18 files changed, 298 insertions, 21 deletions
diff --git a/Documentation/blackfin/00-INDEX b/Documentation/blackfin/00-INDEX
index 7cb3b356b249..d6840a91e1e1 100644
--- a/Documentation/blackfin/00-INDEX
+++ b/Documentation/blackfin/00-INDEX
@@ -9,3 +9,6 @@ cachefeatures.txt
 
 Filesystems
 	- Requirements for mounting the root file system.
+
+bfin-gpio-note.txt
+	- Notes in developing/using bfin-gpio driver.
diff --git a/Documentation/blackfin/bfin-gpio-notes.txt b/Documentation/blackfin/bfin-gpio-notes.txt
new file mode 100644
index 000000000000..9898c7ded7d3
--- /dev/null
+++ b/Documentation/blackfin/bfin-gpio-notes.txt
@@ -0,0 +1,71 @@
+/*
+ * File:         Documentation/blackfin/bfin-gpio-note.txt
+ * Based on:
+ * Author:
+ *
+ * Created:      $Id: bfin-gpio-note.txt 2008-11-24 16:42 grafyang $
+ * Description:  This file contains the notes in developing/using bfin-gpio.
+ *
+ *
+ * Rev:
+ *
+ * Modified:
+ *               Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ */
+
+
+1. Blackfin GPIO introduction
+
+    There are many GPIO pins on Blackfin. Most of these pins are muxed to
+    multi-functions. They can be configured as peripheral, or just as GPIO,
+    configured to input with interrupt enabled, or output.
+
+    For detailed information, please see "arch/blackfin/kernel/bfin_gpio.c",
+    or the relevant HRM.
+
+
+2. Avoiding resource conflict
+
+    Followed function groups are used to avoiding resource conflict,
+    - Use the pin as peripheral,
+	int peripheral_request(unsigned short per, const char *label);
+	int peripheral_request_list(const unsigned short per[], const char *label);
+	void peripheral_free(unsigned short per);
+	void peripheral_free_list(const unsigned short per[]);
+    - Use the pin as GPIO,
+	int bfin_gpio_request(unsigned gpio, const char *label);
+	void bfin_gpio_free(unsigned gpio);
+    - Use the pin as GPIO interrupt,
+	int bfin_gpio_irq_request(unsigned gpio, const char *label);
+	void bfin_gpio_irq_free(unsigned gpio);
+
+    The request functions will record the function state for a certain pin,
+    the free functions will clear it's function state.
+    Once a pin is requested, it can't be requested again before it is freed by
+    previous caller, otherwise kernel will dump stacks, and the request
+    function fail.
+    These functions are wrapped by other functions, most of the users need not
+    care.
+
+
+3. But there are some exceptions
+    - Kernel permit the identical GPIO be requested both as GPIO and GPIO
+    interrut.
+    Some drivers, like gpio-keys, need this behavior. Kernel only print out
+    warning messages like,
+	bfin-gpio: GPIO 24 is already reserved by gpio-keys: BTN0, and you are
+configuring it as IRQ!
+
+        Note: Consider the case that, if there are two drivers need the
+	identical GPIO, one of them use it as GPIO, the other use it as
+	GPIO interrupt. This will really cause resource conflict. So if
+	there is any abnormal driver behavior, please check the bfin-gpio
+	warning messages.
+
+    - Kernel permit the identical GPIO be requested from the same driver twice.
+
+
+
diff --git a/Documentation/dell_rbu.txt b/Documentation/dell_rbu.txt
index 2c0d631de0cf..c11b931f8f98 100644
--- a/Documentation/dell_rbu.txt
+++ b/Documentation/dell_rbu.txt
@@ -81,8 +81,8 @@ Until this step is completed the driver cannot be unloaded.
 Also echoing either mono ,packet or init in to image_type will free up the
 memory allocated by the driver.
 
-If an user by accident executes steps 1 and 3 above without executing step 2;
-it will make the /sys/class/firmware/dell_rbu/ entries to disappear.
+If a user by accident executes steps 1 and 3 above without executing step 2;
+it will make the /sys/class/firmware/dell_rbu/ entries disappear.
 The entries can be recreated by doing the following
 echo init > /sys/devices/platform/dell_rbu/image_type
 NOTE: echoing init in image_type does not change it original value.
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index 2193be53e773..5ddbe350487a 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -318,6 +318,14 @@ Who:	Jean Delvare <khali@linux-fr.org>
 
