be launched. - Policy action is flexible and can include halting on failures or simply logging them and continuing. -o Tboot adjusts the e820 table provided by the bootloader to reserve + +- Tboot adjusts the e820 table provided by the bootloader to reserve its own location in memory as well as to reserve certain other TXT-related regions. -o As part of its launch, tboot DMA protects all of RAM (using the +- As part of its launch, tboot DMA protects all of RAM (using the VT-d PMRs). Thus, the kernel must be booted with 'intel_iommu=on' in order to remove this blanket protection and use VT-d's page-level protection. -o Tboot will populate a shared page with some data about itself and +- Tboot will populate a shared page with some data about itself and pass this to the Linux kernel as it transfers control. + - The location of the shared page is passed via the boot_params struct as a physical address. -o The kernel will look for the tboot shared page address and, if it + +- The kernel will look for the tboot shared page address and, if it exists, map it. -o As one of the checks/protections provided by TXT, it makes a copy +- As one of the checks/protections provided by TXT, it makes a copy of the VT-d DMARs in a DMA-protected region of memory and verifies them for correctness. The VT-d code will detect if the kernel was launched with tboot and use this copy instead of the one in the ACPI table. -o At this point, tboot and TXT are out of the picture until a +- At this point, tboot and TXT are out of the picture until a shutdown (S<n>) -o In order to put a system into any of the sleep states after a TXT +- In order to put a system into any of the sleep states after a TXT launch, TXT must first be exited. This is to prevent attacks that attempt to crash the system to gain control on reboot and steal data left in memory. + - The kernel will perform all of its sleep preparation and populate the shared page with the ACPI data needed to put the platform in the desired sleep state. @@ -172,7 +188,7 @@ o In order to put a system into any of the sleep states after a TXT That's pretty much it for TXT support. -Configuring the System: +Configuring the System ====================== This code works with 32bit, 32bit PAE, and 64bit (x86_64) kernels. @@ -181,7 +197,8 @@ In BIOS, the user must enable: TPM, TXT, VT-x, VT-d. Not all BIOSes allow these to be individually enabled/disabled and the screens in which to find them are BIOS-specific. -grub.conf needs to be modified as follows: +grub.conf needs to be modified as follows:: + title Linux 2.6.29-tip w/ tboot root (hd0,0) kernel /tboot.gz logging=serial,vga,memory diff --git a/Documentation/io-mapping.txt b/Documentation/io-mapping.txt index 5ca78426f54c..a966239f04e4 100644 --- a/Documentation/io-mapping.txt +++ b/Documentation/io-mapping.txt @@ -1,66 +1,81 @@ +======================== +The io_mapping functions +======================== + +API +=== + The io_mapping functions in linux/io-mapping.h provide an abstraction for efficiently mapping small regions of an I/O device to the CPU. The initial usage is to support the large graphics aperture on 32-bit processors where ioremap_wc cannot be used to statically map the entire aperture to the CPU as it would consume too much of the kernel address space. -A mapping object is created during driver initialization using +A mapping object is created during driver initialization using:: struct io_mapping *io_mapping_create_wc(unsigned long base, unsigned long size) - 'base' is the bus address of the region to be made - mappable, while 'size' indicates how large a mapping region to - enable. Both are in bytes. +'base' is the bus address of the region to be made +mappable, while 'size' indicates how large a mapping region to +enable. Both are in bytes. - This _wc variant provides a mapping which may only be used - with the io_mapping_map_atomic_wc or io_mapping_map_wc. +This _wc variant provides a mapping which may only be used +with the io_mapping_map_atomic_wc or io_mapping_map_wc. With this mapping object, individual pages can be mapped either atomically or not, depending on the necessary scheduling environment. Of course, atomic -maps are more efficient: +maps are more efficient:: void *io_mapping_map_atomic_wc(struct io_mapping *mapping, unsigned long offset) - 'offset' is the offset within the defined mapping region. - Accessing addresses beyond the region specified in the - creation function yields undefined results. Using an offset - which is not page aligned yields an undefined result. The - return value points to a single page in CPU address space. +'offset' is the offset within the defined mapping region. +Accessing addresses beyond the region specified in the +creation function yields undefined results. Using an offset +which is not page aligned yields an undefined result. The +return value points to a single page in CPU address space. + +This _wc variant returns a write-combining map to the +page and may only be used with mappings created by +io_mapping_create_wc - This _wc variant returns a write-combining map to the - page and may only be used with mappings created by - io_mapping_create_wc +Note that the task may not sleep while holding this page +mapped. - Note that the task may not sleep while holding this page - mapped. +:: void io_mapping_unmap_atomic(void *vaddr) - 'vaddr' must be the value returned by the last - io_mapping_map_atomic_wc call. This unmaps the specified - page and allows the task to sleep once again. +'vaddr' must be the value returned by the last +io_mapping_map_atomic_wc call. This unmaps the specified +page and allows the task to sleep once again. If you need to sleep while holding the lock, you can use the non-atomic variant, although they may be significantly slower. +:: + void *io_mapping_map_wc(struct io_mapping *mapping, unsigned long offset) - This works like io_mapping_map_atomic_wc except it allows - the task to sleep while holding the page mapped. +This works like io_mapping_map_atomic_wc except it allows +the task to sleep while holding the page mapped. + + +:: void io_mapping_unmap(void *vaddr) - This works like io_mapping_unmap_atomic, except it is used - for pages mapped with io_mapping_map_wc. +This works like io_mapping_unmap_atomic, except it is used +for pages mapped with io_mapping_map_wc. -At driver close time, the io_mapping object must be freed: +At driver close time, the io_mapping object must be freed:: void io_mapping_free(struct io_mapping *mapping) -Current Implementation: +Current Implementation +====================== The initial implementation of these functions uses existing mapping mechanisms and so provides only an abstraction layer and no new diff --git a/Documentation/io_ordering.txt b/Documentation/io_ordering.txt index 9faae6f26d32..2ab303ce9a0d 100644 --- a/Documentation/io_ordering.txt +++ b/Documentation/io_ordering.txt @@ -1,3 +1,7 @@ +============================================== +Ordering I/O writes to memory-mapped addresses +============================================== + On some platforms, so-called memory-mapped I/O is weakly ordered. On such platforms, driver writers are responsible for ensuring that I/O writes to memory-mapped addresses on their device arrive in the order intended. This is @@ -8,39 +12,39 @@ critical section of code protected by spinlocks. This would ensure that subsequent writes to I/O space arrived only after all prior writes (much like a memory barrier op, mb(), only with respect to I/O). -A more concrete example from a hypothetical device driver: +A more concrete example from a hypothetical device driver:: - ... -CPU A: spin_lock_irqsave(&dev_lock, flags) -CPU A: val = readl(my_status); -CPU A: ... -CPU A: writel(newval, ring_ptr); -CPU A: spin_unlock_irqrestore(&dev_lock, flags) - ... -CPU B: spin_lock_irqsave(&dev_lock, flags) -CPU B: val = readl(my_status); -CPU B: ... -CPU B: writel(newval2, ring_ptr); -CPU B: spin_unlock_irqrestore(&dev_lock, flags) - ... + ... + CPU A: spin_lock_irqsave(&dev_lock, flags) + CPU A: val = readl(my_status); + CPU A: ... + CPU A: writel(newval, ring_ptr); + CPU A: spin_unlock_irqrestore(&dev_lock, flags) + ... + CPU B: spin_lock_irqsave(&dev_lock, flags) + CPU B: val = readl(my_status); + CPU B: ... + CPU B: writel(newval2, ring_ptr); + CPU B: spin_unlock_irqrestore(&dev_lock, flags) + ... In the case above, the device may receive newval2 before it receives newval, -which could cause problems. Fixing it is easy enough though: +which could cause problems. Fixing it is easy enough though:: - ... -CPU A: spin_lock_irqsave(&dev_lock, flags) -CPU A: val = readl(my_status); -CPU A: ... -CPU A: writel(newval, ring_ptr); -CPU A: (void)readl(safe_register); /* maybe a config register? */ -CPU A: spin_unlock_irqrestore(&dev_lock, flags) - ... -CPU B: spin_lock_irqsave(&dev_lock, flags) -CPU B: val = readl(my_status); -CPU B: ... -CPU B: writel(newval2, ring_ptr); -CPU B: (void)readl(safe_register); /* maybe a config register? */ -CPU B: spin_unlock_irqrestore(&dev_lock, flags) + ... + CPU A: spin_lock_irqsave(&dev_lock, flags) + CPU A: val = readl(my_status); + CPU A: ... + CPU A: writel(newval, ring_ptr); + CPU A: (void)readl(safe_register); /* maybe a config register? */ + CPU A: spin_unlock_irqrestore(&dev_lock, flags) + ... + CPU B: spin_lock_irqsave(&dev_lock, flags) + CPU B: val = readl(my_status); + CPU B: ... + CPU B: writel(newval2, ring_ptr); + CPU B: (void)readl(safe_register); /* maybe a config register? */ + CPU B: spin_unlock_irqrestore(&dev_lock, flags) Here, the reads from safe_register will cause the I/O chipset to flush any pending writes before actually posting the read to the chipset, preventing diff --git a/Documentation/iostats.txt b/Documentation/iostats.txt index 65f694f2d1c9..04d394a2e06c 100644 --- a/Documentation/iostats.txt +++ b/Documentation/iostats.txt @@ -1,49 +1,50 @@ +===================== I/O statistics fields ---------------- +===================== Since 2.4.20 (and some versions before, with patches), and 2.5.45, more extensive disk statistics have been introduced to help measure disk -activity. Tools such as sar and iostat typically interpret these and do +activity. Tools such as ``sar`` and ``iostat`` typically interpret these and do the work for you, but in case you are interested in creating your own tools, the fields are explained here. In 2.4 now, the information is found as additional fields in -/proc/partitions. In 2.6, the same information is found in two -places: one is in the file /proc/diskstats, and the other is within +``/proc/partitions``. In 2.6 and upper, the same information is found in two +places: one is in the file ``/proc/diskstats``, and the other is within the sysfs file system, which must be mounted in order to obtain the information. Throughout this document we'll assume that sysfs -is mounted on /sys, although of course it may be mounted anywhere. -Both /proc/diskstats and sysfs use the same source for the information +is mounted on ``/sys``, although of course it may be mounted anywhere. +Both ``/proc/diskstats`` and sysfs use the same source for the information and so should not differ. -Here are examples of these different formats: +Here are examples of these different formats:: -2.4: - 3 0 39082680 hda 446216 784926 9550688 4382310 424847 312726 5922052 19310380 0 3376340 23705160 - 3 1 9221278 hda1 35486 0 35496 38030 0 0 0 0 0 38030 38030 + 2.4: + 3 0 39082680 hda 446216 784926 9550688 4382310 424847 312726 5922052 19310380 0 3376340 23705160 + 3 1 9221278 hda1 35486 0 35496 38030 0 0 0 0 0 38030 38030 + 2.6+ sysfs: + 446216 784926 9550688 4382310 424847 312726 5922052 19310380 0 3376340 23705160 + 35486 38030 38030 38030 -2.6 sysfs: - 446216 784926 9550688 4382310 424847 312726 5922052 19310380 0 3376340 23705160 - 35486 38030 38030 38030 + 2.6+ diskstats: + 3 0 hda 446216 784926 9550688 4382310 424847 312726 5922052 19310380 0 3376340 23705160 + 3 1 hda1 35486 38030 38030 38030 -2.6 diskstats: - 3 0 hda 446216 784926 9550688 4382310 424847 312726 5922052 19310380 0 3376340 23705160 - 3 1 hda1 35486 38030 38030 38030 +On 2.4 you might execute ``grep 'hda ' /proc/partitions``. On 2.6+, you have +a choice of ``cat /sys/block/hda/stat`` or ``grep 'hda ' /proc/diskstats``. -On 2.4 you might execute "grep 'hda ' /proc/partitions". On 2.6, you have -a choice of "cat /sys/block/hda/stat" or "grep 'hda ' /proc/diskstats". The advantage of one over the other is that the sysfs choice works well -if you are watching a known, small set of disks. /proc/diskstats may +if you are watching a known, small set of disks. ``/proc/diskstats`` may be a better choice if you are watching a large number of disks because you'll avoid the overhead of 50, 100, or 500 or more opens/closes with each snapshot of your disk statistics. In 2.4, the statistics fields are those after the device name. In the above example, the first field of statistics would be 446216. -By contrast, in 2.6 if you look at /sys/block/hda/stat, you'll +By contrast, in 2.6+ if you look at ``/sys/block/hda/stat``, you'll find just the eleven fields, beginning with 446216. If you look at -/proc/diskstats, the eleven fields will be preceded by the major and +``/proc/diskstats``, the eleven fields will be preceded by the major and minor device numbers, and device name. Each of these formats provides eleven fields of statistics, each meaning exactly the same things. All fields except field 9 are cumulative since boot. Field 9 should @@ -59,30 +60,40 @@ system-wide stats you'll have to find all the devices and sum them all up. Field 1 -- # of reads completed This is the total number of reads completed successfully. + Field 2 -- # of reads merged, field 6 -- # of writes merged Reads and writes which are adjacent to each other may be merged for efficiency. Thus two 4K reads may become one 8K read before it is ultimately handed to the disk, and so it will be counted (and queued) as only one I/O. This field lets you know how often this was done. + Field 3 -- # of sectors read This is the total number of sectors read successfully. + Field 4 -- # of milliseconds spent reading This is the total number of milliseconds spent by all reads (as measured from __make_request() to end_that_request_last()). + Field 5 -- # of writes completed This is the total number of writes completed successfully. + Field 6 -- # of writes merged See the description of field 2. + Field 7 -- # of sectors written This is the total number of sectors written successfully. + Field 8 -- # of milliseconds spent writing This is the total number of milliseconds spent by all writes (as measured from __make_request() to end_that_request_last()). + Field 9 -- # of I/Os currently in progress The only field that should go to zero. Incremented as requests are given to appropriate struct request_queue and decremented as they finish. + Field 10 -- # of milliseconds spent doing I/Os This field increases so long as field 9 is nonzero. + Field 11 -- weighted # of milliseconds spent doing I/Os This field is incremented at each I/O start, I/O completion, I/O merge, or read of these stats by the number of I/Os in progress @@ -97,7 +108,7 @@ introduced when changes collide, so (for instance) adding up all the read I/Os issued per partition should equal those made to the disks ... but due to the lack of locking it may only be very close. -In 2.6, there are counters for each CPU, which make the lack of locking +In 2.6+, there are counters for each CPU, which make the lack of locking almost a non-issue. When the statistics are read, the per-CPU counters are summed (possibly overflowing the unsigned long variable they are summed to) and the result given to the user. There is no convenient @@ -106,22 +117,25 @@ user interface for accessing the per-CPU counters themselves. Disks vs Partitions ------------------- -There were significant changes between 2.4 and 2.6 in the I/O subsystem. +There were significant changes between 2.4 and 2.6+ in the I/O subsystem. As a result, some statistic information disappeared. The translation from a disk address relative to a partition to the disk address relative to the host disk happens much earlier. All merges and timings now happen at the disk level rather than at both the disk and partition level as -in 2.4. Consequently, you'll see a different statistics output on 2.6 for +in 2.4. Consequently, you'll see a different statistics output on 2.6+ for partitions from that for disks. There are only *four* fields available -for partitions on 2.6 machines. This is reflected in the examples above. +for partitions on 2.6+ machines. This is reflected in the examples above. Field 1 -- # of reads issued This is the total number of reads issued to this partition. + Field 2 -- # of sectors read This is the total number of sectors requested to be read from this partition. + Field 3 -- # of writes issued This is the total number of writes issued to this partition. + Field 4 -- # of sectors written This is the total number of sectors requested to be written to this partition. @@ -149,16 +163,16 @@ to some (probably insignificant) inaccuracy. Additional notes ---------------- -In 2.6, sysfs is not mounted by default. If your distribution of +In 2.6+, sysfs is not mounted by default. If your distribution of Linux hasn't added it already, here's the line you'll want to add to -your /etc/fstab: +your ``/etc/fstab``:: -none /sys sysfs defaults 0 0 + none /sys sysfs defaults 0 0 -In 2.6, all disk statistics were removed from /proc/stat. In 2.4, they -appear in both /proc/partitions and /proc/stat, although the ones in -/proc/stat take a very different format from those in /proc/partitions +In 2.6+, all disk statistics were removed from ``/proc/stat``. In 2.4, they +appear in both ``/proc/partitions`` and ``/proc/stat``, although the ones in +``/proc/stat`` take a very different format from those in ``/proc/partitions`` (see proc(5), if your system has it.) -- ricklind@us.ibm.com diff --git a/Documentation/irqflags-tracing.txt b/Documentation/irqflags-tracing.txt index f6da05670e16..bdd208259fb3 100644 --- a/Documentation/irqflags-tracing.txt +++ b/Documentation/irqflags-tracing.txt @@ -1,8 +1,10 @@ +======================= IRQ-flags state tracing +======================= -started by Ingo Molnar <mingo@redhat.com> +:Author: started by Ingo Molnar <mingo@redhat.com> -the "irq-flags tracing" feature "traces" hardirq and softirq state, in +The "irq-flags tracing" feature "traces" hardirq and softirq state, in that it gives interested subsystems an opportunity to be notified of every hardirqs-off/hardirqs-on, softirqs-off/softirqs-on event that happens in the kernel. @@ -14,7 +16,7 @@ CONFIG_PROVE_RWSEM_LOCKING will be offered on an architecture - these are locking APIs that are not used in IRQ context. (the one exception for rwsems is worked around) -architecture support for this is certainly not in the "trivial" +Architecture support for this is certainly not in the "trivial" category, because lots of lowlevel assembly code deal with irq-flags state changes. But an architecture can be irq-flags-tracing enabled in a rather straightforward and risk-free manner. @@ -41,7 +43,7 @@ irq-flags-tracing support: excluded from the irq-tracing [and lock validation] mechanism via lockdep_off()/lockdep_on(). -in general there is no risk from having an incomplete irq-flags-tracing +In general there is no risk from having an incomplete irq-flags-tracing implementation in an architecture: lockdep will detect that and will turn itself off. I.e. the lock validator will still be reliable. There should be no crashes due to irq-tracing bugs. (except if the assembly diff --git a/Documentation/isa.txt b/Documentation/isa.txt index f232c26a40be..def4a7b690b5 100644 --- a/Documentation/isa.txt +++ b/Documentation/isa.txt @@ -1,5 +1,6 @@ +=========== ISA Drivers ------------ +=========== The following text is adapted from the commit message of the initial commit of the ISA bus driver authored by Rene Herman. @@ -23,17 +24,17 @@ that all device creation has been made internal as well. The usage model this provides is nice, and has been acked from the ALSA side by Takashi Iwai and Jaroslav Kysela. The ALSA driver module_init's -now (for oldisa-only drivers) become: +now (for oldisa-only drivers) become:: -static int __init alsa_card_foo_init(void) -{ - return isa_register_driver(&snd_foo_isa_driver, SNDRV_CARDS); -} + static int __init alsa_card_foo_init(void) + { + return isa_register_driver(&snd_foo_isa_driver, SNDRV_CARDS); + } -static void __exit alsa_card_foo_exit(void) -{ - isa_unregister_driver(&snd_foo_isa_driver); -} + static void __exit alsa_card_foo_exit(void) + { + isa_unregister_driver(&snd_foo_isa_driver); + } Quite like the other bus models therefore. This removes a lot of duplicated init code from the ALSA ISA drivers. @@ -47,11 +48,11 @@ parameter, indicating how many devices to create and call our methods with. The platform_driver callbacks are called with a platform_device param; -the isa_driver callbacks are being called with a "struct device *dev, -unsigned int id" pair directly -- with the device creation completely +the isa_driver callbacks are being called with a ``struct device *dev, +unsigned int id`` pair directly -- with the device creation completely internal to the bus it's much cleaner to not leak isa_dev's by passing them in at all. The id is the only thing we ever want other then the -struct device * anyways, and it makes for nicer code in the callbacks as +struct device anyways, and it makes for nicer code in the callbacks as well. With this additional .match() callback ISA drivers have all options. If @@ -75,20 +76,20 @@ This exports only two functions; isa_{,un}register_driver(). isa_register_driver() register's the struct device_driver, and then loops over the passed in ndev creating devices and registering them. -This causes the bus match method to be called for them, which is: +This causes the bus match method to be called for them, which is:: -int isa_bus_match(struct device *dev, struct device_driver *driver) -{ - struct isa_driver *isa_driver = to_isa_driver(driver); + int isa_bus_match(struct device *dev, struct device_driver *driver) + { + struct isa_driver *isa_driver = to_isa_driver(driver); - if (dev->platform_data == isa_driver) { - if (!isa_driver->match || - isa_driver->match(dev, to_isa_dev(dev)->id)) - return 1; - dev->platform_data = NULL; - } - return 0; -} + if (dev->platform_data == isa_driver) { + if (!isa_driver->match || + isa_driver->match(dev, to_isa_dev(dev)->id)) + return 1; + dev->platform_data = NULL; + } + return 0; + } The first thing this does is check if this device is in fact one of this driver's devices by seeing if the device's platform_data pointer is set @@ -102,7 +103,7 @@ well. Then, if the the driver did not provide a .match, it matches. If it did, the driver match() method is called to determine a match. -If it did _not_ match, dev->platform_data is reset to indicate this to +If it did **not** match, dev->platform_data is reset to indicate this to isa_register_driver which can then unregister the device again. If during all this, there's any error, or no devices matched at all diff --git a/Documentation/isapnp.txt b/Documentation/isapnp.txt index 400d1b5b523d..8d0840ac847b 100644 --- a/Documentation/isapnp.txt +++ b/Documentation/isapnp.txt @@ -1,3 +1,4 @@ +========================================================== ISA Plug & Play support by Jaroslav Kysela <perex@suse.cz> ========================================================== diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt index 615434d81108..51814450a7f8 100644 --- a/Documentation/kdump/kdump.txt +++ b/Documentation/kdump/kdump.txt @@ -112,8 +112,8 @@ There are two possible methods of using Kdump. 2) Or use the system kernel binary itself as dump-capture kernel and there is no need to build a separate dump-capture kernel. This is possible only with the architectures which support a relocatable kernel. As - of today, i386, x86_64, ppc64, ia64 and arm architectures support relocatable - kernel. + of today, i386, x86_64, ppc64, ia64, arm and arm64 architectures support + relocatable kernel. Building a relocatable kernel is advantageous from the point of view that one does not have to build a second kernel for capturing the dump. But @@ -339,7 +339,7 @@ For arm: For arm64: - Use vmlinux or Image -If you are using a uncompressed vmlinux image then use following command +If you are using an uncompressed vmlinux image then use following command to load dump-capture kernel. kexec -p <dump-capture-kernel-vmlinux-image> \ @@ -361,6 +361,12 @@ to load dump-capture kernel. --dtb=<dtb-for-dump-capture-kernel> \ --append="root=<root-dev> <arch-specific-options>" +If you are using an uncompressed Image, then use following command +to load dump-capture kernel. + + kexec -p <dump-capture-kernel-Image> \ + --initrd=<initrd-for-dump-capture-kernel> \ + --append="root=<root-dev> <arch-specific-options>" Please note, that --args-linux does not need to be specified for ia64. It is planned to make this a no-op on that architecture, but for now diff --git a/Documentation/kernel-per-CPU-kthreads.txt b/Documentation/kernel-per-CPU-kthreads.txt index 2cb7dc5c0e0d..0f00f9c164ac 100644 --- a/Documentation/kernel-per-CPU-kthreads.txt +++ b/Documentation/kernel-per-CPU-kthreads.txt @@ -1,27 +1,29 @@ -REDUCING OS JITTER DUE TO PER-CPU KTHREADS +========================================== +Reducing OS jitter due to per-cpu kthreads +========================================== This document lists per-CPU kthreads in the Linux kernel and presents options to control their OS jitter. Note that non-per-CPU kthreads are not listed here. To reduce OS jitter from non-per-CPU kthreads, bind them to a "housekeeping" CPU dedicated to such work. +References +========== -REFERENCES +- Documentation/IRQ-affinity.txt: Binding interrupts to sets of CPUs. -o Documentation/IRQ-affinity.txt: Binding interrupts to sets of CPUs. +- Documentation/cgroup-v1: Using cgroups to bind tasks to sets of CPUs. -o Documentation/cgroup-v1: Using cgroups to bind tasks to sets of CPUs. - -o man taskset: Using the taskset command to bind tasks to sets +- man taskset: Using the taskset command to bind tasks to sets of CPUs. -o man sched_setaffinity: Using the sched_setaffinity() system +- man sched_setaffinity: Using the sched_setaffinity() system call to bind tasks to sets of CPUs. -o /sys/devices/system/cpu/cpuN/online: Control CPU N's hotplug state, +- /sys/devices/system/cpu/cpuN/online: Control CPU N's hotplug state, writing "0" to offline and "1" to online. -o In order to locate kernel-generated OS jitter on CPU N: +- In order to locate kernel-generated OS jitter on CPU N: cd /sys/kernel/debug/tracing echo 1 > max_graph_depth # Increase the "1" for more detail @@ -29,12 +31,17 @@ o In order to locate kernel-generated OS jitter on CPU N: # run workload cat per_cpu/cpuN/trace +kthreads +======== + +Name: + ehca_comp/%u -KTHREADS +Purpose: + Periodically process Infiniband-related work. -Name: ehca_comp/%u -Purpose: Periodically process Infiniband-related work. To reduce its OS jitter, do any of the following: + 1. Don't use eHCA Infiniband hardware, instead choosing hardware that does not require per-CPU kthreads. This will prevent these kthreads from being created in the first place. (This will @@ -46,26 +53,45 @@ To reduce its OS jitter, do any of the following: provisioned only on selected CPUs. -Name: irq/%d-%s -Purpose: Handle threaded interrupts. +Name: + irq/%d-%s + +Purpose: + Handle threaded interrupts. + To reduce its OS jitter, do the following: + 1. Use irq affinity to force the irq threads to execute on some other CPU. -Name: kcmtpd_ctr_%d -Purpose: Handle Bluetooth work. +Name: + kcmtpd_ctr_%d + +Purpose: + Handle Bluetooth work. + To reduce its OS jitter, do one of the following: + 1. Don't use Bluetooth, in which case these kthreads won't be created in the first place. 2. Use irq affinity to force Bluetooth-related interrupts to occur on some other CPU and furthermore initiate all Bluetooth activity on some other CPU. -Name: ksoftirqd/%u -Purpose: Execute softirq handlers when threaded or when under heavy load. +Name: + ksoftirqd/%u + +Purpose: + Execute softirq handlers when threaded or when under heavy load. + To reduce its OS jitter, each softirq vector must be handled separately as follows: -TIMER_SOFTIRQ: Do all of the following: + +TIMER_SOFTIRQ +------------- + +Do all of the following: + 1. To the extent possible, keep the CPU out of the kernel when it is non-idle, for example, by avoiding system calls and by forcing both kernel threads and interrupts to execute elsewhere. @@ -76,34 +102,59 @@ TIMER_SOFTIRQ: Do all of the following: first one back online. Once you have onlined the CPUs in question, do not offline any other CPUs, because doing so could force the timer back onto one of the CPUs in question. -NET_TX_SOFTIRQ and NET_RX_SOFTIRQ: Do all of the following: + +NET_TX_SOFTIRQ and NET_RX_SOFTIRQ +--------------------------------- + +Do all of the following: + 1. Force networking interrupts onto other CPUs. 2. Initiate any network I/O on other CPUs. 3. Once your application has started, prevent CPU-hotplug operations from being initiated from tasks that might run on the CPU to be de-jittered. (It is OK to force this CPU offline and then bring it back online before you start your application.) -BLOCK_SOFTIRQ: Do all of the following: + +BLOCK_SOFTIRQ +------------- + +Do all of the following: + 1. Force block-device interrupts onto some other CPU. 2. Initiate any block I/O on other CPUs. 3. Once your application has started, prevent CPU-hotplug operations from being initiated from tasks that might run on the CPU to be de-jittered. (It is OK to force this CPU offline and then bring it back online before you start your application.) -IRQ_POLL_SOFTIRQ: Do all of the following: + +IRQ_POLL_SOFTIRQ +---------------- + +Do all of the following: + 1. Force block-device interrupts onto some other CPU. 2. Initiate any block I/O and block-I/O polling on other CPUs. 3. Once your application has started, prevent CPU-hotplug operations from being initiated from tasks that might run on the CPU to be de-jittered. (It is OK to force this CPU offline and then bring it back online before you start your application.) -TASKLET_SOFTIRQ: Do one or more of the following: + +TASKLET_SOFTIRQ +--------------- + +Do one or more of the following: + 1. Avoid use of drivers that use tasklets. (Such drivers will contain calls to things like tasklet_schedule().) 2. Convert all drivers that you must use from tasklets to workqueues. 3. Force interrupts for drivers using tasklets onto other CPUs, and also do I/O involving these drivers on other CPUs. -SCHED_SOFTIRQ: Do all of the following: + +SCHED_SOFTIRQ +------------- + +Do all of the following: + 1. Avoid sending scheduler IPIs to the CPU to be de-jittered, for example, ensure that at most one runnable kthread is present on that CPU. If a thread that expects to run on the de-jittered @@ -120,7 +171,12 @@ SCHED_SOFTIRQ: Do all of the following: forcing both kernel threads and interrupts to execute elsewhere. This further reduces the number of scheduler-clock interrupts received by the de-jittered CPU. -HRTIMER_SOFTIRQ: Do all of the following: + +HRTIMER_SOFTIRQ +--------------- + +Do all of the following: + 1. To the extent possible, keep the CPU out of the kernel when it is non-idle. For example, avoid system calls and force both kernel threads and interrupts to execute elsewhere. @@ -131,9 +187,15 @@ HRTIMER_SOFTIRQ: Do all of the following: back online. Once you have onlined the CPUs in question, do not offline any other CPUs, because doing so could force the timer back onto one of the CPUs in question. -RCU_SOFTIRQ: Do at least one of the following: + +RCU_SOFTIRQ +----------- + +Do at least one of the following: + 1. Offload callbacks and keep the CPU in either dyntick-idle or adaptive-ticks state by doing all of the following: + a. CONFIG_NO_HZ_FULL=y and ensure that the CPU to be de-jittered is marked as an adaptive-ticks CPU using the "nohz_full=" boot parameter. Bind the rcuo kthreads to @@ -142,8 +204,10 @@ RCU_SOFTIRQ: Do at least one of the following: when it is non-idle, for example, by avoiding system calls and by forcing both kernel threads and interrupts to execute elsewhere. + 2. Enable RCU to do its processing remotely via dyntick-idle by doing all of the following: + a. Build with CONFIG_NO_HZ=y and CONFIG_RCU_FAST_NO_HZ=y. b. Ensure that the CPU goes idle frequently, allowing other CPUs to detect that it has passed through an RCU quiescent @@ -155,15 +219,20 @@ RCU_SOFTIRQ: Do at least one of the following: calls and by forcing both kernel threads and interrupts to execute elsewhere. -Name: kworker/%u:%d%s (cpu, id, priority) -Purpose: Execute workqueue requests +Name: + kworker/%u:%d%s (cpu, id, priority) + +Purpose: + Execute workqueue requests + To reduce its OS jitter, do any of the following: + 1. Run your workload at a real-time priority, which will allow preempting the kworker daemons. 2. A given workqueue can be made visible in the sysfs filesystem by passing the WQ_SYSFS to that workqueue's alloc_workqueue(). Such a workqueue can be confined to a given subset of the - CPUs using the /sys/devices/virtual/workqueue/*/cpumask sysfs + CPUs using the ``/sys/devices/virtual/workqueue/*/cpumask`` sysfs files. The set of WQ_SYSFS workqueues can be displayed using "ls sys/devices/virtual/workqueue". That said, the workqueues maintainer would like to caution people against indiscriminately @@ -173,6 +242,7 @@ To reduce its OS jitter, do any of the following: to remove it, even if its addition was a mistake. 3. Do any of the following needed to avoid jitter that your application cannot tolerate: + a. Build your kernel with CONFIG_SLUB=y rather than CONFIG_SLAB=y, thus avoiding the slab allocator's periodic use of each CPU's workqueues to run its cache_reap() @@ -186,6 +256,7 @@ To reduce its OS jitter, do any of the following: be able to build your kernel with CONFIG_CPU_FREQ=n to avoid the CPU-frequency governor periodically running on each CPU, including cs_dbs_timer() and od_dbs_timer(). + WARNING: Please check your CPU specifications to make sure that this is safe on your particular system. d. As of v3.18, Christoph Lameter's on-demand vmstat workers @@ -222,9 +293,14 @@ To reduce its OS jitter, do any of the following: CONFIG_PMAC_RACKMETER=n to disable the CPU-meter, avoiding OS jitter from rackmeter_do_timer(). -Name: rcuc/%u -Purpose: Execute RCU callbacks in CONFIG_RCU_BOOST=y kernels. +Name: + rcuc/%u + +Purpose: + Execute RCU callbacks in CONFIG_RCU_BOOST=y kernels. + To reduce its OS jitter, do at least one of the following: + 1. Build the kernel with CONFIG_PREEMPT=n. This prevents these kthreads from being created in the first place, and also obviates the need for RCU priority boosting. This approach is feasible @@ -244,9 +320,14 @@ To reduce its OS jitter, do at least one of the following: CPU, again preventing the rcuc/%u kthreads from having any work to do. -Name: rcuob/%d, rcuop/%d, and rcuos/%d -Purpose: Offload RCU callbacks from the corresponding CPU. +Name: + rcuob/%d, rcuop/%d, and rcuos/%d + +Purpose: + Offload RCU callbacks from the corresponding CPU. + To reduce its OS jitter, do at least one of the following: + 1. Use affinity, cgroups, or other mechanism to force these kthreads to execute on some other CPU. 2. Build with CONFIG_RCU_NOCB_CPU=n, which will prevent these @@ -254,9 +335,14 @@ To reduce its OS jitter, do at least one of the following: note that this will not eliminate OS jitter, but will instead shift it to RCU_SOFTIRQ. -Name: watchdog/%u -Purpose: Detect software lockups on each CPU. +Name: + watchdog/%u + +Purpose: + Detect software lockups on each CPU. + To reduce its OS jitter, do at least one of the following: + 1. Build with CONFIG_LOCKUP_DETECTOR=n, which will prevent these kthreads from being created in the first place. 2. Boot with "nosoftlockup=0", which will also prevent these kthreads diff --git a/Documentation/kobject.txt b/Documentation/kobject.txt index 1be59a3a521c..fc9485d79061 100644 --- a/Documentation/kobject.txt +++ b/Documentation/kobject.txt @@ -1,13 +1,13 @@ +===================================================================== Everything you never wanted to know about kobjects, ksets, and ktypes +===================================================================== -Greg Kroah-Hartman <gregkh@linuxfoundation.org> +:Author: Greg Kroah-Hartman <gregkh@linuxfoundation.org> +:Last updated: December 19, 2007 Based on an original article by Jon Corbet for lwn.net written October 1, 2003 and located at http://lwn.net/Articles/51437/ -Last updated December 19, 2007 - - Part of the difficulty in understanding the driver model - and the kobject abstraction upon which it is built - is that there is no obvious starting place. Dealing with kobjects requires understanding a few different types, @@ -47,6 +47,7 @@ approach will be taken, so we'll go back to kobjects. Embedding kobjects +================== It is rare for kernel code to create a standalone kobject, with one major exception explained below. Instead, kobjects are used to control access to @@ -65,7 +66,7 @@ their own, but are invariably found embedded in the larger objects of interest.) So, for example, the UIO code in drivers/uio/uio.c has a structure that -defines the memory region associated with a uio device: +defines the memory region associated with a uio device:: struct uio_map { struct kobject kobj; @@ -77,7 +78,7 @@ just a matter of using the kobj member. Code that works with kobjects will often have the opposite problem, however: given a struct kobject pointer, what is the pointer to the containing structure? You must avoid tricks (such as assuming that the kobject is at the beginning of the structure) -and, instead, use the container_of() macro, found in <linux/kernel.h>: +and, instead, use the container_of() macro, found in <linux/kernel.h>:: container_of(pointer, type, member) @@ -90,13 +91,13 @@ where: The return value from container_of() is a pointer to the corresponding container type. So, for example, a pointer "kp" to a struct kobject embedded *within* a struct uio_map could be converted to a pointer to the -*containing* uio_map structure with: +*containing* uio_map structure with:: struct uio_map *u_map = container_of(kp, struct uio_map, kobj); For convenience, programmers often define a simple macro for "back-casting" kobject pointers to the containing type. Exactly this happens in the -earlier drivers/uio/uio.c, as you can see here: +earlier drivers/uio/uio.c, as you can see here:: struct uio_map { struct kobject kobj; @@ -106,23 +107,25 @@ earlier drivers/uio/uio.c, as you can see here: #define to_map(map) container_of(map, struct uio_map, kobj) where the macro argument "map" is a pointer to the struct kobject in -question. That macro is subsequently invoked with: +question. That macro is subsequently invoked with:: struct uio_map *map = to_map(kobj); Initialization of kobjects +========================== Code which creates a kobject must, of course, initialize that object. Some -of the internal fields are setup with a (mandatory) call to kobject_init(): +of the internal fields are setup with a (mandatory) call to kobject_init():: void kobject_init(struct kobject *kobj, struct kobj_type *ktype); The ktype is required for a kobject to be created properly, as every kobject must have an associated kobj_type. After calling kobject_init(), to -register the kobject with sysfs, the function kobject_add() must be called: +register the kobject with sysfs, the function kobject_add() must be called:: - int kobject_add(struct kobject *kobj, struct kobject *parent, const char *fmt, ...); + int kobject_add(struct kobject *kobj, struct kobject *parent, + const char *fmt, ...); This sets up the parent of the kobject and the name for the kobject properly. If the kobject is to be associated with a specific kset, @@ -133,7 +136,7 @@ kset itself. As the name of the kobject is set when it is added to the kernel, the name of the kobject should never be manipulated directly. If you must change -the name of the kobject, call kobject_rename(): +the name of the kobject, call kobject_rename():: int kobject_rename(struct kobject *kobj, const char *new_name); @@ -146,12 +149,12 @@ is being removed. If your code needs to call this function, it is incorrect and needs to be fixed. To properly access the name of the kobject, use the function -kobject_name(): +kobject_name():: const char *kobject_name(const struct kobject * kobj); There is a helper function to both initialize and add the kobject to the -kernel at the same time, called surprisingly enough kobject_init_and_add(): +kernel at the same time, called surprisingly enough kobject_init_and_add():: int kobject_init_and_add(struct kobject *kobj, struct kobj_type *ktype, struct kobject *parent, const char *fmt, ...); @@ -161,10 +164,11 @@ kobject_add() functions described above. Uevents +======= After a kobject has been registered with the kobject core, you need to announce to the world that it has been created. This can be done with a -call to kobject_uevent(): +call to kobject_uevent():: int kobject_uevent(struct kobject *kobj, enum kobject_action action); @@ -180,11 +184,12 @@ hand. Reference counts +================ One of the key functions of a kobject is to serve as a reference counter for the object in which it is embedded. As long as references to the object exist, the object (and the code which supports it) must continue to exist. -The low-level functions for manipulating a kobject's reference counts are: +The low-level functions for manipulating a kobject's reference counts are:: struct kobject *kobject_get(struct kobject *kobj); void kobject_put(struct kobject *kobj); @@ -209,21 +214,24 @@ file Documentation/kref.txt in the Linux kernel source tree. Creating "simple" kobjects +========================== Sometimes all that a developer wants is a way to create a simple directory in the sysfs hierarchy, and not have to mess with the whole complication of ksets, show and store functions, and other details. This is the one exception where a single kobject should be created. To create such an -entry, use the function: +entry, use the function:: struct kobject *kobject_create_and_add(char *name, struct kobject *parent); This function will create a kobject and place it in sysfs in the location underneath the specified parent kobject. To create simple attributes -associated with this kobject, use: +associated with this kobject, use:: int sysfs_create_file(struct kobject *kobj, struct attribute *attr); -or + +or:: + int sysfs_create_group(struct kobject *kobj, struct attribute_group *grp); Both types of attributes used here, with a kobject that has been created @@ -236,6 +244,7 @@ implementation of a simple kobject and attributes. ktypes and release methods +========================== One important thing still missing from the discussion is what happens to a kobject when its reference count reaches zero. The code which created the @@ -257,7 +266,7 @@ is good practice to always use kobject_put() after kobject_init() to avoid errors creeping in. This notification is done through a kobject's release() method. Usually -such a method has a form like: +such a method has a form like:: void my_object_release(struct kobject *kobj) { @@ -281,7 +290,7 @@ leak in the kobject core, which makes people unhappy. Interestingly, the release() method is not stored in the kobject itself; instead, it is associated with the ktype. So let us introduce struct -kobj_type: +kobj_type:: struct kobj_type { void (*release)(struct kobject *kobj); @@ -306,6 +315,7 @@ automatically created for any kobject that is registered with this ktype. ksets +===== A kset is merely a collection of kobjects that want to be associated with each other. There is no restriction that they be of the same ktype, but be @@ -335,13 +345,16 @@ kobject) in their parent. As a kset contains a kobject within it, it should always be dynamically created and never declared statically or on the stack. To create a new -kset use: +kset use:: + struct kset *kset_create_and_add(const char *name, struct kset_uevent_ops *u, struct kobject *parent); -When you are finished with the kset, call: +When you are finished with the kset, call:: + void kset_unregister(struct kset *kset); + to destroy it. This removes the kset from sysfs and decrements its reference count. When the reference count goes to zero, the kset will be released. Because other references to the kset may still exist, the release may happen @@ -351,14 +364,14 @@ An example of using a kset can be seen in the samples/kobject/kset-example.c file in the kernel tree. If a kset wishes to control the uevent operations of the kobjects -associated with it, it can use the struct kset_uevent_ops to handle it: +associated with it, it can use the struct kset_uevent_ops to handle it:: -struct kset_uevent_ops { + struct kset_uevent_ops { int (*filter)(struct kset *kset, struct kobject *kobj); const char *(*name)(struct kset *kset, struct kobject *kobj); int (*uevent)(struct kset *kset, struct kobject *kobj, struct kobj_uevent_env *env); -}; + }; The filter function allows a kset to prevent a uevent from being emitted to @@ -386,6 +399,7 @@ added below the parent kobject. Kobject removal +=============== After a kobject has been registered with the kobject core successfully, it must be cleaned up when the code is finished with it. To do that, call @@ -409,6 +423,7 @@ called, and the objects in the former circle release each other. Example code to copy from +========================= For a more complete example of using ksets and kobjects properly, see the example programs samples/kobject/{kobject-example.c,kset-example.c}, diff --git a/Documentation/kprobes.txt b/Documentation/kprobes.txt index 1f6d45abfe42..2335715bf471 100644 --- a/Documentation/kprobes.txt +++ b/Documentation/kprobes.txt @@ -1,30 +1,36 @@ -Title : Kernel Probes (Kprobes) -Authors : Jim Keniston <jkenisto@us.ibm.com> - : Prasanna S Panchamukhi <prasanna.panchamukhi@gmail.com> - : Masami Hiramatsu <mhiramat@redhat.com> - -CONTENTS - -1. Concepts: Kprobes, Jprobes, Return Probes -2. Architectures Supported -3. Configuring Kprobes -4. API Reference -5. Kprobes Features and Limitations -6. Probe Overhead -7. TODO -8. Kprobes Example -9. Jprobes Example -10. Kretprobes Example -Appendix A: The kprobes debugfs interface -Appendix B: The kprobes sysctl interface - -1. Concepts: Kprobes, Jprobes, Return Probes +======================= +Kernel Probes (Kprobes) +======================= + +:Author: Jim Keniston <jkenisto@us.ibm.com> +:Author: Prasanna S Panchamukhi <prasanna.panchamukhi@gmail.com> +:Author: Masami Hiramatsu <mhiramat@redhat.com> + +.. CONTENTS + + 1. Concepts: Kprobes, Jprobes, Return Probes + 2. Architectures Supported + 3. Configuring Kprobes + 4. API Reference + 5. Kprobes Features and Limitations + 6. Probe Overhead + 7. TODO + 8. Kprobes Example + 9. Jprobes Example + 10. Kretprobes Example + Appendix A: The kprobes debugfs interface + Appendix B: The kprobes sysctl interface + +Concepts: Kprobes, Jprobes, Return Probes +========================================= Kprobes enables you to dynamically break into any kernel routine and collect debugging and performance information non-disruptively. You -can trap at almost any kernel code address(*), specifying a handler +can trap at almost any kernel code address [1]_, specifying a handler routine to be invoked when the breakpoint is hit. -(*: some parts of the kernel code can not be trapped, see 1.5 Blacklist) + +.. [1] some parts of the kernel code can not be trapped, see + :ref:`kprobes_blacklist`) There are currently three types of probes: kprobes, jprobes, and kretprobes (also called return probes). A kprobe can be inserted @@ -40,8 +46,8 @@ registration function such as register_kprobe() specifies where the probe is to be inserted and what handler is to be called when the probe is hit. -There are also register_/unregister_*probes() functions for batch -registration/unregistration of a group of *probes. These functions +There are also ``register_/unregister_*probes()`` functions for batch +registration/unregistration of a group of ``*probes``. These functions can speed up unregistration process when you have to unregister a lot of probes at once. @@ -51,9 +57,10 @@ things that you'll need to know in order to make the best use of Kprobes -- e.g., the difference between a pre_handler and a post_handler, and how to use the maxactive and nmissed fields of a kretprobe. But if you're in a hurry to start using Kprobes, you -can skip ahead to section 2. +can skip ahead to :ref:`kprobes_archs_supported`. -1.1 How Does a Kprobe Work? +How Does a Kprobe Work? +----------------------- When a kprobe is registered, Kprobes makes a copy of the probed instruction and replaces the first byte(s) of the probed instruction @@ -75,7 +82,8 @@ After the instruction is single-stepped, Kprobes executes the "post_handler," if any, that is associated with the kprobe. Execution then continues with the instruction following the probepoint. -1.2 How Does a Jprobe Work? +How Does a Jprobe Work? +----------------------- A jprobe is implemented using a kprobe that is placed on a function's entry point. It employs a simple mirroring principle to allow @@ -113,9 +121,11 @@ more than eight function arguments, an argument of more than sixteen bytes, or more than 64 bytes of argument data, depending on architecture). -1.3 Return Probes +Return Probes +------------- -1.3.1 How Does a Return Probe Work? +How Does a Return Probe Work? +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ When you call register_kretprobe(), Kprobes establishes a kprobe at the entry to the function. When the probed function is called and this @@ -150,7 +160,8 @@ zero when the return probe is registered, and is incremented every time the probed function is entered but there is no kretprobe_instance object available for establishing the return probe. -1.3.2 Kretprobe entry-handler +Kretprobe entry-handler +^^^^^^^^^^^^^^^^^^^^^^^ Kretprobes also provides an optional user-specified handler which runs on function entry. This handler is specified by setting the entry_handler @@ -174,7 +185,10 @@ In case probed function is entered but there is no kretprobe_instance object available, then in addition to incrementing the nmissed count, the user entry_handler invocation is also skipped. -1.4 How Does Jump Optimization Work? +.. _kprobes_jump_optimization: + +How Does Jump Optimization Work? +-------------------------------- If your kernel is built with CONFIG_OPTPROBES=y (currently this flag is automatically set 'y' on x86/x86-64, non-preemptive kernel) and @@ -182,53 +196,60 @@ the "debug.kprobes_optimization" kernel parameter is set to 1 (see sysctl(8)), Kprobes tries to reduce probe-hit overhead by using a jump instruction instead of a breakpoint instruction at each probepoint. -1.4.1 Init a Kprobe +Init a Kprobe +^^^^^^^^^^^^^ When a probe is registered, before attempting this optimization, Kprobes inserts an ordinary, breakpoint-based kprobe at the specified address. So, even if it's not possible to optimize this particular probepoint, there'll be a probe there. -1.4.2 Safety Check +Safety Check +^^^^^^^^^^^^ Before optimizing a probe, Kprobes performs the following safety checks: - Kprobes verifies that the region that will be replaced by the jump -instruction (the "optimized region") lies entirely within one function. -(A jump instruction is multiple bytes, and so may overlay multiple -instructions.) + instruction (the "optimized region") lies entirely within one function. + (A jump instruction is multiple bytes, and so may overlay multiple + instructions.) - Kprobes analyzes the entire function and verifies that there is no -jump into the optimized region. Specifically: + jump into the optimized region. Specifically: + - the function contains no indirect jump; - the function contains no instruction that causes an exception (since - the fixup code triggered by the exception could jump back into the - optimized region -- Kprobes checks the exception tables to verify this); - and + the fixup code triggered by the exception could jump back into the + optimized region -- Kprobes checks the exception tables to verify this); - there is no near jump to the optimized region (other than to the first - byte). + byte). - For each instruction in the optimized region, Kprobes verifies that -the instruction can be executed out of line. + the instruction can be executed out of line. -1.4.3 Preparing Detour Buffer +Preparing Detour Buffer +^^^^^^^^^^^^^^^^^^^^^^^ Next, Kprobes prepares a "detour" buffer, which contains the following instruction sequence: + - code to push the CPU's registers (emulating a breakpoint trap) - a call to the trampoline code which calls user's probe handlers. - code to restore registers - the instructions from the optimized region - a jump back to the original execution path. -1.4.4 Pre-optimization +Pre-optimization +^^^^^^^^^^^^^^^^ After preparing the detour buffer, Kprobes verifies that none of the following situations exist: + - The probe has either a break_handler (i.e., it's a jprobe) or a -post_handler. + post_handler. - Other instructions in the optimized region are probed. - The probe is disabled. + In any of the above cases, Kprobes won't start optimizing the probe. Since these are temporary situations, Kprobes tries to start optimizing it again if the situation is changed. @@ -240,21 +261,23 @@ Kprobes returns control to the original instruction path by setting the CPU's instruction pointer to the copied code in the detour buffer -- thus at least avoiding the single-step. -1.4.5 Optimization +Optimization +^^^^^^^^^^^^ The Kprobe-optimizer doesn't insert the jump instruction immediately; rather, it calls synchronize_sched() for safety first, because it's possible for a CPU to be interrupted in the middle of executing the -optimized region(*). As you know, synchronize_sched() can ensure +optimized region [3]_. As you know, synchronize_sched() can ensure that all interruptions that were active when synchronize_sched() was called are done, but only if CONFIG_PREEMPT=n. So, this version -of kprobe optimization supports only kernels with CONFIG_PREEMPT=n.