diff options
Diffstat (limited to 'Documentation/hwmon/lt7182s.rst')
| -rw-r--r-- | Documentation/hwmon/lt7182s.rst | 92 |
1 files changed, 92 insertions, 0 deletions
diff --git a/Documentation/hwmon/lt7182s.rst b/Documentation/hwmon/lt7182s.rst new file mode 100644 index 000000000000..f7268311b191 --- /dev/null +++ b/Documentation/hwmon/lt7182s.rst @@ -0,0 +1,92 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver lt7182s +===================== + +Supported chips: + + * ADI LT7182S + + Prefix: 'lt7182s' + + Addresses scanned: - + + Datasheet: https://www.analog.com/en/products/lt7182s.html + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +LT7182S is a Dual Channel 6A, 20V PolyPhase Step-Down Silent Switcher with +Digital Power System Management support. + + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +Example: the following commands will load the driver for a LT7182S +at address 0x4f on I2C bus #4:: + + # modprobe lt7182s + # echo lt7182s 0x4f > /sys/bus/i2c/devices/i2c-4/new_device + +It can also be instantiated by declaring an entry in device tree. + + +Sysfs attributes +---------------- + +======================= ==================================== +curr[1-2]_label "iin[12]" +curr[1-2]_input Measured input current +curr[1-2]_max Maximum input current +curr[1-2]_max_alarm Current high alarm + +curr[3-4]_label "iout[1-2]" +curr[3-4]_input Measured output current +curr[3-4]_highest Highest measured output current +curr[3-4]_max Maximum output current +curr[3-4]_max_alarm Output current high alarm + +in[1-2]_label "vin[12]" +in[1-2]_input Measured input voltage +in[1-2]_highest Highest measured input voltage +in[1-2]_crit Critical maximum input voltage +in[1-2]_crit_alarm Input voltage critical high alarm +in[1-2]_min Minimum input voltage +in[1-2]_min_alarm Input voltage low alarm +in[1-2]_rated_min Rated minimum input voltage +in[1-2]_rated_max Rated maximum input voltage +in1_reset_history Write to reset history for all attributes + +in[3-5]_label "vmon[1-3]" +in[3-5]_input Measured voltage on ITH1/ITH2/EXTVCC pins + Only available if enabled with MFR_ADC_CONTROL_LT7182S + command. + +in[3-4|6-7]_label "vout[1-2]" +in[3-4|6-7]_input Measured output voltage +in[3-4|6-7]_highest Highest measured output voltage +in[3-4|6-7]_lcrit Critical minimum output voltage +in[3-4|6-7]_lcrit_alarm Output voltage critical low alarm +in[3-4|6-7]_min Minimum output voltage +in[3-4|6-7]_max_alarm Output voltage low alarm +in[3-4|6-7]_max Maximum output voltage +in[3-4|6-7]_max_alarm Output voltage high alarm +in[3-4|6-7]_crit Critical maximum output voltage +in[3-4|6-7]_crit_alarm Output voltage critical high alarm + +power[1-2]_label "pout[1-2]" +power[1-2]_input Measured output power + +temp1_input Measured temperature +temp1_crit Critical high temperature +temp1_crit_alarm Chip temperature critical high alarm +temp1_max Maximum temperature +temp1_max_alarm Chip temperature high alarm +======================= ==================================== |