 ---------------------------
 
+What:	fscher and fscpos drivers
+When:	June 2009
+Why:	Deprecated by the new fschmd driver.
+Who:	Hans de Goede <hdegoede@redhat.com>
+	Jean Delvare <khali@linux-fr.org>
+
+---------------------------
+
 What:	SELinux "compat_net" functionality
 When:	2.6.30 at the earliest
 Why:	In 2.6.18 the Secmark concept was introduced to replace the "compat_net"
diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt
index 32e94635484f..d105eb45282a 100644
--- a/Documentation/filesystems/proc.txt
+++ b/Documentation/filesystems/proc.txt
@@ -140,6 +140,7 @@ Table 1-1: Process specific entries in /proc
  statm		Process memory status information
  status		Process status in human readable form
  wchan		If CONFIG_KALLSYMS is set, a pre-decoded wchan
+ stack		Report full stack trace, enable via CONFIG_STACKTRACE
  smaps		Extension based on maps, the rss size for each mapped file
 ..............................................................................
 
diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet
index aef5a9b36846..4d184f2db0ea 100644
--- a/Documentation/hwmon/abituguru-datasheet
+++ b/Documentation/hwmon/abituguru-datasheet
@@ -74,7 +74,7 @@ a sensor.
 Notice that some banks have both a read and a write address this is how the
 uGuru determines if a read from or a write to the bank is taking place, thus
 when reading you should always use the read address and when writing the
-write address. The write address is always one (1) more then the read address.
+write address. The write address is always one (1) more than the read address.
 
 
 uGuru ready
@@ -224,7 +224,7 @@ Bit 3: Beep if alarm							(RW)
 Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
 Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
 Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
-Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds	(RW)
        Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
 
 *  This bit is only honored/used by the uGuru if a temp sensor is connected
@@ -293,7 +293,7 @@ Byte 0:
 Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
 Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
 Bit 3: Beep if alarm						(RW)
-Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Shutdown if alarm persist for more than 4 seconds	(RW)
 
 Byte 1:
 min threshold (scale as bank 0x26)
diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
new file mode 100644
index 000000000000..a8321267b5b6
--- /dev/null
+++ b/Documentation/hwmon/f71882fg
@@ -0,0 +1,89 @@
+Kernel driver f71882fg
+======================
+
+Supported chips:
+  * Fintek F71882FG and F71883FG
+    Prefix: 'f71882fg'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Available from the Fintek website
+  * Fintek F71862FG and F71863FG
+    Prefix: 'f71862fg'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Available from the Fintek website
+  * Fintek F8000
+    Prefix: 'f8000'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Not public
+
+Author: Hans de Goede <hdegoede@redhat.com>
+
+
+Description
+-----------
+
+Fintek F718xxFG/F8000 Super I/O chips include complete hardware monitoring
+capabilities. They can monitor up to 9 voltages (3 for the F8000), 4 fans and
+3 temperature sensors.
+
+These chips also have fan controlling features, using either DC or PWM, in
+three different modes (one manual, two automatic).
+
+The driver assumes that no more than one chip is present, which seems
+reasonable.
+
+
+Monitoring
+----------
+
+The Voltage, Fan and Temperature Monitoring uses the standard sysfs
+interface as documented in sysfs-interface, without any exceptions.
+
+
+Fan Control
+-----------
+
+Both PWM (pulse-width modulation) and DC fan speed control methods are
+supported. The right one to use depends on external circuitry on the
+motherboard, so the driver assumes that the BIOS set the method
+properly.
+
+There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
+voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
+mode where the actual RPM of the fan (as measured) is controlled and the speed
+gets specified as 0-100% of the fan#_full_speed file.
+
+Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a
+whole lot of a difference when modifying fan control settings. The only
+important difference is that in RPM mode the 0-100% controls the fan speed
+between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs
+RPM mode, it will also set fan#_full_speed properly, if it does not then
+fan control will not work properly, unless you set a sane fan#_full_speed
+value yourself.
+
+Switching between these modes requires re-initializing a whole bunch of
+registers, so the mode which the BIOS has set is kept. The mode is
+printed when loading the driver.
+
+Three different fan control modes are supported; the mode number is written
+to the pwm#_enable file. Note that not all modes are supported on all
+chips, and some modes may only be available in RPM / PWM mode on the F8000.
+Writing an unsupported mode will result in an invalid parameter error.
+
+* 1: Manual mode
+  You ask for a specific PWM duty cycle / DC voltage or a specific % of
+  fan#_full_speed by writing to the pwm# file. This mode is only
+  available on the F8000 if the fan channel is in RPM mode.
+
+* 2: Normal auto mode
+  You can define a number of temperature/fan speed trip points, which % the
+  fan should run at at this temp and which temp a fan should follow using the
+  standard sysfs interface. The number and type of trip points is chip
+  depended, see which files are available in sysfs.
+  Fan/PWM channel 3 of the F8000 is always in this mode!
+
+* 3: Thermostat mode (Only available on the F8000 when in duty cycle mode)
+  The fan speed is regulated to keep the temp the fan is mapped to between
+  temp#_auto_point2_temp and temp#_auto_point3_temp.
+
+Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
+fan2 and pwm3 to fan3.
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index 042c0415140b..659315d98e00 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -26,6 +26,10 @@ Supported chips:
     Datasheet: Publicly available at the ITE website
                http://www.ite.com.tw/product_info/file/pc/IT8718F_V0.2.zip
                http://www.ite.com.tw/product_info/file/pc/IT8718F_V0%203_(for%20C%20version).zip
+  * IT8720F
+    Prefix: 'it8720'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not yet publicly available.
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -71,7 +75,7 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8726F and SiS950 chips.
+IT8718F, IT8720F, IT8726F and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -84,19 +88,19 @@ the IT8716F and late IT8712F have 6. They are shared with other functions
 though, so the functionality may not be available on a given system.
 The driver dumbly assume it is there.
 
