diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 89 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/mtd-physmap.txt | 80 |
2 files changed, 92 insertions, 77 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 0ab0230cbcb0..d16b7a1c3793 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -43,12 +43,11 @@ Table of Contents 2) Representing devices without a current OF specification a) PHY nodes b) Interrupt controllers - c) CFI or JEDEC memory-mapped NOR flash - d) 4xx/Axon EMAC ethernet nodes - e) Xilinx IP cores - f) USB EHCI controllers - g) MDIO on GPIOs - h) SPI busses + c) 4xx/Axon EMAC ethernet nodes + d) Xilinx IP cores + e) USB EHCI controllers + f) MDIO on GPIOs + g) SPI busses VII - Marvell Discovery mv64[345]6x System Controller chips 1) The /system-controller node @@ -999,7 +998,7 @@ compatibility. translation of SOC addresses for memory mapped SOC registers. - bus-frequency: Contains the bus frequency for the SOC node. Typically, the value of this field is filled in by the boot - loader. + loader. Recommended properties: @@ -1287,71 +1286,7 @@ platforms are moved over to use the flattened-device-tree model. device_type = "open-pic"; }; - c) CFI or JEDEC memory-mapped NOR flash - - Flash chips (Memory Technology Devices) are often used for solid state - file systems on embedded devices. - - - compatible : should contain the specific model of flash chip(s) - used, if known, followed by either "cfi-flash" or "jedec-flash" - - reg : Address range of the flash chip - - bank-width : Width (in bytes) of the flash bank. Equal to the - device width times the number of interleaved chips. - - device-width : (optional) Width of a single flash chip. If - omitted, assumed to be equal to 'bank-width'. - - #address-cells, #size-cells : Must be present if the flash has - sub-nodes representing partitions (see below). In this case - both #address-cells and #size-cells must be equal to 1. - - For JEDEC compatible devices, the following additional properties - are defined: - - - vendor-id : Contains the flash chip's vendor id (1 byte). - - device-id : Contains the flash chip's device id (1 byte). - - In addition to the information on the flash bank itself, the - device tree may optionally contain additional information - describing partitions of the flash address space. This can be - used on platforms which have strong conventions about which - portions of the flash are used for what purposes, but which don't - use an on-flash partition table such as RedBoot. - - Each partition is represented as a sub-node of the flash device. - Each node's name represents the name of the corresponding - partition of the flash device. - - Flash partitions - - reg : The partition's offset and size within the flash bank. - - label : (optional) The label / name for this flash partition. - If omitted, the label is taken from the node name (excluding - the unit address). - - read-only : (optional) This parameter, if present, is a hint to - Linux that this flash partition should only be mounted - read-only. This is usually used for flash partitions - containing early-boot firmware images or data which should not - be clobbered. - - Example: - - flash@ff000000 { - compatible = "amd,am29lv128ml", "cfi-flash"; - reg = <ff000000 01000000>; - bank-width = <4>; - device-width = <1>; - #address-cells = <1>; - #size-cells = <1>; - fs@0 { - label = "fs"; - reg = <0 f80000>; - }; - firmware@f80000 { - label ="firmware"; - reg = <f80000 80000>; - read-only; - }; - }; - - d) 4xx/Axon EMAC ethernet nodes + c) 4xx/Axon EMAC ethernet nodes The EMAC ethernet controller in IBM and AMCC 4xx chips, and also the Axon bridge. To operate this needs to interact with a ths @@ -1499,7 +1434,7 @@ platforms are moved over to use the flattened-device-tree model. available. For Axon: 0x0000012a - e) Xilinx IP cores + d) Xilinx IP cores The Xilinx EDK toolchain ships with a set of IP cores (devices) for use in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range @@ -1761,7 +1696,7 @@ platforms are moved over to use the flattened-device-tree model. listed above, nodes for these devices should include a phy-handle property, and may include other common network device properties like local-mac-address. - + iv) Xilinx Uartlite Xilinx uartlite devices are simple fixed speed serial ports. @@ -1793,7 +1728,7 @@ platforms are moved over to use the flattened-device-tree model. - reg-offset : A value of 3 is required - reg-shift : A value of 2 is required - f) USB EHCI controllers + e) USB EHCI controllers Required properties: - compatible : should be "usb-ehci". @@ -1819,7 +1754,7 @@ platforms are moved over to use the flattened-device-tree model. big-endian; }; - g) MDIO on GPIOs + f) MDIO on GPIOs Currently defined compatibles: - virtual,gpio-mdio @@ -1839,7 +1774,7 @@ platforms are moved over to use the flattened-device-tree model. &qe_pio_c 6>; }; - h) SPI (Serial Peripheral Interface) busses + g) SPI (Serial Peripheral Interface) busses SPI busses can be described with a node for the SPI master device and a set of child nodes for each SPI slave on the bus. For this diff --git a/Documentation/powerpc/dts-bindings/mtd-physmap.txt b/Documentation/powerpc/dts-bindings/mtd-physmap.txt new file mode 100644 index 000000000000..667c9bde8699 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/mtd-physmap.txt @@ -0,0 +1,80 @@ +CFI or JEDEC memory-mapped NOR flash + +Flash chips (Memory Technology Devices) are often used for solid state +file systems on embedded devices. + + - compatible : should contain the specific model of flash chip(s) + used, if known, followed by either "cfi-flash" or "jedec-flash" + - reg : Address range(s) of the flash chip(s) + It's possible to (optionally) define multiple "reg" tuples so that + non-identical NOR chips can be described in one flash node. + - bank-width : Width (in bytes) of the flash bank. Equal to the + device width times the number of interleaved chips. + - device-width : (optional) Width of a single flash chip. If + omitted, assumed to be equal to 'bank-width'. + - #address-cells, #size-cells : Must be present if the flash has + sub-nodes representing partitions (see below). In this case + both #address-cells and #size-cells must be equal to 1. + +For JEDEC compatible devices, the following additional properties +are defined: + + - vendor-id : Contains the flash chip's vendor id (1 byte). + - device-id : Contains the flash chip's device id (1 byte). + +In addition to the information on the flash bank itself, the +device tree may optionally contain additional information +describing partitions of the flash address space. This can be +used on platforms which have strong conventions about which +portions of the flash are used for what purposes, but which don't +use an on-flash partition table such as RedBoot. + +Each partition is represented as a sub-node of the flash device. +Each node's name represents the name of the corresponding +partition of the flash device. + +Flash partitions + - reg : The partition's offset and size within the flash bank. + - label : (optional) The label / name for this flash partition. + If omitted, the label is taken from the node name (excluding + the unit address). + - read-only : (optional) This parameter, if present, is a hint to + Linux that this flash partition should only be mounted + read-only. This is usually used for flash partitions + containing early-boot firmware images or data which should not + be clobbered. + +Example: + + flash@ff000000 { + compatible = "amd,am29lv128ml", "cfi-flash"; + reg = <ff000000 01000000>; + bank-width = <4>; + device-width = <1>; + #address-cells = <1>; + #size-cells = <1>; + fs@0 { + label = "fs"; + reg = <0 f80000>; + }; + firmware@f80000 { + label ="firmware"; + reg = <f80000 80000>; + read-only; + }; + }; + +Here an example with multiple "reg" tuples: + + flash@f0000000,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "intel,PC48F4400P0VB", "cfi-flash"; + reg = <0 0x00000000 0x02000000 + 0 0x02000000 0x02000000>; + bank-width = <2>; + partition@0 { + label = "test-part1"; + reg = <0 0x04000000>; + }; + }; |