summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt77
-rw-r--r--Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml125
-rw-r--r--Documentation/devicetree/bindings/input/touchscreen/goodix.yaml2
-rw-r--r--drivers/input/serio/i8042-x86ia64io.h11
-rw-r--r--drivers/input/touchscreen/elants_i2c.c1
-rw-r--r--drivers/input/touchscreen/goodix.c608
-rw-r--r--drivers/input/touchscreen/of_touchscreen.c35
-rw-r--r--include/uapi/linux/input-event-codes.h2
8 files changed, 651 insertions, 210 deletions
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
deleted file mode 100644
index 0e57315e9cbd..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
+++ /dev/null
@@ -1,77 +0,0 @@
-FocalTech EDT-FT5x06 Polytouch driver
-=====================================
-
-There are 5 variants of the chip for various touch panel sizes
-FT5206GE1 2.8" .. 3.8"
-FT5306DE4 4.3" .. 7"
-FT5406EE8 7" .. 8.9"
-FT5506EEG 7" .. 8.9"
-FT5726NEI 5.7” .. 11.6"
-
-The software interface is identical for all those chips, so that
-currently there is no need for the driver to distinguish between the
-different chips. Nevertheless distinct compatible strings are used so
-that a distinction can be added if necessary without changing the DT
-bindings.
-
-
-Required properties:
- - compatible: "edt,edt-ft5206"
- or: "edt,edt-ft5306"
- or: "edt,edt-ft5406"
- or: "edt,edt-ft5506"
- or: "evervision,ev-ft5726"
- or: "focaltech,ft6236"
-
- - reg: I2C slave address of the chip (0x38)
- - interrupts: interrupt specification for the touchdetect
- interrupt
-
-Optional properties:
- - reset-gpios: GPIO specification for the RESET input
- - wake-gpios: GPIO specification for the WAKE input
- - vcc-supply: Regulator that supplies the touchscreen
-
- - pinctrl-names: should be "default"
- - pinctrl-0: a phandle pointing to the pin settings for the
- control gpios
-
- - wakeup-source: If present the device will act as wakeup-source
-
- - threshold: allows setting the "click"-threshold in the range
- from 0 to 80.
-
- - gain: allows setting the sensitivity in the range from 0 to
- 31. Note that lower values indicate higher
- sensitivity.
-
- - offset: allows setting the edge compensation in the range from
- 0 to 31.
-
- - offset-x: Same as offset, but applies only to the horizontal position.
- Range from 0 to 80, only supported by evervision,ev-ft5726
- devices.
-
- - offset-y: Same as offset, but applies only to the vertical position.
- Range from 0 to 80, only supported by evervision,ev-ft5726
- devices.
-
- - touchscreen-size-x : See touchscreen.txt
- - touchscreen-size-y : See touchscreen.txt
- - touchscreen-fuzz-x : See touchscreen.txt
- - touchscreen-fuzz-y : See touchscreen.txt
- - touchscreen-inverted-x : See touchscreen.txt
- - touchscreen-inverted-y : See touchscreen.txt
- - touchscreen-swapped-x-y : See touchscreen.txt
-
-Example:
- polytouch: edt-ft5x06@38 {
- compatible = "edt,edt-ft5406", "edt,edt-ft5x06";
- reg = <0x38>;
- pinctrl-names = "default";
- pinctrl-0 = <&edt_ft5x06_pins>;
- interrupt-parent = <&gpio2>;
- interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
- reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
- wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
- };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml
new file mode 100644
index 000000000000..8d58709d4b47
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml
@@ -0,0 +1,125 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/edt-ft5x06.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: FocalTech EDT-FT5x06 Polytouch Bindings
+
+description: |
+ There are 5 variants of the chip for various touch panel sizes
+ FT5206GE1 2.8" .. 3.8"
+ FT5306DE4 4.3" .. 7"
+ FT5406EE8 7" .. 8.9"
+ FT5506EEG 7" .. 8.9"
+ FT5726NEI 5.7” .. 11.6"
+
+maintainers:
+ - Dmitry Torokhov <dmitry.torokhov@gmail.com>
+
+allOf:
+ - $ref: touchscreen.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - evervision,ev-ft5726
+
+ then:
+ properties:
+ offset-x: true
+ offset-y: true
+
+properties:
+ compatible:
+ enum:
+ - edt,edt-ft5206
+ - edt,edt-ft5306
+ - edt,edt-ft5406
+ - edt,edt-ft5506
+ - evervision,ev-ft5726
+ - focaltech,ft6236
+
+ reg:
+ const: 0x38
+
+ interrupts:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+
+ wake-gpios:
+ maxItems: 1
+
+ wakeup-source: true
+
+ vcc-supply:
+ maxItems: 1
+
+ gain:
+ description: Allows setting the sensitivity in the range from 0 to 31.
+ Note that lower values indicate higher sensitivity.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 31
+
+ offset:
+ description: Allows setting the edge compensation in the range from 0 to 31.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 31
+
+ offset-x:
+ description: Same as offset, but applies only to the horizontal position.
+ Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 80
+
+ offset-y:
+ description: Same as offset, but applies only to the vertical position.
+ Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 80
+
+ touchscreen-size-x: true
+ touchscreen-size-y: true
+ touchscreen-fuzz-x: true
+ touchscreen-fuzz-y: true
+ touchscreen-inverted-x: true
+ touchscreen-inverted-y: true
+ touchscreen-swapped-x-y: true
+ interrupt-controller: true
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ i2c@00000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ edt-ft5x06@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml b/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
index c99ed3934d7e..c8ea9434c9cc 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
@@ -21,6 +21,8 @@ properties:
- goodix,gt911
- goodix,gt9110
- goodix,gt912
+ - goodix,gt9147
+ - goodix,gt917s
- goodix,gt927
- goodix,gt9271
- goodix,gt928
diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h
index dc974c288e88..08e919dbeb5d 100644
--- a/drivers/input/serio/i8042-x86ia64io.h
+++ b/drivers/input/serio/i8042-x86ia64io.h
@@ -530,6 +530,17 @@ static const struct dmi_system_id __initconst i8042_dmi_nomux_table[] = {
DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo LaVie Z"),
},
},
+ {
+ /*
+ * Acer Aspire 5738z
+ * Touchpad stops working in mux mode when dis- + re-enabled
+ * with the touchpad enable/disable toggle hotkey
+ */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5738"),
+ },
+ },
{ }
};
diff --git a/drivers/input/touchscreen/elants_i2c.c b/drivers/input/touchscreen/elants_i2c.c
index 491179967b29..14c577c16b16 100644
--- a/drivers/input/touchscreen/elants_i2c.c
+++ b/drivers/input/touchscreen/elants_i2c.c
@@ -1309,6 +1309,7 @@ static int elants_i2c_probe(struct i2c_client *client,
input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->x_res);
input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->y_res);
+ input_abs_set_res(ts->input, ABS_MT_TOUCH_MAJOR, 1);
error = input_register_device(ts->input);
if (error) {
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 0403102e807e..02c75ea385e0 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -29,33 +29,6 @@
#include <linux/of.h>
#include <asm/unaligned.h>
-struct goodix_ts_data;
-
-struct goodix_chip_data {
- u16 config_addr;
- int config_len;
- int (*check_config)(struct goodix_ts_data *, const struct firmware *);
-};
-
-struct goodix_ts_data {
- struct i2c_client *client;
- struct input_dev *input_dev;
- const struct goodix_chip_data *chip;
- struct touchscreen_properties prop;
- unsigned int max_touch_num;
- unsigned int int_trigger_type;
- struct regulator *avdd28;
- struct regulator *vddio;
- struct gpio_desc *gpiod_int;
- struct gpio_desc *gpiod_rst;
- u16 id;
- u16 version;
- const char *cfg_name;
- struct completion firmware_loading_complete;
- unsigned long irq_flags;
- unsigned int contact_size;
-};
-
#define GOODIX_GPIO_INT_NAME "irq"
#define GOODIX_GPIO_RST_NAME "reset"
@@ -65,10 +38,13 @@ struct goodix_ts_data {
#define GOODIX_CONTACT_SIZE 8
#define GOODIX_MAX_CONTACT_SIZE 9
#define GOODIX_MAX_CONTACTS 10
+#define GOODIX_MAX_KEYS 7
-#define GOODIX_CONFIG_MAX_LENGTH 240
+#define GOODIX_CONFIG_MIN_LENGTH 186
#define GOODIX_CONFIG_911_LENGTH 186
#define GOODIX_CONFIG_967_LENGTH 228
+#define GOODIX_CONFIG_GT9X_LENGTH 240
+#define GOODIX_CONFIG_MAX_LENGTH 240
/* Register defines */
#define GOODIX_REG_COMMAND 0x8040
@@ -80,39 +56,118 @@ struct goodix_ts_data {
#define GOODIX_REG_ID 0x8140
#define GOODIX_BUFFER_STATUS_READY BIT(7)
+#define GOODIX_HAVE_KEY BIT(4)
#define GOODIX_BUFFER_STATUS_TIMEOUT 20
#define RESOLUTION_LOC 1
#define MAX_CONTACTS_LOC 5
#define TRIGGER_LOC 6
+/* Our special handling for GPIO accesses through ACPI is x86 specific */
+#if defined CONFIG_X86 && defined CONFIG_ACPI
+#define ACPI_GPIO_SUPPORT
+#endif
+
+struct goodix_ts_data;
+
+enum goodix_irq_pin_access_method {
+ IRQ_PIN_ACCESS_NONE,
+ IRQ_PIN_ACCESS_GPIO,
+ IRQ_PIN_ACCESS_ACPI_GPIO,
+ IRQ_PIN_ACCESS_ACPI_METHOD,
+};
+
+struct goodix_chip_data {
+ u16 config_addr;
+ int config_len;
+ int (*check_config)(struct goodix_ts_data *ts, const u8 *cfg, int len);
+ void (*calc_config_checksum)(struct goodix_ts_data *ts);
+};
+
+struct goodix_chip_id {
+ const char *id;
+ const struct goodix_chip_data *data;
+};
+
+#define GOODIX_ID_MAX_LEN 4
+
+struct goodix_ts_data {
+ struct i2c_client *client;
+ struct input_dev *input_dev;
+ const struct goodix_chip_data *chip;
+ struct touchscreen_properties prop;
+ unsigned int max_touch_num;
+ unsigned int int_trigger_type;
+ struct regulator *avdd28;
+ struct regulator *vddio;
+ struct gpio_desc *gpiod_int;
+ struct gpio_desc *gpiod_rst;
+ int gpio_count;
+ int gpio_int_idx;
+ char id[GOODIX_ID_MAX_LEN + 1];
+ u16 version;
+ const char *cfg_name;
+ bool reset_controller_at_probe;
+ bool load_cfg_from_disk;
+ struct completion firmware_loading_complete;
+ unsigned long irq_flags;
+ enum goodix_irq_pin_access_method irq_pin_access_method;
+ unsigned int contact_size;
+ u8 config[GOODIX_CONFIG_MAX_LENGTH];
+ unsigned short keymap[GOODIX_MAX_KEYS];
+};
+
static int goodix_check_cfg_8(struct goodix_ts_data *ts,
- const struct firmware *cfg);
+ const u8 *cfg, int len);
static int goodix_check_cfg_16(struct goodix_ts_data *ts,
- const struct firmware *cfg);
+ const u8 *cfg, int len);
+static void goodix_calc_cfg_checksum_8(struct goodix_ts_data *ts);
+static void goodix_calc_cfg_checksum_16(struct goodix_ts_data *ts);
static const struct goodix_chip_data gt1x_chip_data = {
.config_addr = GOODIX_GT1X_REG_CONFIG_DATA,
- .config_len = GOODIX_CONFIG_MAX_LENGTH,