-The IT8718F also features VID inputs (up to 8 pins) but the value is
-stored in the Super-I/O configuration space. Due to technical limitations,
+The IT8718F and IT8720F also features VID inputs (up to 8 pins) but the value
+is stored in the Super-I/O configuration space. Due to technical limitations,
 this value can currently only be read once at initialization time, so
 the driver won't notice and report changes in the VID value. The two
 upper VID bits share their pins with voltage inputs (in5 and in6) so you
 can't have both on a given board.
 
-The IT8716F, IT8718F and later IT8712F revisions have support for
+The IT8716F, IT8718F, IT8720F and later IT8712F revisions have support for
 2 additional fans. The additional fans are supported by the driver.
 
-The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
-16-bit tachometer counters for fans 1 to 3. This is better (no more fan
-clock divider mess) but not compatible with the older chips and
+The IT8716F, IT8718F and IT8720F, and late IT8712F and IT8705F also have
+optional 16-bit tachometer counters for fans 1 to 3. This is better (no more
+fan clock divider mess) but not compatible with the older chips and
 revisions. The 16-bit tachometer mode is enabled by the driver when one
 of the above chips is detected.
 
@@ -122,7 +126,7 @@ zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
 0.016 volt. The battery voltage in8 does not have limit registers.
 
-The VID lines (IT8712F/IT8716F/IT8718F) encode the core voltage value:
+The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
 the voltage level your processor should work with. This is hardcoded by
 the mainboard and/or processor itself. It is a value in volts.
 
diff --git a/Documentation/hwmon/lm70 b/Documentation/hwmon/lm70
index 2bdd3feebf53..0d240291e3cc 100644
--- a/Documentation/hwmon/lm70
+++ b/Documentation/hwmon/lm70
@@ -1,9 +1,11 @@
 Kernel driver lm70
 ==================
 
-Supported chip:
+Supported chips:
   * National Semiconductor LM70
     Datasheet: http://www.national.com/pf/LM/LM70.html
+  * Texas Instruments TMP121/TMP123
+    Information: http://focus.ti.com/docs/prod/folders/print/tmp121.html
 
 Author:
         Kaiwan N Billimoria <kaiwan@designergraphix.com>
@@ -25,6 +27,14 @@ complement digital temperature (sent via the SIO line), is available in the
 driver for interpretation. This driver makes use of the kernel's in-core
 SPI support.
 
+As a real (in-tree) example of this "SPI protocol driver" interfacing
+with a "SPI master controller driver", see drivers/spi/spi_lm70llp.c
+and its associated documentation.
+
+The TMP121/TMP123 are very similar; main differences are 4 wire SPI inter-
+face (read only) and 13-bit temperature data (0.0625 degrees celsius reso-
+lution).
+
 Thanks to
 ---------
 Jean Delvare <khali@linux-fr.org> for mentoring the hwmon-side driver
diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 400620741290..a13680871bc7 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -164,7 +164,7 @@ configured individually according to the following options.
                       temperature. (PWM value from 0 to 255)
 
 * pwm#_auto_pwm_minctl - this flags selects for temp#_auto_temp_off temperature
-                         the bahaviour of fans. Write 1 to let fans spinning at
+                         the behaviour of fans. Write 1 to let fans spinning at
 			 pwm#_auto_pwm_min or write 0 to let them off.
 
