diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/device-mapper/dm-raid.txt | 1 | ||||
| -rwxr-xr-x | Documentation/devicetree/bindings/mfd/tps6507x.txt | 91 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/anatop-regulator.txt | 8 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt | 152 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/tps51632-regulator.txt | 27 | ||||
| -rw-r--r--[-rwxr-xr-x] | Documentation/hid/hid-sensor.txt | 0 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 2 | ||||
| -rw-r--r-- | Documentation/x86/boot.txt | 28 | ||||
| -rw-r--r-- | Documentation/x86/zero-page.txt | 4 |
9 files changed, 311 insertions, 2 deletions
diff --git a/Documentation/device-mapper/dm-raid.txt b/Documentation/device-mapper/dm-raid.txt index 728c38c242d6..56fb62b09fc5 100644 --- a/Documentation/device-mapper/dm-raid.txt +++ b/Documentation/device-mapper/dm-raid.txt @@ -141,3 +141,4 @@ Version History 1.2.0 Handle creation of arrays that contain failed devices. 1.3.0 Added support for RAID 10 1.3.1 Allow device replacement/rebuild for RAID 10 +1.3.2 Fix/improve redundancy checking for RAID10 diff --git a/Documentation/devicetree/bindings/mfd/tps6507x.txt b/Documentation/devicetree/bindings/mfd/tps6507x.txt new file mode 100755 index 000000000000..8fffa3c5ed40 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6507x.txt @@ -0,0 +1,91 @@ +TPS6507x Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps6507x" +- reg: I2C slave address +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the + given device need to be present. The definition for each of these nodes + is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2 +- xxx-supply: Input voltage supply regulator. + These entries are required if regulators are enabled for a device. + Missing of these properties can cause the regulator registration + fails. + If some of input supply is powered through battery or always-on + supply then also it is require to have these parameters with proper + node handle of always on power supply. + tps6507x: + vindcdc1_2-supply: VDCDC1 and VDCDC2 input. + vindcdc3-supply : VDCDC3 input. + vldo1_2-supply : VLDO1 and VLDO2 input. + +Regulator Optional properties: +- defdcdc_default: It's property of DCDC2 and DCDC3 regulators. + 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND. + 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH. + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps6507x@48 { + compatible = "ti,tps6507x"; + reg = <0x48>; + + vindcdc1_2-supply = <&vbat>; + vindcdc3-supply = <...>; + vinldo1_2-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdcdc1_reg: regulator@0 { + regulator-compatible = "VDCDC1"; + reg = <0>; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + }; + vdcdc2_reg: regulator@1 { + regulator-compatible = "VDCDC2"; + reg = <1>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + vdcdc3_reg: regulator@2 { + regulator-compatible = "VDCDC3"; + reg = <2>; + regulator-min-microvolt = <950000> + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + ldo1_reg: regulator@3 { + regulator-compatible = "LDO1"; + reg = <3>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1890000>; + regulator-always-on; + regulator-boot-on; + }; + ldo2_reg: regulator@4 { + regulator-compatible = "LDO2"; + reg = <4>; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1320000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 357758cb6e92..758eae24082a 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -9,6 +9,11 @@ Required properties: - anatop-min-voltage: Minimum voltage of this regulator - anatop-max-voltage: Maximum voltage of this regulator +Optional properties: +- anatop-delay-reg-offset: Anatop MFD step time register offset +- anatop-delay-bit-shift: Bit shift for the step time register +- anatop-delay-bit-width: Number of bits used in the step time register + Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -23,6 +28,9 @@ Example: anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <9>; anatop-vol-bit-width = <5>; + anatop-delay-reg-offset = <0x170>; + anatop-delay-bit-shift = <24>; + anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1300000>; diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt new file mode 100644 index 000000000000..a35ff99003a5 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -0,0 +1,152 @@ +* Samsung S5M8767 Voltage and Current Regulator + +The Samsung S5M8767 is a multi-function device which includes volatage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of s5m8767. + +Required properties: +- compatible: Should be "samsung,s5m8767-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck3 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck4 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + +[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s5m8767 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. +- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: + +- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of s5m8767 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_1.0V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + }; +The above regulator entries are defined in regulator bindings documentation +except op_mode description. + - op_mode: describes the different operating modes of the LDO's with + power mode change in SOC. The different possible values are, + 0 - always off mode + 1 - on in normal mode + 2 - low power mode + 3 - suspend mode + +The following are the names of the regulators that the s5m8767 