+ .config_len = GOODIX_CONFIG_GT9X_LENGTH,
.check_config = goodix_check_cfg_16,
+ .calc_config_checksum = goodix_calc_cfg_checksum_16,
};
static const struct goodix_chip_data gt911_chip_data = {
.config_addr = GOODIX_GT9X_REG_CONFIG_DATA,
.config_len = GOODIX_CONFIG_911_LENGTH,
.check_config = goodix_check_cfg_8,
+ .calc_config_checksum = goodix_calc_cfg_checksum_8,
};
static const struct goodix_chip_data gt967_chip_data = {
.config_addr = GOODIX_GT9X_REG_CONFIG_DATA,
.config_len = GOODIX_CONFIG_967_LENGTH,
.check_config = goodix_check_cfg_8,
+ .calc_config_checksum = goodix_calc_cfg_checksum_8,
};
static const struct goodix_chip_data gt9x_chip_data = {
.config_addr = GOODIX_GT9X_REG_CONFIG_DATA,
- .config_len = GOODIX_CONFIG_MAX_LENGTH,
+ .config_len = GOODIX_CONFIG_GT9X_LENGTH,
.check_config = goodix_check_cfg_8,
+ .calc_config_checksum = goodix_calc_cfg_checksum_8,
+};
+
+static const struct goodix_chip_id goodix_chip_ids[] = {
+ { .id = "1151", .data = &gt1x_chip_data },
+ { .id = "5663", .data = &gt1x_chip_data },
+ { .id = "5688", .data = &gt1x_chip_data },
+ { .id = "917S", .data = &gt1x_chip_data },
+
+ { .id = "911", .data = &gt911_chip_data },
+ { .id = "9271", .data = &gt911_chip_data },
+ { .id = "9110", .data = &gt911_chip_data },
+ { .id = "927", .data = &gt911_chip_data },
+ { .id = "928", .data = &gt911_chip_data },
+
+ { .id = "912", .data = &gt967_chip_data },
+ { .id = "9147", .data = &gt967_chip_data },
+ { .id = "967", .data = &gt967_chip_data },
+ { }
};
static const unsigned long goodix_irq_flags[] = {
@@ -168,6 +223,22 @@ static const struct dmi_system_id nine_bytes_report[] = {
{}
};
+/*
+ * Those tablets have their x coordinate inverted
+ */
+static const struct dmi_system_id inverted_x_screen[] = {
+#if defined(CONFIG_DMI) && defined(CONFIG_X86)
+ {
+ .ident = "Cube I15-TC",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Cube"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "I15-TC")
+ },
+ },
+#endif
+ {}
+};
+
/**
* goodix_i2c_read - read data from a register of the i2c slave device.
*
@@ -235,28 +306,16 @@ static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
return goodix_i2c_write(client, reg, &value, sizeof(value));
}
-static const struct goodix_chip_data *goodix_get_chip_data(u16 id)
+static const struct goodix_chip_data *goodix_get_chip_data(const char *id)
{
- switch (id) {
- case 1151:
- case 5663:
- case 5688:
- return &gt1x_chip_data;
-
- case 911:
- case 9271:
- case 9110:
- case 927:
- case 928:
- return &gt911_chip_data;
-
- case 912:
- case 967:
- return &gt967_chip_data;
+ unsigned int i;
- default:
- return &gt9x_chip_data;
+ for (i = 0; goodix_chip_ids[i].id; i++) {
+ if (!strcmp(goodix_chip_ids[i].id, id))
+ return goodix_chip_ids[i].data;
}
+
+ return &gt9x_chip_data;
}
static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
@@ -264,6 +323,13 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
unsigned long max_timeout;
int touch_num;
int error;
+ u16 addr = GOODIX_READ_COOR_ADDR;
+ /*
+ * We are going to read 1-byte header,
+ * ts->contact_size * max(1, touch_num) bytes of coordinates
+ * and 1-byte footer which contains the touch-key code.
+ */
+ const int header_contact_keycode_size = 1 + ts->contact_size + 1;
/*
* The 'buffer status' bit, which indicates that the data is valid, is
@@ -272,8 +338,8 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
*/
max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT);
do {
- error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR,
- data, ts->contact_size + 1);
+ error = goodix_i2c_read(ts->client, addr, data,
+ header_contact_keycode_size);
if (error) {
dev_err(&ts->client->dev, "I2C transfer error: %d\n",
error);
@@ -286,11 +352,10 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
return -EPROTO;
if (touch_num > 1) {
- data += 1 + ts->contact_size;
+ addr += header_contact_keycode_size;
+ data += header_contact_keycode_size;
error = goodix_i2c_read(ts->client,
- GOODIX_READ_COOR_ADDR +
- 1 + ts->contact_size,
- data,
+ addr, data,
ts->contact_size *
(touch_num - 1));
if (error)
@@ -307,7 +372,7 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
* The Goodix panel will send spurious interrupts after a
* 'finger up' event, which will always cause a timeout.
*/
- return 0;
+ return -ENOMSG;
}
static void goodix_ts_report_touch_8b(struct goodix_ts_data *ts, u8 *coor_data)
@@ -340,6 +405,25 @@ static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
}
+static void goodix_ts_report_key(struct goodix_ts_data *ts, u8 *data)
+{
+ int touch_num;
+ u8 key_value;
+ int i;
+
+ if (data[0] & GOODIX_HAVE_KEY) {
+ touch_num = data[0] & 0x0f;
+ key_value = data[1 + ts->contact_size * touch_num];
+ for (i = 0; i < GOODIX_MAX_KEYS; i++)
+ if (key_value & BIT(i))
+ input_report_key(ts->input_dev,
+ ts->keymap[i], 1);
+ } else {
+ for (i = 0; i < GOODIX_MAX_KEYS; i++)
+ input_report_key(ts->input_dev, ts->keymap[i], 0);
+ }
+}
+
/**
* goodix_process_events - Process incoming events
*
@@ -350,7 +434,7 @@ static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
*/
static void goodix_process_events(struct goodix_ts_data *ts)
{
- u8 point_data[1 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
+ u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
int touch_num;
int i;
@@ -358,11 +442,7 @@ static void goodix_process_events(struct goodix_ts_data *ts)
if (touch_num < 0)
return;
- /*
- * Bit 4 of the first byte reports the status of the capacitive
- * Windows/Home button.