 NOTE: It has been reported that there is a bug in the LM85 that causes the flag
diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245
new file mode 100644
index 000000000000..bae7a3adc5d8
--- /dev/null
+++ b/Documentation/hwmon/ltc4245
@@ -0,0 +1,81 @@
+Kernel driver ltc4245
+=====================
+
+Supported chips:
+  * Linear Technology LTC4245
+    Prefix: 'ltc4245'
+    Addresses scanned: 0x20-0x3f
+    Datasheet:
+        http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517
+
+Author: Ira W. Snyder <iws@ovro.caltech.edu>
+
+
+Description
+-----------
+
+The LTC4245 controller allows a board to be safely inserted and removed
+from a live backplane in multiple supply systems such as CompactPCI and
+PCI Express.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4245 devices, due to the fact that some
+of the possible addresses are unfriendly to probing. You will need to use
+the "force" parameter to tell the driver where to find the device.
+
+Example: the following will load the driver for an LTC4245 at address 0x23
+on I2C bus #1:
+$ modprobe ltc4245 force=1,0x23
+
+
+Sysfs entries
+-------------
+
+The LTC4245 has built-in limits for over and under current warnings. This
+makes it very likely that the reference circuit will be used.
+
+This driver uses the values in the datasheet to change the register values
+into the values specified in the sysfs-interface document. The current readings
+rely on the sense resistors listed in Table 2: "Sense Resistor Values".
+
+in1_input		12v input voltage (mV)
+in2_input		5v  input voltage (mV)
+in3_input		3v  input voltage (mV)
+in4_input		Vee (-12v) input voltage (mV)
+
+in1_min_alarm		12v input undervoltage alarm
+in2_min_alarm		5v  input undervoltage alarm
+in3_min_alarm		3v  input undervoltage alarm
+in4_min_alarm		Vee (-12v) input undervoltage alarm
+
+curr1_input		12v current (mA)
+curr2_input		5v  current (mA)
+curr3_input		3v  current (mA)
+curr4_input		Vee (-12v) current (mA)
+
+curr1_max_alarm		12v overcurrent alarm
+curr2_max_alarm		5v  overcurrent alarm
+curr3_max_alarm		3v  overcurrent alarm
+curr4_max_alarm		Vee (-12v) overcurrent alarm
+
+in5_input		12v output voltage (mV)
+in6_input		5v  output voltage (mV)
+in7_input		3v  output voltage (mV)
+in8_input		Vee (-12v) output voltage (mV)
+
+in5_min_alarm		12v output undervoltage alarm
+in6_min_alarm		5v  output undervoltage alarm
+in7_min_alarm		3v  output undervoltage alarm
+in8_min_alarm		Vee (-12v) output undervoltage alarm
+
+in9_input		GPIO #1 voltage data
+in10_input		GPIO #2 voltage data
+in11_input		GPIO #3 voltage data
+
+power1_input		12v power usage (mW)
+power2_input		5v  power usage (mW)
+power3_input		3v  power usage (mW)
+power4_input		Vee (-12v) power usage (mW)
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt
index 71f0fe1fc1b0..898b4987bb80 100644
--- a/Documentation/laptops/thinkpad-acpi.txt
+++ b/Documentation/laptops/thinkpad-acpi.txt
@@ -1475,7 +1475,7 @@ Sysfs interface changelog:
 
 0x020100:	Marker for thinkpad-acpi with hot key NVRAM polling
 		support.  If you must, use it to know you should not
-		start an userspace NVRAM poller (allows to detect when
+		start a userspace NVRAM poller (allows to detect when
 		NVRAM is compiled out by the user because it is
 		unneeded/undesired in the first place).
 0x020101:	Marker for thinkpad-acpi with hot key NVRAM polling
diff --git a/Documentation/networking/rxrpc.txt b/Documentation/networking/rxrpc.txt
index c3669a3fb4af..60d05eb77c64 100644
--- a/Documentation/networking/rxrpc.txt
+++ b/Documentation/networking/rxrpc.txt
@@ -540,7 +540,7 @@ A client would issue an operation by:
      MSG_MORE should be set in msghdr::msg_flags on all but the last part of
      the request.  Multiple requests may be made simultaneously.
 
-     If a call is intended to go to a destination other then the default
+     If a call is intended to go to a destination other than the default
      specified through connect(), then msghdr::msg_name should be set on the
      first request message of that call.
 
diff --git a/Documentation/networking/tuntap.txt b/Documentation/networking/tuntap.txt
index 839cbb71388b..c0aab985bad9 100644
--- a/Documentation/networking/tuntap.txt
+++ b/Documentation/networking/tuntap.txt
@@ -118,7 +118,7 @@ As mentioned above, main purpose of TUN/TAP driver is tunneling.
 It is used by VTun (http://vtun.sourceforge.net).
 