(**) +of kprobe optimization supports only kernels with CONFIG_PREEMPT=n [4]_. After that, the Kprobe-optimizer calls stop_machine() to replace the optimized region with a jump instruction to the detour buffer, using text_poke_smp(). -1.4.6 Unoptimization +Unoptimization +^^^^^^^^^^^^^^ When an optimized kprobe is unregistered, disabled, or blocked by another kprobe, it will be unoptimized. If this happens before @@ -263,15 +286,15 @@ optimized list. If the optimization has been done, the jump is replaced with the original code (except for an int3 breakpoint in the first byte) by using text_poke_smp(). -(*)Please imagine that the 2nd instruction is interrupted and then -the optimizer replaces the 2nd instruction with the jump *address* -while the interrupt handler is running. When the interrupt -returns to original address, there is no valid instruction, -and it causes an unexpected result. +.. [3] Please imagine that the 2nd instruction is interrupted and then + the optimizer replaces the 2nd instruction with the jump *address* + while the interrupt handler is running. When the interrupt + returns to original address, there is no valid instruction, + and it causes an unexpected result. -(**)This optimization-safety checking may be replaced with the -stop-machine method that ksplice uses for supporting a CONFIG_PREEMPT=y -kernel. +.. [4] This optimization-safety checking may be replaced with the + stop-machine method that ksplice uses for supporting a CONFIG_PREEMPT=y + kernel. NOTE for geeks: The jump optimization changes the kprobe's pre_handler behavior. @@ -280,11 +303,17 @@ path by changing regs->ip and returning 1. However, when the probe is optimized, that modification is ignored. Thus, if you want to tweak the kernel's execution path, you need to suppress optimization, using one of the following techniques: + - Specify an empty function for the kprobe's post_handler or break_handler. - or + +or + - Execute 'sysctl -w debug.kprobes_optimization=n' -1.5 Blacklist +.. _kprobes_blacklist: + +Blacklist +--------- Kprobes can probe most of the kernel except itself. This means that there are some functions where kprobes cannot probe. Probing @@ -297,7 +326,10 @@ to specify a blacklisted function. Kprobes checks the given probe address against the blacklist and rejects registering it, if the given address is in the blacklist. -2. Architectures Supported +.. _kprobes_archs_supported: + +Architectures Supported +======================= Kprobes, jprobes, and return probes are implemented on the following architectures: @@ -312,7 +344,8 @@ architectures: - mips - s390 -3. Configuring Kprobes +Configuring Kprobes +=================== When configuring the kernel using make menuconfig/xconfig/oldconfig, ensure that CONFIG_KPROBES is set to "y". Under "General setup", look @@ -331,7 +364,8 @@ it useful to "Compile the kernel with debug info" (CONFIG_DEBUG_INFO), so you can use "objdump -d -l vmlinux" to see the source-to-object code mapping. -4. API Reference +API Reference +============= The Kprobes API includes a "register" function and an "unregister" function for each type of probe. The API also includes "register_*probes" @@ -340,10 +374,13 @@ Here are terse, mini-man-page specifications for these functions and the associated probe handlers that you'll write. See the files in the samples/kprobes/ sub-directory for examples. -4.1 register_kprobe +register_kprobe +--------------- + +:: -#include <linux/kprobes.h> -int register_kprobe(struct kprobe *kp); + #include <linux/kprobes.h> + int register_kprobe(struct kprobe *kp); Sets a breakpoint at the address kp->addr. When the breakpoint is hit, Kprobes calls kp->pre_handler. After the probed instruction @@ -354,61 +391,68 @@ kp->fault_handler. Any or all handlers can be NULL. If kp->flags is set KPROBE_FLAG_DISABLED, that kp will be registered but disabled, so, its handlers aren't hit until calling enable_kprobe(kp). -NOTE: -1. With the introduction of the "symbol_name" field to struct kprobe, -the probepoint address resolution will now be taken care of by the kernel. -The following will now work: +.. note:: + + 1. With the introduction of the "symbol_name" field to struct kprobe, + the probepoint address resolution will now be taken care of by the kernel. + The following will now work:: kp.symbol_name = "symbol_name"; -(64-bit powerpc intricacies such as function descriptors are handled -transparently) + (64-bit powerpc intricacies such as function descriptors are handled + transparently) -2. Use the "offset" field of struct kprobe if the offset into the symbol -to install a probepoint is known. This field is used to calculate the -probepoint. + 2. Use the "offset" field of struct kprobe if the offset into the symbol + to install a probepoint is known. This field is used to calculate the + probepoint. -3. Specify either the kprobe "symbol_name" OR the "addr". If both are -specified, kprobe registration will fail with -EINVAL. + 3. Specify either the kprobe "symbol_name" OR the "addr". If both are + specified, kprobe registration will fail with -EINVAL. -4. With CISC architectures (such as i386 and x86_64), the kprobes code -does not validate if the kprobe.addr is at an instruction boundary. -Use "offset" with caution. + 4. With CISC architectures (such as i386 and x86_64), the kprobes code + does not validate if the kprobe.addr is at an instruction boundary. + Use "offset" with caution. register_kprobe() returns 0 on success, or a negative errno otherwise. -User's pre-handler (kp->pre_handler): -#include <linux/kprobes.h> -#include <linux/ptrace.h> -int pre_handler(struct kprobe *p, struct pt_regs *regs); +User's pre-handler (kp->pre_handler):: + + #include <linux/kprobes.h> + #include <linux/ptrace.h> + int pre_handler(struct kprobe *p, struct pt_regs *regs); Called with p pointing to the kprobe associated with the breakpoint, and regs pointing to the struct containing the registers saved when the breakpoint was hit. Return 0 here unless you're a Kprobes geek. -User's post-handler (kp->post_handler): -#include <linux/kprobes.h> -#include <linux/ptrace.h> -void post_handler(struct kprobe *p, struct pt_regs *regs, - unsigned long flags); +User's post-handler (kp->post_handler):: + + #include <linux/kprobes.h> + #include <linux/ptrace.h> + void post_handler(struct kprobe *p, struct pt_regs *regs, + unsigned long flags); p and regs are as described for the pre_handler. flags always seems to be zero. -User's fault-handler (kp->fault_handler): -#include <linux/kprobes.h> -#include <linux/ptrace.h> -int fault_handler(struct kprobe *p, struct pt_regs *regs, int trapnr); +User's fault-handler (kp->fault_handler):: + + #include <linux/kprobes.h> + #include <linux/ptrace.h> + int fault_handler(struct kprobe *p, struct pt_regs *regs, int trapnr); p and regs are as described for the pre_handler. trapnr is the architecture-specific trap number associated with the fault (e.g., on i386, 13 for a general protection fault or 14 for a page fault). Returns 1 if it successfully handled the exception. -4.2 register_jprobe +register_jprobe +--------------- -#include <linux/kprobes.h> -int register_jprobe(struct jprobe *jp) +:: + + #include <linux/kprobes.h> + int register_jprobe(struct jprobe *jp) Sets a breakpoint at the address jp->kp.addr, which must be the address of the first instruction of a function. When the breakpoint is hit, @@ -423,10 +467,13 @@ declaration must match. register_jprobe() returns 0 on success, or a negative errno otherwise. -4.3 register_kretprobe +register_kretprobe +------------------ + +:: -#include <linux/kprobes.h> -int register_kretprobe(struct kretprobe *rp); + #include <linux/kprobes.h> + int register_kretprobe(struct kretprobe *rp); Establishes a return probe for the function whose address is rp->kp.addr. When that function returns, Kprobes calls rp->handler. @@ -436,14 +483,17 @@ register_kretprobe(); see "How Does a Return Probe Work?" for details. register_kretprobe() returns 0 on success, or a negative errno otherwise. -User's return-probe handler (rp->handler): -#include <linux/kprobes.h> -#include <linux/ptrace.h> -int kretprobe_handler(struct kretprobe_instance *ri, struct pt_regs *regs); +User's return-probe handler (rp->handler):: + + #include <linux/kprobes.h> + #include <linux/ptrace.h> + int kretprobe_handler(struct kretprobe_instance *ri, + struct pt_regs *regs); regs is as described for kprobe.pre_handler. ri points to the kretprobe_instance object, of which the following fields may be of interest: + - ret_addr: the return address - rp: points to the corresponding kretprobe object - task: points to the corresponding task struct @@ -456,74 +506,94 @@ the architecture's ABI. The handler's return value is currently ignored. -4.4 unregister_*probe +unregister_*probe +------------------ + +:: -#include <linux/kprobes.h> -void unregister_kprobe(struct kprobe *kp); -void unregister_jprobe(struct jprobe *jp); -void unregister_kretprobe(struct kretprobe *rp); + #include <linux/kprobes.h> + void unregister_kprobe(struct kprobe *kp); + void unregister_jprobe(struct jprobe *jp); + void unregister_kretprobe(struct kretprobe *rp); Removes the specified probe. The unregister function can be called at any time after the probe has been registered. -NOTE: -If the functions find an incorrect probe (ex. an unregistered probe), -they clear the addr field of the probe. +.. note:: + + If the functions find an incorrect probe (ex. an unregistered probe), + they clear the addr field of the probe. + +register_*probes +---------------- -4.5 register_*probes +:: -#include <linux/kprobes.h> -int register_kprobes(struct kprobe **kps, int num); -int register_kretprobes(struct kretprobe **rps, int num); -int register_jprobes(struct jprobe **jps, int num); + #include <linux/kprobes.h> + int register_kprobes(struct kprobe **kps, int num); + int register_kretprobes(struct kretprobe **rps, int num); + int register_jprobes(struct jprobe **jps, int num); Registers each of the num probes in the specified array. If any error occurs during registration, all probes in the array, up to the bad probe, are safely unregistered before the register_*probes function returns. -- kps/rps/jps: an array of pointers to *probe data structures + +- kps/rps/jps: an array of pointers to ``*probe`` data structures - num: the number of the array entries. -NOTE: -You have to allocate(or define) an array of pointers and set all -of the array entries before using these functions. +.. note:: + + You have to allocate(or define) an array of pointers and set all + of the array entries before using these functions. -4.6 unregister_*probes +unregister_*probes +------------------ -#include <linux/kprobes.h> -void unregister_kprobes(struct kprobe **kps, int num); -void unregister_kretprobes(struct kretprobe **rps, int num); -void unregister_jprobes(struct jprobe **jps, int num); +:: + + #include <linux/kprobes.h> + void unregister_kprobes(struct kprobe **kps, int num); + void unregister_kretprobes(struct kretprobe **rps, int num); + void unregister_jprobes(struct jprobe **jps, int num); Removes each of the num probes in the specified array at once. -NOTE: -If the functions find some incorrect probes (ex. unregistered -probes) in the specified array, they clear the addr field of those -incorrect probes. However, other probes in the array are -unregistered correctly. +.. note:: + + If the functions find some incorrect probes (ex. unregistered + probes) in the specified array, they clear the addr field of those + incorrect probes. However, other probes in the array are + unregistered correctly. -4.7 disable_*probe +disable_*probe +-------------- -#include <linux/kprobes.h> -int disable_kprobe(struct kprobe *kp); -int disable_kretprobe(struct kretprobe *rp); -int disable_jprobe(struct jprobe *jp); +:: -Temporarily disables the specified *probe. You can enable it again by using + #include <linux/kprobes.h> + int disable_kprobe(struct kprobe *kp); + int disable_kretprobe(struct kretprobe *rp); + int disable_jprobe(struct jprobe *jp); + +Temporarily disables the specified ``*probe``. You can enable it again by using enable_*probe(). You must specify the probe which has been registered. -4.8 enable_*probe +enable_*probe +------------- + +:: -#include <linux/kprobes.h> -int enable_kprobe(struct kprobe *kp); -int enable_kretprobe(struct kretprobe *rp); -int enable_jprobe(struct jprobe *jp); + #include <linux/kprobes.h> + int enable_kprobe(struct kprobe *kp); + int enable_kretprobe(struct kretprobe *rp); + int enable_jprobe(struct jprobe *jp); -Enables *probe which has been disabled by disable_*probe(). You must specify +Enables ``*probe`` which has been disabled by disable_*probe(). You must specify the probe which has been registered. -5. Kprobes Features and Limitations +Kprobes Features and Limitations +================================ Kprobes allows multiple probes at the same address. Currently, however, there cannot be multiple jprobes on the same function at @@ -538,7 +608,7 @@ are discussed in this section. The register_*probe functions will return -EINVAL if you attempt to install a probe in the code that implements Kprobes (mostly -kernel/kprobes.c and arch/*/kernel/kprobes.c, but also functions such +kernel/kprobes.c and ``arch/*/kernel/kprobes.c``, but also functions such as do_page_fault and notifier_call_chain). If you install a probe in an inline-able function, Kprobes makes @@ -602,19 +672,21 @@ explain it, we introduce some terminology. Imagine a 3-instruction sequence consisting of a two 2-byte instructions and one 3-byte instruction. - IA - | -[-2][-1][0][1][2][3][4][5][6][7] - [ins1][ins2][ ins3 ] - [<- DCR ->] - [<- JTPR ->] +:: -ins1: 1st Instruction -ins2: 2nd Instruction -ins3: 3rd Instruction -IA: Insertion Address -JTPR: Jump Target Prohibition Region -DCR: Detoured Code Region + IA + | + [-2][-1][0][1][2][3][4][5][6][7] + [ins1][ins2][ ins3 ] + [<- DCR ->] + [<- JTPR ->] + + ins1: 1st Instruction + ins2: 2nd Instruction + ins3: 3rd Instruction + IA: Insertion Address + JTPR: Jump Target Prohibition Region + DCR: Detoured Code Region The instructions in DCR are copied to the out-of-line buffer of the kprobe, because the bytes in DCR are replaced by @@ -628,7 +700,8 @@ d) DCR must not straddle the border between functions. Anyway, these limitations are checked by the in-kernel instruction decoder, so you don't need to worry about that. -6. Probe Overhead +Probe Overhead +============== On a typical CPU in use in 2005, a kprobe hit takes 0.5 to 1.0 microseconds to process. Specifically, a benchmark that hits the same @@ -638,70 +711,80 @@ return-probe hit typically takes 50-75% longer than a kprobe hit. When you have a return probe set on a function, adding a kprobe at the entry to that function adds essentially no overhead. -Here are sample overhead figures (in usec) for different architectures. -k = kprobe; j = jprobe; r = return probe; kr = kprobe + return probe -on same function; jr = jprobe + return probe on same function +Here are sample overhead figures (in usec) for different architectures:: + + k = kprobe; j = jprobe; r = return probe; kr = kprobe + return probe + on same function; jr = jprobe + return probe on same function:: -i386: Intel Pentium M, 1495 MHz, 2957.31 bogomips -k = 0.57 usec; j = 1.00; r = 0.92; kr = 0.99; jr = 1.40 + i386: Intel Pentium M, 1495 MHz, 2957.31 bogomips + k = 0.57 usec; j = 1.00; r = 0.92; kr = 0.99; jr = 1.40 -x86_64: AMD Opteron 246, 1994 MHz, 3971.48 bogomips -k = 0.49 usec; j = 0.76; r = 0.80; kr = 0.82; jr = 1.07 + x86_64: AMD Opteron 246, 1994 MHz, 3971.48 bogomips + k = 0.49 usec; j = 0.76; r = 0.80; kr = 0.82; jr = 1.07 -ppc64: POWER5 (gr), 1656 MHz (SMT disabled, 1 virtual CPU per physical CPU) -k = 0.77 usec; j = 1.31; r = 1.26; kr = 1.45; jr = 1.99 + ppc64: POWER5 (gr), 1656 MHz (SMT disabled, 1 virtual CPU per physical CPU) + k = 0.77 usec; j = 1.31; r = 1.26; kr = 1.45; jr = 1.99 -6.1 Optimized Probe Overhead +Optimized Probe Overhead +------------------------ Typically, an optimized kprobe hit takes 0.07 to 0.1 microseconds to -process. Here are sample overhead figures (in usec) for x86 architectures. -k = unoptimized kprobe, b = boosted (single-step skipped), o = optimized kprobe, -r = unoptimized kretprobe, rb = boosted kretprobe, ro = optimized kretprobe. +process. Here are sample overhead figures (in usec) for x86 architectures:: -i386: Intel(R) Xeon(R) E5410, 2.33GHz, 4656.90 bogomips -k = 0.80 usec; b = 0.33; o = 0.05; r = 1.10; rb = 0.61; ro = 0.33 + k = unoptimized kprobe, b = boosted (single-step skipped), o = optimized kprobe, + r = unoptimized kretprobe, rb = boosted kretprobe, ro = optimized kretprobe. -x86-64: Intel(R) Xeon(R) E5410, 2.33GHz, 4656.90 bogomips -k = 0.99 usec; b = 0.43; o = 0.06; r = 1.24; rb = 0.68; ro = 0.30 + i386: Intel(R) Xeon(R) E5410, 2.33GHz, 4656.90 bogomips + k = 0.80 usec; b = 0.33; o = 0.05; r = 1.10; rb = 0.61; ro = 0.33 -7. TODO + x86-64: Intel(R) Xeon(R) E5410, 2.33GHz, 4656.90 bogomips + k = 0.99 usec; b = 0.43; o = 0.06; r = 1.24; rb = 0.68; ro = 0.30 + +TODO +==== a. SystemTap (http://sourceware.org/systemtap): Provides a simplified -programming interface for probe-based instrumentation. Try it out. + programming interface for probe-based instrumentation. Try it out. b. Kernel return probes for sparc64. c. Support for other architectures. d. User-space probes. e. Watchpoint probes (which fire on data references). -8. Kprobes Example +Kprobes Example +=============== See samples/kprobes/kprobe_example.c -9. Jprobes Example +Jprobes Example +=============== See samples/kprobes/jprobe_example.c -10. Kretprobes Example +Kretprobes Example +================== See samples/kprobes/kretprobe_example.c For additional information on Kprobes, refer to the following URLs: -http://www-106.ibm.com/developerworks/library/l-kprobes.html?ca=dgr-lnxw42Kprobe -http://www.redhat.com/magazine/005mar05/features/kprobes/ -http://www-users.cs.umn.edu/~boutcher/kprobes/ -http://www.linuxsymposium.org/2006/linuxsymposium_procv2.pdf (pages 101-115) + +- http://www-106.ibm.com/developerworks/library/l-kprobes.html?ca=dgr-lnxw42Kprobe +- http://www.redhat.com/magazine/005mar05/features/kprobes/ +- http://www-users.cs.umn.edu/~boutcher/kprobes/ +- http://www.linuxsymposium.org/2006/linuxsymposium_procv2.pdf (pages 101-115) -Appendix A: The kprobes debugfs interface +The kprobes debugfs interface +============================= + With recent kernels (> 2.6.20) the list of registered kprobes is visible under the /sys/kernel/debug/kprobes/ directory (assuming debugfs is mounted at //sys/kernel/debug). -/sys/kernel/debug/kprobes/list: Lists all registered probes on the system +/sys/kernel/debug/kprobes/list: Lists all registered probes on the system:: -c015d71a k vfs_read+0x0 -c011a316 j do_fork+0x0 -c03dedc5 r tcp_v4_rcv+0x0 + c015d71a k vfs_read+0x0 + c011a316 j do_fork+0x0 + c03dedc5 r tcp_v4_rcv+0x0 The first column provides the kernel address where the probe is inserted. The second column identifies the type of probe (k - kprobe, r - kretprobe @@ -725,17 +808,19 @@ change each probe's disabling state. This means that disabled kprobes (marked [DISABLED]) will be not enabled if you turn ON all kprobes by this knob. -Appendix B: The kprobes sysctl interface +The kprobes sysctl interface +============================ /proc/sys/debug/kprobes-optimization: Turn kprobes optimization ON/OFF. When CONFIG_OPTPROBES=y, this sysctl interface appears and it provides a knob to globally and forcibly turn jump optimization (see section -1.4) ON or OFF. By default, jump optimization is allowed (ON). -If you echo "0" to this file or set "debug.kprobes_optimization" to -0 via sysctl, all optimized probes will be unoptimized, and any new -probes registered after that will not be optimized. Note that this -knob *changes* the optimized state. This means that optimized probes -(marked [OPTIMIZED]) will be unoptimized ([OPTIMIZED] tag will be +:ref:`kprobes_jump_optimization`) ON or OFF. By default, jump optimization +is allowed (ON). If you echo "0" to this file or set +"debug.kprobes_optimization" to 0 via sysctl, all optimized probes will be +unoptimized, and any new probes registered after that will not be optimized. + +Note that this knob *changes* the optimized state. This means that optimized +probes (marked [OPTIMIZED]) will be unoptimized ([OPTIMIZED] tag will be removed). If the knob is turned on, they will be optimized again. diff --git a/Documentation/kref.txt b/Documentation/kref.txt index d26a27ca964d..3af384156d7e 100644 --- a/Documentation/kref.txt +++ b/Documentation/kref.txt @@ -1,24 +1,42 @@ +=================================================== +Adding reference counters (krefs) to kernel objects +=================================================== + +:Author: Corey Minyard <minyard@acm.org> +:Author: Thomas Hellstrom <thellstrom@vmware.com> + +A lot of this was lifted from Greg Kroah-Hartman's 2004 OLS paper and +presentation on krefs, which can be found at: + + - http://www.kroah.com/linux/talks/ols_2004_kref_paper/Reprint-Kroah-Hartman-OLS2004.pdf + - http://www.kroah.com/linux/talks/ols_2004_kref_talk/ + +Introduction +============ krefs allow you to add reference counters to your objects. If you have objects that are used in multiple places and passed around, and you don't have refcounts, your code is almost certainly broken. If you want refcounts, krefs are the way to go. -To use a kref, add one to your data structures like: +To use a kref, add one to your data structures like:: -struct my_data -{ + struct my_data + { . . struct kref refcount; . . -}; + }; The kref can occur anywhere within the data structure. +Initialization +============== + You must initialize the kref after you allocate it. To do this, call -kref_init as so: +kref_init as so:: struct my_data *data; @@ -29,18 +47,25 @@ kref_init as so: This sets the refcount in the kref to 1. +Kref rules +========== + Once you have an initialized kref, you must follow the following rules: 1) If you make a non-temporary copy of a pointer, especially if it can be passed to another thread of execution, you must - increment the refcount with kref_get() before passing it off: + increment the refcount with kref_get() before passing it off:: + kref_get(&data->refcount); + If you already have a valid pointer to a kref-ed structure (the refcount cannot go to zero) you may do this without a lock. -2) When you are done with a pointer, you must call kref_put(): +2) When you are done with a pointer, you must call kref_put():: + kref_put(&data->refcount, data_release); + If this is the last reference to the pointer, the release routine will be called. If the code never tries to get a valid pointer to a kref-ed structure without already @@ -53,25 +78,25 @@ rules: structure must remain valid during the kref_get(). For example, if you allocate some data and then pass it to another -thread to process: +thread to process:: -void data_release(struct kref *ref) -{ + void data_release(struct kref *ref) + { struct my_data *data = container_of(ref, struct my_data, refcount); kfree(data); -} + } -void more_data_handling(void *cb_data) -{ + void more_data_handling(void *cb_data) + { struct my_data *data = cb_data; . . do stuff with data here . kref_put(&data->refcount, data_release); -} + } -int my_data_handler(void) -{ + int my_data_handler(void) + { int rv = 0; struct my_data *data; struct task_struct *task; @@ -91,10 +116,10 @@ int my_data_handler(void) . . do stuff with data here . - out: + out: kref_put(&data->refcount, data_release); return rv; -} + } This way, it doesn't matter what order the two threads handle the data, the kref_put() handles knowing when the data is not referenced @@ -104,7 +129,7 @@ put needs no lock because nothing tries to get the data without already holding a pointer. Note that the "before" in rule 1 is very important. You should never -do something like: +do something like:: task = kthread_run(more_data_handling, data, "more_data_handling"); if (task == ERR_PTR(-ENOMEM)) { @@ -124,14 +149,14 @@ bad style. Don't do it. There are some situations where you can optimize the gets and puts. For instance, if you are done with an object and enqueuing it for something else or passing it off to something else, there is no reason -to do a get then a put: +to do a get then a put:: /* Silly extra get and put */ kref_get(&obj->ref); enqueue(obj); kref_put(&obj->ref, obj_cleanup); -Just do the enqueue. A comment about this is always welcome: +Just do the enqueue. A comment about this is always welcome:: enqueue(obj); /* We are done with obj, so we pass our refcount off @@ -142,109 +167,99 @@ instance, you have a list of items that are each kref-ed, and you wish to get the first one. You can't just pull the first item off the list and kref_get() it. That violates rule 3 because you are not already holding a valid pointer. You must add a mutex (or some other lock). -For instance: - -static DEFINE_MUTEX(mutex); -static LIST_HEAD(q); -struct my_data -{ - struct kref refcount; - struct list_head link; -}; - -static struct my_data *get_entry() -{ - struct my_data *entry = NULL; - mutex_lock(&mutex); - if (!list_empty(&q)) { - entry = container_of(q.next, struct my_data, link); - kref_get(&entry->refcount); +For instance:: + + static DEFINE_MUTEX(mutex); + static LIST_HEAD(q); + struct my_data + { + struct kref refcount; + struct list_head link; + }; + + static struct my_data *get_entry() + { + struct my_data *entry = NULL; + mutex_lock(&mutex); + if (!list_empty(&q)) { + entry = container_of(q.next, struct my_data, link); + kref_get(&entry->refcount); + } + mutex_unlock(&mutex); + return entry; } - mutex_unlock(&mutex); - return entry; -} -static void release_entry(struct kref *ref) -{ - struct my_data *entry = container_of(ref, struct my_data, refcount); + static void release_entry(struct kref *ref) + { + struct my_data *entry = container_of(ref, struct my_data, refcount); - list_del(&entry->link); - kfree(entry); -} + list_del(&entry->link); + kfree(entry); + } -static void put_entry(struct my_data *entry) -{ - mutex_lock(&mutex); - kref_put(&entry->refcount, release_entry); - mutex_unlock(&mutex); -} + static void put_entry(struct my_data *entry) + { + mutex_lock(&mutex); + kref_put(&entry->refcount, release_entry); + mutex_unlock(&mutex); + } The kref_put() return value is useful if you do not want to hold the lock during the whole release operation. Say you didn't want to call kfree() with the lock held in the example above (since it is kind of -pointless to do so). You could use kref_put() as follows: +pointless to do so). You could use kref_put() as follows:: -static void release_entry(struct kref *ref) -{ - /* All work is done after the return from kref_put(). */ -} + static void release_entry(struct kref *ref) + { + /* All work is done after the return from kref_put(). */ + } -static void put_entry(struct my_data *entry) -{ - mutex_lock(&mutex); - if (kref_put(&entry->refcount, release_entry)) { - list_del(&entry->link); - mutex_unlock(&mutex); - kfree(entry); - } else - mutex_unlock(&mutex); -} + static void put_entry(struct my_data *entry) + { + mutex_lock(&mutex); + if (kref_put(&entry->refcount, release_entry)) { + list_del(&entry->link); + mutex_unlock(&mutex); + kfree(entry); + } else + mutex_unlock(&mutex); + } This is really more useful if you have to call other routines as part of the free operations that could take a long time or might claim the same lock. Note that doing everything in the release routine is still preferred as it is a little neater. - -Corey Minyard <minyard@acm.org> - -A lot of this was lifted from Greg Kroah-Hartman's 2004 OLS paper and -presentation on krefs, which can be found at: - http://www.kroah.com/linux/talks/ols_2004_kref_paper/Reprint-Kroah-Hartman-OLS2004.pdf -and: - http://www.kroah.com/linux/talks/ols_2004_kref_talk/ - - The above example could also be optimized using kref_get_unless_zero() in -the following way: - -static struct my_data *get_entry() -{ - struct my_data *entry = NULL; - mutex_lock(&mutex); - if (!list_empty(&q)) { - entry = container_of(q.next, struct my_data, link); - if (!kref_get_unless_zero(&entry->refcount)) - entry = NULL; +the following way:: + + static struct my_data *get_entry() + { + struct my_data *entry = NULL; + mutex_lock(&mutex); + if (!list_empty(&q)) { + entry = container_of(q.next, struct my_data, link); + if (!kref_get_unless_zero(&entry->refcount)) + entry = NULL; + } + mutex_unlock(&mutex); + return entry; } - mutex_unlock(&mutex); - return entry; -} -static void release_entry(struct kref *ref) -{ - struct my_data *entry = container_of(ref, struct my_data, refcount); + static void release_entry(struct kref *ref) + { + struct my_data *entry = container_of(ref, struct my_data, refcount); - mutex_lock(&mutex); - list_del(&entry->link); - mutex_unlock(&mutex); - kfree(entry); -} + mutex_lock(&mutex); + list_del(&entry->link); + mutex_unlock(&mutex); + kfree(entry); + } -static void put_entry(struct my_data *entry) -{ - kref_put(&entry->refcount, release_entry); -} + static void put_entry(struct my_data *entry) + { + kref_put(&entry->refcount, release_entry); + } Which is useful to remove the mutex lock around kref_put() in put_entry(), but it's important that kref_get_unless_zero is enclosed in the same critical @@ -254,51 +269,51 @@ Note that it is illegal to use kref_get_unless_zero without checking its return value. If you are sure (by already having a valid pointer) that kref_get_unless_zero() will return true, then use kref_get() instead. -The function kref_get_unless_zero also makes it possible to use rcu -locking for lookups in the above example: +Krefs and RCU +============= -struct my_data -{ - struct rcu_head rhead; - . - struct kref refcount; - . - . -}; - -static struct my_data *get_entry_rcu() -{ - struct my_data *entry = NULL; - rcu_read_lock(); - if (!list_empty(&q)) { - entry = container_of(q.next, struct my_data, link); - if (!kref_get_unless_zero(&entry->refcount)) - entry = NULL; +The function kref_get_unless_zero also makes it possible to use rcu +locking for lookups in the above example:: + + struct my_data + { + struct rcu_head rhead; + . + struct kref refcount; + . + . + }; + + static struct my_data *get_entry_rcu() + { + struct my_data *entry = NULL; + rcu_read_lock(); + if (!list_empty(&q)) { + entry = container_of(q.next, struct my_data, link); + if (!kref_get_unless_zero(&entry->refcount)) + entry = NULL; + } + rcu_read_unlock(); + return entry; } - rcu_read_unlock(); - return entry; -} -static void release_entry_rcu(struct kref *ref) -{ - struct my_data *entry = container_of(ref, struct my_data, refcount); + static void release_entry_rcu(struct kref *ref) + { + struct my_data *entry = container_of(ref, struct my_data, refcount); - mutex_lock(&mutex); - list_del_rcu(&entry->link); - mutex_unlock(&mutex); - kfree_rcu(entry, rhead); -} + mutex_lock(&mutex); + list_del_rcu(&entry->link); + mutex_unlock(&mutex); + kfree_rcu(entry, rhead); + } -static void put_entry(struct my_data *entry) -{ - kref_put(&entry->refcount, release_entry_rcu); -} + static void put_entry(struct my_data *entry) + { + kref_put(&entry->refcount, release_entry_rcu); + } But note that the struct kref member needs to remain in valid memory for a rcu grace period after release_entry_rcu was called. That can be accomplished by using kfree_rcu(entry, rhead) as done above, or by calling synchronize_rcu() before using kfree, but note that synchronize_rcu() may sleep for a substantial amount of time. - - -Thomas Hellstrom <thellstrom@vmware.com> diff --git a/Documentation/ldm.txt b/Documentation/ldm.txt index 4f80edd14d0a..12c571368e73 100644 --- a/Documentation/ldm.txt +++ b/Documentation/ldm.txt @@ -1,9 +1,9 @@ +========================================== +LDM - Logical Disk Manager (Dynamic Disks) +========================================== - LDM - Logical Disk Manager (Dynamic Disks) - ------------------------------------------ - -Originally Written by FlatCap - Richard Russon <ldm@flatcap.org>. -Last Updated by Anton Altaparmakov on 30 March 2007 for Windows Vista. +:Author: Originally Written by FlatCap - Richard Russon <ldm@flatcap.org>. +:Last Updated: Anton Altaparmakov on 30 March 2007 for Windows Vista. Overview -------- @@ -37,24 +37,36 @@ Example ------- Below we have a 50MiB disk, divided into seven partitions. -N.B. The missing 1MiB at the end of the disk is where the LDM database is - stored. - - Device | Offset Bytes Sectors MiB | Size Bytes Sectors MiB - -------+----------------------------+--------------------------- - hda | 0 0 0 | 52428800 102400 50 - hda1 | 51380224 100352 49 | 1048576 2048 1 - hda2 | 16384 32 0 | 6979584 13632 6 - hda3 | 6995968 13664 6 | 10485760 20480 10 - hda4 | 17481728 34144 16 | 4194304 8192 4 - hda5 | 21676032 42336 20 | 5242880 10240 5 - hda6 | 26918912 52576 25 | 10485760 20480 10 - hda7 | 37404672 73056 35 | 13959168 27264 13 + +.. note:: + + The missing 1MiB at the end of the disk is where the LDM database is + stored. + ++-------++--------------+---------+-----++--------------+---------+----+ +|Device || Offset Bytes | Sectors | MiB || Size Bytes | Sectors | MiB| ++=======++==============+=========+=====++==============+=========+====+ +|hda || 0 | 0 | 0 || 52428800 | 102400 | 50| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda1 || 51380224 | 100352 | 49 || 1048576 | 2048 | 1| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda2 || 16384 | 32 | 0 || 6979584 | 13632 | 6| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda3 || 6995968 | 13664 | 6 || 10485760 | 20480 | 10| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda4 || 17481728 | 34144 | 16 || 4194304 | 8192 | 4| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda5 || 21676032 | 42336 | 20 || 5242880 | 10240 | 5| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda6 || 26918912 | 52576 | 25 || 10485760 | 20480 | 10| ++-------++--------------+---------+-----++--------------+---------+----+ +|hda7 || 37404672 | 73056 | 35 || 13959168 | 27264 | 13| ++-------++--------------+---------+-----++--------------+---------+----+ The LDM Database may not store the partitions in the order that they appear on disk, but the driver will sort them. -When Linux boots, you will see something like: +When Linux boots, you will see something like:: hda: 102400 sectors w/32KiB Cache, CHS=50/64/32 hda: [LDM] hda1 hda2 hda3 hda4 hda5 hda6 hda7 @@ -65,13 +77,13 @@ Compiling LDM Support To enable LDM, choose the following two options: - "Advanced partition selection" CONFIG_PARTITION_ADVANCED - "Windows Logical Disk Manager (Dynamic Disk) support" CONFIG_LDM_PARTITION + - "Advanced partition selection" CONFIG_PARTITION_ADVANCED + - "Windows Logical Disk Manager (Dynamic Disk) support" CONFIG_LDM_PARTITION If you believe the driver isn't working as it should, you can enable the extra debugging code. This will produce a LOT of output. The option is: - "Windows LDM extra logging" CONFIG_LDM_DEBUG + - "Windows LDM extra logging" CONFIG_LDM_DEBUG N.B. The partition code cannot be compiled as a module. diff --git a/Documentation/lockup-watchdogs.txt b/Documentation/lockup-watchdogs.txt index c8b8378513d6..290840c160af 100644 --- a/Documentation/lockup-watchdogs.txt +++ b/Documentation/lockup-watchdogs.txt @@ -30,7 +30,8 @@ timeout is set through the confusingly named "kernel.panic" sysctl), to cause the system to reboot automatically after a specified amount of time. -=== Implementation === +Implementation +============== The soft and hard lockup detectors are built on top of the hrtimer and perf subsystems, respectively. A direct consequence of this is that, diff --git a/Documentation/lzo.txt b/Documentation/lzo.txt index 285c54f66779..6fa6a93d0949 100644 --- a/Documentation/lzo.txt +++ b/Documentation/lzo.txt @@ -1,8 +1,9 @@ - +=========================================================== LZO stream format as understood by Linux's LZO decompressor =========================================================== Introduction +============ This is not a specification. No specification seems to be publicly available for the LZO stream format. This document describes what input format the LZO @@ -14,12 +15,13 @@ Introduction for future bug reports. Description +=========== The stream is composed of a series of instructions, operands, and data. The instructions consist in a few bits representing an opcode, and bits forming the operands for the instruction, whose size and position depend on the opcode and on the number of literals copied by previous instruction. The - operands are used to indicate : + operands are used to indicate: - a distance when copying data from the dictionary (past output buffer) - a length (number of bytes to copy from dictionary) @@ -38,7 +40,7 @@ Description of bits in the operand. If the number of bits isn't enough to represent the length, up to 255 may be added in increments by consuming more bytes with a rate of at most 255 per extra byte (thus the compression ratio cannot exceed - around 255:1). The variable length encoding using #bits is always the same : + around 255:1). The variable length encoding using #bits is always the same:: length = byte & ((1 << #bits) - 1) if (!length) { @@ -67,15 +69,19 @@ Description instruction may encode this distance (0001HLLL), it takes one LE16 operand for the distance, thus requiring 3 bytes. - IMPORTANT NOTE : in the code some length checks are missing because certain - instructions are called under the assumption that a certain number of bytes - follow because it has already been guaranteed before parsing the instructions. - They just have to "refill" this credit if they consume extra bytes. This is - an implementation design choice independent on the algorithm or encoding. + .. important:: + + In the code some length checks are missing because certain instructions + are called under the assumption that a certain number of bytes follow + because it has already been guaranteed before parsing the instructions. + They just have to "refill" this credit if they consume extra bytes. This + is an implementation design choice independent on the algorithm or + encoding. Byte sequences +============== - First byte encoding : + First byte encoding:: 0..17 : follow regular instruction encoding, see below. It is worth noting that codes 16 and 17 will represent a block copy from @@ -91,7 +97,7 @@ Byte sequences state = 4 [ don't copy extra literals ] skip byte - Instruction encoding : + Instruction encoding:: 0 0 0 0 X X X X (0..15) Depends on the number of literals copied by the last instruction. @@ -156,6 +162,7 @@ Byte sequences distance = (H << 3) + D + 1 Authors +======= This document was written by Willy Tarreau <w@1wt.eu> on 2014/07/19 during an analysis of the decompression code available in Linux 3.16-rc5. The code is diff --git a/Documentation/mailbox.txt b/Documentation/mailbox.txt index 7ed371c85204..0ed95009cc30 100644 --- a/Documentation/mailbox.txt +++ b/Documentation/mailbox.txt @@ -1,7 +1,10 @@ - The Common Mailbox Framework - Jassi Brar <jaswinder.singh@linaro.org> +============================ +The Common Mailbox Framework +============================ - This document aims to help developers write client and controller +:Author: Jassi Brar <jaswinder.singh@linaro.org> + +This document aims to help developers write client and controller drivers for the API. But before we start, let us note that the client (especially) and controller drivers are likely going to be very platform specific because the remote firmware is likely to be @@ -13,14 +16,17 @@ similar copies of code written for each platform. Having said that, nothing prevents the remote f/w to also be Linux based and use the same api there. However none of that helps us locally because we only ever deal at client's protocol level. - Some of the choices made during implementation are the result of this + +Some of the choices made during implementation are the result of this peculiarity of this "common" framework. - Part 1 - Controller Driver (See include/linux/mailbox_controller.h) +Controller Driver (See include/linux/mailbox_controller.h) +========================================================== + - Allocate mbox_controller and the array of mbox_chan. +Allocate mbox_controller and the array of mbox_chan. Populate mbox_chan_ops, except peek_data() all are mandatory. The controller driver might know a message has been consumed by the remote by getting an IRQ or polling some hardware flag @@ -30,91 +36,94 @@ the controller driver should set via 'txdone_irq' or 'txdone_poll' or neither. - Part 2 - Client Driver (See include/linux/mailbox_client.h) +Client Driver (See include/linux/mailbox_client.h) +================================================== - The client might want to operate in blocking mode (synchronously + +The client might want to operate in blocking mode (synchronously send a message through before returning) or non-blocking/async mode (submit a message and a callback function to the API and return immediately). - -struct demo_client { - struct mbox_client cl; - struct mbox_chan *mbox; - struct completion c; - bool async; - /* ... */ -}; - -/* - * This is the handler for data received from remote. The behaviour is purely - * dependent upon the protocol. This is just an example. - */ -static void message_from_remote(struct mbox_client *cl, void *mssg) -{ - struct demo_client *dc = container_of(cl, struct demo_client, cl); - if (dc->async) { - if (is_an_ack(mssg)) { - /* An ACK to our last sample sent */ - return; /* Or do something else here */ - } else { /* A new message from remote */ - queue_req(mssg); +:: + + struct demo_client { + struct mbox_client cl; + struct mbox_chan *mbox; + struct completion c; + bool async; + /* ... */ + }; + + /* + * This is the handler for data received from remote. The behaviour is purely + * dependent upon the protocol. This is just an example. + */ + static void message_from_remote(struct mbox_client *cl, void *mssg) + { + struct demo_client *dc = container_of(cl, struct demo_client, cl); + if (dc->async) { + if (is_an_ack(mssg)) { + /* An ACK to our last sample sent */ + return; /* Or do something else here */ + } else { /* A new message from remote */ + queue_req(mssg); + } + } else { + /* Remote f/w sends only ACK packets on this channel */ + return; } - } else { - /* Remote f/w sends only ACK packets on this channel */ - return; } -} - -static void sample_sent(struct mbox_client *cl, void *mssg, int r) -{ - struct demo_client *dc = container_of(cl, struct demo_client, cl); - complete(&dc->c); -} - -static void client_demo(struct platform_device *pdev) -{ - struct demo_client *dc_sync, *dc_async; - /* The controller already knows async_pkt and sync_pkt */ - struct async_pkt ap; - struct sync_pkt sp; - - dc_sync = kzalloc(sizeof(*dc_sync), GFP_KERNEL); - dc_async = kzalloc(sizeof(*dc_async), GFP_KERNEL); - - /* Populate non-blocking mode client */ - dc_async->cl.dev = &pdev->dev; - dc_async->cl.rx_callback = message_from_remote; - dc_async->cl.tx_done = sample_sent; - dc_async->cl.tx_block = false; - dc_async->cl.tx_tout = 0; /* doesn't matter here */ - dc_async->cl.knows_txdone = false; /* depending upon protocol */ - dc_async->async = true; - init_completion(&dc_async->c); - - /* Populate blocking mode client */ - dc_sync->cl.dev = &pdev->dev; - dc_sync->cl.rx_callback = message_from_remote; - dc_sync->cl.tx_done = NULL; /* operate in blocking mode */ - dc_sync->cl.tx_block = true; - dc_sync->cl.tx_tout = 500; /* by half a second */ - dc_sync->cl.knows_txdone = false; /* depending upon protocol */ - dc_sync->async = false; - - /* ASync mailbox is listed second in 'mboxes' property */ - dc_async->mbox = mbox_request_channel(&dc_async->cl, 1); - /* Populate data packet */ - /* ap.xxx = 123; etc */ - /* Send async message to remote */ - mbox_send_message(dc_async->mbox, &ap); - - /* Sync mailbox is listed first in 'mboxes' property */ - dc_sync->mbox = mbox_request_channel(&dc_sync->cl, 0); - /* Populate data packet */ - /* sp.abc = 123; etc */ - /* Send message to remote in blocking mode */ - mbox_send_message(dc_sync->mbox, &sp); - /* At this point 'sp' has been sent */ - - /* Now wait for async chan to be done */ - wait_for_completion(&dc_async->c); -} + + static void sample_sent(struct mbox_client *cl, void *mssg, int r) + { + struct demo_client *dc = container_of(cl, struct demo_client, cl); + complete(&dc->c); + } + + static void client_demo(struct platform_device *pdev) + { + struct demo_client *dc_sync, *dc_async; + /* The controller already knows async_pkt and sync_pkt */ + struct async_pkt ap; + struct sync_pkt sp; + + dc_sync = kzalloc(sizeof(*dc_sync), GFP_KERNEL); + dc_async = kzalloc(sizeof(*dc_async), GFP_KERNEL); + + /* Populate non-blocking mode client */ + dc_async->cl.dev = &pdev->dev; + dc_async->cl.rx_callback = message_from_remote; + dc_async->cl.tx_done = sample_sent; + dc_async->cl.tx_block = false; + dc_async->cl.tx_tout = 0; /* doesn't matter here */ + dc_async->cl.knows_txdone = false; /* depending upon protocol */ + dc_async->async = true; + init_completion(&dc_async->c); + + /* Populate blocking mode client */ + dc_sync->cl.dev = &pdev->dev; + dc_sync->cl.rx_callback = message_from_remote; + dc_sync->cl.tx_done = NULL; /* operate in blocking mode */ + dc_sync->cl.tx_block = true; + dc_sync->cl.tx_tout = 500; /* by half a second */ + dc_sync->cl.knows_txdone = false; /* depending upon protocol */ + dc_sync->async = false; + + /* ASync mailbox is listed second in 'mboxes' property */ + dc_async->mbox = mbox_request_channel(&dc_async->cl, 1); + /* Populate data packet */ + /* ap.xxx = 123; etc */ + /* Send async message to remote */ + mbox_send_message(dc_async->mbox, &ap); + + /* Sync mailbox is listed first in 'mboxes' property */ + dc_sync->mbox = mbox_request_channel(&dc_sync->cl, 0); + /* Populate data packet */ + /* sp.abc = 123; etc */ + /* Send message to remote in blocking mode */ + mbox_send_message(dc_sync->mbox, &sp); + /* At this point 'sp' has been sent */ + + /* Now wait for async chan to be done */ + wait_for_completion(&dc_async->c); + } diff --git a/Documentation/memory-barriers.txt b/Documentation/memory-barriers.txt index c239a0cf4b1a..c4ddfcd5ee32 100644 --- a/Documentation/memory-barriers.txt +++ b/Documentation/memory-barriers.txt @@ -1876,8 +1876,8 @@ There are some more advanced barrier functions: This makes sure that the death mark on the object is perceived to be set *before* the reference counter is decremented. - See Documentation/atomic_ops.txt for more information. See the "Atomic - operations" subsection for information on where to use these. + See Documentation/core-api/atomic_ops.rst for more information. See the + "Atomic operations" subsection for information on where to use these. (*) lockless_dereference(); @@ -2584,7 +2584,7 @@ situations because on some CPUs the atomic instructions used imply full memory barriers, and so barrier instructions are superfluous in conjunction with them, and in such cases the special barrier primitives will be no-ops. -See Documentation/atomic_ops.txt for more information. +See Documentation/core-api/atomic_ops.rst for more information. ACCESSING DEVICES diff --git a/Documentation/memory-hotplug.txt b/Documentation/memory-hotplug.txt index 670f3ded0802..7f49ebf3ddb2 100644 --- a/Documentation/memory-hotplug.txt +++ b/Documentation/memory-hotplug.txt @@ -2,43 +2,48 @@ Memory Hotplug ============== -Created: Jul 28 2007 -Add description of notifier of memory hotplug Oct 11 2007 +:Created: Jul 28 2007 +:Updated: Add description of notifier of memory hotplug: Oct 11 2007 This document is about memory hotplug including how-to-use and current status. Because Memory Hotplug is still under development, contents of this text will be changed often. -1. Introduction - 1.1 purpose of memory hotplug - 1.2. Phases of memory hotplug - 1.3. Unit of Memory online/offline operation -2. Kernel Configuration -3. sysfs files for memory hotplug -4. Physical memory hot-add phase - 4.1 Hardware(Firmware) Support - 4.2 Notify memory hot-add event by hand -5. Logical Memory hot-add phase - 5.1. State of memory - 5.2. How to online memory -6. Logical memory remove - 6.1 Memory offline and ZONE_MOVABLE - 6.2. How to offline memory -7. Physical memory remove -8. Memory hotplug event notifier -9. Future Work List - -Note(1): x86_64's has special implementation for memory hotplug. - This text does not describe it. -Note(2): This text assumes that sysfs is mounted at /sys. +.. CONTENTS + 1. Introduction + 1.1 purpose of memory hotplug + 1.2. Phases of memory hotplug + 1.3. Unit of Memory online/offline operation + 2. Kernel Configuration + 3. sysfs files for memory hotplug + 4. Physical memory hot-add phase + 4.1 Hardware(Firmware) Support + 4.2 Notify memory hot-add event by hand + 5. Logical Memory hot-add phase + 5.1. State of memory + 5.2. How to online memory + 6. Logical memory remove + 6.1 Memory offline and ZONE_MOVABLE + 6.2. How to offline memory + 7. Physical memory remove + 8. Memory hotplug event notifier + 9. Future Work List ---------------- -1. Introduction ---------------- -1.1 purpose of memory hotplug ------------- +.. note:: + + (1) x86_64's has special implementation for memory hotplug. + This text does not describe it. + (2) This text assumes that sysfs is mounted at /sys. + + +Introduction +============ + +purpose of memory hotplug +------------------------- + Memory Hotplug allows users to increase/decrease the amount of memory. Generally, there are two purposes. @@ -53,9 +58,11 @@ hardware which supports memory power management. Linux memory hotplug is designed for both purpose. -1.2. Phases of memory hotplug ---------------- -There are 2 phases in Memory Hotplug. +Phases of memory hotplug +------------------------ + +There are 2 phases in Memory Hotplug: + 1) Physical Memory Hotplug phase 2) Logical Memory Hotplug phase. @@ -70,7 +77,7 @@ management tables, and makes sysfs files for new memory's operation. If firmware supports notification of connection of new memory to OS, this phase is triggered automatically. ACPI can notify this event. If not, "probe" operation by system administration is used instead. -(see Section 4.). +(see :ref:`memory_hotplug_physical_mem`). Logical Memory Hotplug phase is to change memory state into available/unavailable for users. Amount of memory from user's view is @@ -83,11 +90,12 @@ Logical Memory Hotplug phase is triggered by write of sysfs file by system administrator. For the hot-add case, it must be executed after Physical Hotplug phase by hand. (However, if you writes udev's hotplug scripts for memory hotplug, these - phases can be execute in seamless way.) +phases can be execute in seamless way.) -1.3. Unit of Memory online/offline operation ------------- +Unit of Memory online/offline operation +--------------------------------------- + Memory hotplug uses SPARSEMEM memory model which allows memory to be divided into chunks of the same size. These chunks are called "sections". The size of a memory section is architecture dependent. For example, power uses 16MiB, ia64 @@ -97,46 +105,50 @@ Memory sections are combined into chunks referred to as "memory blocks". The size of a memory block is architecture dependent and represents the logical unit upon which memory online/offline operations are to be performed. The default size of a memory block is the same as memory section size unless an -architecture specifies otherwise. (see Section 3.) +architecture specifies otherwise. (see :ref:`memory_hotplug_sysfs_files`.) To determine the size (in bytes) of a memory block please read this file: /sys/devices/system/memory/block_size_bytes ------------------------ -2. Kernel Configuration ------------------------ +Kernel Configuration +==================== + To use memory hotplug feature, kernel must be compiled with following config options. -- For all memory hotplug - Memory model -> Sparse Memory (CONFIG_SPARSEMEM) - Allow for memory hot-add (CONFIG_MEMORY_HOTPLUG) +- For all memory hotplug: + - Memory model -> Sparse Memory (CONFIG_SPARSEMEM) + - Allow for memory hot-add (CONFIG_MEMORY_HOTPLUG) -- To enable memory removal, the following are also necessary - Allow for memory hot remove (CONFIG_MEMORY_HOTREMOVE) - Page Migration (CONFIG_MIGRATION) +- To enable memory removal, the following are also necessary: + - Allow for memory hot remove (CONFIG_MEMORY_HOTREMOVE) + - Page Migration (CONFIG_MIGRATION) -- For ACPI memory hotplug, the following are also necessary - Memory hotplug (under ACPI Support menu) (CONFIG_ACPI_HOTPLUG_MEMORY) - This option can be kernel module. +- For ACPI memory hotplug, the following are also necessary: + - Memory hotplug (under ACPI Support menu) (CONFIG_ACPI_HOTPLUG_MEMORY) + - This option can be kernel module. - As a related configuration, if your box has a feature of NUMA-node hotplug via ACPI, then this option is necessary too. - ACPI0004,PNP0A05 and PNP0A06 Container Driver (under ACPI Support menu) - (CONFIG_ACPI_CONTAINER). - This option can be kernel module too. + - ACPI0004,PNP0A05 and PNP0A06 Container Driver (under ACPI Support menu) + (CONFIG_ACPI_CONTAINER). + + This option can be kernel module too. + + +.. _memory_hotplug_sysfs_files: + +sysfs files for memory hotplug +============================== --------------------------------- -3 sysfs files for memory hotplug --------------------------------- All memory blocks have their device information in sysfs. Each memory block -is described under /sys/devices/system/memory as +is described under /sys/devices/system/memory as: -/sys/devices/system/memory/memoryXXX -(XXX is the memory block id.) + /sys/devices/system/memory/memoryXXX + (XXX is the memory block id.) For the memory block covered by the sysfs directory. It is expected that all memory sections in this range are present and no memory holes exist in the @@ -145,43 +157,53 @@ the existence of one should not affect the hotplug capabilities of the memory block. For example, assume 1GiB memory block size. A device for a memory starting at -0x100000000 is /sys/device/system/memory/memory4 -(0x100000000 / 1Gib = 4) +0x100000000 is /sys/device/system/memory/memory4:: + + (0x100000000 / 1Gib = 4) + This device covers address range [0x100000000 ... 