- */
- input_report_key(ts->input_dev, KEY_LEFTMETA, point_data[0] & BIT(4));
+ goodix_ts_report_key(ts, point_data);
for (i = 0; i < touch_num; i++)
if (ts->contact_size == 9)
@@ -406,22 +486,21 @@ static int goodix_request_irq(struct goodix_ts_data *ts)
ts->irq_flags, ts->client->name, ts);
}
-static int goodix_check_cfg_8(struct goodix_ts_data *ts,
- const struct firmware *cfg)
+static int goodix_check_cfg_8(struct goodix_ts_data *ts, const u8 *cfg, int len)
{
- int i, raw_cfg_len = cfg->size - 2;
+ int i, raw_cfg_len = len - 2;
u8 check_sum = 0;
for (i = 0; i < raw_cfg_len; i++)
- check_sum += cfg->data[i];
+ check_sum += cfg[i];
check_sum = (~check_sum) + 1;
- if (check_sum != cfg->data[raw_cfg_len]) {
+ if (check_sum != cfg[raw_cfg_len]) {
dev_err(&ts->client->dev,
"The checksum of the config fw is not correct");
return -EINVAL;
}
- if (cfg->data[raw_cfg_len + 1] != 1) {
+ if (cfg[raw_cfg_len + 1] != 1) {
dev_err(&ts->client->dev,
"Config fw must have Config_Fresh register set");
return -EINVAL;
@@ -430,22 +509,35 @@ static int goodix_check_cfg_8(struct goodix_ts_data *ts,
return 0;
}
-static int goodix_check_cfg_16(struct goodix_ts_data *ts,
- const struct firmware *cfg)
+static void goodix_calc_cfg_checksum_8(struct goodix_ts_data *ts)
{
- int i, raw_cfg_len = cfg->size - 3;
+ int i, raw_cfg_len = ts->chip->config_len - 2;
+ u8 check_sum = 0;
+
+ for (i = 0; i < raw_cfg_len; i++)
+ check_sum += ts->config[i];
+ check_sum = (~check_sum) + 1;
+
+ ts->config[raw_cfg_len] = check_sum;
+ ts->config[raw_cfg_len + 1] = 1; /* Set "config_fresh" bit */
+}
+
+static int goodix_check_cfg_16(struct goodix_ts_data *ts, const u8 *cfg,
+ int len)
+{
+ int i, raw_cfg_len = len - 3;
u16 check_sum = 0;
for (i = 0; i < raw_cfg_len; i += 2)
- check_sum += get_unaligned_be16(&cfg->data[i]);
+ check_sum += get_unaligned_be16(&cfg[i]);
check_sum = (~check_sum) + 1;
- if (check_sum != get_unaligned_be16(&cfg->data[raw_cfg_len])) {
+ if (check_sum != get_unaligned_be16(&cfg[raw_cfg_len])) {
dev_err(&ts->client->dev,
"The checksum of the config fw is not correct");
return -EINVAL;
}
- if (cfg->data[raw_cfg_len + 2] != 1) {
+ if (cfg[raw_cfg_len + 2] != 1) {
dev_err(&ts->client->dev,
"Config fw must have Config_Fresh register set");
return -EINVAL;
@@ -454,22 +546,35 @@ static int goodix_check_cfg_16(struct goodix_ts_data *ts,
return 0;
}
+static void goodix_calc_cfg_checksum_16(struct goodix_ts_data *ts)
+{
+ int i, raw_cfg_len = ts->chip->config_len - 3;
+ u16 check_sum = 0;
+
+ for (i = 0; i < raw_cfg_len; i += 2)
+ check_sum += get_unaligned_be16(&ts->config[i]);
+ check_sum = (~check_sum) + 1;
+
+ put_unaligned_be16(check_sum, &ts->config[raw_cfg_len]);
+ ts->config[raw_cfg_len + 2] = 1; /* Set "config_fresh" bit */
+}
+
/**
* goodix_check_cfg - Checks if config fw is valid
*
* @ts: goodix_ts_data pointer
* @cfg: firmware config data
*/
-static int goodix_check_cfg(struct goodix_ts_data *ts,
- const struct firmware *cfg)
+static int goodix_check_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len)
{
- if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
+ if (len < GOODIX_CONFIG_MIN_LENGTH ||
+ len > GOODIX_CONFIG_MAX_LENGTH) {
dev_err(&ts->client->dev,
"The length of the config fw is not correct");
return -EINVAL;
}
- return ts->chip->check_config(ts, cfg);
+ return ts->chip->check_config(ts, cfg, len);
}
/**
@@ -478,17 +583,15 @@ static int goodix_check_cfg(struct goodix_ts_data *ts,
* @ts: goodix_ts_data pointer
* @cfg: config firmware to write to device
*/
-static int goodix_send_cfg(struct goodix_ts_data *ts,
- const struct firmware *cfg)
+static int goodix_send_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len)
{
int error;
- error = goodix_check_cfg(ts, cfg);
+ error = goodix_check_cfg(ts, cfg, len);
if (error)
return error;
- error = goodix_i2c_write(ts->client, ts->chip->config_addr, cfg->data,
- cfg->size);
+ error = goodix_i2c_write(ts->client, ts->chip->config_addr, cfg, len);
if (error) {
dev_err(&ts->client->dev, "Failed to write config data: %d",
error);
@@ -502,17 +605,93 @@ static int goodix_send_cfg(struct goodix_ts_data *ts,
return 0;
}
+#ifdef ACPI_GPIO_SUPPORT
+static int goodix_pin_acpi_direction_input(struct goodix_ts_data *ts)
+{
+ acpi_handle handle = ACPI_HANDLE(&ts->client->dev);
+ acpi_status status;
+
+ status = acpi_evaluate_object(handle, "INTI", NULL, NULL);
+ return ACPI_SUCCESS(status) ? 0 : -EIO;
+}
+
+static int goodix_pin_acpi_output_method(struct goodix_ts_data *ts, int value)
+{
+ acpi_handle handle = ACPI_HANDLE(&ts->client->dev);
+ acpi_status status;
+
+ status = acpi_execute_simple_method(handle, "INTO", value);
+ return ACPI_SUCCESS(status) ? 0 : -EIO;
+}
+#else
+static int goodix_pin_acpi_direction_input(struct goodix_ts_data *ts)
+{
+ dev_err(&ts->client->dev,
+ "%s called on device without ACPI support\n", __func__);
+ return -EINVAL;
+}
+
+static int goodix_pin_acpi_output_method(struct goodix_ts_data *ts, int value)
+{
+ dev_err(&ts->client->dev,
+ "%s called on device without ACPI support\n", __func__);
+ return -EINVAL;
+}
+#endif
+
+static int goodix_irq_direction_output(struct goodix_ts_data *ts, int value)
+{
+ switch (ts->irq_pin_access_method) {
+ case IRQ_PIN_ACCESS_NONE:
+ dev_err(&ts->client->dev,
+ "%s called without an irq_pin_access_method set\n",
+ __func__);
+ return -EINVAL;
+ case IRQ_PIN_ACCESS_GPIO:
+ return gpiod_direction_output(ts->gpiod_int, value);
+ case IRQ_PIN_ACCESS_ACPI_GPIO:
+ /*
+ * The IRQ pin triggers on a falling edge, so its gets marked
+ * as active-low, use output_raw to avoid the value inversion.