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s5m8767. + + - LDOn + - valid values for n are 1 to 28 + - Example: LDO0, LD01, LDO28 + - BUCKn + - valid values for n are 1 to 9. + - Example: BUCK1, BUCK2, BUCK9 + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + s5m8767_pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck2-uses-gpio-dvs; + s5m8767,pmic-buck3-uses-gpio-dvs; + s5m8767,pmic-buck4-uses-gpio-dvs; + + s5m8767,pmic-buck-default-dvs-idx = <0>; + + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ + <&gpx0 1 1 0 0>, /* DVS2 */ + <&gpx0 2 1 0 0>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ + <&gpx2 4 1 0 0>, /* SET2 */ + <&gpx2 5 1 0 0>; /* SET3 */ + + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt new file mode 100644 index 000000000000..2f7e44a96414 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt @@ -0,0 +1,27 @@ +TPS51632 Voltage regulators + +Required properties: +- compatible: Must be "ti,tps51632" +- reg: I2C slave address + +Optional properties: +- ti,enable-pwm-dvfs: Enable the DVFS voltage control through the PWM interface. +- ti,dvfs-step-20mV: The 20mV step voltage when PWM DVFS enabled. Missing this + will set 10mV step voltage in PWM DVFS mode. In normal mode, the voltage + step is 10mV as per datasheet. + +Any property defined as part of the core regulator binding, defined in +regulator.txt, can also be used. + +Example: + + tps51632 { + compatible = "ti,tps51632"; + reg = <0x43>; + regulator-name = "tps51632-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + ti,enable-pwm-dvfs; + ti,dvfs-step-20mV; + }; diff --git a/Documentation/hid/hid-sensor.txt b/Documentation/hid/hid-sensor.txt index 948b0989c433..948b0989c433 100755..100644 --- a/Documentation/hid/hid-sensor.txt +++ b/Documentation/hid/hid-sensor.txt diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 363e348bff9b..6c723811c0a0 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2438,7 +2438,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. real-time workloads. It can also improve energy efficiency for asymmetric multiprocessors. - rcu_nocbs_poll [KNL,BOOT] + rcu_nocb_poll [KNL,BOOT] Rather than requiring that offloaded CPUs (specified by rcu_nocbs= above) explicitly awaken the corresponding "rcuoN" kthreads, diff --git a/Documentation/x86/boot.txt b/Documentation/x86/boot.txt index 406d82d5d2bb..b443f1de0e5a 100644 --- a/Documentation/x86/boot.txt +++ b/Documentation/x86/boot.txt @@ -57,6 +57,10 @@ Protocol 2.10: (Kernel 2.6.31) Added a protocol for relaxed alignment Protocol 2.11: (Kernel 3.6) Added a field for offset of EFI handover protocol entry point. +Protocol 2.12: (Kernel 3.8) Added the xloadflags field and extension fields + to struct boot_params for for loading bzImage and ramdisk + above 4G in 64bit. + **** MEMORY LAYOUT The traditional memory map for the kernel loader, used for Image or @@ -182,7 +186,7 @@ Offset Proto Name Meaning 0230/4 2.05+ kernel_alignment Physical addr alignment required for kernel 0234/1 2.05+ relocatable_kernel Whether kernel is relocatable or not 0235/1 2.10+ min_alignment Minimum alignment, as a power of two -0236/2 N/A pad3 Unused +0236/2 2.12+ xloadflags Boot protocol option flags 0238/4 2.06+ cmdline_size Maximum size of the kernel command line 023C/4 2.07+ hardware_subarch Hardware subarchitecture 0240/8 2.07+ hardware_subarch_data Subarchitecture-specific data @@ -386,6 +390,7 @@ Protocol: 2.00+ F Special (0xFF = undefined) 10 Reserved 11 Minimal Linux Bootloader <http://sebastian-plotz.blogspot.de> + 12 OVMF UEFI virtualization stack Please contact <hpa@zytor.com> if you need a bootloader ID value assigned. @@ -582,6 +587,27 @@ Protocol: 2.10+ misaligned kernel. Therefore, a loader should typically try each power-of-two alignment from kernel_alignment down to this alignment. +Field name: xloadflags +Type: read +Offset/size: 0x236/2 +Protocol: 2.12+ + + This field is a bitmask. + + Bit 0 (read): XLF_KERNEL_64 + - If 1, this kernel has the legacy 64-bit entry point at 0x200. + + Bit 1 (read): XLF_CAN_BE_LOADED_ABOVE_4G + - If 1, kernel/boot_params/cmdline/ramdisk can be above 4G. + + Bit 2 (read): XLF_EFI_HANDOVER_32 + - If 1, the kernel supports the 32-bit EFI handoff entry point + given at handover_offset. + + Bit 3 (read): XLF_EFI_HANDOVER_64 + - If 1, the kernel supports the 64-bit EFI handoff entry point + given at handover_offset + 0x200. + Field name: cmdline_size Type: read Offset/size: 0x238/4 diff --git a/Documentation/x86/zero-page.txt b/Documentation/x86/zero-page.txt index cf5437deda81..199f453cb4de 100644 --- a/Documentation/x86/zero-page.txt +++ b/Documentation/x86/zero-page.txt @@ -19,6 +19,9 @@ Offset Proto Name Meaning 090/010 ALL hd1_info hd1 disk parameter, OBSOLETE!! 0A0/010 ALL sys_desc_table System description table (struct sys_desc_table) 0B0/010 ALL olpc_ofw_header OLPC's OpenFirmware CIF and friends +0C0/004 ALL ext_ramdisk_image ramdisk_image high 32bits +0C4/004 ALL ext_ramdisk_size ramdisk_size high 32bits +0C8/004 ALL ext_cmd_line_ptr cmd_line_ptr high 32bits 140/080 ALL edid_info Video mode setup (struct edid_info) 1C0/020 ALL efi_info EFI 32 information (struct efi_info) 1E0/004 ALL alk_mem_k Alternative mem check, in KB @@ -27,6 +30,7 @@ Offset Proto Name Meaning 1E9/001 ALL eddbuf_entries Number of entries in eddbuf (below) 1EA/001 ALL edd_mbr_sig_buf_entries Number of entries in edd_mbr_sig_buffer (below) +1EF/001 ALL sentinel Used to detect broken bootloaders 290/040 ALL edd_mbr_sig_buffer EDD MBR signatures 2D0/A00 ALL e820_map E820 memory map table (array of struct e820entry) |