diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa')
5 files changed, 464 insertions, 110 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml index 6107189d276a..2abd036578d1 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml @@ -46,4 +46,10 @@ $defs: $ref: dsa-port.yaml# unevaluatedProperties: false +oneOf: + - required: + - ports + - required: + - ethernet-ports + ... diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml new file mode 100644 index 000000000000..4f1adf00431a --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6060.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6060 DSA switch + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + +description: + The Marvell MV88E6060 switch has been produced and sold by Marvell + since at least 2008. The switch has one pin ADDR4 that controls the + MDIO address of the switch to be 0x10 or 0x00, and on the MDIO bus + connected to the switch, the PHYs inside the switch appear as + independent devices on address 0x00-0x04 or 0x10-0x14, so in difference + from many other DSA switches this switch does not have an internal + MDIO bus for the PHY devices. + +properties: + compatible: + const: marvell,mv88e6060 + description: + The MV88E6060 is the oldest Marvell DSA switch product, and + as such a bit limited in features compared to later hardware. + + reg: + maxItems: 1 + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@16 { + compatible = "marvell,mv88e6060"; + reg = <16>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + reg = <0>; + label = "lan1"; + }; + ethernet-port@1 { + reg = <1>; + label = "lan2"; + }; + ethernet-port@2 { + reg = <2>; + label = "lan3"; + }; + ethernet-port@3 { + reg = <3>; + label = "lan4"; + }; + ethernet-port@5 { + reg = <5>; + phy-mode = "rev-mii"; + ethernet = <ðc>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml new file mode 100644 index 000000000000..19f15bdd1c97 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml @@ -0,0 +1,337 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6xxx DSA switch family + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + +description: + The Marvell MV88E6xxx switch series has been produced and sold + by Marvell since at least 2008. The switch has a few compatibles which + just indicate the base address of the switch, then operating systems + can investigate switch ID registers to find out which actual version + of the switch it is dealing with. + +properties: + compatible: + oneOf: + - enum: + - marvell,mv88e6085 + - marvell,mv88e6190 + - marvell,mv88e6250 + description: | + marvell,mv88e6085: This switch uses base address 0x10. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6085" should be + specified. This includes the following list of MV88Exxxx switches: + 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176, + 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352 + marvell,mv88e6190: This switch uses base address 0x00. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6190" should be + specified. This includes the following list of MV88Exxxx switches: + 6190, 6190X, 6191, 6290, 6361, 6390, 6390X + marvell,mv88e6250: This switch uses base address 0x08 or 0x18. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6250" should be + specified. This includes the following list of MV88Exxxx switches: + 6220, 6250 + - items: + - const: marvell,turris-mox-mv88e6085 + - const: marvell,mv88e6085 + - items: + - const: marvell,turris-mox-mv88e6190 + - const: marvell,mv88e6190 + + reg: + maxItems: 1 + + eeprom-length: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Set to the length of an EEPROM connected to the switch. Must be + set if the switch can not detect the presence and/or size of a connected + EEPROM, otherwise optional. + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + + interrupts: + description: The switch provides an external interrupt line, but it is + not always used by target systems. + maxItems: 1 + + interrupt-controller: + description: The switch has an internal interrupt controller used by + the different sub-blocks. + + '#interrupt-cells': + description: The internal interrupt controller only supports triggering + on active high level interrupts so the second cell must alway be set to + IRQ_TYPE_LEVEL_HIGH. + const: 2 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches have an varying combination of + internal and external MDIO buses, in some cases a combined bus that + can be used both internally and externally. This node is for the + primary bus, used internally and sometimes also externally. + + mdio-external: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches that have a separate external + MDIO bus use this port to access external components on the MDIO bus. + + properties: + compatible: + const: marvell,mv88e6xxx-mdio-external + + required: + - compatible + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + sw_phy0: ethernet-phy@0 { + reg = <0x0>; + }; + + sw_phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + sw_phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + sw_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + }; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + reg = <0>; + label = "lan4"; + phy-handle = <&sw_phy0>; + phy-mode = "internal"; + }; + + ethernet-port@1 { + reg = <1>; + label = "lan3"; + phy-handle = <&sw_phy1>; + phy-mode = "internal"; + }; + + ethernet-port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&sw_phy2>; + phy-mode = "internal"; + }; + + ethernet-port@3 { + reg = <3>; + label = "lan1"; + phy-handle = <&sw_phy3>; + phy-mode = "internal"; + }; + + ethernet-port@5 { + reg = <5>; + ethernet = <&fec>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "marvell,mv88e6190"; + #interrupt-cells = <2>; + interrupt-controller; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&switch_interrupt_pins>; + pinctrl-names = "default"; + reg = <0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + switch0phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + switch0phy3: ethernet-phy@3 { + reg = <0x3>; + }; + + switch0phy4: ethernet-phy@4 { + reg = <0x4>; + }; + + switch0phy5: ethernet-phy@5 { + reg = <0x5>; + }; + + switch0phy6: ethernet-phy@6 { + reg = <0x6>; + }; + + switch0phy7: ethernet-phy@7 { + reg = <0x7>; + }; + + switch0phy8: ethernet-phy@8 { + reg = <0x8>; + }; + }; + + mdio-external { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@b { + reg = <0xb>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; + + phy2: ethernet-phy@c { + reg = <0xc>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; + }; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + ethernet = <ð0>; + phy-mode = "rgmii"; + reg = <0>; + + fixed-link { + full-duplex; + pause; + speed = <1000>; + }; + }; + + ethernet-port@1 { + label = "lan1"; + phy-handle = <&switch0phy1>; + reg = <1>; + }; + + ethernet-port@2 { + label = "lan2"; + phy-handle = <&switch0phy2>; + reg = <2>; + }; + + ethernet-port@3 { + label = "lan3"; + phy-handle = <&switch0phy3>; + reg = <3>; + }; + + ethernet-port@4 { + label = "lan4"; + phy-handle = <&switch0phy4>; + reg = <4>; + }; + + ethernet-port@5 { + label = "lan5"; + phy-handle = <&switch0phy5>; + reg = <5>; + }; + + ethernet-port@6 { + label = "lan6"; + phy-handle = <&switch0phy6>; + reg = <6>; + }; + + ethernet-port@7 { + label = "lan7"; + phy-handle = <&switch0phy7>; + reg = <7>; + }; + + ethernet-port@8 { + label = "lan8"; + phy-handle = <&switch0phy8>; + reg = <8>; + }; + + ethernet-port@9 { + /* 88X3310P external phy */ + label = "lan9"; + phy-handle = <&phy1>; + phy-mode = "xaui"; + reg = <9>; + }; + + ethernet-port@a { + /* 88X3310P external phy */ + label = "lan10"; + phy-handle = <&phy2>; + phy-mode = "xaui"; + reg = <0xa>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt deleted file mode 100644 index 6ec0c181b6db..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ /dev/null @@ -1,109 +0,0 @@ -Marvell DSA Switch Device Tree Bindings ---------------------------------------- - -WARNING: This binding is currently unstable. Do not program it into a -FLASH never to be changed again. Once this binding is stable, this -warning will be removed. - -If you need a stable binding, use the old dsa.txt binding. - -Marvell Switches are MDIO devices. The following properties should be -placed as a child node of an mdio device. - -The properties described here are those specific to Marvell devices. -Additional required and optional properties can be found in dsa.txt. - -The compatibility string is used only to find an identification register, -which is at a different MDIO base address in different switch families. -- "marvell,mv88e6085" : Switch has base address 0x10. Use with models: - 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, - 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321, - 6341, 6350, 6351, 6352 -- "marvell,mv88e6190" : Switch has base address 0x00. Use with models: - 6190, 6190X, 6191, 6290, 6361, 6390, 6390X -- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: - 6220, 6250 - -Required properties: -- compatible : Should be one of "marvell,mv88e6085", - "marvell,mv88e6190" or "marvell,mv88e6250" as - indicated above -- reg : Address on the MII bus for the switch. - -Optional properties: - -- reset-gpios : Should be a gpio specifier for a reset line -- interrupts : Interrupt from the switch -- interrupt-controller : Indicates the switch is itself an interrupt - controller. This is used for the PHY interrupts. -#interrupt-cells = <2> : Controller uses two cells, number and flag -- eeprom-length : Set to the length of an EEPROM connected to the - switch. Must be set if the switch can not detect - the presence and/or size of a connected EEPROM, - otherwise optional. -- mdio : Container of PHY and devices on the switches MDIO - bus. -- mdio? : Container of PHYs and devices on the external MDIO - bus. The node must contains a compatible string of - "marvell,mv88e6xxx-mdio-external" - -Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6085"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6190"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - - mdio1 { - compatible = "marvell,mv88e6xxx-mdio-external"; - #address-cells = <1>; - #size-cells = <0>; - switch1phy9: switch1phy0@9 { - reg = <9>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml index b3029c64d0d5..c963dc09e8e1 100644 --- a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml +++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml @@ -11,7 +11,6 @@ maintainers: - Woojung Huh <Woojung.Huh@microchip.com> allOf: - - $ref: dsa.yaml#/$defs/ethernet-ports - $ref: /schemas/spi/spi-peripheral-props.yaml# properties: @@ -78,6 +77,39 @@ required: - compatible - reg +if: + not: + properties: + compatible: + enum: + - microchip,ksz8863 + - microchip,ksz8873 +then: + $ref: dsa.yaml#/$defs/ethernet-ports +else: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-2]$": + $ref: dsa-port.yaml# + unevaluatedProperties: false + properties: + microchip,rmii-clk-internal: + $ref: /schemas/types.yaml#/definitions/flag + description: + When ksz88x3 is acting as clock provier (via REFCLKO) it + can select between internal and external RMII reference + clock. Internal reference clock means that the clock for + the RMII of ksz88x3 is provided by the ksz88x3 internally + and the REFCLKI pin is unconnected. For the external + reference clock, the clock needs to be fed back to ksz88x3 + via REFCLKI. + If microchip,rmii-clk-internal is set, ksz88x3 will provide + rmii reference clock internally, otherwise reference clock + should be provided externally. + dependencies: + microchip,rmii-clk-internal: [ethernet] + unevaluatedProperties: false examples: |