 Another interesting application using TUN/TAP is pipsecd
-(http://perso.enst.fr/~beyssac/pipsec/), an userspace IPSec
+(http://perso.enst.fr/~beyssac/pipsec/), a userspace IPSec
 implementation that can use complete kernel routing (unlike FreeS/WAN).
 
 3. How does Virtual network device actually work ? 
diff --git a/Documentation/scsi/ChangeLog.lpfc b/Documentation/scsi/ChangeLog.lpfc
index ae3f962a7cfc..ff19a52fe004 100644
--- a/Documentation/scsi/ChangeLog.lpfc
+++ b/Documentation/scsi/ChangeLog.lpfc
@@ -733,7 +733,7 @@ Changes from 20040920 to 20041018
 	  I/O completion path a little more, especially taking care of
 	  fast-pathing the non-error case.  Also removes tons of dead
 	  members and defines from lpfc_scsi.h - e.g. lpfc_target is down
-	  to nothing more then the lpfc_nodelist pointer.
+	  to nothing more than the lpfc_nodelist pointer.
 	* Added binary sysfs file to issue mbox commands
 	* Replaced #if __BIG_ENDIAN with #if __BIG_ENDIAN_BITFIELD for
 	  compatibility with the user space applications.
diff --git a/Documentation/scsi/ChangeLog.ncr53c8xx b/Documentation/scsi/ChangeLog.ncr53c8xx
index a9f721aeb11c..8b278c10edfd 100644
--- a/Documentation/scsi/ChangeLog.ncr53c8xx
+++ b/Documentation/scsi/ChangeLog.ncr53c8xx
@@ -19,7 +19,7 @@ Sun Sep 24 21:30 2000 Gerard Roudier (groudier@club-internet.fr)
 
 Wed Jul 26 23:30 2000 Gerard Roudier (groudier@club-internet.fr)
 	* version ncr53c8xx-3.4.1
-	- Provide OpenFirmare path through the proc FS on PPC.
+	- Provide OpenFirmware path through the proc FS on PPC.
 	- Remove trailing argument #2 from a couple of #undefs.
 
 Sun Jul 09 16:30 2000 Gerard Roudier (groudier@club-internet.fr)
diff --git a/Documentation/scsi/ChangeLog.sym53c8xx b/Documentation/scsi/ChangeLog.sym53c8xx
index ef985ec348e6..02ffbc1e8a84 100644
--- a/Documentation/scsi/ChangeLog.sym53c8xx
+++ b/Documentation/scsi/ChangeLog.sym53c8xx
@@ -81,7 +81,7 @@ Sun Sep 24 21:30 2000 Gerard Roudier (groudier@club-internet.fr)
 
 Wed Jul 26 23:30 2000 Gerard Roudier (groudier@club-internet.fr)
 	* version sym53c8xx-1.7.1
-	- Provide OpenFirmare path through the proc FS on PPC.
+	- Provide OpenFirmware path through the proc FS on PPC.
 	- Download of on-chip SRAM using memcpy_toio() doesn't work 
 	  on PPC. Restore previous method (MEMORY MOVE from SCRIPTS).
 	- Remove trailing argument #2 from a couple of #undefs.
diff --git a/Documentation/spi/spi-lm70llp b/Documentation/spi/spi-lm70llp
index 154bd02220b9..34a9cfd746bd 100644
--- a/Documentation/spi/spi-lm70llp
+++ b/Documentation/spi/spi-lm70llp
@@ -13,10 +13,20 @@ Description
 This driver provides glue code connecting a National Semiconductor LM70 LLP
 temperature sensor evaluation board to the kernel's SPI core subsystem.
 
+This is a SPI master controller driver. It can be used in conjunction with
+(layered under) the LM70 logical driver (a "SPI protocol driver").
 In effect, this driver turns the parallel port interface on the eval board
 into a SPI bus with a single device, which will be driven by the generic
 LM70 driver (drivers/hwmon/lm70.c).
 
+
+Hardware Interfacing
+--------------------
+The schematic for this particular board (the LM70EVAL-LLP) is
+available (on page 4) here:
+
+  http://www.national.com/appinfo/tempsensors/files/LM70LLPEVALmanual.pdf
+
 The hardware interfacing on the LM70 LLP eval board is as follows:
 
    Parallel                 LM70 LLP