diff options
Diffstat (limited to 'Documentation/RCU')
| -rw-r--r-- | Documentation/RCU/torture.rst | 89 |
1 files changed, 85 insertions, 4 deletions
diff --git a/Documentation/RCU/torture.rst b/Documentation/RCU/torture.rst index a90147713062..0316ba0c6922 100644 --- a/Documentation/RCU/torture.rst +++ b/Documentation/RCU/torture.rst @@ -206,7 +206,11 @@ values for memory may require disabling the callback-flooding tests using the --bootargs parameter discussed below. Sometimes additional debugging is useful, and in such cases the --kconfig -parameter to kvm.sh may be used, for example, ``--kconfig 'CONFIG_KASAN=y'``. +parameter to kvm.sh may be used, for example, ``--kconfig 'CONFIG_RCU_EQS_DEBUG=y'``. +In addition, there are the --gdb, --kasan, and --kcsan parameters. +Note that --gdb limits you to one scenario per kvm.sh run and requires +that you have another window open from which to run ``gdb`` as instructed +by the script. Kernel boot arguments can also be supplied, for example, to control rcutorture's module parameters. For example, to test a change to RCU's @@ -219,10 +223,17 @@ require disabling rcutorture's callback-flooding tests:: --bootargs 'rcutorture.fwd_progress=0' Sometimes all that is needed is a full set of kernel builds. This is -what the --buildonly argument does. +what the --buildonly parameter does. -Finally, the --trust-make argument allows each kernel build to reuse what -it can from the previous kernel build. +The --duration parameter can override the default run time of 30 minutes. +For example, ``--duration 2d`` would run for two days, ``--duration 3h`` +would run for three hours, ``--duration 5m`` would run for five minutes, +and ``--duration 45s`` would run for 45 seconds. This last can be useful +for tracking down rare boot-time failures. + +Finally, the --trust-make parameter allows each kernel build to reuse what +it can from the previous kernel build. Please note that without the +--trust-make parameter, your tags files may be demolished. There are additional more arcane arguments that are documented in the source code of the kvm.sh script. @@ -291,3 +302,73 @@ the following summary at the end of the run on a 12-CPU system:: TREE07 ------- 167347 GPs (30.9902/s) [rcu: g1079021 f0x0 ] n_max_cbs: 478732 CPU count limited from 16 to 12 TREE09 ------- 752238 GPs (139.303/s) [rcu: g13075057 f0x0 ] n_max_cbs: 99011 + + +Repeated Runs +============= + +Suppose that you are chasing down a rare boot-time failure. Although you +could use kvm.sh, doing so will rebuild the kernel on each run. If you +need (say) 1,000 runs to have confidence that you have fixed the bug, +these pointless rebuilds can become extremely annoying. + +This is why kvm-again.sh exists. + +Suppose that a previous kvm.sh run left its output in this directory:: + + tools/testing/selftests/rcutorture/res/2022.11.03-11.26.28 + +Then this run can be re-run without rebuilding as follow: + + kvm-again.sh tools/testing/selftests/rcutorture/res/2022.11.03-11.26.28 + +A few of the original run's kvm.sh parameters may be overridden, perhaps +most notably --duration and --bootargs. For example:: + + kvm-again.sh tools/testing/selftests/rcutorture/res/2022.11.03-11.26.28 \ + --duration 45s + +would re-run the previous test, but for only 45 seconds, thus facilitating +tracking down the aforementioned rare boot-time failure. + + +Distributed Runs +================ + +Although kvm.sh is quite useful, its testing is confined to a single +system. It is not all that hard to use your favorite framework to cause +(say) 5 instances of kvm.sh to run on your 5 systems, but this will very +likely unnecessarily rebuild kernels. In addition, manually distributing +the desired rcutorture scenarios across the available systems can be +painstaking and error-prone. + +And this is why the kvm-remote.sh script exists. + +If you the following command works:: + + ssh system0 date + +and if it also works for system1, system2, system3, system4, and system5, +and all of these systems have 64 CPUs, you can type:: + + kvm-remote.sh "system0 system1 system2 system3 system4 system5" \ + --cpus 64 --duration 8h --configs "5*CFLIST" + +This will build each default scenario's kernel on the local system, then +spread each of five instances of each scenario over the systems listed, +running each scenario for eight hours. At the end of the runs, the +results will be gathered, recorded, and printed. Most of the parameters +that kvm.sh will accept can be passed to kvm-remote.sh, but the list of +systems must come first. + +The kvm.sh ``--dryrun scenarios`` argument is useful for working out +how many scenarios may be run in one batch across a group of systems. + +You can also re-run a previous remote run in a manner similar to kvm.sh: + + kvm-remote.sh "system0 system1 system2 system3 system4 system5" \ + tools/testing/selftests/rcutorture/res/2022.11.03-11.26.28-remote \ + --duration 24h + +In this case, most of the kvm-again.sh parmeters may be supplied following +the pathname of the old run-results directory. |