0x140000000) Under each memory block, you can see 5 files: -/sys/devices/system/memory/memoryXXX/phys_index -/sys/devices/system/memory/memoryXXX/phys_device -/sys/devices/system/memory/memoryXXX/state -/sys/devices/system/memory/memoryXXX/removable -/sys/devices/system/memory/memoryXXX/valid_zones +- /sys/devices/system/memory/memoryXXX/phys_index +- /sys/devices/system/memory/memoryXXX/phys_device +- /sys/devices/system/memory/memoryXXX/state +- /sys/devices/system/memory/memoryXXX/removable +- /sys/devices/system/memory/memoryXXX/valid_zones + +=================== ============================================================ +``phys_index`` read-only and contains memory block id, same as XXX. +``state`` read-write + + - at read: contains online/offline state of memory. + - at write: user can specify "online_kernel", -'phys_index' : read-only and contains memory block id, same as XXX. -'state' : read-write - at read: contains online/offline state of memory. - at write: user can specify "online_kernel", "online_movable", "online", "offline" command which will be performed on all sections in the block. -'phys_device' : read-only: designed to show the name of physical memory +``phys_device`` read-only: designed to show the name of physical memory device. This is not well implemented now. -'removable' : read-only: contains an integer value indicating +``removable`` read-only: contains an integer value indicating whether the memory block is removable or not removable. A value of 1 indicates that the memory block is removable and a value of 0 indicates that it is not removable. A memory block is removable only if every section in the block is removable. -'valid_zones' : read-only: designed to show which zones this memory block +``valid_zones`` read-only: designed to show which zones this memory block can be onlined to. - The first column shows it's default zone. + + The first column shows it`s default zone. + "memory6/valid_zones: Normal Movable" shows this memoryblock can be onlined to ZONE_NORMAL by default and to ZONE_MOVABLE by online_movable. + "memory7/valid_zones: Movable Normal" shows this memoryblock can be onlined to ZONE_MOVABLE by default and to ZONE_NORMAL by online_kernel. +=================== ============================================================ + +.. note:: -NOTE: These directories/files appear after physical memory hotplug phase. If CONFIG_NUMA is enabled the memoryXXX/ directories can also be accessed @@ -193,13 +215,14 @@ For example: A backlink will also be created: /sys/devices/system/memory/memory9/node0 -> ../../node/node0 +.. _memory_hotplug_physical_mem: --------------------------------- -4. Physical memory hot-add phase --------------------------------- +Physical memory hot-add phase +============================= + +Hardware(Firmware) Support +-------------------------- -4.1 Hardware(Firmware) Support ------------- On x86_64/ia64 platform, memory hotplug by ACPI is supported. In general, the firmware (ACPI) which supports memory hotplug defines @@ -209,7 +232,8 @@ script. This will be done automatically. But scripts for memory hotplug are not contained in generic udev package(now). You may have to write it by yourself or online/offline memory by hand. -Please see "How to online memory", "How to offline memory" in this text. +Please see :ref:`memory_hotplug_how_to_online_memory` and +:ref:`memory_hotplug_how_to_offline_memory`. If firmware supports NUMA-node hotplug, and defines an object _HID "ACPI0004", "PNP0A05", or "PNP0A06", notification is asserted to it, and ACPI handler @@ -217,8 +241,9 @@ calls hotplug code for all of objects which are defined in it. If memory device is found, memory hotplug code will be called. -4.2 Notify memory hot-add event by hand ------------- +Notify memory hot-add event by hand +----------------------------------- + On some architectures, the firmware may not notify the kernel of a memory hotplug event. Therefore, the memory "probe" interface is supported to explicitly notify the kernel. This interface depends on @@ -229,45 +254,48 @@ notification. Probe interface is located at /sys/devices/system/memory/probe -You can tell the physical address of new memory to the kernel by +You can tell the physical address of new memory to the kernel by:: -% echo start_address_of_new_memory > /sys/devices/system/memory/probe + % echo start_address_of_new_memory > /sys/devices/system/memory/probe Then, [start_address_of_new_memory, start_address_of_new_memory + memory_block_size] memory range is hot-added. In this case, hotplug script is not called (in current implementation). You'll have to online memory by -yourself. Please see "How to online memory" in this text. +yourself. Please see :ref:`memory_hotplug_how_to_online_memory`. + +Logical Memory hot-add phase +============================ ------------------------------- -5. Logical Memory hot-add phase ------------------------------- +State of memory +--------------- + +To see (online/offline) state of a memory block, read 'state' file:: + + % cat /sys/device/system/memory/memoryXXX/state -5.1. State of memory ------------- -To see (online/offline) state of a memory block, read 'state' file. -% cat /sys/device/system/memory/memoryXXX/state +- If the memory block is online, you'll read "online". +- If the memory block is offline, you'll read "offline". -If the memory block is online, you'll read "online". -If the memory block is offline, you'll read "offline". +.. _memory_hotplug_how_to_online_memory: +How to online memory +-------------------- -5.2. How to online memory ------------- When the memory is hot-added, the kernel decides whether or not to "online" -it according to the policy which can be read from "auto_online_blocks" file: +it according to the policy which can be read from "auto_online_blocks" file:: -% cat /sys/devices/system/memory/auto_online_blocks + % cat /sys/devices/system/memory/auto_online_blocks The default depends on the CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE kernel config option. If it is disabled the default is "offline" which means the newly added memory is not in a ready-to-use state and you have to "online" the newly added memory blocks manually. Automatic onlining can be requested by writing "online" -to "auto_online_blocks" file: +to "auto_online_blocks" file:: -% echo online > /sys/devices/system/memory/auto_online_blocks + % echo online > /sys/devices/system/memory/auto_online_blocks This sets a global policy and impacts all memory blocks that will subsequently be hotplugged. Currently offline blocks keep their state. It is possible, under @@ -277,35 +305,43 @@ online. User space tools can check their "state" files If the automatic onlining wasn't requested, failed, or some memory block was offlined it is possible to change the individual block's state by writing to the -"state" file: +"state" file:: -% echo online > /sys/devices/system/memory/memoryXXX/state + % echo online > /sys/devices/system/memory/memoryXXX/state This onlining will not change the ZONE type of the target memory block, -If the memory block is in ZONE_NORMAL, you can change it to ZONE_MOVABLE: +If the memory block doesn't belong to any zone an appropriate kernel zone +(usually ZONE_NORMAL) will be used unless movable_node kernel command line +option is specified when ZONE_MOVABLE will be used. + +You can explicitly request to associate it with ZONE_MOVABLE by:: + + % echo online_movable > /sys/devices/system/memory/memoryXXX/state + +.. note:: current limit: this memory block must be adjacent to ZONE_MOVABLE -% echo online_movable > /sys/devices/system/memory/memoryXXX/state -(NOTE: current limit: this memory block must be adjacent to ZONE_MOVABLE) +Or you can explicitly request a kernel zone (usually ZONE_NORMAL) by:: -And if the memory block is in ZONE_MOVABLE, you can change it to ZONE_NORMAL: + % echo online_kernel > /sys/devices/system/memory/memoryXXX/state -% echo online_kernel > /sys/devices/system/memory/memoryXXX/state -(NOTE: current limit: this memory block must be adjacent to ZONE_NORMAL) +.. note:: current limit: this memory block must be adjacent to ZONE_NORMAL + +An explicit zone onlining can fail (e.g. when the range is already within +and existing and incompatible zone already). After this, memory block XXX's state will be 'online' and the amount of available memory will be increased. -Currently, newly added memory is added as ZONE_NORMAL (for powerpc, ZONE_DMA). This may be changed in future. ------------------------- -6. Logical memory remove ------------------------- +Logical memory remove +===================== + +Memory offline and ZONE_MOVABLE +------------------------------- -6.1 Memory offline and ZONE_MOVABLE ------------- Memory offlining is more complicated than memory online. Because memory offline has to make the whole memory block be unused, memory offline can fail if the memory block includes memory which cannot be freed. @@ -330,24 +366,27 @@ Assume the system has "TOTAL" amount of memory at boot time, this boot option creates ZONE_MOVABLE as following. 1) When kernelcore=YYYY boot option is used, - Size of memory not for movable pages (not for offline) is YYYY. - Size of memory for movable pages (for offline) is TOTAL-YYYY. + Size of memory not for movable pages (not for offline) is YYYY. + Size of memory for movable pages (for offline) is TOTAL-YYYY. 2) When movablecore=ZZZZ boot option is used, - Size of memory not for movable pages (not for offline) is TOTAL - ZZZZ. - Size of memory for movable pages (for offline) is ZZZZ. + Size of memory not for movable pages (not for offline) is TOTAL - ZZZZ. + Size of memory for movable pages (for offline) is ZZZZ. + +.. note:: + Unfortunately, there is no information to show which memory block belongs + to ZONE_MOVABLE. This is TBD. -Note: Unfortunately, there is no information to show which memory block belongs -to ZONE_MOVABLE. This is TBD. +.. _memory_hotplug_how_to_offline_memory: +How to offline memory +--------------------- -6.2. How to offline memory ------------- You can offline a memory block by using the same sysfs interface that was used -in memory onlining. +in memory onlining:: -% echo offline > /sys/devices/system/memory/memoryXXX/state + % echo offline > /sys/devices/system/memory/memoryXXX/state If offline succeeds, the state of the memory block is changed to be "offline". If it fails, some error core (like -EBUSY) will be returned by the kernel. @@ -361,22 +400,22 @@ able to offline it (or not). (For example, a page is referred to by some kernel internal call and released soon.) Consideration: -Memory hotplug's design direction is to make the possibility of memory offlining -higher and to guarantee unplugging memory under any situation. But it needs -more work. Returning -EBUSY under some situation may be good because the user -can decide to retry more or not by himself. Currently, memory offlining code -does some amount of retry with 120 seconds timeout. + Memory hotplug's design direction is to make the possibility of memory + offlining higher and to guarantee unplugging memory under any situation. But + it needs more work. Returning -EBUSY under some situation may be good because + the user can decide to retry more or not by himself. Currently, memory + offlining code does some amount of retry with 120 seconds timeout. + +Physical memory remove +====================== -------------------------- -7. Physical memory remove -------------------------- Need more implementation yet.... - Notification completion of remove works by OS to firmware. - Guard from remove if not yet. --------------------------------- -8. Memory hotplug event notifier --------------------------------- +Memory hotplug event notifier +============================= + Hotplugging events are sent to a notification queue. There are six types of notification defined in include/linux/memory.h: @@ -406,14 +445,14 @@ MEM_CANCEL_OFFLINE MEM_OFFLINE Generated after offlining memory is complete. -A callback routine can be registered by calling +A callback routine can be registered by calling:: hotplug_memory_notifier(callback_func, priority) Callback functions with higher values of priority are called before callback functions with lower values. -A callback function must have the following prototype: +A callback function must have the following prototype:: int callback_func( struct notifier_block *self, unsigned long action, void *arg); @@ -421,27 +460,28 @@ A callback function must have the following prototype: The first argument of the callback function (self) is a pointer to the block of the notifier chain that points to the callback function itself. The second argument (action) is one of the event types described above. -The third argument (arg) passes a pointer of struct memory_notify. - -struct memory_notify { - unsigned long start_pfn; - unsigned long nr_pages; - int status_change_nid_normal; - int status_change_nid_high; - int status_change_nid; -} - -start_pfn is start_pfn of online/offline memory. -nr_pages is # of pages of online/offline memory. -status_change_nid_normal is set node id when N_NORMAL_MEMORY of nodemask -is (will be) set/clear, if this is -1, then nodemask status is not changed. -status_change_nid_high is set node id when N_HIGH_MEMORY of nodemask -is (will be) set/clear, if this is -1, then nodemask status is not changed. -status_change_nid is set node id when N_MEMORY of nodemask is (will be) -set/clear. It means a new(memoryless) node gets new memory by online and a -node loses all memory. If this is -1, then nodemask status is not changed. -If status_changed_nid* >= 0, callback should create/discard structures for the -node if necessary. +The third argument (arg) passes a pointer of struct memory_notify:: + + struct memory_notify { + unsigned long start_pfn; + unsigned long nr_pages; + int status_change_nid_normal; + int status_change_nid_high; + int status_change_nid; + } + +- start_pfn is start_pfn of online/offline memory. +- nr_pages is # of pages of online/offline memory. +- status_change_nid_normal is set node id when N_NORMAL_MEMORY of nodemask + is (will be) set/clear, if this is -1, then nodemask status is not changed. +- status_change_nid_high is set node id when N_HIGH_MEMORY of nodemask + is (will be) set/clear, if this is -1, then nodemask status is not changed. +- status_change_nid is set node id when N_MEMORY of nodemask is (will be) + set/clear. It means a new(memoryless) node gets new memory by online and a + node loses all memory. If this is -1, then nodemask status is not changed. + + If status_changed_nid* >= 0, callback should create/discard structures for the + node if necessary. The callback routine shall return one of the values NOTIFY_DONE, NOTIFY_OK, NOTIFY_BAD, NOTIFY_STOP @@ -455,9 +495,9 @@ further processing of the notification queue. NOTIFY_STOP stops further processing of the notification queue. --------------- -9. Future Work --------------- +Future Work +=========== + - allowing memory hot-add to ZONE_MOVABLE. maybe we need some switch like sysctl or new control file. - showing memory block and physical device relationship. @@ -465,4 +505,3 @@ NOTIFY_STOP stops further processing of the notification queue. - support HugeTLB page migration and offlining. - memmap removing at memory offline. - physical remove memory. - diff --git a/Documentation/men-chameleon-bus.txt b/Documentation/men-chameleon-bus.txt index 30ded732027e..1b1f048aa748 100644 --- a/Documentation/men-chameleon-bus.txt +++ b/Documentation/men-chameleon-bus.txt @@ -1,163 +1,175 @@ - MEN Chameleon Bus - ================= - -Table of Contents ================= -1 Introduction - 1.1 Scope of this Document - 1.2 Limitations of the current implementation -2 Architecture - 2.1 MEN Chameleon Bus - 2.2 Carrier Devices - 2.3 Parser -3 Resource handling - 3.1 Memory Resources - 3.2 IRQs -4 Writing an MCB driver - 4.1 The driver structure - 4.2 Probing and attaching - 4.3 Initializing the driver - - -1 Introduction -=============== - This document describes the architecture and implementation of the MEN - Chameleon Bus (called MCB throughout this document). - -1.1 Scope of this Document ---------------------------- - This document is intended to be a short overview of the current - implementation and does by no means describe the complete possibilities of MCB - based devices. - -1.2 Limitations of the current implementation ----------------------------------------------- - The current implementation is limited to PCI and PCIe based carrier devices - that only use a single memory resource and share the PCI legacy IRQ. Not - implemented are: - - Multi-resource MCB devices like the VME Controller or M-Module carrier. - - MCB devices that need another MCB device, like SRAM for a DMA Controller's - buffer descriptors or a video controller's video memory. - - A per-carrier IRQ domain for carrier devices that have one (or more) IRQs - per MCB device like PCIe based carriers with MSI or MSI-X support. - -2 Architecture -=============== - MCB is divided into 3 functional blocks: - - The MEN Chameleon Bus itself, - - drivers for MCB Carrier Devices and - - the parser for the Chameleon table. - -2.1 MEN Chameleon Bus +MEN Chameleon Bus +================= + +.. Table of Contents + ================= + 1 Introduction + 1.1 Scope of this Document + 1.2 Limitations of the current implementation + 2 Architecture + 2.1 MEN Chameleon Bus + 2.2 Carrier Devices + 2.3 Parser + 3 Resource handling + 3.1 Memory Resources + 3.2 IRQs + 4 Writing an MCB driver + 4.1 The driver structure + 4.2 Probing and attaching + 4.3 Initializing the driver + + +Introduction +============ + +This document describes the architecture and implementation of the MEN +Chameleon Bus (called MCB throughout this document). + +Scope of this Document ---------------------- - The MEN Chameleon Bus is an artificial bus system that attaches to a so - called Chameleon FPGA device found on some hardware produced my MEN Mikro - Elektronik GmbH. These devices are multi-function devices implemented in a - single FPGA and usually attached via some sort of PCI or PCIe link. Each - FPGA contains a header section describing the content of the FPGA. The - header lists the device id, PCI BAR, offset from the beginning of the PCI - BAR, size in the FPGA, interrupt number and some other properties currently - not handled by the MCB implementation. - -2.2 Carrier Devices + +This document is intended to be a short overview of the current +implementation and does by no means describe the complete possibilities of MCB +based devices. + +Limitations of the current implementation +----------------------------------------- + +The current implementation is limited to PCI and PCIe based carrier devices +that only use a single memory resource and share the PCI legacy IRQ. Not +implemented are: + +- Multi-resource MCB devices like the VME Controller or M-Module carrier. +- MCB devices that need another MCB device, like SRAM for a DMA Controller's + buffer descriptors or a video controller's video memory. +- A per-carrier IRQ domain for carrier devices that have one (or more) IRQs + per MCB device like PCIe based carriers with MSI or MSI-X support. + +Architecture +============ + +MCB is divided into 3 functional blocks: + +- The MEN Chameleon Bus itself, +- drivers for MCB Carrier Devices and +- the parser for the Chameleon table. + +MEN Chameleon Bus +----------------- + +The MEN Chameleon Bus is an artificial bus system that attaches to a so +called Chameleon FPGA device found on some hardware produced my MEN Mikro +Elektronik GmbH. These devices are multi-function devices implemented in a +single FPGA and usually attached via some sort of PCI or PCIe link. Each +FPGA contains a header section describing the content of the FPGA. The +header lists the device id, PCI BAR, offset from the beginning of the PCI +BAR, size in the FPGA, interrupt number and some other properties currently +not handled by the MCB implementation. + +Carrier Devices +--------------- + +A carrier device is just an abstraction for the real world physical bus the +Chameleon FPGA is attached to. Some IP Core drivers may need to interact with +properties of the carrier device (like querying the IRQ number of a PCI +device). To provide abstraction from the real hardware bus, an MCB carrier +device provides callback methods to translate the driver's MCB function calls +to hardware related function calls. For example a carrier device may +implement the get_irq() method which can be translated into a hardware bus +query for the IRQ number the device should use. + +Parser +------ + +The parser reads the first 512 bytes of a Chameleon device and parses the +Chameleon table. Currently the parser only supports the Chameleon v2 variant +of the Chameleon table but can easily be adopted to support an older or +possible future variant. While parsing the table's entries new MCB devices +are allocated and their resources are assigned according to the resource +assignment in the Chameleon table. After resource assignment is finished, the +MCB devices are registered at the MCB and thus at the driver core of the +Linux kernel. + +Resource handling +================= + +The current implementation assigns exactly one memory and one IRQ resource +per MCB device. But this is likely going to change in the future. + +Memory Resources +---------------- + +Each MCB device has exactly one memory resource, which can be requested from +the MCB bus. This memory resource is the physical address of the MCB device +inside the carrier and is intended to be passed to ioremap() and friends. It +is already requested from the kernel by calling request_mem_region(). + +IRQs +---- + +Each MCB device has exactly one IRQ resource, which can be requested from the +MCB bus. If a carrier device driver implements the ->get_irq() callback +method, the IRQ number assigned by the carrier device will be returned, +otherwise the IRQ number inside the Chameleon table will be returned. This +number is suitable to be passed to request_irq(). + +Writing an MCB driver +===================== + +The driver structure -------------------- - A carrier device is just an abstraction for the real world physical bus the - Chameleon FPGA is attached to. Some IP Core drivers may need to interact with - properties of the carrier device (like querying the IRQ number of a PCI - device). To provide abstraction from the real hardware bus, an MCB carrier - device provides callback methods to translate the driver's MCB function calls - to hardware related function calls. For example a carrier device may - implement the get_irq() method which can be translated into a hardware bus - query for the IRQ number the device should use. - -2.3 Parser ------------ - The parser reads the first 512 bytes of a Chameleon device and parses the - Chameleon table. Currently the parser only supports the Chameleon v2 variant - of the Chameleon table but can easily be adopted to support an older or - possible future variant. While parsing the table's entries new MCB devices - are allocated and their resources are assigned according to the resource - assignment in the Chameleon table. After resource assignment is finished, the - MCB devices are registered at the MCB and thus at the driver core of the - Linux kernel. - -3 Resource handling -==================== - The current implementation assigns exactly one memory and one IRQ resource - per MCB device. But this is likely going to change in the future. - -3.1 Memory Resources + +Each MCB driver has a structure to identify the device driver as well as +device ids which identify the IP Core inside the FPGA. The driver structure +also contains callback methods which get executed on driver probe and +removal from the system:: + + static const struct mcb_device_id foo_ids[] = { + { .device = 0x123 }, + { } + }; + MODULE_DEVICE_TABLE(mcb, foo_ids); + + static struct mcb_driver foo_driver = { + driver = { + .name = "foo-bar", + .owner = THIS_MODULE, + }, + .probe = foo_probe, + .remove = foo_remove, + .id_table = foo_ids, + }; + +Probing and attaching --------------------- - Each MCB device has exactly one memory resource, which can be requested from - the MCB bus. This memory resource is the physical address of the MCB device - inside the carrier and is intended to be passed to ioremap() and friends. It - is already requested from the kernel by calling request_mem_region(). - -3.2 IRQs ---------- - Each MCB device has exactly one IRQ resource, which can be requested from the - MCB bus. If a carrier device driver implements the ->get_irq() callback - method, the IRQ number assigned by the carrier device will be returned, - otherwise the IRQ number inside the Chameleon table will be returned. This - number is suitable to be passed to request_irq(). - -4 Writing an MCB driver -======================= - -4.1 The driver structure -------------------------- - Each MCB driver has a structure to identify the device driver as well as - device ids which identify the IP Core inside the FPGA. The driver structure - also contains callback methods which get executed on driver probe and - removal from the system. - - - static const struct mcb_device_id foo_ids[] = { - { .device = 0x123 }, - { } - }; - MODULE_DEVICE_TABLE(mcb, foo_ids); - - static struct mcb_driver foo_driver = { - driver = { - .name = "foo-bar", - .owner = THIS_MODULE, - }, - .probe = foo_probe, - .remove = foo_remove, - .id_table = foo_ids, - }; - -4.2 Probing and attaching --------------------------- - When a driver is loaded and the MCB devices it services are found, the MCB - core will call the driver's probe callback method. When the driver is removed - from the system, the MCB core will call the driver's remove callback method. - - - static init foo_probe(struct mcb_device *mdev, const struct mcb_device_id *id); - static void foo_remove(struct mcb_device *mdev); - -4.3 Initializing the driver ----------------------------- - When the kernel is booted or your foo driver module is inserted, you have to - perform driver initialization. Usually it is enough to register your driver - module at the MCB core. - - - static int __init foo_init(void) - { - return mcb_register_driver(&foo_driver); - } - module_init(foo_init); - - static void __exit foo_exit(void) - { - mcb_unregister_driver(&foo_driver); - } - module_exit(foo_exit); - - The module_mcb_driver() macro can be used to reduce the above code. - - - module_mcb_driver(foo_driver); + +When a driver is loaded and the MCB devices it services are found, the MCB +core will call the driver's probe callback method. When the driver is removed +from the system, the MCB core will call the driver's remove callback method:: + + static init foo_probe(struct mcb_device *mdev, const struct mcb_device_id *id); + static void foo_remove(struct mcb_device *mdev); + +Initializing the driver +----------------------- + +When the kernel is booted or your foo driver module is inserted, you have to +perform driver initialization. Usually it is enough to register your driver +module at the MCB core:: + + static int __init foo_init(void) + { + return mcb_register_driver(&foo_driver); + } + module_init(foo_init); + + static void __exit foo_exit(void) + { + mcb_unregister_driver(&foo_driver); + } + module_exit(foo_exit); + +The module_mcb_driver() macro can be used to reduce the above code:: + + module_mcb_driver(foo_driver); diff --git a/Documentation/networking/timestamping.txt b/Documentation/networking/timestamping.txt index 196ba17cc344..1be0b6f9e0cb 100644 --- a/Documentation/networking/timestamping.txt +++ b/Documentation/networking/timestamping.txt @@ -44,8 +44,7 @@ timeval of SO_TIMESTAMP (ms). Supports multiple types of timestamp requests. As a result, this socket option takes a bitmap of flags, not a boolean. In - err = setsockopt(fd, SOL_SOCKET, SO_TIMESTAMPING, (void *) val, - sizeof(val)); + err = setsockopt(fd, SOL_SOCKET, SO_TIMESTAMPING, &val, sizeof(val)); val is an integer with any of the following bits set. Setting other bit returns EINVAL and does not change the current state. @@ -249,8 +248,7 @@ setsockopt to receive timestamps: __u32 val = SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID /* or any other flag */; - err = setsockopt(fd, SOL_SOCKET, SO_TIMESTAMPING, (void *) val, - sizeof(val)); + err = setsockopt(fd, SOL_SOCKET, SO_TIMESTAMPING, &val, sizeof(val)); 1.4 Bytestream Timestamps diff --git a/Documentation/nommu-mmap.txt b/Documentation/nommu-mmap.txt index ae57b9ea0d41..69556f0d494b 100644 --- a/Documentation/nommu-mmap.txt +++ b/Documentation/nommu-mmap.txt @@ -1,6 +1,6 @@ - ============================= - NO-MMU MEMORY MAPPING SUPPORT - ============================= +============================= +No-MMU memory mapping support +============================= The kernel has limited support for memory mapping under no-MMU conditions, such as are used in uClinux environments. From the userspace point of view, memory @@ -16,7 +16,7 @@ the CLONE_VM flag. The behaviour is similar between the MMU and no-MMU cases, but not identical; and it's also much more restricted in the latter case: - (*) Anonymous mapping, MAP_PRIVATE + (#) Anonymous mapping, MAP_PRIVATE In the MMU case: VM regions backed by arbitrary pages; copy-on-write across fork. @@ -24,14 +24,14 @@ and it's also much more restricted in the latter case: In the no-MMU case: VM regions backed by arbitrary contiguous runs of pages. - (*) Anonymous mapping, MAP_SHARED + (#) Anonymous mapping, MAP_SHARED These behave very much like private mappings, except that they're shared across fork() or clone() without CLONE_VM in the MMU case. Since the no-MMU case doesn't support these, behaviour is identical to MAP_PRIVATE there. - (*) File, MAP_PRIVATE, PROT_READ / PROT_EXEC, !PROT_WRITE + (#) File, MAP_PRIVATE, PROT_READ / PROT_EXEC, !PROT_WRITE In the MMU case: VM regions backed by pages read from file; changes to the underlying file are reflected in the mapping; copied across fork. @@ -56,7 +56,7 @@ and it's also much more restricted in the latter case: are visible in other processes (no MMU protection), but should not happen. - (*) File, MAP_PRIVATE, PROT_READ / PROT_EXEC, PROT_WRITE + (#) File, MAP_PRIVATE, PROT_READ / PROT_EXEC, PROT_WRITE In the MMU case: like the non-PROT_WRITE case, except that the pages in question get copied before the write actually happens. From that point @@ -66,7 +66,7 @@ and it's also much more restricted in the latter case: In the no-MMU case: works much like the non-PROT_WRITE case, except that a copy is always taken and never shared. - (*) Regular file / blockdev, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE + (#) Regular file / blockdev, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE In the MMU case: VM regions backed by pages read from file; changes to pages written back to file; writes to file reflected into pages backing @@ -74,7 +74,7 @@ and it's also much more restricted in the latter case: In the no-MMU case: not supported. - (*) Memory backed regular file, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE + (#) Memory backed regular file, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE In the MMU case: As for ordinary regular files. @@ -85,7 +85,7 @@ and it's also much more restricted in the latter case: as for the MMU case. If the filesystem does not provide any such support, then the mapping request will be denied. - (*) Memory backed blockdev, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE + (#) Memory backed blockdev, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE In the MMU case: As for ordinary regular files. @@ -94,7 +94,7 @@ and it's also much more restricted in the latter case: truncate being called. The ramdisk driver could do this if it allocated all its memory as a contiguous array upfront. - (*) Memory backed chardev, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE + (#) Memory backed chardev, MAP_SHARED, PROT_READ / PROT_EXEC / PROT_WRITE In the MMU case: As for ordinary regular files. @@ -105,21 +105,20 @@ and it's also much more restricted in the latter case: provide any such support, then the mapping request will be denied. -============================ -FURTHER NOTES ON NO-MMU MMAP +Further notes on no-MMU MMAP ============================ - (*) A request for a private mapping of a file may return a buffer that is not + (#) A request for a private mapping of a file may return a buffer that is not page-aligned. This is because XIP may take place, and the data may not be paged aligned in the backing store. - (*) A request for an anonymous mapping will always be page aligned. If + (#) A request for an anonymous mapping will always be page aligned. If possible the size of the request should be a power of two otherwise some of the space may be wasted as the kernel must allocate a power-of-2 granule but will only discard the excess if appropriately configured as this has an effect on fragmentation. - (*) The memory allocated by a request for an anonymous mapping will normally + (#) The memory allocated by a request for an anonymous mapping will normally be cleared by the kernel before being returned in accordance with the Linux man pages (ver 2.22 or later). @@ -145,24 +144,23 @@ FURTHER NOTES ON NO-MMU MMAP uClibc uses this to speed up malloc(), and the ELF-FDPIC binfmt uses this to allocate the brk and stack region. - (*) A list of all the private copy and anonymous mappings on the system is + (#) A list of all the private copy and anonymous mappings on the system is visible through /proc/maps in no-MMU mode. - (*) A list of all the mappings in use by a process is visible through + (#) A list of all the mappings in use by a process is visible through /proc/<pid>/maps in no-MMU mode. - (*) Supplying MAP_FIXED or a requesting a particular mapping address will + (#) Supplying MAP_FIXED or a requesting a particular mapping address will result in an error. - (*) Files mapped privately usually have to have a read method provided by the + (#) Files mapped privately usually have to have a read method provided by the driver or filesystem so that the contents can be read into the memory allocated if mmap() chooses not to map the backing device directly. An error will result if they don't. This is most likely to be encountered with character device files, pipes, fifos and sockets. -========================== -INTERPROCESS SHARED MEMORY +Interprocess shared memory ========================== Both SYSV IPC SHM shared memory and POSIX shared memory is supported in NOMMU @@ -170,8 +168,7 @@ mode. The former through the usual mechanism, the latter through files created on ramfs or tmpfs mounts. -======= -FUTEXES +Futexes ======= Futexes are supported in NOMMU mode if the arch supports them. An error will @@ -180,12 +177,11 @@ mappings made by a process or if the mapping in which the address lies does not support futexes (such as an I/O chardev mapping). -============= -NO-MMU MREMAP +No-MMU mremap ============= The mremap() function is partially supported. It may change the size of a -mapping, and may move it[*] if MREMAP_MAYMOVE is specified and if the new size +mapping, and may move it [#]_ if MREMAP_MAYMOVE is specified and if the new size of the mapping exceeds the size of the slab object currently occupied by the memory to which the mapping refers, or if a smaller slab object could be used. @@ -200,11 +196,10 @@ a previously mapped object. It may not be used to create holes in existing mappings, move parts of existing mappings or resize parts of mappings. It must act on a complete mapping. -[*] Not currently supported. +.. [#] Not currently supported. -============================================ -PROVIDING SHAREABLE CHARACTER DEVICE SUPPORT +Providing shareable character device support ============================================ To provide shareable character device support, a driver must provide a @@ -235,7 +230,7 @@ direct the call to the device-specific driver. Under such circumstances, the mapping request will be rejected if NOMMU_MAP_COPY is not specified, and a copy mapped otherwise. -IMPORTANT NOTE: +.. important:: Some types of device may present a different appearance to anyone looking at them in certain modes. Flash chips can be like this; for @@ -249,8 +244,7 @@ IMPORTANT NOTE: circumstances! -============================================== -PROVIDING SHAREABLE MEMORY-BACKED FILE SUPPORT +Providing shareable memory-backed file support ============================================== Provision of shared mappings on memory backed files is similar to the provision @@ -267,8 +261,7 @@ Memory backed devices are indicated by the mapping's backing device info having the memory_backed flag set. -======================================== -PROVIDING SHAREABLE BLOCK DEVICE SUPPORT +Providing shareable block device support ======================================== Provision of shared mappings on block device files is exactly the same as for @@ -276,8 +269,7 @@ character devices. If there isn't a real device underneath, then the driver should allocate sufficient contiguous memory to honour any supported mapping. -================================= -ADJUSTING PAGE TRIMMING BEHAVIOUR +Adjusting page trimming behaviour ================================= NOMMU mmap automatically rounds up to the nearest power-of-2 number of pages @@ -288,4 +280,4 @@ allocator. In order to retain finer-grained control over fragmentation, this behaviour can either be disabled completely, or bumped up to a higher page watermark where trimming begins. -Page trimming behaviour is configurable via the sysctl `vm.nr_trim_pages'. +Page trimming behaviour is configurable via the sysctl ``vm.nr_trim_pages``. diff --git a/Documentation/ntb.txt b/Documentation/ntb.txt index 1d9bbabb6c79..a043854d28df 100644 --- a/Documentation/ntb.txt +++ b/Documentation/ntb.txt @@ -1,16 +1,21 @@ -# NTB Drivers +=========== +NTB Drivers +=========== NTB (Non-Transparent Bridge) is a type of PCI-Express bridge chip that connects -the separate memory systems of two computers to the same PCI-Express fabric. -Existing NTB hardware supports a common feature set, including scratchpad -registers, doorbell registers, and memory translation windows. Scratchpad -registers are read-and-writable registers that are accessible from either side -of the device, so that peers can exchange a small amount of information at a -fixed address. Doorbell registers provide a way for peers to send interrupt -events. Memory windows allow translated read and write access to the peer -memory. - -## NTB Core Driver (ntb) +the separate memory systems of two or more computers to the same PCI-Express +fabric. Existing NTB hardware supports a common feature set: doorbell +registers and memory translation windows, as well as non common features like +scratchpad and message registers. Scratchpad registers are read-and-writable +registers that are accessible from either side of the device, so that peers can +exchange a small amount of information at a fixed address. Message registers can +be utilized for the same purpose. Additionally they are provided with with +special status bits to make sure the information isn't rewritten by another +peer. Doorbell registers provide a way for peers to send interrupt events. +Memory windows allow translated read and write access to the peer memory. + +NTB Core Driver (ntb) +===================== The NTB core driver defines an api wrapping the common feature set, and allows clients interested in NTB features to discover NTB the devices supported by @@ -18,7 +23,8 @@ hardware drivers. The term "client" is used here to mean an upper layer component making use of the NTB api. The term "driver," or "hardware driver," is used here to mean a driver for a specific vendor and model of NTB hardware. -## NTB Client Drivers +NTB Client Drivers +================== NTB client drivers should register with the NTB core driver. After registering, the client probe and remove functions will be called appropriately @@ -26,7 +32,90 @@ as ntb hardware, or hardware drivers, are inserted and removed. The registration uses the Linux Device framework, so it should feel familiar to anyone who has written a pci driver. -### NTB Transport Client (ntb\_transport) and NTB Netdev (ntb\_netdev) +NTB Typical client driver implementation +---------------------------------------- + +Primary purpose of NTB is to share some peace of memory between at least two +systems. So the NTB device features like Scratchpad/Message registers are +mainly used to perform the proper memory window initialization. Typically +there are two types of memory window interfaces supported by the NTB API: +inbound translation configured on the local ntb port and outbound translation +configured by the peer, on the peer ntb port. The first type is +depicted on the next figure + +Inbound translation: + Memory: Local NTB Port: Peer NTB Port: Peer MMIO: + ____________ + | dma-mapped |-ntb_mw_set_trans(addr) | + | memory | _v____________ | ______________ + | (addr) |<======| MW xlat addr |<====| MW base addr |<== memory-mapped IO + |------------| |--------------| | |--------------| + +So typical scenario of the first type memory window initialization looks: +1) allocate a memory region, 2) put translated address to NTB config, +3) somehow notify a peer device of performed initialization, 4) peer device +maps corresponding outbound memory window so to have access to the shared +memory region. + +The second type of interface, that implies the shared windows being +initialized by a peer device, is depicted on the figure: + +Outbound translation: + Memory: Local NTB Port: Peer NTB Port: Peer MMIO: + ____________ ______________ + | dma-mapped | | | MW base addr |<== memory-mapped IO + | memory | | |--------------| + | (addr) |<===================| MW xlat addr |<-ntb_peer_mw_set_trans(addr) + |------------| | |--------------| + +Typical scenario of the second type interface initialization would be: +1) allocate a memory region, 2) somehow deliver a translated address to a peer +device, 3) peer puts the translated address to NTB config, 4) peer device maps +outbound memory window so to have access to the shared memory region. + +As one can see the described scenarios can be combined in one portable +algorithm. + Local device: + 1) Allocate memory for a shared window + 2) Initialize memory window by translated address of the allocated region + (it may fail if local memory window initialization is unsupported) + 3) Send the translated address and memory window index to a peer device + Peer device: + 1) Initialize memory window with retrieved address of the allocated + by another device memory region (it may fail if peer memory window + initialization is unsupported) + 2) Map outbound memory window + +In accordance with this scenario, the NTB Memory Window API can be used as +follows: + Local device: + 1) ntb_mw_count(pidx) - retrieve number of memory ranges, which can + be allocated for memory windows between local device and peer device + of port with specified index. + 2) ntb_get_align(pidx, midx) - retrieve parameters restricting the + shared memory region alignment and size. Then memory can be properly + allocated. + 3) Allocate physically contiguous memory region in compliance with + restrictions retrieved in 2). + 4) ntb_mw_set_trans(pidx, midx) - try to set translation address of + the memory window with specified index for the defined peer device + (it may fail if local translated address setting is not supported) + 5) Send translated base address (usually together with memory window + number) to the peer device using, for instance, scratchpad or message + registers. + Peer device: + 1) ntb_peer_mw_set_trans(pidx, midx) - try to set received from other + device (related to pidx) translated address for specified memory + window. It may fail if retrieved address, for instance, exceeds + maximum possible address or isn't properly aligned. + 2) ntb_peer_mw_get_addr(widx) - retrieve MMIO address to map the memory + window so to have an access to the shared memory. + +Also it is worth to note, that method ntb_mw_count(pidx) should return the +same value as ntb_peer_mw_count() on the peer with port index - pidx. + +NTB Transport Client (ntb\_transport) and NTB Netdev (ntb\_netdev) +------------------------------------------------------------------ The primary client for NTB is the Transport client, used in tandem with NTB Netdev. These drivers function together to create a logical link to the peer, @@ -37,7 +126,8 @@ Transport queue pair. Network data is copied between socket buffers and the Transport queue pair buffer. The Transport client may be used for other things besides Netdev, however no other applications have yet been written. -### NTB Ping Pong Test Client (ntb\_pingpong) +NTB Ping Pong Test Client (ntb\_pingpong) +----------------------------------------- The Ping Pong test client serves as a demonstration to exercise the doorbell and scratchpad registers of NTB hardware, and as an example simple NTB client. @@ -64,7 +154,8 @@ Module Parameters: * dyndbg - It is suggested to specify dyndbg=+p when loading this module, and then to observe debugging output on the console. -### NTB Tool Test Client (ntb\_tool) +NTB Tool Test Client (ntb\_tool) +-------------------------------- The Tool test client serves for debugging, primarily, ntb hardware and drivers. The Tool provides access through debugfs for reading, setting, and clearing the @@ -74,48 +165,60 @@ The Tool does not currently have any module parameters. Debugfs Files: -* *debugfs*/ntb\_tool/*hw*/ - A directory in debugfs will be created for each +* *debugfs*/ntb\_tool/*hw*/ + A directory in debugfs will be created for each NTB device probed by the tool. This directory is shortened to *hw* below. -* *hw*/db - This file is used to read, set, and clear the local doorbell. Not +* *hw*/db + This file is used to read, set, and clear the local doorbell. Not all operations may be supported by all hardware. To read the doorbell, read the file. To set the doorbell, write `s` followed by the bits to set (eg: `echo 's 0x0101' > db`). To clear the doorbell, write `c` followed by the bits to clear. -* *hw*/mask - This file is used to read, set, and clear the local doorbell mask. +* *hw*/mask + This file is used to read, set, and clear the local doorbell mask. See *db* for details. -* *hw*/peer\_db - This file is used to read, set, and clear the peer doorbell. +* *hw*/peer\_db + This file is used to read, set, and clear the peer doorbell. See *db* for details. -* *hw*/peer\_mask - This file is used to read, set, and clear the peer doorbell +* *hw*/peer\_mask + This file is used to read, set, and clear the peer doorbell mask. See *db* for details. -* *hw*/spad - This file is used to read and write local scratchpads. To read +* *hw*/spad + This file is used to read and write local scratchpads. To read the values of all scratchpads, read the file. To write values, write a series of pairs of scratchpad number and value (eg: `echo '4 0x123 7 0xabc' > spad` # to set scratchpads `4` and `7` to `0x123` and `0xabc`, respectively). -* *hw*/peer\_spad - This file is used to read and write peer scratchpads. See +* *hw*/peer\_spad + This file is used to read and write peer scratchpads. See *spad* for details. -## NTB Hardware Drivers +NTB Hardware Drivers +==================== NTB hardware drivers should register devices with the NTB core driver. After registering, clients probe and remove functions will be called. -### NTB Intel Hardware Driver (ntb\_hw\_intel) +NTB Intel Hardware Driver (ntb\_hw\_intel) +------------------------------------------ The Intel hardware driver supports NTB on Xeon and Atom CPUs. Module Parameters: -* b2b\_mw\_idx - If the peer ntb is to be accessed via a memory window, then use +* b2b\_mw\_idx + If the peer ntb is to be accessed via a memory window, then use this memory window to access the peer ntb. A value of zero or positive starts from the first mw idx, and a negative value starts from the last mw idx. Both sides MUST set the same value here! The default value is `-1`. -* b2b\_mw\_share - If the peer ntb is to be accessed via a memory window, and if +* b2b\_mw\_share + If the peer ntb is to be accessed via a memory window, and if the memory window is large enough, still allow the client to use the second half of the memory window for address translation to the peer. -* xeon\_b2b\_usd\_bar2\_addr64 - If using B2B topology on Xeon hardware, use +* xeon\_b2b\_usd\_bar2\_addr64 + If using B2B topology on Xeon hardware, use this 64 bit address on the bus between the NTB devices for the window at BAR2, on the upstream side of the link. * xeon\_b2b\_usd\_bar4\_addr64 - See *xeon\_b2b\_bar2\_addr64*. diff --git a/Documentation/numastat.txt b/Documentation/numastat.txt index 520327790d54..aaf1667489f8 100644 --- a/Documentation/numastat.txt +++ b/Documentation/numastat.txt @@ -1,10 +1,12 @@ - +=============================== Numa policy hit/miss statistics +=============================== /sys/devices/system/node/node*/numastat All units are pages. Hugepages have separate counters. +=============== ============================================================ numa_hit A process wanted to allocate memory from this node, and succeeded. @@ -20,6 +22,7 @@ other_node A process ran on this node and got memory from another node. interleave_hit Interleaving wanted to allocate from this node and succeeded. +=============== ============================================================ For easier reading you can use the numastat utility from the numactl package (http://oss.sgi.com/projects/libnuma/). Note that it only works diff --git a/Documentation/padata.txt b/Documentation/padata.txt index 7ddfe216a0aa..b103d0c82000 100644 --- a/Documentation/padata.txt +++ b/Documentation/padata.txt @@ -1,5 +1,8 @@ +======================================= The padata parallel execution mechanism -Last updated for 2.6.36 +======================================= + +:Last updated: for 2.6.36 Padata is a mechanism by which the kernel can farm work out to be done in parallel on multiple CPUs while retaining the ordering of tasks. It was @@ -9,7 +12,7 @@ those packets. The crypto developers made a point of writing padata in a sufficiently general fashion that it could be put to other uses as well. The first step in using padata is to set up a padata_instance structure for -overall control of how tasks are to be run: +overall control of how tasks are to be run:: #include <linux/padata.h> @@ -24,7 +27,7 @@ The workqueue wq is where the work will actually be done; it should be a multithreaded queue, naturally. To allocate a padata instance with the cpu_possible_mask for both -cpumasks this helper function can be used: +cpumasks this helper function can be used:: struct padata_instance *padata_alloc_possible(struct workqueue_struct *wq); @@ -36,7 +39,7 @@ it is legal to supply a cpumask to padata that contains offline CPUs. Once an offline CPU in the user supplied cpumask comes online, padata is going to use it. -There are functions for enabling and disabling the instance: +There are functions for enabling and disabling the instance:: int padata_start(struct padata_instance *pinst); void padata_stop(struct padata_instance *pinst); @@ -48,7 +51,7 @@ padata cpumask contains no active CPU (flag not set). padata_stop clears the flag and blocks until the padata instance is unused. -The list of CPUs to be used can be adjusted with these functions: +The list of CPUs to be used can be adjusted with these functions:: int padata_set_cpumasks(struct padata_instance *pinst, cpumask_var_t pcpumask, @@ -71,12 +74,12 @@ padata_add_cpu/padata_remove_cpu are used. cpu specifies the CPU to add or remove and mask is one of PADATA_CPU_SERIAL, PADATA_CPU_PARALLEL. If a user is interested in padata cpumask changes, he can register to -the padata cpumask change notifier: +the padata cpumask change notifier:: int padata_register_cpumask_notifier(struct padata_instance *pinst, struct notifier_block *nblock); -To unregister from that notifier: +To unregister from that notifier:: int padata_unregister_cpumask_notifier(struct padata_instance *pinst, struct notifier_block *nblock); @@ -84,7 +87,7 @@ To unregister from that notifier: The padata cpumask change notifier notifies about changes of the usable cpumasks, i.e. the subset of active CPUs in the user supplied cpumask. -Padata calls the notifier chain with: +Padata calls the notifier chain with:: blocking_notifier_call_chain(&pinst->cpumask_change_notifier, notification_mask, @@ -95,7 +98,7 @@ is one of PADATA_CPU_SERIAL, PADATA_CPU_PARALLEL and cpumask is a pointer to a struct padata_cpumask that contains the new cpumask information. Actually submitting work to the padata instance requires the creation of a -padata_priv structure: +padata_priv structure:: struct padata_priv { /* Other stuff here... */ @@ -110,7 +113,7 @@ parallel() and serial() functions should be provided. Those functions will be called in the process of getting the work done as we will see momentarily. -The submission of work is done with: +The submission of work is done with:: int padata_do_parallel(struct padata_instance *pinst, struct padata_priv *padata, int cb_cpu); @@ -138,7 +141,7 @@ need not be completed during this call, but, if parallel() leaves work outstanding, it should be prepared to be called again with a new job before the previous one completes. When a task does complete, parallel() (or whatever function actually finishes the job) should inform padata of the -fact with a call to: +fact with a call to:: void padata_do_serial(struct padata_priv *padata); @@ -151,7 +154,7 @@ pains to ensure that tasks are completed in the order in which they were submitted. The one remaining function in the padata API should be called to clean up -when a padata instance is no longer needed: +when a padata instance is no longer needed:: void padata_free(struct padata_instance *pinst); diff --git a/Documentation/parport-lowlevel.txt b/Documentation/parport-lowlevel.txt index 120eb20dbb09..0633d70ffda7 100644 --- a/Documentation/parport-lowlevel.txt +++ b/Documentation/parport-lowlevel.txt @@ -1,11 +1,12 @@ +=============================== PARPORT interface documentation -------------------------------- +=============================== -Time-stamp: <2000-02-24 13:30:20 twaugh> +:Time-stamp: <2000-02-24 13:30:20 twaugh> Described here are the following functions: -Global functions: +Global functions:: parport_register_driver parport_unregister_driver parport_enumerate @@ -31,7 +32,8 @@ Global functions: parport_set_timeout Port functions (can be overridden by low-level drivers): - SPP: + + SPP:: port->ops->read_data port->ops->write_data port->ops->read_status @@ -43,23 +45,23 @@ Port functions (can be overridden by low-level drivers): port->ops->data_forward port->ops->data_reverse - EPP: + EPP:: port->ops->epp_write_data port->ops->epp_read_data port->ops->epp_write_addr port->ops->epp_read_addr - ECP: + ECP:: port->ops->ecp_write_data port->ops->ecp_read_data port->ops->ecp_write_addr - Other: + Other:: port->ops->nibble_read_data port->ops->byte_read_data port->ops->compat_write_data -The parport subsystem comprises 'parport' (the core port-sharing +The parport subsystem comprises ``parport`` (the core port-sharing code), and a variety of low-level drivers that actually do the port accesses. Each low-level driver handles a particular style of port (PC, Amiga, and so on). @@ -70,14 +72,14 @@ into global functions and port functions. The global functions are mostly for communicating between the device driver and the parport subsystem: acquiring a list of available ports, claiming a port for exclusive use, and so on. They also include -'generic' functions for doing standard things that will work on any +``generic`` functions for doing standard things that will work on any IEEE 1284-capable architecture. The port functions are provided by the low-level drivers, although the -core parport module provides generic 'defaults' for some routines. +core parport module provides generic ``defaults`` for some routines. The port functions can be split into three groups: SPP, EPP, and ECP. -SPP (Standard Parallel Port) functions modify so-called 'SPP' +SPP (Standard Parallel Port) functions