+ */
+ return gpiod_direction_output_raw(ts->gpiod_int, value);
+ case IRQ_PIN_ACCESS_ACPI_METHOD:
+ return goodix_pin_acpi_output_method(ts, value);
+ }
+
+ return -EINVAL; /* Never reached */
+}
+
+static int goodix_irq_direction_input(struct goodix_ts_data *ts)
+{
+ switch (ts->irq_pin_access_method) {
+ case IRQ_PIN_ACCESS_NONE:
+ dev_err(&ts->client->dev,
+ "%s called without an irq_pin_access_method set\n",
+ __func__);
+ return -EINVAL;
+ case IRQ_PIN_ACCESS_GPIO:
+ return gpiod_direction_input(ts->gpiod_int);
+ case IRQ_PIN_ACCESS_ACPI_GPIO:
+ return gpiod_direction_input(ts->gpiod_int);
+ case IRQ_PIN_ACCESS_ACPI_METHOD:
+ return goodix_pin_acpi_direction_input(ts);
+ }
+
+ return -EINVAL; /* Never reached */
+}
+
static int goodix_int_sync(struct goodix_ts_data *ts)
{
int error;
- error = gpiod_direction_output(ts->gpiod_int, 0);
+ error = goodix_irq_direction_output(ts, 0);
if (error)
return error;
msleep(50); /* T5: 50ms */
- error = gpiod_direction_input(ts->gpiod_int);
+ error = goodix_irq_direction_input(ts);
if (error)
return error;
@@ -536,7 +715,7 @@ static int goodix_reset(struct goodix_ts_data *ts)
msleep(20); /* T2: > 10ms */
/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
- error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+ error = goodix_irq_direction_output(ts, ts->client->addr == 0x14);
if (error)
return error;
@@ -560,6 +739,124 @@ static int goodix_reset(struct goodix_ts_data *ts)
return 0;
}
+#ifdef ACPI_GPIO_SUPPORT
+#include <asm/cpu_device_id.h>
+#include <asm/intel-family.h>
+
+static const struct x86_cpu_id baytrail_cpu_ids[] = {
+ { X86_VENDOR_INTEL, 6, INTEL_FAM6_ATOM_SILVERMONT, X86_FEATURE_ANY, },
+ {}
+};
+
+static inline bool is_byt(void)
+{
+ const struct x86_cpu_id *id = x86_match_cpu(baytrail_cpu_ids);
+
+ return !!id;
+}
+
+static const struct acpi_gpio_params first_gpio = { 0, 0, false };
+static const struct acpi_gpio_params second_gpio = { 1, 0, false };
+
+static const struct acpi_gpio_mapping acpi_goodix_int_first_gpios[] = {
+ { GOODIX_GPIO_INT_NAME "-gpios", &first_gpio, 1 },
+ { GOODIX_GPIO_RST_NAME "-gpios", &second_gpio, 1 },
+ { },
+};
+
+static const struct acpi_gpio_mapping acpi_goodix_int_last_gpios[] = {
+ { GOODIX_GPIO_RST_NAME "-gpios", &first_gpio, 1 },
+ { GOODIX_GPIO_INT_NAME "-gpios", &second_gpio, 1 },
+ { },
+};
+
+static const struct acpi_gpio_mapping acpi_goodix_reset_only_gpios[] = {
+ { GOODIX_GPIO_RST_NAME "-gpios", &first_gpio, 1 },
+ { },
+};
+
+static int goodix_resource(struct acpi_resource *ares, void *data)
+{
+ struct goodix_ts_data *ts = data;
+ struct device *dev = &ts->client->dev;
+ struct acpi_resource_gpio *gpio;
+
+ switch (ares->type) {
+ case ACPI_RESOURCE_TYPE_GPIO:
+ gpio = &ares->data.gpio;
+ if (gpio->connection_type == ACPI_RESOURCE_GPIO_TYPE_INT) {
+ if (ts->gpio_int_idx == -1) {
+ ts->gpio_int_idx = ts->gpio_count;
+ } else {
+ dev_err(dev, "More then one GpioInt resource, ignoring ACPI GPIO resources\n");
+ ts->gpio_int_idx = -2;
+ }
+ }
+ ts->gpio_count++;
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/*
+ * This function gets called in case we fail to get the irq GPIO directly
+ * because the ACPI tables lack GPIO-name to APCI _CRS index mappings
+ * (no _DSD UUID daffd814-6eba-4d8c-8a91-bc9bbf4aa301 data).
+ * In that case we add our own mapping and then goodix_get_gpio_config()
+ * retries to get the GPIOs based on the added mapping.
