diff options
| -rw-r--r-- | drivers/gpio/gpio-sx150x.c | 60 | ||||
| -rw-r--r-- | include/linux/i2c/sx150x.h | 82 |
2 files changed, 59 insertions, 83 deletions
diff --git a/drivers/gpio/gpio-sx150x.c b/drivers/gpio/gpio-sx150x.c index d57e8ad0bfd2..d4501d5f8b8e 100644 --- a/drivers/gpio/gpio-sx150x.c +++ b/drivers/gpio/gpio-sx150x.c @@ -25,7 +25,6 @@ #include <linux/irq.h> #include <linux/mutex.h> #include <linux/slab.h> -#include <linux/i2c/sx150x.h> #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_irq.h> @@ -85,6 +84,65 @@ struct sx150x_device_data { } pri; }; +/** + * struct sx150x_platform_data - config data for SX150x driver + * @gpio_base: The index number of the first GPIO assigned to this + * GPIO expander. The expander will create a block of + * consecutively numbered gpios beginning at the given base, + * with the size of the block depending on the model of the + * expander chip. + * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO + * instead of as an oscillator, increasing the size of the + * GP(I)O pool created by this expander by one. The + * output-only GPO pin will be added at the end of the block. + * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor + * for each IO line in the expander. Setting the bit at + * position n will enable the pull-up for the IO at + * the corresponding offset. For chips with fewer than + * 16 IO pins, high-end bits are ignored. + * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down + * resistor for each IO line in the expander. Setting the + * bit at position n will enable the pull-down for the IO at + * the corresponding offset. For chips with fewer than + * 16 IO pins, high-end bits are ignored. + * @io_open_drain_ena: A bit-mask which enables-or disables open-drain + * operation for each IO line in the expander. Setting the + * bit at position n enables open-drain operation for + * the IO at the corresponding offset. Clearing the bit + * enables regular push-pull operation for that IO. + * For chips with fewer than 16 IO pins, high-end bits + * are ignored. + * @io_polarity: A bit-mask which enables polarity inversion for each IO line + * in the expander. Setting the bit at position n inverts + * the polarity of that IO line, while clearing it results + * in normal polarity. For chips with fewer than 16 IO pins, + * high-end bits are ignored. + * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line + * is connected, via which it reports interrupt events + * across all GPIO lines. This must be a real, + * pre-existing IRQ line. + * Setting this value < 0 disables the irq_chip functionality + * of the driver. + * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based + * IRQ lines will appear. Similarly to gpio_base, the expander + * will create a block of irqs beginning at this number. + * This value is ignored if irq_summary is < 0. + * @reset_during_probe: If set to true, the driver will trigger a full + * reset of the chip at the beginning of the probe + * in order to place it in a known state. + */ +struct sx150x_platform_data { + unsigned gpio_base; + bool oscio_is_gpo; + u16 io_pullup_ena; + u16 io_pulldn_ena; + u16 io_open_drain_ena; + u16 io_polarity; + int irq_summary; + unsigned irq_base; + bool reset_during_probe; +}; + struct sx150x_chip { struct gpio_chip gpio_chip; struct i2c_client *client; diff --git a/include/linux/i2c/sx150x.h b/include/linux/i2c/sx150x.h deleted file mode 100644 index 52baa79d69a7..000000000000 --- a/include/linux/i2c/sx150x.h +++ /dev/null @@ -1,82 +0,0 @@ -/* - * Driver for the Semtech SX150x I2C GPIO Expanders - * - * Copyright (c) 2010, Code Aurora Forum. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA - * 02110-1301, USA. - */ -#ifndef __LINUX_I2C_SX150X_H -#define __LINUX_I2C_SX150X_H - -/** - * struct sx150x_platform_data - config data for SX150x driver - * @gpio_base: The index number of the first GPIO assigned to this - * GPIO expander. The expander will create a block of - * consecutively numbered gpios beginning at the given base, - * with the size of the block depending on the model of the - * expander chip. - * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO - * instead of as an oscillator, increasing the size of the - * GP(I)O pool created by this expander by one. The - * output-only GPO pin will be added at the end of the block. - * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor - * for each IO line in the expander. Setting the bit at - * position n will enable the pull-up for the IO at - * the corresponding offset. For chips with fewer than - * 16 IO pins, high-end bits are ignored. - * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down - * resistor for each IO line in the expander. Setting the - * bit at position n will enable the pull-down for the IO at - * the corresponding offset. For chips with fewer than - * 16 IO pins, high-end bits are ignored. - * @io_open_drain_ena: A bit-mask which enables-or disables open-drain - * operation for each IO line in the expander. Setting the - * bit at position n enables open-drain operation for - * the IO at the corresponding offset. Clearing the bit - * enables regular push-pull operation for that IO. - * For chips with fewer than 16 IO pins, high-end bits - * are ignored. - * @io_polarity: A bit-mask which enables polarity inversion for each IO line - * in the expander. Setting the bit at position n inverts - * the polarity of that IO line, while clearing it results - * in normal polarity. For chips with fewer than 16 IO pins, - * high-end bits are ignored. - * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line - * is connected, via which it reports interrupt events - * across all GPIO lines. This must be a real, - * pre-existing IRQ line. - * Setting this value < 0 disables the irq_chip functionality - * of the driver. - * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based - * IRQ lines will appear. Similarly to gpio_base, the expander - * will create a block of irqs beginning at this number. - * This value is ignored if irq_summary is < 0. - * @reset_during_probe: If set to true, the driver will trigger a full - * reset of the chip at the beginning of the probe - * in order to place it in a known state. - */ -struct sx150x_platform_data { - unsigned gpio_base; - bool oscio_is_gpo; - u16 io_pullup_ena; - u16 io_pulldn_ena; - u16 io_open_drain_ena; - u16 io_polarity; - int irq_summary; - unsigned irq_base; - bool reset_during_probe; -}; - -#endif /* __LINUX_I2C_SX150X_H */ |