diff options
Diffstat (limited to 'Documentation')
9 files changed, 330 insertions, 32 deletions
diff --git a/Documentation/PCI/pci-error-recovery.rst b/Documentation/PCI/pci-error-recovery.rst index 9fa49a6ece85..84ceebb08cac 100644 --- a/Documentation/PCI/pci-error-recovery.rst +++ b/Documentation/PCI/pci-error-recovery.rst @@ -79,7 +79,7 @@ This structure has the form:: struct pci_error_handlers { - int (*error_detected)(struct pci_dev *dev, enum pci_channel_state); + int (*error_detected)(struct pci_dev *dev, pci_channel_state_t); int (*mmio_enabled)(struct pci_dev *dev); int (*slot_reset)(struct pci_dev *dev); void (*resume)(struct pci_dev *dev); @@ -87,11 +87,11 @@ This structure has the form:: The possible channel states are:: - enum pci_channel_state { + typedef enum { pci_channel_io_normal, /* I/O channel is in normal state */ pci_channel_io_frozen, /* I/O to channel is blocked */ pci_channel_io_perm_failure, /* PCI card is dead */ - }; + } pci_channel_state_t; Possible return values are:: @@ -348,7 +348,7 @@ STEP 6: Permanent Failure ------------------------- A "permanent failure" has occurred, and the platform cannot recover the device. The platform will call error_detected() with a -pci_channel_state value of pci_channel_io_perm_failure. +pci_channel_state_t value of pci_channel_io_perm_failure. The device driver should, at this point, assume the worst. It should cancel all pending I/O, refuse all new I/O, returning -EIO to diff --git a/Documentation/PCI/pci.rst b/Documentation/PCI/pci.rst index c35b187d5479..814b40f8360b 100644 --- a/Documentation/PCI/pci.rst +++ b/Documentation/PCI/pci.rst @@ -17,7 +17,7 @@ PCI device drivers. A more complete resource is the third edition of "Linux Device Drivers" by Jonathan Corbet, Alessandro Rubini, and Greg Kroah-Hartman. LDD3 is available for free (under Creative Commons License) from: -http://lwn.net/Kernel/LDD3/. +https://lwn.net/Kernel/LDD3/. However, keep in mind that all documents are subject to "bit rot". Refer to the source code if things are not working as described here. @@ -214,7 +214,7 @@ the PCI device by calling pci_enable_device(). This will: problem and unlikely to get fixed soon. This has been discussed before but not changed as of 2.6.19: - http://lkml.org/lkml/2006/3/2/194 + https://lore.kernel.org/r/20060302180025.GC28895@flint.arm.linux.org.uk/ pci_set_master() will enable DMA by setting the bus master bit @@ -514,9 +514,8 @@ your driver if they're helpful, or just use plain hex constants. The device IDs are arbitrary hex numbers (vendor controlled) and normally used only in a single location, the pci_device_id table. -Please DO submit new vendor/device IDs to http://pci-ids.ucw.cz/. -There are mirrors of the pci.ids file at http://pciids.sourceforge.net/ -and https://github.com/pciutils/pciids. +Please DO submit new vendor/device IDs to https://pci-ids.ucw.cz/. +There's a mirror of the pci.ids file at https://github.com/pciutils/pciids. Obsolete functions diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml index 84a8f095d031..6d67067843bf 100644 --- a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml +++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml @@ -18,13 +18,12 @@ properties: const: cdns,cdns-pcie-host reg: - maxItems: 3 + maxItems: 2 reg-names: items: - const: reg - const: cfg - - const: mem msi-parent: true @@ -49,9 +48,8 @@ examples: device-id = <0x0200>; reg = <0x0 0xfb000000 0x0 0x01000000>, - <0x0 0x41000000 0x0 0x00001000>, - <0x0 0x40000000 0x0 0x04000000>; - reg-names = "reg", "cfg", "mem"; + <0x0 0x41000000 0x0 0x00001000>; + reg-names = "reg", "cfg"; ranges = <0x02000000 0x0 0x42000000 0x0 0x42000000 0x0 0x1000000>, <0x01000000 0x0 0x43000000 0x0 0x43000000 0x0 0x0010000>; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 7939bca47861..d099f3476ccc 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -112,28 +112,16 @@ Power supplies for Tegra124: - Required: - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. - - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must - supply 1.05 V. - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. Must supply 3.3 V. - - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). - Must supply 3.3 V. - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must supply 2.8-3.3 V. - - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must - supply 1.05 V. Power supplies for Tegra210: - Required: - - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must - supply 1.05 V. - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. Must supply 1.8 V. - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. - - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must - supply 1.05 V. - - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). - Must supply 3.3 V. - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must supply 1.8 V. diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 29bcbd88f457..6a8f2874a24d 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -1,12 +1,12 @@ PCI bus bridges have standardized Device Tree bindings: PCI Bus Binding to: IEEE Std 1275-1994 -http://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf +https://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf And for the interrupt mapping part: Open Firmware Recommended Practice: Interrupt Mapping -http://www.devicetree.org/open-firmware/practice/imap/imap0_9d.pdf +https://www.devicetree.org/open-firmware/practice/imap/imap0_9d.pdf Additionally to the properties specified in the above standards a host bridge driver implementation may support the following properties: diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 981b4de12807..02bc81bb8b2d 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -5,6 +5,7 @@ Value type: <stringlist> Definition: Value should contain - "qcom,pcie-ipq8064" for ipq8064 + - "qcom,pcie-ipq8064-v2" for ipq8064 rev 2 or ipq8065 - "qcom,pcie-apq8064" for apq8064 - "qcom,pcie-apq8084" for apq8084 - "qcom,pcie-msm8996" for msm8996 or apq8096 @@ -90,6 +91,8 @@ Definition: Should contain the following entries - "core" Clocks the pcie hw block - "phy" Clocks the pcie PHY block + - "aux" Clocks the pcie AUX block + - "ref" Clocks the pcie ref block - clock-names: Usage: required for apq8084/ipq4019 Value type: <stringlist> @@ -177,6 +180,7 @@ - "pwr" PWR reset - "ahb" AHB reset - "phy_ahb" PHY AHB reset + - "ext" EXT reset - reset-names: Usage: required for ipq8074 @@ -277,14 +281,17 @@ <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ clocks = <&gcc PCIE_A_CLK>, <&gcc PCIE_H_CLK>, - <&gcc PCIE_PHY_CLK>; - clock-names = "core", "iface", "phy"; + <&gcc PCIE_PHY_CLK>, + <&gcc PCIE_AUX_CLK>, + <&gcc PCIE_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; resets = <&gcc PCIE_ACLK_RESET>, <&gcc PCIE_HCLK_RESET>, <&gcc PCIE_POR_RESET>, <&gcc PCIE_PCI_RESET>, - <&gcc PCIE_PHY_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy"; + <&gcc PCIE_PHY_RESET>, + <&gcc PCIE_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; pinctrl-0 = <&pcie_pins_default>; pinctrl-names = "default"; }; diff --git a/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml b/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml new file mode 100644 index 000000000000..cfe25cface21 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/ +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/pci/ti,j721e-pci-ep.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI J721E PCI EP (PCIe Wrapper) + +maintainers: + - Kishon Vijay Abraham I <kishon@ti.com> + +allOf: + - $ref: "cdns-pcie-ep.yaml#" + +properties: + compatible: + enum: + - ti,j721e-pcie-ep + + reg: + maxItems: 4 + + reg-names: + items: + - const: intd_cfg + - const: user_cfg + - const: reg + - const: mem + + ti,syscon-pcie-ctrl: + description: Phandle to the SYSCON entry required for configuring PCIe mode + and link speed. + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + + power-domains: + maxItems: 1 + + clocks: + maxItems: 1 + description: clock-specifier to represent input to the PCIe + + clock-names: + items: + - const: fck + + dma-coherent: + description: Indicates that the PCIe IP block can ensure the coherency + +required: + - compatible + - reg + - reg-names + - ti,syscon-pcie-ctrl + - max-link-speed + - num-lanes + - power-domains + - clocks + - clock-names + - cdns,max-outbound-regions + - dma-coherent + - max-functions + - phys + - phy-names + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + pcie0_ep: pcie-ep@d000000 { + compatible = "ti,j721e-pcie-ep"; + reg = <0x00 0x02900000 0x00 0x1000>, + <0x00 0x02907000 0x00 0x400>, + <0x00 0x0d000000 0x00 0x00800000>, + <0x00 0x10000000 0x00 0x08000000>; + reg-names = "intd_cfg", "user_cfg", "reg", "mem"; + ti,syscon-pcie-ctrl = <&pcie0_ctrl>; + max-link-speed = <3>; + num-lanes = <2>; + power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 239 1>; + clock-names = "fck"; + cdns,max-outbound-regions = <16>; + max-functions = /bits/ 8 <6>; + dma-coherent; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml b/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml new file mode 100644 index 000000000000..d7b60487c6c3 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/pci/ti,j721e-pci-host.