diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
7 files changed, 115 insertions, 15 deletions
diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index 2390e4e9c84c..eaf7e9b7ce6b 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -7,33 +7,26 @@ Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. - reg: offset and length of the partial USB 2.0 Host register block. -- reg-names: must be "usb2_host". - clocks: clock phandle and specifier pair(s). - #phy-cells: see phy-bindings.txt in the same directory, must be <0>. Optional properties: To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are -combined, the device tree node should set HSUSB properties to reg and reg-names -properties. This is because HSUSB has registers to select USB 2.0 host or -peripheral at that channel: -- reg: offset and length of the partial HSUSB register block. -- reg-names: must be "hsusb". +combined, the device tree node should set interrupt properties to use the +channel as USB OTG: - interrupts: interrupt specifier for the PHY. Example (R-Car H3): usb-phy@ee080200 { compatible = "renesas,usb2-phy-r8a7795"; - reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>; - reg-names = "usb2_host", "hsusb"; + reg = <0 0xee080200 0 0x700>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>, - <&mstp7_clks R8A7795_CLK_HSUSB>; + clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; usb-phy@ee0a0200 { compatible = "renesas,usb2-phy-r8a7795"; reg = <0 0xee0a0200 0 0x700>; - reg-names = "usb2_host"; clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt new file mode 100644 index 000000000000..50c4f9b00adf --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt @@ -0,0 +1,22 @@ +Rockchip specific extensions to the Analogix Display Port PHY +------------------------------------ + +Required properties: +- compatible : should be one of the following supported values: + - "rockchip.rk3288-dp-phy" +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. +- clock-names: from common clock binding: + Required elements: "24m" +- rockchip,grf: phandle to the syscon managing the "general register files" +- #phy-cells : from the generic PHY bindings, must be 0; + +Example: + +edp_phy: edp-phy { + compatible = "rockchip,rk3288-dp-phy"; + rockchip,grf = <&grf>; + clocks = <&cru SCLK_EDP_24M>; + clock-names = "24m"; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt new file mode 100644 index 000000000000..61916f15a949 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -0,0 +1,19 @@ +Rockchip EMMC PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-emmc-phy + - rockchip,grf : phandle to the syscon managing the "general + register files" + - #phy-cells: must be 0 + - reg: PHY configure reg address offset in "general + register files" + +Example: + +emmcphy: phy { + compatible = "rockchip,rk3399-emmc-phy"; + rockchip,grf = <&grf>; + reg = <0xf780>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 781296bfbe4f..1084e2bcbe1c 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -2,7 +2,14 @@ Required properties: - compatible: should be one of: + "fsl,imx23-usb" "fsl,imx27-usb" + "fsl,imx28-usb" + "fsl,imx6q-usb" + "fsl,imx6sl-usb" + "fsl,imx6sx-usb" + "fsl,imx6ul-usb" + "fsl,imx7d-usb" "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" @@ -53,6 +60,22 @@ Optional properties: be specified. - phy-clkgate-delay-us: the delay time (us) between putting the PHY into low power mode and gating the PHY clock. +- non-zero-ttctrl-ttha: after setting this property, the value of register + ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it is + recommended that consult with your IC engineer before setting this value. + On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this + property only affects siTD. + If this property is not set, the max packet size is 1023 bytes, and if + the total of packet size for pervious transactions are more than 256 bytes, + it can't accept any transactions within this frame. The use case is single + transaction, but higher frame rate. + If this property is set, the max packet size is 188 bytes, it can handle + more transactions than above case, it can accept transactions until it + considers the left room size within frame is less than 188 bytes, software + needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple transactions, but + less frame rate. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 221368207ca4..20a68bf2b4e7 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -8,6 +8,8 @@ Required properties: - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; + - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; + - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt new file mode 100644 index 000000000000..1c35e7b665e1 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -0,0 +1,28 @@ +Generic USB Device Properties + +Usually, we only use device tree for hard wired USB device. +The reference binding doc is from: +http://www.firmware.org/1275/bindings/usb/usb-1_0.ps + +Required properties: +- compatible: usbVID,PID. The textual representation of VID, PID shall + be in lower case hexadecimal with leading zeroes suppressed. The + other compatible strings from the above standard binding could also + be used, but a device adhering to this binding may leave out all except + for usbVID,PID. +- reg: the port number which this device is connecting to, the range + is 1-31. + +Example: + +&usb1 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + hub: genesys@1 { + compatible = "usb5e3,608"; + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 082573289f1e..6a17aa85c4d5 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,10 +1,23 @@ USB xHCI controllers Required properties: - - compatible: should be one of "generic-xhci", - "marvell,armada-375-xhci", "marvell,armada-380-xhci", - "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793", - "renesas,xhci-r8a7795" (deprecated: "xhci-platform"). + - compatible: should be one or more of + + - "generic-xhci" for generic XHCI device + - "marvell,armada-375-xhci" for Armada 375 SoCs + - "marvell,armada-380-xhci" for Armada 38x SoCs + - "renesas,xhci-r8a7790" for r8a7790 SoC + - "renesas,xhci-r8a7791" for r8a7791 SoC + - "renesas,xhci-r8a7793" for r8a7793 SoC + - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "xhci-platform" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. |