+ */
+static int goodix_add_acpi_gpio_mappings(struct goodix_ts_data *ts)
+{
+ const struct acpi_gpio_mapping *gpio_mapping = NULL;
+ struct device *dev = &ts->client->dev;
+ LIST_HEAD(resources);
+ int ret;
+
+ ts->gpio_count = 0;
+ ts->gpio_int_idx = -1;
+ ret = acpi_dev_get_resources(ACPI_COMPANION(dev), &resources,
+ goodix_resource, ts);
+ if (ret < 0) {
+ dev_err(dev, "Error getting ACPI resources: %d\n", ret);
+ return ret;
+ }
+
+ acpi_dev_free_resource_list(&resources);
+
+ if (ts->gpio_count == 2 && ts->gpio_int_idx == 0) {
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
+ gpio_mapping = acpi_goodix_int_first_gpios;
+ } else if (ts->gpio_count == 2 && ts->gpio_int_idx == 1) {
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
+ gpio_mapping = acpi_goodix_int_last_gpios;
+ } else if (ts->gpio_count == 1 && ts->gpio_int_idx == -1 &&
+ acpi_has_method(ACPI_HANDLE(dev), "INTI") &&
+ acpi_has_method(ACPI_HANDLE(dev), "INTO")) {
+ dev_info(dev, "Using ACPI INTI and INTO methods for IRQ pin access\n");
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_METHOD;
+ gpio_mapping = acpi_goodix_reset_only_gpios;
+ } else if (is_byt() && ts->gpio_count == 2 && ts->gpio_int_idx == -1) {
+ dev_info(dev, "No ACPI GpioInt resource, assuming that the GPIO order is reset, int\n");
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
+ gpio_mapping = acpi_goodix_int_last_gpios;
+ } else {
+ dev_warn(dev, "Unexpected ACPI resources: gpio_count %d, gpio_int_idx %d\n",
+ ts->gpio_count, ts->gpio_int_idx);
+ return -EINVAL;
+ }
+
+ return devm_acpi_dev_add_driver_gpios(dev, gpio_mapping);
+}
+#else
+static int goodix_add_acpi_gpio_mappings(struct goodix_ts_data *ts)
+{
+ return -EINVAL;
+}
+#endif /* CONFIG_X86 && CONFIG_ACPI */
+
/**
* goodix_get_gpio_config - Get GPIO config from ACPI/DT
*
@@ -570,6 +867,7 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
int error;
struct device *dev;
struct gpio_desc *gpiod;
+ bool added_acpi_mappings = false;
if (!ts->client)
return -EINVAL;
@@ -593,6 +891,7 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
return error;
}
+retry_get_irq_gpio:
/* Get the interrupt GPIO pin number */
gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
if (IS_ERR(gpiod)) {
@@ -602,6 +901,11 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
GOODIX_GPIO_INT_NAME, error);
return error;
}
+ if (!gpiod && has_acpi_companion(dev) && !added_acpi_mappings) {
+ added_acpi_mappings = true;
+ if (goodix_add_acpi_gpio_mappings(ts) == 0)
+ goto retry_get_irq_gpio;
+ }
ts->gpiod_int = gpiod;
@@ -617,6 +921,31 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
ts->gpiod_rst = gpiod;
+ switch (ts->irq_pin_access_method) {
+ case IRQ_PIN_ACCESS_ACPI_GPIO:
+ /*
+ * We end up here if goodix_add_acpi_gpio_mappings() has
+ * called devm_acpi_dev_add_driver_gpios() because the ACPI
+ * tables did not contain name to index mappings.
+ * Check that we successfully got both GPIOs after we've
+ * added our own acpi_gpio_mapping and if we did not get both
+ * GPIOs reset irq_pin_access_method to IRQ_PIN_ACCESS_NONE.
+ */
+ if (!ts->gpiod_int || !ts->gpiod_rst)
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE;
+ break;
+ case IRQ_PIN_ACCESS_ACPI_METHOD:
+ if (!ts->gpiod_rst)
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE;
+ break;
+ default:
+ if (ts->gpiod_int && ts->gpiod_rst) {
+ ts->reset_controller_at_probe = true;
+ ts->load_cfg_from_disk = true;
+ ts->irq_pin_access_method = IRQ_PIN_ACCESS_GPIO;
+ }
+ }
+
return 0;
}
@@ -629,12 +958,11 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
*/
static void goodix_read_config(struct goodix_ts_data *ts)
{
- u8 config[GOODIX_CONFIG_MAX_LENGTH];
int x_max, y_max;
int error;
error = goodix_i2c_read(ts->client, ts->chip->config_addr,
- config, ts->chip->config_len);
+ ts->config, ts->chip->config_len);
if (error) {
dev_warn(&ts->client->dev, "Error reading config: %d\n",
error);
@@ -643,15 +971,17 @@ static void goodix_read_config(struct goodix_ts_data *ts)
return;
}
- ts->int_trigger_type = config[TRIGGER_LOC] & 0x03;
- ts->max_touch_num = config[MAX_CONTACTS_LOC] & 0x0f;
+ ts->int_trigger_type = ts->config[TRIGGER_LOC] & 0x03;
+ ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
- x_max = get_unaligned_le16(&config[RESOLUTION_LOC]);
- y_max = get_unaligned_le16(&config[RESOLUTION_LOC + 2]);
+ x_max = get_unaligned_le16(&ts->config[RESOLUTION_LOC]);
+ y_max = get_unaligned_le16(&ts->config[RESOLUTION_LOC + 2]);
if (x_max && y_max) {
input_abs_set_max(ts->input_dev, ABS_MT_POSITION_X, x_max - 1);
input_abs_set_max(ts->input_dev, ABS_MT_POSITION_Y, y_max - 1);
}
+
+ ts->chip->calc_config_checksum(ts);
}
/**
@@ -663,7 +993,7 @@ static int goodix_read_version(struct goodix_ts_data *ts)
{
int error;
u8 buf[6];
- char id_str[5];
+ char id_str[GOODIX_ID_MAX_LEN + 1];
error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
if (error) {
@@ -671,14 +1001,13 @@ static int goodix_read_version(struct goodix_ts_data *ts)
return error;
}
- memcpy(id_str, buf, 4);
- id_str[4] = 0;