modify so-called ``SPP`` registers: data, status, and control. The hardware may not actually have registers exactly like that, but the PC does and this interface is modelled after common PC implementations. Other low-level drivers may @@ -95,58 +97,63 @@ to cope with peripherals that only tenuously support IEEE 1284, a low-level driver specific function is provided, for altering 'fudge factors'. -GLOBAL FUNCTIONS ----------------- +Global functions +================ parport_register_driver - register a device driver with parport ------------------------ +--------------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -struct parport_driver { - const char *name; - void (*attach) (struct parport *); - void (*detach) (struct parport *); - struct parport_driver *next; -}; -int parport_register_driver (struct parport_driver *driver); + struct parport_driver { + const char *name; + void (*attach) (struct parport *); + void (*detach) (struct parport *); + struct parport_driver *next; + }; + int parport_register_driver (struct parport_driver *driver); DESCRIPTION +^^^^^^^^^^^ In order to be notified about parallel ports when they are detected, parport_register_driver should be called. Your driver will immediately be notified of all ports that have already been detected, and of each new port as low-level drivers are loaded. -A 'struct parport_driver' contains the textual name of your driver, +A ``struct parport_driver`` contains the textual name of your driver, a pointer to a function to handle new ports, and a pointer to a function to handle ports going away due to a low-level driver unloading. Ports will only be detached if they are not being used (i.e. there are no devices registered on them). -The visible parts of the 'struct parport *' argument given to -attach/detach are: - -struct parport -{ - struct parport *next; /* next parport in list */ - const char *name; /* port's name */ - unsigned int modes; /* bitfield of hardware modes */ - struct parport_device_info probe_info; - /* IEEE1284 info */ - int number; /* parport index */ - struct parport_operations *ops; - ... -}; +The visible parts of the ``struct parport *`` argument given to +attach/detach are:: + + struct parport + { + struct parport *next; /* next parport in list */ + const char *name; /* port's name */ + unsigned int modes; /* bitfield of hardware modes */ + struct parport_device_info probe_info; + /* IEEE1284 info */ + int number; /* parport index */ + struct parport_operations *ops; + ... + }; There are other members of the structure, but they should not be touched. -The 'modes' member summarises the capabilities of the underlying +The ``modes`` member summarises the capabilities of the underlying hardware. It consists of flags which may be bitwise-ored together: + ============================= =============================================== PARPORT_MODE_PCSPP IBM PC registers are available, i.e. functions that act on data, control and status registers are @@ -169,297 +176,351 @@ hardware. It consists of flags which may be bitwise-ored together: GFP_DMA flag with kmalloc) to the low-level driver in order to take advantage of it. + ============================= =============================================== -There may be other flags in 'modes' as well. +There may be other flags in ``modes`` as well. -The contents of 'modes' is advisory only. For example, if the -hardware is capable of DMA, and PARPORT_MODE_DMA is in 'modes', it +The contents of ``modes`` is advisory only. For example, if the +hardware is capable of DMA, and PARPORT_MODE_DMA is in ``modes``, it doesn't necessarily mean that DMA will always be used when possible. Similarly, hardware that is capable of assisting ECP transfers won't necessarily be used. RETURN VALUE +^^^^^^^^^^^^ Zero on success, otherwise an error code. ERRORS +^^^^^^ None. (Can it fail? Why return int?) EXAMPLE +^^^^^^^ -static void lp_attach (struct parport *port) -{ - ... - private = kmalloc (...); - dev[count++] = parport_register_device (...); - ... -} +:: -static void lp_detach (struct parport *port) -{ - ... -} + static void lp_attach (struct parport *port) + { + ... + private = kmalloc (...); + dev[count++] = parport_register_device (...); + ... + } -static struct parport_driver lp_driver = { - "lp", - lp_attach, - lp_detach, - NULL /* always put NULL here */ -}; + static void lp_detach (struct parport *port) + { + ... + } -int lp_init (void) -{ - ... - if (parport_register_driver (&lp_driver)) { - /* Failed; nothing we can do. */ - return -EIO; + static struct parport_driver lp_driver = { + "lp", + lp_attach, + lp_detach, + NULL /* always put NULL here */ + }; + + int lp_init (void) + { + ... + if (parport_register_driver (&lp_driver)) { + /* Failed; nothing we can do. */ + return -EIO; + } + ... } - ... -} + SEE ALSO +^^^^^^^^ parport_unregister_driver, parport_register_device, parport_enumerate - + + + parport_unregister_driver - tell parport to forget about this driver -------------------------- +-------------------------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_driver { - const char *name; - void (*attach) (struct parport *); - void (*detach) (struct parport *); - struct parport_driver *next; -}; -void parport_unregister_driver (struct parport_driver *driver); + #include <linux/parport.h> + + struct parport_driver { + const char *name; + void (*attach) (struct parport *); + void (*detach) (struct parport *); + struct parport_driver *next; + }; + void parport_unregister_driver (struct parport_driver *driver); DESCRIPTION +^^^^^^^^^^^ This tells parport not to notify the device driver of new ports or of ports going away. Registered devices belonging to that driver are NOT unregistered: parport_unregister_device must be used for each one. EXAMPLE +^^^^^^^ -void cleanup_module (void) -{ - ... - /* Stop notifications. */ - parport_unregister_driver (&lp_driver); +:: - /* Unregister devices. */ - for (i = 0; i < NUM_DEVS; i++) - parport_unregister_device (dev[i]); - ... -} + void cleanup_module (void) + { + ... + /* Stop notifications. */ + parport_unregister_driver (&lp_driver); + + /* Unregister devices. */ + for (i = 0; i < NUM_DEVS; i++) + parport_unregister_device (dev[i]); + ... + } SEE ALSO +^^^^^^^^ parport_register_driver, parport_enumerate - + + + parport_enumerate - retrieve a list of parallel ports (DEPRECATED) ------------------ +------------------------------------------------------------------ SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport *parport_enumerate (void); + #include <linux/parport.h> + + struct parport *parport_enumerate (void); DESCRIPTION +^^^^^^^^^^^ Retrieve the first of a list of valid parallel ports for this machine. -Successive parallel ports can be found using the 'struct parport -*next' element of the 'struct parport *' that is returned. If 'next' +Successive parallel ports can be found using the ``struct parport +*next`` element of the ``struct parport *`` that is returned. If ``next`` is NULL, there are no more parallel ports in the list. The number of ports in the list will not exceed PARPORT_MAX. RETURN VALUE +^^^^^^^^^^^^ -A 'struct parport *' describing a valid parallel port for the machine, +A ``struct parport *`` describing a valid parallel port for the machine, or NULL if there are none. ERRORS +^^^^^^ This function can return NULL to indicate that there are no parallel ports to use. EXAMPLE +^^^^^^^ + +:: -int detect_device (void) -{ - struct parport *port; + int detect_device (void) + { + struct parport *port; + + for (port = parport_enumerate (); + port != NULL; + port = port->next) { + /* Try to detect a device on the port... */ + ... + } + } - for (port = parport_enumerate (); - port != NULL; - port = port->next) { - /* Try to detect a device on the port... */ ... - } } - ... -} - NOTES +^^^^^ parport_enumerate is deprecated; parport_register_driver should be used instead. SEE ALSO +^^^^^^^^ parport_register_driver, parport_unregister_driver - + + + parport_register_device - register to use a port ------------------------ +------------------------------------------------ SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -typedef int (*preempt_func) (void *handle); -typedef void (*wakeup_func) (void *handle); -typedef int (*irq_func) (int irq, void *handle, struct pt_regs *); + #include <linux/parport.h> -struct pardevice *parport_register_device(struct parport *port, - const char *name, - preempt_func preempt, - wakeup_func wakeup, - irq_func irq, - int flags, - void *handle); + typedef int (*preempt_func) (void *handle); + typedef void (*wakeup_func) (void *handle); + typedef int (*irq_func) (int irq, void *handle, struct pt_regs *); + + struct pardevice *parport_register_device(struct parport *port, + const char *name, + preempt_func preempt, + wakeup_func wakeup, + irq_func irq, + int flags, + void *handle); DESCRIPTION +^^^^^^^^^^^ Use this function to register your device driver on a parallel port -('port'). Once you have done that, you will be able to use +(``port``). Once you have done that, you will be able to use parport_claim and parport_release in order to use the port. -The ('name') argument is the name of the device that appears in /proc +The (``name``) argument is the name of the device that appears in /proc filesystem. The string must be valid for the whole lifetime of the device (until parport_unregister_device is called). This function will register three callbacks into your driver: -'preempt', 'wakeup' and 'irq'. Each of these may be NULL in order to +``preempt``, ``wakeup`` and ``irq``. Each of these may be NULL in order to indicate that you do not want a callback. -When the 'preempt' function is called, it is because another driver -wishes to use the parallel port. The 'preempt' function should return +When the ``preempt`` function is called, it is because another driver +wishes to use the parallel port. The ``preempt`` function should return non-zero if the parallel port cannot be released yet -- if zero is returned, the port is lost to another driver and the port must be re-claimed before use. -The 'wakeup' function is called once another driver has released the +The ``wakeup`` function is called once another driver has released the port and no other driver has yet claimed it. You can claim the -parallel port from within the 'wakeup' function (in which case the +parallel port from within the ``wakeup`` function (in which case the claim is guaranteed to succeed), or choose not to if you don't need it now. If an interrupt occurs on the parallel port your driver has claimed, -the 'irq' function will be called. (Write something about shared +the ``irq`` function will be called. (Write something about shared interrupts here.) -The 'handle' is a pointer to driver-specific data, and is passed to +The ``handle`` is a pointer to driver-specific data, and is passed to the callback functions. -'flags' may be a bitwise combination of the following flags: +``flags`` may be a bitwise combination of the following flags: + ===================== ================================================= Flag Meaning + ===================== ================================================= PARPORT_DEV_EXCL The device cannot share the parallel port at all. Use this only when absolutely necessary. + ===================== ================================================= The typedefs are not actually defined -- they are only shown in order to make the function prototype more readable. -The visible parts of the returned 'struct pardevice' are: +The visible parts of the returned ``struct pardevice`` are:: -struct pardevice { - struct parport *port; /* Associated port */ - void *private; /* Device driver's 'handle' */ - ... -}; + struct pardevice { + struct parport *port; /* Associated port */ + void *private; /* Device driver's 'handle' */ + ... + }; RETURN VALUE +^^^^^^^^^^^^ -A 'struct pardevice *': a handle to the registered parallel port +A ``struct pardevice *``: a handle to the registered parallel port device that can be used for parport_claim, parport_release, etc. ERRORS +^^^^^^ A return value of NULL indicates that there was a problem registering a device on that port. EXAMPLE +^^^^^^^ + +:: + + static int preempt (void *handle) + { + if (busy_right_now) + return 1; + + must_reclaim_port = 1; + return 0; + } + + static void wakeup (void *handle) + { + struct toaster *private = handle; + struct pardevice *dev = private->dev; + if (!dev) return; /* avoid races */ + + if (want_port) + parport_claim (dev); + } + + static int toaster_detect (struct toaster *private, struct parport *port) + { + private->dev = parport_register_device (port, "toaster", preempt, + wakeup, NULL, 0, + private); + if (!private->dev) + /* Couldn't register with parport. */ + return -EIO; -static int preempt (void *handle) -{ - if (busy_right_now) - return 1; - - must_reclaim_port = 1; - return 0; -} - -static void wakeup (void *handle) -{ - struct toaster *private = handle; - struct pardevice *dev = private->dev; - if (!dev) return; /* avoid races */ - - if (want_port) - parport_claim (dev); -} - -static int toaster_detect (struct toaster *private, struct parport *port) -{ - private->dev = parport_register_device (port, "toaster", preempt, - wakeup, NULL, 0, - private); - if (!private->dev) - /* Couldn't register with parport. */ - return -EIO; - - must_reclaim_port = 0; - busy_right_now = 1; - parport_claim_or_block (private->dev); - ... - /* Don't need the port while the toaster warms up. */ - busy_right_now = 0; - ... - busy_right_now = 1; - if (must_reclaim_port) { - parport_claim_or_block (private->dev); must_reclaim_port = 0; + busy_right_now = 1; + parport_claim_or_block (private->dev); + ... + /* Don't need the port while the toaster warms up. */ + busy_right_now = 0; + ... + busy_right_now = 1; + if (must_reclaim_port) { + parport_claim_or_block (private->dev); + must_reclaim_port = 0; + } + ... } - ... -} SEE ALSO +^^^^^^^^ parport_unregister_device, parport_claim + + parport_unregister_device - finish using a port -------------------------- +----------------------------------------------- SYNPOPSIS -#include <linux/parport.h> +:: + + #include <linux/parport.h> -void parport_unregister_device (struct pardevice *dev); + void parport_unregister_device (struct pardevice *dev); DESCRIPTION +^^^^^^^^^^^ This function is the opposite of parport_register_device. After using -parport_unregister_device, 'dev' is no longer a valid device handle. +parport_unregister_device, ``dev`` is no longer a valid device handle. You should not unregister a device that is currently claimed, although if you do it will be released automatically. EXAMPLE +^^^^^^^ + +:: ... kfree (dev->private); /* before we lose the pointer */ @@ -467,460 +528,602 @@ EXAMPLE ... SEE ALSO +^^^^^^^^ + parport_unregister_driver parport_claim, parport_claim_or_block - claim the parallel port for a device -------------------------------------- +---------------------------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -int parport_claim (struct pardevice *dev); -int parport_claim_or_block (struct pardevice *dev); + int parport_claim (struct pardevice *dev); + int parport_claim_or_block (struct pardevice *dev); DESCRIPTION +^^^^^^^^^^^ These functions attempt to gain control of the parallel port on which -'dev' is registered. 'parport_claim' does not block, but -'parport_claim_or_block' may do. (Put something here about blocking +``dev`` is registered. ``parport_claim`` does not block, but +``parport_claim_or_block`` may do. (Put something here about blocking interruptibly or non-interruptibly.) You should not try to claim a port that you have already claimed. RETURN VALUE +^^^^^^^^^^^^ A return value of zero indicates that the port was successfully claimed, and the caller now has possession of the parallel port. -If 'parport_claim_or_block' blocks before returning successfully, the +If ``parport_claim_or_block`` blocks before returning successfully, the return value is positive. ERRORS +^^^^^^ +========== ========================================================== -EAGAIN The port is unavailable at the moment, but another attempt to claim it may succeed. +========== ========================================================== SEE ALSO +^^^^^^^^ + parport_release parport_release - release the parallel port ---------------- +------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -void parport_release (struct pardevice *dev); + void parport_release (struct pardevice *dev); DESCRIPTION +^^^^^^^^^^^ Once a parallel port device has been claimed, it can be released using -'parport_release'. It cannot fail, but you should not release a +``parport_release``. It cannot fail, but you should not release a device that you do not have possession of. EXAMPLE +^^^^^^^ -static size_t write (struct pardevice *dev, const void *buf, - size_t len) -{ - ... - written = dev->port->ops->write_ecp_data (dev->port, buf, - len); - parport_release (dev); - ... -} +:: + + static size_t write (struct pardevice *dev, const void *buf, + size_t len) + { + ... + written = dev->port->ops->write_ecp_data (dev->port, buf, + len); + parport_release (dev); + ... + } SEE ALSO +^^^^^^^^ change_mode, parport_claim, parport_claim_or_block, parport_yield - + + + parport_yield, parport_yield_blocking - temporarily release a parallel port -------------------------------------- +--------------------------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -int parport_yield (struct pardevice *dev) -int parport_yield_blocking (struct pardevice *dev); + int parport_yield (struct pardevice *dev) + int parport_yield_blocking (struct pardevice *dev); DESCRIPTION +^^^^^^^^^^^ When a driver has control of a parallel port, it may allow another -driver to temporarily 'borrow' it. 'parport_yield' does not block; -'parport_yield_blocking' may do. +driver to temporarily ``borrow`` it. ``parport_yield`` does not block; +``parport_yield_blocking`` may do. RETURN VALUE +^^^^^^^^^^^^ A return value of zero indicates that the caller still owns the port and the call did not block. -A positive return value from 'parport_yield_blocking' indicates that +A positive return value from ``parport_yield_blocking`` indicates that the caller still owns the port and the call blocked. A return value of -EAGAIN indicates that the caller no longer owns the port, and it must be re-claimed before use. ERRORS +^^^^^^ +========= ========================================================== -EAGAIN Ownership of the parallel port was given away. +========= ========================================================== SEE ALSO +^^^^^^^^ parport_release + + parport_wait_peripheral - wait for status lines, up to 35ms ------------------------ +----------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -int parport_wait_peripheral (struct parport *port, - unsigned char mask, - unsigned char val); + int parport_wait_peripheral (struct parport *port, + unsigned char mask, + unsigned char val); DESCRIPTION +^^^^^^^^^^^ Wait for the status lines in mask to match the values in val. RETURN VALUE +^^^^^^^^^^^^ +======== ========================================================== -EINTR a signal is pending 0 the status lines in mask have values in val 1 timed out while waiting (35ms elapsed) +======== ========================================================== SEE ALSO +^^^^^^^^ parport_poll_peripheral + + parport_poll_peripheral - wait for status lines, in usec ------------------------ +-------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -int parport_poll_peripheral (struct parport *port, - unsigned char mask, - unsigned char val, - int usec); + int parport_poll_peripheral (struct parport *port, + unsigned char mask, + unsigned char val, + int usec); DESCRIPTION +^^^^^^^^^^^ Wait for the status lines in mask to match the values in val. RETURN VALUE +^^^^^^^^^^^^ +======== ========================================================== -EINTR a signal is pending 0 the status lines in mask have values in val 1 timed out while waiting (usec microseconds have elapsed) +======== ========================================================== SEE ALSO +^^^^^^^^ parport_wait_peripheral - + + + parport_wait_event - wait for an event on a port ------------------- +------------------------------------------------ SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -int parport_wait_event (struct parport *port, signed long timeout) + #include <linux/parport.h> + + int parport_wait_event (struct parport *port, signed long timeout) DESCRIPTION +^^^^^^^^^^^ Wait for an event (e.g. interrupt) on a port. The timeout is in jiffies. RETURN VALUE +^^^^^^^^^^^^ +======= ========================================================== 0 success <0 error (exit as soon as possible) >0 timed out - +======= ========================================================== + parport_negotiate - perform IEEE 1284 negotiation ------------------ +------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -int parport_negotiate (struct parport *, int mode); + int parport_negotiate (struct parport *, int mode); DESCRIPTION +^^^^^^^^^^^ Perform IEEE 1284 negotiation. RETURN VALUE +^^^^^^^^^^^^ +======= ========================================================== 0 handshake OK; IEEE 1284 peripheral and mode available -1 handshake failed; peripheral not compliant (or none present) 1 handshake OK; IEEE 1284 peripheral present but mode not available +======= ========================================================== SEE ALSO +^^^^^^^^ parport_read, parport_write - + + + parport_read - read data from device ------------- +------------------------------------ SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -ssize_t parport_read (struct parport *, void *buf, size_t len); + ssize_t parport_read (struct parport *, void *buf, size_t len); DESCRIPTION +^^^^^^^^^^^ Read data from device in current IEEE 1284 transfer mode. This only works for modes that support reverse data transfer. RETURN VALUE +^^^^^^^^^^^^ If negative, an error code; otherwise the number of bytes transferred. SEE ALSO +^^^^^^^^ parport_write, parport_negotiate - + + + parport_write - write data to device -------------- +------------------------------------ SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -ssize_t parport_write (struct parport *, const void *buf, size_t len); + ssize_t parport_write (struct parport *, const void *buf, size_t len); DESCRIPTION +^^^^^^^^^^^ Write data to device in current IEEE 1284 transfer mode. This only works for modes that support forward data transfer. RETURN VALUE +^^^^^^^^^^^^ If negative, an error code; otherwise the number of bytes transferred. SEE ALSO +^^^^^^^^ parport_read, parport_negotiate + + parport_open - register device for particular device number ------------- +----------------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct pardevice *parport_open (int devnum, const char *name, - int (*pf) (void *), - void (*kf) (void *), - void (*irqf) (int, void *, - struct pt_regs *), - int flags, void *handle); + #include <linux/parport.h> + + struct pardevice *parport_open (int devnum, const char *name, + int (*pf) (void *), + void (*kf) (void *), + void (*irqf) (int, void *, + struct pt_regs *), + int flags, void *handle); DESCRIPTION +^^^^^^^^^^^ This is like parport_register_device but takes a device number instead of a pointer to a struct parport. RETURN VALUE +^^^^^^^^^^^^ See parport_register_device. If no device is associated with devnum, NULL is returned. SEE ALSO +^^^^^^^^ parport_register_device - + + + parport_close - unregister device for particular device number -------------- +-------------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -void parport_close (struct pardevice *dev); + void parport_close (struct pardevice *dev); DESCRIPTION +^^^^^^^^^^^ This is the equivalent of parport_unregister_device for parport_open. SEE ALSO +^^^^^^^^ parport_unregister_device, parport_open - + + + parport_device_id - obtain IEEE 1284 Device ID ------------------ +---------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -ssize_t parport_device_id (int devnum, char *buffer, size_t len); + ssize_t parport_device_id (int devnum, char *buffer, size_t len); DESCRIPTION +^^^^^^^^^^^ Obtains the IEEE 1284 Device ID associated with a given device. RETURN VALUE +^^^^^^^^^^^^ If negative, an error code; otherwise, the number of bytes of buffer that contain the device ID. The format of the device ID is as -follows: +follows:: -[length][ID] + [length][ID] The first two bytes indicate the inclusive length of the entire Device ID, and are in big-endian order. The ID is a sequence of pairs of the -form: +form:: -key:value; + key:value; NOTES +^^^^^ Many devices have ill-formed IEEE 1284 Device IDs. SEE ALSO +^^^^^^^^ parport_find_class, parport_find_device - + + + parport_device_coords - convert device number to device coordinates ------------------- +------------------------------------------------------------------- SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -int parport_device_coords (int devnum, int *parport, int *mux, - int *daisy); + int parport_device_coords (int devnum, int *parport, int *mux, + int *daisy); DESCRIPTION +^^^^^^^^^^^ Convert between device number (zero-based) and device coordinates (port, multiplexor, daisy chain address). RETURN VALUE +^^^^^^^^^^^^ -Zero on success, in which case the coordinates are (*parport, *mux, -*daisy). +Zero on success, in which case the coordinates are (``*parport``, ``*mux``, +``*daisy``). SEE ALSO +^^^^^^^^ parport_open, parport_device_id - + + + parport_find_class - find a device by its class ------------------- +----------------------------------------------- SYNOPSIS - -#include <linux/parport.h> - -typedef enum { - PARPORT_CLASS_LEGACY = 0, /* Non-IEEE1284 device */ - PARPORT_CLASS_PRINTER, - PARPORT_CLASS_MODEM, - PARPORT_CLASS_NET, - PARPORT_CLASS_HDC, /* Hard disk controller */ - PARPORT_CLASS_PCMCIA, - PARPORT_CLASS_MEDIA, /* Multimedia device */ - PARPORT_CLASS_FDC, /* Floppy disk controller */ - PARPORT_CLASS_PORTS, - PARPORT_CLASS_SCANNER, - PARPORT_CLASS_DIGCAM, - PARPORT_CLASS_OTHER, /* Anything else */ - PARPORT_CLASS_UNSPEC, /* No CLS field in ID */ - PARPORT_CLASS_SCSIADAPTER -} parport_device_class; - -int parport_find_class (parport_device_class cls, int from); +^^^^^^^^ + +:: + + #include <linux/parport.h> + + typedef enum { + PARPORT_CLASS_LEGACY = 0, /* Non-IEEE1284 device */ + PARPORT_CLASS_PRINTER, + PARPORT_CLASS_MODEM, + PARPORT_CLASS_NET, + PARPORT_CLASS_HDC, /* Hard disk controller */ + PARPORT_CLASS_PCMCIA, + PARPORT_CLASS_MEDIA, /* Multimedia device */ + PARPORT_CLASS_FDC, /* Floppy disk controller */ + PARPORT_CLASS_PORTS, + PARPORT_CLASS_SCANNER, + PARPORT_CLASS_DIGCAM, + PARPORT_CLASS_OTHER, /* Anything else */ + PARPORT_CLASS_UNSPEC, /* No CLS field in ID */ + PARPORT_CLASS_SCSIADAPTER + } parport_device_class; + + int parport_find_class (parport_device_class cls, int from); DESCRIPTION +^^^^^^^^^^^ Find a device by class. The search starts from device number from+1. RETURN VALUE +^^^^^^^^^^^^ The device number of the next device in that class, or -1 if no such device exists. NOTES +^^^^^ -Example usage: +Example usage:: -int devnum = -1; -while ((devnum = parport_find_class (PARPORT_CLASS_DIGCAM, devnum)) != -1) { - struct pardevice *dev = parport_open (devnum, ...); - ... -} + int devnum = -1; + while ((devnum = parport_find_class (PARPORT_CLASS_DIGCAM, devnum)) != -1) { + struct pardevice *dev = parport_open (devnum, ...); + ... + } SEE ALSO +^^^^^^^^ parport_find_device, parport_open, parport_device_id - + + + parport_find_device - find a device by its class ------------------- +------------------------------------------------ SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -int parport_find_device (const char *mfg, const char *mdl, int from); + #include <linux/parport.h> + + int parport_find_device (const char *mfg, const char *mdl, int from); DESCRIPTION +^^^^^^^^^^^ Find a device by vendor and model. The search starts from device number from+1. RETURN VALUE +^^^^^^^^^^^^ The device number of the next device matching the specifications, or -1 if no such device exists. NOTES +^^^^^ -Example usage: +Example usage:: -int devnum = -1; -while ((devnum = parport_find_device ("IOMEGA", "ZIP+", devnum)) != -1) { - struct pardevice *dev = parport_open (devnum, ...); - ... -} + int devnum = -1; + while ((devnum = parport_find_device ("IOMEGA", "ZIP+", devnum)) != -1) { + struct pardevice *dev = parport_open (devnum, ...); + ... + } SEE ALSO +^^^^^^^^ parport_find_class, parport_open, parport_device_id + + parport_set_timeout - set the inactivity timeout -------------------- +------------------------------------------------ SYNOPSIS +^^^^^^^^ + +:: -#include <linux/parport.h> + #include <linux/parport.h> -long parport_set_timeout (struct pardevice *dev, long inactivity); + long parport_set_timeout (struct pardevice *dev, long inactivity); DESCRIPTION +^^^^^^^^^^^ Set the inactivity timeout, in jiffies, for a registered device. The previous timeout is returned. RETURN VALUE +^^^^^^^^^^^^ The previous timeout, in jiffies. NOTES +^^^^^ Some of the port->ops functions for a parport may take time, owing to delays at the peripheral. After the peripheral has not responded for -'inactivity' jiffies, a timeout will occur and the blocking function +``inactivity`` jiffies, a timeout will occur and the blocking function will return. A timeout of 0 jiffies is a special case: the function must do as much @@ -932,29 +1135,37 @@ Once set for a registered device, the timeout will remain at the set value until set again. SEE ALSO +^^^^^^^^ port->ops->xxx_read/write_yyy - + + + + PORT FUNCTIONS --------------- +============== The functions in the port->ops structure (struct parport_operations) are provided by the low-level driver responsible for that port. port->ops->read_data - read the data register --------------------- +--------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - unsigned char (*read_data) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + unsigned char (*read_data) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ If port->modes contains the PARPORT_MODE_TRISTATE flag and the PARPORT_CONTROL_DIRECTION bit in the control register is set, this @@ -964,45 +1175,59 @@ not set, the return value _may_ be the last value written to the data register. Otherwise the return value is undefined. SEE ALSO +^^^^^^^^ write_data, read_status, write_control + + port->ops->write_data - write the data register ---------------------- +----------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - void (*write_data) (struct parport *port, unsigned char d); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + void (*write_data) (struct parport *port, unsigned char d); + ... + }; DESCRIPTION +^^^^^^^^^^^ Writes to the data register. May have side-effects (a STROBE pulse, for instance). SEE ALSO +^^^^^^^^ read_data, read_status, write_control + + port->ops->read_status - read the status register ----------------------- +------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - unsigned char (*read_status) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + unsigned char (*read_status) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ Reads from the status register. This is a bitmask: @@ -1015,76 +1240,98 @@ Reads from the status register. This is a bitmask: There may be other bits set. SEE ALSO +^^^^^^^^ read_data, write_data, write_control + + port->ops->read_control - read the control register ------------------------ +--------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - unsigned char (*read_control) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + unsigned char (*read_control) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ Returns the last value written to the control register (either from write_control or frob_control). No port access is performed. SEE ALSO +^^^^^^^^ read_data, write_data, read_status, write_control + + port->ops->write_control - write the control register ------------------------- +----------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - void (*write_control) (struct parport *port, unsigned char s); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + void (*write_control) (struct parport *port, unsigned char s); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Writes to the control register. This is a bitmask: - _______ -- PARPORT_CONTROL_STROBE (nStrobe) - _______ -- PARPORT_CONTROL_AUTOFD (nAutoFd) - _____ -- PARPORT_CONTROL_INIT (nInit) - _________ -- PARPORT_CONTROL_SELECT (nSelectIn) +Writes to the control register. This is a bitmask:: + + _______ + - PARPORT_CONTROL_STROBE (nStrobe) + _______ + - PARPORT_CONTROL_AUTOFD (nAutoFd) + _____ + - PARPORT_CONTROL_INIT (nInit) + _________ + - PARPORT_CONTROL_SELECT (nSelectIn) SEE ALSO +^^^^^^^^ read_data, write_data, read_status, frob_control + + port->ops->frob_control - write control register bits ------------------------ +----------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - unsigned char (*frob_control) (struct parport *port, - unsigned char mask, - unsigned char val); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + unsigned char (*frob_control) (struct parport *port, + unsigned char mask, + unsigned char val); + ... + }; DESCRIPTION +^^^^^^^^^^^ This is equivalent to reading from the control register, masking out the bits in mask, exclusive-or'ing with the bits in val, and writing @@ -1095,23 +1342,30 @@ of its contents is maintained, so frob_control is in fact only one port access. SEE ALSO +^^^^^^^^ read_data, write_data, read_status, write_control + + port->ops->enable_irq - enable interrupt generation ---------------------- +--------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - void (*enable_irq) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + void (*enable_irq) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ The parallel port hardware is instructed to generate interrupts at appropriate moments, although those moments are @@ -1119,353 +1373,460 @@ architecture-specific. For the PC architecture, interrupts are commonly generated on the rising edge of nAck. SEE ALSO +^^^^^^^^ disable_irq + + port->ops->disable_irq - disable interrupt generation ----------------------- +----------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - void (*disable_irq) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + void (*disable_irq) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ The parallel port hardware is instructed not to generate interrupts. The interrupt itself is not masked. SEE ALSO +^^^^^^^^ enable_irq + + port->ops->data_forward - enable data drivers ------------------------ +--------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - void (*data_forward) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + void (*data_forward) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ Enables the data line drivers, for 8-bit host-to-peripheral communications. SEE ALSO +^^^^^^^^ data_reverse + + port->ops->data_reverse - tristate the buffer ------------------------ +--------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - void (*data_reverse) (struct parport *port); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + void (*data_reverse) (struct parport *port); + ... + }; DESCRIPTION +^^^^^^^^^^^ Places the data bus in a high impedance state, if port->modes has the PARPORT_MODE_TRISTATE bit set. SEE ALSO +^^^^^^^^ data_forward - + + + port->ops->epp_write_data - write EPP data -------------------------- +------------------------------------------ SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*epp_write_data) (struct parport *port, const void *buf, - size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*epp_write_data) (struct parport *port, const void *buf, + size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ Writes data in EPP mode, and returns the number of bytes written. -The 'flags' parameter may be one or more of the following, +The ``flags`` parameter may be one or more of the following, bitwise-or'ed together: +======================= ================================================= PARPORT_EPP_FAST Use fast transfers. Some chips provide 16-bit and 32-bit registers. However, if a transfer times out, the return value may be unreliable. +======================= ================================================= SEE ALSO +^^^^^^^^ epp_read_data, epp_write_addr, epp_read_addr + + port->ops->epp_read_data - read EPP data ------------------------- +---------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*epp_read_data) (struct parport *port, void *buf, - size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*epp_read_data) (struct parport *port, void *buf, + size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ Reads data in EPP mode, and returns the number of bytes read. -The 'flags' parameter may be one or more of the following, +The ``flags`` parameter may be one or more of the following, bitwise-or'ed together: +======================= ================================================= PARPORT_EPP_FAST Use fast transfers. Some chips provide 16-bit and 32-bit registers. However, if a transfer times out, the return value may be unreliable. +======================= ================================================= SEE ALSO +^^^^^^^^ epp_write_data, epp_write_addr, epp_read_addr - + + + port->ops->epp_write_addr - write EPP address -------------------------- +--------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*epp_write_addr) (struct parport *port, - const void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*epp_write_addr) (struct parport *port, + const void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ Writes EPP addresses (8 bits each), and returns the number written. -The 'flags' parameter may be one or more of the following, +The ``flags`` parameter may be one or more of the following, bitwise-or'ed together: +======================= ================================================= PARPORT_EPP_FAST Use fast transfers. Some chips provide 16-bit and 32-bit registers. However, if a transfer times out, the return value may be unreliable. +======================= ================================================= (Does PARPORT_EPP_FAST make sense for this function?) SEE ALSO +^^^^^^^^ epp_write_data, epp_read_data, epp_read_addr + + port->ops->epp_read_addr - read EPP address ------------------------- +------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*epp_read_addr) (struct parport *port, void *buf, - size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*epp_read_addr) (struct parport *port, void *buf, + size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ Reads EPP addresses (8 bits each), and returns the number read. -The 'flags' parameter may be one or more of the following, +The ``flags`` parameter may be one or more of the following, bitwise-or'ed together: +======================= ================================================= PARPORT_EPP_FAST Use fast transfers. Some chips provide 16-bit and 32-bit registers. However, if a transfer times out, the return value may be unreliable. +======================= ================================================= (Does PARPORT_EPP_FAST make sense for this function?) SEE ALSO +^^^^^^^^ epp_write_data, epp_read_data, epp_write_addr + + port->ops->ecp_write_data - write a block of ECP data -------------------------- +----------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*ecp_write_data) (struct parport *port, - const void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*ecp_write_data) (struct parport *port, + const void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Writes a block of ECP data. The 'flags' parameter is ignored. +Writes a block of ECP data. The ``flags`` parameter is ignored. RETURN VALUE +^^^^^^^^^^^^ The number of bytes written. SEE ALSO +^^^^^^^^ ecp_read_data, ecp_write_addr + + port->ops->ecp_read_data - read a block of ECP data ------------------------- +--------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*ecp_read_data) (struct parport *port, - void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*ecp_read_data) (struct parport *port, + void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Reads a block of ECP data. The 'flags' parameter is ignored. +Reads a block of ECP data. The ``flags`` parameter is ignored. RETURN VALUE +^^^^^^^^^^^^ The number of bytes read. NB. There may be more unread data in a FIFO. Is there a way of stunning the FIFO to prevent this? SEE ALSO +^^^^^^^^ ecp_write_block, ecp_write_addr - + + + port->ops->ecp_write_addr - write a block of ECP addresses -------------------------- +---------------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*ecp_write_addr) (struct parport *port, - const void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*ecp_write_addr) (struct parport *port, + const void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Writes a block of ECP addresses. The 'flags' parameter is ignored. +Writes a block of ECP addresses. The ``flags`` parameter is ignored. RETURN VALUE +^^^^^^^^^^^^ The number of bytes written. NOTES +^^^^^ This may use a FIFO, and if so shall not return until the FIFO is empty. SEE ALSO +^^^^^^^^ ecp_read_data, ecp_write_data - + + + port->ops->nibble_read_data - read a block of data in nibble mode ---------------------------- +----------------------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*nibble_read_data) (struct parport *port, - void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*nibble_read_data) (struct parport *port, + void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Reads a block of data in nibble mode. The 'flags' parameter is ignored. +Reads a block of data in nibble mode. The ``flags`` parameter is ignored. RETURN VALUE +^^^^^^^^^^^^ The number of whole bytes read. SEE ALSO +^^^^^^^^ byte_read_data, compat_write_data + + port->ops->byte_read_data - read a block of data in byte mode -------------------------- +------------------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*byte_read_data) (struct parport *port, - void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*byte_read_data) (struct parport *port, + void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Reads a block of data in byte mode. The 'flags' parameter is ignored. +Reads a block of data in byte mode. The ``flags`` parameter is ignored. RETURN VALUE +^^^^^^^^^^^^ The number of bytes read. SEE ALSO +^^^^^^^^ nibble_read_data, compat_write_data + + port->ops->compat_write_data - write a block of data in compatibility mode ----------------------------- +-------------------------------------------------------------------------- SYNOPSIS +^^^^^^^^ -#include <linux/parport.h> +:: -struct parport_operations { - ... - size_t (*compat_write_data) (struct parport *port, - const void *buf, size_t len, int flags); - ... -}; + #include <linux/parport.h> + + struct parport_operations { + ... + size_t (*compat_write_data) (struct parport *port, + const void *buf, size_t len, int flags); + ... + }; DESCRIPTION +^^^^^^^^^^^ -Writes a block of data in compatibility mode. The 'flags' parameter +Writes a block of data in compatibility mode. The ``flags`` parameter is ignored. RETURN VALUE +^^^^^^^^^^^^ The number of bytes written. SEE ALSO +^^^^^^^^ nibble_read_data, byte_read_data diff --git a/Documentation/percpu-rw-semaphore.txt b/Documentation/percpu-rw-semaphore.txt index 7d3c82431909..247de6410855 100644 --- a/Documentation/percpu-rw-semaphore.txt +++ b/Documentation/percpu-rw-semaphore.txt @@ -1,5 +1,6 @@ +==================== Percpu rw semaphores --------------------- +==================== Percpu rw semaphores is a new read-write semaphore design that is optimized for locking for reading. diff --git a/Documentation/phy.txt b/Documentation/phy.txt index 383cdd863f08..457c3e0f86d6 100644 --- a/Documentation/phy.txt +++ b/Documentation/phy.txt @@ -1,10 +1,14 @@ - PHY SUBSYSTEM - Kishon Vijay Abraham I <kishon@ti.com> +============= +PHY subsystem +============= + +:Author: Kishon Vijay Abraham I <kishon@ti.com> This document explains the Generic PHY Framework along with the APIs provided, and how-to-use. -1. Introduction +Introduction +============ *PHY* is the abbreviation for physical layer. It is used to connect a device to the physical medium e.g., the USB controller has a PHY to provide functions @@ -21,7 +25,8 @@ better code maintainability. This framework will be of use only to devices that use external PHY (PHY functionality is not embedded within the controller). -2. Registering/Unregistering the PHY provider +Registering/Unregistering the PHY provider +========================================== PHY provider refers to an entity that implements one or more PHY instances. For the simple case where the PHY provider implements only a single instance of @@ -30,11 +35,14 @@ of_phy_simple_xlate. If the PHY provider implements multiple instances, it should provide its own implementation of of_xlate. of_xlate is used only for dt boot case. -#define of_phy_provider_register(dev, xlate) \ - __of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate)) +:: + + #define of_phy_provider_register(dev, xlate) \ + __of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate)) -#define devm_of_phy_provider_register(dev, xlate) \ - __devm_of_phy_provider_register((dev), NULL, THIS_MODULE, (xlate)) + #define devm_of_phy_provider_register(dev, xlate) \ + __devm_of_phy_provider_register((dev), NULL, THIS_MODULE, + (xlate)) of_phy_provider_register and devm_of_phy_provider_register macros can be used to register the phy_provider and it takes device and of_xlate as @@ -47,28 +55,35 @@ nodes within extra levels for context and extensibility, in which case the low level of_phy_provider_register_full() and devm_of_phy_provider_register_full() macros can be used to override the node containing the children. -#define of_phy_provider_register_full(dev, children, xlate) \ - __of_phy_provider_register(dev, children, THIS_MODULE, xlate) +:: + + #define of_phy_provider_register_full(dev, children, xlate) \ + __of_phy_provider_register(dev, children, THIS_MODULE, xlate) -#define devm_of_phy_provider_register_full(dev, children, xlate) \ - __devm_of_phy_provider_register_full(dev, children, THIS_MODULE, xlate) + #define devm_of_phy_provider_register_full(dev, children, xlate) \ + __devm_of_phy_provider_register_full(dev, children, + THIS_MODULE, xlate) -void devm_of_phy_provider_unregister(struct device *dev, - struct phy_provider *phy_provider); -void of_phy_provider_unregister(struct phy_provider *phy_provider); + void devm_of_phy_provider_unregister(struct device *dev, + struct phy_provider *phy_provider); + void of_phy_provider_unregister(struct phy_provider *phy_provider); devm_of_phy_provider_unregister and of_phy_provider_unregister can be used to unregister the PHY. -3. Creating the PHY +Creating the PHY +================ The PHY driver should create the PHY in order for other peripheral controllers to make use of it. The PHY framework provides 2 APIs to create the PHY. -struct phy *phy_create(struct device *dev, struct device_node *node, - const struct phy_ops *ops); -struct phy *devm_phy_create(struct device *dev, struct device_node *node, - const struct phy_ops *ops); +:: + + struct phy *phy_create(struct device *dev, struct device_node *node, + const struct phy_ops *ops); + struct phy *devm_phy_create(struct device *dev, + struct device_node *node, + const struct phy_ops *ops); The PHY drivers can use one of the above 2 APIs to create the PHY by passing the device pointer and phy ops. @@ -84,12 +99,16 @@ phy_ops to get back the private data. Before the controller can make use of the PHY, it has to get a reference to it. This framework provides the following APIs to get a reference to the PHY. -struct phy *phy_get(struct device *dev, const char *string); -struct phy *phy_optional_get(struct device *dev, const char *string); -struct phy *devm_phy_get(struct device *dev, const char *string); -struct phy *devm_phy_optional_get(struct device *dev, const char *string); -struct phy *devm_of_phy_get_by_index(struct device *dev, struct device_node *np, - int index); +:: + + struct phy *phy_get(struct device *dev, const char *string); + struct phy *phy_optional_get(struct device *dev, const char *string); + struct phy *devm_phy_get(struct device *dev, const char *string); + struct phy *devm_phy_optional_get(struct device *dev, + const char *string); + struct phy *devm_of_phy_get_by_index(struct device *dev, + struct device_node *np, + int index); phy_get, phy_optional_get, devm_phy_get and devm_phy_optional_get can be used to get the PHY. In the case of dt boot, the string arguments @@ -111,30 +130,35 @@ the phy_init() and phy_exit() calls, and phy_power_on() and phy_power_off() calls are all NOP when applied to a NULL phy. The NULL phy is useful in devices for handling optional phy devices. -5. Releasing a reference to the PHY +Releasing a reference to the PHY +================================ When the controller no longer needs the PHY, it has to release the reference to the PHY it has obtained using the APIs mentioned in the above section. The PHY framework provides 2 APIs to release a reference to the PHY. -void phy_put(struct phy *phy); -void devm_phy_put(struct device *dev, struct phy *phy); +:: + + void phy_put(struct phy *phy); + void devm_phy_put(struct device *dev, struct phy *phy); Both these APIs are used to release a reference to the PHY and devm_phy_put destroys the devres associated with this PHY. -6. Destroying the PHY +Destroying the PHY +================== When the driver that created the PHY is unloaded, it should destroy the PHY it -created using one of the following 2 APIs. +created using one of the following 2 APIs:: -void phy_destroy(struct phy *phy); -void devm_phy_destroy(struct device *dev, struct phy *phy); + void phy_destroy(struct phy *phy); + void devm_phy_destroy(struct device *dev, struct phy *phy); Both these APIs destroy the PHY and devm_phy_destroy destroys the devres associated with this PHY. -7. PM Runtime +PM Runtime +========== This subsystem is pm runtime enabled. So while creating the PHY, pm_runtime_enable of the phy device created by this subsystem is called and @@ -150,7 +174,8 @@ There are exported APIs like phy_pm_runtime_get, phy_pm_runtime_get_sync, phy_pm_runtime_put, phy_pm_runtime_put_sync, phy_pm_runtime_allow and phy_pm_runtime_forbid for performing PM operations. -8. PHY Mappings +PHY Mappings +============ In order to get reference to a PHY without help from DeviceTree, the framework offers lookups which can be compared to clkdev that allow clk structures to be @@ -158,12 +183,15 @@ bound to devices. A lookup can be made be made during runtime when a handle to the struct phy already exists. The framework offers the following API for registering and unregistering the -lookups. +lookups:: -int phy_create_lookup(struct phy *phy, const char *con_id, const char *dev_id); -void phy_remove_lookup(struct phy *phy, const char *con_id, const char *dev_id); + int phy_create_lookup(struct phy *phy, const char *con_id, + const char *dev_id); + void phy_remove_lookup(struct phy *phy, const char *con_id, + const char *dev_id); -9. DeviceTree Binding +DeviceTree Binding +================== The documentation for PHY dt binding can be found @ Documentation/devicetree/bindings/phy/phy-bindings.txt diff --git a/Documentation/pi-futex.txt b/Documentation/pi-futex.txt index 9a5bc8651c29..aafddbee7377 100644 --- a/Documentation/pi-futex.txt +++ b/Documentation/pi-futex.txt @@ -1,5 +1,6 @@ +====================== Lightweight PI-futexes ----------------------- +====================== We are calling them lightweight for 3 reasons: @@ -25,8 +26,8 @@ determinism and well-bound latencies. Even in the worst-case, PI will improve the statistical distribution of locking related application delays. -The longer reply: ------------------ +The longer reply +---------------- Firstly, sharing locks between multiple tasks is a common programming technique that often cannot be replaced with lockless algorithms. As we @@ -71,8 +72,8 @@ deterministic execution of the high-prio task: any medium-priority task could preempt the low-prio task while it holds the shared lock and executes the critical section, and could delay it indefinitely. -Implementation: ---------------- +Implementation +-------------- As mentioned before, the userspace fastpath of PI-enabled pthread mutexes involves no kernel work at all - they behave quite similarly to @@ -83,8 +84,8 @@ entering the kernel. To handle the slowpath, we have added two new futex ops: - FUTEX_LOCK_PI - FUTEX_UNLOCK_PI + - FUTEX_LOCK_PI + - FUTEX_UNLOCK_PI If the lock-acquire fastpath fails, [i.e. an atomic transition from 0 to TID fails], then FUTEX_LOCK_PI is called. The kernel does all the diff --git a/Documentation/pnp.txt b/Documentation/pnp.txt index 763e4659bf18..bab2d10631f0 100644 --- a/Documentation/pnp.txt +++ b/Documentation/pnp.txt @@ -1,98 +1,118 @@ +================================= Linux Plug and Play Documentation -by Adam Belay <ambx1@neo.rr.com> -last updated: Oct. 16, 2002 ---------------------------------------------------------------------------------------- +================================= +:Author: Adam Belay <ambx1@neo.rr.com> +:Last updated: Oct. 16, 2002 Overview -------- - Plug and Play provides a means of detecting and setting resources for legacy or + +Plug and Play provides a means of detecting and setting resources for legacy or otherwise unconfigurable devices. The Linux Plug and Play Layer provides these services to compatible drivers. - The User Interface ------------------ - The Linux Plug and Play user interface provides a means to activate PnP devices + +The Linux Plug and Play user interface provides a means to activate PnP devices for legacy and user level drivers that do not support Linux Plug and Play. The user interface is integrated into sysfs. In addition to the standard sysfs file the following are created in each device's directory: -id - displays a list of support EISA IDs -options - displays possible resource configurations -resources - displays currently allocated resources and allows resource changes +- id - displays a list of support EISA IDs +- options - displays possible resource configurations +- resources - displays currently allocated resources and allows resource changes --activating a device +activating a device +^^^^^^^^^^^^^^^^^^^ -#echo "auto" > resources +:: + + # echo "auto" > resources this will invoke the automatic resource config system to activate the device --manually activating a device +manually activating a device +^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +:: + + # echo "manual <depnum> <mode>" > resources -#echo "manual <depnum> <mode>" > resources -<depnum> - the configuration number -<mode> - static or dynamic - static = for next boot - dynamic = now + <depnum> - the configuration