diff options
| -rw-r--r-- | Documentation/devicetree/bindings/arm/gic-v3.txt | 5 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/idle-states.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/iio/accel/bma180.txt | 8 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/thermal/thermal.txt | 27 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/vendor-prefixes.txt | 1 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/mediatek/mt8173.dtsi | 2 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/rockchip/rk3368.dtsi | 2 | ||||
| -rw-r--r-- | drivers/of/of_pci_irq.c | 22 |
9 files changed, 46 insertions, 27 deletions
diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt index ddfade40ac59..7803e77d85cb 100644 --- a/Documentation/devicetree/bindings/arm/gic-v3.txt +++ b/Documentation/devicetree/bindings/arm/gic-v3.txt @@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs. These nodes must have the following properties: - compatible : Should at least contain "arm,gic-v3-its". - msi-controller : Boolean property. Identifies the node as an MSI controller +- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device + which will generate the MSI. - reg: Specifies the base physical address and size of the ITS registers. @@ -83,6 +85,7 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; }; @@ -107,12 +110,14 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; gic-its@2c400000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c400000 0 0x200000>; }; }; diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index a8274eabae2e..b8e41c148a3c 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -497,7 +497,7 @@ cpus { }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; CPU_RETENTION_0_0: cpu-retention-0-0 { compatible = "arm,idle-state"; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 5788d5cf1252..82d40e2505f6 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -16,7 +16,9 @@ properties, each containing a 'gpio-list': GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed -for new bindings. +for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old +bindings use it, but are only supported for compatibility reasons and should not +be used for newer bindings since it has been deprecated. GPIO properties can contain one or more GPIO phandles, but only in exceptional cases should they contain more than one. If your device uses several GPIOs with diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt index c5933573e0f6..4a3679d54457 100644 --- a/Documentation/devicetree/bindings/iio/accel/bma180.txt +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -1,10 +1,11 @@ -* Bosch BMA180 triaxial acceleration sensor +* Bosch BMA180 / BMA250 triaxial acceleration sensor http://omapworld.com/BMA180_111_1002839.pdf +http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf Required properties: - - compatible : should be "bosch,bma180" + - compatible : should be "bosch,bma180" or "bosch,bma250" - reg : the I2C address of the sensor Optional properties: @@ -13,6 +14,9 @@ Optional properties: - interrupts : interrupt mapping for GPIO IRQ, it should by configured with flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING + For the bma250 the first interrupt listed must be the one + connected to the INT1 pin, the second (optional) interrupt + listed must be the one connected to the INT2 pin. Example: diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 8a49362dea6e..41b817f7b670 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to the different fan speeds possible. Cooling states are referred to by single unsigned integers, where larger numbers mean greater heat dissipation. The precise set of cooling states associated with a device -(as referred to be the cooling-min-state and cooling-max-state +(as referred to by the cooling-min-level and cooling-max-level properties) should be defined in a particular device's binding. For more examples of cooling devices, refer to the example sections below. Required properties: -- cooling-min-state: An integer indicating the smallest - Type: unsigned cooling state accepted. Typically 0. - Size: one cell - -- cooling-max-state: An integer indicating the largest - Type: unsigned cooling state accepted. - Size: one cell - - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order Size: one cell to specify minimum and maximum cooling state used @@ -77,6 +69,15 @@ Required properties: See Cooling device maps section below for more details on how consumers refer to cooling devices. +Optional properties: +- cooling-min-level: An integer indicating the smallest + Type: unsigned cooling state accepted. Typically 0. + Size: one cell + +- cooling-max-level: An integer indicating the largest + Type: unsigned cooling state accepted. + Size: one cell + * Trip points The trip node is a node to describe a point in the temperature domain @@ -225,8 +226,8 @@ cpus { 396000 950000 198000 850000 >; - cooling-min-state = <0>; - cooling-max-state = <3>; + cooling-min-level = <0>; + cooling-max-level = <3>; #cooling-cells = <2>; /* min followed by max */ }; ... @@ -240,8 +241,8 @@ cpus { */ fan0: fan@0x48 { ... - cooling-min-state = <0>; - cooling-max-state = <9>; + cooling-min-level = <0>; + cooling-max-level = <9>; #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ac5f0c34ae00..82d2ac97af74 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -203,6 +203,7 @@ sitronix Sitronix Technology Corporation skyworks Skyworks Solutions, Inc. smsc Standard Microsystems Corporation snps Synopsys, Inc. +socionext Socionext Inc. solidrun SolidRun solomon Solomon Systech Limited sony Sony Corporation diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi index d18ee4259ee5..06a15644be38 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi @@ -81,7 +81,7 @@ }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; CPU_SLEEP_0: cpu-sleep-0 { compatible = "arm,idle-state"; diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index a712bea3bf2c..cc093a482aa4 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -106,7 +106,7 @@ }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; cpu_sleep: cpu-sleep-0 { compatible = "arm,idle-state"; diff --git a/drivers/of/of_pci_irq.c b/drivers/of/of_pci_irq.c index 1710d9dc7fc2..2306313c0029 100644 --- a/drivers/of/of_pci_irq.c +++ b/drivers/of/of_pci_irq.c @@ -38,8 +38,8 @@ int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args *out_irq */ rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin); if (rc != 0) - return rc; - /* No pin, exit */ + goto err; + /* No pin, exit with no error message. */ if (pin == 0) return -ENODEV; @@ -53,8 +53,10 @@ int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args *out_irq ppnode = pci_bus_to_OF_node(pdev->bus); /* No node for host bridge ? give up */ - if (ppnode == NULL) - return -EINVAL; + if (ppnode == NULL) { + rc = -EINVAL; + goto err; + } } else { /* We found a P2P bridge, check if it has a node */ ppnode = pci_device_to_OF_node(ppdev); @@ -86,7 +88,13 @@ int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args *out_irq out_irq->args[0] = pin; laddr[0] = cpu_to_be32((pdev->bus->number << 16) | (pdev->devfn << 8)); laddr[1] = laddr[2] = cpu_to_be32(0); - return of_irq_parse_raw(laddr, out_irq); + rc = of_irq_parse_raw(laddr, out_irq); + if (rc) + goto err; + return 0; +err: + dev_err(&pdev->dev, "of_irq_parse_pci() failed with rc=%d\n", rc); + return rc; } EXPORT_SYMBOL_GPL(of_irq_parse_pci); @@ -105,10 +113,8 @@ int of_irq_parse_and_map_pci(const struct pci_dev *dev, u8 slot, u8 pin) int ret; ret = of_irq_parse_pci(dev, &oirq); - if (ret) { - dev_err(&dev->dev, "of_irq_parse_pci() failed with rc=%d\n", ret); + if (ret) return 0; /* Proper return code 0 == NO_IRQ */ - } return irq_create_of_mapping(&oirq); } |