- if (kstrtou16(id_str, 10, &ts->id))
- ts->id = 0x1001;
+ memcpy(id_str, buf, GOODIX_ID_MAX_LEN);
+ id_str[GOODIX_ID_MAX_LEN] = 0;
+ strscpy(ts->id, id_str, GOODIX_ID_MAX_LEN + 1);
ts->version = get_unaligned_le16(&buf[4]);
- dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id,
+ dev_info(&ts->client->dev, "ID %s, version: %04x\n", ts->id,
ts->version);
return 0;
@@ -722,6 +1051,7 @@ static int goodix_i2c_test(struct i2c_client *client)
static int goodix_configure_dev(struct goodix_ts_data *ts)
{
int error;
+ int i;
ts->int_trigger_type = GOODIX_INT_TRIGGER;
ts->max_touch_num = GOODIX_MAX_CONTACTS;
@@ -736,11 +1066,23 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
ts->input_dev->phys = "input/ts";
ts->input_dev->id.bustype = BUS_I2C;
ts->input_dev->id.vendor = 0x0416;
- ts->input_dev->id.product = ts->id;
+ if (kstrtou16(ts->id, 10, &ts->input_dev->id.product))
+ ts->input_dev->id.product = 0x1001;
ts->input_dev->id.version = ts->version;
+ ts->input_dev->keycode = ts->keymap;
+ ts->input_dev->keycodesize = sizeof(ts->keymap[0]);
+ ts->input_dev->keycodemax = GOODIX_MAX_KEYS;
+
/* Capacitive Windows/Home button on some devices */
- input_set_capability(ts->input_dev, EV_KEY, KEY_LEFTMETA);
+ for (i = 0; i < GOODIX_MAX_KEYS; ++i) {
+ if (i == 0)
+ ts->keymap[i] = KEY_LEFTMETA;
+ else
+ ts->keymap[i] = KEY_F1 + (i - 1);
+
+ input_set_capability(ts->input_dev, EV_KEY, ts->keymap[i]);
+ }
input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X);
input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y);
@@ -780,6 +1122,12 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
"Non-standard 9-bytes report format quirk\n");
}
+ if (dmi_check_system(inverted_x_screen)) {
+ ts->prop.invert_x = true;
+ dev_dbg(&ts->client->dev,
+ "Applying 'inverted x screen' quirk\n");
+ }
+
error = input_mt_init_slots(ts->input_dev, ts->max_touch_num,
INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
if (error) {
@@ -820,7 +1168,7 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
if (cfg) {
/* send device configuration to the firmware */
- error = goodix_send_cfg(ts, cfg);
+ error = goodix_send_cfg(ts, cfg->data, cfg->size);
if (error)
goto err_release_cfg;
}
@@ -889,7 +1237,8 @@ static int goodix_ts_probe(struct i2c_client *client,
if (error)
return error;
- if (ts->gpiod_int && ts->gpiod_rst) {
+reset:
+ if (ts->reset_controller_at_probe) {
/* reset the controller */
error = goodix_reset(ts);
if (error) {
@@ -900,6 +1249,12 @@ static int goodix_ts_probe(struct i2c_client *client,
error = goodix_i2c_test(client);
if (error) {
+ if (!ts->reset_controller_at_probe &&
+ ts->irq_pin_access_method != IRQ_PIN_ACCESS_NONE) {
+ /* Retry after a controller reset */
+ ts->reset_controller_at_probe = true;
+ goto reset;
+ }
dev_err(&client->dev, "I2C communication failure: %d\n", error);
return error;
}
@@ -912,10 +1267,10 @@ static int goodix_ts_probe(struct i2c_client *client,
ts->chip = goodix_get_chip_data(ts->id);
- if (ts->gpiod_int && ts->gpiod_rst) {
+ if (ts->load_cfg_from_disk) {
/* update device config */
ts->cfg_name = devm_kasprintf(&client->dev, GFP_KERNEL,
- "goodix_%d_cfg.bin", ts->id);
+ "goodix_%s_cfg.bin", ts->id);
if (!ts->cfg_name)
return -ENOMEM;
@@ -943,7 +1298,7 @@ static int goodix_ts_remove(struct i2c_client *client)
{
struct goodix_ts_data *ts = i2c_get_clientdata(client);
- if (ts->gpiod_int && ts->gpiod_rst)
+ if (ts->load_cfg_from_disk)
wait_for_completion(&ts->firmware_loading_complete);
return 0;
@@ -955,19 +1310,20 @@ static int __maybe_unused goodix_suspend(struct device *dev)
struct goodix_ts_data *ts = i2c_get_clientdata(client);
int error;
+ if (ts->load_cfg_from_disk)
+ wait_for_completion(&ts->firmware_loading_complete);
+
/* We need gpio pins to suspend/resume */
- if (!ts->gpiod_int || !ts->gpiod_rst) {
+ if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_NONE) {
disable_irq(client->irq);
return 0;
}
- wait_for_completion(&ts->firmware_loading_complete);
-
/* Free IRQ as IRQ pin is used as output in the suspend sequence */
goodix_free_irq(ts);
/* Output LOW on the INT pin for 5 ms */
- error = gpiod_direction_output(ts->gpiod_int, 0);
+ error = goodix_irq_direction_output(ts, 0);
if (error) {
goodix_request_irq(ts);
return error;
@@ -979,7 +1335,7 @@ static int __maybe_unused goodix_suspend(struct device *dev)
GOODIX_CMD_SCREEN_OFF);
if (error) {
dev_err(&ts->client->dev, "Screen off command failed\n");
- gpiod_direction_input(ts->gpiod_int);
+ goodix_irq_direction_input(ts);
goodix_request_irq(ts);
return -EAGAIN;
}
@@ -997,9 +1353,10 @@ static int __maybe_unused goodix_resume(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct goodix_ts_data *ts = i2c_get_clientdata(client);
+ u8 config_ver;
int error;
- if (!ts->gpiod_int || !ts->gpiod_rst) {
+ if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_NONE) {
enable_irq(client->irq);
return 0;
}
@@ -1008,7 +1365,7 @@ static int __maybe_unused goodix_resume(struct device *dev)
* Exit sleep mode by outputting HIGH level to INT pin
* for 2ms~5ms.