number + <mode> - static or dynamic + static = for next boot + dynamic = now --disabling a device +disabling a device +^^^^^^^^^^^^^^^^^^ -#echo "disable" > resources +:: + + # echo "disable" > resources EXAMPLE: Suppose you need to activate the floppy disk controller. -1.) change to the proper directory, in my case it is -/driver/bus/pnp/devices/00:0f -# cd /driver/bus/pnp/devices/00:0f -# cat name -PC standard floppy disk controller - -2.) check if the device is already active -# cat resources -DISABLED - -- Notice the string "DISABLED". This means the device is not active. - -3.) check the device's possible configurations (optional) -# cat options -Dependent: 01 - Priority acceptable - port 0x3f0-0x3f0, align 0x7, size 0x6, 16-bit address decoding - port 0x3f7-0x3f7, align 0x0, size 0x1, 16-bit address decoding - irq 6 - dma 2 8-bit compatible -Dependent: 02 - Priority acceptable - port 0x370-0x370, align 0x7, size 0x6, 16-bit address decoding - port 0x377-0x377, align 0x0, size 0x1, 16-bit address decoding - irq 6 - dma 2 8-bit compatible - -4.) now activate the device -# echo "auto" > resources - -5.) finally check if the device is active -# cat resources -io 0x3f0-0x3f5 -io 0x3f7-0x3f7 -irq 6 -dma 2 - -also there are a series of kernel parameters: -pnp_reserve_irq=irq1[,irq2] .... -pnp_reserve_dma=dma1[,dma2] .... -pnp_reserve_io=io1,size1[,io2,size2] .... -pnp_reserve_mem=mem1,size1[,mem2,size2] .... + +1. change to the proper directory, in my case it is + /driver/bus/pnp/devices/00:0f:: + + # cd /driver/bus/pnp/devices/00:0f + # cat name + PC standard floppy disk controller + +2. check if the device is already active:: + + # cat resources + DISABLED + + - Notice the string "DISABLED". This means the device is not active. + +3. check the device's possible configurations (optional):: + + # cat options + Dependent: 01 - Priority acceptable + port 0x3f0-0x3f0, align 0x7, size 0x6, 16-bit address decoding + port 0x3f7-0x3f7, align 0x0, size 0x1, 16-bit address decoding + irq 6 + dma 2 8-bit compatible + Dependent: 02 - Priority acceptable + port 0x370-0x370, align 0x7, size 0x6, 16-bit address decoding + port 0x377-0x377, align 0x0, size 0x1, 16-bit address decoding + irq 6 + dma 2 8-bit compatible + +4. now activate the device:: + + # echo "auto" > resources + +5. finally check if the device is active:: + + # cat resources + io 0x3f0-0x3f5 + io 0x3f7-0x3f7 + irq 6 + dma 2 + +also there are a series of kernel parameters:: + + pnp_reserve_irq=irq1[,irq2] .... + pnp_reserve_dma=dma1[,dma2] .... + pnp_reserve_io=io1,size1[,io2,size2] .... + pnp_reserve_mem=mem1,size1[,mem2,size2] .... The Unified Plug and Play Layer ------------------------------- - All Plug and Play drivers, protocols, and services meet at a central location + +All Plug and Play drivers, protocols, and services meet at a central location called the Plug and Play Layer. This layer is responsible for the exchange of information between PnP drivers and PnP protocols. Thus it automatically forwards commands to the proper protocol. This makes writing PnP drivers @@ -101,64 +121,73 @@ significantly easier. The following functions are available from the Plug and Play Layer: pnp_get_protocol -- increments the number of uses by one + increments the number of uses by one pnp_put_protocol -- deincrements the number of uses by one + deincrements the number of uses by one pnp_register_protocol -- use this to register a new PnP protocol + use this to register a new PnP protocol pnp_unregister_protocol -- use this function to remove a PnP protocol from the Plug and Play Layer + use this function to remove a PnP protocol from the Plug and Play Layer pnp_register_driver -- adds a PnP driver to the Plug and Play Layer -- this includes driver model integration -- returns zero for success or a negative error number for failure; count + adds a PnP driver to the Plug and Play Layer + + this includes driver model integration + returns zero for success or a negative error number for failure; count calls to the .add() method if you need to know how many devices bind to the driver pnp_unregister_driver -- removes a PnP driver from the Plug and Play Layer + removes a PnP driver from the Plug and Play Layer Plug and Play Protocols ----------------------- - This section contains information for PnP protocol developers. + +This section contains information for PnP protocol developers. The following Protocols are currently available in the computing world: -- PNPBIOS: used for system devices such as serial and parallel ports. -- ISAPNP: provides PnP support for the ISA bus -- ACPI: among its many uses, ACPI provides information about system level -devices. + +- PNPBIOS: + used for system devices such as serial and parallel ports. +- ISAPNP: + provides PnP support for the ISA bus +- ACPI: + among its many uses, ACPI provides information about system level + devices. + It is meant to replace the PNPBIOS. It is not currently supported by Linux Plug and Play but it is planned to be in the near future. Requirements for a Linux PnP protocol: -1.) the protocol must use EISA IDs -2.) the protocol must inform the PnP Layer of a device's current configuration +1. the protocol must use EISA IDs +2. the protocol must inform the PnP Layer of a device's current configuration + - the ability to set resources is optional but preferred. The following are PnP protocol related functions: pnp_add_device -- use this function to add a PnP device to the PnP layer -- only call this function when all wanted values are set in the pnp_dev -structure + use this function to add a PnP device to the PnP layer + + only call this function when all wanted values are set in the pnp_dev + structure pnp_init_device -- call this to initialize the PnP structure + call this to initialize the PnP structure pnp_remove_device -- call this to remove a device from the Plug and Play Layer. -- it will fail if the device is still in use. -- automatically will free mem used by the device and related structures + call this to remove a device from the Plug and Play Layer. + it will fail if the device is still in use. + automatically will free mem used by the device and related structures pnp_add_id -- adds an EISA ID to the list of supported IDs for the specified device + adds an EISA ID to the list of supported IDs for the specified device For more information consult the source of a protocol such as /drivers/pnp/pnpbios/core.c. @@ -167,85 +196,97 @@ For more information consult the source of a protocol such as Linux Plug and Play Drivers --------------------------- - This section contains information for Linux PnP driver developers. + +This section contains information for Linux PnP driver developers. The New Way -........... -1.) first make a list of supported EISA IDS -ex: -static const struct pnp_id pnp_dev_table[] = { - /* Standard LPT Printer Port */ - {.id = "PNP0400", .driver_data = 0}, - /* ECP Printer Port */ - {.id = "PNP0401", .driver_data = 0}, - {.id = ""} -}; - -Please note that the character 'X' can be used as a wild card in the function -portion (last four characters). -ex: +^^^^^^^^^^^ + +1. first make a list of supported EISA IDS + + ex:: + + static const struct pnp_id pnp_dev_table[] = { + /* Standard LPT Printer Port */ + {.id = "PNP0400", .driver_data = 0}, + /* ECP Printer Port */ + {.id = "PNP0401", .driver_data = 0}, + {.id = ""} + }; + + Please note that the character 'X' can be used as a wild card in the function + portion (last four characters). + + ex:: + /* Unknown PnP modems */ { "PNPCXXX", UNKNOWN_DEV }, -Supported PnP card IDs can optionally be defined. -ex: -static const struct pnp_id pnp_card_table[] = { - { "ANYDEVS", 0 }, - { "", 0 } -}; - -2.) Optionally define probe and remove functions. It may make sense not to -define these functions if the driver already has a reliable method of detecting -the resources, such as the parport_pc driver. -ex: -static int -serial_pnp_probe(struct pnp_dev * dev, const struct pnp_id *card_id, const - struct pnp_id *dev_id) -{ -. . . - -ex: -static void serial_pnp_remove(struct pnp_dev * dev) -{ -. . . - -consult /drivers/serial/8250_pnp.c for more information. - -3.) create a driver structure -ex: - -static struct pnp_driver serial_pnp_driver = { - .name = "serial", - .card_id_table = pnp_card_table, - .id_table = pnp_dev_table, - .probe = serial_pnp_probe, - .remove = serial_pnp_remove, -}; - -* name and id_table cannot be NULL. - -4.) register the driver -ex: - -static int __init serial8250_pnp_init(void) -{ - return pnp_register_driver(&serial_pnp_driver); -} + Supported PnP card IDs can optionally be defined. + ex:: + + static const struct pnp_id pnp_card_table[] = { + { "ANYDEVS", 0 }, + { "", 0 } + }; + +2. Optionally define probe and remove functions. It may make sense not to + define these functions if the driver already has a reliable method of detecting + the resources, such as the parport_pc driver. + + ex:: + + static int + serial_pnp_probe(struct pnp_dev * dev, const struct pnp_id *card_id, const + struct pnp_id *dev_id) + { + . . . + + ex:: + + static void serial_pnp_remove(struct pnp_dev * dev) + { + . . . + + consult /drivers/serial/8250_pnp.c for more information. + +3. create a driver structure + + ex:: + + static struct pnp_driver serial_pnp_driver = { + .name = "serial", + .card_id_table = pnp_card_table, + .id_table = pnp_dev_table, + .probe = serial_pnp_probe, + .remove = serial_pnp_remove, + }; + + * name and id_table cannot be NULL. + +4. register the driver + + ex:: + + static int __init serial8250_pnp_init(void) + { + return pnp_register_driver(&serial_pnp_driver); + } The Old Way -........... +^^^^^^^^^^^ A series of compatibility functions have been created to make it easy to convert ISAPNP drivers. They should serve as a temporary solution only. -They are as follows: +They are as follows:: -struct pnp_card *pnp_find_card(unsigned short vendor, - unsigned short device, - struct pnp_card *from) + struct pnp_card *pnp_find_card(unsigned short vendor, + unsigned short device, + struct pnp_card *from) -struct pnp_dev *pnp_find_dev(struct pnp_card *card, - unsigned short vendor, - unsigned short function, - struct pnp_dev *from) + struct pnp_dev *pnp_find_dev(struct pnp_card *card, + unsigned short vendor, + unsigned short function, + struct pnp_dev *from) diff --git a/Documentation/preempt-locking.txt b/Documentation/preempt-locking.txt index e89ce6624af2..c945062be66c 100644 --- a/Documentation/preempt-locking.txt +++ b/Documentation/preempt-locking.txt @@ -1,10 +1,13 @@ - Proper Locking Under a Preemptible Kernel: - Keeping Kernel Code Preempt-Safe - Robert Love <rml@tech9.net> - Last Updated: 28 Aug 2002 +=========================================================================== +Proper Locking Under a Preemptible Kernel: Keeping Kernel Code Preempt-Safe +=========================================================================== +:Author: Robert Love <rml@tech9.net> +:Last Updated: 28 Aug 2002 -INTRODUCTION + +Introduction +============ A preemptible kernel creates new locking issues. The issues are the same as @@ -17,9 +20,10 @@ requires protecting these situations. RULE #1: Per-CPU data structures need explicit protection +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ -Two similar problems arise. An example code snippet: +Two similar problems arise. An example code snippet:: struct this_needs_locking tux[NR_CPUS]; tux[smp_processor_id()] = some_value; @@ -35,6 +39,7 @@ You can also use put_cpu() and get_cpu(), which will disable preemption. RULE #2: CPU state must be protected. +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Under preemption, the state of the CPU must be protected. This is arch- @@ -52,6 +57,7 @@ However, fpu__restore() must be called with preemption disabled. RULE #3: Lock acquire and release must be performed by same task +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ A lock acquired in one task must be released by the same task. This @@ -61,17 +67,20 @@ like this, acquire and release the task in the same code path and have the caller wait on an event by the other task. -SOLUTION +Solution +======== Data protection under preemption is achieved by disabling preemption for the duration of the critical region. -preempt_enable() decrement the preempt counter -preempt_disable() increment the preempt counter -preempt_enable_no_resched() decrement, but do not immediately preempt -preempt_check_resched() if needed, reschedule -preempt_count() return the preempt counter +:: + + preempt_enable() decrement the preempt counter + preempt_disable() increment the preempt counter + preempt_enable_no_resched() decrement, but do not immediately preempt + preempt_check_resched() if needed, reschedule + preempt_count() return the preempt counter The functions are nestable. In other words, you can call preempt_disable n-times in a code path, and preemption will not be reenabled until the n-th @@ -89,7 +98,7 @@ So use this implicit preemption-disabling property only if you know that the affected codepath does not do any of this. Best policy is to use this only for small, atomic code that you wrote and which calls no complex functions. -Example: +Example:: cpucache_t *cc; /* this is per-CPU */ preempt_disable(); @@ -102,7 +111,7 @@ Example: return 0; Notice how the preemption statements must encompass every reference of the -critical variables. Another example: +critical variables. Another example:: int buf[NR_CPUS]; set_cpu_val(buf); @@ -114,7 +123,8 @@ This code is not preempt-safe, but see how easily we can fix it by simply moving the spin_lock up two lines. -PREVENTING PREEMPTION USING INTERRUPT DISABLING +Preventing preemption using interrupt disabling +=============================================== It is possible to prevent a preemption event using local_irq_disable and diff --git a/Documentation/printk-formats.txt b/Documentation/printk-formats.txt index 619cdffa5d44..65ea5915178b 100644 --- a/Documentation/printk-formats.txt +++ b/Documentation/printk-formats.txt @@ -1,5 +1,18 @@ -If variable is of Type, use printk format specifier: ---------------------------------------------------------- +========================================= +How to get printk format specifiers right +========================================= + +:Author: Randy Dunlap <rdunlap@infradead.org> +:Author: Andrew Murray <amurray@mpc-data.co.uk> + + +Integer types +============= + +:: + + If variable is of Type, use printk format specifier: + ------------------------------------------------------------ int %d or %x unsigned int %u or %x long %ld or %lx @@ -13,25 +26,29 @@ If variable is of Type, use printk format specifier: s64 %lld or %llx u64 %llu or %llx -If <type> is dependent on a config option for its size (e.g., sector_t, -blkcnt_t) or is architecture-dependent for its size (e.g., tcflag_t), use a -format specifier of its largest possible type and explicitly cast to it. -Example: +If <type> is dependent on a config option for its size (e.g., ``sector_t``, +``blkcnt_t``) or is architecture-dependent for its size (e.g., ``tcflag_t``), +use a format specifier of its largest possible type and explicitly cast to it. + +Example:: printk("test: sector number/total blocks: %llu/%llu\n", (unsigned long long)sector, (unsigned long long)blockcount); -Reminder: sizeof() result is of type size_t. +Reminder: ``sizeof()`` result is of type ``size_t``. -The kernel's printf does not support %n. For obvious reasons, floating -point formats (%e, %f, %g, %a) are also not recognized. Use of any +The kernel's printf does not support ``%n``. For obvious reasons, floating +point formats (``%e, %f, %g, %a``) are also not recognized. Use of any unsupported specifier or length qualifier results in a WARN and early return from vsnprintf. Raw pointer value SHOULD be printed with %p. The kernel supports the following extended format specifiers for pointer types: -Symbols/Function Pointers: +Symbols/Function Pointers +========================= + +:: %pF versatile_init+0x0/0x110 %pf versatile_init @@ -41,99 +58,122 @@ Symbols/Function Pointers: %ps versatile_init %pB prev_fn_of_versatile_init+0x88/0x88 - For printing symbols and function pointers. The 'S' and 's' specifiers - result in the symbol name with ('S') or without ('s') offsets. Where - this is used on a kernel without KALLSYMS - the symbol address is - printed instead. +For printing symbols and function pointers. The ``S`` and ``s`` specifiers +result in the symbol name with (``S``) or without (``s``) offsets. Where +this is used on a kernel without KALLSYMS - the symbol address is +printed instead. + +The ``B`` specifier results in the symbol name with offsets and should be +used when printing stack backtraces. The specifier takes into +consideration the effect of compiler optimisations which may occur +when tail-call``s are used and marked with the noreturn GCC attribute. - The 'B' specifier results in the symbol name with offsets and should be - used when printing stack backtraces. The specifier takes into - consideration the effect of compiler optimisations which may occur - when tail-call's are used and marked with the noreturn GCC attribute. +On ia64, ppc64 and parisc64 architectures function pointers are +actually function descriptors which must first be resolved. The ``F`` and +``f`` specifiers perform this resolution and then provide the same +functionality as the ``S`` and ``s`` specifiers. - On ia64, ppc64 and parisc64 architectures function pointers are - actually function descriptors which must first be resolved. The 'F' and - 'f' specifiers perform this resolution and then provide the same - functionality as the 'S' and 's' specifiers. +Kernel Pointers +=============== -Kernel Pointers: +:: %pK 0x01234567 or 0x0123456789abcdef - For printing kernel pointers which should be hidden from unprivileged - users. The behaviour of %pK depends on the kptr_restrict sysctl - see - Documentation/sysctl/kernel.txt for more details. +For printing kernel pointers which should be hidden from unprivileged +users. The behaviour of ``%pK`` depends on the ``kptr_restrict sysctl`` - see +Documentation/sysctl/kernel.txt for more details. + +Struct Resources +================ -Struct Resources: +:: %pr [mem 0x60000000-0x6fffffff flags 0x2200] or [mem 0x0000000060000000-0x000000006fffffff flags 0x2200] %pR [mem 0x60000000-0x6fffffff pref] or [mem 0x0000000060000000-0x000000006fffffff pref] - For printing struct resources. The 'R' and 'r' specifiers result in a - printed resource with ('R') or without ('r') a decoded flags member. - Passed by reference. +For printing struct resources. The ``R`` and ``r`` specifiers result in a +printed resource with (``R``) or without (``r``) a decoded flags member. +Passed by reference. + +Physical addresses types ``phys_addr_t`` +======================================== -Physical addresses types phys_addr_t: +:: %pa[p] 0x01234567 or 0x0123456789abcdef - For printing a phys_addr_t type (and its derivatives, such as - resource_size_t) which can vary based on build options, regardless of - the width of the CPU data path. Passed by reference. +For printing a ``phys_addr_t`` type (and its derivatives, such as +``resource_size_t``) which can vary based on build options, regardless of +the width of the CPU data path. Passed by reference. -DMA addresses types dma_addr_t: +DMA addresses types ``dma_addr_t`` +================================== + +:: %pad 0x01234567 or 0x0123456789abcdef - For printing a dma_addr_t type which can vary based on build options, - regardless of the width of the CPU data path. Passed by reference. +For printing a ``dma_addr_t`` type which can vary based on build options, +regardless of the width of the CPU data path. Passed by reference. + +Raw buffer as an escaped string +=============================== -Raw buffer as an escaped string: +:: %*pE[achnops] - For printing raw buffer as an escaped string. For the following buffer +For printing raw buffer as an escaped string. For the following buffer:: 1b 62 20 5c 43 07 22 90 0d 5d - few examples show how the conversion would be done (the result string - without surrounding quotes): +few examples show how the conversion would be done (the result string +without surrounding quotes):: %*pE "\eb \C\a"\220\r]" %*pEhp "\x1bb \C\x07"\x90\x0d]" %*pEa "\e\142\040\\\103\a\042\220\r\135" - The conversion rules are applied according to an optional combination - of flags (see string_escape_mem() kernel documentation for the - details): - a - ESCAPE_ANY - c - ESCAPE_SPECIAL - h - ESCAPE_HEX - n - ESCAPE_NULL - o - ESCAPE_OCTAL - p - ESCAPE_NP - s - ESCAPE_SPACE - By default ESCAPE_ANY_NP is used. +The conversion rules are applied according to an optional combination +of flags (see :c:func:`string_escape_mem` kernel documentation for the +details): + + - ``a`` - ESCAPE_ANY + - ``c`` - ESCAPE_SPECIAL + - ``h`` - ESCAPE_HEX + - ``n`` - ESCAPE_NULL + - ``o`` - ESCAPE_OCTAL + - ``p`` - ESCAPE_NP + - ``s`` - ESCAPE_SPACE - ESCAPE_ANY_NP is the sane choice for many cases, in particularly for - printing SSIDs. +By default ESCAPE_ANY_NP is used. - If field width is omitted the 1 byte only will be escaped. +ESCAPE_ANY_NP is the sane choice for many cases, in particularly for +printing SSIDs. -Raw buffer as a hex string: +If field width is omitted the 1 byte only will be escaped. + +Raw buffer as a hex string +========================== + +:: %*ph 00 01 02 ... 3f %*phC 00:01:02: ... :3f %*phD 00-01-02- ... -3f %*phN 000102 ... 3f - For printing a small buffers (up to 64 bytes long) as a hex string with - certain separator. For the larger buffers consider to use - print_hex_dump(). +For printing a small buffers (up to 64 bytes long) as a hex string with +certain separator. For the larger buffers consider to use +:c:func:`print_hex_dump`. + +MAC/FDDI addresses +================== -MAC/FDDI addresses: +:: %pM 00:01:02:03:04:05 %pMR 05:04:03:02:01:00 @@ -141,53 +181,62 @@ MAC/FDDI addresses: %pm 000102030405 %pmR 050403020100 - For printing 6-byte MAC/FDDI addresses in hex notation. The 'M' and 'm' - specifiers result in a printed address with ('M') or without ('m') byte - separators. The default byte separator is the colon (':'). +For printing 6-byte MAC/FDDI addresses in hex notation. The ``M`` and ``m`` +specifiers result in a printed address with (``M``) or without (``m``) byte +separators. The default byte separator is the colon (``:``). - Where FDDI addresses are concerned the 'F' specifier can be used after - the 'M' specifier to use dash ('-') separators instead of the default - separator. +Where FDDI addresses are concerned the ``F`` specifier can be used after +the ``M`` specifier to use dash (``-``) separators instead of the default +separator. - For Bluetooth addresses the 'R' specifier shall be used after the 'M' - specifier to use reversed byte order suitable for visual interpretation - of Bluetooth addresses which are in the little endian order. +For Bluetooth addresses the ``R`` specifier shall be used after the ``M`` +specifier to use reversed byte order suitable for visual interpretation +of Bluetooth addresses which are in the little endian order. - Passed by reference. +Passed by reference. + +IPv4 addresses +============== -IPv4 addresses: +:: %pI4 1.2.3.4 %pi4 001.002.003.004 %p[Ii]4[hnbl] - For printing IPv4 dot-separated decimal addresses. The 'I4' and 'i4' - specifiers result in a printed address with ('i4') or without ('I4') - leading zeros. +For printing IPv4 dot-separated decimal addresses. The ``I4`` and ``i4`` +specifiers result in a printed address with (``i4``) or without (``I4``) +leading zeros. - The additional 'h', 'n', 'b', and 'l' specifiers are used to specify - host, network, big or little endian order addresses respectively. Where - no specifier is provided the default network/big endian order is used. +The additional ``h``, ``n``, ``b``, and ``l`` specifiers are used to specify +host, network, big or little endian order addresses respectively. Where +no specifier is provided the default network/big endian order is used. - Passed by reference. +Passed by reference. -IPv6 addresses: +IPv6 addresses +============== + +:: %pI6 0001:0002:0003:0004:0005:0006:0007:0008 %pi6 00010002000300040005000600070008 %pI6c 1:2:3:4:5:6:7:8 - For printing IPv6 network-order 16-bit hex addresses. The 'I6' and 'i6' - specifiers result in a printed address with ('I6') or without ('i6') - colon-separators. Leading zeros are always used. +For printing IPv6 network-order 16-bit hex addresses. The ``I6`` and ``i6`` +specifiers result in a printed address with (``I6``) or without (``i6``) +colon-separators. Leading zeros are always used. - The additional 'c' specifier can be used with the 'I' specifier to - print a compressed IPv6 address as described by - http://tools.ietf.org/html/rfc5952 +The additional ``c`` specifier can be used with the ``I`` specifier to +print a compressed IPv6 address as described by +http://tools.ietf.org/html/rfc5952 - Passed by reference. +Passed by reference. -IPv4/IPv6 addresses (generic, with port, flowinfo, scope): +IPv4/IPv6 addresses (generic, with port, flowinfo, scope) +========================================================= + +:: %pIS 1.2.3.4 or 0001:0002:0003:0004:0005:0006:0007:0008 %piS 001.002.003.004 or 00010002000300040005000600070008 @@ -195,87 +244,103 @@ IPv4/IPv6 addresses (generic, with port, flowinfo, scope): %pISpc 1.2.3.4:12345 or [1:2:3:4:5:6:7:8]:12345 %p[Ii]S[pfschnbl] - For printing an IP address without the need to distinguish whether it's - of type AF_INET or AF_INET6, a pointer to a valid 'struct sockaddr', - specified through 'IS' or 'iS', can be passed to this format specifier. +For printing an IP address without the need to distinguish whether it``s +of type AF_INET or AF_INET6, a pointer to a valid ``struct sockaddr``, +specified through ``IS`` or ``iS``, can be passed to this format specifier. - The additional 'p', 'f', and 's' specifiers are used to specify port - (IPv4, IPv6), flowinfo (IPv6) and scope (IPv6). Ports have a ':' prefix, - flowinfo a '/' and scope a '%', each followed by the actual value. +The additional ``p``, ``f``, and ``s`` specifiers are used to specify port +(IPv4, IPv6), flowinfo (IPv6) and scope (IPv6). Ports have a ``:`` prefix, +flowinfo a ``/`` and scope a ``%``, each followed by the actual value. - In case of an IPv6 address the compressed IPv6 address as described by - http://tools.ietf.org/html/rfc5952 is being used if the additional - specifier 'c' is given. The IPv6 address is surrounded by '[', ']' in - case of additional specifiers 'p', 'f' or 's' as suggested by - https://tools.ietf.org/html/draft-ietf-6man-text-addr-representation-07 +In case of an IPv6 address the compressed IPv6 address as described by +http://tools.ietf.org/html/rfc5952 is being used if the additional +specifier ``c`` is given. The IPv6 address is surrounded by ``[``, ``]`` in +case of additional specifiers ``p``, ``f`` or ``s`` as suggested by +https://tools.ietf.org/html/draft-ietf-6man-text-addr-representation-07 - In case of IPv4 addresses, the additional 'h', 'n', 'b', and 'l' - specifiers can be used as well and are ignored in case of an IPv6 - address. +In case of IPv4 addresses, the additional ``h``, ``n``, ``b``, and ``l`` +specifiers can be used as well and are ignored in case of an IPv6 +address. - Passed by reference. +Passed by reference. - Further examples: +Further examples:: %pISfc 1.2.3.4 or [1:2:3:4:5:6:7:8]/123456789 %pISsc 1.2.3.4 or [1:2:3:4:5:6:7:8]%1234567890 %pISpfc 1.2.3.4:12345 or [1:2:3:4:5:6:7:8]:12345/123456789 -UUID/GUID addresses: +UUID/GUID addresses +=================== + +:: %pUb 00010203-0405-0607-0809-0a0b0c0d0e0f %pUB 00010203-0405-0607-0809-0A0B0C0D0E0F %pUl 03020100-0504-0706-0809-0a0b0c0e0e0f %pUL 03020100-0504-0706-0809-0A0B0C0E0E0F - For printing 16-byte UUID/GUIDs addresses. The additional 'l', 'L', - 'b' and 'B' specifiers are used to specify a little endian order in - lower ('l') or upper case ('L') hex characters - and big endian order - in lower ('b') or upper case ('B') hex characters. +For printing 16-byte UUID/GUIDs addresses. The additional 'l', 'L', +'b' and 'B' specifiers are used to specify a little endian order in +lower ('l') or upper case ('L') hex characters - and big endian order +in lower ('b') or upper case ('B') hex characters. - Where no additional specifiers are used the default big endian - order with lower case hex characters will be printed. +Where no additional specifiers are used the default big endian +order with lower case hex characters will be printed. - Passed by reference. +Passed by reference. + +dentry names +============ -dentry names: +:: %pd{,2,3,4} %pD{,2,3,4} - For printing dentry name; if we race with d_move(), the name might be - a mix of old and new ones, but it won't oops. %pd dentry is a safer - equivalent of %s dentry->d_name.name we used to use, %pd<n> prints - n last components. %pD does the same thing for struct file. +For printing dentry name; if we race with :c:func:`d_move`, the name might be +a mix of old and new ones, but it won't oops. ``%pd`` dentry is a safer +equivalent of ``%s`` ``dentry->d_name.name`` we used to use, ``%pd<n>`` prints +``n`` last components. ``%pD`` does the same thing for struct file. - Passed by reference. +Passed by reference. -block_device names: +block_device names +================== + +:: %pg sda, sda1 or loop0p1 - For printing name of block_device pointers. +For printing name of block_device pointers. + +struct va_format +================ -struct va_format: +:: %pV - For printing struct va_format structures. These contain a format string - and va_list as follows: +For printing struct va_format structures. These contain a format string +and va_list as follows:: struct va_format { const char *fmt; va_list *va; }; - Implements a "recursive vsnprintf". +Implements a "recursive vsnprintf". - Do not use this feature without some mechanism to verify the - correctness of the format string and va_list arguments. +Do not use this feature without some mechanism to verify the +correctness of the format string and va_list arguments. - Passed by reference. +Passed by reference. + +kobjects +======== + +:: -kobjects: %pO Base specifier for kobject based structs. Must be followed with @@ -311,61 +376,70 @@ kobjects: Passed by reference. -struct clk: + +struct clk +========== + +:: %pC pll1 %pCn pll1 %pCr 1560000000 - For printing struct clk structures. '%pC' and '%pCn' print the name - (Common Clock Framework) or address (legacy clock framework) of the - structure; '%pCr' prints the current clock rate. +For printing struct clk structures. ``%pC`` and ``%pCn`` print the name +(Common Clock Framework) or address (legacy clock framework) of the +structure; ``%pCr`` prints the current clock rate. - Passed by reference. +Passed by reference. -bitmap and its derivatives such as cpumask and nodemask: +bitmap and its derivatives such as cpumask and nodemask +======================================================= + +:: %*pb 0779 %*pbl 0,3-6,8-10 - For printing bitmap and its derivatives such as cpumask and nodemask, - %*pb output the bitmap with field width as the number of bits and %*pbl - output the bitmap as range list with field width as the number of bits. +For printing bitmap and its derivatives such as cpumask and nodemask, +``%*pb`` output the bitmap with field width as the number of bits and ``%*pbl`` +output the bitmap as range list with field width as the number of bits. - Passed by reference. +Passed by reference. + +Flags bitfields such as page flags, gfp_flags +============================================= -Flags bitfields such as page flags, gfp_flags: +:: %pGp referenced|uptodate|lru|active|private %pGg GFP_USER|GFP_DMA32|GFP_NOWARN %pGv read|exec|mayread|maywrite|mayexec|denywrite - For printing flags bitfields as a collection of symbolic constants that - would construct the value. The type of flags is given by the third - character. Currently supported are [p]age flags, [v]ma_flags (both - expect unsigned long *) and [g]fp_flags (expects gfp_t *). The flag - names and print order depends on the particular type. +For printing flags bitfields as a collection of symbolic constants that +would construct the value. The type of flags is given by the third +character. Currently supported are [p]age flags, [v]ma_flags (both +expect ``unsigned long *``) and [g]fp_flags (expects ``gfp_t *``). The flag +names and print order depends on the particular type. - Note that this format should not be used directly in TP_printk() part - of a tracepoint. Instead, use the show_*_flags() functions from - <trace/events/mmflags.h>. +Note that this format should not be used directly in :c:func:`TP_printk()` part +of a tracepoint. Instead, use the ``show_*_flags()`` functions from +<trace/events/mmflags.h>. - Passed by reference. +Passed by reference. + +Network device features +======================= -Network device features: +:: %pNF 0x000000000000c000 - For printing netdev_features_t. +For printing netdev_features_t. - Passed by reference. +Passed by reference. -If you add other %p extensions, please extend lib/test_printf.c with +If you add other ``%p`` extensions, please extend lib/test_printf.c with one or more test cases, if at all feasible. Thank you for your cooperation and attention. - - -By Randy Dunlap <rdunlap@infradead.org> and -Andrew Murray <amurray@mpc-data.co.uk> diff --git a/Documentation/pwm.txt b/Documentation/pwm.txt index 789b27c6ec99..8fbf0aa3ba2d 100644 --- a/Documentation/pwm.txt +++ b/Documentation/pwm.txt @@ -1,4 +1,6 @@ +====================================== Pulse Width Modulation (PWM) interface +====================================== This provides an overview about the Linux PWM interface @@ -16,7 +18,7 @@ Users of the legacy PWM API use unique IDs to refer to PWM devices. Instead of referring to a PWM device via its unique ID, board setup code should instead register a static mapping that can be used to match PWM -consumers to providers, as given in the following example: +consumers to providers, as given in the following example:: static struct pwm_lookup board_pwm_lookup[] = { PWM_LOOKUP("tegra-pwm", 0, "pwm-backlight", NULL, @@ -40,9 +42,9 @@ New users should use the pwm_get() function and pass to it the consumer device or a consumer name. pwm_put() is used to free the PWM device. Managed variants of these functions, devm_pwm_get() and devm_pwm_put(), also exist. -After being requested, a PWM has to be configured using: +After being requested, a PWM has to be configured using:: -int pwm_apply_state(struct pwm_device *pwm, struct pwm_state *state); + int pwm_apply_state(struct pwm_device *pwm, struct pwm_state *state); This API controls both the PWM period/duty_cycle config and the enable/disable state. @@ -72,11 +74,14 @@ interface is provided to use the PWMs from userspace. It is exposed at pwmchipN, where N is the base of the PWM chip. Inside the directory you will find: -npwm - The number of PWM channels this chip supports (read-only). + npwm + The number of PWM channels this chip supports (read-only). -export - Exports a PWM channel for use with sysfs (write-only). + export + Exports a PWM channel for use with sysfs (write-only). -unexport - Unexports a PWM channel from sysfs (write-only). + unexport + Unexports a PWM channel from sysfs (write-only). The PWM channels are numbered using a per-chip index from 0 to npwm-1. @@ -84,21 +89,26 @@ When a PWM channel is exported a pwmX directory will be created in the pwmchipN directory it is associated with, where X is the number of the channel that was exported. The following properties will then be available: -period - The total period of the PWM signal (read/write). - Value is in nanoseconds and is the sum of the active and inactive - time of the PWM. + period + The total period of the PWM signal (read/write). + Value is in nanoseconds and is the sum of the active and inactive + time of the PWM. -duty_cycle - The active time of the PWM signal (read/write). - Value is in nanoseconds and must be less than the period. + duty_cycle + The active time of the PWM signal (read/write). + Value is in nanoseconds and must be less than the period. -polarity - Changes the polarity of the PWM signal (read/write). - Writes to this property only work if the PWM chip supports changing - the polarity. The polarity can only be changed if the PWM is not - enabled. Value is the string "normal" or "inversed". + polarity + Changes the polarity of the PWM signal (read/write). + Writes to this property only work if the PWM chip supports changing + the polarity. The polarity can only be changed if the PWM is not + enabled. Value is the string "normal" or "inversed". -enable - Enable/disable the PWM signal (read/write). - 0 - disabled - 1 - enabled + enable + Enable/disable the PWM signal (read/write). + + - 0 - disabled + - 1 - enabled Implementing a PWM driver ------------------------- diff --git a/Documentation/rbtree.txt b/Documentation/rbtree.txt index b9d9cc57be18..b8a8c70b0188 100644 --- a/Documentation/rbtree.txt +++ b/Documentation/rbtree.txt @@ -1,7 +1,10 @@ +================================= Red-black Trees (rbtree) in Linux -January 18, 2007 -Rob Landley <rob@landley.net> -============================= +================================= + + +:Date: January 18, 2007 +:Author: Rob Landley <rob@landley.net> What are red-black trees, and what are they for? ------------------------------------------------ @@ -56,7 +59,7 @@ user of the rbtree code. Creating a new rbtree --------------------- -Data nodes in an rbtree tree are structures containing a struct rb_node member: +Data nodes in an rbtree tree are structures containing a struct rb_node member:: struct mytype { struct rb_node node; @@ -78,7 +81,7 @@ Searching for a value in an rbtree Writing a search function for your tree is fairly straightforward: start at the root, compare each value, and follow the left or right branch as necessary. -Example: +Example:: struct mytype *my_search(struct rb_root *root, char *string) { @@ -110,7 +113,7 @@ The search for insertion differs from the previous search by finding the location of the pointer on which to graft the new node. The new node also needs a link to its parent node for rebalancing purposes. -Example: +Example:: int my_insert(struct rb_root *root, struct mytype *data) { @@ -140,11 +143,11 @@ Example: Removing or replacing existing data in an rbtree ------------------------------------------------ -To remove an existing node from a tree, call: +To remove an existing node from a tree, call:: void rb_erase(struct rb_node *victim, struct rb_root *tree); -Example: +Example:: struct mytype *data = mysearch(&mytree, "walrus"); @@ -153,7 +156,7 @@ Example: myfree(data); } -To replace an existing node in a tree with a new one with the same key, call: +To replace an existing node in a tree with a new one with the same key, call:: void rb_replace_node(struct rb_node *old, struct rb_node *new, struct rb_root *tree); @@ -166,7 +169,7 @@ Iterating through the elements stored in an rbtree (in sort order) Four functions are provided for iterating through an rbtree's contents in sorted order. These work on arbitrary trees, and should not need to be -modified or wrapped (except for locking purposes): +modified or wrapped (except for locking purposes):: struct rb_node *rb_first(struct rb_root *tree); struct rb_node *rb_last(struct rb_root *tree); @@ -184,7 +187,7 @@ which the containing data structure may be accessed with the container_of() macro, and individual members may be accessed directly via rb_entry(node, type, member). -Example: +Example:: struct rb_node *node; for (node = rb_first(&mytree); node; node = rb_next(node)) @@ -241,7 +244,8 @@ user should have a single rb_erase_augmented() call site in order to limit compiled code size. -Sample usage: +Sample usage +^^^^^^^^^^^^ Interval tree is an example of augmented rb tree. Reference - "Introduction to Algorithms" by Cormen, Leiserson, Rivest and Stein. @@ -259,12 +263,12 @@ This "extra information" stored in each node is the maximum hi information can be maintained at each node just be looking at the node and its immediate children. And this will be used in O(log n) lookup for lowest match (lowest start address among all possible matches) -with something like: +with something like:: -struct interval_tree_node * -interval_tree_first_match(struct rb_root *root, - unsigned long start, unsigned long last) -{ + struct interval_tree_node * + interval_tree_first_match(struct rb_root *root, + unsigned long start, unsigned long last) + { struct interval_tree_node *node; if (!root->rb_node) @@ -301,13 +305,13 @@ interval_tree_first_match(struct rb_root *root, } return NULL; /* No match */ } -} + } -Insertion/removal are defined using the following augmented callbacks: +Insertion/removal are defined using the following augmented callbacks:: -static inline unsigned long -compute_subtree_last(struct interval_tree_node *node) -{ + static inline unsigned long + compute_subtree_last(struct interval_tree_node *node) + { unsigned long max = node->last, subtree_last; if (node->rb.rb_left) { subtree_last = rb_entry(node->rb.rb_left, @@ -322,10 +326,10 @@ compute_subtree_last(struct interval_tree_node *node) max = subtree_last; } return max; -} + } -static void augment_propagate(struct rb_node *rb, struct rb_node *stop) -{ + static void augment_propagate(struct rb_node *rb, struct rb_node *stop) + { while (rb != stop) { struct interval_tree_node *node = rb_entry(rb, struct interval_tree_node, rb); @@ -335,20 +339,20 @@ static void augment_propagate(struct rb_node *rb, struct rb_node *stop) node->__subtree_last = subtree_last; rb = rb_parent(&node->rb); } -} + } -static void augment_copy(struct rb_node *rb_old, struct rb_node *rb_new) -{ + static void augment_copy(struct rb_node *rb_old, struct rb_node *rb_new) + { struct interval_tree_node *old = rb_entry(rb_old, struct interval_tree_node, rb); struct interval_tree_node *new = rb_entry(rb_new, struct interval_tree_node, rb); new->__subtree_last = old->__subtree_last; -} + } -static void augment_rotate(struct rb_node *rb_old, struct rb_node *rb_new) -{ + static void augment_rotate(struct rb_node *rb_old, struct rb_node *rb_new) + { struct interval_tree_node *old = rb_entry(rb_old, struct interval_tree_node, rb); struct interval_tree_node *new = @@ -356,15 +360,15 @@ static void augment_rotate(struct rb_node *rb_old, struct rb_node *rb_new) new->__subtree_last = old->__subtree_last; old->__subtree_last = compute_subtree_last(old); -} + } -static const struct rb_augment_callbacks augment_callbacks = { + static const struct rb_augment_callbacks augment_callbacks = { augment_propagate, augment_copy, augment_rotate -}; + }; -void interval_tree_insert(struct interval_tree_node *node, - struct rb_root *root) -{ + void interval_tree_insert(struct interval_tree_node *node, + struct rb_root *root) + { struct rb_node **link = &root->rb_node, *rb_parent = NULL; unsigned long start = node->start, last = node->last; struct interval_tree_node *parent; @@ -383,10 +387,10 @@ void interval_tree_insert(struct interval_tree_node *node, node->__subtree_last = last; rb_link_node(&node->rb, rb_parent, link); rb_insert_augmented(&node->rb, root, &augment_callbacks); -} + } -void interval_tree_remove(struct interval_tree_node *node, - struct rb_root *root) -{ + void interval_tree_remove(struct interval_tree_node *node, + struct rb_root *root) + { rb_erase_augmented(&node->rb, root, &augment_callbacks); -} + } diff --git a/Documentation/remoteproc.txt b/Documentation/remoteproc.txt index f07597482351..77fb03acdbb4 100644 --- a/Documentation/remoteproc.txt +++ b/Documentation/remoteproc.txt @@ -1,6 +1,9 @@ +========================== Remote Processor Framework +========================== -1. Introduction +Introduction +============ Modern SoCs typically have heterogeneous remote processor devices in asymmetric multiprocessing (AMP) configurations, which may be running different instances @@ -26,44 +29,62 @@ remoteproc will add those devices. This makes it possible to reuse the existing virtio drivers with remote processor backends at a minimal development cost. -2. User API +User API +======== + +:: int rproc_boot(struct rproc *rproc) - - Boot a remote processor (i.e. load its firmware, power it on, ...). - If the remote processor is already powered on, this function immediately - returns (successfully). - Returns 0 on success, and an appropriate error value otherwise. - Note: to use this function you should already have a valid rproc - handle. There are several ways to achieve that cleanly (devres, pdata, - the way remoteproc_rpmsg.c does this, or, if this becomes prevalent, we - might also consider using dev_archdata for this). + +Boot a remote processor (i.e. load its firmware, power it on, ...). + +If the remote processor is already powered on, this function immediately +returns (successfully). + +Returns 0 on success, and an appropriate error value otherwise. +Note: to use this function you should already have a valid rproc +handle. There are several ways to achieve that cleanly (devres, pdata, +the way remoteproc_rpmsg.c does this, or, if this becomes prevalent, we +might also consider using dev_archdata for this). + +:: void rproc_shutdown(struct rproc *rproc) - - Power off a remote processor (previously booted with rproc_boot()). - In case @rproc is still being used by an additional user(s), then - this function will just decrement the power refcount and exit, - without really powering off the device. - Every call to rproc_boot() must (eventually) be accompanied by a call - to rproc_shutdown(). Calling rproc_shutdown() redundantly is a bug. - Notes: - - we're not decrementing the rproc's refcount, only the power refcount. - which means that the @rproc handle stays valid even after - rproc_shutdown() returns, and users can still use it with a subsequent - rproc_boot(), if needed. + +Power off a remote processor (previously booted with rproc_boot()). +In case @rproc is still being used by an additional user(s), then +this function will just decrement the power refcount and exit, +without really powering off the device. + +Every call to rproc_boot() must (eventually) be accompanied by a call +to rproc_shutdown(). Calling rproc_shutdown() redundantly is a bug. + +.. note:: + + we're not decrementing the rproc's refcount, only the power refcount. + which means that the @rproc handle stays valid even after + rproc_shutdown() returns, and users can still use it with a subsequent + rproc_boot(), if needed. + +:: struct rproc *rproc_get_by_phandle(phandle phandle) - - Find an rproc handle using a device tree phandle. Returns the rproc - handle on success, and NULL on failure. This function increments - the remote processor's refcount, so always use rproc_put() to - decrement it back once rproc isn't needed anymore. -3. Typical usage +Find an rproc handle using a device tree phandle. Returns the rproc +handle on success, and NULL on failure. This function increments +the remote processor's refcount, so always use rproc_put() to +decrement it back once rproc isn't needed anymore. + +Typical usage +============= -#include <linux/remoteproc.h> +:: -/* in case we were given a valid 'rproc' handle */ -int dummy_rproc_example(struct rproc *my_rproc) -{ + #include <linux/remoteproc.h> + + /* in case we were given a valid 'rproc' handle */ + int dummy_rproc_example(struct rproc *my_rproc) + { int ret; /* let's power on and boot our remote processor */ @@ -80,84 +101,111 @@ int dummy_rproc_example(struct rproc *my_rproc) /* let's shut it down now */ rproc_shutdown(my_rproc); -} + } + +API for implementors +==================== -4. API for implementors +:: struct rproc *rproc_alloc(struct device *dev, const char *name, const struct rproc_ops *ops, const char *firmware, int len) - - Allocate a new remote processor handle, but don't register - it yet. Required parameters are the underlying device, the - name of this remote processor, platform-specific ops handlers, - the name of the firmware to boot this rproc with, and the - length of private data needed by the allocating rproc driver (in bytes). - - This function should be used by rproc implementations during - initialization of the remote processor. - After creating an rproc handle using this function, and when ready, - implementations should then call rproc_add() to complete - the registration of the remote processor. - On success, the new rproc is returned, and on failure, NULL. - - Note: _never_ directly deallocate @rproc, even if it was not registered - yet. Instead, when you need to unroll rproc_alloc(), use rproc_free(). + +Allocate a new remote processor handle, but don't register +it yet. Required parameters are the underlying device, the +name of this remote processor, platform-specific ops handlers, +the name of the firmware to boot this rproc with, and the +length of private data needed by the allocating rproc driver (in bytes). + +This function should be used by rproc implementations during +initialization of the remote processor. + +After creating an rproc handle using this function, and when ready, +implementations should then call rproc_add() to complete +the registration of the remote processor. + +On success, the new rproc is returned, and on failure, NULL. + +.. note:: + + **never** directly deallocate @rproc, even if it was not registered + yet. Instead, when you need to unroll rproc_alloc(), use rproc_free(). + +:: void rproc_free(struct rproc *rproc) - - Free an rproc handle that was allocated by rproc_alloc. - This function essentially unrolls rproc_alloc(), by decrementing the - rproc's refcount. It doesn't directly free rproc; that would happen - only if there are no other references to rproc and its refcount now - dropped to zero. + +Free an rproc handle that was allocated by rproc_alloc. + +This function essentially unrolls rproc_alloc(), by decrementing the +rproc's refcount. It doesn't directly free rproc; that would happen +only if there are no other references to rproc and its refcount now +dropped to zero. + +:: int rproc_add(struct rproc *rproc) - - Register @rproc with the remoteproc framework, after it has been - allocated with rproc_alloc(). - This is called by the platform-specific rproc implementation, whenever - a new remote processor device is probed. - Returns 0 on success and an appropriate error code otherwise. - Note: this function initiates an asynchronous firmware loading - context, which will look for virtio devices supported by the rproc's - firmware. - If found, those virtio devices will be created and added, so as a result - of registering this remote processor, additional virtio drivers might get - probed. + +Register @rproc with the remoteproc framework, after it has been +allocated with rproc_alloc(). + +This is called by the platform-specific rproc implementation, whenever +a new remote processor device is probed. + +Returns 0 on success and an appropriate error code otherwise. +Note: this function initiates an asynchronous firmware loading +context, which will look for virtio devices supported by the rproc's +firmware. + +If found, those virtio devices will be created and added, so as a result +of registering this remote processor, additional virtio drivers might get +probed. + +:: int rproc_del(struct rproc *rproc) - - Unroll rproc_add(). - This function should be called when the platform specific rproc - implementation decides to remove the rproc device. it should - _only_ be called if a previous invocation of rproc_add() - has completed successfully. - After rproc_del() returns, @rproc is still valid, and its - last refcount should be decremented by calling rproc_free(). +Unroll rproc_add(). + +This function should be called when the platform specific rproc +implementation decides to remove the rproc device. it should +_only_ be called if a previous invocation of rproc_add() +has completed successfully. - Returns 0 on success and -EINVAL if @rproc isn't valid. +After rproc_del() returns, @rproc is still valid, and its +last refcount should be decremented by calling rproc_free(). + +Returns 0 on success and -EINVAL if @rproc isn't valid. + +:: void rproc_report_crash(struct rproc *rproc, enum rproc_crash_type type) - - Report a crash in a remoteproc - This function must be called every time a crash is detected by the - platform specific rproc implementation. This should not be called from a - non-remoteproc driver. This function can be called from atomic/interrupt - context. -5. Implementation callbacks +Report a crash in a remoteproc + +This function must be called every time a crash is detected by the +platform specific rproc implementation. This should not be called from a +non-remoteproc driver. This function can be called from atomic/interrupt +context. + +Implementation callbacks +======================== These callbacks should be provided by platform-specific remoteproc -drivers: - -/** - * struct rproc_ops - platform-specific device handlers - * @start: power on the device and boot it - * @stop: power off the device - * @kick: kick a virtqueue (virtqueue id given as a parameter) - */ -struct rproc_ops { +drivers:: + + /** + * struct rproc_ops - platform-specific device handlers + * @start: power on the device and boot it + * @stop: power off the device + * @kick: kick a virtqueue (virtqueue id given as a parameter) + */ + struct rproc_ops { int (*start)(struct rproc *rproc); int (*stop)(struct rproc *rproc); void (*kick)(struct rproc *rproc, int vqid); -}; + }; Every remoteproc implementation should at least provide the ->start and ->stop handlers. If rpmsg/virtio functionality is also desired, then the ->kick handler @@ -179,7 +227,8 @@ the exact virtqueue index to look in is optional: it is easy (and not too expensive) to go through the existing virtqueues and look for new buffers in the used rings. -6. Binary Firmware Structure +Binary Firmware Structure +========================= At this point remoteproc only supports ELF32 firmware binaries. However, it is quite expected that other platforms/devices which we'd want to @@ -207,43 +256,43 @@ resource entries that publish the existence of supported features or configurations by the remote processor, such as trace buffers and supported virtio devices (and their configurations). -The resource table begins with this header: - -/** - * struct resource_table - firmware resource table header - * @ver: version number - * @num: number of resource entries - * @reserved: reserved (must be zero) - * @offset: array of offsets pointing at the various resource entries - * - * The header of the resource table, as expressed by this structure, - * contains a version number (should we need to change this format in the - * future), the number of available resource entries, and their offsets - * in the table. - */ -struct resource_table { +The resource table begins with this header:: + + /** + * struct resource_table - firmware resource table header + * @ver: version number + * @num: number of resource entries + * @reserved: reserved (must be zero) + * @offset: array of offsets pointing at the various resource entries + * + * The header of the resource table, as expressed by this structure, + * contains a version number (should we need to change this format in the + * future), the number of available resource entries, and their offsets + * in the table. + */ + struct resource_table { u32 ver; u32 num; u32 reserved[2]; u32 offset[0]; -} __packed; + } __packed; Immediately following this header are the resource entries themselves, -each of which begins with the following resource entry header: - -/** - * struct fw_rsc_hdr - firmware resource entry header - * @type: resource type - * @data: resource data - * - * Every resource entry begins with a 'struct fw_rsc_hdr' header providing - * its @type. The content of the entry itself will immediately follow - * this header, and it should be parsed according to the resource type. - */ -struct fw_rsc_hdr { +each of which begins with the following resource entry header:: + + /** + * struct fw_rsc_hdr - firmware resource entry header + * @type: resource type + * @data: resource data + * + * Every resource entry begins with a 'struct fw_rsc_hdr' header providing + * its @type. The content of the entry itself will immediately follow + * this header, and it should be parsed according to the resource type. + */ + struct fw_rsc_hdr { u32 type; u8 data[0]; -} __packed; + } __packed; Some resources entries are mere announcements, where the host is informed of specific remoteproc configuration. Other entries require the host to @@ -252,32 +301,32 @@ is expected, where the firmware requests a resource, and once allocated, the host should provide back its details (e.g. address of an allocated memory region). -Here are the various resource types that are currently supported: - -/** - * enum fw_resource_type - types of resource entries - * - * @RSC_CARVEOUT: request for allocation of a physically contiguous - * memory region. - * @RSC_DEVMEM: request to iommu_map a memory-based peripheral. - * @RSC_TRACE: announces the availability of a trace buffer into which - * the remote processor will be writing logs. - * @RSC_VDEV: declare support for a virtio device, and serve as its - * virtio header. - * @RSC_LAST: just keep this one at the end - * - * Please note that these values are used as indices to the rproc_handle_rsc - * lookup table, so please keep them sane. Moreover, @RSC_LAST is used to - * check the validity of an index before the lookup table is accessed, so - * please update it as needed. - */ -enum fw_resource_type { +Here are the various resource types that are currently supported:: + + /** + * enum fw_resource_type - types of resource entries + * + * @RSC_CARVEOUT: request for allocation of a physically contiguous + * memory region. + * @RSC_DEVMEM: request to iommu_map a memory-based peripheral. + * @RSC_TRACE: announces the availability of a trace buffer into which + * the remote processor will be writing logs. + * @RSC_VDEV: declare support for a virtio device, and serve as its + * virtio header. + * @RSC_LAST: just keep this one at the end + * + * Please note that these values are used as indices to the rproc_handle_rsc + * lookup table, so please keep them sane. Moreover, @RSC_LAST is used to + * check the validity of an index before the lookup table is accessed, so + * please update it as needed. + */ + enum fw_resource_type { RSC_CARVEOUT = 0, RSC_DEVMEM = 1, RSC_TRACE = 2, RSC_VDEV = 3, RSC_LAST = 4, -}; + }; For more details regarding a specific resource type, please see its dedicated structure in include/linux/remoteproc.h. @@ -286,7 +335,8 @@ We also expect that platform-specific resource entries will show up at some point. When that happens, we could easily add a new RSC_PLATFORM type, and hand those resources to the platform-specific rproc driver to handle. -7. Virtio and remoteproc +Virtio and remoteproc +===================== The firmware should provide remoteproc information about virtio devices that it supports, and their configurations: a RSC_VDEV resource entry diff --git a/Documentation/rfkill.txt b/Documentation/rfkill.txt index 8c174063b3f0..a289285d2412 100644 --- a/Documentation/rfkill.txt +++ b/Documentation/rfkill.txt @@ -1,13 +1,13 @@ +=============================== rfkill - RF kill switch support =============================== -1. Introduction -2. Implementation details -3. Kernel API -4. Userspace support +.. contents:: + :depth: 2 -1. Introduction +Introduction +============ The rfkill subsystem provides a generic interface to disabling any radio transmitter in the system. When a transmitter is blocked, it shall not @@ -21,17 +21,24 @@ aircraft. The rfkill subsystem has a concept of "hard" and "soft" block, which differ little in their meaning (block == transmitters off) but rather in whether they can be changed or not: - - hard block: read-only radio block that cannot be overridden by software - - soft block: writable radio block (need not be readable) that is set by - the system software. + + - hard block + read-only radio block that cannot be overridden by software + + - soft block + writable radio block (need not be readable) that is set by + the system software. The rfkill subsystem has two parameters, rfkill.default_state and -rfkill.master_switch_mode, which are documented in admin-guide/kernel-parameters.rst. +rfkill.master_switch_mode, which are documented in +admin-guide/kernel-parameters.rst. -2. Implementation details +Implementation details +====================== The rfkill subsystem is composed of three main components: + * the rfkill core, * the deprecated rfkill-input module (an input layer handler, being replaced by userspace policy code) and @@ -55,7 +62,8 @@ use the return value of rfkill_set_hw_state() unless the hardware actually keeps track of soft and hard block separately. -3. Kernel API +Kernel API +========== Drivers for radio transmitters normally implement an rfkill driver. @@ -69,7 +77,7 @@ For some platforms, it is possible that the hardware state changes during suspend/hibernation, in which case it will be necessary to update the rfkill core with the current state is at resume time. -To create an rfkill driver, driver's Kconfig needs to have +To create an rfkill driver, driver's Kconfig needs to have:: depends on RFKILL || !RFKILL @@ -87,7 +95,8 @@ RFKill provides per-switch LED triggers, which can be used to drive LEDs according to the switch state (LED_FULL when blocked, LED_OFF otherwise). -5. Userspace support +Userspace support +================= The recommended userspace interface to use is /dev/rfkill, which is a misc character device that allows userspace to obtain and set the state of rfkill @@ -112,11 +121,11 @@ rfkill core framework. Additionally, each rfkill device is registered in sysfs and emits uevents. rfkill devices issue uevents (with an action of "change"), with the following -environment variables set: +environment variables set:: -RFKILL_NAME -RFKILL_STATE -RFKILL_TYPE + RFKILL_NAME + RFKILL_STATE + RFKILL_TYPE The contents of these variables corresponds to the "name", "state" and "type" sysfs files explained above. diff --git a/Documentation/robust-futex-ABI.txt b/Documentation/robust-futex-ABI.txt index 16eb314f56cc..8a5d34abf726 100644 --- a/Documentation/robust-futex-ABI.txt +++ b/Documentation/robust-futex-ABI.txt @@ -1,7 +1,9 @@ -Started by Paul Jackson <pj@sgi.com> - +==================== The robust futex ABI --------------------- +==================== + +:Author: Started by Paul Jackson <pj@sgi.com> + Robust_futexes provide a mechanism that is used in addition to normal futexes, for kernel assist of cleanup of held locks on task exit. @@ -32,7 +34,7 @@ probably causing deadlock or other such failure of the other threads waiting on the same locks. A thread that anticipates possibly using robust_futexes should first -issue the system call: +issue the system call:: asmlinkage long sys_set_robust_list(struct robust_list_head __user *head, size_t len); @@ -91,7 +93,7 @@ that lock using the futex mechanism. When a thread has invoked the above system call to indicate it anticipates using robust_futexes, the kernel stores the passed in 'head' pointer for that task. The task may retrieve that value later on by -using the system call: +using the system call:: asmlinkage long sys_get_robust_list(int pid, struct robust_list_head __user **head_ptr, @@ -135,6 +137,7 @@ manipulating this list), the user code must observe the following protocol on 'lock entry' insertion and removal: On insertion: + 1) set the 'list_op_pending' word to the address of the 'lock entry' to be inserted, 2) acquire the futex lock, @@ -143,6 +146,7 @@ On insertion: 4) clear the 'list_op_pending' word. On removal: + 1) set the 'list_op_pending' word to the address of the 'lock entry' to be removed, 2) remove the lock entry for this lock from the 'head' list, diff --git a/Documentation/robust-futexes.txt b/Documentation/robust-futexes.txt index 61c22d608759..6c42c75103eb 100644 --- a/Documentation/robust-futexes.txt +++ b/Documentation/robust-futexes.txt @@ -1,4 +1,8 @@ -Started by: Ingo Molnar <mingo@redhat.com> +======================================== +A description of what robust futexes are +======================================== + +:Started by: Ingo Molnar <mingo@redhat.com> Background ---------- @@ -163,7 +167,7 @@ Implementation details ---------------------- The patch adds two new syscalls: one to register the userspace list, and -one to query the registered list pointer: +one to query the registered list pointer:: asmlinkage long sys_set_robust_list(struct robust_list_head __user *head, @@ -185,7 +189,7 @@ straightforward. The kernel doesn't have any internal distinction between robust and normal futexes. If a futex is found to be held at exit time, the kernel sets the -following bit of the futex word: +following bit of the futex word:: #define FUTEX_OWNER_DIED 0x40000000 @@ -193,7 +197,7 @@ and wakes up the next futex waiter (if any). User-space does the rest of the cleanup. Otherwise, robust futexes are acquired by glibc by putting the TID into -the futex field atomically. Waiters set the FUTEX_WAITERS bit: +the futex field atomically. Waiters set the FUTEX_WAITERS bit:: #define FUTEX_WAITERS 0x80000000 diff --git a/Documentation/rpmsg.txt b/Documentation/rpmsg.txt index a95e36a43288..24b7a9e1a5f9 100644 --- a/Documentation/rpmsg.txt +++ b/Documentation/rpmsg.txt @@ -1,10 +1,15 @@ +============================================ Remote Processor Messaging (rpmsg) Framework +============================================ -Note: this document describes the rpmsg bus and how to write rpmsg drivers. -To learn how to add rpmsg support for new platforms, check out remoteproc.txt -(also a resident of Documentation/). +.. note:: -1. Introduction + This document describes the rpmsg bus and how to write rpmsg drivers. + To learn how to add rpmsg support for new platforms, check out remoteproc.txt + (also a resident of Documentation/). + +Introduction +============ Modern SoCs typically employ heterogeneous remote processor devices in asymmetric multiprocessing (AMP) configurations, which may be running @@ -58,170 +63,222 @@ to their destination address (this is done by invoking the driver's rx handler with the payload of the inbound message). -2. User API +User API +======== + +:: int rpmsg_send(struct rpmsg_channel *rpdev, void *data, int len); - - sends a message across to the remote processor on a given channel. - The caller should specify the channel, the data it wants to send, - and its length (in bytes). The message will be sent on the specified - channel, i.e. its source and destination address fields will be - set to the channel's src and dst addresses. - - In case there are no TX buffers available, the function will block until - one becomes available (i.e. until the remote processor consumes - a tx buffer and puts it back on virtio's used descriptor ring), - or a timeout of 15 seconds elapses. When the latter happens, - -ERESTARTSYS is returned. - The function can only be called from a process context (for now). - Returns 0 on success and an appropriate error value on failure. + +sends a message across to the remote processor on a given channel. +The caller should specify the channel, the data it wants to send, +and its length (in bytes). The message will be sent on the specified +channel, i.e. its source and destination address fields will be +set to the channel's src and dst addresses. + +In case there are no TX buffers available, the function will block until +one becomes available (i.e. until the remote processor consumes +a tx buffer and puts it back on virtio's used descriptor ring), +or a timeout of 15 seconds elapses. When the latter happens, +-ERESTARTSYS is returned. + +The function can only be called from a process context (for now). +Returns 0 on success and an appropriate error value on failure. + +:: int rpmsg_sendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst); - - sends a message across to the remote processor on a given channel, - to a destination address provided by the caller. - The caller should specify the channel, the data it wants to send, - its length (in bytes), and an explicit destination address. - The message will then be sent to the remote processor to which the - channel belongs, using the channel's src address, and the user-provided - dst address (thus the channel's dst address will be ignored). - - In case there are no TX buffers available, the function will block until - one becomes available (i.e. until the remote processor consumes - a tx buffer and puts it back on virtio's used descriptor ring), - or a timeout of 15 seconds elapses. When the latter happens, - -ERESTARTSYS is returned. - The function can only be called from a process context (for now). - Returns 0 on success and an appropriate error value on failure. + +sends a message across to the remote processor on a given channel, +to a destination address provided by the caller. + +The caller should specify the channel, the data it wants to send, +its length (in bytes), and an explicit destination address. + +The message will then be sent to the remote processor to which the +channel belongs, using the channel's src address, and the user-provided +dst address (thus the channel's dst address will be ignored). + +In case there are no TX buffers available, the function will block until +one becomes available (i.e. until the remote processor consumes +a tx buffer and puts it back on virtio's used descriptor ring), +or a timeout of 15 seconds elapses. When the latter happens, +-ERESTARTSYS is returned. + +The function can only be called from a process context (for now). +Returns 0 on success and an appropriate error value on failure. + +:: int rpmsg_send_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst, void *data, int len); - - sends a message across to the remote processor, using the src and dst - addresses provided by the user. - The caller should specify the channel, the data it wants to send, - its length (in bytes), and explicit source and destination addresses. - The message will then be sent to the remote processor to which the - channel belongs, but the channel's src and dst addresses will be - ignored (and the user-provided addresses will be used instead). - - In case there are no TX buffers available, the function will block until - one becomes available (i.e. until the remote processor consumes - a tx buffer and puts it back on virtio's used descriptor ring), - or a timeout of 15 seconds elapses. When the latter happens, - -ERESTARTSYS is returned. - The function can only be called from a process context (for now). - Returns 0 on success and an appropriate error value on failure. + + +sends a message across to the remote processor, using the src and dst +addresses provided by the user. + +The caller should specify the channel, the data it wants to send, +its length (in bytes), and explicit source and destination addresses. +The message will then be sent to the remote processor to which the +channel belongs, but the channel's src and dst addresses will be +ignored (and the user-provided addresses will be used instead). + +In case there are no TX buffers available, the function will block until +one becomes available (i.e. until the remote processor consumes +a tx buffer and puts it back on virtio's used descriptor ring), +or a timeout of 15 seconds elapses. When the latter happens, +-ERESTARTSYS is returned. + +The function can only be called from a process context (for now). +Returns 0 on success and an appropriate error value on failure. + +:: int rpmsg_trysend(struct rpmsg_channel *rpdev, void *data, int len); - - sends a message across to the remote processor on a given channel. - The caller should specify the channel, the data it wants to send, - and its length (in bytes). The message will be sent on the specified - channel, i.e. its source and destination address fields will be - set to the channel's src and dst addresses. - In case there are no TX buffers available, the function will immediately - return -ENOMEM without waiting until one becomes available. - The function can only be called from a process context (for now). - Returns 0 on success and an appropriate error value on failure. +sends a message across to the remote processor on a given channel. +The caller should specify the channel, the data it wants to send, +and its length (in bytes). The message will be sent on the specified +channel, i.e. its source and destination address fields will be +set to the channel's src and dst addresses. + +In case there are no TX buffers available, the function will immediately +return -ENOMEM without waiting until one becomes available. + +The function can only be called from a process context (for now). +Returns 0 on success and an appropriate error value on failure. + +:: int rpmsg_trysendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst) - - sends a message across to the remote processor on a given channel, - to a destination address provided by the user. - The user should specify the channel, the data it wants to send, - its length (in bytes), and an explicit destination address. - The message will then be sent to the remote processor to which the - channel belongs, using the channel's src address, and the user-provided - dst address (thus the channel's dst address will be ignored). - - In case there are no TX buffers available, the function will immediately - return -ENOMEM without waiting until one becomes available. - The function can only be called from a process context (for now). - Returns 0 on success and an appropriate error value on failure. + + +sends a message across to the remote processor on a given channel, +to a destination address provided by the user. + +The user should specify the channel, the data it wants to send, +its length (in bytes), and an explicit destination address. + +The message will then be sent to the remote processor to which the +channel belongs, using the channel's src address, and the user-provided +dst address (thus the channel's dst address will be ignored). + +In case there are no TX buffers available, the function will immediately +return -ENOMEM without waiting until one becomes available. + +The function can only be called from a process context (for now). +Returns 0 on success and an appropriate error value on failure. + +:: int rpmsg_trysend_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst, void *data, int len); - - sends a message across to the remote processor, using source and - destination addresses provided by the user. - The user should specify the channel, the data it wants to send, - its length (in bytes), and explicit source and destination addresses. - The message will then be sent to the remote processor to which the - channel belongs, but the channel's src and dst addresses will be - ignored (and the user-provided addresses will be used instead). - - In case there are no TX buffers available, the function will immediately - return -ENOMEM without waiting until one becomes available. - The function can only be called from a process context (for now). - Returns 0 on success and an appropriate error value on failure. + + +sends a message across to the remote processor, using source and +destination addresses provided by the user. + +The user should specify the channel, the data it wants to send, +its length (in bytes), and explicit source and destination addresses. +The message will then be sent to the remote processor to which the +channel belongs, but the channel's src and dst addresses will be +ignored (and the user-provided addresses will be used instead). + +In case there are no TX buffers available, the function will immediately +return -ENOMEM without waiting until one becomes available. + +The function can only be called from a process context (for now). +Returns 0 on success and an appropriate error value on failure. + +:: struct rpmsg_endpoint *rpmsg_create_ept(struct rpmsg_channel *rpdev, void (*cb)(struct rpmsg_channel *, void *, int, void *, u32), void *priv, u32 addr); - - every rpmsg address in the system is bound to an rx callback (so when - inbound messages arrive, they are dispatched by the rpmsg bus using the - appropriate callback handler) by means of an rpmsg_endpoint struct. - - This function allows drivers to create such an endpoint, and by that, - bind a callback, and possibly some private data too, to an rpmsg address - (either one that is known in advance, or one that will be dynamically - assigned for them). - - Simple rpmsg drivers need not call rpmsg_create_ept, because an endpoint - is already created for them when they are probed by the rpmsg bus - (using the rx callback they provide when they registered to the rpmsg bus). - - So things should just work for simple drivers: they already have an - endpoint, their rx callback is bound to their rpmsg address, and when - relevant inbound messages arrive (i.e. messages which their dst address - equals to the src address of their rpmsg channel), the driver's handler - is invoked to process it. - - That said, more complicated drivers might do need to allocate - additional rpmsg addresses, and bind them to different rx callbacks. - To accomplish that, those drivers need to call this function. - Drivers should provide their channel (so the new endpoint would bind - to the same remote processor their channel belongs to), an rx callback - function, an optional private data (which is provided back when the - rx callback is invoked), and an address they want to bind with the - callback. If addr is RPMSG_ADDR_ANY, then rpmsg_create_ept will - dynamically assign them an available rpmsg address (drivers should have - a very good reason why not to always use RPMSG_ADDR_ANY here). - - Returns a pointer to the endpoint on success, or NULL on error. + +every rpmsg address in the system is bound to an rx callback (so when +inbound messages arrive, they are dispatched by the rpmsg bus using the +appropriate callback handler) by means of an rpmsg_endpoint struct. + +This function allows drivers to create such an endpoint, and by that, +bind a callback, and possibly some private data too, to an rpmsg address +(either one that is known in advance, or one that will be dynamically +assigned for them). + +Simple rpmsg drivers need not call rpmsg_create_ept, because an endpoint +is already created for them when they are probed by the rpmsg bus +(using the rx callback they provide when they registered to the rpmsg bus). + +So things should just work for simple drivers: they already have an +endpoint, their rx callback is bound to their rpmsg address, and when +relevant inbound messages arrive (i.e. messages which their dst address +equals to the src address of their rpmsg channel), the driver's handler +is invoked to process it. + +That said, more complicated drivers might do need to allocate +additional rpmsg addresses, and bind them to different rx callbacks. +To accomplish that, those drivers need to call this function. +Drivers should provide their channel (so the new endpoint would bind +to the same remote processor their channel belongs to), an rx callback +function, an optional private data (which is provided back when the +rx callback is invoked), and an address they want to bind with the +callback. If addr is RPMSG_ADDR_ANY, then rpmsg_create_ept will +dynamically assign them an available rpmsg address (drivers should have +a very good reason why not to always use RPMSG_ADDR_ANY here). + +Returns a pointer to the endpoint on success, or NULL on error. + +:: void rpmsg_destroy_ept(struct rpmsg_endpoint *ept); - - destroys an existing rpmsg endpoint. user should provide a pointer - to an rpmsg endpoint that was previously created with rpmsg_create_ept(). + + +destroys an existing rpmsg endpoint. user should provide a pointer +to an rpmsg endpoint that was previously created with rpmsg_create_ept(). + +:: int register_rpmsg_driver(struct rpmsg_driver *rpdrv); - - registers an rpmsg driver with the rpmsg bus. user should provide - a pointer to an rpmsg_driver struct, which contains the driver's - ->probe() and ->remove() functions, an rx callback, and an id_table - specifying the names of the channels this driver is interested to - be probed with. + + +registers an rpmsg driver with the rpmsg bus. user should provide +a pointer to an rpmsg_driver struct, which contains the driver's +->probe() and ->remove() functions, an rx callback, and an id_table +specifying the names of the channels this driver is interested to +be probed with. + +:: void unregister_rpmsg_driver(struct rpmsg_driver *rpdrv); - - unregisters an rpmsg driver from the rpmsg bus. user should provide - a pointer to a previously-registered rpmsg_driver struct. - Returns 0 on success, and an appropriate error value on failure. -3. Typical usage +unregisters an rpmsg driver from the rpmsg bus. user should provide +a pointer to a previously-registered rpmsg_driver struct. +Returns 0 on success, and an appropriate error value on failure. + + +Typical usage +============= The following is a simple rpmsg driver, that sends an "hello!" message on probe(), and whenever it receives an incoming message, it dumps its content to the console. -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/rpmsg.h> +:: + + #include <linux/kernel.h> + #include <linux/module.h> + #include <linux/rpmsg.h> -static void rpmsg_sample_cb(struct rpmsg_channel *rpdev, void *data, int len, + static void rpmsg_sample_cb(struct rpmsg_channel *rpdev, void *data, int len, void *priv, u32 src) -{ + { print_hex_dump(KERN_INFO, "incoming message:", DUMP_PREFIX_NONE, 16, 1, data, len, true); -} + } -static int rpmsg_sample_probe(struct rpmsg_channel *rpdev) -{ + static int rpmsg_sample_probe(struct rpmsg_channel *rpdev) + { int err; dev_info(&rpdev->dev, "chnl: 0x%x -> 0x%x\n", rpdev->src, rpdev->dst); @@ -234,32 +291,35 @@ static int rpmsg_sample_probe(struct rpmsg_channel *rpdev) } return 0; -} + } -static void rpmsg_sample_remove(struct rpmsg_channel *rpdev) -{ + static void rpmsg_sample_remove(struct rpmsg_channel *rpdev) + { dev_info(&rpdev->dev, "rpmsg sample client driver is removed\n"); -} + } -static struct rpmsg_device_id rpmsg_driver_sample_id_table[] = { + static struct rpmsg_device_id rpmsg_driver_sample_id_table[] = { { .name = "rpmsg-client-sample" }, { }, -}; -MODULE_DEVICE_TABLE(rpmsg, rpmsg_driver_sample_id_table); + }; + MODULE_DEVICE_TABLE(rpmsg, rpmsg_driver_sample_id_table); -static struct rpmsg_driver rpmsg_sample_client = { + static struct rpmsg_driver rpmsg_sample_client = { .drv.name = KBUILD_MODNAME, .id_table = rpmsg_driver_sample_id_table, .probe = rpmsg_sample_probe, .callback = rpmsg_sample_cb, .remove = rpmsg_sample_remove, -}; -module_rpmsg_driver(rpmsg_sample_client); + }; + module_rpmsg_driver(rpmsg_sample_client); + +.. note:: -Note: a similar sample which can be built and loaded can be found -in samples/rpmsg/. + a similar sample which can be built and loaded can be found + in samples/rpmsg/. -4. Allocations of rpmsg channels: +Allocations of rpmsg channels +============================= At this point we only support dynamic allocations of rpmsg channels. diff --git a/Documentation/rtc.txt b/Documentation/rtc.txt index ddc366026e00..c0c977445fb9 100644 --- a/Documentation/rtc.txt +++ b/Documentation/rtc.txt @@ -1,6 +1,6 @@ - - Real Time Clock (RTC) Drivers for Linux - ======================================= +======================================= +Real Time Clock (RTC) Drivers for Linux +======================================= When Linux developers talk about a "Real Time Clock", they usually mean something that tracks wall clock time and is battery backed so that it @@ -32,8 +32,8 @@ only issue an alarm up to 24 hours in the future, other hardware may be able to schedule one any time in the upcoming century. - Old PC/AT-Compatible driver: /dev/rtc - -------------------------------------- +Old PC/AT-Compatible driver: /dev/rtc +-------------------------------------- All PCs (even Alpha machines) have a Real Time Clock built into them. Usually they are built into the chipset of the computer, but some may @@ -105,8 +105,8 @@ that will be using this driver. See the code at the end of this document. (The original /dev/rtc driver was written by Paul Gortmaker.) - New portable "RTC Class" drivers: /dev/rtcN - -------------------------------------------- +New portable "RTC Class" drivers: /dev/rtcN +-------------------------------------------- Because Linux supports many non-ACPI and non-PC platforms, some of which have more than one RTC style clock, it needed a more portable solution @@ -136,35 +136,39 @@ a high functionality RTC is integrated into the SOC. That system might read the system clock from the discrete RTC, but use the integrated one for all other tasks, because of its greater functionality. -SYSFS INTERFACE +SYSFS interface --------------- The sysfs interface under /sys/class/rtc/rtcN provides access to various rtc attributes without requiring the use of ioctls. All dates and times are in the RTC's timezone, rather than in system time. -date: RTC-provided date -hctosys: 1 if the RTC provided the system time at boot via the +================ ============================================================== +date RTC-provided date +hctosys 1 if the RTC provided the system time at boot via the CONFIG_RTC_HCTOSYS kernel option, 0 otherwise -max_user_freq: The maximum interrupt rate an unprivileged user may request +max_user_freq The maximum interrupt rate an unprivileged user may request from this RTC. -name: The name of the RTC corresponding to this sysfs directory -since_epoch: The number of seconds since the epoch according to the RTC -time: RTC-provided time -wakealarm: The time at which the clock will generate a system wakeup +name The name of the RTC corresponding to this sysfs directory +since_epoch The number of seconds since the epoch according to the RTC +time RTC-provided time +wakealarm The time at which the clock will generate a system wakeup event. This is a one shot wakeup event, so must be reset - after wake if a daily wakeup is required. Format is seconds since - the epoch by default, or if there's a leading +, seconds in the - future, or if there is a leading +=, seconds ahead of the current - alarm. -offset: The amount which the rtc clock has been adjusted in firmware. + after wake if a daily wakeup is required. Format is seconds + since the epoch by default, or if there's a leading +, seconds + in the future, or if there is a leading +=, seconds ahead of + the current alarm. +offset The amount which the rtc clock has been adjusted in firmware. Visible only if the driver supports clock offset adjustment. The unit is parts per billion, i.e. The number of clock ticks which are added to or removed from the rtc's base clock per billion ticks. A positive value makes a day pass more slowly, longer, and a negative value makes a day pass more quickly. +*/nvmem The non volatile storage exported as a raw file, as described + in Documentation/nvmem/nvmem.txt +================ ============================================================== -IOCTL INTERFACE +IOCTL interface --------------- The ioctl() calls supported by /dev/rtc are also supported by the RTC class diff --git a/Documentation/security/keys/core.rst b/Documentation/security/keys/core.rst index 0d831a7afe4f..1648fa80b3bf 100644 --- a/Documentation/security/keys/core.rst +++ b/Documentation/security/keys/core.rst @@ -894,6 +894,12 @@ The keyctl syscall functions are: To apply a keyring restriction the process must have Set Attribute permission and the keyring must not be previously restricted. + One application of restricted keyrings is to verify X.509 certificate + chains or individual certificate signatures using the asymmetric key type. + See Documentation/crypto/asymmetric-keys.txt for specific restrictions + applicable to the asymmetric key type. + + Kernel Services =============== diff --git a/Documentation/sgi-ioc4.txt b/Documentation/sgi-ioc4.txt index 876c96ae38db..72709222d3c0 100644 --- a/Documentation/sgi-ioc4.txt +++ b/Documentation/sgi-ioc4.txt @@ -1,3 +1,7 @@ +==================================== +SGI IOC4 PCI (multi function) device +==================================== + The SGI IOC4 PCI device is a bit of a strange beast, so some notes on it are in order. diff --git a/Documentation/siphash.txt b/Documentation/siphash.txt index 908d348ff777..9965821ab333 100644 --- a/Documentation/siphash.txt +++ b/Documentation/siphash.txt @@ -1,6 +1,8 @@ - SipHash - a short input PRF ------------------------------------------------ -Written by Jason A. Donenfeld <jason@zx2c4.com> +=========================== +SipHash - a short input PRF +=========================== + +:Author: Written by Jason A. Donenfeld <jason@zx2c4.com> SipHash is a cryptographically secure PRF -- a keyed hash function -- that performs very well for short inputs, hence the name. It was designed by @@ -13,58 +15,61 @@ an input buffer or several input integers. It spits out an integer that is indistinguishable from random. You may then use that integer as part of secure sequence numbers, secure cookies, or mask it off for use in a hash table. -1. Generating a key +Generating a key +================ Keys should always be generated from a cryptographically secure source of -random numbers, either using get_random_bytes or get_random_once: +random numbers, either using get_random_bytes or get_random_once:: -siphash_key_t key; -get_random_bytes(&key, sizeof(key)); + siphash_key_t key; + get_random_bytes(&key, sizeof(key)); If you're not deriving your key from here, you're doing it wrong. -2. Using the functions +Using the functions +=================== There are two variants of the function, one that takes a list of integers, and -one that takes a buffer: +one that takes a buffer:: -u64 siphash(const void *data, size_t len, const siphash_key_t *key); + u64 siphash(const void *data, size_t len, const siphash_key_t *key); -And: +And:: -u64 siphash_1u64(u64, const siphash_key_t *key); -u64 siphash_2u64(u64, u64, const siphash_key_t *key); -u64 siphash_3u64(u64, u64, u64, const siphash_key_t *key); -u64 siphash_4u64(u64, u64, u64, u64, const siphash_key_t *key); -u64 siphash_1u32(u32, const siphash_key_t *key); -u64 siphash_2u32(u32, u32, const siphash_key_t *key); -u64 siphash_3u32(u32, u32, u32, const siphash_key_t *key); -u64 siphash_4u32(u32, u32, u32, u32, const siphash_key_t *key); + u64 siphash_1u64(u64, const siphash_key_t *key); + u64 siphash_2u64(u64, u64, const siphash_key_t *key); + u64 siphash_3u64(u64, u64, u64, const siphash_key_t *key); + u64 siphash_4u64(u64, u64, u64, u64, const siphash_key_t *key); + u64 siphash_1u32(u32, const siphash_key_t *key); + u64 siphash_2u32(u32, u32, const siphash_key_t *key); + u64 siphash_3u32(u32, u32, u32, const siphash_key_t *key); + u64 siphash_4u32(u32, u32, u32, u32, const siphash_key_t *key); If you pass the generic siphash function something of a constant length, it will constant fold at compile-time and automatically choose one of the optimized functions. -3. Hashtable key function usage: +Hashtable key function usage:: -struct some_hashtable { - DECLARE_HASHTABLE(hashtable, 8); - siphash_key_t key; -}; + struct some_hashtable { + DECLARE_HASHTABLE(hashtable, 8); + siphash_key_t key; + }; -void init_hashtable(struct some_hashtable *table) -{ - get_random_bytes(&table->key, sizeof(table->key)); -} + void init_hashtable(struct some_hashtable *table) + { + get_random_bytes(&table->key, sizeof(table->key)); + } -static inline hlist_head *some_hashtable_bucket(struct some_hashtable *table, struct interesting_input *input) -{ - return &table->hashtable[siphash(input, sizeof(*input), &table->key) & (HASH_SIZE(table->hashtable) - 1)]; -} + static inline hlist_head *some_hashtable_bucket(struct some_hashtable *table, struct interesting_input *input) + { + return &table->hashtable[siphash(input, sizeof(*input), &table->key) & (HASH_SIZE(table->hashtable) - 1)]; + } You may then iterate like usual over the returned hash bucket. -4. Security +Security +======== SipHash has a very high security margin, with its 128-bit key. So long as the key is kept secret, it is impossible for an attacker to guess the outputs of @@ -73,7 +78,8 @@ is significant. Linux implements the "2-4" variant of SipHash. -5. Struct-passing Pitfalls +Struct-passing Pitfalls +======================= Often times the XuY functions will not be large enough, and instead you'll want to pass a pre-filled struct to siphash. When doing this, it's important @@ -81,30 +87,32 @@ to always ensure the struct has no padding holes. The easiest way to do this is to simply arrange the members of the struct in descending order of size, and to use offsetendof() instead of sizeof() for getting the size. For performance reasons, if possible, it's probably a good thing to align the -struct to the right boundary. Here's an example: - -const struct { - struct in6_addr saddr; - u32 counter; - u16 dport; -} __aligned(SIPHASH_ALIGNMENT) combined = { - .saddr = *(struct in6_addr *)saddr, - .counter = counter, - .dport = dport -}; -u64 h = siphash(&combined, offsetofend(typeof(combined), dport), &secret); - -6. Resources +struct to the right boundary. Here's an example:: + + const struct { + struct in6_addr saddr; + u32 counter; + u16 dport; + } __aligned(SIPHASH_ALIGNMENT) combined = { + .saddr = *(struct in6_addr *)saddr, + .counter = counter, + .dport = dport + }; + u64 h = siphash(&combined, offsetofend(typeof(combined), dport), &secret); + +Resources +========= Read the SipHash paper if you're interested in learning more: https://131002.net/siphash/siphash.pdf +------------------------------------------------------------------------------- -~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~=~ - +=============================================== HalfSipHash - SipHash's insecure younger cousin ------------------------------------------------ -Written by Jason A. Donenfeld <jason@zx2c4.com> +=============================================== + +:Author: Written by Jason A. Donenfeld <jason@zx2c4.com> On the off-chance that SipHash is not fast enough for your needs, you might be able to justify using HalfSipHash, a terrifying but potentially useful @@ -120,7 +128,8 @@ then when you can be absolutely certain that the outputs will never be transmitted out of the kernel. This is only remotely useful over `jhash` as a means of mitigating hashtable flooding denial of service attacks. -1. Generating a key +Generating a key +================ Keys should always be generated from a cryptographically secure source of random numbers, either using get_random_bytes or get_random_once: @@ -130,44 +139,49 @@ get_random_bytes(&key, sizeof(key)); If you're not deriving your key from here, you're doing it wrong. -2. Using the functions +Using the functions +=================== There are two variants of the function, one that takes a list of integers, and -one that takes a buffer: +one that takes a buffer:: -u32 hsiphash(const void *data, size_t len, const hsiphash_key_t *key); + u32 hsiphash(const void *data, size_t len, const hsiphash_key_t *key); -And: +And:: -u32 hsiphash_1u32(u32, const hsiphash_key_t *key); -u32 hsiphash_2u32(u32, u32, const hsiphash_key_t *key); -u32 hsiphash_3u32(u32, u32, u32, const hsiphash_key_t *key); -u32 hsiphash_4u32(u32, u32, u32, u32, const hsiphash_key_t *key); + u32 hsiphash_1u32(u32, const hsiphash_key_t *key); + u32 hsiphash_2u32(u32, u32, const hsiphash_key_t *key); + u32 hsiphash_3u32(u32, u32, u32, const hsiphash_key_t *key); + u32 hsiphash_4u32(u32, u32, u32, u32, const hsiphash_key_t *key); If you pass the generic hsiphash function something of a constant length, it will constant fold at compile-time and automatically choose one of the optimized functions. -3. Hashtable key function usage: +Hashtable key function usage +============================ + +:: -struct some_hashtable { - DECLARE_HASHTABLE(hashtable, 8); - hsiphash_key_t key; -}; + struct some_hashtable { + DECLARE_HASHTABLE(hashtable, 8); + hsiphash_key_t key; + }; -void init_hashtable(struct some_hashtable *table) -{ - get_random_bytes(&table->key, sizeof(table->key)); -} + void init_hashtable(struct some_hashtable *table) + { + get_random_bytes(&table->key, sizeof(table->key)); + } -static inline hlist_head *some_hashtable_bucket(struct some_hashtable *table, struct interesting_input *input) -{ - return &table->hashtable[hsiphash(input, sizeof(*input), &table->key) & (HASH_SIZE(table->hashtable) - 1)]; -} + static inline hlist_head *some_hashtable_bucket(struct some_hashtable *table, struct interesting_input *input) + { + return &table->hashtable[hsiphash(input, sizeof(*input), &table->key) & (HASH_SIZE(table->hashtable) - 1)]; + } You may then iterate like usual over the returned hash bucket. -4. Performance +Performance +=========== HalfSipHash is roughly 3 times slower than JenkinsHash. For many replacements, this will not be a problem, as the hashtable lookup isn't the bottleneck. And diff --git a/Documentation/smsc_ece1099.txt b/Documentation/smsc_ece1099.txt index 6b492e82b43d..079277421eaf 100644 --- a/Documentation/smsc_ece1099.txt +++ b/Documentation/smsc_ece1099.txt @@ -1,3 +1,7 @@ +================================================= +Msc Keyboard Scan Expansion/GPIO Expansion device +================================================= + What is smsc-ece1099? ---------------------- diff --git a/Documentation/static-keys.txt b/Documentation/static-keys.txt index ef419fd0897f..b83dfa1c0602 100644 --- a/Documentation/static-keys.txt +++ b/Documentation/static-keys.txt @@ -1,30 +1,34 @@ - Static Keys - ----------- +=========== +Static Keys +=========== -DEPRECATED API: +.. warning:: -The use of 'struct static_key' directly, is now DEPRECATED. In addition -static_key_{true,false}() is also DEPRECATED. IE DO NOT use the following: + DEPRECATED API: -struct static_key false = STATIC_KEY_INIT_FALSE; -struct static_key true = STATIC_KEY_INIT_TRUE; -static_key_true() -static_key_false() + The use of 'struct static_key' directly, is now DEPRECATED. In addition + static_key_{true,false}() is also DEPRECATED. IE DO NOT use the following:: -The updated API replacements are: + struct static_key false = STATIC_KEY_INIT_FALSE; + struct static_key true = STATIC_KEY_INIT_TRUE; + static_key_true() + static_key_false() -DEFINE_STATIC_KEY_TRUE(key); -DEFINE_STATIC_KEY_FALSE(key); -DEFINE_STATIC_KEY_ARRAY_TRUE(keys, count); -DEFINE_STATIC_KEY_ARRAY_FALSE(keys, count); -static_branch_likely() -static_branch_unlikely() + The updated API replacements are:: -0) Abstract + DEFINE_STATIC_KEY_TRUE(key); + DEFINE_STATIC_KEY_FALSE(key); + DEFINE_STATIC_KEY_ARRAY_TRUE(keys, count); + DEFINE_STATIC_KEY_ARRAY_FALSE(keys, count); + static_branch_likely() + static_branch_unlikely() + +Abstract +======== Static keys allows the inclusion of seldom used features in performance-sensitive fast-path kernel code, via a GCC feature and a code -patching technique. A quick example: +patching technique. A quick example:: DEFINE_STATIC_KEY_FALSE(key); @@ -45,7 +49,8 @@ The static_branch_unlikely() branch will be generated into the code with as litt impact to the likely code path as possible. -1) Motivation +Motivation +========== Currently, tracepoints are implemented using a conditional branch. The @@ -60,7 +65,8 @@ possible. Although tracepoints are the original motivation for this work, other kernel code paths should be able to make use of the static keys facility. -2) Solution +Solution +======== gcc (v4.5) adds a new 'asm goto' statement that allows branching to a label: @@ -71,7 +77,7 @@ Using the 'asm goto', we can create branches that are either taken or not taken by default, without the need to check memory. Then, at run-time, we can patch the branch site to change the branch direction. -For example, if we have a simple branch that is disabled by default: +For example, if we have a simple branch that is disabled by default:: if (static_branch_unlikely(&key)) printk("I am the true branch\n"); @@ -87,14 +93,15 @@ optimization. This lowlevel patching mechanism is called 'jump label patching', and it gives the basis for the static keys facility. -3) Static key label API, usage and examples: +Static key label API, usage and examples +======================================== -In order to make use of this optimization you must first define a key: +In order to make use of this optimization you must first define a key:: DEFINE_STATIC_KEY_TRUE(key); -or: +or:: DEFINE_STATIC_KEY_FALSE(key); @@ -102,14 +109,14 @@ or: The key must be global, that is, it can't be allocated on the stack or dynamically allocated at run-time. -The key is then used in code as: +The key is then used in code as:: if (static_branch_unlikely(&key)) do unlikely code else do likely code -Or: +Or:: if (static_branch_likely(&key)) do likely code @@ -120,15 +127,15 @@ Keys defined via DEFINE_STATIC_KEY_TRUE(), or DEFINE_STATIC_KEY_FALSE, may be used in either static_branch_likely() or static_branch_unlikely() statements. -Branch(es) can be set true via: +Branch(es) can be set true via:: -static_branch_enable(&key); + static_branch_enable(&key); -or false via: +or false via:: -static_branch_disable(&key); + static_branch_disable(&key); -The branch(es) can then be switched via reference counts: +The branch(es) can then be switched via reference counts:: static_branch_inc(&key); ... @@ -142,11 +149,11 @@ static_branch_inc(), will change the branch back to true. Likewise, if the key is initialized false, a 'static_branch_inc()', will change the branch to true. And then a 'static_branch_dec()', will again make the branch false. -Where an array of keys is required, it can be defined as: +Where an array of keys is required, it can be defined as:: DEFINE_STATIC_KEY_ARRAY_TRUE(keys, count); -or: +or:: DEFINE_STATIC_KEY_ARRAY_FALSE(keys, count); @@ -159,96 +166,98 @@ simply fall back to a traditional, load, test, and jump sequence. Also, the struct jump_entry table must be at least 4-byte aligned because the static_key->entry field makes use of the two least significant bits. -* select HAVE_ARCH_JUMP_LABEL, see: arch/x86/Kconfig - -* #define JUMP_LABEL_NOP_SIZE, see: arch/x86/include/asm/jump_label.h +* ``select HAVE_ARCH_JUMP_LABEL``, + see: arch/x86/Kconfig -* __always_inline bool arch_static_branch(struct static_key *key, bool branch), see: - arch/x86/include/asm/jump_label.h +* ``#define JUMP_LABEL_NOP_SIZE``, + see: arch/x86/include/asm/jump_label.h -* __always_inline bool arch_static_branch_jump(struct static_key *key, bool branch), - see: arch/x86/include/asm/jump_label.h +* ``__always_inline bool arch_static_branch(struct static_key *key, bool branch)``, + see: arch/x86/include/asm/jump_label.h -* void arch_jump_label_transform(struct jump_entry *entry, enum jump_label_type type), - see: arch/x86/kernel/jump_label.c +* ``__always_inline bool arch_static_branch_jump(struct static_key *key, bool branch)``, + see: arch/x86/include/asm/jump_label.h -* __init_or_module void arch_jump_label_transform_static(struct jump_entry *entry, enum jump_label_type type), - see: arch/x86/kernel/jump_label.c +* ``void arch_jump_label_transform(struct jump_entry *entry, enum jump_label_type type)``, + see: arch/x86/kernel/jump_label.c +* ``__init_or_module void arch_jump_label_transform_static(struct jump_entry *entry, enum jump_label_type type)``, + see: arch/x86/kernel/jump_label.c -* struct jump_entry, see: arch/x86/include/asm/jump_label.h +* ``struct jump_entry``, + see: arch/x86/include/asm/jump_label.h 5) Static keys / jump label analysis, results (x86_64): As an example, let's add the following branch to 'getppid()', such that the -system call now looks like: +system call now looks like:: -SYSCALL_DEFINE0(getppid) -{ + SYSCALL_DEFINE0(getppid) + { int pid; -+ if (static_branch_unlikely(&key)) -+ printk("I am the true branch\n"); + + if (static_branch_unlikely(&key)) + + printk("I am the true branch\n"); rcu_read_lock(); pid = task_tgid_vnr(rcu_dereference(current->real_parent)); rcu_read_unlock(); return pid; -} - -The resulting instructions with jump labels generated by GCC is: - -ffffffff81044290 <sys_getppid>: -ffffffff81044290: 55 push %rbp -ffffffff81044291: 48 89 e5 mov %rsp,%rbp -ffffffff81044294: e9 00 00 00 00 jmpq ffffffff81044299 <sys_getppid+0x9> -ffffffff81044299: 65 48 8b 04 25 c0 b6 mov %gs:0xb6c0,%rax -ffffffff810442a0: 00 00 -ffffffff810442a2: 48 8b 80 80 02 00 00 mov 0x280(%rax),%rax -ffffffff810442a9: 48 8b 80 b0 02 00 00 mov 0x2b0(%rax),%rax -ffffffff810442b0: 48 8b b8 e8 02 00 00 mov 0x2e8(%rax),%rdi -ffffffff810442b7: e8 f4 d9 00 00 callq ffffffff81051cb0 <pid_vnr> -ffffffff810442bc: 5d pop %rbp -ffffffff810442bd: 48 98 cltq -ffffffff810442bf: c3 retq -ffffffff810442c0: 48 c7 c7 e3 54 98 81 mov $0xffffffff819854e3,%rdi -ffffffff810442c7: 31 c0 xor %eax,%eax -ffffffff810442c9: e8 71 13 6d 00 callq ffffffff8171563f <printk> -ffffffff810442ce: eb c9 jmp ffffffff81044299 <sys_getppid+0x9> - -Without the jump label optimization it looks like: - -ffffffff810441f0 <sys_getppid>: -ffffffff810441f0: 8b 05 8a 52 d8 00 mov 0xd8528a(%rip),%eax # ffffffff81dc9480 <key> -ffffffff810441f6: 55 push %rbp -ffffffff810441f7: 48 89 e5 mov %rsp,%rbp -ffffffff810441fa: 85 c0 test %eax,%eax -ffffffff810441fc: 75 27 jne ffffffff81044225 <sys_getppid+0x35> -ffffffff810441fe: 65 48 8b 04 25 c0 b6 mov %gs:0xb6c0,%rax -ffffffff81044205: 00 00 -ffffffff81044207: 48 8b 80 80 02 00 00 mov 0x280(%rax),%rax -ffffffff8104420e: 48 8b 80 b0 02 00 00 mov 0x2b0(%rax),%rax -ffffffff81044215: 48 8b b8 e8 02 00 00 mov 0x2e8(%rax),%rdi -ffffffff8104421c: e8 2f da 00 00 callq ffffffff81051c50 <pid_vnr> -ffffffff81044221: 5d pop %rbp -ffffffff81044222: 48 98 cltq -ffffffff81044224: c3 retq -ffffffff81044225: 48 c7 c7 13 53 98 81 mov $0xffffffff81985313,%rdi -ffffffff8104422c: 31 c0 xor %eax,%eax -ffffffff8104422e: e8 60 0f 6d 00 callq ffffffff81715193 <printk> -ffffffff81044233: eb c9 jmp ffffffff810441fe <sys_getppid+0xe> -ffffffff81044235: 66 66 2e 0f 1f 84 00 data32 nopw %cs:0x0(%rax,%rax,1) -ffffffff8104423c: 00 00 00 00 + } + +The resulting instructions with jump labels generated by GCC is:: + + ffffffff81044290 <sys_getppid>: + ffffffff81044290: 55 push %rbp + ffffffff81044291: 48 89 e5 mov %rsp,%rbp + ffffffff81044294: e9 00 00 00 00 jmpq ffffffff81044299 <sys_getppid+0x9> + ffffffff81044299: 65 48 8b 04 25 c0 b6 mov %gs:0xb6c0,%rax + ffffffff810442a0: 00 00 + ffffffff810442a2: 48 8b 80 80 02 00 00 mov 0x280(%rax),%rax + ffffffff810442a9: 48 8b 80 b0 02 00 00 mov 0x2b0(%rax),%rax + ffffffff810442b0: 48 8b b8 e8 02 00 00 mov 0x2e8(%rax),%rdi + ffffffff810442b7: e8 f4 d9 00 00 callq ffffffff81051cb0 <pid_vnr> + ffffffff810442bc: 5d pop %rbp + ffffffff810442bd: 48 98 cltq + ffffffff810442bf: c3 retq + ffffffff810442c0: 48 c7 c7 e3 54 98 81 mov $0xffffffff819854e3,%rdi + ffffffff810442c7: 31 c0 xor %eax,%eax + ffffffff810442c9: e8 71 13 6d 00 callq ffffffff8171563f <printk> + ffffffff810442ce: eb c9 jmp ffffffff81044299 <sys_getppid+0x9> + +Without the jump label optimization it looks like:: + + ffffffff810441f0 <sys_getppid>: + ffffffff810441f0: 8b 05 8a 52 d8 00 mov 0xd8528a(%rip),%eax # ffffffff81dc9480 <key> + ffffffff810441f6: 55 push %rbp + ffffffff810441f7: 48 89 e5 mov %rsp,%rbp + ffffffff810441fa: 85 c0 test %eax,%eax + ffffffff810441fc: 75 27 jne ffffffff81044225 <sys_getppid+0x35> + ffffffff810441fe: 65 48 8b 04 25 c0 b6 mov %gs:0xb6c0,%rax + ffffffff81044205: 00 00 + ffffffff81044207: 48 8b 80 80 02 00 00 mov 0x280(%rax),%rax + ffffffff8104420e: 48 8b 80 b0 02 00 00 mov 0x2b0(%rax),%rax + ffffffff81044215: 48 8b b8 e8 02 00 00 mov 0x2e8(%rax),%rdi + ffffffff8104421c: e8 2f da 00 00 callq ffffffff81051c50 <pid_vnr> + ffffffff81044221: 5d pop %rbp + ffffffff81044222: 48 98 cltq + ffffffff81044224: c3 retq + ffffffff81044225: 48 c7 c7 13 53 98 81 mov $0xffffffff81985313,%rdi + ffffffff8104422c: 31 c0 xor %eax,%eax + ffffffff8104422e: e8 60 0f 6d 00 callq ffffffff81715193 <printk> + ffffffff81044233: eb c9 jmp ffffffff810441fe <sys_getppid+0xe> + ffffffff81044235: 66 66 2e 0f 1f 84 00 data32 nopw %cs:0x0(%rax,%rax,1) + ffffffff8104423c: 00 00 00 00 Thus, the disable jump label case adds a 'mov', 'test' and 'jne' instruction vs. the jump label case just has a 'no-op' or 'jmp 0'. (The jmp 0, is patched to a 5 byte atomic no-op instruction at boot-time.) Thus, the disabled jump -label case adds: +label case adds:: -6 (mov) + 2 (test) + 2 (jne) = 10 - 5 (5 byte jump 0) = 5 addition bytes. + 6 (mov) + 2 (test) + 2 (jne) = 10 - 5 (5 byte jump 0) = 5 addition bytes. If we then include the padding bytes, the jump label code saves, 16 total bytes of instruction memory for this small function. In this case the non-jump label @@ -262,7 +271,7 @@ Since there are a number of static key API uses in the scheduler paths, 'pipe-test' (also known as 'perf bench sched pipe') can be used to show the performance improvement. Testing done on 3.3.0-rc2: -jump label disabled: +jump label disabled:: Performance counter stats for 'bash -c /tmp/pipe-test' (50 runs): @@ -279,7 +288,7 @@ jump label disabled: 1.601607384 seconds time elapsed ( +- 0.07% ) -jump label enabled: +jump label enabled:: Performance counter stats for 'bash -c /tmp/pipe-test' (50 runs): diff --git a/Documentation/svga.txt b/Documentation/svga.txt index cd66ec836e4f..119f1515b1ac 100644 --- a/Documentation/svga.txt +++ b/Documentation/svga.txt @@ -1,24 +1,31 @@ - Video Mode Selection Support 2.13 - (c) 1995--1999 Martin Mares, <mj@ucw.cz> --------------------------------------------------------------------------------- +.. include:: <isonum.txt> -1. Intro -~~~~~~~~ - This small document describes the "Video Mode Selection" feature which +================================= +Video Mode Selection Support 2.13 +================================= + +:Copyright: |copy| 1995--1999 Martin Mares, <mj@ucw.cz> + +Intro +~~~~~ + +This small document describes the "Video Mode Selection" feature which allows the use of various special video modes supported by the video BIOS. Due to usage of the BIOS, the selection is limited to boot time (before the kernel decompression starts) and works only on 80X86 machines. - ** Short intro for the impatient: Just use vga=ask for the first time, - ** enter `scan' on the video mode prompt, pick the mode you want to use, - ** remember its mode ID (the four-digit hexadecimal number) and then - ** set the vga parameter to this number (converted to decimal first). +.. note:: - The video mode to be used is selected by a kernel parameter which can be + Short intro for the impatient: Just use vga=ask for the first time, + enter ``scan`` on the video mode prompt, pick the mode you want to use, + remember its mode ID (the four-digit hexadecimal number) and then + set the vga parameter to this number (converted to decimal first). + +The video mode to be used is selected by a kernel parameter which can be specified in the kernel Makefile (the SVGA_MODE=... line) or by the "vga=..." option of LILO (or some other boot loader you use) or by the "vidmode" utility (present in standard Linux utility packages). You can use the following values -of this parameter: +of this parameter:: NORMAL_VGA - Standard 80x25 mode available on all display adapters. @@ -37,77 +44,79 @@ of this parameter: for exact meaning of the ID). Warning: rdev and LILO don't support hexadecimal numbers -- you have to convert it to decimal manually. -2. Menu -~~~~~~~ - The ASK_VGA mode causes the kernel to offer a video mode menu upon +Menu +~~~~ + +The ASK_VGA mode causes the kernel to offer a video mode menu upon bootup. It displays a "Press <RETURN> to see video modes available, <SPACE> to continue or wait 30 secs" message. If you press <RETURN>, you enter the menu, if you press <SPACE> or wait 30 seconds, the kernel will boot up in the standard 80x25 mode. - The menu looks like: +The menu looks like:: -Video adapter: <name-of-detected-video-adapter> -Mode: COLSxROWS: -0 0F00 80x25 -1 0F01 80x50 -2 0F02 80x43 -3 0F03 80x26 -.... -Enter mode number or `scan': <flashing-cursor-here> + Video adapter: <name-of-detected-video-adapter> + Mode: COLSxROWS: + 0 0F00 80x25 + 1 0F01 80x50 + 2 0F02 80x43 + 3 0F03 80x26 + .... + Enter mode number or ``scan``: <flashing-cursor-here> - <name-of-detected-video-adapter> tells what video adapter did Linux detect +<name-of-detected-video-adapter> tells what video adapter did Linux detect -- it's either a generic adapter name (MDA, CGA, HGC, EGA, VGA, VESA VGA [a VGA with VESA-compliant BIOS]) or a chipset name (e.g., Trident). Direct detection of chipsets is turned off by default (see CONFIG_VIDEO_SVGA in chapter 4 to see how to enable it if you really want) as it's inherently unreliable due to absolutely insane PC design. - "0 0F00 80x25" means that the first menu item (the menu items are numbered +"0 0F00 80x25" means that the first menu item (the menu items are numbered from "0" to "9" and from "a" to "z") is a 80x25 mode with ID=0x0f00 (see the next section for a description of mode IDs). - <flashing-cursor-here> encourages you to enter the item number or mode ID +<flashing-cursor-here> encourages you to enter the item number or mode ID you wish to set and press <RETURN>. If the computer complains something about "Unknown mode ID", it is trying to tell you that it isn't possible to set such a mode. It's also possible to press only <RETURN> which leaves the current mode. - The mode list usually contains a few basic modes and some VESA modes. In +The mode list usually contains a few basic modes and some VESA modes. In case your chipset has been detected, some chipset-specific modes are shown as well (some of these might be missing or unusable on your machine as different BIOSes are often shipped with the same card and the mode numbers depend purely on the VGA BIOS). - The modes displayed on the menu are partially sorted: The list starts with +The modes displayed on the menu are partially sorted: The list starts with the standard modes (80x25 and 80x50) followed by "special" modes (80x28 and 80x43), local modes (if the local modes feature is enabled), VESA modes and finally SVGA modes for the auto-detected adapter. - If you are not happy with the mode list offered (e.g., if you think your card +If you are not happy with the mode list offered (e.g., if you think your card is able to do more), you can enter "scan" instead of item number / mode ID. The program will try to ask the BIOS for all possible video mode numbers and test what happens then. The screen will be probably flashing wildly for some time and strange noises will be heard from inside the monitor and so on and then, really all consistent video modes supported by your BIOS will appear (plus maybe some -`ghost modes'). If you are afraid this could damage your monitor, don't use this -function. +``ghost modes``). If you are afraid this could damage your monitor, don't use +this function. - After scanning, the mode ordering is a bit different: the auto-detected SVGA -modes are not listed at all and the modes revealed by `scan' are shown before +After scanning, the mode ordering is a bit different: the auto-detected SVGA +modes are not listed at all and the modes revealed by ``scan`` are shown before all VESA modes. -3. Mode IDs -~~~~~~~~~~~ - Because of the complexity of all the video stuff, the video mode IDs +Mode IDs +~~~~~~~~ + +Because of the complexity of all the video stuff, the video mode IDs used here are also a bit complex. A video mode ID is a 16-bit number usually expressed in a hexadecimal notation (starting with "0x"). You can set a mode by entering its mode directly if you know it even if it isn't shown on the menu. -The ID numbers can be divided to three regions: +The ID numbers can be divided to those regions:: 0x0000 to 0x00ff - menu item references. 