diff options
Diffstat (limited to 'Documentation')
4 files changed, 214 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/max8925.txt b/Documentation/devicetree/bindings/mfd/max8925.txt new file mode 100644 index 000000000000..4f0dc6638e5e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8925.txt @@ -0,0 +1,64 @@ +* Maxim max8925 Power Management IC + +Required parent device properties: +- compatible : "maxim,max8925" +- reg : the I2C slave address for the max8925 chip +- interrupts : IRQ line for the max8925 chip +- interrupt-controller: describes the max8925 as an interrupt + controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the max8925 local IRQ number + +Optional parent device properties: +- maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in + interrupts property, the other is indicated here. + +max8925 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +max8925-onkey : : On key +max8925-rtc : : RTC +max8925-regulator : : Regulators +max8925-backlight : : Backlight +max8925-touch : : Touchscreen +max8925-power : : Charger + +Example: + + pmic: max8925@3c { + compatible = "maxim,max8925"; + reg = <0x3c>; + interrupts = <1>; + interrupt-parent = <&intcmux4>; + interrupt-controller; + #interrupt-cells = <1>; + maxim,tsc-irq = <0>; + + regulators { + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO1 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3900000>; + regulator-boot-on; + regulator-always-on; + }; + + }; + backlight { + maxim,max8925-dual-string = <0>; + }; + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/power_supply/max8925_batter.txt b/Documentation/devicetree/bindings/power_supply/max8925_batter.txt new file mode 100644 index 000000000000..d7e3e0c0f71d --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/max8925_batter.txt @@ -0,0 +1,18 @@ +max8925-battery bindings +~~~~~~~~~~~~~~~~ + +Optional properties : + - batt-detect: whether support battery detect + - topoff-threshold: set charging current in topoff mode + - fast-charge: set charging current in fast mode + - no-temp-support: whether support temperature protection detect + - no-insert-detect: whether support insert detect + +Example: + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt new file mode 100644 index 000000000000..313a60ba61d8 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -0,0 +1,122 @@ +TPS65090 regulators + +Required properties: +- compatible: "ti,tps65090" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + dcdc[1-3], fet[1-7] and ldo[1-2] respectively. +- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively. +- infet[1-7]-supply: The input supply for FET[1-7] respectively. +- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively. + +Optional properties: +- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled then this property should be there. +- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled and if it is from GPIO then GPIO + number should be provided. If it is externally controlled and no GPIO + entry then driver will just configure this rails as external control + and will not provide any enable/disable APIs. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65090@48 { + compatible = "ti,tps65090"; + reg = <0x48>; + interrupts = <0 88 0x4>; + + vsys1-supply = <&some_reg>; + vsys2-supply = <&some_reg>; + vsys3-supply = <&some_reg>; + infet1-supply = <&some_reg>; + infet2-supply = <&some_reg>; + infet3-supply = <&some_reg>; + infet4-supply = <&some_reg>; + infet5-supply = <&some_reg>; + infet6-supply = <&some_reg>; + infet7-supply = <&some_reg>; + vsys_l1-supply = <&some_reg>; + vsys_l2-supply = <&some_reg>; + + regulators { + dcdc1 { + regulator-name = "dcdc1"; + regulator-boot-on; + regulator-always-on; + ti,enable-ext-control; + dcdc-ext-control-gpios = <&gpio 10 0>; + }; + + dcdc2 { + regulator-name = "dcdc2"; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3 { + regulator-name = "dcdc3"; + regulator-boot-on; + regulator-always-on; + }; + + fet1 { + regulator-name = "fet1"; + regulator-boot-on; + regulator-always-on; + }; + + fet2 { + regulator-name = "fet2"; + regulator-boot-on; + regulator-always-on; + }; + + fet3 { + regulator-name = "fet3"; + regulator-boot-on; + regulator-always-on; + }; + + fet4 { + regulator-name = "fet4"; + regulator-boot-on; + regulator-always-on; + }; + + fet5 { + regulator-name = "fet5"; + regulator-boot-on; + regulator-always-on; + }; + + fet6 { + regulator-name = "fet6"; + regulator-boot-on; + regulator-always-on; + }; + + fet7 { + regulator-name = "fet7"; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-boot-on; + regulator-always-on; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt b/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt new file mode 100644 index 000000000000..b4cffdaa4137 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt @@ -0,0 +1,10 @@ +88pm860x-backlight bindings + +Optional properties: + - maxim,max8925-dual-string: whether support dual string + +Example: + + backlights { + maxim,max8925-dual-string = <0>; + }; |