*/
- error = gpiod_direction_output(ts->gpiod_int, 1);
+ error = goodix_irq_direction_output(ts, 1);
if (error)
return error;
@@ -1018,6 +1375,27 @@ static int __maybe_unused goodix_resume(struct device *dev)
if (error)
return error;
+ error = goodix_i2c_read(ts->client, ts->chip->config_addr,
+ &config_ver, 1);
+ if (error)
+ dev_warn(dev, "Error reading config version: %d, resetting controller\n",
+ error);
+ else if (config_ver != ts->config[0])
+ dev_info(dev, "Config version mismatch %d != %d, resetting controller\n",
+ config_ver, ts->config[0]);
+
+ if (error != 0 || config_ver != ts->config[0]) {
+ error = goodix_reset(ts);
+ if (error) {
+ dev_err(dev, "Controller reset failed.\n");
+ return error;
+ }
+
+ error = goodix_send_cfg(ts, ts->config, ts->chip->config_len);
+ if (error)
+ return error;
+ }
+
error = goodix_request_irq(ts);
if (error)
return error;
@@ -1050,6 +1428,8 @@ static const struct of_device_id goodix_of_match[] = {
{ .compatible = "goodix,gt911" },
{ .compatible = "goodix,gt9110" },
{ .compatible = "goodix,gt912" },
+ { .compatible = "goodix,gt9147" },
+ { .compatible = "goodix,gt917s" },
{ .compatible = "goodix,gt927" },
{ .compatible = "goodix,gt9271" },
{ .compatible = "goodix,gt928" },
diff --git a/drivers/input/touchscreen/of_touchscreen.c b/drivers/input/touchscreen/of_touchscreen.c
index e16ec4c7043a..97342e14b4f1 100644
--- a/drivers/input/touchscreen/of_touchscreen.c
+++ b/drivers/input/touchscreen/of_touchscreen.c
@@ -66,7 +66,7 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
{
struct device *dev = input->dev.parent;
struct input_absinfo *absinfo;
- unsigned int axis;
+ unsigned int axis, axis_x, axis_y;
unsigned int minimum, maximum, fuzz;
bool data_present;
@@ -74,33 +74,34 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
if (!input->absinfo)
return;
- axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
+ axis_x = multitouch ? ABS_MT_POSITION_X : ABS_X;
+ axis_y = multitouch ? ABS_MT_POSITION_Y : ABS_Y;
+
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
- input_abs_get_min(input, axis),
+ input_abs_get_min(input, axis_x),
&minimum) |
touchscreen_get_prop_u32(dev, "touchscreen-size-x",
input_abs_get_max(input,
- axis) + 1,
+ axis_x) + 1,
&maximum) |
touchscreen_get_prop_u32(dev, "touchscreen-fuzz-x",
- input_abs_get_fuzz(input, axis),
+ input_abs_get_fuzz(input, axis_x),
&fuzz);
if (data_present)
- touchscreen_set_params(input, axis, minimum, maximum - 1, fuzz);
+ touchscreen_set_params(input, axis_x, minimum, maximum - 1, fuzz);
- axis = multitouch ? ABS_MT_POSITION_Y : ABS_Y;
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-y",
- input_abs_get_min(input, axis),
+ input_abs_get_min(input, axis_y),
&minimum) |
touchscreen_get_prop_u32(dev, "touchscreen-size-y",
input_abs_get_max(input,
- axis) + 1,
+ axis_y) + 1,
&maximum) |
touchscreen_get_prop_u32(dev, "touchscreen-fuzz-y",
- input_abs_get_fuzz(input, axis),
+ input_abs_get_fuzz(input, axis_y),
&fuzz);
if (data_present)
- touchscreen_set_params(input, axis, minimum, maximum - 1, fuzz);
+ touchscreen_set_params(input, axis_y, minimum, maximum - 1, fuzz);
axis = multitouch ? ABS_MT_PRESSURE : ABS_PRESSURE;
data_present = touchscreen_get_prop_u32(dev,
@@ -117,15 +118,13 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
if (!prop)
return;
- axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
-
- prop->max_x = input_abs_get_max(input, axis);
- prop->max_y = input_abs_get_max(input, axis + 1);
+ prop->max_x = input_abs_get_max(input, axis_x);
+ prop->max_y = input_abs_get_max(input, axis_y);
prop->invert_x =
device_property_read_bool(dev, "touchscreen-inverted-x");
if (prop->invert_x) {
- absinfo = &input->absinfo[axis];
+ absinfo = &input->absinfo[axis_x];
absinfo->maximum -= absinfo->minimum;
absinfo->minimum = 0;
}
@@ -133,7 +132,7 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
prop->invert_y =
device_property_read_bool(dev, "touchscreen-inverted-y");
if (prop->invert_y) {
- absinfo = &input->absinfo[axis + 1];
+ absinfo = &input->absinfo[axis_y];
absinfo->maximum -= absinfo->minimum;
absinfo->minimum = 0;
}
@@ -141,7 +140,7 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
prop->swap_x_y =
device_property_read_bool(dev, "touchscreen-swapped-x-y");
if (prop->swap_x_y)
- swap(input->absinfo[axis], input->absinfo[axis + 1]);
+ swap(input->absinfo[axis_x], input->absinfo[axis_y]);
}
EXPORT_SYMBOL(touchscreen_parse_properties);
diff --git a/include/uapi/linux/input-event-codes.h b/include/uapi/linux/input-event-codes.h
index 6923dc7e0298..b6a835d37826 100644
--- a/include/uapi/linux/input-event-codes.h
+++ b/include/uapi/linux/input-event-codes.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/* SPDX-License-Identifier: GPL-2.0-only WITH Linux-syscall-note */
/*
* Input event codes
*
generated by cgit v1.2.3-58-ga151 (git 2.39.0) at 2024-12-21 10:43:14 +0000