0x0000 is the first item. Don't use outside the menu as this can change from boot to boot (especially if you - have used the `scan' feature). + have used the ``scan`` feature). 0x0100 to 0x017f - standard BIOS modes. The ID is a BIOS video mode number (as presented to INT 10, function 00) increased by 0x0100. @@ -142,53 +151,54 @@ The ID numbers can be divided to three regions: 0xffff equivalent to 0x0f00 (standard 80x25) 0xfffe equivalent to 0x0f01 (EGA 80x43 or VGA 80x50) - If you add 0x8000 to the mode ID, the program will try to recalculate +If you add 0x8000 to the mode ID, the program will try to recalculate vertical display timing according to mode parameters, which can be used to eliminate some annoying bugs of certain VGA BIOSes (usually those used for cards with S3 chipsets and old Cirrus Logic BIOSes) -- mainly extra lines at the end of the display. -4. Options -~~~~~~~~~~ - Some options can be set in the source text (in arch/i386/boot/video.S). +Options +~~~~~~~ + +Some options can be set in the source text (in arch/i386/boot/video.S). All of them are simple #define's -- change them to #undef's when you want to switch them off. Currently supported: - CONFIG_VIDEO_SVGA - enables autodetection of SVGA cards. This is switched +CONFIG_VIDEO_SVGA - enables autodetection of SVGA cards. This is switched off by default as it's a bit unreliable due to terribly bad PC design. If you -really want to have the adapter autodetected (maybe in case the `scan' feature +really want to have the adapter autodetected (maybe in case the ``scan`` feature doesn't work on your machine), switch this on and don't cry if the results are not completely sane. In case you really need this feature, please drop me a mail as I think of removing it some day. - CONFIG_VIDEO_VESA - enables autodetection of VESA modes. If it doesn't work +CONFIG_VIDEO_VESA - enables autodetection of VESA modes. If it doesn't work on your machine (or displays a "Error: Scanning of VESA modes failed" message), you can switch it off and report as a bug. - CONFIG_VIDEO_COMPACT - enables compacting of the video mode list. If there +CONFIG_VIDEO_COMPACT - enables compacting of the video mode list. If there are more modes with the same screen size, only the first one is kept (see above for more info on mode ordering). However, in very strange cases it's possible that the first "version" of the mode doesn't work although some of the others do -- in this case turn this switch off to see the rest. - CONFIG_VIDEO_RETAIN - enables retaining of screen contents when switching +CONFIG_VIDEO_RETAIN - enables retaining of screen contents when switching video modes. Works only with some boot loaders which leave enough room for the buffer. (If you have old LILO, you can adjust heap_end_ptr and loadflags in setup.S, but it's better to upgrade the boot loader...) - CONFIG_VIDEO_LOCAL - enables inclusion of "local modes" in the list. The +CONFIG_VIDEO_LOCAL - enables inclusion of "local modes" in the list. The local modes are added automatically to the beginning of the list not depending on hardware configuration. The local modes are listed in the source text after the "local_mode_table:" line. The comment before this line describes the format of the table (which also includes a video card name to be displayed on the top of the menu). - CONFIG_VIDEO_400_HACK - force setting of 400 scan lines for standard VGA +CONFIG_VIDEO_400_HACK - force setting of 400 scan lines for standard VGA modes. This option is intended to be used on certain buggy BIOSes which draw some useless logo using font download and then fail to reset the correct mode. Don't use unless needed as it forces resetting the video card. - CONFIG_VIDEO_GFX_HACK - includes special hack for setting of graphics modes +CONFIG_VIDEO_GFX_HACK - includes special hack for setting of graphics modes to be used later by special drivers (e.g., 800x600 on IBM ThinkPad -- see ftp://ftp.phys.keio.ac.jp/pub/XFree86/800x600/XF86Configs/XF86Config.IBM_TP560). Allows to set _any_ BIOS mode including graphic ones and forcing specific @@ -196,33 +206,36 @@ text screen resolution instead of peeking it from BIOS variables. Don't use unless you think you know what you're doing. To activate this setup, use mode number 0x0f08 (see section 3). -5. Still doesn't work? -~~~~~~~~~~~~~~~~~~~~~~ - When the mode detection doesn't work (e.g., the mode list is incorrect or +Still doesn't work? +~~~~~~~~~~~~~~~~~~~ + +When the mode detection doesn't work (e.g., the mode list is incorrect or the machine hangs instead of displaying the menu), try to switch off some of the configuration options listed in section 4. If it fails, you can still use your kernel with the video mode set directly via the kernel parameter. - In either case, please send me a bug report containing what _exactly_ +In either case, please send me a bug report containing what _exactly_ happens and how do the configuration switches affect the behaviour of the bug. - If you start Linux from M$-DOS, you might also use some DOS tools for +If you start Linux from M$-DOS, you might also use some DOS tools for video mode setting. In this case, you must specify the 0x0f04 mode ("leave current settings") to Linux, because if you don't and you use any non-standard mode, Linux will switch to 80x25 automatically. - If you set some extended mode and there's one or more extra lines on the +If you set some extended mode and there's one or more extra lines on the bottom of the display containing already scrolled-out text, your VGA BIOS contains the most common video BIOS bug called "incorrect vertical display end setting". Adding 0x8000 to the mode ID might fix the problem. Unfortunately, this must be done manually -- no autodetection mechanisms are available. - If you have a VGA card and your display still looks as on EGA, your BIOS +If you have a VGA card and your display still looks as on EGA, your BIOS is probably broken and you need to set the CONFIG_VIDEO_400_HACK switch to force setting of the correct mode. -6. History -~~~~~~~~~~ +History +~~~~~~~ + +=============== ================================================================ 1.0 (??-Nov-95) First version supporting all adapters supported by the old setup.S + Cirrus Logic 54XX. Present in some 1.3.4? kernels and then removed due to instability on some machines. @@ -260,17 +273,18 @@ force setting of the correct mode. original version written by hhanemaa@cs.ruu.nl, patched by Jeff Chua, rewritten by me). - Screen store/restore fixed. -2.8 (14-Apr-96) - Previous release was not compilable without CONFIG_VIDEO_SVGA. +2.8 (14-Apr-96) - Previous release was not compilable without CONFIG_VIDEO_SVGA. - Better recognition of text modes during mode scan. 2.9 (12-May-96) - Ignored VESA modes 0x80 - 0xff (more VESA BIOS bugs!) -2.10 (11-Nov-96)- The whole thing made optional. +2.10(11-Nov-96) - The whole thing made optional. - Added the CONFIG_VIDEO_400_HACK switch. - Added the CONFIG_VIDEO_GFX_HACK switch. - Code cleanup. -2.11 (03-May-97)- Yet another cleanup, now including also the documentation. - - Direct testing of SVGA adapters turned off by default, `scan' +2.11(03-May-97) - Yet another cleanup, now including also the documentation. + - Direct testing of SVGA adapters turned off by default, ``scan`` offered explicitly on the prompt line. - Removed the doc section describing adding of new probing functions as I try to get rid of _all_ hardware probing here. -2.12 (25-May-98)- Added support for VESA frame buffer graphics. -2.13 (14-May-99)- Minor documentation fixes. +2.12(25-May-98) Added support for VESA frame buffer graphics. +2.13(14-May-99) Minor documentation fixes. +=============== ================================================================ diff --git a/Documentation/sysctl/vm.txt b/Documentation/sysctl/vm.txt index b4ad97f10b8e..48244c42ff52 100644 --- a/Documentation/sysctl/vm.txt +++ b/Documentation/sysctl/vm.txt @@ -240,6 +240,26 @@ fragmentation index is <= extfrag_threshold. The default value is 500. ============================================================== +highmem_is_dirtyable + +Available only for systems with CONFIG_HIGHMEM enabled (32b systems). + +This parameter controls whether the high memory is considered for dirty +writers throttling. This is not the case by default which means that +only the amount of memory directly visible/usable by the kernel can +be dirtied. As a result, on systems with a large amount of memory and +lowmem basically depleted writers might be throttled too early and +streaming writes can get very slow. + +Changing the value to non zero would allow more memory to be dirtied +and thus allow writers to write more data which can be flushed to the +storage more effectively. Note this also comes with a risk of pre-mature +OOM killer because some writers (e.g. direct block device writes) can +only use the low memory and they can fill it up with dirty data without +any throttling. + +============================================================== + hugepages_treat_as_movable This parameter controls whether we can allocate hugepages from ZONE_MOVABLE diff --git a/Documentation/tee.txt b/Documentation/tee.txt index 718599357596..56ea85ffebf2 100644 --- a/Documentation/tee.txt +++ b/Documentation/tee.txt @@ -1,4 +1,7 @@ +============= TEE subsystem +============= + This document describes the TEE subsystem in Linux. A TEE (Trusted Execution Environment) is a trusted OS running in some @@ -80,27 +83,27 @@ The GlobalPlatform TEE Client API [5] is implemented on top of the generic TEE API. Picture of the relationship between the different components in the -OP-TEE architecture. - - User space Kernel Secure world - ~~~~~~~~~~ ~~~~~~ ~~~~~~~~~~~~ - +--------+ +-------------+ - | Client | | Trusted | - +--------+ | Application | - /\ +-------------+ - || +----------+ /\ - || |tee- | || - || |supplicant| \/ - || +----------+ +-------------+ - \/ /\ | TEE Internal| - +-------+ || | API | - + TEE | || +--------+--------+ +-------------+ - | Client| || | TEE | OP-TEE | | OP-TEE | - | API | \/ | subsys | driver | | Trusted OS | - +-------+----------------+----+-------+----+-----------+-------------+ - | Generic TEE API | | OP-TEE MSG | - | IOCTL (TEE_IOC_*) | | SMCCC (OPTEE_SMC_CALL_*) | - +-----------------------------+ +------------------------------+ +OP-TEE architecture:: + + User space Kernel Secure world + ~~~~~~~~~~ ~~~~~~ ~~~~~~~~~~~~ + +--------+ +-------------+ + | Client | | Trusted | + +--------+ | Application | + /\ +-------------+ + || +----------+ /\ + || |tee- | || + || |supplicant| \/ + || +----------+ +-------------+ + \/ /\ | TEE Internal| + +-------+ || | API | + + TEE | || +--------+--------+ +-------------+ + | Client| || | TEE | OP-TEE | | OP-TEE | + | API | \/ | subsys | driver | | Trusted OS | + +-------+----------------+----+-------+----+-----------+-------------+ + | Generic TEE API | | OP-TEE MSG | + | IOCTL (TEE_IOC_*) | | SMCCC (OPTEE_SMC_CALL_*) | + +-----------------------------+ +------------------------------+ RPC (Remote Procedure Call) are requests from secure world to kernel driver or tee-supplicant. An RPC is identified by a special range of SMCCC return @@ -109,10 +112,16 @@ kernel are handled by the kernel driver. Other RPC messages will be forwarded to tee-supplicant without further involvement of the driver, except switching shared memory buffer representation. -References: +References +========== + [1] https://github.com/OP-TEE/optee_os + [2] http://infocenter.arm.com/help/topic/com.arm.doc.den0028a/index.html + [3] drivers/tee/optee/optee_smc.h + [4] drivers/tee/optee/optee_msg.h + [5] http://www.globalplatform.org/specificationsdevice.asp look for "TEE Client API Specification v1.0" and click download. diff --git a/Documentation/this_cpu_ops.txt b/Documentation/this_cpu_ops.txt index 2cbf71975381..5cb8b883ae83 100644 --- a/Documentation/this_cpu_ops.txt +++ b/Documentation/this_cpu_ops.txt @@ -1,5 +1,9 @@ +=================== this_cpu operations -------------------- +=================== + +:Author: Christoph Lameter, August 4th, 2014 +:Author: Pranith Kumar, Aug 2nd, 2014 this_cpu operations are a way of optimizing access to per cpu variables associated with the *currently* executing processor. This is @@ -39,7 +43,7 @@ operations. The following this_cpu() operations with implied preemption protection are defined. These operations can be used without worrying about -preemption and interrupts. +preemption and interrupts:: this_cpu_read(pcp) this_cpu_write(pcp, val) @@ -67,14 +71,14 @@ to relocate a per cpu relative address to the proper per cpu area for the processor. So the relocation to the per cpu base is encoded in the instruction via a segment register prefix. -For example: +For example:: DEFINE_PER_CPU(int, x); int z; z = this_cpu_read(x); -results in a single instruction +results in a single instruction:: mov ax, gs:[x] @@ -84,16 +88,16 @@ this_cpu_ops such sequence also required preempt disable/enable to prevent the kernel from moving the thread to a different processor while the calculation is performed. -Consider the following this_cpu operation: +Consider the following this_cpu operation:: this_cpu_inc(x) -The above results in the following single instruction (no lock prefix!) +The above results in the following single instruction (no lock prefix!):: inc gs:[x] instead of the following operations required if there is no segment -register: +register:: int *y; int cpu; @@ -121,8 +125,10 @@ has to be paid for this optimization is the need to add up the per cpu counters when the value of a counter is needed. -Special operations: -------------------- +Special operations +------------------ + +:: y = this_cpu_ptr(&x) @@ -153,11 +159,15 @@ Therefore the use of x or &x outside of the context of per cpu operations is invalid and will generally be treated like a NULL pointer dereference. +:: + DEFINE_PER_CPU(int, x); In the context of per cpu operations the above implies that x is a per cpu variable. Most this_cpu operations take a cpu variable. +:: + int __percpu *p = &x; &x and hence p is the *offset* of a per cpu variable. this_cpu_ptr() @@ -168,7 +178,7 @@ strange. Operations on a field of a per cpu structure -------------------------------------------- -Let's say we have a percpu structure +Let's say we have a percpu structure:: struct s { int n,m; @@ -177,14 +187,14 @@ Let's say we have a percpu structure DEFINE_PER_CPU(struct s, p); -Operations on these fields are straightforward +Operations on these fields are straightforward:: this_cpu_inc(p.m) z = this_cpu_cmpxchg(p.m, 0, 1); -If we have an offset to struct s: +If we have an offset to struct s:: struct s __percpu *ps = &p; @@ -194,7 +204,7 @@ If we have an offset to struct s: The calculation of the pointer may require the use of this_cpu_ptr() -if we do not make use of this_cpu ops later to manipulate fields: +if we do not make use of this_cpu ops later to manipulate fields:: struct s *pp; @@ -206,7 +216,7 @@ if we do not make use of this_cpu ops later to manipulate fields: Variants of this_cpu ops -------------------------- +------------------------ this_cpu ops are interrupt safe. Some architectures do not support these per cpu local operations. In that case the operation must be @@ -222,7 +232,7 @@ preemption. If a per cpu variable is not used in an interrupt context and the scheduler cannot preempt, then they are safe. If any interrupts still occur while an operation is in progress and if the interrupt too modifies the variable, then RMW actions can not be guaranteed to be -safe. +safe:: __this_cpu_read(pcp) __this_cpu_write(pcp, val) @@ -279,7 +289,7 @@ unless absolutely necessary. Please consider using an IPI to wake up the remote CPU and perform the update to its per cpu area. To access per-cpu data structure remotely, typically the per_cpu_ptr() -function is used: +function is used:: DEFINE_PER_CPU(struct data, datap); @@ -289,7 +299,7 @@ function is used: This makes it explicit that we are getting ready to access a percpu area remotely. -You can also do the following to convert the datap offset to an address +You can also do the following to convert the datap offset to an address:: struct data *p = this_cpu_ptr(&datap); @@ -305,7 +315,7 @@ the following scenario that occurs because two per cpu variables share a cache-line but the relaxed synchronization is applied to only one process updating the cache-line. -Consider the following example +Consider the following example:: struct test { @@ -327,6 +337,3 @@ mind that a remote write will evict the cache line from the processor that most likely will access it. If the processor wakes up and finds a missing local cache line of a per cpu area, its performance and hence the wake up times will be affected. - -Christoph Lameter, August 4th, 2014 -Pranith Kumar, Aug 2nd, 2014 diff --git a/Documentation/trace/ftrace.txt b/Documentation/trace/ftrace.txt index fff8ff6d4893..d4601df6e72e 100644 --- a/Documentation/trace/ftrace.txt +++ b/Documentation/trace/ftrace.txt @@ -5,10 +5,11 @@ Copyright 2008 Red Hat Inc. Author: Steven Rostedt <srostedt@redhat.com> License: The GNU Free Documentation License, Version 1.2 (dual licensed under the GPL v2) -Reviewers: Elias Oltmanns, Randy Dunlap, Andrew Morton, - John Kacur, and David Teigland. +Original Reviewers: Elias Oltmanns, Randy Dunlap, Andrew Morton, + John Kacur, and David Teigland. Written for: 2.6.28-rc2 Updated for: 3.10 +Updated for: 4.13 - Copyright 2017 VMware Inc. Steven Rostedt Introduction ------------ @@ -26,9 +27,11 @@ a task is woken to the task is actually scheduled in. One of the most common uses of ftrace is the event tracing. Through out the kernel is hundreds of static event points that -can be enabled via the debugfs file system to see what is +can be enabled via the tracefs file system to see what is going on in certain parts of the kernel. +See events.txt for more information. + Implementation Details ---------------------- @@ -39,34 +42,47 @@ See ftrace-design.txt for details for arch porters and such. The File System --------------- -Ftrace uses the debugfs file system to hold the control files as +Ftrace uses the tracefs file system to hold the control files as well as the files to display output. -When debugfs is configured into the kernel (which selecting any ftrace -option will do) the directory /sys/kernel/debug will be created. To mount +When tracefs is configured into the kernel (which selecting any ftrace +option will do) the directory /sys/kernel/tracing will be created. To mount this directory, you can add to your /etc/fstab file: - debugfs /sys/kernel/debug debugfs defaults 0 0 + tracefs /sys/kernel/tracing tracefs defaults 0 0 Or you can mount it at run time with: - mount -t debugfs nodev /sys/kernel/debug + mount -t tracefs nodev /sys/kernel/tracing For quicker access to that directory you may want to make a soft link to it: - ln -s /sys/kernel/debug /debug + ln -s /sys/kernel/tracing /tracing + + *** NOTICE *** + +Before 4.1, all ftrace tracing control files were within the debugfs +file system, which is typically located at /sys/kernel/debug/tracing. +For backward compatibility, when mounting the debugfs file system, +the tracefs file system will be automatically mounted at: + + /sys/kernel/debug/tracing -Any selected ftrace option will also create a directory called tracing -within the debugfs. The rest of the document will assume that you are in -the ftrace directory (cd /sys/kernel/debug/tracing) and will only concentrate -on the files within that directory and not distract from the content with -the extended "/sys/kernel/debug/tracing" path name. +All files located in the tracefs file system will be located in that +debugfs file system directory as well. + + *** NOTICE *** + +Any selected ftrace option will also create the tracefs file system. +The rest of the document will assume that you are in the ftrace directory +(cd /sys/kernel/tracing) and will only concentrate on the files within that +directory and not distract from the content with the extended +"/sys/kernel/tracing" path name. That's it! (assuming that you have ftrace configured into your kernel) -After mounting debugfs, you can see a directory called -"tracing". This directory contains the control and output files +After mounting tracefs you will have access to the control and output files of ftrace. Here is a list of some of the key files: @@ -92,10 +108,20 @@ of ftrace. Here is a list of some of the key files: writing to the ring buffer, the tracing overhead may still be occurring. + The kernel function tracing_off() can be used within the + kernel to disable writing to the ring buffer, which will + set this file to "0". User space can re-enable tracing by + echoing "1" into the file. + + Note, the function and event trigger "traceoff" will also + set this file to zero and stop tracing. Which can also + be re-enabled by user space using this file. + trace: This file holds the output of the trace in a human - readable format (described below). + readable format (described below). Note, tracing is temporarily + disabled while this file is being read (opened). trace_pipe: @@ -109,7 +135,8 @@ of ftrace. Here is a list of some of the key files: will not be read again with a sequential read. The "trace" file is static, and if the tracer is not adding more data, it will display the same - information every time it is read. + information every time it is read. This file will not + disable tracing while being read. trace_options: @@ -128,12 +155,14 @@ of ftrace. Here is a list of some of the key files: tracing_max_latency: Some of the tracers record the max latency. - For example, the time interrupts are disabled. - This time is saved in this file. The max trace - will also be stored, and displayed by "trace". - A new max trace will only be recorded if the - latency is greater than the value in this - file. (in microseconds) + For example, the maximum time that interrupts are disabled. + The maximum time is saved in this file. The max trace will also be + stored, and displayed by "trace". A new max trace will only be + recorded if the latency is greater than the value in this file + (in microseconds). + + By echoing in a time into this file, no latency will be recorded + unless it is greater than the time in this file. tracing_thresh: @@ -152,32 +181,34 @@ of ftrace. Here is a list of some of the key files: that the kernel uses for allocation, usually 4 KB in size). If the last page allocated has room for more bytes than requested, the rest of the page will be used, - making the actual allocation bigger than requested. + making the actual allocation bigger than requested or shown. ( Note, the size may not be a multiple of the page size due to buffer management meta-data. ) + Buffer sizes for individual CPUs may vary + (see "per_cpu/cpu0/buffer_size_kb" below), and if they do + this file will show "X". + buffer_total_size_kb: This displays the total combined size of all the trace buffers. free_buffer: - If a process is performing the tracing, and the ring buffer - should be shrunk "freed" when the process is finished, even - if it were to be killed by a signal, this file can be used - for that purpose. On close of this file, the ring buffer will - be resized to its minimum size. Having a process that is tracing - also open this file, when the process exits its file descriptor - for this file will be closed, and in doing so, the ring buffer - will be "freed". + If a process is performing tracing, and the ring buffer should be + shrunk "freed" when the process is finished, even if it were to be + killed by a signal, this file can be used for that purpose. On close + of this file, the ring buffer will be resized to its minimum size. + Having a process that is tracing also open this file, when the process + exits its file descriptor for this file will be closed, and in doing so, + the ring buffer will be "freed". It may also stop tracing if disable_on_free option is set. tracing_cpumask: - This is a mask that lets the user only trace - on specified CPUs. The format is a hex string - representing the CPUs. + This is a mask that lets the user only trace on specified CPUs. + The format is a hex string representing the CPUs. set_ftrace_filter: @@ -190,6 +221,9 @@ of ftrace. Here is a list of some of the key files: to be traced. Echoing names of functions into this file will limit the trace to only those functions. + The functions listed in "available_filter_functions" are what + can be written into this file. + This interface also allows for commands to be used. See the "Filter commands" section for more details. @@ -202,7 +236,14 @@ of ftrace. Here is a list of some of the key files: set_ftrace_pid: - Have the function tracer only trace a single thread. + Have the function tracer only trace the threads whose PID are + listed in this file. + + If the "function-fork" option is set, then when a task whose + PID is listed in this file forks, the child's PID will + automatically be added to this file, and the child will be + traced by the function tracer as well. This option will also + cause PIDs of tasks that exit to be removed from the file. set_event_pid: @@ -217,17 +258,28 @@ of ftrace. Here is a list of some of the key files: set_graph_function: - Set a "trigger" function where tracing should start - with the function graph tracer (See the section - "dynamic ftrace" for more details). + Functions listed in this file will cause the function graph + tracer to only trace these functions and the functions that + they call. (See the section "dynamic ftrace" for more details). + + set_graph_notrace: + + Similar to set_graph_function, but will disable function graph + tracing when the function is hit until it exits the function. + This makes it possible to ignore tracing functions that are called + by a specific function. available_filter_functions: - This lists the functions that ftrace - has processed and can trace. These are the function - names that you can pass to "set_ftrace_filter" or - "set_ftrace_notrace". (See the section "dynamic ftrace" - below for more details.) + This lists the functions that ftrace has processed and can trace. + These are the function names that you can pass to + "set_ftrace_filter" or "set_ftrace_notrace". + (See the section "dynamic ftrace" below for more details.) + + dyn_ftrace_total_info: + + This file is for debugging purposes. The number of functions that + have been converted to nops and are available to be traced. enabled_functions: @@ -250,12 +302,21 @@ of ftrace. Here is a list of some of the key files: an 'I' will be displayed on the same line as the function that can be overridden. + If the architecture supports it, it will also show what callback + is being directly called by the function. If the count is greater + than 1 it most likely will be ftrace_ops_list_func(). + + If the callback of the function jumps to a trampoline that is + specific to a the callback and not the standard trampoline, + its address will be printed as well as the function that the + trampoline calls. + function_profile_enabled: When set it will enable all functions with either the function - tracer, or if enabled, the function graph tracer. It will + tracer, or if configured, the function graph tracer. It will keep a histogram of the number of functions that were called - and if run with the function graph tracer, it will also keep + and if the function graph tracer was configured, it will also keep track of the time spent in those functions. The histogram content can be displayed in the files: @@ -283,12 +344,11 @@ of ftrace. Here is a list of some of the key files: printk_formats: This is for tools that read the raw format files. If an event in - the ring buffer references a string (currently only trace_printk() - does this), only a pointer to the string is recorded into the buffer - and not the string itself. This prevents tools from knowing what - that string was. This file displays the string and address for - the string allowing tools to map the pointers to what the - strings were. + the ring buffer references a string, only a pointer to the string + is recorded into the buffer and not the string itself. This prevents + tools from knowing what that string was. This file displays the string + and address for the string allowing tools to map the pointers to what + the strings were. saved_cmdlines: @@ -298,6 +358,22 @@ of ftrace. Here is a list of some of the key files: comms for events. If a pid for a comm is not listed, then "<...>" is displayed in the output. + If the option "record-cmd" is set to "0", then comms of tasks + will not be saved during recording. By default, it is enabled. + + saved_cmdlines_size: + + By default, 128 comms are saved (see "saved_cmdlines" above). To + increase or decrease the amount of comms that are cached, echo + in a the number of comms to cache, into this file. + + saved_tgids: + + If the option "record-tgid" is set, on each scheduling context switch + the Task Group ID of a task is saved in a table mapping the PID of + the thread to its TGID. By default, the "record-tgid" option is + disabled. + snapshot: This displays the "snapshot" buffer and also lets the user @@ -336,6 +412,9 @@ of ftrace. Here is a list of some of the key files: # cat trace_clock [local] global counter x86-tsc + The clock with the square brackets around it is the one + in effect. + local: Default clock, but may not be in sync across CPUs global: This clock is in sync with all CPUs but may @@ -448,6 +527,23 @@ of ftrace. Here is a list of some of the key files: See events.txt for more information. + set_event: + + By echoing in the event into this file, will enable that event. + + See events.txt for more information. + + available_events: + + A list of events that can be enabled in tracing. + + See events.txt for more information. + + hwlat_detector: + + Directory for the Hardware Latency Detector. + See "Hardware Latency Detector" section below. + per_cpu: This is a directory that contains the trace per_cpu information. @@ -539,13 +635,25 @@ Here is the list of current tracers that may be configured. to draw a graph of function calls similar to C code source. + "blk" + + The block tracer. The tracer used by the blktrace user + application. + + "hwlat" + + The Hardware Latency tracer is used to detect if the hardware + produces any latency. See "Hardware Latency Detector" section + below. + "irqsoff" Traces the areas that disable interrupts and saves the trace with the longest max latency. See tracing_max_latency. When a new max is recorded, it replaces the old trace. It is best to view this - trace with the latency-format option enabled. + trace with the latency-format option enabled, which + happens automatically when the tracer is selected. "preemptoff" @@ -571,6 +679,26 @@ Here is the list of current tracers that may be configured. RT tasks (as the current "wakeup" does). This is useful for those interested in wake up timings of RT tasks. + "wakeup_dl" + + Traces and records the max latency that it takes for + a SCHED_DEADLINE task to be woken (as the "wakeup" and + "wakeup_rt" does). + + "mmiotrace" + + A special tracer that is used to trace binary module. + It will trace all the calls that a module makes to the + hardware. Everything it writes and reads from the I/O + as well. + + "branch" + + This tracer can be configured when tracing likely/unlikely + calls within the kernel. It will trace when a likely and + unlikely branch is hit and if it was correct in its prediction + of being correct. + "nop" This is the "trace nothing" tracer. To remove all @@ -582,7 +710,7 @@ Examples of using the tracer ---------------------------- Here are typical examples of using the tracers when controlling -them only with the debugfs interface (without using any +them only with the tracefs interface (without using any user-land utilities). Output format: @@ -674,7 +802,7 @@ why a latency happened. Here is a typical trace. This shows that the current tracer is "irqsoff" tracing the time for which interrupts were disabled. It gives the trace version (which never changes) and the version of the kernel upon which this was executed on -(3.10). Then it displays the max latency in microseconds (259 us). The number +(3.8). Then it displays the max latency in microseconds (259 us). The number of trace entries displayed and the total number (both are four: #4/4). VP, KP, SP, and HP are always zero and are reserved for later use. #P is the number of online CPUs (#P:4). @@ -709,6 +837,8 @@ explains which is which. '.' otherwise. hardirq/softirq: + 'Z' - NMI occurred inside a hardirq + 'z' - NMI is running 'H' - hard irq occurred inside a softirq. 'h' - hard irq is running 's' - soft irq is running @@ -757,24 +887,24 @@ nohex nobin noblock trace_printk -nobranch annotate nouserstacktrace nosym-userobj noprintk-msg-only context-info nolatency-format -sleep-time -graph-time record-cmd +norecord-tgid overwrite nodisable_on_free irq-info markers noevent-fork function-trace +nofunction-fork nodisplay-graph nostacktrace +nobranch To disable one of the options, echo in the option prepended with "no". @@ -830,8 +960,6 @@ Here are the available options: trace_printk - Can disable trace_printk() from writing into the buffer. - branch - Enable branch tracing with the tracer. - annotate - It is sometimes confusing when the CPU buffers are full and one CPU buffer had a lot of events recently, thus a shorter time frame, were another CPU may have only had @@ -850,7 +978,8 @@ Here are the available options: <idle>-0 [001] .Ns3 21169.031485: sub_preempt_count <-_raw_spin_unlock userstacktrace - This option changes the trace. It records a - stacktrace of the current userspace thread. + stacktrace of the current user space thread after + each trace event. sym-userobj - when user stacktrace are enabled, look up which object the address belongs to, and print a @@ -873,29 +1002,21 @@ x494] <- /root/a.out[+0x4a8] <- /lib/libc-2.7.so[+0x1e1a6] context-info - Show only the event data. Hides the comm, PID, timestamp, CPU, and other useful data. - latency-format - This option changes the trace. When - it is enabled, the trace displays - additional information about the - latencies, as described in "Latency - trace format". - - sleep-time - When running function graph tracer, to include - the time a task schedules out in its function. - When enabled, it will account time the task has been - scheduled out as part of the function call. - - graph-time - When running function profiler with function graph tracer, - to include the time to call nested functions. When this is - not set, the time reported for the function will only - include the time the function itself executed for, not the - time for functions that it called. + latency-format - This option changes the trace output. When it is enabled, + the trace displays additional information about the + latency, as described in "Latency trace format". record-cmd - When any event or tracer is enabled, a hook is enabled - in the sched_switch trace point to fill comm cache + in the sched_switch trace point to fill comm cache with mapped pids and comms. But this may cause some overhead, and if you only care about pids, and not the name of the task, disabling this option can lower the - impact of tracing. + impact of tracing. See "saved_cmdlines". + + record-tgid - When any event or tracer is enabled, a hook is enabled + in the sched_switch trace point to fill the cache of + mapped Thread Group IDs (TGID) mapping to pids. See + "saved_tgids". overwrite - This controls what happens when the trace buffer is full. If "1" (default), the oldest events are @@ -935,19 +1056,98 @@ x494] <- /root/a.out[+0x4a8] <- /lib/libc-2.7.so[+0x1e1a6] functions. This keeps the overhead of the tracer down when performing latency tests. + function-fork - When set, tasks with PIDs listed in set_ftrace_pid will + have the PIDs of their children added to set_ftrace_pid + when those tasks fork. Also, when tasks with PIDs in + set_ftrace_pid exit, their PIDs will be removed from the + file. + display-graph - When set, the latency tracers (irqsoff, wakeup, etc) will use function graph tracing instead of function tracing. - stacktrace - This is one of the options that changes the trace - itself. When a trace is recorded, so is the stack - of functions. This allows for back traces of - trace sites. + stacktrace - When set, a stack trace is recorded after any trace event + is recorded. + + branch - Enable branch tracing with the tracer. This enables branch + tracer along with the currently set tracer. Enabling this + with the "nop" tracer is the same as just enabling the + "branch" tracer. Note: Some tracers have their own options. They only appear in this file when the tracer is active. They always appear in the options directory. +Here are the per tracer options: + +Options for function tracer: + + func_stack_trace - When set, a stack trace is recorded after every + function that is recorded. NOTE! Limit the functions + that are recorded before enabling this, with + "set_ftrace_filter" otherwise the system performance + will be critically degraded. Remember to disable + this option before clearing the function filter. + +Options for function_graph tracer: + + Since the function_graph tracer has a slightly different output + it has its own options to control what is displayed. + + funcgraph-overrun - When set, the "overrun" of the graph stack is + displayed after each function traced. The + overrun, is when the stack depth of the calls + is greater than what is reserved for each task. + Each task has a fixed array of functions to + trace in the call graph. If the depth of the + calls exceeds that, the function is not traced. + The overrun is the number of functions missed + due to exceeding this array. + + funcgraph-cpu - When set, the CPU number of the CPU where the trace + occurred is displayed. + + funcgraph-overhead - When set, if the function takes longer than + A certain amount, then a delay marker is + displayed. See "delay" above, under the + header description. + + funcgraph-proc - Unlike other tracers, the process' command line + is not displayed by default, but instead only + when a task is traced in and out during a context + switch. Enabling this options has the command + of each process displayed at every line. + + funcgraph-duration - At the end of each function (the return) + the duration of the amount of time in the + function is displayed in microseconds. + + funcgraph-abstime - When set, the timestamp is displayed at each + line. + + funcgraph-irqs - When disabled, functions that happen inside an + interrupt will not be traced. + + funcgraph-tail - When set, the return event will include the function + that it represents. By default this is off, and + only a closing curly bracket "}" is displayed for + the return of a function. + + sleep-time - When running function graph tracer, to include + the time a task schedules out in its function. + When enabled, it will account time the task has been + scheduled out as part of the function call. + + graph-time - When running function profiler with function graph tracer, + to include the time to call nested functions. When this is + not set, the time reported for the function will only + include the time the function itself executed for, not the + time for functions that it called. + +Options for blk tracer: + + blk_classic - Shows a more minimalistic output. + irqsoff ------- @@ -1711,6 +1911,85 @@ events. <idle>-0 2d..3 6us : 0:120:R ==> [002] 5882: 94:R sleep +Hardware Latency Detector +------------------------- + +The hardware latency detector is executed by enabling the "hwlat" tracer. + +NOTE, this tracer will affect the performance of the system as it will +periodically make a CPU constantly busy with interrupts disabled. + + # echo hwlat > current_tracer + # sleep 100 + # cat trace +# tracer: hwlat +# +# _-----=> irqs-off +# / _----=> need-resched +# | / _---=> hardirq/softirq +# || / _--=> preempt-depth +# ||| / delay +# TASK-PID CPU# |||| TIMESTAMP FUNCTION +# | | | |||| | | + <...>-3638 [001] d... 19452.055471: #1 inner/outer(us): 12/14 ts:1499801089.066141940 + <...>-3638 [003] d... 19454.071354: #2 inner/outer(us): 11/9 ts:1499801091.082164365 + <...>-3638 [002] dn.. 19461.126852: #3 inner/outer(us): 12/9 ts:1499801098.138150062 + <...>-3638 [001] d... 19488.340960: #4 inner/outer(us): 8/12 ts:1499801125.354139633 + <...>-3638 [003] d... 19494.388553: #5 inner/outer(us): 8/12 ts:1499801131.402150961 + <...>-3638 [003] d... 19501.283419: #6 inner/outer(us): 0/12 ts:1499801138.297435289 nmi-total:4 nmi-count:1 + + +The above output is somewhat the same in the header. All events will have +interrupts disabled 'd'. Under the FUNCTION title there is: + + #1 - This is the count of events recorded that were greater than the + tracing_threshold (See below). + + inner/outer(us): 12/14 + + This shows two numbers as "inner latency" and "outer latency". The test + runs in a loop checking a timestamp twice. The latency detected within + the two timestamps is the "inner latency" and the latency detected + after the previous timestamp and the next timestamp in the loop is + the "outer latency". + + ts:1499801089.066141940 + + The absolute timestamp that the event happened. + + nmi-total:4 nmi-count:1 + + On architectures that support it, if an NMI comes in during the + test, the time spent in NMI is reported in "nmi-total" (in + microseconds). + + All architectures that have NMIs will show the "nmi-count" if an + NMI comes in during the test. + +hwlat files: + + tracing_threshold - This gets automatically set to "10" to represent 10 + microseconds. This is the threshold of latency that + needs to be detected before the trace will be recorded. + + Note, when hwlat tracer is finished (another tracer is + written into "current_tracer"), the original value for + tracing_threshold is placed back into this file. + + hwlat_detector/width - The length of time the test runs with interrupts + disabled. + + hwlat_detector/window - The length of time of the window which the test + runs. That is, the test will run for "width" + microseconds per "window" microseconds + + tracing_cpumask - When the test is started. A kernel thread is created that + runs the test. This thread will alternate between CPUs + listed in the tracing_cpumask between each period + (one "window"). To limit the test to specific CPUs + set the mask in this file to only the CPUs that the test + should run on. + function -------- @@ -1821,15 +2100,15 @@ something like this simple program: #define STR(x) _STR(x) #define MAX_PATH 256 -const char *find_debugfs(void) +const char *find_tracefs(void) { - static char debugfs[MAX_PATH+1]; - static int debugfs_found; + static char tracefs[MAX_PATH+1]; + static int tracefs_found; char type[100]; FILE *fp; - if (debugfs_found) - return debugfs; + if (tracefs_found) + return tracefs; if ((fp = fopen("/proc/mounts","r")) == NULL) { perror("/proc/mounts"); @@ -1839,27 +2118,27 @@ const char *find_debugfs(void) while (fscanf(fp, "%*s %" STR(MAX_PATH) "s %99s %*s %*d %*d\n", - debugfs, type) == 2) { - if (strcmp(type, "debugfs") == 0) + tracefs, type) == 2) { + if (strcmp(type, "tracefs") == 0) break; } fclose(fp); - if (strcmp(type, "debugfs") != 0) { - fprintf(stderr, "debugfs not mounted"); + if (strcmp(type, "tracefs") != 0) { + fprintf(stderr, "tracefs not mounted"); return NULL; } - strcat(debugfs, "/tracing/"); - debugfs_found = 1; + strcat(tracefs, "/tracing/"); + tracefs_found = 1; - return debugfs; + return tracefs; } const char *tracing_file(const char *file_name) { static char trace_file[MAX_PATH+1]; - snprintf(trace_file, MAX_PATH, "%s/%s", find_debugfs(), file_name); + snprintf(trace_file, MAX_PATH, "%s/%s", find_tracefs(), file_name); return trace_file; } @@ -1898,12 +2177,12 @@ Or this simple script! ------ #!/bin/bash -debugfs=`sed -ne 's/^debugfs \(.*\) debugfs.*/\1/p' /proc/mounts` -echo nop > $debugfs/tracing/current_tracer -echo 0 > $debugfs/tracing/tracing_on -echo $$ > $debugfs/tracing/set_ftrace_pid -echo function > $debugfs/tracing/current_tracer -echo 1 > $debugfs/tracing/tracing_on +tracefs=`sed -ne 's/^tracefs \(.*\) tracefs.*/\1/p' /proc/mounts` +echo nop > $tracefs/tracing/current_tracer +echo 0 > $tracefs/tracing/tracing_on +echo $$ > $tracefs/tracing/set_ftrace_pid +echo function > $tracefs/tracing/current_tracer +echo 1 > $tracefs/tracing/tracing_on exec "$@" ------ @@ -2145,13 +2424,18 @@ include the -pg switch in the compiling of the kernel.) At compile time every C file object is run through the recordmcount program (located in the scripts directory). This program will parse the ELF headers in the C object to find all -the locations in the .text section that call mcount. (Note, only -white listed .text sections are processed, since processing other -sections like .init.text may cause races due to those sections -being freed unexpectedly). - -A new section called "__mcount_loc" is created that holds -references to all the mcount call sites in the .text section. +the locations in the .text section that call mcount. Starting +with gcc verson 4.6, the -mfentry has been added for x86, which +calls "__fentry__" instead of "mcount". Which is called before +the creation of the stack frame. + +Note, not all sections are traced. They may be prevented by either +a notrace, or blocked another way and all inline functions are not +traced. Check the "available_filter_functions" file to see what functions +can be traced. + +A section called "__mcount_loc" is created that holds +references to all the mcount/fentry call sites in the .text section. The recordmcount program re-links this section back into the original object. The final linking stage of the kernel will add all these references into a single table. @@ -2679,7 +2963,7 @@ in time without stopping tracing. Ftrace swaps the current buffer with a spare buffer, and tracing continues in the new current (=previous spare) buffer. -The following debugfs files in "tracing" are related to this +The following tracefs files in "tracing" are related to this feature: snapshot: @@ -2752,7 +3036,7 @@ cat: snapshot: Device or resource busy Instances --------- -In the debugfs tracing directory is a directory called "instances". +In the tracefs tracing directory is a directory called "instances". This directory can have new directories created inside of it using mkdir, and removing directories with rmdir. The directory created with mkdir in this directory will already contain files and other diff --git a/Documentation/translations/ko_KR/memory-barriers.txt b/Documentation/translations/ko_KR/memory-barriers.txt index c6f4ead76ce7..38310dcd6620 100644 --- a/Documentation/translations/ko_KR/memory-barriers.txt +++ b/Documentation/translations/ko_KR/memory-barriers.txt @@ -523,11 +523,11 @@ CPU ì—게 ê¸°ëŒ€í• ìˆ˜ 있는 ìµœì†Œí•œì˜ ë³´ìž¥ì‚¬í• ëª‡ê°€ì§€ê°€ 있습니 즉, ACQUIRE 는 ìµœì†Œí•œì˜ "ì·¨ë“" ë™ìž‘처럼, ê·¸ë¦¬ê³ RELEASE 는 ìµœì†Œí•œì˜ "공개" 처럼 ë™ìž‘한다는 ì˜ë¯¸ìž…니다. -atomic_ops.txt ì—ì„œ 설명ë˜ëŠ” ì–´í† ë¯¹ 오í¼ë ˆì´ì…˜ë“¤ 중ì—는 ì™„ì „ížˆ 순서잡힌 것들과 -(배리어를 사용하지 않는) ì™„í™”ëœ ìˆœì„œì˜ ê²ƒë“¤ ì™¸ì— ACQUIRE 와 RELEASE ë¶€ë¥˜ì˜ -ê²ƒë“¤ë„ ì¡´ìž¬í•©ë‹ˆë‹¤. 로드와 ìŠ¤í† ì–´ë¥¼ ëª¨ë‘ ìˆ˜í–‰í•˜ëŠ” ì¡°í•©ëœ ì–´í† ë¯¹ 오í¼ë ˆì´ì…˜ì—ì„œ, -ACQUIRE 는 해당 오í¼ë ˆì´ì…˜ì˜ 로드 부분ì—만 ì ìš©ë˜ê³ RELEASE 는 해당 -오í¼ë ˆì´ì…˜ì˜ ìŠ¤í† ì–´ 부분ì—만 ì ìš©ë©ë‹ˆë‹¤. +core-api/atomic_ops.rst ì—ì„œ 설명ë˜ëŠ” ì–´í† ë¯¹ 오í¼ë ˆì´ì…˜ë“¤ 중ì—는 ì™„ì „ížˆ +순서잡힌 것들과 (배리어를 사용하지 않는) ì™„í™”ëœ ìˆœì„œì˜ ê²ƒë“¤ ì™¸ì— ACQUIRE 와 +RELEASE ë¶€ë¥˜ì˜ ê²ƒë“¤ë„ ì¡´ìž¬í•©ë‹ˆë‹¤. 로드와 ìŠ¤í† ì–´ë¥¼ ëª¨ë‘ ìˆ˜í–‰í•˜ëŠ” ì¡°í•©ëœ ì–´í† ë¯¹ +오í¼ë ˆì´ì…˜ì—ì„œ, ACQUIRE 는 해당 오í¼ë ˆì´ì…˜ì˜ 로드 부분ì—만 ì ìš©ë˜ê³ RELEASE 는 +해당 오í¼ë ˆì´ì…˜ì˜ ìŠ¤í† ì–´ 부분ì—만 ì ìš©ë©ë‹ˆë‹¤. 메모리 ë°°ë¦¬ì–´ë“¤ì€ ë‘ CPU ê°„, ë˜ëŠ” CPU 와 디바ì´ìŠ¤ ê°„ì— ìƒí˜¸ìž‘ìš©ì˜ ê°€ëŠ¥ì„±ì´ ìžˆì„ ë•Œì—만 필요합니다. 만약 ì–´ë–¤ ì½”ë“œì— ê·¸ëŸ° ìƒí˜¸ìž‘ìš©ì´ ì—†ì„ ê²ƒì´ ë³´ìž¥ëœë‹¤ë©´, 해당 @@ -1848,7 +1848,7 @@ Mandatory ë°°ë¦¬ì–´ë“¤ì€ SMP 시스템ì—ì„œë„ UP 시스템ì—ì„œë„ SMP íš¨ê³ ì´ ì½”ë“œëŠ” ê°ì²´ì˜ ì—…ë°ì´íŠ¸ëœ death 마í¬ê°€ ë ˆí¼ëŸ°ìŠ¤ ì¹´ìš´í„° ê°ì†Œ ë™ìž‘ *ì „ì—* ë³´ì¼ ê²ƒì„ ë³´ìž¥í•©ë‹ˆë‹¤. - ë” ë§Žì€ ì •ë³´ë¥¼ ìœ„í•´ì„ Documentation/atomic_ops.txt 문서를 ì°¸ê³ í•˜ì„¸ìš”. + ë” ë§Žì€ ì •ë³´ë¥¼ ìœ„í•´ì„ Documentation/core-api/atomic_ops.rst 문서를 ì°¸ê³ í•˜ì„¸ìš”. 어디서 ì´ê²ƒë“¤ì„ 사용해야 í• ì§€ ê¶ê¸ˆí•˜ë‹¤ë©´ "ì–´í† ë¯¹ 오í¼ë ˆì´ì…˜" ì„œë¸Œì„¹ì…˜ì„ ì°¸ê³ í•˜ì„¸ìš”. @@ -2550,7 +2550,7 @@ CPU ì—서는 사용ë˜ëŠ” ì–´í† ë¯¹ ì¸ìŠ¤íŠ¸ëŸì…˜ ìžì²´ì— 메모리 배리ì 있는ë°, 그런 ê²½ìš°ì— ì´ íŠ¹ìˆ˜ 메모리 배리어 ë„êµ¬ë“¤ì€ no-op ì´ ë˜ì–´ 실질ì 으로 아무ì¼ë„ 하지 않습니다. -ë” ë§Žì€ ë‚´ìš©ì„ ìœ„í•´ì„ Documentation/atomic_ops.txt 를 ì°¸ê³ í•˜ì„¸ìš”. +ë” ë§Žì€ ë‚´ìš©ì„ ìœ„í•´ì„ Documentation/core-api/atomic_ops.rst 를 ì°¸ê³ í•˜ì„¸ìš”. 