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI J721E PCI Host (PCIe Wrapper) + +maintainers: + - Kishon Vijay Abraham I <kishon@ti.com> + +allOf: + - $ref: "cdns-pcie-host.yaml#" + +properties: + compatible: + enum: + - ti,j721e-pcie-host + + reg: + maxItems: 4 + + reg-names: + items: + - const: intd_cfg + - const: user_cfg + - const: reg + - const: cfg + + ti,syscon-pcie-ctrl: + description: Phandle to the SYSCON entry required for configuring PCIe mode + and link speed. + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + + power-domains: + maxItems: 1 + + clocks: + maxItems: 1 + description: clock-specifier to represent input to the PCIe + + clock-names: + items: + - const: fck + + vendor-id: + const: 0x104c + + device-id: + const: 0xb00d + + msi-map: true + +required: + - compatible + - reg + - reg-names + - ti,syscon-pcie-ctrl + - max-link-speed + - num-lanes + - power-domains + - clocks + - clock-names + - vendor-id + - device-id + - msi-map + - dma-coherent + - dma-ranges + - ranges + - reset-gpios + - phys + - phy-names + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + #include <dt-bindings/gpio/gpio.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + pcie0_rc: pcie@2900000 { + compatible = "ti,j721e-pcie-host"; + reg = <0x00 0x02900000 0x00 0x1000>, + <0x00 0x02907000 0x00 0x400>, + <0x00 0x0d000000 0x00 0x00800000>, + <0x00 0x10000000 0x00 0x00001000>; + reg-names = "intd_cfg", "user_cfg", "reg", "cfg"; + ti,syscon-pcie-ctrl = <&pcie0_ctrl>; + max-link-speed = <3>; + num-lanes = <2>; + power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 239 1>; + clock-names = "fck"; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xf>; + vendor-id = <0x104c>; + device-id = <0xb00d>; + msi-map = <0x0 &gic_its 0x0 0x10000>; + dma-coherent; + reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + ranges = <0x01000000 0x0 0x10001000 0x00 0x10001000 0x0 0x0010000>, + <0x02000000 0x0 0x10011000 0x00 0x10011000 0x0 0x7fef000>; + dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-versal-cpm.yaml b/Documentation/devicetree/bindings/pci/xilinx-versal-cpm.yaml new file mode 100644 index 000000000000..a2bbc0eb7220 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-versal-cpm.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/xilinx-versal-cpm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: CPM Host Controller device tree for Xilinx Versal SoCs + +maintainers: + - Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> + +allOf: + - $ref: /schemas/pci/pci-bus.yaml# + +properties: + compatible: + const: xlnx,versal-cpm-host-1.00 + + reg: + items: + - description: Configuration space region and bridge registers. + - description: CPM system level control and status registers. + + reg-names: + items: + - const: cfg + - const: cpm_slcr + + interrupts: + maxItems: 1 + + msi-map: + description: + Maps a Requester ID to an MSI controller and associated MSI sideband data. + + ranges: + maxItems: 2 + + "#interrupt-cells": + const: 1 + + interrupt-controller: + description: Interrupt controller node for handling legacy PCI interrupts. + type: object + properties: + "#address-cells": + const: 0 + "#interrupt-cells": + const: 1 + "interrupt-controller": true + additionalProperties: false + +required: + - reg + - reg-names + - "#interrupt-cells" + - interrupts + - interrupt-parent + - interrupt-map + - interrupt-map-mask + - bus-range + - msi-map + - interrupt-controller + +unevaluatedProperties: false + +examples: + - | + + versal { + #address-cells = <2>; + #size-cells = <2>; + cpm_pcie: pcie@fca10000 { + compatible = "xlnx,versal-cpm-host-1.00"; + device_type = "pci"; + #address-cells = <3>; + #interrupt-cells = <1>; + #size-cells = <2>; + interrupts = <0 72 4>; + interrupt-parent = <&gic>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc_0 0>, + <0 0 0 2 &pcie_intc_0 1>, + <0 0 0 3 &pcie_intc_0 2>, + <0 0 0 4 &pcie_intc_0 3>; + bus-range = <0x00 0xff>; + ranges = <0x02000000 0x0 0xe0000000 0x0 0xe0000000 0x0 0x10000000>, + <0x43000000 0x80 0x00000000 0x80 0x00000000 0x0 0x80000000>; + msi-map = <0x0 &its_gic 0x0 0x10000>; + reg = <0x6 0x00000000 0x0 0x10000000>, + <0x0 0xfca10000 0x0 0x1000>; + reg-names = "cfg", "cpm_slcr"; + pcie_intc_0: interrupt-controller { + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + }; + }; + }; |