디바ì´ìŠ¤ 액세스 diff --git a/Documentation/unaligned-memory-access.txt b/Documentation/unaligned-memory-access.txt index 3f76c0c37920..51b4ff031586 100644 --- a/Documentation/unaligned-memory-access.txt +++ b/Documentation/unaligned-memory-access.txt @@ -1,6 +1,15 @@ +========================= UNALIGNED MEMORY ACCESSES ========================= +:Author: Daniel Drake <dsd@gentoo.org>, +:Author: Johannes Berg <johannes@sipsolutions.net> + +:With help from: Alan Cox, Avuton Olrich, Heikki Orsila, Jan Engelhardt, + Kyle McMartin, Kyle Moffett, Randy Dunlap, Robert Hancock, Uli Kunitz, + Vadim Lobanov + + Linux runs on a wide variety of architectures which have varying behaviour when it comes to memory access. This document presents some details about unaligned accesses, why you need to write code that doesn't cause them, @@ -73,7 +82,7 @@ memory addresses of certain variables, etc. Fortunately things are not too complex, as in most cases, the compiler ensures that things will work for you. For example, take the following -structure: +structure:: struct foo { u16 field1; @@ -106,7 +115,7 @@ On a related topic, with the above considerations in mind you may observe that you could reorder the fields in the structure in order to place fields where padding would otherwise be inserted, and hence reduce the overall resident memory size of structure instances. The optimal layout of the -above example is: +above example is:: struct foo { u32 field2; @@ -139,21 +148,21 @@ Code that causes unaligned access With the above in mind, let's move onto a real life example of a function that can cause an unaligned memory access. The following function taken from include/linux/etherdevice.h is an optimized routine to compare two -ethernet MAC addresses for equality. +ethernet MAC addresses for equality:: -bool ether_addr_equal(const u8 *addr1, const u8 *addr2) -{ -#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS + bool ether_addr_equal(const u8 *addr1, const u8 *addr2) + { + #ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS u32 fold = ((*(const u32 *)addr1) ^ (*(const u32 *)addr2)) | ((*(const u16 *)(addr1 + 4)) ^ (*(const u16 *)(addr2 + 4))); return fold == 0; -#else + #else const u16 *a = (const u16 *)addr1; const u16 *b = (const u16 *)addr2; return ((a[0] ^ b[0]) | (a[1] ^ b[1]) | (a[2] ^ b[2])) == 0; -#endif -} + #endif + } In the above function, when the hardware has efficient unaligned access capability, there is no issue with this code. But when the hardware isn't @@ -171,7 +180,8 @@ as it is a decent optimization for the cases when you can ensure alignment, which is true almost all of the time in ethernet networking context. -Here is another example of some code that could cause unaligned accesses: +Here is another example of some code that could cause unaligned accesses:: + void myfunc(u8 *data, u32 value) { [...] @@ -184,6 +194,7 @@ to an address that is not evenly divisible by 4. In summary, the 2 main scenarios where you may run into unaligned access problems involve: + 1. Casting variables to types of different lengths 2. Pointer arithmetic followed by access to at least 2 bytes of data @@ -195,7 +206,7 @@ The easiest way to avoid unaligned access is to use the get_unaligned() and put_unaligned() macros provided by the <asm/unaligned.h> header file. Going back to an earlier example of code that potentially causes unaligned -access: +access:: void myfunc(u8 *data, u32 value) { @@ -204,7 +215,7 @@ access: [...] } -To avoid the unaligned memory access, you would rewrite it as follows: +To avoid the unaligned memory access, you would rewrite it as follows:: void myfunc(u8 *data, u32 value) { @@ -215,7 +226,7 @@ To avoid the unaligned memory access, you would rewrite it as follows: } The get_unaligned() macro works similarly. Assuming 'data' is a pointer to -memory and you wish to avoid unaligned access, its usage is as follows: +memory and you wish to avoid unaligned access, its usage is as follows:: u32 value = get_unaligned((u32 *) data); @@ -245,18 +256,10 @@ For some ethernet hardware that cannot DMA to unaligned addresses like 4*n+2 or non-ethernet hardware, this can be a problem, and it is then required to copy the incoming frame into an aligned buffer. Because this is unnecessary on architectures that can do unaligned accesses, the code can be -made dependent on CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS like so: - -#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS - skb = original skb -#else - skb = copy skb -#endif - --- -Authors: Daniel Drake <dsd@gentoo.org>, - Johannes Berg <johannes@sipsolutions.net> -With help from: Alan Cox, Avuton Olrich, Heikki Orsila, Jan Engelhardt, -Kyle McMartin, Kyle Moffett, Randy Dunlap, Robert Hancock, Uli Kunitz, -Vadim Lobanov +made dependent on CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS like so:: + #ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS + skb = original skb + #else + skb = copy skb + #endif diff --git a/Documentation/vfio-mediated-device.txt b/Documentation/vfio-mediated-device.txt index e5e57b40f8af..1b3950346532 100644 --- a/Documentation/vfio-mediated-device.txt +++ b/Documentation/vfio-mediated-device.txt @@ -1,14 +1,17 @@ -/* - * VFIO Mediated devices - * - * Copyright (c) 2016, NVIDIA CORPORATION. All rights reserved. - * Author: Neo Jia <cjia@nvidia.com> - * Kirti Wankhede <kwankhede@nvidia.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ +.. include:: <isonum.txt> + +===================== +VFIO Mediated devices +===================== + +:Copyright: |copy| 2016, NVIDIA CORPORATION. All rights reserved. +:Author: Neo Jia <cjia@nvidia.com> +:Author: Kirti Wankhede <kwankhede@nvidia.com> + +This program is free software; you can redistribute it and/or modify +it under the terms of the GNU General Public License version 2 as +published by the Free Software Foundation. + Virtual Function I/O (VFIO) Mediated devices[1] =============================================== @@ -42,7 +45,7 @@ removes it from a VFIO group. The following high-level block diagram shows the main components and interfaces in the VFIO mediated driver framework. The diagram shows NVIDIA, Intel, and IBM -devices as examples, as these devices are the first devices to use this module. +devices as examples, as these devices are the first devices to use this module:: +---------------+ | | @@ -91,7 +94,7 @@ Registration Interface for a Mediated Bus Driver ------------------------------------------------ The registration interface for a mediated bus driver provides the following -structure to represent a mediated device's driver: +structure to represent a mediated device's driver:: /* * struct mdev_driver [2] - Mediated device's driver @@ -110,14 +113,14 @@ structure to represent a mediated device's driver: A mediated bus driver for mdev should use this structure in the function calls to register and unregister itself with the core driver: -* Register: +* Register:: - extern int mdev_register_driver(struct mdev_driver *drv, + extern int mdev_register_driver(struct mdev_driver *drv, struct module *owner); -* Unregister: +* Unregister:: - extern void mdev_unregister_driver(struct mdev_driver *drv); + extern void mdev_unregister_driver(struct mdev_driver *drv); The mediated bus driver is responsible for adding mediated devices to the VFIO group when devices are bound to the driver and removing mediated devices from @@ -152,15 +155,15 @@ The callbacks in the mdev_parent_ops structure are as follows: * mmap: mmap emulation callback A driver should use the mdev_parent_ops structure in the function call to -register itself with the mdev core driver: +register itself with the mdev core driver:: -extern int mdev_register_device(struct device *dev, - const struct mdev_parent_ops *ops); + extern int mdev_register_device(struct device *dev, + const struct mdev_parent_ops *ops); However, the mdev_parent_ops structure is not required in the function call -that a driver should use to unregister itself with the mdev core driver: +that a driver should use to unregister itself with the mdev core driver:: -extern void mdev_unregister_device(struct device *dev); + extern void mdev_unregister_device(struct device *dev); Mediated Device Management Interface Through sysfs @@ -183,30 +186,32 @@ with the mdev core driver. Directories and files under the sysfs for Each Physical Device -------------------------------------------------------------- -|- [parent physical device] -|--- Vendor-specific-attributes [optional] -|--- [mdev_supported_types] -| |--- [<type-id>] -| | |--- create -| | |--- name -| | |--- available_instances -| | |--- device_api -| | |--- description -| | |--- [devices] -| |--- [<type-id>] -| | |--- create -| | |--- name -| | |--- available_instances -| | |--- device_api -| | |--- description -| | |--- [devices] -| |--- [<type-id>] -| |--- create -| |--- name -| |--- available_instances -| |--- device_api -| |--- description -| |--- [devices] +:: + + |- [parent physical device] + |--- Vendor-specific-attributes [optional] + |--- [mdev_supported_types] + | |--- [<type-id>] + | | |--- create + | | |--- name + | | |--- available_instances + | | |--- device_api + | | |--- description + | | |--- [devices] + | |--- [<type-id>] + | | |--- create + | | |--- name + | | |--- available_instances + | | |--- device_api + | | |--- description + | | |--- [devices] + | |--- [<type-id>] + | |--- create + | |--- name + | |--- available_instances + | |--- device_api + | |--- description + | |--- [devices] * [mdev_supported_types] @@ -219,12 +224,12 @@ Directories and files under the sysfs for Each Physical Device The [<type-id>] name is created by adding the device driver string as a prefix to the string provided by the vendor driver. This format of this name is as - follows: + follows:: sprintf(buf, "%s-%s", dev_driver_string(parent->dev), group->name); (or using mdev_parent_dev(mdev) to arrive at the parent device outside - of the core mdev code) + of the core mdev code) * device_api @@ -239,7 +244,7 @@ Directories and files under the sysfs for Each Physical Device * [device] This directory contains links to the devices of type <type-id> that have been -created. + created. * name @@ -253,21 +258,25 @@ created. Directories and Files Under the sysfs for Each mdev Device ---------------------------------------------------------- -|- [parent phy device] -|--- [$MDEV_UUID] +:: + + |- [parent phy device] + |--- [$MDEV_UUID] |--- remove |--- mdev_type {link to its type} |--- vendor-specific-attributes [optional] * remove (write only) + Writing '1' to the 'remove' file destroys the mdev device. The vendor driver can fail the remove() callback if that device is active and the vendor driver doesn't support hot unplug. -Example: +Example:: + # echo 1 > /sys/bus/mdev/devices/$mdev_UUID/remove -Mediated device Hot plug: +Mediated device Hot plug ------------------------ Mediated devices can be created and assigned at runtime. The procedure to hot @@ -277,13 +286,13 @@ Translation APIs for Mediated Devices ===================================== The following APIs are provided for translating user pfn to host pfn in a VFIO -driver: +driver:: -extern int vfio_pin_pages(struct device *dev, unsigned long *user_pfn, - int npage, int prot, unsigned long *phys_pfn); + extern int vfio_pin_pages(struct device *dev, unsigned long *user_pfn, + int npage, int prot, unsigned long *phys_pfn); -extern int vfio_unpin_pages(struct device *dev, unsigned long *user_pfn, - int npage); + extern int vfio_unpin_pages(struct device *dev, unsigned long *user_pfn, + int npage); These functions call back into the back-end IOMMU module by using the pin_pages and unpin_pages callbacks of the struct vfio_iommu_driver_ops[4]. Currently @@ -304,81 +313,80 @@ card. This step creates a dummy device, /sys/devices/virtual/mtty/mtty/ - Files in this device directory in sysfs are similar to the following: - - # tree /sys/devices/virtual/mtty/mtty/ - /sys/devices/virtual/mtty/mtty/ - |-- mdev_supported_types - | |-- mtty-1 - | | |-- available_instances - | | |-- create - | | |-- device_api - | | |-- devices - | | `-- name - | `-- mtty-2 - | |-- available_instances - | |-- create - | |-- device_api - | |-- devices - | `-- name - |-- mtty_dev - | `-- sample_mtty_dev - |-- power - | |-- autosuspend_delay_ms - | |-- control - | |-- runtime_active_time - | |-- runtime_status - | `-- runtime_suspended_time - |-- subsystem -> ../../../../class/mtty - `-- uevent + Files in this device directory in sysfs are similar to the following:: + + # tree /sys/devices/virtual/mtty/mtty/ + /sys/devices/virtual/mtty/mtty/ + |-- mdev_supported_types + | |-- mtty-1 + | | |-- available_instances + | | |-- create + | | |-- device_api + | | |-- devices + | | `-- name + | `-- mtty-2 + | |-- available_instances + | |-- create + | |-- device_api + | |-- devices + | `-- name + |-- mtty_dev + | `-- sample_mtty_dev + |-- power + | |-- autosuspend_delay_ms + | |-- control + | |-- runtime_active_time + | |-- runtime_status + | `-- runtime_suspended_time + |-- subsystem -> ../../../../class/mtty + `-- uevent 2. Create a mediated device by using the dummy device that you created in the - previous step. + previous step:: - # echo "83b8f4f2-509f-382f-3c1e-e6bfe0fa1001" > \ + # echo "83b8f4f2-509f-382f-3c1e-e6bfe0fa1001" > \ /sys/devices/virtual/mtty/mtty/mdev_supported_types/mtty-2/create -3. Add parameters to qemu-kvm. +3. Add parameters to qemu-kvm:: - -device vfio-pci,\ - sysfsdev=/sys/bus/mdev/devices/83b8f4f2-509f-382f-3c1e-e6bfe0fa1001 + -device vfio-pci,\ + sysfsdev=/sys/bus/mdev/devices/83b8f4f2-509f-382f-3c1e-e6bfe0fa1001 4. Boot the VM. In the Linux guest VM, with no hardware on the host, the device appears - as follows: - - # lspci -s 00:05.0 -xxvv - 00:05.0 Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550]) - Subsystem: Device 4348:3253 - Physical Slot: 5 - Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- - Stepping- SERR- FastB2B- DisINTx- - Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- - <TAbort- <MAbort- >SERR- <PERR- INTx- - Interrupt: pin A routed to IRQ 10 - Region 0: I/O ports at c150 [size=8] - Region 1: I/O ports at c158 [size=8] - Kernel driver in use: serial - 00: 48 43 53 32 01 00 00 02 10 02 00 07 00 00 00 00 - 10: 51 c1 00 00 59 c1 00 00 00 00 00 00 00 00 00 00 - 20: 00 00 00 00 00 00 00 00 00 00 00 00 48 43 53 32 - 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00 - - In the Linux guest VM, dmesg output for the device is as follows: - - serial 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, high) -> IRQ -10 - 0000:00:05.0: ttyS1 at I/O 0xc150 (irq = 10) is a 16550A - 0000:00:05.0: ttyS2 at I/O 0xc158 (irq = 10) is a 16550A - - -5. In the Linux guest VM, check the serial ports. - - # setserial -g /dev/ttyS* - /dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4 - /dev/ttyS1, UART: 16550A, Port: 0xc150, IRQ: 10 - /dev/ttyS2, UART: 16550A, Port: 0xc158, IRQ: 10 + as follows:: + + # lspci -s 00:05.0 -xxvv + 00:05.0 Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550]) + Subsystem: Device 4348:3253 + Physical Slot: 5 + Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- + Stepping- SERR- FastB2B- DisINTx- + Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- + <TAbort- <MAbort- >SERR- <PERR- INTx- + Interrupt: pin A routed to IRQ 10 + Region 0: I/O ports at c150 [size=8] + Region 1: I/O ports at c158 [size=8] + Kernel driver in use: serial + 00: 48 43 53 32 01 00 00 02 10 02 00 07 00 00 00 00 + 10: 51 c1 00 00 59 c1 00 00 00 00 00 00 00 00 00 00 + 20: 00 00 00 00 00 00 00 00 00 00 00 00 48 43 53 32 + 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00 + + In the Linux guest VM, dmesg output for the device is as follows: + + serial 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, high) -> IRQ 10 + 0000:00:05.0: ttyS1 at I/O 0xc150 (irq = 10) is a 16550A + 0000:00:05.0: ttyS2 at I/O 0xc158 (irq = 10) is a 16550A + + +5. In the Linux guest VM, check the serial ports:: + + # setserial -g /dev/ttyS* + /dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4 + /dev/ttyS1, UART: 16550A, Port: 0xc150, IRQ: 10 + /dev/ttyS2, UART: 16550A, Port: 0xc158, IRQ: 10 6. Using minicom or any terminal emulation program, open port /dev/ttyS1 or /dev/ttyS2 with hardware flow control disabled. @@ -388,14 +396,14 @@ card. Data is loop backed from hosts mtty driver. -8. Destroy the mediated device that you created. +8. Destroy the mediated device that you created:: - # echo 1 > /sys/bus/mdev/devices/83b8f4f2-509f-382f-3c1e-e6bfe0fa1001/remove + # echo 1 > /sys/bus/mdev/devices/83b8f4f2-509f-382f-3c1e-e6bfe0fa1001/remove References ========== -[1] See Documentation/vfio.txt for more information on VFIO. -[2] struct mdev_driver in include/linux/mdev.h -[3] struct mdev_parent_ops in include/linux/mdev.h -[4] struct vfio_iommu_driver_ops in include/linux/vfio.h +1. See Documentation/vfio.txt for more information on VFIO. +2. struct mdev_driver in include/linux/mdev.h +3. struct mdev_parent_ops in include/linux/mdev.h +4. struct vfio_iommu_driver_ops in include/linux/vfio.h diff --git a/Documentation/vfio.txt b/Documentation/vfio.txt index 1dd3fddfd3a1..ef6a5111eaa1 100644 --- a/Documentation/vfio.txt +++ b/Documentation/vfio.txt @@ -1,5 +1,7 @@ -VFIO - "Virtual Function I/O"[1] -------------------------------------------------------------------------------- +================================== +VFIO - "Virtual Function I/O" [1]_ +================================== + Many modern system now provide DMA and interrupt remapping facilities to help ensure I/O devices behave within the boundaries they've been allotted. This includes x86 hardware with AMD-Vi and Intel VT-d, @@ -7,14 +9,14 @@ POWER systems with Partitionable Endpoints (PEs) and embedded PowerPC systems such as Freescale PAMU. The VFIO driver is an IOMMU/device agnostic framework for exposing direct device access to userspace, in a secure, IOMMU protected environment. In other words, this allows -safe[2], non-privileged, userspace drivers. +safe [2]_, non-privileged, userspace drivers. Why do we want that? Virtual machines often make use of direct device access ("device assignment") when configured for the highest possible I/O performance. From a device and host perspective, this simply turns the VM into a userspace driver, with the benefits of significantly reduced latency, higher bandwidth, and direct use of -bare-metal device drivers[3]. +bare-metal device drivers [3]_. Some applications, particularly in the high performance computing field, also benefit from low-overhead, direct device access from @@ -31,7 +33,7 @@ KVM PCI specific device assignment code as well as provide a more secure, more featureful userspace driver environment than UIO. Groups, Devices, and IOMMUs -------------------------------------------------------------------------------- +--------------------------- Devices are the main target of any I/O driver. Devices typically create a programming interface made up of I/O access, interrupts, @@ -114,40 +116,40 @@ well as mechanisms for describing and registering interrupt notifications. VFIO Usage Example -------------------------------------------------------------------------------- +------------------ -Assume user wants to access PCI device 0000:06:0d.0 +Assume user wants to access PCI device 0000:06:0d.0:: -$ readlink /sys/bus/pci/devices/0000:06:0d.0/iommu_group -../../../../kernel/iommu_groups/26 + $ readlink /sys/bus/pci/devices/0000:06:0d.0/iommu_group + ../../../../kernel/iommu_groups/26 This device is therefore in IOMMU group 26. This device is on the pci bus, therefore the user will make use of vfio-pci to manage the -group: +group:: -# modprobe vfio-pci + # modprobe vfio-pci Binding this device to the vfio-pci driver creates the VFIO group -character devices for this group: +character devices for this group:: -$ lspci -n -s 0000:06:0d.0 -06:0d.0 0401: 1102:0002 (rev 08) -# echo 0000:06:0d.0 > /sys/bus/pci/devices/0000:06:0d.0/driver/unbind -# echo 1102 0002 > /sys/bus/pci/drivers/vfio-pci/new_id + $ lspci -n -s 0000:06:0d.0 + 06:0d.0 0401: 1102:0002 (rev 08) + # echo 0000:06:0d.0 > /sys/bus/pci/devices/0000:06:0d.0/driver/unbind + # echo 1102 0002 > /sys/bus/pci/drivers/vfio-pci/new_id Now we need to look at what other devices are in the group to free -it for use by VFIO: - -$ ls -l /sys/bus/pci/devices/0000:06:0d.0/iommu_group/devices -total 0 -lrwxrwxrwx. 1 root root 0 Apr 23 16:13 0000:00:1e.0 -> - ../../../../devices/pci0000:00/0000:00:1e.0 -lrwxrwxrwx. 1 root root 0 Apr 23 16:13 0000:06:0d.0 -> - ../../../../devices/pci0000:00/0000:00:1e.0/0000:06:0d.0 -lrwxrwxrwx. 1 root root 0 Apr 23 16:13 0000:06:0d.1 -> - ../../../../devices/pci0000:00/0000:00:1e.0/0000:06:0d.1 - -This device is behind a PCIe-to-PCI bridge[4], therefore we also +it for use by VFIO:: + + $ ls -l /sys/bus/pci/devices/0000:06:0d.0/iommu_group/devices + total 0 + lrwxrwxrwx. 1 root root 0 Apr 23 16:13 0000:00:1e.0 -> + ../../../../devices/pci0000:00/0000:00:1e.0 + lrwxrwxrwx. 1 root root 0 Apr 23 16:13 0000:06:0d.0 -> + ../../../../devices/pci0000:00/0000:00:1e.0/0000:06:0d.0 + lrwxrwxrwx. 1 root root 0 Apr 23 16:13 0000:06:0d.1 -> + ../../../../devices/pci0000:00/0000:00:1e.0/0000:06:0d.1 + +This device is behind a PCIe-to-PCI bridge [4]_, therefore we also need to add device 0000:06:0d.1 to the group following the same procedure as above. Device 0000:00:1e.0 is a bridge that does not currently have a host driver, therefore it's not required to @@ -157,12 +159,12 @@ support PCI bridges). The final step is to provide the user with access to the group if unprivileged operation is desired (note that /dev/vfio/vfio provides no capabilities on its own and is therefore expected to be set to -mode 0666 by the system). +mode 0666 by the system):: -# chown user:user /dev/vfio/26 + # chown user:user /dev/vfio/26 The user now has full access to all the devices and the iommu for this -group and can access them as follows: +group and can access them as follows:: int container, group, device, i; struct vfio_group_status group_status = @@ -248,31 +250,31 @@ VFIO bus driver API VFIO bus drivers, such as vfio-pci make use of only a few interfaces into VFIO core. When devices are bound and unbound to the driver, the driver should call vfio_add_group_dev() and vfio_del_group_dev() -respectively: +respectively:: -extern int vfio_add_group_dev(struct iommu_group *iommu_group, - struct device *dev, - const struct vfio_device_ops *ops, - void *device_data); + extern int vfio_add_group_dev(struct iommu_group *iommu_group, + struct device *dev, + const struct vfio_device_ops *ops, + void *device_data); -extern void *vfio_del_group_dev(struct device *dev); + extern void *vfio_del_group_dev(struct device *dev); vfio_add_group_dev() indicates to the core to begin tracking the specified iommu_group and register the specified dev as owned by a VFIO bus driver. The driver provides an ops structure for callbacks -similar to a file operations structure: - -struct vfio_device_ops { - int (*open)(void *device_data); - void (*release)(void *device_data); - ssize_t (*read)(void *device_data, char __user *buf, - size_t count, loff_t *ppos); - ssize_t (*write)(void *device_data, const char __user *buf, - size_t size, loff_t *ppos); - long (*ioctl)(void *device_data, unsigned int cmd, - unsigned long arg); - int (*mmap)(void *device_data, struct vm_area_struct *vma); -}; +similar to a file operations structure:: + + struct vfio_device_ops { + int (*open)(void *device_data); + void (*release)(void *device_data); + ssize_t (*read)(void *device_data, char __user *buf, + size_t count, loff_t *ppos); + ssize_t (*write)(void *device_data, const char __user *buf, + size_t size, loff_t *ppos); + long (*ioctl)(void *device_data, unsigned int cmd, + unsigned long arg); + int (*mmap)(void *device_data, struct vm_area_struct *vma); + }; Each function is passed the device_data that was originally registered in the vfio_add_group_dev() call above. This allows the bus driver @@ -285,50 +287,55 @@ own VFIO_DEVICE_GET_REGION_INFO ioctl. PPC64 sPAPR implementation note -------------------------------------------------------------------------------- +------------------------------- This implementation has some specifics: 1) On older systems (POWER7 with P5IOC2/IODA1) only one IOMMU group per -container is supported as an IOMMU table is allocated at the boot time, -one table per a IOMMU group which is a Partitionable Endpoint (PE) -(PE is often a PCI domain but not always). -Newer systems (POWER8 with IODA2) have improved hardware design which allows -to remove this limitation and have multiple IOMMU groups per a VFIO container. + container is supported as an IOMMU table is allocated at the boot time, + one table per a IOMMU group which is a Partitionable Endpoint (PE) + (PE is often a PCI domain but not always). + + Newer systems (POWER8 with IODA2) have improved hardware design which allows + to remove this limitation and have multiple IOMMU groups per a VFIO + container. 2) The hardware supports so called DMA windows - the PCI address range -within which DMA transfer is allowed, any attempt to access address space -out of the window leads to the whole PE isolation. + within which DMA transfer is allowed, any attempt to access address space + out of the window leads to the whole PE isolation. 3) PPC64 guests are paravirtualized but not fully emulated. There is an API -to map/unmap pages for DMA, and it normally maps 1..32 pages per call and -currently there is no way to reduce the number of calls. In order to make things -faster, the map/unmap handling has been implemented in real mode which provides -an excellent performance which has limitations such as inability to do -locked pages accounting in real time. + to map/unmap pages for DMA, and it normally maps 1..32 pages per call and + currently there is no way to reduce the number of calls. In order to make + things faster, the map/unmap handling has been implemented in real mode + which provides an excellent performance which has limitations such as + inability to do locked pages accounting in real time. 4) According to sPAPR specification, A Partitionable Endpoint (PE) is an I/O -subtree that can be treated as a unit for the purposes of partitioning and -error recovery. A PE may be a single or multi-function IOA (IO Adapter), a -function of a multi-function IOA, or multiple IOAs (possibly including switch -and bridge structures above the multiple IOAs). PPC64 guests detect PCI errors -and recover from them via EEH RTAS services, which works on the basis of -additional ioctl commands. + subtree that can be treated as a unit for the purposes of partitioning and + error recovery. A PE may be a single or multi-function IOA (IO Adapter), a + function of a multi-function IOA, or multiple IOAs (possibly including + switch and bridge structures above the multiple IOAs). PPC64 guests detect + PCI errors and recover from them via EEH RTAS services, which works on the + basis of additional ioctl commands. -So 4 additional ioctls have been added: + So 4 additional ioctls have been added: - VFIO_IOMMU_SPAPR_TCE_GET_INFO - returns the size and the start - of the DMA window on the PCI bus. + VFIO_IOMMU_SPAPR_TCE_GET_INFO + returns the size and the start of the DMA window on the PCI bus. - VFIO_IOMMU_ENABLE - enables the container. The locked pages accounting + VFIO_IOMMU_ENABLE + enables the container. The locked pages accounting is done at this point. This lets user first to know what the DMA window is and adjust rlimit before doing any real job. - VFIO_IOMMU_DISABLE - disables the container. + VFIO_IOMMU_DISABLE + disables the container. - VFIO_EEH_PE_OP - provides an API for EEH setup, error detection and recovery. + VFIO_EEH_PE_OP + provides an API for EEH setup, error detection and recovery. -The code flow from the example above should be slightly changed: + The code flow from the example above should be slightly changed:: struct vfio_eeh_pe_op pe_op = { .argsz = sizeof(pe_op), .flags = 0 }; @@ -442,73 +449,73 @@ The code flow from the example above should be slightly changed: .... 5) There is v2 of SPAPR TCE IOMMU. It deprecates VFIO_IOMMU_ENABLE/ -VFIO_IOMMU_DISABLE and implements 2 new ioctls: -VFIO_IOMMU_SPAPR_REGISTER_MEMORY and VFIO_IOMMU_SPAPR_UNREGISTER_MEMORY -(which are unsupported in v1 IOMMU). + VFIO_IOMMU_DISABLE and implements 2 new ioctls: + VFIO_IOMMU_SPAPR_REGISTER_MEMORY and VFIO_IOMMU_SPAPR_UNREGISTER_MEMORY + (which are unsupported in v1 IOMMU). -PPC64 paravirtualized guests generate a lot of map/unmap requests, -and the handling of those includes pinning/unpinning pages and updating -mm::locked_vm counter to make sure we do not exceed the rlimit. -The v2 IOMMU splits accounting and pinning into separate operations: + PPC64 paravirtualized guests generate a lot of map/unmap requests, + and the handling of those includes pinning/unpinning pages and updating + mm::locked_vm counter to make sure we do not exceed the rlimit. + The v2 IOMMU splits accounting and pinning into separate operations: -- VFIO_IOMMU_SPAPR_REGISTER_MEMORY/VFIO_IOMMU_SPAPR_UNREGISTER_MEMORY ioctls -receive a user space address and size of the block to be pinned. -Bisecting is not supported and VFIO_IOMMU_UNREGISTER_MEMORY is expected to -be called with the exact address and size used for registering -the memory block. The userspace is not expected to call these often. -The ranges are stored in a linked list in a VFIO container. + - VFIO_IOMMU_SPAPR_REGISTER_MEMORY/VFIO_IOMMU_SPAPR_UNREGISTER_MEMORY ioctls + receive a user space address and size of the block to be pinned. + Bisecting is not supported and VFIO_IOMMU_UNREGISTER_MEMORY is expected to + be called with the exact address and size used for registering + the memory block. The userspace is not expected to call these often. + The ranges are stored in a linked list in a VFIO container. -- VFIO_IOMMU_MAP_DMA/VFIO_IOMMU_UNMAP_DMA ioctls only update the actual -IOMMU table and do not do pinning; instead these check that the userspace -address is from pre-registered range. + - VFIO_IOMMU_MAP_DMA/VFIO_IOMMU_UNMAP_DMA ioctls only update the actual + IOMMU table and do not do pinning; instead these check that the userspace + address is from pre-registered range. -This separation helps in optimizing DMA for guests. + This separation helps in optimizing DMA for guests. 6) sPAPR specification allows guests to have an additional DMA window(s) on -a PCI bus with a variable page size. Two ioctls have been added to support -this: VFIO_IOMMU_SPAPR_TCE_CREATE and VFIO_IOMMU_SPAPR_TCE_REMOVE. -The platform has to support the functionality or error will be returned to -the userspace. The existing hardware supports up to 2 DMA windows, one is -2GB long, uses 4K pages and called "default 32bit window"; the other can -be as big as entire RAM, use different page size, it is optional - guests -create those in run-time if the guest driver supports 64bit DMA. - -VFIO_IOMMU_SPAPR_TCE_CREATE receives a page shift, a DMA window size and -a number of TCE table levels (if a TCE table is going to be big enough and -the kernel may not be able to allocate enough of physically contiguous memory). -It creates a new window in the available slot and returns the bus address where -the new window starts. Due to hardware limitation, the user space cannot choose -the location of DMA windows. - -VFIO_IOMMU_SPAPR_TCE_REMOVE receives the bus start address of the window -and removes it. + a PCI bus with a variable page size. Two ioctls have been added to support + this: VFIO_IOMMU_SPAPR_TCE_CREATE and VFIO_IOMMU_SPAPR_TCE_REMOVE. + The platform has to support the functionality or error will be returned to + the userspace. The existing hardware supports up to 2 DMA windows, one is + 2GB long, uses 4K pages and called "default 32bit window"; the other can + be as big as entire RAM, use different page size, it is optional - guests + create those in run-time if the guest driver supports 64bit DMA. + + VFIO_IOMMU_SPAPR_TCE_CREATE receives a page shift, a DMA window size and + a number of TCE table levels (if a TCE table is going to be big enough and + the kernel may not be able to allocate enough of physically contiguous + memory). It creates a new window in the available slot and returns the bus + address where the new window starts. Due to hardware limitation, the user + space cannot choose the location of DMA windows. + + VFIO_IOMMU_SPAPR_TCE_REMOVE receives the bus start address of the window + and removes it. ------------------------------------------------------------------------------- -[1] VFIO was originally an acronym for "Virtual Function I/O" in its -initial implementation by Tom Lyon while as Cisco. We've since -outgrown the acronym, but it's catchy. - -[2] "safe" also depends upon a device being "well behaved". It's -possible for multi-function devices to have backdoors between -functions and even for single function devices to have alternative -access to things like PCI config space through MMIO registers. To -guard against the former we can include additional precautions in the -IOMMU driver to group multi-function PCI devices together -(iommu=group_mf). The latter we can't prevent, but the IOMMU should -still provide isolation. For PCI, SR-IOV Virtual Functions are the -best indicator of "well behaved", as these are designed for -virtualization usage models. - -[3] As always there are trade-offs to virtual machine device -assignment that are beyond the scope of VFIO. It's expected that -future IOMMU technologies will reduce some, but maybe not all, of -these trade-offs. - -[4] In this case the device is below a PCI bridge, so transactions -from either function of the device are indistinguishable to the iommu: - --[0000:00]-+-1e.0-[06]--+-0d.0 - \-0d.1 - -00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) +.. [1] VFIO was originally an acronym for "Virtual Function I/O" in its + initial implementation by Tom Lyon while as Cisco. We've since + outgrown the acronym, but it's catchy. + +.. [2] "safe" also depends upon a device being "well behaved". It's + possible for multi-function devices to have backdoors between + functions and even for single function devices to have alternative + access to things like PCI config space through MMIO registers. To + guard against the former we can include additional precautions in the + IOMMU driver to group multi-function PCI devices together + (iommu=group_mf). The latter we can't prevent, but the IOMMU should + still provide isolation. For PCI, SR-IOV Virtual Functions are the + best indicator of "well behaved", as these are designed for + virtualization usage models. + +.. [3] As always there are trade-offs to virtual machine device + assignment that are beyond the scope of VFIO. It's expected that + future IOMMU technologies will reduce some, but maybe not all, of + these trade-offs. + +.. [4] In this case the device is below a PCI bridge, so transactions + from either function of the device are indistinguishable to the iommu:: + + -[0000:00]-+-1e.0-[06]--+-0d.0 + \-0d.1 + + 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 3a9831b72945..e63a35fafef0 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -4329,3 +4329,21 @@ Querying this capability returns a bitmap indicating the possible virtual SMT modes that can be set using KVM_CAP_PPC_SMT. If bit N (counting from the right) is set, then a virtual SMT mode of 2^N is available. + +8.11 KVM_CAP_HYPERV_SYNIC2 + +Architectures: x86 + +This capability enables a newer version of Hyper-V Synthetic interrupt +controller (SynIC). The only difference with KVM_CAP_HYPERV_SYNIC is that KVM +doesn't clear SynIC message and event flags pages when they are enabled by +writing to the respective MSRs. + +8.12 KVM_CAP_HYPERV_VP_INDEX + +Architectures: x86 + +This capability indicates that userspace can load HV_X64_MSR_VP_INDEX msr. Its +value is used to denote the target vcpu for a SynIC interrupt. For +compatibilty, KVM initializes this msr to KVM's internal vcpu index. When this +capability is absent, userspace can still query this msr's value. diff --git a/Documentation/virtual/kvm/msr.txt b/Documentation/virtual/kvm/msr.txt index 0a9ea515512a..1ebecc115dc6 100644 --- a/Documentation/virtual/kvm/msr.txt +++ b/Documentation/virtual/kvm/msr.txt @@ -166,10 +166,11 @@ MSR_KVM_SYSTEM_TIME: 0x12 MSR_KVM_ASYNC_PF_EN: 0x4b564d02 data: Bits 63-6 hold 64-byte aligned physical address of a 64 byte memory area which must be in guest RAM and must be - zeroed. Bits 5-2 are reserved and should be zero. Bit 0 is 1 + zeroed. Bits 5-3 are reserved and should be zero. Bit 0 is 1 when asynchronous page faults are enabled on the vcpu 0 when disabled. Bit 1 is 1 if asynchronous page faults can be injected - when vcpu is in cpl == 0. + when vcpu is in cpl == 0. Bit 2 is 1 if asynchronous page faults + are delivered to L1 as #PF vmexits. First 4 byte of 64 byte memory location will be written to by the hypervisor at the time of asynchronous page fault (APF) diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt index 914518aeb972..b3526365ea8e 100644 --- a/Documentation/watchdog/watchdog-parameters.txt +++ b/Documentation/watchdog/watchdog-parameters.txt @@ -369,6 +369,12 @@ timeout: Watchdog timeout in seconds. (0<timeout<N, default=60) nowayout: Watchdog cannot be stopped once started (default=kernel config parameter) ------------------------------------------------- +uniphier_wdt: +timeout: Watchdog timeout in power of two seconds. + (1 <= timeout <= 128, default=64) +nowayout: Watchdog cannot be stopped once started + (default=kernel config parameter) +------------------------------------------------- w83627hf_wdt: wdt_io: w83627hf/thf WDT io port (default 0x2E) timeout: Watchdog timeout in seconds. 1 <= timeout <= 255, default=60. diff --git a/Documentation/xillybus.txt b/Documentation/xillybus.txt index 1660145b9969..2446ee303c09 100644 --- a/Documentation/xillybus.txt +++ b/Documentation/xillybus.txt @@ -1,12 +1,11 @@ +========================================== +Xillybus driver for generic FPGA interface +========================================== - ========================================== - Xillybus driver for generic FPGA interface - ========================================== +:Author: Eli Billauer, Xillybus Ltd. (http://xillybus.com) +:Email: eli.billauer@gmail.com or as advertised on Xillybus' site. -Author: Eli Billauer, Xillybus Ltd. (http://xillybus.com) -Email: eli.billauer@gmail.com or as advertised on Xillybus' site. - -Contents: +.. Contents: - Introduction -- Background @@ -17,7 +16,7 @@ Contents: -- Synchronization -- Seekable pipes -- Internals + - Internals -- Source code organization -- Pipe attributes -- Host never reads from the FPGA @@ -29,7 +28,7 @@ Contents: -- The "nonempty" message (supporting poll) -INTRODUCTION +Introduction ============ Background @@ -105,7 +104,7 @@ driver is used to work out of the box with any Xillybus IP core. The data structure just mentioned should not be confused with PCI's configuration space or the Flattened Device Tree. -USAGE +Usage ===== User interface @@ -117,11 +116,11 @@ names of these files depend on the IP core that is loaded in the FPGA (see Probing below). To communicate with the FPGA, open the device file that corresponds to the hardware FIFO you want to send data or receive data from, and use plain write() or read() calls, just like with a regular pipe. In -particular, it makes perfect sense to go: +particular, it makes perfect sense to go:: -$ cat mydata > /dev/xillybus_thisfifo + $ cat mydata > /dev/xillybus_thisfifo -$ cat /dev/xillybus_thatfifo > hisdata + $ cat /dev/xillybus_thatfifo > hisdata possibly pressing CTRL-C as some stage, even though the xillybus_* pipes have the capability to send an EOF (but may not use it). @@ -178,7 +177,7 @@ the attached memory is done by seeking to the desired address, and calling read() or write() as required. -INTERNALS +Internals ========= Source code organization @@ -365,7 +364,7 @@ into that page. It can be shown that all pages requested from the kernel (except possibly for the last) are 100% utilized this way. The "nonempty" message (supporting poll) ---------------------------------------- +---------------------------------------- In order to support the "poll" method (and hence select() ), there is a small catch regarding the FPGA to host direction: The FPGA may have filled a DMA diff --git a/Documentation/xz.txt b/Documentation/xz.txt index 2cf3e2608de3..b2220d03aa50 100644 --- a/Documentation/xz.txt +++ b/Documentation/xz.txt @@ -1,121 +1,127 @@ - +============================ XZ data compression in Linux ============================ Introduction +============ - XZ is a general purpose data compression format with high compression - ratio and relatively fast decompression. The primary compression - algorithm (filter) is LZMA2. Additional filters can be used to improve - compression ratio even further. E.g. Branch/Call/Jump (BCJ) filters - improve compression ratio of executable data. +XZ is a general purpose data compression format with high compression +ratio and relatively fast decompression. The primary compression +algorithm (filter) is LZMA2. Additional filters can be used to improve +compression ratio even further. E.g. Branch/Call/Jump (BCJ) filters +improve compression ratio of executable data. - The XZ decompressor in Linux is called XZ Embedded. It supports - the LZMA2 filter and optionally also BCJ filters. CRC32 is supported - for integrity checking. The home page of XZ Embedded is at - <http://tukaani.org/xz/embedded.html>, where you can find the - latest version and also information about using the code outside - the Linux kernel. +The XZ decompressor in Linux is called XZ Embedded. It supports +the LZMA2 filter and optionally also BCJ filters. CRC32 is supported +for integrity checking. The home page of XZ Embedded is at +<http://tukaani.org/xz/embedded.html>, where you can find the +latest version and also information about using the code outside +the Linux kernel. - For userspace, XZ Utils provide a zlib-like compression library - and a gzip-like command line tool. XZ Utils can be downloaded from - <http://tukaani.org/xz/>. +For userspace, XZ Utils provide a zlib-like compression library +and a gzip-like command line tool. XZ Utils can be downloaded from +<http://tukaani.org/xz/>. XZ related components in the kernel - - The xz_dec module provides XZ decompressor with single-call (buffer - to buffer) and multi-call (stateful) APIs. The usage of the xz_dec - module is documented in include/linux/xz.h. - - The xz_dec_test module is for testing xz_dec. xz_dec_test is not - useful unless you are hacking the XZ decompressor. xz_dec_test - allocates a char device major dynamically to which one can write - .xz files from userspace. The decompressed output is thrown away. - Keep an eye on dmesg to see diagnostics printed by xz_dec_test. - See the xz_dec_test source code for the details. - - For decompressing the kernel image, initramfs, and initrd, there - is a wrapper function in lib/decompress_unxz.c. Its API is the - same as in other decompress_*.c files, which is defined in - include/linux/decompress/generic.h. - - scripts/xz_wrap.sh is a wrapper for the xz command line tool found - from XZ Utils. The wrapper sets compression options to values suitable - for compressing the kernel image. - - For kernel makefiles, two commands are provided for use with - $(call if_needed). The kernel image should be compressed with - $(call if_needed,xzkern) which will use a BCJ filter and a big LZMA2 - dictionary. It will also append a four-byte trailer containing the - uncompressed size of the file, which is needed by the boot code. - Other things should be compressed with $(call if_needed,xzmisc) - which will use no BCJ filter and 1 MiB LZMA2 dictionary. +=================================== + +The xz_dec module provides XZ decompressor with single-call (buffer +to buffer) and multi-call (stateful) APIs. The usage of the xz_dec +module is documented in include/linux/xz.h. + +The xz_dec_test module is for testing xz_dec. xz_dec_test is not +useful unless you are hacking the XZ decompressor. xz_dec_test +allocates a char device major dynamically to which one can write +.xz files from userspace. The decompressed output is thrown away. +Keep an eye on dmesg to see diagnostics printed by xz_dec_test. +See the xz_dec_test source code for the details. + +For decompressing the kernel image, initramfs, and initrd, there +is a wrapper function in lib/decompress_unxz.c. Its API is the +same as in other decompress_*.c files, which is defined in +include/linux/decompress/generic.h. + +scripts/xz_wrap.sh is a wrapper for the xz command line tool found +from XZ Utils. The wrapper sets compression options to values suitable +for compressing the kernel image. + +For kernel makefiles, two commands are provided for use with +$(call if_needed). The kernel image should be compressed with +$(call if_needed,xzkern) which will use a BCJ filter and a big LZMA2 +dictionary. It will also append a four-byte trailer containing the +uncompressed size of the file, which is needed by the boot code. +Other things should be compressed with $(call if_needed,xzmisc) +which will use no BCJ filter and 1 MiB LZMA2 dictionary. Notes on compression options +============================ - Since the XZ Embedded supports only streams with no integrity check or - CRC32, make sure that you don't use some other integrity check type - when encoding files that are supposed to be decoded by the kernel. With - liblzma, you need to use either LZMA_CHECK_NONE or LZMA_CHECK_CRC32 - when encoding. With the xz command line tool, use --check=none or - --check=crc32. - - Using CRC32 is strongly recommended unless there is some other layer - which will verify the integrity of the uncompressed data anyway. - Double checking the integrity would probably be waste of CPU cycles. - Note that the headers will always have a CRC32 which will be validated - by the decoder; you can only change the integrity check type (or - disable it) for the actual uncompressed data. - - In userspace, LZMA2 is typically used with dictionary sizes of several - megabytes. The decoder needs to have the dictionary in RAM, thus big - dictionaries cannot be used for files that are intended to be decoded - by the kernel. 1 MiB is probably the maximum reasonable dictionary - size for in-kernel use (maybe more is OK for initramfs). The presets - in XZ Utils may not be optimal when creating files for the kernel, - so don't hesitate to use custom settings. Example: - - xz --check=crc32 --lzma2=dict=512KiB inputfile - - An exception to above dictionary size limitation is when the decoder - is used in single-call mode. Decompressing the kernel itself is an - example of this situation. In single-call mode, the memory usage - doesn't depend on the dictionary size, and it is perfectly fine to - use a big dictionary: for maximum compression, the dictionary should - be at least as big as the uncompressed data itself. +Since the XZ Embedded supports only streams with no integrity check or +CRC32, make sure that you don't use some other integrity check type +when encoding files that are supposed to be decoded by the kernel. With +liblzma, you need to use either LZMA_CHECK_NONE or LZMA_CHECK_CRC32 +when encoding. With the xz command line tool, use --check=none or +--check=crc32. + +Using CRC32 is strongly recommended unless there is some other layer +which will verify the integrity of the uncompressed data anyway. +Double checking the integrity would probably be waste of CPU cycles. +Note that the headers will always have a CRC32 which will be validated +by the decoder; you can only change the integrity check type (or +disable it) for the actual uncompressed data. + +In userspace, LZMA2 is typically used with dictionary sizes of several +megabytes. The decoder needs to have the dictionary in RAM, thus big +dictionaries cannot be used for files that are intended to be decoded +by the kernel. 1 MiB is probably the maximum reasonable dictionary +size for in-kernel use (maybe more is OK for initramfs). The presets +in XZ Utils may not be optimal when creating files for the kernel, +so don't hesitate to use custom settings. Example:: + + xz --check=crc32 --lzma2=dict=512KiB inputfile + +An exception to above dictionary size limitation is when the decoder +is used in single-call mode. Decompressing the kernel itself is an +example of this situation. In single-call mode, the memory usage +doesn't depend on the dictionary size, and it is perfectly fine to +use a big dictionary: for maximum compression, the dictionary should +be at least as big as the uncompressed data itself. Future plans +============ - Creating a limited XZ encoder may be considered if people think it is - useful. LZMA2 is slower to compress than e.g. Deflate or LZO even at - the fastest settings, so it isn't clear if LZMA2 encoder is wanted - into the kernel. +Creating a limited XZ encoder may be considered if people think it is +useful. LZMA2 is slower to compress than e.g. Deflate or LZO even at +the fastest settings, so it isn't clear if LZMA2 encoder is wanted +into the kernel. - Support for limited random-access reading is planned for the - decompression code. I don't know if it could have any use in the - kernel, but I know that it would be useful in some embedded projects - outside the Linux kernel. +Support for limited random-access reading is planned for the +decompression code. I don't know if it could have any use in the +kernel, but I know that it would be useful in some embedded projects +outside the Linux kernel. Conformance to the .xz file format specification +================================================ - There are a couple of corner cases where things have been simplified - at expense of detecting errors as early as possible. These should not - matter in practice all, since they don't cause security issues. But - it is good to know this if testing the code e.g. with the test files - from XZ Utils. +There are a couple of corner cases where things have been simplified +at expense of detecting errors as early as possible. These should not +matter in practice all, since they don't cause security issues. But +it is good to know this if testing the code e.g. with the test files +from XZ Utils. Reporting bugs +============== - Before reporting a bug, please check that it's not fixed already - at upstream. See <http://tukaani.org/xz/embedded.html> to get the - latest code. +Before reporting a bug, please check that it's not fixed already +at upstream. See <http://tukaani.org/xz/embedded.html> to get the +latest code. - Report bugs to <lasse.collin@tukaani.org> or visit #tukaani on - Freenode and talk to Larhzu. I don't actively read LKML or other - kernel-related mailing lists, so if there's something I should know, - you should email to me personally or use IRC. +Report bugs to <lasse.collin@tukaani.org> or visit #tukaani on +Freenode and talk to Larhzu. I don't actively read LKML or other +kernel-related mailing lists, so if there's something I should know, +you should email to me personally or use IRC. - Don't bother Igor Pavlov with questions about the XZ implementation - in the kernel or about XZ Utils. While these two implementations - include essential code that is directly based on Igor Pavlov's code, - these implementations aren't maintained nor supported by him. +Don't bother Igor Pavlov with questions about the XZ implementation +in the kernel or about XZ Utils. While these two implementations +include essential code that is directly based on Igor Pavlov's code, +these implementations aren't maintained nor supported by him. diff --git a/Documentation/zorro.txt b/Documentation/zorro.txt index d530971beb00..664072b017e3 100644 --- a/Documentation/zorro.txt +++ b/Documentation/zorro.txt @@ -1,12 +1,13 @@ - Writing Device Drivers for Zorro Devices - ---------------------------------------- +======================================== +Writing Device Drivers for Zorro Devices +======================================== -Written by Geert Uytterhoeven <geert@linux-m68k.org> -Last revised: September 5, 2003 +:Author: Written by Geert Uytterhoeven <geert@linux-m68k.org> +:Last revised: September 5, 2003 -1. Introduction ---------------- +Introduction +------------ The Zorro bus is the bus used in the Amiga family of computers. Thanks to AutoConfig(tm), it's 100% Plug-and-Play. @@ -20,12 +21,12 @@ There are two types of Zorro buses, Zorro II and Zorro III: with Zorro II. The Zorro III address space lies outside the first 16 MB. -2. Probing for Zorro Devices ----------------------------- +Probing for Zorro Devices +------------------------- -Zorro devices are found by calling `zorro_find_device()', which returns a -pointer to the `next' Zorro device with the specified Zorro ID. A probe loop -for the board with Zorro ID `ZORRO_PROD_xxx' looks like: +Zorro devices are found by calling ``zorro_find_device()``, which returns a +pointer to the ``next`` Zorro device with the specified Zorro ID. A probe loop +for the board with Zorro ID ``ZORRO_PROD_xxx`` looks like:: struct zorro_dev *z = NULL; @@ -35,8 +36,8 @@ for the board with Zorro ID `ZORRO_PROD_xxx' looks like: ... } -`ZORRO_WILDCARD' acts as a wildcard and finds any Zorro device. If your driver -supports different types of boards, you can use a construct like: +``ZORRO_WILDCARD`` acts as a wildcard and finds any Zorro device. If your driver +supports different types of boards, you can use a construct like:: struct zorro_dev *z = NULL; @@ -49,24 +50,24 @@ supports different types of boards, you can use a construct like: } -3. Zorro Resources ------------------- +Zorro Resources +--------------- Before you can access a Zorro device's registers, you have to make sure it's not yet in use. This is done using the I/O memory space resource management -functions: +functions:: request_mem_region() release_mem_region() -Shortcuts to claim the whole device's address space are provided as well: +Shortcuts to claim the whole device's address space are provided as well:: zorro_request_device zorro_release_device -4. Accessing the Zorro Address Space ------------------------------------- +Accessing the Zorro Address Space +--------------------------------- The address regions in the Zorro device resources are Zorro bus address regions. Due to the identity bus-physical address mapping on the Zorro bus, @@ -78,26 +79,26 @@ The treatment of these regions depends on the type of Zorro space: explicitly using z_ioremap(). Conversion from bus/physical Zorro II addresses to kernel virtual addresses - and vice versa is done using: + and vice versa is done using:: virt_addr = ZTWO_VADDR(bus_addr); bus_addr = ZTWO_PADDR(virt_addr); - Zorro III address space must be mapped explicitly using z_ioremap() first - before it can be accessed: + before it can be accessed:: virt_addr = z_ioremap(bus_addr, size); ... z_iounmap(virt_addr); -5. References -------------- +References +---------- -linux/include/linux/zorro.h -linux/include/uapi/linux/zorro.h -linux/include/uapi/linux/zorro_ids.h -linux/arch/m68k/include/asm/zorro.h -linux/drivers/zorro -/proc/bus/zorro +#. linux/include/linux/zorro.h +#. linux/include/uapi/linux/zorro.h +#. linux/include/uapi/linux/zorro_ids.h +#. linux/arch/m68k/include/asm/zorro.h +#. linux/drivers/zorro +#. /proc/bus/zorro |